INSTALLATION INSTRUCTION

INSTALLATION INSTRUCTION
INSTALLATION
INSTRUCTION
INSTALLATION INSTRUCTIONS FOR
560199
ECONOMIZER USED WITH
(B4,B5)SM 090/120 SERIES AIR HANDLER
FORM # 572D-1210
I - Shipping and Packing List
Package 1 of 1 contains:
1
1
3
14
-
OUTDOOR FRESH AIR
Economizer Assembly
Controls and Wiring Harness Assembly
Wire Nuts
#10 x ½
Check contents for shipping damage. Contact the last carrier
immediately if any shipping damage is found.
II - Application
Economizers are used with Nordyne (B4,B5)SM Series Air
Handlers for automatic sensor-controlled introduction of
outdoor air into the system through an electro-mechanically
controlled damper. Outdoor air is mixed with the buildings return
air to economically improve indoor air quality and aide in
reducing energy costs.
INDOOR RETURN AIR INLET
Economizers can be utilized in either Horizontal or Vertical air
handler applications and are easily mounted over the air
handler return air and filter frame assembly, The C-7150 Mixed
Air Sensor is shipped inside the economizer and must be
relocated downstream of the air handler refrigerant coil in
accordance with these instructions.
ENTHALPY SENSOR
Economizer Supply / Return Duct Connections:
39.75" Wide x 15.63" High (Outside Flange Dimensions)
Warning:
This kit is to be installed by a qualified service
technician in accordance with these instructions and
all codes having jurisdiction. Failure to follow these
instructions could result in serious injury, property
damage, or death. These instructions are primarily
intended to assist qualified individuals experienced in
the proper installation of this appliance. Some local
codes require licensed installation/service personnel
for this type of equipment.
DRIVE MOTOR
W7212 LOGIC MODULE
ELECTRICAL KNOCKOUTS
III - Installation
1. DISCONNECT ALL POWER TO THE UNIT.
2. Install and secure the economizer as shown with the air
handler in the Horizontal position (Figure 1) or in the
Vertical position (Figure 2) using screws (12) provided in
the kit.
NOTE: Economizers must be properly supported when
installed with this air handler. Support for the
economizer is field supplied and the responsibility of
the installer to use methods approved by State or Local
mechanical building codes having jurisdiction. For
Vertical installations, Nordyne Adjustable Support Leg
Kit , SKU # 560258 may be used.
3.
Connect ductwork to the economizer using flanges
provided.
Figure 1 - (B4,B5)SM Horizontal Application
1
INSTALLATION
INSTRUCTION
INSTALLATION INSTRUCTIONS FOR
560199
ECONOMIZER USED WITH
(B4,B5)SM 090/120 SERIES AIR HANDLER
4
Remove the economizer control access panel, the air
handler motor access panel, and the air handler control
panel cover.
5
Remove the electrical knockout on the economizer
next to the damper motor and the plastic plug on the air
handler panel above the control panel, This will allow
routing of the economizer control wiring through a
length of 1" conduit, or other equivalent means of wire
protection based on State or Local codes which covers
24V Class 2 wiring.
6
Cut and discard wire tie securing control wiring bundle
inside the economizer. Remove the two red wires from
the C-7150 Mixed Air Sensor and mount the sensor to
the divider plate located left of the blower motor
assembly as shown in Figure 3 using two screws
provided.
ELECTRICAL
KNOCKOUTS
Important - DO NOT cut other wires. Inspect bundle for
damaged connections or loose wires.
7. Route the nine economizer control wires from the
economizer quick connect plug through the conduit
and into the air handler compartment. Route all wires
except for the two red Mixed Air Sensor wires into the
control panel through the Low Voltage bushing.
MOTOR ACCESS PANEL
Figure 2 - (B4,B5)SM Vertical Application*
8. Connect the two red wires to the Mixed Air Sensor and
secure wires away from the blower and motor
components.
9. Nordyne air handlers are designed to work with either
A/C or Heat Pump outdoor units. Select the proper
wiring diagram for this application on Page 5 and 6 to
connect the remaining seven economizer control wires
to the air handler.
CONTROL PANEL
Replace air handler control panel cover and motor access
panel.
IV - Operation
Note: These instructions are written for the economizer
to operate with a standard single stage Heat/Cool or
Heat Pump thermostat. If 2nd stage mechanical
(compressor) cooling is desired a 2 Stage Cool / 1
Stage Heat thermostat is required.
A. Cooling Mode, Sequence of Operation (Standard)
1. On a call for cooling, with ambient temperature and
humidity above enthalpy control setpoint, the
refrigerant system will operate normally, and damper
will open to minimum vent position. See Section VI for
proper set up and adjustments.
2. On a call for cooling, with outdoor ambient temperature
and humidity suitable for cooling, enthalpy control will
shift stage one cooling control to outside air. The
economizer damper will modulate, mixing outside air
with return air, to control supply air temperature to
approximately 55°F (13°C). If additional cooling is
required, the compressor can be energized through
second stage of an optional two stage Cooling
thermostat. Refer to wiring diagrams for proper
connections.
*
2
MIXED AIR SENSOR
Figure 3 - Mixed Air Sensor Location
Air handler shipped from factory for horizontal application. See air handler installation instructions for
conversion from horizontal to vertical application.
INSTALLATION
INSTRUCTION
INSTALLATION INSTRUCTIONS FOR
560199
ECONOMIZER USED WITH
(B4,B5)SM 090/120 SERIES AIR HANDLER
Figure 4
B. Cooling Mode, Single Enthalpy Control
(Factory Standard)
The C7400A enthalpy control senses both
temperature and humidity or the heat content of
the outside air. It controls the amount of outdoor
air brought into the system. When the heat
content of the outside air is below control
setpoint, the control modulates outdoor dampers
to meet cooling needs of the building. When the
heat content rises above control setpoint, the
control closes outdoor dampers to minimum
position. The recommended setpoint is “A”. If
Economizer is allowing air which is too warm or
too humid to enter the system, control may be
changed to a lower setpoint (B, C, or D). Refer to
Figure 4 and Figure 5.
C. Heating Mode (Heat Pump Application
ONLY)
1. On a call for heat the fresh air damper will
open to the minimum vent position.
V - Economizer Set Up Procedures
Notice to Installer: Proper operation of this
economizer when used with an outdoor HEAT
PUMP system is dependent on the type
thermostat installed with the unit. Identify which
type thermostat is connected to unit before
making any wiring changes if needed.
Figure 5
(B4,B5)SM air handler economizers come equipped with Honeywell
W7212 logic modules which offer additional connections for Demand
Control Ventilation (DCV) and Power Exhaust. Contact your local
Honeywell or Tradeline representative for additional information on
these controls and their specific applications
3
INSTALLATION
INSTRUCTION
INSTALLATION INSTRUCTIONS FOR
560199
ECONOMIZER USED WITH
(B4,B5)SM 090/120 SERIES AIR HANDLER
Heat Pump Thermostat – Single "O/B" terminal for
selection of Reversing Valve Control.
(B4,B5)SM Series economizers are pre-wired to work in
conjunction with single stage Heat Pump thermostats that
utilize the "O" terminal to energize the reversing valve
when the thermostat "System Switch" is set in the "Cool"
mode. Refer to these installation instructions and wiring
diagrams for proper connection and operation of the
economizer. When the system switch is in the OFF, HEAT,
or EMERGENCY HEAT mode setting the economizer is
automatically locked out during heating operation. It holds
the outdoor fresh air damper at the minimum position
setting only when the air handler is operating. Refer to
Section VI – Minimum Damper Position for proper set
up and operation.
VI - SYSTEM CHECK AND START UP
PROCEDURES
Minimum Damper Position Adjustment.
Damper minimum position keeps the outdoor air damper
from closing completely during system operation for
ven ti la tion of build ing con tam i nants and peo ple
occupancy. Consult your State or local codes as required.
1. Disconnect main power to outdoor unit and air
handler.
2. Set thermostat "SYSTEM" switch to "OFF" position and
"FAN" switch to "AUTO".
3. Install jumper wire across air handler low voltage
terminal board "R" and "G" terminal.
4.
Disconnect mixed air sensor from the W7212
terminals T and T1 and short terminals T and T1. See
Figure 5.
5. Ensure the factory installed jumper is in place across
terminals P and P1.
6. Calculate the appropriate mixed air temperature per
the following equation:
*
(Return Air Temp. x % of Return Air) + (Outside Air
Temp. x % of Outside Air) = Mixed Air Temperature
Example:
Assume local code requires 10% outdoor air during
occupied conditions, (200 CFM of total unit CFM =
2,000) outdoor air is 60oF, and return air is 75oF.
Under these conditions, what is the mixed air
temperature?
(0.1 x 60oF) + (0.9 x 75oF) = 6.0oF + 67.5oF = 73.5 oF
7. Restore power to the outdoor section and air handler.
8. Carefully adjust the MIN POS potentiometer on the
W7212 control module with a small screwdriver until
the mixed air temperature reaches the calculated
value.
9. Once minimum position adjustments are completed,
turn off power to the outdoor unit and air handler.
Damper will move to fully close.
4
10. Remove jumper wire across "R" and "G" on the low
voltage terminal board and T and T1 on the W7212
control module.
11. Reconnect the mixed air sensor.
12. Restore power to outdoor unit and air handler.
VII - MAINTENANCE
1. Damper motor is prelubricated and does not require
further lubrication.
2. Make visual inspection of dampers and linkage
assemblies during routine maintenance.
3. Filters should be checked periodically and cleaned
when necessary.
4. The washable filters supplied with the economizer can
be cleaned with water and a mild detergent.
5. Take note of “Air Flow Direction” marking on filter
frame when reinstalling.
6. If filter must be replaced, filter of like kind and size must
be used. DO NOT replace permanent filters with
throwaway type filters.
4.
3.
1.
2.
Economizer
C7400A
C7150
MS7510A
W7212A
TB-11
Fresh Air Enthalpy Sensor
Mixed Air Sensor
Damper Actuator 24v
Logic Module
Terminal Block
COMPONENT CODE
BLK
BRN
GRY
RED
YEL
Black
Brown
Gray
Red
Yellow
BLU
GRN
ORN
VIO
WHT
WIRE COLOR CODE
C & W2 to be connected to optional electric heat.
Remove BLACK wire from air handler low voltage terminal board Y terminal and connect to YELLOW wire from
economizer.
Second Stage refrigerant cooling with optional economizer installed. A 2 stage thermostat is required for
simultaneous operation of the economizer and refrigerant system. Connect Y2 from 2 stage thermostat to
BLUE wire from economizer.
Heat Pump Economizer Relay. For heat pump applications only. Required for proper operation of an
economizer (optional) in the heat pump Heating mode. CONNECT TO "R" FOR AC ONLY APPLICATIONS.
E# = WIRE END DESIGNATION
E2 STUD #6 18 Ga. Wire
E3 Female ¼ Quick Disc.
E4 Male ¼ Quick Disc. Insul
E6 Wire Nut Size 73B
HARNESS DETAIL
Change
Date
Date: February 4, 2011
Supersedes:
Drawn by:
Unit #: 47-374-01
Diagram#: 4737401w
Approved by:
Modulating Economizer
560199
(B4,B5)SM 090/120 Series Air Handler
Blue
Green
Orange
Violet
White
Revision
5.
4.
1.
2.
3.
Economizer
C7400A
C7150
MS7510A
W7212A
TB-11
Fresh Air Enthalpy Sensor
Mixed Air Sensor
Damper Actuator 24v
Logic Module
Terminal Block
COMPONENT CODE
BLK
BRN
ORN
VIO
WHT
Black
Brown
Orange
Violet
White
BLU
GRN
RED
YEL
WIRE COLOR CODE
Jumper between W2 and E is required.
C & W2 to be connected to electric heat.
Remove BLACK wire from air handler low voltage terminal board Y terminal and connect to YELLOW wire from
economizer.
Second Stage refrigerant cooling with optional economizer installed. A 2 stage thermostat is required for
simultaneous operation of the economizer and refrigerant system. Connect Y2 from 2 stage thermostat to
BLUE wire from economizer.
Heat Pump Economizer Relay. Required for proper operation of an economizer (optional) in the heat pump
Heating mode. Refer to economizer installation instruction for proper connection to thermostat.
E# = WIRE END DESIGNATION
E2 STUD #6 18 Ga. Wire
E3 Female ¼ Quick Disc.
E4 Male ¼ Quick Disc. Insul
E6 Wire Nut Size 73B
HARNESS DETAIL
Change
Date
Date: February 4, 2011
Supersedes:
Drawn by:
Unit #: 47-374-01
Diagram#: 4737402w
Approved by:
Modulating Economizer
560199
(B4,B5)SM 090/120 Series Air Handler
Blue
Green
Red
Yellow
Revision
7
FEBRUARY 4, 2011
8
NEIMB01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement