View detail for AT88CK101BK8 Hardware User Guide

View detail for AT88CK101BK8 Hardware User Guide
Atmel CryptoAuthentication Starter Kit
Atmel AT88CK101BK8
Hardware User Guide
Features
Contents
 8-lead SOIC socket
 Atmel AT88CK101BK8 daughterboard
 Supports the Atmel ATSHA204 CryptoAuthentication IC
 Supports communication protocols
- I2C
- SWI (Single wire interface)
 Power LED
 Test points header
1.
Introduction
Atmel® AT88CK101BK8 is a daughterboard that interfaces with a mcu board via a 10-pin header. The
daughterboard has a single 8-pin SOIC socket which can support the Atmel ATSHA204. This kit uses a
modular approach, enabling the daughterboard to connect directly to an STK series AVR development
platform to easily add security to applications. An optional adapter kit is also available when the 10-pin
header on the daughterboard requires a different pinout. The AT88CK101BK8 also provides a test point
header for the I2C, SWI, and SPI signals. The AT88CK101BK8 is sold with the Atmel AT88Microbase
module to form the Atmel AT88CK101STK8 starter kit. The AT88Microbase AVR base board comes with a
USB interface that lets designers learn and experiment on their PCs.
Figure 1-1.
Atmel AT88CK101BK8 Crypto daughterboard
Standoff hole
Pin 1 indicator
Standoff hole
K1
communication
protocol selector
Test point
header
8741A–CRYPTO–3/11
1.1.
Atmel AT88CK101STK8 starter kit
The AT88CK101BK8 is sold with the Atmel AT88Microbase module to form the Atmel AT88CK101STK8
starter kit. For additional information on the AT88Microbase, See Atmel doc8723A, Atmel AT88Microbase
Hardware User Guide.
2
Figure 1-2.
Atmel AT88CK101STK8 starter kit
Figure 1-3.
The Atmel AT88CK101BK8 daughterboard with the Atmel AT88Microbase
Atmel AT88CK101BK8 Hardware User Guide
8741A–CRYPTO–3/11
2.
Board configuration
2.1.
10-pin interface header
Table 2-1. 10-pin interface header
P10
VCC
Note:
2.2.
P9
P8
P7
P6
P5
P4
P3
P2
P1
GND
NC
NC
NC
NC
MISO
MOSI
SDA/SCLK
SCL /CS
2
I C Pins: SCL, SDA
SPI Pins: /CS, SCLK, MOSI, MISO
6-pin test header
Table 2-2. 6-pin test header
/CS
SCL
SI/SDA
S0
VCC
GND
SPI chip select
SPI-CLK
MOSI/SDA
MISO
VCC
GND
Note:
2.3.
2
I C Pins: SCL, SDA
SPI Pins: /CS, SCLK, MOSI, MISO
Supports 8-lead SOIC and SPI interfaces with the following pinout
Figure 2-1.
Pinout configurations
8-lead SOIC
NC
NC
1
8
2
7
NC
GND
3
6
4
5
8-lead SOIC
VCC
NC
SCL
SDA
/CS
SO
NC
1
8
2
7
3
6
VCC
NC
SCK
GND
4
5
SI
Atmel AT88CK101BK8 Hardware User Guide
8741A–CRYPTO–3/11
3
2.4.
Configurations
Table 2-3 describes the how to configure the AT88CK101BK8 with respect to the AT88Microbase and the
STK/EVK development platforms.
Table 2-3. Atmel AT88CK101STK8 starter kit configuration guide
Atmel AT88CK101STK8 starter kit configuration guide
Communication interface
Atmel AT88Microbase
(K1 switch)
Atmel AT88CK101BK8
(K1 switch)
Atmel AT88CK101BK8
jumper (H5)
TWI
TWI
uBase
Open
SPI
SPI
uBase
Mounted
SWI (UART)
─
SPI
Mounted
SWI (GPIO)
SPI
uBase
Open
Atmel AT88CK101BK8+ STK/EVK platforms configuration guide
Communication interface
─
Atmel AT88CK101BK8
(K1 switch)
Atmel AT88CK101BK8
jumper (H5)
TWI
─
TWI
Open
SPI
─
SPI
Open
SWI (UART)
─
SPI
Mounted
SWI (GPIO)
─
TWI
Signal on Px1
(x-denotes the port)
Open
Note:
X = Don’t care
Figure 2-2.
4
Atmel AT88CK101BK8 adapter board mounted to STK600
Atmel AT88CK101BK8 Hardware User Guide
8741A–CRYPTO–3/11
2.5.
AT88CK301ADP adapter kit
An optional adapter kit is also available when the 10-pin header on the daughterboard requires a different
pinout.
Figure 2-3.
Atmel AT88CK301ADP adapter kit
Figure 2-4.
Atmel AT88CK101BK8 and Atmel AT88CK301ADP with the Atmel AT91SAM7S-EK board
Table 2-4. 10 pin squid cable
10 pin squid cable
P10
P9
P8
P7
P6
P5
P4
P3
P2
P1
black
white
gray
purple
blue
green
yellow
orange
red
brown
Atmel AT88CK101BK8 Hardware User Guide
8741A–CRYPTO–3/11
5
3.
References and further information
Schematics, Gerber files, bill of materials (BOM), development and demonstration software is conveniently
downloadable from the Atmel website at www.atmel.com/cryptokits.
4.
EVALUATION BOARD/KIT IMPORTANT NOTICE
This evaluation board/kit is intended for ENGINEERING, DEVELOPMENT, DEMONSTRATION or
EVALUATION PURPOSE ONLY. It is not a finished product and may not (yet) comply with some or
any technical or legal requirements that are applicable to finished products, including, without limitations,
directives regarding electromagnetic compatibility, recycling (WEEE), FCC, CE or UL (except as may be
otherwise noted on the board/kit). Atmel® supplied this board/kit “AS IS,” without any warranties, with
all faults, at the buyer’s and further users’ sole risk. The user assumes all responsibly and liability for
proper and safe handling of goods. Further, the user indemnifies Atmel from claims arising from the
handling or use of goods. Due to open construction of the product, it is the user’s responsibility to take
any and all appropriate precautions with regard to electrostatic discharge and any other technical or legal
concerns.
EXCEPT TO THE EXTENT OF INDEMNITY SET FORTH ABOVE, NEITHER USER NOR ATMEL SHALL BE
LIABLE TO EACH OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
No license is granted under any patent right or other intellectual property right of Atmel covering or
relating to any machine, process, or combination in which such Atmel product or services might be or are
used.
Mailing Address: Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
6
Atmel AT88CK101BK8 Hardware User Guide
8741A–CRYPTO–3/11
Atmel Corporation
Atmel Asia Limited
Atmel Munich GmbH
Atmel Japan
2325 Orchard Parkway
Unit 01-5 & 16, 19F
Business Campus
9F, Tonetsu Shinkawa Bldg.
San Jose, CA 95131
BEA Tower, Millennium City 5
Parkring 4
1-24-8 Shinkawa
USA
418 Kwun Tong Road
D-85748 Garching b. Munich
Chuo-ku, Tokyo 104-0033
Tel: (+1)(408) 441-0311
Kwun Tong, Kowloon
GERMANY
JAPAN
Fax: (+1)(408) 487-2600
HONG KONG
Tel: (+49) 89-31970-0
Tel: (+81)(3) 3523-3551
www.atmel.com
Tel: (+852) 2245-6100
Fax: (+49) 89-3194621
Fax: (+81)(3) 3523-7581
Fax: (+852) 2722-1369
© 2011 Atmel Corporation. All rights reserved. / Rev.: 8741A–CRYPTO–3/11
Atmel®, logo and combinations thereof, CryptoAuthentication™ and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other
terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in
connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATM EL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS
ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF ME RCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND
PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMEN T, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel
makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and rese rves the right to make changes to specifications and products descriptions at any time without
notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise , Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel
products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life .
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement