Amana AMV9 Technical information

Amana AMV9 Technical information
TECHNICAL INFORMATION MANUAL
AMV9/ACV9
40" 90% Gas Furnace Units
Model and manufacturing numbers
listed on page 3.
• Refer to Service Manual RS6300003 Rev. 1 for installation, operation, and troubleshooting information.
• All safety information must be followed as provided in
the Service Manual.
• Refer to the appropriate Parts Catalog for part number
information.
®
C
This manual is to be used by qualified HVAC technicians only. Goodman
does not assume any responsibility for property damage or personal injury
due to improper service procedures performed by an unqualified person.
is a trademark of Maytag Corporation and is used under license to Goodman
Company, L.P. All rights reserved.
®
US
RT6612008 Rev. 1
December 2004
Copyright © 2004 Goodman Company, L.P.
PRODUCT IDENTIFICATION
The model and manufacturing number are used for positive identification of component parts used in manufacturing.
Please use these numbers when requesting service or parts information.
A
M
V
9
045 5
B X
A
Product Type
Design Series
G: Gas Furnace
A: Initial Release
Additional Features
Supply Type
C: Counterflow/Horizontal
M: Upflow/Horizontal
N: Natural Gas
X: Low NOx
Cabinet Width
A: 14"
Furnace Type
B: 17 1/2"
V: Variable Speed - 2 Stage Condensing (90%)
C: 21"
D: 24 1/2"
Model Family
9: Air Command 90 (40" Height)
Airflow Capability
3: 1200
4: 1600
5: 2000
Nominal Input
045:
45,000 Btuh
070:
70,000 Btuh
090:
90,000 Btuh
115:
115,000 Btuh
WARNING
IF REPAIRS ARE ATTEMPTED BY UNQUALIFIED PERSONS, DANGEROUS CONDITIONS (SUCH AS EXPOSURE TO ELECTRICAL SHOCK) MAY
RESULT. THIS MAY CAUSE SERIOUS INJURY OR DEATH.
GOODMAN WILL NOT BE RESPONSIBLE FOR ANY INJURY OR PROPERTY DAMAGE ARISING FROM IMPROPER SERVICE OR SERVICE PROCEDURES. IF YOU PERFORM SERVICE ON YOUR OWN PRODUCT, YOU ASSUME RESPONSIBILITY
FOR ANY PERSONAL INJURY OR PROPERTY DAMAGE WHICH MAY RESULT.
CAUTION
2 Rev. 1
PRODUCT IDENTIFICATION
The model and manufacturing number are used for positive identification of component parts used in manufacturing.
Please use these numbers when requesting service or parts information.
MODEL
M/N
AMV90453BXA P1257401F
MODEL
ACV90704CXA
M/N
P1257703F
AMV90704CXA P1257403F
ACV90905DXA
P1257705F
AMV90905DXA P1257405F
AMV91155DXA P1257406F
3 Rev. 1
PRODUCT DESIGN
General Operation
The AMV9 and ACV9 furnaces are equipped with an electronic ignition device to light the burners and an induced
draft blower to exhaust combustion products.
An interlock switch prevents furnace operation if the blower
door is not in place. Keep the blower access doors in place
except for inspection and maintenance.
This furnace is also equipped with a self-diagnosing electronic control module. In the event a furnace component is
not operating properly, the control module LED will flash on
and off in a factory-programmed sequence, depending on
the problem encountered. This light can be viewed through
the observation window in the blower access door. Refer to
the Troubleshooting Chart for further explanation of the LED
codes and Abnormal Operation - Integrated Ignition Control section in the Service Instructions for an explanation of
the possible problem.
The rated heating capacity of the furnace should be greater
than or equal to the total heat loss of the area to be heated.
The total heat loss should be calculated by an approved
method or in accordance with “ASHRAE Guide” or “Manual
J-Load Calculations” published by the Air Conditioning Contractors of America.
*Obtain from: American National Standards Institute 1430
Broadway New York, NY 10018
Location Considerations
•
The furnace should be as centralized as is practical
with respect to the air distribution system.
•
Do not install the furnace directly on carpeting, tile,
or combustible material other than wood flooring.
•
When suspending the furnace from rafters or joists,
use 3/8" threaded rod and 2” x 2” x 1/8” angle as
shown in the Installation and Service Instructions. The
length of the rod will depend on the application and
clearance necessary.
When installed in a residential garage, the furnace
must be positioned so the burners and ignition source
are located not less than 18 inches (457 mm) above
the floor and protected from physical damage by vehicles.
Notes:
4. Installer must supply the following gas line fittings, depending on which entrance is used:
Left -- Two 90° Elbows, one close nipple, straight pipe
Right -- Straight pipe to reach gas valve.
Accessibility Clearances (Minimum)
AMV9 MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
(INCHES)
POSITION* FRONT SIDES REAR
TOP
FLUE FLOOR
Upflow
3
0
0
1
0
C
Horizontal
3
6
0
6
0
C
*=
All positioning is determined as installed unit is viewed from the front.
C= If placed on combustible floor, floor MUST be wood only.
NC= For instalaltion on non-combustible floors only. A combustible
subbase must be used for installations on combustible flooring.
ACV9 MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
(INCHES)
POSITION* FRONT SIDES REAR
TOP
FLUE FLOOR
Upflow
3
0
0
1
0
NC
Horizontal
3
6
0
6
0
C
*=
All positioning is determined as installed unit is viewed from the front.
C= If placed on combustible floor, floor MUST be wood only.
NC= For instalaltion on non-combustible floors only. A combustible
subbase must be used for installations on combustible flooring.
36" at front is required for servicing or cleaning.
Note: In all cases accessibility clearance shall take precedence over clearances from the enclosure where accessibility clearances are greater. All dimensions are given in
inches.
High Altitude Derate
When this furnace is installed at high altitude, the appropriate High Altitude orifice kit must be installed. This is required due to the natural reduction in the density of both
the gas fuel and combustion air as altitude increases. The
kit will provide the proper design certified input rate within
the specified altitude range.
•
1. Installer must supply one or two PVC pipes: one for
combustion air (optional) and one for the flue outlet (required). Vent pipe must be either 2” or 3” in diameter,
depending upon furnace input, number of elbows, length
of run and installation (1 or 2 pipes). The optional Combustion Air Pipe is dependent on installation/code requirements and must be 2” or 3” diameter PVC.
2. Line voltage wiring can enter through the right or left
side of the furnace. Low voltage wiring can enter through
the right or left side of furnace.
3. Conversion kits for propane gas and high altitude natural and propane gas operation are available. See High
Altitude Derate chart for details.
4 Rev. 1
"STANDARD" and "HIGH ALTITUDE" KITS
0 - 7,000 Feet
(Standard Altitude)
7,001 - 9,000 Feet
9,001 - 11,000 Feet
Natural
Propane
ID Blwr
Pressure
Switch
AMV90453BXA
AMV90704CXA
No
Change
LPM-03
#55 Orifice
No
Change
HANG13
HALP11
#44
HAPS28
#56 Orifice
Orifice
HANG14
#45
Orifice
HALP11
#56
Orifice
HAPS28
AMV90905DXA
AMV91155DXA
No
Change
LPM-03
#55 Orifice
No
Change
HANG13
#44
Orifice
HALP11
#56
Orifice
HAPS29
HANG14
#45
Orifice
HALP11
#56
Orifice
HAPS29
ACV90704CXA
ACV90905DXA
No
Change
LPM-03
#55 Orifice
No
Change
HANG13
#44
Orifice
HALP11
#56
Orifice
HAPS29
HANG14
#45
Orifice
HALP11
#56
Orifice
HAPS31
Furnace
Gas Orifices
Gas Orifices
Natural
Propane
ID Blwr
Pressure
Switch
Natural
Propane
Gas Orifices
ID Blwr
Pressure
Switch
High altitude kits are purchased according to the installation altitude and usage of either natural or propane gas.
Refer to the chart above for a tabular listing of appropriate
altitude ranges and corresponding manufacturer’s high altitude Natural Gas and Propane Gas kits. For a tabular listing of appropriate altitude ranges and corresponding
manufacturer's High Altitude Pressure Switch kits, refer to
either the Pressure Switch Trip Points & Usage Chart in
this manual or the Accessory Charts in Service Instructions.
COMPONENT IDENTIFICATION
8
7
7
5
9 10
27
28
BURNER COMPARTMENT
33
4
3
13
*
*
12
*
*
*
*
*
15
18
17
19
31 32
30
19
20
BLOWER COMPARTMENT
20
25
26
14
16
*
*
1
11
11
3
2
10
BLOWER COMPARTMENT
6
29
24
3
3
23
16
32
18
21
30
22
12
21
15
17
31
CFM
87
4321
87
4321
OFF
ON
S4
10
7
11
8
4
5
1
2
CUT FOR
DEHUM
S3
12
19
9
6
3
20
21
Intell-Ignition
TWO
WR
TSTAT
SINGLE
29
ON
C
S1
3
2
1
OFF
23
20
21
US
24
26
28
19
27
Upflow/Horizontal
14
13
2 22
9
25
7
8
7 6 4
1
Counterflow /Horizontal
1
Two-Stage Gas Valve
19 Coil Front Cover Pressure Tap
2
Gas Line Entrance (Alternate)
20 Coil Front Cover Drain Port
3
Pressure Switch(es)
21 Drain Line Penetrations
4
Gas Manifold
22 Drain Trap
5
Combustion Air Intake Connection
23 Blower Door Interlock Switch
6
Hot Surface Igniter
24 Inductor (Not All Models)
7
Rollout Limit
25 Two-Stage Integrated Control Module
8
Burners
9
Flame Sensor
(with fuse and diagnostic LED)
26 24 Volt Thermostat Connections
10 Flue Pipe Connection
27 Transformer (40 VA)
11 Flue Pipe
28 ECM Variable Speed Circulator Blower
12 Combustion Air Intake (Alternate)
29 Bottom Return Filter Retainer
13 Primary Limit
30 Auxiliary Limits
14 Gas Line Entrance
31 Junction Box
15 Flue Pipe Connection (Alternate)
32 Electrical Connection Inlets
16 Rubber Elbow
33 Coil Front Cover
17 Two-Speed Induced Draft Blower
34 Combustion Air Inlet Pipe (ACV9 Only)
18 Electrical Connection Inlets (Alternate)
AMV9_____XA (Manufacturing Numbers P1257401-06F)
ACV9_____XA (Manufacturing Numbers P1257703-05F)
5 Rev. 1
BURNER COMPARTMENT
5
PRODUCT DIMENSIONS
AMV9___XA
AIR
DISCHARGE
A
28 3/4
B
(DISCHARGE AIR)
C
3/4
3/4
2 1/2
20 3/16
AIR INTAKE PIPE
2" PVC
ALTERNATE
GAS SUPPLY
HOLE
LEFT SIDE
DRAIN LINE
HOLES
2 1/16
DRAIN
TRAP
CL
30 1/4
CONDENSATE
DRAIN TRAP
w/ 3/4" PVC
DISCHARGE
(RIGHT OR
LEFT SIDE)
40
LOW VOLTAGE
ELECTRICAL HOLE
HIGH VOLTAGE
ELECTRICAL HOLE
SIDE CUT-OUT
ALTERNATE
VENT/FLUE
LOCATION
4 1/8
27 1/8
6 1/8
30 1/4
19 3/16
2 5/8
19 3/16
2
1 3/4
ALTERNATE
AIR INTAKE LOCATION
STANDARD GAS
SUPPLY HOLE
2 11/16
23
14
VENT/FLUE PIPE
2" PVC
7 3/8
2 5/8
AIR
DISCHARGE
3/4
HIGH VOLTAGE
ELECTRICAL HOLE
11 3/4
16 5/8
11 3/4
9 3/8
RIGHT SIDE
DRAIN LINE
DRAIN
HOLES
TRAP
CL
LOW VOLTAGE
ELECTRICAL HOLE
32 13/16
7 7/8
1 3/4
SIDE CUT-OUT
1 5/8
1 1/2
D
BOTTOM KNOCK-OUT
23 9/16
BOTTOM KNOCK-OUT
RIGHT SIDE
VIEW
FRONT
VIEW
LEFT SIDE
VIEW
CABINET
SIZE
UNITS
A
B
C
D
SMALL
0453BXA
17 1/2
15
12 3/8
12 5/8
21
19
16 3/8
14 5/8
24 1/2
23
20 3/8
18 5/8
MEDIUM 0704CXA
LARGE
0905DXA
1155DXA
All dimensions are in inches.
AMV9_____XA (Manufacturing Numbers P1257401-06F)
6 Rev. 1
PRODUCT DIMENSIONS
ACV9_____XA
LEFT SIDE
VIEW
FRONTVIEW
28 3/4
3/4
RIGHT SIDE
VIEW
A
2 1/2
AIR INTAKE PIPE
2" PVC
20 1/4
3/4
3/4
B
(RETURN AIR)
CONDENSATE
DRAIN TRAP
w/ 3/4" PVC
DISCHARGE
(RIGHT OR
LEFT SIDE)
1 3/4
LOW VOLTAGE
ELECTRICAL HOLE
VENT/FLUE PIPE
2" PVC
2 1/16
40
HIGH VOLTAGE
ELECTRICAL HOLE
ALTERNATE
VENT/FLUE
LOCATION
6 1/8
28 5/16
28 5/16
LOW VOLTAGE
ELECTRICAL HOLE
1 3/4
HIGH VOLTAGE
ELECTRICAL HOLE
ALTERNATE
AIR INTAKE LOCATION
2 11/16
19 7/8
LEFT SIDE
DRAIN LINE
HOLES
DRAIN
DRAIN
TRAP 2 5/8
CL
STANDARD GAS
SUPPLY HOLE
2 5/8 TRAP
C
L
RIGHT SIDE
DRAIN LINE
HOLES
18 13/16
15 1/2
4 1/8
14
2
11 1/2
9 13/16
11 5/8
8 1/4
18 5/8
UNFOLDED FLANGES
20 5/32
FOLDED FLANGES
9 3/4
7 3/8
ALTERNATE GAS
SUPPLY HOLE
D
UNFOLDED FLANGES
E
FOLDED FLANGES
AIR
DISCHARGE
AIR
DISCHARGE
DISCHARGE AIR
CABINET
SIZE
UNITS
MEDIUM 0704CXA
LARGE
0905DXA
A
B
C
D
21
19
16 3/8
14 5/8
24 1/2
23
20 3/8
18 5/8
All dimensions are in inches.
ACV9___BX__ (Manufacturing Numbers P1257703-05F)
7 Rev. 1
PRODUCT DESIGN
PRESSURE SWITCH TRIP POINTS AND USAGE CHART
MODEL
AMV90453BXA
AMV90704CXA
AMV90905DXA
AMV91155DXA
ACV90704CXA
ACV90904DXA
NEGATIVE
PRESSURE
ID BLOWER
WITH FLUE
NOT FIRING
TYPICAL SEA
LEVEL DATA
NEGATIVE
PRESSURE
ID BLOWER
WITH FLUE
FIRING
TYPICAL SEA
LEVEL DATA
NEGATIVE
PRESSURE
COIL COVER
WITH FLUE
NOT FIRING
TYPICAL SEA
LEVEL DATA
NEGATIVE
PRESSURE
COIL COVER
WITH FLUE
FIRING
TYPICAL SEA
LEVEL DATA
LOW
FIRE
HIGH
FIRE
LOW
FIRE
HIGH
FIRE
LOW
FIRE
HIGH
FIRE
LOW
FIRE
HIGH
FIRE
-0.45
-0.90
-0.50
-0.95
-0.25
-0.25
-0.25
-0.25
-0.65
-1.20
-0.70
-1.25
-0.25
-0.25
-0.25
-0.25
-0.35
-0.35
-0.35
-0.70
-0.70
-0.40
-0.75
-0.75
-0.52
-0.52
-0.52
-0.52
-0.52
-0.52
-0.52
-0.52
Note: The typical sea level negative pressure data represents the minimum pressures
expected. Shorter length of flue pipe or single pipe systems compared to dual pipe systems
should show higher (greater negative) pressures.
PRESSURE SWITCH TRIP POINTS AND USAGE CHART
0 to 7,000 ft.
MODEL
TRIP POINT
COIL COVER
PRESSURE
SWITCH
LOW
HIGH
FIRE
FIRE
COIL COVER
PRESSURE
SWITCH
PART #
TRIP POINT
ID BLOWER
PRESSURE
SWITCH
LOW
HIGH
FIRE
FIRE
7,001 ft. to 11,000 ft.
ID BLOWER
PRESSURE
SWITCH
PART #
PS1
LABEL
COLOR
PS2
LABEL
COLOR
TRIP POINT
COIL COVER
PRESSURE
SWITCH
LOW
HIGH
FIRE
FIRE
TRIP POINT
ID BLOWER
PRESSURE
SWITCH
LOW
HIGH
FIRE
FIRE
HIGH
ALTITUDE
KIT
PS1
LABEL
COLOR
PS2
LABEL
COLOR
AMV90453BXA
AMV90704CXA
-0.10
-0.10
20197301
-0.30
-0.75
11177113
PURPLE
PINK
-0.10
-0.10
-0.22
-0.55
HAPS28
11177115
GREEN
YELLOW
AMV90905DXA
AMV91155DXA
-0.10
-0.10
20197301
-0.50
-1.10
11177114
WHITE
GRAY
-0.10
-0.10
-0.38
-0.82
HAPS29
11177116
ORANGE
LT BLUE
ACV90704CXA
-0.37
-0.37
20197306
-0.20
-0.55
11177118
GREEN
PURPLE
-0.37
-0.37
-0.15
-0.30
HAPS31
11177120
YELLOW
RED
ACV90905DXA
-0.37
-0.37
20197306
-0.20
-0.55
11177118
GREEN
PURPLE
-0.37
-0.37
-0.15
-0.30
HAPS31
11177120
YELLOW
RED
Note: All installations above 7,000 ft. require a pressure switch change. For installations in Canada the AMV9 & ACV9 furnaces are certified only to 4500 ft.
Note: Replacement pressure switch number is listed below high altitude kit number.
Note: All negative pressure readings are in inches of water column (" w.c.).
T.O.D. PRIMARY LIMIT
Part Number
8 Rev. 1
20162903 20162905 20162907 20162908
Open Setting (°F)
Color Code(s)
AMV90453BXA
AMV90704CXA
AMV90905DXA
AMV91155DXA
160
Blue
ACV90704CXA
ACV90905DXA
1
145
Yellow
1
155
Orange
170
Green
1
1
1
1
PRODUCT DESIGN
ROLLOUT LIMIT SWITCHES
Part Number
10123517
10123518
10123533
10123537
Open Setting (°F)
Color Code(s)
AMV90453BXA
AMV90704CXA
AMV90905DXA
AMV91155DXA
210
White
170
Blue
1
200
Yellow
190
Gray
ACV90704CXA
ACV90905DXA
2
2
2
2
2
2
2
AUXILIARY LIMIT SWITCHES
Part Number
10123518
10123533
10123535
10123536
10123537
Open Setting (°F)
Color Code(s)
AMS90453BXA
AMS90703BXA
AMS90905DXA
AMS91155DXA
170
Blue
200
Yellow
150
Red
2
180
Lt. Blue
190
Gray
ACS90453BXA
ACS91155DXA
2
2
2
2
2
9 Rev. 1
PRODUCT DESIGN
Coil Matches:
A large array of Amana® brand coils are available for use with the new ACV9 furnaces, in either counterflow or horizontal
applications & with AMV9 furnaces, in either upflow or horizontal applications. These coils are available in both cased
and uncased models, with or without a TXV expansion device. These new 92%+ and 95%+ furnaces match up with the
existing Amana® brand coils as shown in the chart below.
Coil Matches (for Amana® brand units using R22):
CABINET
WIDTH
FURNACE
MODELS
17 1/2
AMV90453BXA
ACV90453BXA
21
AMV90704CXA
ACV90704CXA
1 1/2 - 4
AMS90905DXA
ACS90905DXA
AMS91155DXA
ACS91155DXA
2-5
24 1/2
CAUF
UNCASED
"A" COILS
CAUX
UNCASED
TXV "A" COILS
CACF
CASED
"A" COILS
CAPF
CASED
"A" COILS
CAUF018B2*
CAUF025B2*
CAUF030B2*
CAUF036B2*
CAUF037B2*
CAUF042B2*
CAUF048B2*
CAUX018B2*
CAUX025B2*
CAUX036B2*
CAUX037B2*
CAUX042B2*
CACF030B2*
CACF036B2*
CACF042B2*
CACF048B2*
CAPF018B2*
CAPF025B2*
CAPF030B2*
CAPF039B2*
CAPF036B2*
CAPF037B2*
CAPF042B2*
CAPX018B2*
CAPX025B2*
CAPX030B2*
CAPX036B2*
CAPX037B2*
CAPX042B2*
CHPF036B2*
CHPF042B2*
CHPF048B2*
CHPX036B2*
CHPX042B2*
CAUF042C2*
CAUF048C2*
CAUF049C2*
CAUF060C2*
CAUF061C2*
CAUX049C2*
CACF042C2*
CACF048C2*
CACF060C2*
CACF061C2*
CAPF036C2*
CAPF042C2*
CAPX049C2*
CHPF048D2*
CHPF060D2*
CHPX048D2*
CHPX060D2*
CAUF049D2*
CAUF060D2*
CAUF061D2*
CAUX049D2*
CAUX060D2*
CAUX061D2*
CACF060D2*
CACF061D2*
CAPF049D2*
CAPF060D2*
CAPX049D2*
CAPX060D2*
CAPX061D2*
CHPF048D2*
CHPF060D2*
CHPX048D2*
CHPX060D2*
AIRFLOW
(tons)
1 1/2 - 3
CAPX
CHPF
CHPX
CASED
HORIZ. CASED HORIZ. CASED
TXV "A" COILS
"A" COIL
TXV "A" COIL
Coil Matches (for the Amana RSD units using R-410A):
AIRFLOW
(tons)
CAUF
UNCASED
"A" COILS
CAUX
UNCASED
TXV "A" COILS
CAPF
CASED
"A" COILS
17 1/2
AMV90453BXA
ACV90453BXA
1 1/2 - 3
CAUF030B4*
CAUF036B4*
CAUX030B4*
CAUX036B4*
CAUX042B4*
CAPF030B4*
CAPF036B4*
CAPX030B4*
CAPX036B4*
AMV90704CXA
ACV90704CXA
1 1/2 - 4
CAUX042C4*
CAUX048C4*
CAUX057D4*
CAUX060D4*
CAPF042C4*
21
CAPX042C4*
CAPX048C4*
24 1/2
AMV90905DXA
ACV90905DXA
AMV91155DXA
ACV91155DXA
2-5
CAUX057D4*
CAUX060D4*
CAPF057D4*
CAPF060D4*
CAPX057D4*
CAPX060D4*
CABINET
WIDTH
FURNACE
MODELS
10 Rev. 1
CAUF042C4*
CAUF048C4*
CAUF057D4*
CAPX
CHPF
CHPX
CASED
HORIZ. CASED HORIZ. CASED
TXV "A" COILS
"A" COIL
TXV "A" COIL
CHPF036B4*
CHPX036B4*
CHPF048D4*
CHPF060D4*
CHPX048D4*
CHPX060D4*
PRODUCT DESIGN
Thermostats:
The following Amana® brand thermostats are suggested for use with AMV9 & ACV9 Furnace Models:
THERMOSTATS
Thermostat
Man/Auto
Programmable
Cool Heat Batt. Powered Batt. Bkup
1213406*
Man. Or Auto
Yes
2
3
No
No
1213407
Man. Changeover
Yes
2
2
Yes
Yes
1213411
Man. Changeover
No
2
2
Yes
No
*1213406 is the recommended model for the AMV9 & ACV9 furnaces when used with a heat pump in a fossil fuel
application. It is NOT for use with either the AMV9 or ACV9 as a sole heating source. 1213406 thermstats are 24V
powered with battery backup.
Filters:
Filters are required with this furnace and must be provided by the installer. The filters used must comply with UL900 or
CAN/ULCS111 standards. Installing this furnace without filters will void the unit warranty
Upflow Filters
This furnace has provisions for the installation of return air filters at the side and/or bottom return. The furnace will
accommodate the following filter sizes depending on cabinet size:
SIDE RETURN
Approx.
Cabinet
Nominal
Width
Filter Size Flow Area
(in.)
(in.)
(in2)
All
16 x 25 x 1
400
BOTTOM RETURN
Approx.
Cabinet
Nominal
Width
Filter Size Flow Area
(in.)
(in.)
(in2)
17-1/2
14 x 25 x 1
350
21
16 x 25 x 1
400
24-1/2
20 x 25 x 1
500
Refer to Minimum Filter Area tables to determine filter area requirement. NOTE: Filters can also be installed elsewhere
in the duct system such as a central return.
UPFLOW
COOLING AIRFLOW REQUIREMENT (CFM)
600
800
1000
1200
1400
1600
2000
0453__XA
376*
384
480
576
---
---
---
0704__XA
---
---
564*
564*
672
768
0905__XA
---
---
---
752*
752*
768
960
1155__XA
---
---
---
940*
940*
940*
960
Input__Airflow
Input__Airflow
UPFLOW
COOLING AIRFLOW REQUIREMENT (CFM)
600
800
1000
1200
1400
1600
2000
0453__XA
376*
384
480
576
---
---
---
0704__XA
---
---
627*
627*
672
768
---
0905__XA
---
---
---
836*
836*
836*
960
1155__XA
---
---
---
940*
940*
940*
960
COUNTERFLOW
COOLING AIRFLOW REQUIREMENT (CFM)
600
800
1000
1200
1400
1600
2000
0704__XA
---
---
641*
641*
672
768
---
0905__XA
---
---
---
854*
854*
854*
960
Input
Airflow
Input
Airflow
COUNTERFLOW
COOLING AIRFLOW REQUIREMENT (CFM)
600
800
1000
1200
1400
1600
2000
0704__XA
---
---
320*
320*
336
384
---
0905__XA
---
---
---
427*
427*
427*
480
*Minimum filter area dictated by heating airflow requirement.
*Minimum filter area dictated by heating airflow requirement.
Disposable Minimum Filter Area (in2)
Permanent Minimum Filter Area (in2)
[Based on a 300 ft/min filter face velocity]
[Based on 600 ft/min filter face velocity]
11 Rev. 1
PRODUCT DESIGN
Counterflow Filters
This furnace has provisions for the installation of return air filters at the counterflow top return. The furnace will
accommodate the following filter sizes depending on cabinet size:
Counterflow Top Return
Return Air
Cabinet Width
Optional
Access
Door
"A"
Min
17 1/2
21
24 1/2
17 1/2
21
24 1/2
17 1/2
21
24 1/2
Filter Area Qty Filter Size Dimension "A"
2
(in)
(in)
(in )
600
2
15 X 20 X 1
800
2
20 X 20 X 1
1000
2
25 X 20 X 1
14.2
13.0
11.3
19.7
18.8
17.7
25.0
24.3
23.4
Refer to Minimum Filter Area tables to determine filter area requirement. NOTE: Filters can also be installed elsewhere
in the duct system such as a central return.
12 Rev. 1
FURNACE SPECIFICATIONS
MODEL
AMV90453BXA
AMV90704CXA
AMV90905DXA
AMV91155DXA
Btuh Input (US) High Fire
46,000
69,000
92,000
115,000
Output (US) High Fire
44,300
66,900
88,800
111,100
Btuh Input (US) Low Fire
32,000
48,000
64,000
80,000
Output (US) Low Fire
30,800
46,400
61,700
77,400
96%
95.5%
95.7%
95.8%
Rated External Static (" w.c.)
.10 - .50
.10 - .50
.10 - .50
.10 - .50
Temperature Rise (°F)
30 - 60
30 - 60
30 - 60
35 - 65
High Stage Pressure Switch Trip Point (" w.c.)
-0.75
-0.75
-1.10
-1.10
Low Stage Pressure Switch Trip Point (" w.c.)
-0.30
-0.30
-0.50
-0.50
Front Cover Pressure Switch Trip Point (" w.c)
-0.10
-0.10
-0.10
-0.10
Blower Wheel (D" x W")
10 x 7
10 x 10
11 x 10
11 x 10
1/2
3/4
1
1
A.F.U.E.
Blower Horsepower
Blower Speeds
Refer to airflow charts on pages 15-19.
Max CFM @ 0.5 E.S.P.
Power Supply
115-60-1
115-60-1
115-60-1
115-60-1
10.4
12.8
14.6
14.6
15
15
15
15
Transformer (VA)
40
40
40
40
Heat Anticipator (Amps)
0.7
0.7
0.7
0.7
Primary Limit Setting (°F)
145
155
145
160
Auxiliary Limit Setting (°F)
150
190
180
200
Rollout Limit Setting (°F)
170
200
190
200
30 secs.
30 secs.
30 secs.
30 secs.
150 secs.
150 secs.
150 secs.
150 secs.
5 secs.
5 secs.
5 secs.
5 secs.
Off Cooling
45 secs.
45 secs.
45 secs.
45 secs.
Fan Delay On - Fan Only
5 secs.
5 secs.
5 secs.
5 secs.
7 / 11
7 / 11
7 / 11
7 / 11
Manifold Pressure (Natural/Propane) High Stage (" w.c.)
3.5 / 10
3.5 / 10
3.5 /10
3.5 /10
Manifold Pressure (Natural/Propane) Low Stage ("w.c.)
1.9 / 6.0
1.9 / 6.0
1.9 / 6.0
1.9 / 6.0
Orifice Size (Natural/Propane)
#43 / #55
#43 / #55
#43 / #55
#43 / #55
Number of Burners
2
3
4
5
Vent Connector Diameter (inches)
2
2
3
3
Combustion Air Connector Diameter (inches)
2
2
3
3
133
157
172
184
Minimum Circuit Ampacity (MCA)
Maximum Overcurrent Device
Fan Delay On Heating
Off Heating *
Fan Delay On Cooling
Gas Supply Pressure (Natural/Propane) (" w.c.)
Shipping Weight (lbs.)
* Off Heating - This fan delay timing is adjustable (90, 120, 150 or 180 seconds), 150 seconds as shipped.
1. These furnaces are manufactured for natural gas operation. Optional Kits are available for conversion to propane gas operation.
2. For elevations above 2000 ft. the rating should be reduced by 4% for each 1000 ft. above sea level. The furnace must not be
derated, orifice changes should only be made if necessary for altitude.
3. The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufactures method in
accordance with the "A.S.H.R.A.E. GUIDE" or "MANUAL J-LOAD CALCULATIONS" published by the AIR CONDITIONING
CONTRACTORS OF AMERICA. The total heat loss calculated should be equal to or less than the heating capacity. Output
based on D.O.E. test procedures, steady state efficiency times output.
4. Minimum Circuit Ampacity calculated as: (1.25 x Circulator Blower Amps) + I.D. Blower Amps.
13 Rev. 1
FURNACE SPECIFICATIONS
MODEL
ACV90704CXA
ACV90905DXA
Btuh Input (US) High Fire
69,000
92,000
Output (US) High Fire
65,300
86,500
Btuh Input (US) Low Fire
48,000
64,000
Output (US) Low Fire
45,000
60,100
A.F.U.E.
93.3%
92.7%
Rated External Static (" w.c.)
.10 - .50
.10 - .50
Temperature Rise (°F)
30 - 60
30 - 60
High Stage Pressure Switch Trip Point (" w.c.)
-0.55
-0.55
Low Stage Pressure Switch Trip Point (" w.c.)
-0.20
-0.20
Front Cover Pressure Switch Trip Point (" w.c)
-0.37
-0.37
10 x 10
11 x 10
3/4
1
Blower Wheel (D" x W")
Blower Horsepower
Blower Speeds
Max CFM @ 0.5 E.S.P.
Power Supply
Refer to airflow charts on pages
15-19.
115-60-1
115-60-1
12.8
14.6
15
15
Transformer (VA)
40
40
Heat Anticipator (Amps)
0.7
0.7
Primary Limit Setting (°F)
160
170
Auxiliary Limit Setting (°F)
220
180
Rollout Limit Setting (°F)
220
210
30 secs.
30 secs.
150 secs.
150 secs.
5 secs.
5 secs.
Off Cooling
45 secs.
45 secs.
Fan Delay On - Fan Only
5 secs.
5 secs.
7 / 11
7 / 11
Manifold Pressure (Natural/Propane) High Stage (" w.c.)
3.5 / 10
3.5 /10
Manifold Pressure (Natural/Propane) Low Stage ("w.c.)
1.9 / 6.0
1.9 / 6.0
Orifice Size (Natural/Propane)
#43 / #55
#43 / #55
Number of Burners
3
4
Vent Connector Diameter (inches)
2
2
Combustion Air Connector Diameter (inches)
2
2
157
172
Minimum Circuit Ampacity (MCA)
Maximum Overcurrent Device
Fan Delay On Heating
Off Heating *
Fan Delay On Cooling
Gas Supply Pressure (Natural/Propane) (" w.c.)
Shipping Weight (lbs.)
* Off Heating - This fan delay timing is adjustable (90, 120, 150 or 180 seconds), 150 seconds as shipped.
1. These furnaces are manufactured for natural gas operation. Optional Kits are available for conversion to propane gas operation.
2. For elevations above 2000 ft. the rating should be reduced by 4% for each 1000 ft. above sea level. The furnace must not be
derated, orifice changes should only be made if necessary for altitude.
3. The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufactures method in
accordance with the "A.S.H.R.A.E. GUIDE" or "MANUAL J-LOAD CALCULATIONS" published by the AIR CONDITIONING
CONTRACTORS OF AMERICA. The total heat loss calculated should be equal to or less than the heating capacity. Output
based on D.O.E. test procedures, steady state efficiency times output.
4. Minimum Circuit Ampacity calculated as: (1.25 x Circulator Blower Amps) + I.D. Blower Amps.
14 Rev. 1
BLOWER PERFORMANCE SPECIFICATIONS
AMV9 Heating Speed Charts
AMV90453BXA (Rise Range: 30 - 60°F)
Heating
Speed
Tap
A
B
C
D
AMV90704CXA (Rise Range: 30 - 60°F)
Adjust
Tap
Low Stage
CFM
at .1" - .5" w.c.
ESP
High Stage
CFM
at .1" - .5" w.c.
ESP
Rise
(°F)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
495
550
605
540
600
660
585
650
715
630
700
770
713
792
871
778
864
950
842
936
1030
907
1008
1109
57
51
46
52
47
43
48
43
39
45
40
36
Heating
Speed
Tap
A
B
C
D
AMV90905DXA (Rise Range: 30 - 60°F)
Heating
Speed
Tap
A
B
C
D
Adjust
Tap
Low Stage
CFM
at .1" - .5" w.c.
ESP
High Stage
CFM
at .1" - .5" w.c.
ESP
Rise
(°F)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
756
840
924
828
920
1012
900
1000
1100
972
1080
1188
1089
1210
1331
1192
1325
1457
1296
1440
1584
1400
1555
1711
56
50
46
51
46
42
47
42
38
43
39
35
AMV91155DXA (Rise Range: 30 - 60°F)
Adjust
Tap
Low Stage
CFM
at .1" - .5" w.c.
ESP
High Stage
CFM
at .1" - .5" w.c.
ESP
Rise
(°F)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
1013
1125
1238
1076
1195
1315
1139
1265
1392
1202
1335
1469
1458
1620
1782
1549
1721
1893
1639
1822
2004
1730
1922
2115
56
50
45
52
47
43
49
44
40
47
42
38
Heating
Speed
Tap
A
B
C
D
Adjust
Tap
Low Stage
CFM
at .1" - .5" w.c.
ESP
High Stage
CFM
at .1" - .5" w.c.
ESP
Rise
(°F)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
1107
1230
1353
1139
1265
1392
1170
1300
1430
1202
1335
1469
1594
1771
1948
1639
1822
2004
1685
1872
2059
1730
1922
2115
63
57
52
62
56
50
60
54
49
58
53
48
1. Units are shipped without filter(s). CFM in chart is without filter(s).
2. All furnaces shipped with heating speed set at "B" and cooling speed set at "D". Installer should adjust blower speed as needed.
The first task is to determine the proper aiflow for the cooling system.
3. For most cooling applications, about 400 CFM per ton is desirable.
4. The chart is for information only. For satisfactory operation, external static pressure not to exceed value shown on rating plate.
5. Do not operate above 0.5" w.c. ESP in heating mode. Operating between 0.5" w.c. and 0.8" w.c. is tabulated for cooling purposes only.
6. * Motor CFM minimum.
15 Rev. 1
BLOWER PERFORMANCE SPECIFICATIONS
AMV9 High (Single) Stage Cooling Speed Charts
AMV90453BXA
Cooling
Speed
Tap
A
B
C
D
AMV90704CXA
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
540
600
660
720
800
880
900
1000
1100
1080
1200
1320
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
540
600
660
720
800
880
990
1100
1210
1286
1429
1572
AMV90905DXA
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
720
800
880
990
1100
1210
1260
1400
1540
1620
1800
1980
AMV91155DXA
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
720
800
880
990
1100
1210
1260
1400
1540
1620
1800
1980
AMV9 Low Stage Cooling Speed Charts
AMV90453BXA
Cooling
Speed
Tap
A
B
C
D
AMV90704CXA
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
380*
390
429
468
520
572
585
650
715
702
780
858
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
378*
390
429
468
520
572
644
715
787
836
929
1022
AMV90905DXA
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
513*
520
572
644
715
787
819
910
1001
1053
1170
1287
AMV91155DXA
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
514*
520
572
644
715
787
819
910
1001
1053
1170
1287
1. Units are shipped without filter(s). CFM in chart is without filter(s).
2. All furnaces shipped with heating speed set at "B" and cooling speed set at "D". Installer should adjust blower speed
as needed. The first task is to determine the proper aiflow for the cooling system.
3. For most cooling applications, about 400 CFM per ton is desirable.
4. The chart is for information only. For satisfactory operation, external static pressure not to exceed value shown on
rating plate.
5. Do not operate above 0.5" w.c. ESP in heating mode. Operating between 0.5" w.c. and 0.8" w.c. is tabulated for
cooling purposes only.
6. * Motor CFM minimum.
16 Rev. 1
BLOWER PERFORMANCE SPECIFICATIONS
AMV9 Continuous Fan Speed Chart
AMV90453BXA
Cooling
Speed
Tap
A
B
C
D
AMV90704CXA
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
380*
380*
380*
403
448
493
504
560
616
505
672
739
Cooling
Speed
Tap
A
B
C
D
AMV90905DXA
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
380*
380*
380*
403
448
493
554
616
678
720
800
880
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
513*
513*
513*
554
616
678
706
784
862
907
1008
1109
AMV91155DXA
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
514*
514*
514*
554
616
678
706
784
862
907
1008
1109
1. Units are shipped without filter(s). CFM in chart is without filter(s).
2. All furnaces shipped with heating speed set at "B" and cooling speed set at "D". Installer should adjust blower speed
as needed. The first task is to determine the proper aiflow for the cooling system.
3. For most cooling applications, about 400 CFM per ton is desirable.
4. The chart is for information only. For satisfactory operation, external static pressure not to exceed value shown on
rating plate.
5. Do not operate above 0.5" w.c. ESP in heating mode. Operating between 0.5" w.c. and 0.8" w.c. is tabulated for
cooling purposes only.
6. * Motor CFM minimum.
17 Rev. 1
BLOWER PERFORMANCE SPECIFICATIONS
ACV9 Heating Speed Charts
ACV90905DXA
(Rise Range: 30 - 60°F)
ACV90704CXA
(Rise Range: 30 - 60°F)
Heating
Speed
Tap
A
B
C
D
Adjust
Tap
Low Stage
CFM
at .1" - .5" w.c.
ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
747
830
913
824
915
1007
900
1000
1100
978
1085
1194
High Stage
CFM
Rise
at .1" - .5" w.c. (°F)
ESP
1076
1195
1315
1186
1318
1449
1296
1440
1584
1408
1562
1719
Adjust
Tap
Low Stage
CFM
at .1" - .5" w.c.
ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
999
1110
1221
1067
1185
1303
1134
1260
1386
1202
1335
1469
Heating
Speed
Tap
56
50
46
51
46
42
47
42
38
43
39
35
A
B
C
D
High Stage
CFM
Rise
at .1" - .5" w.c. (°F)
ESP
1439
1598
1758
1536
1706
1876
1633
1814
1996
1730
1922
2115
56
50
46
52
47
43
49
44
40
46
42
38
AMV9/ACV9
Circulator Blower Speed Adjustment Switches
8 7 6 5
Normal
4 3 2 1
*
O
F
F
8 7 6 5 4
O
F
F
3 2 1
+ (Plus)
Adjust
O O
F N
F
8 7 6 5 4 3 2 1
- (Minus)
Adjust
O O
N F
F
Adjust Taps
(* indicates factory setting)
8 7 6 5
Cooling
Speed
Tap A
8 7 6 5
Cooling
Speed
Tap B
8 7 6 5
Cooling
Speed
Tap C
Cooling
Speed
Tap D
*
8 7 6 5
4 3 2 1
O
F
F
4 3 2
O
F
F
1
O O
F N
F
4 3 2 1
O O
N F
F
4 3 2 1
O O
N N
Heating
Speed
Tap A
Heating
Speed
Tap B
Heating
Speed
Tap C
Heating
Speed
Tap D
8 7 6 5
4 3 2 1
O
F
F
8
4 3 2 1
O
F
F
7 6 5
*
Note: There is a green LED adjacent to the
integrated control module fuse which is used
to verify airflow volume. The green CFM LED
blinks once for each 100 CFM of airflow.
Example: 10 blinks = 1,000 CFM
O O
F N
F
8 7 6 5
4 3 2 1
O O
N F
F
8 7 6 5
4 3 2 1
O O
N N
Cooling Speed Taps
Heating Speed Taps
(* indicates factory setting)
(* indicates factory setting)
Note: Continuous fan speed will be 56% of
high stage cooling speed.
