Under Seat Storage

Under Seat Storage
TOYOTA
TUNDRA
2007 -
UNDER SEAT STORAGE TRAY
Preparation
NOTE: Part number of this accessory may not be
the same as the part number shown.
Vehicle Service Parts (may be required for reassembly)
Part Number: PT871-34070
Kit Contents
Item #
1
2
3
Quantity Reqd.
1
1
1
Item #
1
2
3
Description
Under Seat Storage Tray
Hardware Bag
Instruction Sheet
Hardware Bag Contents
Item #
1
2
3
Quantity Reqd.
4
4
Quantity Reqd.
Description
Screw Retainer Clip
Knobs
Description
Conflicts
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
JBL Audio and Navigation
Recommended Tools
Personal & Vehicle
Protection
Notes
Floor protection
Special Tools
Notes
Installation Tools
Notes
Special Chemicals
Notes
General Applicability
C-Cab only
Recommended Sequence of Application
Item #
1
2
3
Accessory
*Mandatory
Issue: A
10/02/06
Description
Legend
Additional Items Required For Installation
Item #
1
2
3
Quantity Reqd.
Page 1 of 3 pages
TOYOTA
TUNDRA
2007 -
UNDER SEAT STORAGE TRAY
Procedure
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
1. Preparation.
(a) Open rear doors.
(b) Raise rear seat cushions. Pull on lever to
release. (Fig. 1-1)
Fig. 1-1
(c) Apply floor protection. (Fig. 1-2)
Fig. 1-2
(d) Open carton and inspect kit for content
and Remove the (2) covers. (Fig. 1-3)
2. Install the Under Seat Tray.
Fig. 1-3
(a) On the seat brackets, press (1) screw
retainer clip into each of the (4) holes
indicated. 2 per side, driver side shown.
(Figs. 2-1 & 2-2)
(1) Orientation of the clip is not critical.
Fig. 2-2
Fig. 2-1
(b) Place the Under Seat Tray onto the seat
brackets as shown. (Fig. 2-3)
(c) Install (1) knob into each of the (4)
previously installed screw retainer clips.
2 per side, driver side shown. (Fig. 2-4)
Fig. 2-3
(1) Tighten hand tight.
Fig. 2-4
3. Post Installation
(a) Replace and lock the lids. (Fig. 2-5)
(b) Lower the seat cushions. Pull on lever to
release. (Fig. 2-6)
Fig. 2-5
(c) Remove vehicle protection.
Fig. 2-6
(d) Close rear doors.
Issue: A
10/02/06
Page 2 of 3 pages
TOYOTA
TUNDRA
2007 -
UNDER SEAT STORAGE TRAY
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Accessory Function Checks
Locked lid
Lids lock
Vehicle Function Checks
Ensure the seat cushions fully lock in the
down position.
Issue: A
10/02/06
Page 3 of 3 pages
Lift seat cushion to verify locking function.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement