R&S®ZVA110 Network Analyzer
ZVA110_dat-sw_en_5214-4813-22_cover.indd 1
Data Sheet | 04.00
Test & Measurement
R&S®ZVA110
Vector Network Analyzer
Specifications
15.11.2013 14:42:28
Version 04.00, November 2013
CONTENTS
Definitions ....................................................................................................................................................................... 3
Specifications .................................................................................................................................................................. 4
Overview ........................................................................................................................................................................................... 4
Measurement range .......................................................................................................................................................................... 5
Test port output ................................................................................................................................................................................. 5
Test port input ................................................................................................................................................................................... 7
System characteristics ....................................................................................................................................................................... 7
Additional front panel connectors ....................................................................................................................................................... 7
Display .............................................................................................................................................................................................. 7
Rear panel connectors....................................................................................................................................................................... 7
General data...................................................................................................................................................................................... 9
Ordering information .................................................................................................................................................... 10
2
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
Version 04.00, November 2013
Definitions
General
Product data applies under the following conditions:
•
•
•
•
Three hours storage at ambient temperature followed by 30 minutes warm-up operation
Specified environmental conditions met
Recommended calibration interval adhered to
All internal automatic adjustments performed, if applicable
Specifications with limits
Represent warranted product performance by means of a range of values for the specified parameter. These specifications are
marked with limiting symbols such as <, ≤, >, ≥, ±, or descriptions such as maximum, limit of, minimum. Compliance is ensured by
testing or is derived from the design. Test limits are narrowed by guard bands to take into account measurement uncertainties, drift
and aging, if applicable.
Specifications without limits
Represent warranted product performance for the specified parameter. These specifications are not specially marked and represent
values with no or negligible deviations from the given value (e.g. dimensions or resolution of a setting parameter). Compliance is
ensured by design.
Typical data (typ.)
Characterizes product performance by means of representative information for the given parameter. When marked with <, > or as a
range, it represents the performance met by approximately 80 % of the instruments at production time. Otherwise, it represents the
mean value.
Nominal values (nom.)
Characterize product performance by means of a representative value for the given parameter (e.g. nominal impedance). In contrast to
typical data, a statistical evaluation does not take place and the parameter is not tested during production.
Measured values (meas.)
Characterize expected product performance by means of measurement results gained from individual samples.
Uncertainties
Represent limits of measurement uncertainty for a given measurand. Uncertainty is defined with a coverage factor of 2 and has been
calculated in line with the rules of the Guide to the Expression of Uncertainty in Measurement (GUM), taking into account
environmental conditions, aging, wear and tear.
Device settings and GUI parameters are indicated as follows: “parameter: value”.
Typical data as well as nominal and measured values are not warranted by Rohde & Schwarz.
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
3
Version 04.00, November 2013
Specifications
Overview
The R&S®ZVA110 is a 1.0 mm vector network analyzer system, covering the frequency range from 10 MHz to 110 GHz.
The R&S®ZVA110 vector network analyzer system consists of one R&S®ZVA67 four-port vector network analyzer
(with -B16 and -K8 option) and two external test sets
Each of the external test sets is formed by a R&S®ZVA-Z110E frequency converter and a R&S®ZVA-ZD110 diplexer. The system can
also be operated without the R&S®ZVA-ZD110 diplexers, yielding a two port waveguide measurement system with a WR10 test port.
Specifications relevant to this operating mode can be found in the R&S®ZVA-Zxx data sheet PD 5214.2033.22
4
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
Version 04.00, November 2013
The following specifications apply for operation as a 1.0 mm vector network analyzer system. The specified data is only valid for a
system configuration identical to the designation scheme at the rear panel of the R&S®ZVA67, with respect to the type and serial
numbers as well as the correct position on the “right” or “left” side of the system. The position “left” is operated by ports 1 and 3 and
position “right” by ports 2 and 4.
Measurement range
Impedance
Test port connector
Number of test ports
Frequency range
Static frequency accuracy
50 Ω
1.0 mm, male
2
R&S®ZVA110
10 MHz to 110 GHz
without optional oven quartz
8×10–6
with optional oven quartz
1×10–7
Frequency resolution
1 Hz
Number of measurement points
user-selectable
1 to 60001
Measurement bandwidths
1/2/5 steps
1 Hz to 1 MHz
Dynamic range
10 MHz to 50 MHz
> 50 dB, typ. 60 dB
50 MHz to 500 MHz
> 90 dB, typ. 103 dB
500 MHz to 2 GHz
> 113 dB, typ. 123 dB
2 GHz to 20 GHz
> 120 dB, typ. 130 dB
20 GHz to 24 GHz
> 110 dB, typ. 120 dB
24 GHz to 32 GHz
> 106 dB, typ. 116 dB
32 GHz to 40 GHz
> 97 dB, typ. 110 dB
40 GHz to 50 GHz
> 87 dB, typ. 105 dB
50 GHz to 60 GHz
> 80 dB, typ. 94 dB
60 GHz to 75 GHz
> 75 dB, typ. 85 dB
75 GHz to 110 GHz
> 80 dB, typ. 89 dB
The dynamic range is defined as the difference between the actually available maximum source power and the RMS value of the
data trace of the transmission magnitude, which is produced by noise and crosstalk with the test ports short-circuited. The
specification is valid without system error correction and at 10 Hz measurement bandwidth. The dynamic range can be increased by
using a measurement bandwidth of 1 Hz.
Test port output
Output power
Output power accuracy
(with power calibration)
1
10 MHz to 50 MHz
50 MHz to 500 MHz
500 MHz to 20 GHz
20 GHz to 32 GHz
32 GHz to 50 GHz
50 GHz to 60 GHz
60 GHz to 67 GHz
67 GHz to 75 GHz
75 GHz to 110 GHz
500 MHz to 24 GHz
24 GHz to 67 GHz
67 GHz to 110 GHz
–30 dBm to +5 dBm 1.
–30 dBm to +6 dBm 1
–30 dBm to +8 dBm 1
–30 dBm to +3 dBm 1
–30 dBm to –4 dBm 1
–35 dBm to –12 dBm 1
–37 dBm to –17 dBm 1
–30 dBm to –17 dBm 1
–28 dBm to –11 dBm 1
< 0.8 dB, typ. 0.3 dB
< 2 dB, typ. 1 dB
< 3 dB, typ. 2 dB
Electrically adjustable.
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
5
Version 04.00, November 2013
Dynamic range in dB versus frequency in GHz of the R&S®ZVA110.
Maximum output power in dBm versus frequency in GHz of the R&S®ZVA110.
6
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
Version 04.00, November 2013
Test port input
Damage level
+27 dBm
System characteristics
This data is valid between +18 °C and +28 °C, provided the temperature has not varied by more than 1 K after calibration. The data is
based on a measurement bandwidth of 10 Hz and system error calibration by means of a suitable calibration kit. Frequency points,
measurement bandwidth, and sweep time have to be identical for measurement and calibration (no interpolation allowed).
System characteristics of R&S®ZVA110
Trace stability
(transmission of the through standard)
Effective source match
(with system error correction)
Effective directivity
(with system error correction)
Effective load match
(with system error correction)
10 MHz to 110 GHz
typ. < 0.4 dB and typ. < 4°
10 MHz to 110 GHz
typ. > 32 dB
10 MHz to 110 GHz
typ. > 32 dB
10 MHz to 110 GHz
typ. > 32 dB
Additional front panel connectors
USB
(two) universal serial bus connectors for connecting USB devices (USB 2.0); two
additional USB connectors at the rear panel
Display
Screen
Resolution
26 cm (10.4") diagonal color LCD
800 × 600 × 262144 pixel (high color)
Rear panel connectors
IEC BUS
remote control in line with IEEE 488, IEC 60625; 24 pins
LAN 1
first local area network connector, 8 pins, RJ-45
LAN 2
second local area network connector, 8 pins, RJ-45
USB
(two) universal serial bus connectors for connecting USB devices (USB 2.0);
two additional USB connectors at the front panel
10 MHz REF
Connector type
Input frequency
Maximum permissible deviation
Input power
Input impedance
Output frequency
Output frequency accuracy
Output power
alternatively input or output for external frequency reference signal
BNC, female
10 MHz
1 kHz
–3 dBm ± 8 dB
50 Ω
10 MHz
80 Hz
–3 dBm ± 8 dB at 50 Ω
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
7
Version 04.00, November 2013
DC MEAS 1 V
Connector type
Voltage range
Measurement accuracy
Resolution
Sample rate
Input impedance
Damage voltage
DC measurement input
DC MEAS 10 V
Connector type
Voltage range
Measurement accuracy
Resolution
Sample rate
Input impedance
Damage voltage
DC measurement input
PORT BIAS
Connector type
Maximum nominal input voltage
Maximum nominal input current
Damage voltage
Damage current
DC bias input for 1.0 mm PORT
MONITOR
USER CONTROL
FOOT SWITCH 1 and FOOT SWITCH 2
DRIVE PORT 1 to DRIVE PORT 4
CHANNEL BIT 0 and CHANNEL BIT 1
CHANNEL BIT 2 and CHANNEL BIT 3
PASS 1 and PASS 2
BUSY
READY FOR TRIGGER
EXT GEN TRIGGER
EXT GEN BLANK
EXTERNAL TRIGGER
EXT TRIGGER
Connector type
TTL signal (edge-triggered)
Polarity (user-selectable)
Minimum pulse width
Input impedance
8
4-pin mini DIN, female
–1 V to +1 V
2.5 % of reading + 2.5 mV
12 bit
3 MHz
> 10 kΩ
30 V
4-pin mini DIN, female
–10 V to +10 V
2.5 % of reading + 25 mV
12 bit
3 MHz
> 10 kΩ
30 V
BNC, female
30 V
200 mA
30 V
500 mA
IBM-PC-compatible VGA monitor
connector, 15-pin D-Sub (for external
monitor)
several control and trigger signals, 25-pin D-Sub, 3.3 V TTL
for controlling external generators, for limit checks, sweep signals, etc.
pin 24 and pin 25 (inputs)
control inputs
pin 16 to pin 19 (outputs)
indicate driving port
pin 8 and pin 9 (outputs)
not available
pin 10 and pin 11 (outputs)
channel-specific user-configurable bits
pin 13 and pin 14 (outputs)
pass/fail results of limit checks
pin 4 (output)
measurements running
pin 6 (output)
ready for trigger
pin 21 (output)
control signal for external generator
pin 22 (input)
handshake signal from external generator
pin 2 (input)
trigger input for analyzer
trigger input for analyzer
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
BNC, female
3V
positive or negative
1 µs
> 10 kΩ
Version 04.00, November 2013
General data
Temperature loading
Damp heat
Mechanical resistance
Calibration interval
EMC, RF emission
EMC, immunity
Safety
Power supply
Power consumption
Dimensions (W × H × D)
Weight
Shipping weight
in line with IEC 60068-2-1 and IEC 60068-2-2
operating temperature range
+18 °C to +28 °C
permissible temperature range
+5 °C to +40 °C
storage temperature range
–40 °C to +70 °C
+40 °C at 80 % rel. humidity,
in line with IEC 60068-2-30
vibration, sinusoidal
5 Hz to 150 Hz,
in line with IEC 60068-2-6
vibration, random
10 Hz to 300 Hz,
in line with IEC 60068-2-64
shock
40 g shock spectrum,
in line with MIL-STD-810E
Method No. 516.4 procedure I
1 year
in line with EN 55011 class A, operation in line with CISPR 11/EN 55011 group 1
is not covered in residential, commercial, class A (for a shielded test setup)
and business areas nor in small-size
The instrument complies with the emission
companies. Thus, the instrument must
requirements stipulated by EN 55011 and
not be operated in residential,
EN 61326-1 class A. This means that the
commercial, and business areas nor in
instrument is suitable for use in industrial
small-size companies unless additional
environments.
measures are taken to ensure that
EN 55011 class B is met.
in line with IEC/EN 61326-1,
immunity for industrial environments
(excluding operating frequency)
in line with IEC 61010-1, EN 61010-1 and
UL 3111-1
R&S®ZVA67
100 V to 240 V (AC) with tolerance ±10 %,
50 Hz to 60 Hz with tolerance ±5 %,
safety class I to VDE 411
each external test set
power adapter,
(consisting of R&S®ZVA-Z110 and
100 V to 240 V (AC) with tolerance ±10 %,
R&S®ZVA-ZD110)
50 Hz to 60 Hz with tolerance ±5 %,
safety class II
output: 9 V, max. 1.1 A DC
output connector: DIN 45323
R&S®ZVA67
450 W, typ. 310 W (standby: typ. 10 W)
each external test set
10 W, typ. 7 W
(consisting of R&S®ZVA-Z110 and
R&S®ZVA-ZD110)
R&S®ZVA67
465.1 mm × 286.2 mm × 495.0 mm
(18.31 in × 11.27 in × 19.49 in)
each external test set
525 mm × 110 mm × 114 mm
(consisting of R&S®ZVA-Z110 and
(20.7 in × 4.3 in × 4.5 in)
R&S®ZVA-ZD110)
R&S®ZVA67
25 kg (55 lb)
each external test set
4.2 kg (9.3 lb)
(consisting of R&S®ZVA-Z110 and
R&S®ZVA-ZD110)
R&S®ZVA67
37 kg (82 lb)
each external test set
6.2 kg (13.6 lb)
(consisting of R&S®ZVA-Z110 and
R&S®ZVA-ZD110)
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
9
Version 04.00, November 2013
Ordering information
Designation
Vector Network Analyzer, 110 GHz, two ports, complete system
based on R&S®ZVA67
Vector Network Analyzer, 110 GHz, two ports, complete system
based on R&S®ZVA67, without RF cables 2
Options
Time Domain
Pulsed Measurements
5 MHz Receiver Bandwidth
Internal Pulse Generators
Service options
Extended Warranty, one year
Extended Warranty, two years
Extended Warranty, three years
Extended Warranty, four years
Extended Warranty with Calibration Coverage, one year
Extended Warranty with Calibration Coverage, two years
Extended Warranty with Calibration Coverage, three years
Extended Warranty with Calibration Coverage, four years
Type
R&S®ZVA110
Order No.
1312.7004.03
R&S®ZVA110
1312.7004.05
R&S®ZVAB-K2
R&S®ZVA-K7
R&S®ZVA-K17
R&S®ZVA-K27
1164.1657.02
1164.1511.02
1164.1070.02
1164.1892.02
R&S®WE1
R&S®WE2
R&S®WE3
R&S®WE4
R&S®CW1
R&S®CW2
R&S®CW3
R&S®CW4
Please contact your local
Rohde & Schwarz sales office.
Extended warranty with a term of one to four years (WE1 to WE4)
Repairs carried out during the contract term are free of charge 3. Necessary calibration and adjustments carried out during repairs are
also covered. Simply contact the forwarding agent we name; your product will be picked up free of charge and returned to you in top
condition a couple of days later.
Extended warranty with calibration (CW1 to CW4)
Enhance your extended warranty by adding calibration coverage at a package price. This package ensures that your
Rohde & Schwarz product is regularly calibrated, inspected and maintained during the term of the contract. It includes all repairs 3 and
calibration at the recommended intervals as well as any calibration carried out during repairs or option upgrades.
For product brochure, see PD 5213.5680.12 and www.rohde-schwarz.com.
2
Model 1312.7004.05 is identical to model 1312.7004.03 except the six RF cables R&S®ZV-Z196 (1306.4736.00) from the R&S®ZVA67 to the
R&S®ZVA-ZD110 diplexers and the two LO feed cables R&S®ZV-Z193 (1306.4720.00) from the R&S®ZVA67 to the R&S®ZVA-Z110E frequency
converters, which will not be supplied. Data sheet specifications do apply if the R&S®ZVA110 system is set up with aforementioned cables,
only.
3
Excluding defects caused by incorrect operation or handling and force majeure. Wear-and-tear parts are not included.
10
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
Version 04.00, November 2013
Rohde & Schwarz R&S®ZVA110 Vector Network Analyzer
11
Service that adds value
Worldwide
Local and personalized
❙ Customized and flexible
❙ Uncompromising quality
❙ Long-term dependability
❙
❙
About Rohde & Schwarz
Rohde & Schwarz is an independent group of companies
specializing in electronics. It is a leading supplier of solutions in the fields of test and measurement, ­broadcasting,
radiomonitoring and radiolocation, as well as secure
communications. Established more than 75 years ago,
­Rohde & Schwarz has a global presence and a dedicated
service network in over 70 countries. Company headquarters are in Munich, Germany.
Environmental commitment
❙❙ Energy-efficient products
❙❙ Continuous improvement in environmental sustainability
❙❙ ISO 14001-certified environmental management system
Certified Quality System
ISO 9001
Rohde & Schwarz GmbH & Co. KG
www.rohde-schwarz.com
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG
Trade names are trademarks of the owners
PD 5214.4813.22 | Version 04.00 | November 2013 (as)
R&S®ZVA110 Vector Network Analyzer
Data without tolerance limits is not binding | Subject to change
© 2010 - 2013 Rohde & Schwarz GmbH & Co. KG | 81671 München, Germany
5214.4813.22 04.00 PDP 1 en
Regional contact
❙❙ Europe, Africa, Middle East | +49 89 4129 12345
[email protected]
❙❙ North America | 1 888 TEST RSA (1 888 837 87 72)
[email protected]
❙❙ Latin America | +1 410 910 79 88
[email protected]
❙❙ Asia/Pacific | +65 65 13 04 88
[email protected]
❙❙ China | +86 800 810 8228/+86 400 650 5896
[email protected]
5214481822
ZVA110_dat-sw_en_5214-4813-22_cover.indd 2
15.11.2013 14:42:28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement