Quick Start Guide - LW3211 Series Wireless Security Camera

Quick Start Guide - LW3211 Series Wireless Security Camera
7 2 0P W I RE LESS D IGITAL SECURI TY CAME RA
LW3211 SERIES
QUICK START GUIDE
Getting Started
A. Installing the Camera
1
Mount the camera to the wall or ceiling using the
included screws. Use the included anchors as needed.
2
NOTE: If you run the
cables along the wall /
ceiling, you must run the
cable through the cable
notch on the base. This
will keep the camera
base flush to the wall /
ceiling when mounted.
For outdoor use, installation in a sheltered location is recommended.
This system comes with the
following components:
1x
1x
1x
1x
2x
1x
1x
wireless camera
wireless receiver
antenna for camera
antenna for receiver
power adapters (for camera and receiver)
camera mounting kit
receiver mounting kit
Installation Tips
B. Installing the Receiver
A
Adjust the angle of the camera until the desired
view is set. Tighten the screws and the adjustment
ring to secure the camera position.
C
B
A) Turn the adjustment
ring to tighten / loosen
the stand connection.
B) Loosen the lower
screw with the Allen
key to adjust the camera’s vertical position.
C) Loosen the upper
screw with the Allen
key to rotate the
camera housing.
1
ATTENTION: Make
OPTIONAL:
Extend the cable run of
your video cable and power
adapter up to 60ft with a
compatible extension cable*.
2
Wireless
receiver
3
BNC video
Connect the receiver power adapter to
the receiver. Connect the power adapter
to a power outlet.
OPTIONAL:
Use the double-sided
tape to securely attach
the receiver to a flat
surface. OR secure the
receiver using the included
mounting screws.
Remove protective film from the
camera lens.
Installing Multiple Wireless
Cameras
When installing multiple digital wireless security
cameras in the same environment, maintain at least
4” / 10cm between the receivers to optimize camera
performance.
NOTE: It is not recommended to install more than
3 digital wireless security cameras in the same
environment to maintain optimal video frame rate
performance.
Plan where and how it will be positioned.
Avoid installing the camera in a location where the
wireless signal must pass through cement, concrete,
or metal structures. This will reduce the transmission
range.
4
sure to first connect and
power on the camera before
powering on the receiver.
Before you permanently install your camera:
Verify the camera’s performance by observing
the image on a monitor when the camera is positioned where it will be permanently installed.
Power cables are only weatherproof when fully inserted at
the connection point. Power cables should not be submerged
in water.
Connect the BNC cable to your MPX/HD
DVR’s** video input.
Outdoor Receiver Installation
BNC cable
Determine where you will route the cable that
connects the camera to the power adapter.
Connect the camera power adapter
to the camera. Connect power adapter
to a power outlet.
C. Connecting to an MPX/HD DVR
If mounting the receiver outdoors, refer to the example below. If
installing the receiver indoors, proceed to “Connecting to an
MPX/HD DVR“.
Mounting
screws
3
Power adapter
MPX/HD DVR
*Compatible camera extension cable CB60URB available at www.lorextechnology.com.
NOTE: The camera and receiver have already been paired out of the box. If for some
reason the pairing is lost, follow these steps
to pair up the camera and receiver.
For support and instructions:
1
**720p cameras are compatible with Lorex’s 720p & 1080p HD DVR recorders only.
Make sure that the camera
and receiver are both
powered up and all antennas
properly attached.
2
Press the PAIR button
on the receiver.
3
Press the PAIR button on the back of the
camera within 30 seconds of pressing the
PAIR button on the receiver. If succesful,
live video from the camera will appear on the
monitor.
1
Visit www.lorextechnology.com
2
Search your product’s model number
3
Select your product from the search results
4
Click on the Downloads tab
Pair Button
LW3211_SERIES_QSG_EN_R1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement