ESIM251 Flyer (updated 2013.03.08)

ESIM251 Flyer (updated 2013.03.08)
NEW!
GSM CONTROL SYSTEM ESIM251
1 RELAY
OUTPUT
GSM/GPRS
5 INPUTS
Any alarm system panel
• PGM1
• PGM2
• BELL
10 VOICE MESSAGES
OF A LENGTH OF UP TO
15 SEC. EACH
1. Record your voice message.
2. Upload it to ESIM251.
3. After receiving the signal the system will make
a call. You will hear your recorded message
and/or you will receive an SMS message.
Voice messages of up to 15 seconds
length can be recorded for alarm
and restore event of every input.
SMS/AUDIO
CONFIGURE AND
PROVIDE SERVICE
FOR ESIM251 EASILY
It is not necessary to visit the secured
object or use SMS messages anymore.
Connect to the device over internet
and perform system configurations
& download event log.
GSM CONTROL SYSTEM ESIM251
TECHNICAL SPECIFICATIONS
• GSM Modem Frequency: 850/900/1800/1900 MHz
• Dimensions: 82x63x20mm
• Power Supply Voltage: 10-24V AC/DC
• Inputs: 5
• Operating Temperature: -20...+55°C
(-30...+55°C with limitations)
• Relay Output: 1 (2 relays output optional)
• Event Buffer: 1000
• Output type: NO (relay)
• Microphone connector: Yes
• C1 output maximum commutating values:
1A/24V DC; 0,5A/125V AC
• Authorized users: 5
LIST OF OTHER CONFIGURABLE SYSTEM POSSIBILITIES
Input types
Ways of initiating an
event
Normally open (NO)
Operational only when the signal is transmitted.
Normally closed (NC)
Operational only when the signal is switched.
Event when an input is
violated (Alarm)
Phone call initiated and/or SMS is delivered to user (-s) when the signal is transmitted to
an input.
Event when an input is
restored (Restore)
Phone call initiated and/or SMS is delivered to user (-s) when the previously transmitted
input signal disappears.
Impulse counting
Input is considered as violated only if the number of the preset impulses in the input is
exceeded. Max. value is 4294967295 impulses.
SMS
Ways of notifying about
an event
Phone Call
Turning on/off by SMS
Ways of controlling
outputs
Event log
www.eldes.lt
Turning on/off by a call
The ways of notifying users about events occurred in the particular input can be carried
out only SMS, only a phone call or a combination of both can be chosen. Besides, any of
the users can be assigned to be informed in case a particular input is violated or restored
or both. Various combinations of informing can be assigned for each user and input.
When features SMS All and Call All are enabled, the system sends SMS messages
and rings to all preset users starting with User NR1 despite the fact that the call was
answered or rejected etc.
Examples: User NR1 wants to be informed by SMS in case input Z3 is violated, but does not
want to be informed when input Z3 is restored. User NR3 wants to be informed by SMS and
phone call in case input Z2 is violated, but wants to be informed only by SMS in case of Z2
restore event.
The outputs can be turned on/off by sending the command by SMS message. You can
turn on/off:
1. for a permanent status
2. for a set period
3. for a set hour
4. repeating turning on/off.
The outputs can be turned on/off by calling. You can turn on/off:
1. for a permanent status
2. for a set period
3. toggle (output status changes after each call)
Automatic turning on at
the preset hour
Outputs can be turned on for a set period at a set hour.
E. g. the output is turned on at 18:00 and it is on for 5 hours. After 5 hours it turns off
automatically notifying the user about that.
Event log feature
List of occurred events by date and time - input alarm/restore, output on/off etc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement