Datasheet - Cyrix-i 120A-225A - rev 00

Datasheet - Cyrix-i 120A-225A - rev 00
Cyrix-i 12/24V 120A and 225A
www.victronenergy.com
Intelligent battery combiner
Intelligent battery monitoring to prevent unwanted switching
Some battery combiners (also called voltage controlled relay, or split charge relay) will disconnect a battery in case of a
short but high amperage load. A battery combiner also may fail to connect a large but discharged battery bank because
the DC voltage immediately drops below the disengage value once the batteries are connected.
The software of the Cyrix-i 12/24 does more than simply connect and disconnect based on battery voltage and with a
fixed time delay. The Cyrix-i 12/24 looks at the general trend (voltage increasing or decreasing) and reverses a previous
action only if the trend has reversed during a certain period of time. The time delay depends on the voltage deviation
from the trend.
(for Battery Combiners with multiple engage/disengage profiles, please see the Cyrix-i 200A-400A)
12/24V auto ranging
The Cyrix-i 12/24 automatically detects system voltage.
No voltage loss
Cyrix battery combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no
voltage loss so that the output voltage of alternators or battery chargers does not need to be increased.
Cyrix-i 12/24-120
Prioritising the starter battery
In a typical setup the alternator is directly connected to the starter battery. The accessory battery, and possibly also a
bow thruster and other batteries are each connected to the starter battery with Cyrix battery combiners. When a Cyrix
senses that the starter battery has reached the connect voltage it will engage, to allow for parallel charging of the other
batteries.
Bidirectional voltage sensing and power supply from both batteries
The Cyrix senses the voltage of both connected batteries. It will therefore also engage if for example the accessory
battery is being charged by a battery charger.
The Cyrix-i 12/24 has a dual power supply. It will therefore also close if the voltage on one battery is too low to operate
the Cyrix.
In order to prevent unexpected operation during installation or when one battery has been disconnected, the Cyrix-i
12/24 will not close if the voltage on one of the two battery connections is lower than 2V (12V battery) or 4V (24V
battery).
Parallel connection in case of emergency (Start Assist)
The Cyrix can also be engaged with a push button (Cyrix remains engaged during 30 seconds) or a switch to connect
batteries in parallel manually.
This is especially useful in case of emergency when the starter battery is discharged or damaged.
Cyrix-i 12/24-225
Cyrix battery combiner
Continuous current
Cranking rating (5 seconds)
Connect voltage
Disconnect voltage
Current consumption when open
Start Assist
Protection category
Weight kg (lbs)
Dimensions h x w x d in mm
(h x w x d in inches)
Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands
General phone: +31 (0)36 535 97 00 | Fax: +31 (0)36 535 97 40
E-mail: [email protected] | www.victronenergy.com
Cyrix-i 12/24-120
Cyrix-i 12/24-225
120 A
225 A
180 A
500 A
From 13V to 13,8V and 26 to 27,6V
with intelligent trend detection
From 11V to 12,8V and 22 to 25,7V
with intelligent trend detection
<4 mA
Yes (Cyrix remains engaged during 30 seconds)
IP54
0,11 (0.24)
0,66 (1.45)
46 x 46 x 80
100x90x100
(1.8 x 1.8 x 3.2)
(4.0x3.5x4.0)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement