iMcV-10G-Converter FCC Radio Frequency Interference Statement

iMcV-10G-Converter FCC Radio Frequency Interference Statement
FCC Radio Frequency Interference Statement
iMcV-10G-Converter
XFP/XFP
Operation Manual
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Limited Lifetime Warranty
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B Electronics warrants that each such
product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicable
solely to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation, connection, operation and maintenance of
products in accordance with their written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any warranty or indemnity offered by B&B
Electronics, but may be subject to the warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics have any warranty obligations or any other
liability for: (i) any defects resulting from wear and tear, accident, improper use by the buyer or use by any third party
except in accordance with the written instructions or advice of the B&B Electronics or the manufacturer of the products,
including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products which have
been adjusted, modified or repaired by any party other than B&B Electronics or (iii) any descriptions, illustrations, figures
as to performance, drawings and particulars of weights and dimensions contained in the B&B Electronics’ catalogs, price
lists, marketing materials or elsewhere since they are merely intended to represent a general idea of the products and do
not form part of this price quote and do not constitute a warranty of any kind, whether express or implied, as to any of the
B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET
FORTH ABOVE IS B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY CONTAINED
IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE
INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B ELECTRONICS BE LIABLE FOR
LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES. B&B ELECTRONIC SHALL
DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR INDEMNITIES MADE BY ANY
OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF
B&B ELECTRONIC WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.
ii
Table of Contents
About the iMcV-10G-Converter XFP/XFP
FCC Radio Frequency Interference Statement .................................................... ii Limited Lifetime Warranty .................................................................................. ii About the iMcV-10G-Converter XFP/XFP............................................................1 Configuration Instructions ..................................................................................1 Installing an iMcV-Modules ................................................................................1 Managed Modules .............................................................................................1 Configuration Control and SNMP Management ..................................................2 LED Operation ...................................................................................................7 Specifications .....................................................................................................8 B&B Electronics Technical Support .....................................................................9 Fiber Optic Cleaning Guidelines.........................................................................9 Electrostatic Discharge Precautions ...................................................................11 Certifications ....................................................................................................12 The iMcV-10G-Converter is a dual wide module that can be installed in an
iMediaChassis series, a MediaChassis /2 or an IE-MediaChassis/2.
The iMcV-10G-Converter is a media converter module with XFP ports which can
provide a conversion between different fiber types or copper to fiber. Fiber types
include Single Mode (SM) and Multi Mode (MM). The supported transmission speeds
are: 10G Ethernet, 10G Sonet/SDH, 10G Fiber channel and 10G OTN. The copper
SFP supports 10G Ethernet only.
Configuration Instructions
The iMcV-10G-Converter modules have user-configurable features (e.g., Loss Carry
Forward (LCF), speed (based on protocol selection) and loopback.
Installing an iMcV-Modules
The iMcV-10G-Converter can be installed in B&B Electronics’ SNMP manageable
iMediaChassis, MediaChassis/2 AC or DC, or IE-MediaChassis/2 AC or DC.
NOTE
All modules are hot-swappable.
To install an iMcV-10G-Converter:
1.
Remove the blank bracket covering the slot where the module is to be installed
by removing the screws on the outside edges of the bracket.
2.
Slide the iMcV-10G-Converter into the chassis, via the cardguides, until the
module is seated securely in the connector.
3.
Secure the module to the chassis by tightening the captive screw.
4.
Save any “blanks” removed during installation for future use if the configuration
requirements change.
Managed Modules
To manage one or more iMcV-Modules, a SNMP Management Module must be
installed in an iMediaChassis series, available in 3, 6 or 20 slots for both AC and DC.
Using management, the 10G converter will be identified in the slot it is installed in, as
iii
1
well as options to set LoopBack and Loss Carry Forward (LCF). However, the Module
details includes an XFP table so that management can provide information about the
XFP if and XFP with DDMI is installed. The XFP table provides information such as
temperature, voltage, output power, receive power, vendor serial number, vendor
part number and vendor name.
iMcV-10G-Converter requires SNMP binary 953-00D1 or higher.
Configuration Control and SNMP Management
2.
The Management Module can be added to a chassis without losing any
configuration.
3.
The Management Module should not be subjected to failure or interruption in a
“Mission Critical” environment. If the Management Module is removed or fail,
the modules should not experience an interruption in service.
There are two features that have been incorporated in Configuration Control:
1.
Any module, including the Management Module, can be physically swapped out
with the identical module under power and the configuration from the removed
module will be automatically copied to the new module.
Its main function is to assist the end-user by retaining the latest configuration
regardless of how the initial configuration was setup, whether through DIP Switch
settings or the SNMP Management Module’s configuration.
2.
The module’s DIP Switch settings can be used to make initial configuration
settings, overriding the Management Module’s setting. (see contents below for
clarification)
Configuration Control was created to solve several issues:
Inserting a iMcV-module
1.
-
Some iMcV-Modules* offer Configuration Control. Labels on the front faceplate will
identify if the iMcV-module has Configuration Control.
2.
3.
When non-Configuration Control modules are placed in a managed chassis, the
module’s DIP Switches are ignored, and the module is configured by the chassis’
Management Module. If the Management Module is removed or fails, then the
modules will revert back to the DIP Switch settings. When a module changes
from Management Module settings to DIP Switch settings, the traffic across the
module will drop for a very short period of time.
When introducing a Management Module to a chassis full of working nonConfiguration Control modules, the modules will stop using the DIP Switch
settings and start using the Management Module settings. When a module
changes from DIP Switch settings to Management Module settings, the traffic
across the modules will drop for a very short period of time.
When removing an existing module and replacing it with a different type of
module, the configuration of the existing module remains.
Configuration Control had three goals when it was created:
1.
Without Configuration Control

-
The DIP Switches are ignored and the module takes the configuration from
the Management Module. This could be the default configuration or from a
previously installed module.
With Configuration Control

If the module is different (model or DIP Switch settings) from the module
installed in the slot previously, then the DIP Switch settings are used for
configuration. This configuration is then copied up to the Management
Module.

If the module is exactly the same (model and DIP Switch settings) to the
module previously installed, the current module will use the settings from
the management module.
Inserting a Management Module
Any type of module or Management Module, could be swapped out under
power with out losing any configuration.
2
3
-
-
Without Configuration Control
Unmanaged Modules

Before installing, configure the iMcV-10G-Converter modules for desired features.
The DIP Switch settings enable the end user to select the speed/protocol, loopback
modes and Loss Carry Forward (LCF). The table below indicates the available features
and settings for the iMcV-10G-Converter modules.
Modules in an unmanaged chassis use DIP Switch settings. When the
Management Module is inserted, the modules use the configuration stored
in the Management Module. This will more then likely change the
configuration of the modules, and will cause a short interruption in data
flowing through the modules.
With Configuration Control

Switch
The modules copy their configuration up to the Management Module. The
modules keep working, with no configuration change and no interruption in
data.
1
2
Removing a Management Module / Failed Management Module
-
Without Configuration Control

-
Modules previously configured by the Management Module will revert back
to their DIP Switch settings. This will more than likely change the
configuration, based on default settings and will cause an interruption in
data flow.
5,4,3
With Configuration Control

The modules continue to use whatever configuration they were set to. They
maintain a local copy of the configuration.

The SNMP Write Lock switch does not impact any of the iMcV-Modules
with Configuration Control.

If there is a mixture of iMcV-Modules with and without Configuration
Control, the Write Lock Switch and a new Management Module must be
taken into consideration.

If the command cleandb is applied to a Management Module, all the
settings for the modules it maintains will be removed, but the Configuration
Control modules will still be based on the last change made, while those
without Configuration Control will be set to their default settings.
6
7
8
Function
“ON” to Enable LOS from XFP1 to XFP2
“ON” to Enable LOS from XFP2 to XFP1
5
4
3
Combination of settings
OFF OFF OFF Use Internal clock
OFF ON OFF OC-192 SONET/SDH (9.95 Gb/S)
OFF OFF ON 10G Ethernet (10.32 Gb/S)
OFF ON ON 10G Fibre Channel (10.52 Gb/S)
ON
OFF OFF ITU G-709 OUT-2 (10.70)
ON
OFF ON 10G Ethernet G.702 (11.09Gb/S)
ON
ON OFF
N.A. (default 0,0,0)
ON
ON ON
“ON” to enable FAULT on DDMI alarm
Enable Loopback XFP1
Enable Loopback XFP2
* iMcV-Modules will be referred to as modules
4
5
Default
OFF
OFF
OFF/OFF/
OFF
(Ethernet)
OFF
OFF
OFF
Loss Carry Forward (LCF)
LED Operation
When a fault is detected on the incoming optical line that would severely affect the
quality of the corresponding output optical signal, this signal is turned OFF as
opposed to sending a bad optical signal to the next unit over the optical line. The
Loss Carry Forward function provides a very positive fault indication to the
downstream unit.
Each iMcV-10G-Converter features diagnostic LEDs that provide information on
features and ports.
If the LCF function is not enabled, the transmitted optical signal is dependent on the
XFP units installed. This fault indication may become very intermittent depending on
the actual optical signal level.
XFP Loopback
XFP Loopback is based on what the XFP module is capable of. There are 2 types of
loopback that an XFP has the potential to do: Lineside Loopback (red) and XFI
Loopback (blue). (If an OEM XFP is not capable of loopback, the SNMP Management
Module will provide notification of this status.)
Name
Color
Function
FLT
Yellow
ON When a DDMI fault is detected
LOS
Red
ON when the Optical LINK is good
LCF
Green
ON when no link is detected
LB
Yellow
ON when Loopback is enabled and “Blinks”
if the XFP can’t support this function when it
has been requested.
If an XFP is capable of Lineside Loopback, that is the type of loopback that will be
used. Lineside Loopback should be enabled on XFP1 OR XFP2. However, if both
XFP1 and XFP2 are enabled via the DIP Switches, XFP1 as the primary XFP will
support the task of Lineside Loopback. In addition, if just one port has an XFP
installed in it, and the other remains unoccupied, the loopback is still functional.
XFI Loopback has a different set of requirements. First, both XFP ports must be
installed for it to function. If an end user wants to perform a loopback on XFP1, and
it is not capable of Lineside Loopback, it must verify that XFP2 can do XFI Loopback,
and a message ‘not capable’ will be displayed. By following the receive signal on
XFP1, it goes through the XFP1 to XFP2 where it loops it back to the transmit signal of
XFP1.
If an end user enables loopback on both XFPs that are capable of XFI Loopback,
loopback is allowed on XFP1 and ‘not capable’ on XFP2. The loopback LED on XFP2
will blink to indicate this status.
6
7
Specifications
B&B Electronics Technical Support
Power Consumption (Typical @ 5V):
Tel: (800) 346-3119 (in the U.S. and Canada)
637mA @ +70C
Monday-Friday, 7:00am-7”00pm CST
Operating Temperature
+353 91 792444 (Europe)
-4°F to +158°F (-20°C to +70°C)
Monday through Friday 8:00am - 5:00pm GMT
Storage Temperature
Fax: (815) 433-5109 U.S. and Canada
-40°F to +185°F (-40°C to +85°C)
+353 91-79244S5 Europe
Humidity
5 to 95% (non-condensing); 0 to 10,000 ft. altitude
Dimensions
E-Mail: [email protected] U.S. and Canada
[email protected] Europe
Web: www.bb-elec.com
Dual-wide iMcV-module
8
9
Fiber Optic Cleaning Guidelines
Electrostatic Discharge Precautions
Fiber Optic transmitters and receivers are extremely susceptible to contamination by
particles of dirt or dust, which can obstruct the optic path and cause performance
degradation. Good system performance requires clean optics and connector ferrules.
Electrostatic discharge (ESD) can cause damage to any product, add-in modules or
stand alone units, containing electronic components. Always observe the following
precautions when installing or handling these kinds of products
1.
1.
Do not remove unit from its protective packaging until ready to install.
2.
Wear an ESD wrist grounding strap before handling any module or component.
If the wrist strap is not available, maintain grounded contact with the system unit
throughout any procedure requiring ESD protection.
3.
Hold the units by the edges; do not touch the electronic components or gold
connectors.
4.
After removal, always place the boards on a grounded, static-free surface, ESD
pad or in a proper ESD bag. Do not slide the modules or stand alone units over
any surface.
2.
Use fiber patch cords (or connectors, if you terminate your own fiber) only from
a reputable supplier; low-quality components can cause many hard-to-diagnose
problems in an installation.
Dust caps are installed at B&B Electronics to ensure factory-clean optical devices.
These protective caps should not be removed until the moment of connecting
the fiber cable to the device. Should it be necessary to disconnect the fiber
device, reinstall the protective dust caps.
3.
Store spare caps in a dust-free environment such as a sealed plastic bag or box so
that when reinstalled they do not introduce any contamination to the optics.
4.
If you suspect that the optics have been contaminated, alternate between
blasting with clean, dry, compressed air and flushing with methanol to remove
particles of dirt.
10
WARNING! Integrated circuits and fiber optic components are
extremely susceptible to electrostatic discharge damage. Do not
handle these components directly unless you are a qualified service
technician and use tools and techniques that conform to accepted
industry practices.
11
Certifications
CE:
The products described herein comply with the Council Directive on
Electromagnetic Compatibility (2004/108/EC) For further details,
contact B&B Electronics.
Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1, Appareil A’Laser de Classe 1
International Headquarters
B&B Electronics
707 Dayton Road
Ottawa, IL 61350 USA
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this
symbol on product or packaging must not be disposed of with unsorted municipal
waste. This symbol indicates that the equipment should be disposed of separately
from regular household waste. It is the consumer’s responsibility to dispose of this
and all equipment so marked through designated collection facilities appointed by
government or local authorities. Following these steps through proper disposal and
recycling will help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please contact
local authorities, waste disposal services, or the point of purchase for this equipment.
Phone (815) 433-5100 — General Fax (815) 433-5105
Email: [email protected]
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 — Fax +353 91-79244S5
Email: [email protected]
Website: www.bb-elec.com
© 2013 B&B Electronics. All rights reserved.
The information in this document is subject to change without notice. B&B Electronics assumes no responsibility for any
errors that may appear in this document. iMcV-10G-Converter XFP/XFP is a trademark of B&B Electronics. Other brands
or product names may be trademarks and are the property of their respective companies.
Document Number 60-80103-00 A1
12
October 2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement