5-60-03a

5-60-03a
SERIES 60 SERVICE MANUAL
[a]
Install the gear lash pedestal, J 35596-15, into the threaded hole of the camshaft
drive gear. See Figure 1-331. Bar the engine over until the tool is at the three
o’clock position.
[b]
For Series 60 engines equipped with the compact gear train use the following
procedure: Install the gear lash pedestal J-46303 onto the center of the camshaft gear.
See Figure 1-331a. Adjust it so the dial indicator is positioned at a 90 angle to the
measuring bar and is at the scribe line on the bar.
1. Gear Lash Adjustment Tool
4. Dial Indicator
2. Adjustable Idler Gear Retaining Nut
5. Pedistal Idler Gear Hole
3. Magnetic Base
6. Adjustable Idler Gear Retaining Nut
Figure 1-331
Camshaft Drive Gear-to-Adjustable Idler Gear Lash Measurement
NOTE:
Since the teeth of the camshaft drive gear are not accessible with the gear case cover
installed, the lash is measured on the pedestal installed in the threaded hole, which is
located exactly half-way between the center and edge of the camshaft drive gear. For
this reason, the reading obtained will be exactly 1/2 of the actual gear lash.
NOTE:
For Series 60 engines equipped with the Compact Gear Train Assembly, the gear lash
measuring adaptor has a predetermined spot where the lash measurement must be
taken. The measurement bar must be installed into the magnetic base correctly and the
dial indicator positioned between the marks at the end of the bar.
[c]
Mount a dial indicator adaptor and dial indicator. See Figure 1-331.
All information subject to change without notice.
(Rev. 06/03)
6SE483 0303 Copyright © 2003 DETROIT DIESEL CORPORATION
From Bulletin 5-60-03
1-407
1.21
GEAR TRAIN AND ENGINE TIMING
[d]
For Series 60 engines equipped with the Compact Grear Train Assembly, mount the
dial indicator adaptor and dial indicator, onto the gear case cover. See Figure 1-331a.
[e]
Adjust the stem of the dial indicator to rest on the flat of the pedestal.
[f]
For Series 60 engines equipped with the Compact Gear Train Assembly, adjust the
stem of the dial indicator to rest on the flat of the bar, between the scribed marks on
the end bar and at 90 angle.
[g]
If the adjustable idler gear has been removed, torque the three flanged nuts that retain
the adjustable idler gear hub to the gear case to 57-67 N·m (42-49 lb·ft) to seat the
assembly before proceeding.
1. Adjustable Idler Gear Retaining Nut
3. Dial Indicator
2. Magnetic Base
Figure 1-331a
Compact Gear Train Gear Lash Measurement
[h]
Loosen the three locknuts that retain the adjustable idler gear hub to the gear case
until they are hand tight.
[i]
Insert the dowel portion of the gear lash adjusting tool, J 35596, through the hole in
the adjustable idler gear retaining plate and into the adjustable idler gear hub, using
the bottom two adjustable idler gear cover bolt holes. See Figure 1-331.
NOTE:
For Series 60 engines equipped with the Compact Gear Train Assembly the tool J 35596
has to be modified to fit the four bolt pattern of the idler gear cover. A simple modification
to the mounting plate will allow it to be securely bolted to the cover.
(Rev. 06/03)
1-408
From Bulletin 5-60-03
All information subject to change without notice.
6SE483 0303 Copyright © 2003 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
[j]
Turn the adjusting screw of the tool in a clockwise direction to force the adjustable
idler gear against the camshaft drive gear, until there is zero lash between the two
gears. See Figure 1-332.
Figure 1-332
Adjustable Idler Gear-to-Camshaft Drive Gear Lash Adjustment
[k]
Zero the dial indicator.
[l]
Hold the adjustable idler gear by inserting a screwdriver through the hole provided
in the gear case. Engage one of the adjustable idler gear teeth and apply pressure
on the screwdriver to move the gear in a counterclockwise direction. This will
prevent the gear from moving.
All information subject to change without notice.
(Rev. 06/03)
6SE483 0303 Copyright © 2003 DETROIT DIESEL CORPORATION
From Bulletin 5-60-03
1-409
1.21
GEAR TRAIN AND ENGINE TIMING
Figure 1-332a
Compact Gear Train Gear Lash Adjustment
[m]
For Series 60 engines equipped with the Compact Gear Train Assembly, hold the
adjustable idler gear by inserting a screwdriver through the access hole provided in
the gear case cover. Engage between two of the idler gear teeth and apply upward
pressure on the screwdriver to move the gear in a counterclockwise direction. This
will prevent the gear from moving. See Figure 1-332a.
[n]
Attempt to turn the camshaft drive gear, and watch the dial indicator pointer.
NOTE:
If there is zero lash between the two gears, the dial indicator pointer will not move from
zero.
[o]
Turn the adjusting screw of the gear lash adjusting tool, J 35596, approximately 1-1/2
turns or until the proper gear lash is obtained.
(Rev. 06/03)
1-410
From Bulletin 5-60-03
All information subject to change without notice.
6SE483 0303 Copyright © 2003 DETROIT DIESEL CORPORATION
SERIES 60 SERVICE MANUAL
[p]
When checking gear lash, hold the adjustable idler gear stationary . Refer to step 8[l]
as the first step and refer to step 8[n] as the final step, and rotate the camshaft drive
gear with your right hand. See Figure 1-333
Figure 1-333
Checking Adjustable Idler Gear-to-Camshaft Drive Gear Lash
NOTE:
This note applies only to engines without the Compact Gear Train. Remember
to multiply the reading obtained by two to get the actual lash measurement. The
specification of gear lash is 0.051-0.229 mm (0.002 -0.009 in.) with a maximum of 0.305
mm (0.012 in.) for used parts.
[q]
Check the gear lash with the pedestal at the 3, 6, 9 and 12 o’clock positions, exactly
as previously performed.
[r]
When the proper readings of 0.025-0.114 mm (0.001-0.0045 in.) are obtained at
all four (4) positions, hold the idler gear. Refer to step 8[l] as the first step and
refer to step 8[n] as the final step, and torque the top two adjustable idler gear flanged
nuts to 57-67 N·m (42·49 lb·ft).
[s]
For Series 60 engines equipped with Compact Gear Train Assembly, when the proper
readings of 0.0508-0.2286 mm (0.002-0.009) are obtained at all four (4) positions,
hold the idler gear. Refer to step 8[m]as the first step and refer to step 8[n]as the final
step, and torque the three adjustable idler gear flanged nuts to 103-113 N·m (75-83 lb·ft).
[t]
For Series 60 engines equipped with a Compact Gear Train Assembly procede with
this step next, remove the gear lash adjusting tool from the gear case.
[u]
Check the gear lash again as outlined above, with the flanged nuts torqued, to ensure
that gear lash is still within limits. If not correct repeat the procedure.
All information subject to change without notice.
(Rev. 06/03)
6SE483 0303 Copyright © 2003 DETROIT DIESEL CORPORATION
From Bulletin 5-60-03
1-410a
1.21
GEAR TRAIN AND ENGINE TIMING
[v]
If proper lash measurement cannot be obtained, replace gear(s) with new part(s).
Refer to section 1.24.2, refer to section 1.25.2, refer to section 1.27.2 and
refer to section 1.26.2.
[w]
Remove the gear lash adjusting tool from the gear case.
[x]
Torque the bottom adjustable idler gear flanged nut to 57-67 N·m (42-49 lb·ft) torque.
[y]
Remove the dial indicator and pedestal from the gear case.
[z]
Before installing the rocker arm shaft assemblies, check the torque on the end studs
to ensure they were not loosened at time of removal. The torque specification
is 101-116 N·m (75-86 lb·ft).
[aa]
Install the rocker arm shaft assemblies to the cylinder head. Refer to section 1.3.3.
[ab]
Adjust the intake and exhaust valve clearances, and fuel injector heights.
Refer to section 12.2.
[ac]
Install the valve rocker cover. Refer to section 1.6.8 for a one-piece valve rocker
cover and refer to section 1.6.9 for two-piece and three-piece rocker covers.
[ad]
Install the camshaft drive gear access cover and the gear case cover.
Refer to section 1.10.3.
(Rev. 06/03)
1-410b
From Bulletin 5-60-03
All information subject to change without notice.
6SE483 0303 Copyright © 2003 DETROIT DIESEL CORPORATION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement