STATII DEDURIZARE NOBEL AS

STATII DEDURIZARE NOBEL AS

ELECTRONIC PROGRAMMER SV TYPE
FOR AUTOMATIC SOFTENERS
SERIES: AC/SV
AS/SV
CAUTION !
Switch off the power supply and remove the electrical wiring before to open or any
operation inside the programmer.
CALOR SRL Str. Progresul nr. 30-40, sect. 5, Bucuresti
tel: 021.411.44.44, fax: 021.411.36.14
www.calorserv.ro - [email protected]
ELECTRONIC PROGRAMMER SV
1.
General information
1.1.
•
•
•
•
How to store, delivery and instal
closed rooms
open space
transport
installation
1.2.
t = ºF
humidity rel.
0÷45
0÷45
0÷45
0÷45
32÷113
32÷113
32÷113
32÷113
5÷95% without condensate
5÷95% without condensate
5÷95% without condensate
5÷95% without condensate
notes
protect from sun-light and rain
protect from sun-light and rain
protect from sun-light and rain
Technical characteristics
Electrical supply
Protection
2.
t = ºC
V ph/Hz W 230 1/50-60 10
IP20
Electrical wiring connection
• insert the power feeder of the programmer in a proper electrical socket; check the
power supply meets the technical data.
3.
Commissioning
• The programmer is usually supplied already fixed to the control valve of the softener,
held by the special rear brackets and screwed on the front of the programmer.
• Flow sensor (connected with programmer) is usually plugged in the proper socket on
the body valve, linked to the internal turbine; if it were not so, provide to plug it in just
by hand, with no tools.

CALOR SRL Str. Progresul nr. 30-40, sect. 5, Bucuresti
tel: 021.411.44.44, fax: 021.411.36.14
www.calorserv.ro - [email protected]
ELECTRONIC PROGRAMMER SV
4.
Description
The programmer works at 12 V ac (10 VA) power and it is normally supplied complete of
built-in transformer in order to be connected directly to the main supply (230 V 50/60 Hz).
The programmer keeps in memory permanently all last entered data, even when the
power supply is off.
The purpose of the battery included in the electronic card is only to keep in memory the
temporary data (current time of day, supplied volume of water, time of phases of the running
regeneration), in case of power failure. A new buffer battery can keep the memory for approx
one month; its efficiency decreases in the time, when it is aged.
The display shows normally current time of day.
During the regeneration cycle, the display shows, alternately :
•
•
the time of rotation of the motor (seconds counting-down) during the passage between two
following phases
the time of the single phase of the regeneration cycle (minutes counting-down) : 1C
BACKWASH = 2C BRINE DRAWING = 3C SLOW RINSE = 4C FAST RINSE
Close to the left of the button "TIME OF DAY" is available a HIDDEN button (see the first
page of this manual); it is useful for programming as described in the sequel.
The button "MANUAL REGEN", simulates an end-cycle, then it starts the regeneration.
CAUTION • The pushing of the button "MANUAL REGEN", while a regeneration is
running already, concludes the running phase and skips the system to the
following one.
Note: All buttons must be pressed for a time from 0.6 and 1.2 seconds.
4.1.
Memory re-set
Remove the frontal panel (fixed with 4 screws at the corners), to access to the
electronic card. Besides the 4 main (protruding) buttons already mentioned, another
button (flat) is available, on the right and lower side of the card. By pushing this button
the memory is totally re-set.
4.2.
End-cycle
The SV programmer allows to handle the operating cycle according to both time and
volume. The volume of water supplied is measured by mean of a pulse sender (turbine)
integrated in the body of the automatic valve (S132/SV type).
The end cycle is scheduled as follows :
• regeneration starts after that the pre-set volume of water has been supplied, but only
at a pre-set time of day
• regeneration starts at a pre-set day and time of day, adjustable in a range of 14 days
and 24 hours per day (max. 1 regeneration per day). The regeneration starts also if
the pre-set volume has not been reached.
Since it is not possible to exclude time programming, the end cycle (and then the
regeneration) will start at least every 14 days (minimum allowed set).

CALOR SRL Str. Progresul nr. 30-40, sect. 5, Bucuresti
tel: 021.411.44.44, fax: 021.411.36.14
www.calorserv.ro - [email protected]
ELECTRONIC PROGRAMMER SV
4.3.
Volume visualization, ratio reader/water meter
The integrated pulse sender turbine sends 14 pulses for liter of water supplied.
The pulses are received by the programmer, that drives the same pulses according to a
programmed ratio (ratio reader/water meter).
The driven pulses are shown on the display as single units, the real meaning (value) of
which depends on the programmed ratio.
Hence, if value 14 is programmed as ratio, the programmer will increase one unit after
that received 14 pulses, therefore every liter. It means that the value the display shows
are liters.
Since four digits are available on the display, the max. allowable visualization is 9999
liters.
To dispose of bigger settings it will be necessary to increase the value of the programmed
ratio (ratio reader/water meter); in this way it is possible to count and visualize multiple of
liters.
For instance if the value 28 is programmed as ratio, the programmer will increase one
unit after that received 28 pulses, therefore every 2 liters. It means the value of the
display shows are double liters (with maximum 19998 liters).
To program the ratio reader/water meter see chapter "Programming”.
4.4.
Volume of end-cycle
The programmer allows to set the volume of end-cycle and a "reserve volume" as well.
The meaning of the "reserve volume" is that the programmer subtracts this value from the
volume of end-cycle and the results is the volume scheduled in order to start regeneration.
(Example of settings: volume = m³ 5; reserve volume = m³ 1; the programmer will start the
regeneration when the system has supplied 4 m³ of treated water (5-1=4)).
According to the above explanations, it is obvious that this feature can be significative
only if the time-volume schedule is selected.
Indeed, according to this mode, regeneration will start only at the pre-set time of day and
only AFTER that the pre-set volume of water has been already supplied.
However, after these information, and in order to make easier the programming and
handling of the unit, it is suggested NOT to program the reserve volume but only the volume
of end cycle. The programmed value could be lower than the real cycle of the softener in
order to make, automatically, the same feature of the volume reserve.
To program the regeneration volume see chapter "Programming”.

CALOR SRL Str. Progresul nr. 30-40, sect. 5, Bucuresti
tel: 021.411.44.44, fax: 021.411.36.14
www.calorserv.ro - [email protected]
ELECTRONIC PROGRAMMER SV
5.
Programming
5.1.
How to set the time of day
• Push the button "TIME OF DAY", and then "ADVANCE" to modify the blinking digits
• First pressing allows to modify the minutes, the second one to modify hours
• Push once again "TIME OF DAY" to show the adjusted time of day
5.2.
How to set the time and day of regeneration and volume data
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Push once the “HIDDEN” button; the light dot is shown between the 1st and 2nd
digit of the display
By pushing now the button “ADVANCE”, it is allowed to adjust the blinking
numbers (two digits on the right side, minutes)
Push once again the “HIDDEN” button to skip to the adjustment of the blinking
numbers on the left side, hours; the light dot still remains between the 1st and
2nd digit; use the button “ADVANCE” to modify the blinking digits.
Push again the “HIDDEN” button; the light dot appears between the 2nd and 3rd
digit; the display shows notice “FF04”, where the number 04 (or any other,
between 1 and 14) indicates how often regeneration is scheduled.
By pushing the button "ADVANCE" the blinking digits (only numbers) can be
modified; the allowable setting is between 1 and 14 (every day - every 14 days).
Push again the “HIDDEN” button; the light dot is shown between the 3rd and 4th
digits of the display, allowing to adjust the volume of regeneration.
By pushing the button "ADVANCE" the blinking digits (3rd and 4th) can be
modified
Push once again the “HIDDEN” button to skip to the adjustment of the blinking
numbers on the left side; the light dot still remains between the 3st and 4th digit;
use the button “ADVANCE” to modify the blinking digits.
Push once again the “HIDDEN” button; the light dot is shown on the right side of
the 4th digit, allowing to adjust the reserve volume of regeneration
By pushing the button "ADVANCE" the blinking digits (3rd and 4th) can be
modified
Push once again the “HIDDEN” button to skip to the adjustment of the blinking
numbers on the left side; the light dot still remains at right side of the 4th digit;
use the button “ADVANCE” to modify the blinking digits.
Push again the “HIDDEN” button; the display shows notice “AA14”, where the
number 14 (or any other, between 1 and 14) indicates the pre-set ratio readerwater meter.
By pushing the button "ADVANCE" the blinking digits can be modified
Push again the “HIDDEN” button; the display shows notice “End-”, indicating the
end of programming and saving in memory of entered data.
After approx 1 second the notice disappears and the display show again the
current time of day.
WARNING: whether not any button is pushed for 30” before to reach the
visualization of notice “End-“ the programming mode is interrupted
AND ALL MODIFICATIONS ARE LOST.

CALOR SRL Str. Progresul nr. 30-40, sect. 5, Bucuresti
tel: 021.411.44.44, fax: 021.411.36.14
www.calorserv.ro - [email protected]
ELECTRONIC PROGRAMMER SV
5.3.
How to set the frequency of power supply and the time of phases
This data are factory set before shipment. They can be modified as follows:
1.
2.
3.
4.
5.
6.
7.
8.
push several times the HIDDEN button, until the display shows "Pr--"
push once more the HIDDEN button
push once the button "TIME OF DAY"
the display now shows "Fr50", where 50 is the frequency (Hz) of the available
power supply; push the button "ADVANCE" to modify the pre-set value (50 or 60
Hz) according to local available power supply
WARNING : the setting of a wrong value of the electric frequency will affect the
correct running of the regenerations of the unit
push again the HIDDEN button, the display shows notice "1Cxx", where 1C is the
phase of backwash and xx is the pre-set time, in minutes, as duration of the
phase; push the button "ADVANCE" to modify the pre-set value
push once again HIDDEN button to skip to the next phase
after the modification of the time of last phase 4C, push once again the HIDDEN
button, the display will show notice "End-"; it means the end of programming and
saving of entered data
after one seconds approx the display will show again the current time of day.
WARNING: whether not any button is pushed for 30” before to reach the
visualization of notice “End-“ the programming mode is interrupted
AND ALL MODIFICATIONS ARE LOST.
ALL FACTORY SET OF THE PROGRAMMER ARE LISTED IN THE LAST PAGE
6.
Note
1. The display lights up after several seconds that the power supply has been switched on.
2. The regeneration starts at the scheduled time and day (setting FF....). If the time and/or
day of regeneration is modified, the modification will be accepted by the programmer only
at the midnight (00.00) immediately subsequent the modification.
Example: assumed regeneration scheduled every day (FF01) and at 06.00 p.m. as time of
regeneration. Assumed to modify, at 10.00 a.m. the time of regeneration, and
the new one is 08.00 p.m.: the new setting will be accepted only the day after,
while for the current day the regeneration will start at 06.00 according the
previous schedule.
Therefore, it is not possible to check the immediate automatic starting of a time scheduled
regeneration, but it is required to wait for the day after. Whether a running test is
performed, these information should be taken in consideration: if the programmer is really
defected, the pushing of button "MANUAL REGEN" does not start the regeneration.
3. The light point between 2nd and 3rd digit blinks when the display shows the time of day.
During the programming, it is not blinking and indicates, moving from one point to another,
which is the value/mode on modification.

CALOR SRL Str. Progresul nr. 30-40, sect. 5, Bucuresti
tel: 021.411.44.44, fax: 021.411.36.14
www.calorserv.ro - [email protected]
ELECTRONIC PROGRAMMER SV
4. If the display blinks during visualization of current time of day, it is required to re-adjust the
time of day.
5. In the case of high external electromagnetic interferences or after long period of power
failure (for example during transport and/or storing), it can happen that the display will light
up only partially or will not light up at all.
In this case it is required to reset totally the memory by pushing the special button on the
electronic card , as explained at chaper 4.1 “Memory re-set”
7.
Special programmer with free-voltage contact for remote alarm
One free voltage contacts (max. 1A 250V) can be available, upon request, inside the
programmer. It can be used for a remote signal of the state of regeneration/service.
The terminals of the contacts are marked as follows :
•
•
•
8.
c
nc
na
common
normally closed = regeneration running
normally open = service running
SV programmer : factory set
SV factory standard settings
start regeneration
MODEL
time
liters units correspondence
RATIO
END-CYCLE
reserve
day
READER/METER
UNITS
UNITS
1C
2C
3C
4C
liter per
unit
end cycle
unit
end cycle liters
correspondence
PHASES MINUTES
AC
90/SV 0230
FF04
AA14
3000
0000
03
15
10
10
1
3000
3000
AC
150/SV 0230
FF04
AA14
5000
0000
03
15
15
10
1
5000
5000
AS
90/SV 0230
FF04
AA14
3000
0000
03
15
10
10
1
3000
3000
AS
150/SV 0230
FF04
AA14
5000
0000
03
15
15
10
1
5000
5000
AS
210/SV 0230
FF04
AA14
7000
0000
05
20
15
10
1
7000
7000
AS
300/SV 0230
FF04
AA14
9999
0000
05
20
20
15
1
9999
9999
AS
450/SV 0230
FF04
AA28
7500
0000
05
20
20
15
2
7500
15000
AS
600/SV 0230
FF04
AA28
9999
0000
05
25
20
15
2
9999
20000
AS
800/SV 0230
FF04
AA56
6500
0000
05
25
20
15
4
6500
26000

CALOR SRL Str. Progresul nr. 30-40, sect. 5, Bucuresti
tel: 021.411.44.44, fax: 021.411.36.14
www.calorserv.ro - [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement