Carpetwin

™

14 / 18

Advance MODELS 56704200, 56704201

5/99 revised 11/02 Form Number 56041453

A

3

1

20

15

14

13

11

2

22

17

12

4

2

5

19

18

6

7

8

10

9

C

D

B

20

21

16

Important Safety Instructions ................................................................ 2

Grounding Instructions .......................................................................... 5

Introduction ........................................................................................... 7

Parts and Service .................................................................................. 7

Nameplate ............................................................................................. 7

Unpacking the Machine ........................................................................ 7

Know Your Machine .............................................................................. 7

Set-Up and Assembly ........................................................................... 7

Operating the Machine .......................................................................... 8

Using the Wand .................................................................................... 8

After Using the Machine ........................................................................ 8

Vacuum Motor Brushes ........................................................................ 8

Maintenance ......................................................................................... 8

Changing the Paper Dust Bag .............................................................. 8

Changing the Cloth Dust Bag ............................................................... 8

Cleaning the Vacuum Inlet Filter ........................................................... 9

Changing the Electrostat Exhaust Filter ................................................ 9

Changing the Brush .............................................................................. 9

Replacing the Belt ................................................................................. 9

Technical Specifications ....................................................................... 9

Bag Housing Parts List .................................................................. 11-12

Brush Housing Parts List ............................................................... 13-14

Wiring Diagram ................................................................................... 15

1 - FORM NO. 56041453 / CARPETWIN 14 / 18

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before using.

This machine is for commercial use, for example in hotels, schools, hospitals, factories, shops and offices other than normal residential housekeeping purposes.

THIS APPLIANCE IS INTENDED FOR DRY USE ONLY!

DO NOT USE FOR WET FLOOR OR CARPET!

WARNING !

To reduce the risk of fire, electric shock, or injury:

* Do not leave the appliance when it is plugged in. Unplug the unit from the outlet when not in use and before servicing.

WARNING !

To reduce the risk of electric shock, do not use outdoors or on wet surfaces.

* Do not allow to be used as a toy. Close attention is necessary when used by or near children.

* Use only as described in this manual. Use only the manufacturer’s recommended attachments.

* If the appliance is not working as it should be, has been dropped, damaged, left outdoors or dropped into water, return it to a service center. The machine must not be used if the electrical cord shows any sign of damage. Regularly inspect the cord for damage, particularly if it has been crushed, shut in a door or run over.

* Do not pull or carry by the cord, use the cord as a handle, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces.

* Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

* Do not handle the plug, cord or appliance with wet hands.

* Do not put any object into openings. Do not use with any opening blocked.

* Keep loose clothing, hair, fingers, and all parts of body away from openings and moving parts.

* Do not pick up anything that is burning or smoking, such as cigarettes or matches. Under no circumstances should the machine be used for picking up hot material. In particular the machine must not be used for cleaning open and closed fireplaces, ovens or similar that contain warm or glowing ashes.

* Do not use without dust bag and/or filters in place.

* Turn off all controls before unplugging. The plug must always be removed from the socket outlet before starting any service or repair work of the vacuum cleaner or the cord.

* Avoid vacuuming hard or sharp objects.

* Use extra care when cleaning on stairs.

* The machine must not be used for picking up combustible materials which are health endangering or explosive materials such as petrol (gasoline), nor should it be used in an explosive atmosphere. The machine must not be used for picking up water, other liquids or for picking up hazardous - i.e. poisonous dust.

* No changes or modifications of the mechanical, electrical or thermal safety devices should be made.

* When repairing or replacing the cord, the same type of cord as originally supplied with the machine must be used. This cord can be supplied by ADVANCE.

SAVE THESE INSTRUCTIONS

FORM NO. 56041453 / CARPETWIN 14 / 18 - 2

INSTRUCTIONS DE SÉCURITÉ IMPORTANTES

Toujours suivre certaines précautions élémentaires lors de l’utilisation d’un appareil électrique.

Lire toutes les instructions avant d’utiliser la machine.

Cette machine est adaptée à l’usage commercial, par exemple dans les hôtels, les écoles, les hôpitaux, les usines, les magasins et les bureaux.

CET APPAREIL NE DOIT ETRE UTILISE QU’A SEC!

NE PAS UTILISER SUR UNE SURFACE HUMIDE!

AVERTISSEMENT !

Pour réduire les risques d’incendie, de décharge électrique ou de blessures:

* Ne pas abandonner l’appareil s’il est branché. Débrancher l’alimentation secteur quand l’appareil n’est pas utilisé ou avant l’entretien.

AVERTISSEMENT !

Pour réduire les risques de décharges électriques, ne pas utiliser l’appareil en extérieur ou sur des surfaces humides.

* Cet appareil n’est pas un jouet. Rester attentif quand il est utilisé par ou près des enfants.

* Utiliser l’appareil conformément aux instructions de la notice. Utiliser seulement les accessoires préconisés par le fabricant.

* Ne pas utiliser l’appareil si le cable d’alimentation ou la prise est endommagé. Retourner l’appareil au centre de service aprèsvente s’il ne fonctionne pas correctement, s’il est tombé, s’il a été endommagé, s’il a été laissé à l’extérieur ou s’il est tombé dans l’eau.

* Ne pas tirer ou porter l’appareil par le cable d’alimentation, ou coincer le cable dans une porte ou tirer le cable sur des angles vifs ou des coins. Ne pas faire passer l’appareil sur le cable. Eloigner le cable des surfaces chaudes.

* Ne pas débrancher l’appareil en tirant sur le cable d’alimentation, mais en saisissant la prise.

* Ne pas manipuler la prise, le cable d’alimentation ou l’appareil avec les mains humides.

* Ne rien introduire dans les ouvertures de l’appareil. Ne pas utiliser l’appareil si l’une des ouvertures est obstruée; éliminer la poussière, les peluches, les cheveux et tout corps étranger pouvant gêner le flux d’air.

* Eloigner les vêtements amples, cheveux, doigts et toute autre partie du corps des pièces en mouvement et des ouvertures.

* Ne pas aspirer d’objets qui brûlent ou dégagent de la fumée, comme des cigarettes, des allumettes ou des cendres chaudes, ni de poussières dangereuses pour la santé. Ne pas aspirer d’eau ou des liquides.

* Ne pas utiliser sans sac à poussière et/ou filtre en place.

* Placer toutes les commandes en position d’arrêt avant de débrancher l’appareil.

* Eviter d’aspirer des corps durs ou pointus.

* Etre particulièrement prudent en nettoyant les escaliers.

* Ne pas aspirer de liquides inflammables ou combustibles, telle l’essence, et ne pas utiliser à proximité.

* Eviter d’aspirer des objets durs ou pointus.

* Ne pas modifier les systèmes électriques, mécaniques ou thermiques.

* Remplacer le cable far un cable identique fourni far Advance.

CONSERVER CES INSTRUCTIONS

3 - FORM NO. 56041453 / CARPETWIN 14 / 18

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Deben aplicarse ciertas precauciones básicas siempre que se utilice un aparato eléctrico, incluyendo las siguientes:

Lea todas las instrucciones antes de utilizar la máquina.

Esta máquina también es adecuada para el uso profesional, por ejemplo, en hóteles, colegios, hospitales, fábricas, tiendas y oficinas, que no sean los usos domésticos normales.

¡ESTE APARATO HA SIDO DISEÑADO ÚNICAMENTE PARA SU USO EN SECO!

¡NO UTILICE LA MÁQUINA EN SUELOS O MOQUETAS HÚMEDOS!

¡AVISO !

Para reducir el riesgo de incendio, descarga eléctrica o lesión:

* No deje la máquina conectada a la red. Desenchufe la máquina cuando no se está utilizando y antes de efectuar una revisión.

¡AVISO !

Para reducir el riesgo de una descarga eléctrica, no utilice la máquina al aire libre, ni en superficies húmedas o mojadas.

* No deje que se utilice la máquina como juguete. Debe prestarse una atención especial cuando la maneja o se utiliza cerca de los niños.

* Siga escrupulosamente las indicaciones de este manual. Utilice únicamente piezas recomendadas por el fabricante.

* No utilice la máquina con el cable o clavija en estado defectuoso. Si el aparato no funciona correctamente, si ha sufrido una caída o daños, si se ha dejado a la intemperie, o si ha sufrido una inmersión en agua, devuélvalo a un Centro de Servicio. No utilice la máquina si el cable eléctrico muestra cualquier signo de daño. Inspeccione regularmente el cable por si presente algún daño, especialmente cuando haya sido aplastado, cogido por una puerta o pisado por un objeto pesado.

* No arrastre o transporte la máquina por el cable. No utilice el cable para dirigir la máquina. Mantenga el cable alejado de bordes y esquinas que lo podrían dañar. Así mismo, mantenga el cable alejado de fuentes de calor.

* No desenchufe la máquina tirando del cable. Para desenchufar, tire de la clavija, no del cable.

* No toque la clavija, el cable o la máquina con las manos húmedas o mojadas.

* No inserte ningún objeto en las aberturas. No utilice la máquina con ninguna abertura obstruida.

* Mantenga alejado de las aberturas y piezas en movimiento las prendas sueltas, el pelo, los dedos y todas las demás partes del cuerpo.

* No aspire ningún tipo de objeto que esté ardiendo o que desprenda humo, como cigarrillos o cerillas. Bajo ninguna circunstancia la máquina podrá ser usada para aspirar materiales calientes. En particular no utilice la máquina para limpiar chimeneas, hornos o similares con cenizas calientes o incandescentes.

* No utilice la máquina sin tener colocados los filtros y/o la bolsa del polvo.

* Apague todos los controles antes de desenchufar la máquina. La clavija siempre debe ser desenchufada de la red eléctrica antes de revisar o reparar la máquina o el cable de conexión eléctrica.

* No aspire objetos duros o afilados.

* Tenga un cuidado especial cuando aspirar las escaleras.

* No utilice la máquina para recoger combustible, materiales nocivos para la salud o materiales explosivos como la gasolina, tampoco debe utilizarse en atmósferas explosivas. No utilice la máquina para aspirar agua u otros líquidos o para aspirar polvo peligroso, contaminante o tóxico.

* No realice ningún tipo de intervención o modificación en los dispositivos mecánicos, eléctricos o de seguridad térmica de la máquina.

* Cuando repare o sustituya el cable de conexión eléctrica, utilice el mismo tipo de cable suministrado originalmente con la máquina. Este cable le puede ser suministrado por ADVANCE.

NO PIERDA ESTAS INSTRUCCIONES

FORM NO. 56041453 / CARPETWIN 14 / 18 - 4

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should electrically malfunction, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER!

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance.

If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated in Figures 2 and 3 may be used to connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a qualified electrician.

The green-colored rigid ear, tab, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. Grounding adapters are not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

The Green (or Green/Yellow) wire in the cord is the grounding wire. When replacing a plug, this wire must be attached to the grounding pin only.

Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs and outlets. DO NOT use extension cords more than 50 feet (15 m) long.

PLEASE NOTE: FOR NORTH AMERICA ONLY

INSTRUCTIONS VISANT LA MISE À LA TERRE

Cet appareil doit être mis à la terre. En cas de défaillance ou de panne éventuelles, la mise a la terre fournit au courant un chemin de moindre résistance qui réduit le risque de choc électrique. Cet appareil est pourvu d’un cordon muni d’un conducteur de terre et d’une fiche avec broche de terre. La fiche doit être branchée dans une prise appropriee correctement installée et mise à la terre conformément aux règlements et ordonnances municipaux.

AVERTISSEMENT !

Un conducteur de terre mal raccordé peut entraîner un risque de choc électrique. Consulter un électricien ou un technicien d’entretien qualifié si vous n’êtes pas certain que la prise est correctement mise à la terre. Ne pas modifier la fiche fournie avec l’appareil - si elle ne peut être insérée dans la prise, faire installer une prise adéquate par un électricien qualifié.

Cet appareil est destiné à un circuit de 120 V et est muni d’une fiche de terre semblable à celle illustrée par le croquis 1. Un adaptateur temporaire semblable à celui illustré par le croquis 2 et C peut être utilisé pour brancher cette fiche à une prise bipolaire comme l’illustre le croquis 2 si une prise avec mise à la terre n’est pas disponible. L’adaptateur temporaire devrait etre utilisé seulement jusqu’à ce qu’une prise avec mise à la terre soit installée par un électricien qualifié. L’oreille rigide ou le crochet ou autre dispositif semblable, de couleur verte, prolongeant l’adaptateur doit

Iêtre raccordé à un élément correctement mis à la terre comme le couvercle d’une boîte de sortie mise à la terre. L’adaptateur doit être fixé par une vis métallique. Note: Au Canada, I’utilisation d’un adaptateur temporaire n’est pas autorisée par le Code canadien de l’électricité.

Remplacez la prise si la prise de terre est abîmée ou cassée.

Le fil Vert (ou Vert/Jaune) dans la ganse est le fil de terre. Lors du remplacement d´une prise, ce fil doit être raccordé à la prise de terre uniquement.

Les ralonges connectées à cette machine doivent avoir 12 mesures, trois ganses de fil ayant trois fiches masculines féminines tree-prong plugs

and outlets. N´UTILISEZ PAS de ralonge de plus de 15 m (50 pieds) de long.

VEUILLEZ NOTER: CES INSTRUCTIONS CONCERNENT UNIQUEMENT L’AMÉRIQUE DU NORD

5 - FORM NO. 56041453 / CARPETWIN 14 / 18

INTRUCCIONES PARA HACER LA TOMA A TIERRA

Este aparato deberá ser conectado a tierra. En caso de malfuncionamiento o de desperfectos, la toma a tierra proporciona una vía de menor resistencia de la corriente eléctrica para reducir el riesgo de choques eléctricos. Esta unidad viene equipada con un cordón con conductores para toma a tierra y con un enchufe con toma a tierra. Ese enchufe deberá ser enchufado a un receptáculo en buen estado con instalación a tierra según los códigos y ordenanzas de la zona.

¡PELIGRO !

Si el conductor a tierra no está instalado correctamente pueden producirse riegos de choques eléctricos. En caso de duda, consulte con un electricista o personal de servicio autorizados. No modifique el cordón provisto con el aparato. Si no calza en el receptáculo, llame a un electricista calificado para que coloque un receptáculo adecuado.

Este aparato se usa con un circuito de 120-voltios nominales, y tiene un enchufe con toma a tierra tal como se muestra en la figura 1, a continuación.

Se puede usar un adaptador provisorio tal como se ve en las figuras 2 y 3 en caso de disponerse de un receptáculo sin toma a tierra como en la figura 2. Dicho adaptador provisorio se usará solamente hasta que un electricista calificado instale un receptáculo con la toma a tierra correspondondiente (figura 1). La lengüeta de conexión de color verde que sale del adaptador deberá ser conectada a una toma a tierra permanente como, por ejemplo, la caja del receptáculo con toma a tierra. Siempre que se use el adaptador, hay que sostenerlo en su lugar con un tornillo de metal.

Sustituya el enchufe si la patilla de tierra está dañada o rota.

El hilo verde (o verde/amarillo) del cordón es el hilo de tierra. Cuando sustituya el enchufe, este hilo sólo debe ir conectado a la patilla de tierra.

Los cables alargadores conectados a esta máquina deben ser del calibre 12, trifilares, con tres patillas y tomas de pared adecuadas. NO UTILICE cables alargadores de más de 15 m.

ATENCIÓN : PARA AMÉRICA DE NORTE SOLAMENTE.

FORM NO. 56041453 / CARPETWIN 14 / 18 - 6

INTRODUCTION

This manual will help you get the most from your Advance Carpetwin.

Read it thoroughly before operating the machine.

Note: Bold numbers in parentheses indicate an item illustrated on page 1.

This product is intended for commercial use only.

PARTS AND SERVICE

Repairs, when required, should be performed by your Authorized Advance Service Center, who employs factory trained service personnel, and maintains an inventory of Advance original replacement parts and accessories.

Call the ADVANCE DEALER named below for repair parts or service.

Please specify the Model and Serial Number when discussing your machine.

(Dealer, affix service sticker here.)

NAME PLATE

The Model Number and Serial Number of your machine are shown on the

Nameplate on the machine. This information is needed when ordering repair parts for the machine. Use the space below to note the Model

Number and Serial Number of your machine for future reference.

A-KNOW YOUR MACHINE

As you read this manual, you will occasionally run across a bold number in parentheses - example: (2). These numbers refer to an item shown on this page. Refer back to this page whenever necessary, to pinpoint the location of an item mentioned in the text.

1 Handle

2 Cord Hook

3 Vacuum Hose

4 Handle Lock Button

5 Bag Housing

6 Carrying Handle

7 Red Light

8 Green Light

9 Brush Housing

10 Brush Height Adjustment Knob

11 Pedal

12 Power Cord

13 Wand

14 Crevice Tool

15 “Bag Full” Light

16 Bag Housing Latch

17 Main Power Switch

18 Exhaust Filter Cover

19 Filter Cover Latch

20 Power Cord Clamp (Figure B)

21 Locking Latch (Figure B)

22 Dusting Brush

MODEL NUMBER

SERIAL NUMBER

UNCRATE THE MACHINE

When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected. Contact the Advance Customer Service

Department immediately to file a freight damage claim.

B-SET UP AND ASSEMBLY

1 Carefully remove the machine from its carton.

2 Push the Handle (1) into the opening at the top of the Bag Housing

(5) until the button snaps into the hole between the Switch (17) and the Bag Full Light (15).

3 Install the Bag Housing (5) on the Brush Housing (9). Slide the

Locking Latch (21) to the left.

4 Measure 15 inches of Power Cord (12) from where it comes out of the machine. Insert the cord at this point into the Power Cord Clamp

(20).

5 Insert one end of the Vacuum Hose (3) into the top of the vacuum body and the other end into the extension wand. Insert the wand into the hole on the right side of the vacuum body and clip onto the right side of the machine. Snap the Hose (3) into the clip below the

Handle (1).

6 To install a Paper Dust Bag, push the Bag Housing Latch (16) and remove the back cover. Then follow the instructions printed on the

Paper Dust Bag. Never operate the machine without a Dust Bag in place.

7 - FORM NO. 56041453 / CARPETWIN 14 / 18

OPERATING THE MACHINE

1 To release the Power Cord (12) from the Cord Hooks (2), press the

Handle Lock Button (4) in while pushing down on the Handle (1) and pull the power cord off the hooks. Plug the Power Cord into a properly grounded electrical outlet.

2 Turn the Main Power Switch (17) ON. “l” is ON and “O” is OFF.

3 Step on the Pedal (11) and tilt the handle back. The Green Light (8) on the base will come on to indicate that the brush motor is running.

C - IMPORTANT !

Foot pedal must be used to release base to operating position.

Failure to do so could result in damage to the handle release mechanism.

4 Turn the Height Adjustment Knob (10) to adjust the height of the brush. If the Red Light (7) comes on, slowly turn the Knob in the opposite direction until the light goes off.

If the red light stays on continuously, there may be debris wrapped around the brush. This can cause the overload protector for the brush motor to trip. If this occurs, turn the Main Switch OFF and unplug the power cord. Remove any debris from the brush and turn the Main Switch back ON. This will automatically reset the overload protector. The machine can also be reset by locking the handle in the upright position. Remove any debris from the brush and repeat

Step 3. If the overload protector trips repeatedly, or if the red light stays on continuously, contact Advance for service.

5 Change the bag whenever the “Bag Full” Light (15) comes on.

If the light comes on before the bag is full, the inside of the bag may be coated with very fine dust (change the bag), or debris may be built up somewhere between the brush and the bag.

USING THE WAND

To use the Wand (13), put the Handle in the upright locked position. The brush motor will stop automatically. Slide the Wand out of its holder.

Install the Crevice Tool (14) or Dusting Brush (22) on the end of the

Wand, if desired.

AFTER USING THE MACHINE

1 Unplug the Power Cord from the electrical outlet and wrap it around the Cord Hooks on the front of the machine.

2 Check to see if the bag is full, replace if necessary. Clean the bag housing, if necessary.

3 Clean or replace the Vacuum Inlet Filter every third time the bag is changed. Clean or replace the Electrostat Exhaust Filter every fifth time the bag is changed.

4 Remove any built-up carpet fibers or debris from the brush housing.

5 Store the machine indoors in a clean, dry place.

VACUUM MOTOR BRUSHES

Have your Advance Dealer check the carbon motor brushes once a year or after 500 operating hours.

IMPORTANT !

Motor damage resulting from failure to service the carbon brushes is not covered under warranty. See the Limited Warranty Statement.

MAINTENANCE

CAUTION !

Always disconnect the Power Cord before performing any machine maintenance.

CHANGING THE PAPER DUST BAG

Change the Bag whenever the “Bag Full” Light comes on. To replace the

Paper Dust Bag :

1 Push the Bag Housing Latch (16) in and remove the back cover.

2 Remove the Paper Dust Bag following the instructions printed on the bag.

3 Install a new Paper Dust Bag following the instructions printed on the bag.

IMPORTANT !

Never operate the machine without a Dust Bag in place.

CHANGING THE CLOTH DUST BAG

Empty the Bag whenever the “Bag Full” Light comes on. To empty the

Cloth Dust Bag :

1 Push the Bag Housing Latch (16) in and remove the back cover.

2 Remove the Cloth Dust Bag following the instructions printed on the bag.

3 Remove bag clip and shake out bag contents.

4 Put the bag clip back on the bag.

5 Install the Cloth Dust Bag following the instructions printed on the bag.

6 Replace the Electrostat Exhaust Filter every fifth time the bag is changed (more often in very dusty applications).

IMPORTANT !

Never operate the machine without a Dust Bag in place.

FORM NO. 56041453 / CARPETWIN 14 / 18 - 8

CLEANING THE VACUUM INLET FILTER

The vacuum inlet filter catches any dirt spilled from the bag, before it can enter the vacuum motor. The filter is located just below the bag. Clean the filter every third time that the bag is changed (more often in very dusty applications). To clean the Vacuum Inlet Filter...

1 Push the Bag Housing Latch (16) in and remove the back cover.

2 Slide the Filter Holder out of the bottom of the Bag Housing.

3 Remove the filter and wash it in warm water. Let the filter dry completely before putting it back into the machine.

IMPORTANT !

Never operate the machine without the Vacuum Inlet Filter in place.

CHANGING THE BRUSH

1 Lay the machine over onto its left side.

2 Slide the side cover (item #46 / page 13) off of the brush housing.

3 Carefully pry the roller support (item #40 / page 13) off the end of the brush (reuse on new brush).

4 Grasp the center of the brush by the bristles and pull it up and out the right side of the housing.

5 Slide brush end with hex opening into housing first, make sure it slides all the way down onto transmission support (item #34 / page

13).

6 Follow steps 1-3 in reverse order to reassemble.

D-CHANGING THE ELECTROSTAT EXHAUST FILTER

The electrostat exhaust filter catches any dirt that may escape from the dust bag, vacuum inlet filter, or lower motor filter. The electrostat exhaust filter is located just below the carrying handle. Replace the filter every fifth time that the dust bag is changed (more often in very dusty applications).

To replace the Electrostat Exhaust Filter...

1 Push the Filter Cover Latch (19) in and remove the Electrostat

Exhaust Filter Cover (18).

2 Remove the Filter from the filter holder and insert a new filter in its place.

3 Snap the Filter Cover back into place.

IMPORTANT !

Never operate the machine without the Electrostat Exhaust Filter in place.

REPLACING THE BELT

WARNING !

To reduce the risk of electric shock, unplug before servicing.

1 Remove screws (7 on Carpetwin 14 / 9 on Carpetwin 18) from the top cover (item #2 / page 13) and remove top cover from the brush housing.

2 Remove both screws in transmission support (item #34 / page 13).

3 Lift the end of the brush up and remove the belt from the brush pulley.

4 Bend brush housing out just enough to slide the belt off of the motor pulley (be careful not to break housing!).

5 Reassemble in reverse order.

TECHNICAL SPECIFICATIONS (as installed and tested on the unit)

Model

Voltage

Rated Power

Protection Class (electrical)

Sound Pressure Level

Total Weight

Vibrations at the Hand Controls

V/Hz

W dB(A)/20

µ

Pa lbs / kg m/s 2

Carpetwin 14

120/60

900

69

19.5 / 8.8

<2.5m/s 2

Carpetwin 18

120/60

920

69

20.5 / 9.3

<2.5m/s 2

9 - FORM NO. 56041453 / CARPETWIN 14 / 18

NOTES

FORM NO. 56041453 / CARPETWIN 14 / 18 - 10

11 - FORM NO. 56041453 / CARPETWIN 14 / 18

Item Ref. No.

Qty Description

BAG HOUSING

Item Ref. No.

Qty Description

56704209

56704221

56646869

56704210

56703795

56703662

56703977

56704159

56646875

56703708

56646877

56646878

56704211

56646879

56646880

56703706

56703705

56703972

56646884

56646885

56704205

56646851

56703712

56703714

56703713

56703720

56704206

56703785

56646858

56704207

56703779

56646861

56703978

56704216

56703725

56704208

56646865

36

37

38

39

40

29

31

32

33

34

24

25

26

27

28

18

19

21

22

23

13

14

15

16

17

10

11

8

9

12

5

6

3

4

7

1

2

1 Bag Housing Cover

1 Grill Complete

1 Grill Filter Holder

1 Scented Pad (pkg of 10)

1 Internal Filter

1 Bag Entrance

1 Electrical System Assembly (3 wires)

1 Round Dusting Brush

1 Round Dusting Brush Support

1 Bag Housing

1 Valve Kit

1 Valve Filter

1 O-Ring

1 SemiFlex Hose W/Sleeves

1 Crevice Tool

1 Upper Hook for Flex Tube

1 Handle Grip

1 Retainer

1 Chromate Tube

1 Handle Tube Assy

1 Handle Cover

1 Cord, 3 x 18

1 Strain Relief

1 Cord Clamp

1 Vacuum Sensor

1 Button (w/support & spring)

1 Main Switch

1 Indicator Light

1 Cord Hook

1 Frame Handle Assy

1 Contact Housing

1 Contact Cover

1 Foam Filter

1 Gasket

1 Terminal Block

1 Foam Motor Filter

1 Gasket

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

66

**

**

**

**

**

**

*

56704212

56704222

56646888

56704223

56704224

56703966

56703938

56646893

56704225

56646895

56646896

56646897

56646898

56704215

56646900

56646901

56704237

56704238

56703775

56704213

56704214

56704226

56703990

56703768

56703769

56320676

56703774

56703771

56703772

** = Optional

* = Not Shown

NOTE 1: 56704168 used prior to SN1498331 on 14” & prior to SN1499231 on 18”

1

1

1 Exhaust Filter (pkg of 5)

1 Exhaust Filter Cover

1 Complete Grill

1 Blocking Joint Pin

1

1 Control Pin Slide

1 Vacuum Motor Housing

1 Lower Curve

1 Curve Support

1

1 O-Ring

1 Inner Vacuum Motor Housing

1 Hose Inlet

1 Cord Clamp

1

2

1

1

1

1

1

Bag Door Latch (w/spring)

Filter Holder

Joint Pin

Upper Curve

Vacuum Motor NOTE 1

Carbon Brush for 56704237 & 56704168

TSBUS2002-829

Foam Filter

Telescopic Wand

Wand Clip

Vacuum Sensor Adapter

Cord Clip

A/R Bag, Paper (pkg of 10)

A/R Cloth Bag W/Clip

A/R Clip, Cloth Bag

A/R Upholstery Tool

A/R Extension Tube, 30mm x 30cm

A/R Tube Bend W/Suction Control revised 11/02 FORM NO. 56041453 / CARPETWIN 14 / 18 - 12

10

2

52

16

49

57

19

15

8

9

46

7

49

23

4

12

26

24

49

53

21

23

33

6

5

20

13

11 14

56

3

25

32

41

28

51

48

27

39

50

28

42

34

22

43

44

39

54

1

45

57

18

35

31

29

36

37

30

40

55

38

17

18

49

13 - FORM NO. 56041453 / CARPETWIN 14 / 18

47

Item Ref. No.

Qty Description

BRUSH HOUSING - 14 / 18

Item Ref. No.

Qty Description

1

2

15

16

17

18

19

10

11

12

13

14

7

8

5

6

9

3

4

25

26

27

20

21

22

23

24

28

29

30

*

56704107

56704022

56704023

56704024

56703738

56703762

56703008

56704028

56703757

56704030

56704031

56704032

56704033

56704065

56704106

56704035

56704124

56703743

56704037

56704137

56704038

56704130

56704129

56704203

56704204

56704227

56704228

56704229

56704230

56704148

56704016

56704017

56704018

56703766

56704019

56704020

1 Brush Housing Assembly, 14"

1 Brush Housing Assembly, 18"

1 Body Main Brush Head, 14"

1 Body Main Brush Head, 18"

1 Electric Brush Cover, 14"

1 Electric Brush Cover, 18"

1 Joint Complete w/pin slide (#4)

1 Joint Pin Slide

1 Support Right Joint w/felt seal

2 Plunger

2 Spring, Handle Release Pedal

1 Double Pin Washer

1 Double Release Plate

1 Handle Release Pedal

1 Support Left Joint w/felt seal

1 Switch Activator Pin

1 Spring

1 Brush Motor Switch

1 Brush Adjuster

1 Brush Adjuster Knob

1 Front Axle

2 Front Wheel

1 Spring, Brush Adjust

1 Rear Axle

2 Rear Wheel

2 Wheel Retainer

4 Screw, 2.9 x 16mm

1 Filter Grill

1 Brush Motor Filter

1 Stop Grill Plate

1 Brush Motor, 14"

1 Brush Motor, 18"

2 Carbon Brush for 56703743 & 56704037

1 Brush Motor Support Kit

1 Pulley Spacer

1 Pulley

* = Not Shown

56704105

56704058

56704059

56704060

56704046

56704067

56704045

56704217

56704218

56704140

56704141

56704135

56704131

56704231

56703853

56704042

56704155

56704044

56703747

56703746

56704039

56704047

56704041

56704049

56704050

56704051

56704052

56704053

56704054

56704055

56704056

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

31

32

33

34

35

36

37

38

39

40

41

42

1 Pulley Nut

1 Circuit Board

1 Channel Cover

1 Transmission Support

1 Brush Pulley

1 Brush Pulley Nut

1 Timing Belt

1 Wheels Support

4 Screw, 3.9 x 16mm

1 Roller Support

1 Side Lever

1 Front Bumper Gasket, 14"

1 Front Bumper Gasket, 18"

1 Back Bumper Gasket, 14"

1 Back Bumper Gasket, 18"

5 Screw, 4.8 x 50mm (qty of 6 on 18")

2 Screw, 3.5 x 38mm (qty of 3 on 18")

1 Side Cover

1 Brush Roller, 14"

1 Brush Roller, 18"

1 Brush Motor Filter

5 Screw, 3.9 x 13mm

2 Screw, 3.5 x 22mm

1 Screw, 2.2 x 16mm

1 Lens Set, Red / Green

1 Felt for brush housing

1 Shoe Kit, 14"

1 Shoe Kit, 18"

1 O-Ring

1 Male Electrical Connection Set

3 Washer

FORM NO. 56041453 / CARPETWIN 14 / 18 - 14

2

3

120Vac

Brush

Motor

7

Vac

Motor

4

5

6

1

Item

5

6

7

3

4

1

2

*

*

WIRING DIAGRAM

Ref. No.

Qty Description

56703708

56704159

56646877

56704237

56704238

56703738

56704042

56703743

56704037

56704137

1 Main Switch

1 Vacuum Sensor

1 Indicator Light

1 Vacuum Motor (56704168 used prior to SN1498331 on 14” & SN1499231 on 18”)

2 Carbon Brush for 56704237 & 56704168 TSBUS2002-829

1 Brush Motor Switch

1 Circuit Board

1 Brush Motor, 14"

1 Brush Motor, 18"

2 Carbon Brush for 56703743 & 56704037

15 - FORM NO. 56041453 / CARPETWIN 14 / 18

revised 11/02

Carpetwin 14 / 18 TWO YEAR LIMITED WARRANTY

FOR MODELS 56704200 & 56704201 ONLY

Nilfisk-Advance, Inc. warrants each new Carpetwin 14 / 18 carpet vacuum against defects in material and workmanship under normal use and service.

The obligation under this warranty is limited to repair or replace at our factory or authorized distributor service station any part or parts thereof which within the warranty period are returned to our factory or authorized distributor service station, transportation prepaid, after examination discloses it to have been thus defective.

The warranty period during which basic coverage applies is Two (2) years for parts replacement and one year for service labor. The start date of the warranty coverage shall be the purchase date by the original end user, or six months from the date the machine was shipped from the factory, which ever is earlier. The Warranty Registration Card is to be completed and returned immediately at the time of purchase.

This warranty shall not apply to: (1) accidents and misuse, (2) damage in transit, (3) overloading the capacity of the machine, (4) failure due to lack of proper maintenance or care as described in the operating and maintenance instructions, (5) relatively minor adjustments such as tightening of screws or bolts, etc., not connected with the replacement of parts, (6) repairs or alterations by an organization other than the factory or an authorized

Nilfisk-Advance Service Center.

STATED WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. Any statutory implied warranties, including any warranty of merchantability or fitness for a particular purpose, are expressly limited to the durations of this written warranty. Nilfisk-Advance will not be liable for any other damages arising out of or in connection with the furnishing, performance, use of or inability to use the machine. This remedy shall be the exclusive remedy of the Buyer.

Authorized Nilfisk-Advance Service Centers can assist owners in the proper handling of any warranty question or claim. In the event that you want to contact Nilfisk-Advance directly, please write to the Customer Service Department at Nilfisk-Advance, Inc., 14600 21st Avenue North, Plymouth,

Minnesota 55447-3408. Provide an explanation of the problem and include the serial number of the machine as well as the name of the selling organization. The Customer Service Department will investigate and then contact you.

Cut out and mail to:

Nilfisk-Advance, Inc.

14600 21st Avenue North

Plymouth, Minnesota 55447-3408

✂

IMPORTANT: This card contains information necessary to expedite warranty protection.

Mail within 30 days of purchase to Nilfisk-Advance.

LIMITED WARRANTY

PLEASE PRINT

Purchaser ________________________________________________

Address _________________________________________________

City _______________________ State ___________ Zip _________

Model ______________ Serial Number ________________________

Purchased from ___________________________________________

City _______________________ State __________ Zip __________

Date Purchased ___________________________________________

THIS IS TO CERTIFY THAT THE ABOVE EQUIPMENT

WAS CHECKED OUT IN WORKING CONDITION.