Example: 1,000 CFM of cooling speed will
be reduced to 560 CFM when fan selector
switch is set to on, and no call for cooling.
1. Units are shipped without filter(s). CFM in chart is without filter(s).
2. All furnaces shipped with heating speed set at "B" and cooling speed set at "D". Installer should adjust blower speed
as needed. The first task is to determine the proper aiflow for the cooling system.
3. For most cooling applications, about 400 CFM per ton is desirable.
4. The chart is for information only. For satisfactory operation, external static pressure not to exceed value shown on
rating plate.
5. Do not operate above 0.5" w.c. ESP in heating mode. Operating between 0.5" w.c. and 0.8" w.c. is tabulated for
cooling purposes only.
6. * Motor CFM minimum.
18 Rev. 1
BLOWER PERFORMANCE SPECIFICATIONS
AMV9/ACV9
Ramping Profile
8 7 6 5 4 3 2 1
*
Ramping
Profile
Tap A
Ramping
Profile
Tap B
Ramping
Profile
Tap C
Ramping
Profile
Tap D
O
F
F
8 7 6
O
F
F
5 4 3 2 1
O O
F N
F
8 7 6 5 4 3 2 1
O O
N F
F
8 7 6 5 4 3 2 1
Note: The multi-speed circulator blower
also offers several custom ON/OFF
ramping profiles. These profiles may be
used to enhance cooling performance
and increase comfort level. The ramping
profiles are selected using DIP switches
5 and 6.
Verify profile selection by counting the
green CFM LED blinks and timing each
step of the ramping profile.
O O
N N
Ramping Profiles
(* indicates factory setting)
ACV9 Continuous Fan Speed Chart
Cooling
Speed
Tap
A
B
C
D
ACV90704CXA
ACV90905DXA
CFM at
Cooling
CFM at
Adjust
Adjust
.1" - .8" w.c. Speed
.1" - .8" w.c.
Tap
Tap
ESP
Tap
ESP
Minus(-)
380*
Minus(-)
513*
Normal
380*
Normal
513*
A
Plus (+)
380*
Plus (+)
513*
Minus(-)
403
Minus(-)
554
B
Normal
448
Normal
616
Plus (+)
493
Plus (+)
678
Minus(-)
554
Minus(-)
706
C
Normal
616
Normal
784
Plus (+)
678
Plus (+)
862
Minus(-)
720
Minus(-)
907
D
Normal
800
Normal
1008
Plus (+)
880
Plus (+)
1109
1. Units are shipped without filter(s). CFM in chart is without filter(s).
2. All furnaces shipped with heating speed set at "B" and cooling speed set at "D". Installer should adjust blower speed
as needed. The first task is to determine the proper aiflow for the cooling system.
3. For most cooling applications, about 400 CFM per ton is desirable.
4. The chart is for information only. For satisfactory operation, external static pressure not to exceed value shown on
rating plate.
5. Do not operate above 0.5" w.c. ESP in heating mode. Operating between 0.5" w.c. and 0.8" w.c. is tabulated for
cooling purposes only.
6. * Motor CFM minimum.
19 Rev. 1
BLOWER PERFORMANCE SPECIFICATIONS
ACV9 High (Single) Stage Cooling Speed Charts
ACV90704CXA
Cooling
Speed
Tap
Adjust
Tap
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
A
B
C
D
ACV90905DXA
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
720
800
880
990
1100
1210
1260
1400
1540
1620
1800
1980
CFM at Cooling
.1" - .8" Speed
Tap
w.c. ESP
540
600
660
720
800
880
990
1100
1210
1286
1429
1572
A
B
C
D
ACV9 Low Stage Cooling Speed Charts
ACV90704CXA
Cooling
Speed
Tap
A
B
C
D
Adjust
Tap
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
ACV90905DXA
CFM at Cooling
.1" - .8" Speed
w.c. ESP
Tap
378*
390
429
468
520
572
644
715
787
836
929
1022
A
B
C
D
Adjust
Tap
CFM at
.1" - .8"
w.c. ESP
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
Minus(-)
Normal
Plus (+)
513*
520
572
644
715
787
819
910
1001
1053
1170
1287
1. Units are shipped without filter(s). CFM in chart is without filter(s).
2. All furnaces shipped with heating speed set at "B" and cooling speed set at "D". Installer should adjust blower speed
as needed. The first task is to determine the proper aiflow for the cooling system.
3. For most cooling applications, about 400 CFM per ton is desirable.
4. The chart is for information only. For satisfactory operation, external static pressure not to exceed value shown on
rating plate.
5. Do not operate above 0.5" w.c. ESP in heating mode. Operating between 0.5" w.c. and 0.8" w.c. is tabulated for
cooling purposes only.
6. * Motor CFM minimum.
20 Rev. 1
WIRING DIAGRAMS
BTU OUTPUT vs TEMPERATURE RISE CHART
100
600 CFM
90
700
80
800
TEMPERATURE RISE
900
1000
70
1100
1200
60
1400
1600
50
1800
2000
2200
2400 CFM
40
30
FORMULAS
BTU OUTPUT = CFM x 1.08 x RISE
BTU OUTPUT
RISE =
÷ CFM
1.08
20
21 Rev. 1
10
30
40
50
60
70
80
90
100
OUTPUT BTU/HR x 1000
110
120
130
140
150
BLOWER PERFORMANCE SPECIFICATIONS
TO
ID BLOWER
TWO-STAGE PRESSURE
SWITCH ASSEMBLY
HIGH FIRE
PRESS. SWITCH
C
NO
HI
VT
3
C
2
PM
1
RD
WH
TWO STAGE
GAS VALVE
YL
1
2
OR
2 CIRCUIT
CONNECTOR
L
BK
-1
BR
WH-5
DISCONNECT
FLAME
SENSOR
GY
GY
NO
TO 115VAC/ 1Ø /60 HZ POWER SUPPLY WITH
OVERCURRENT PROTECTION DEVICE
C
FRONT COVER
PRESSURE SWITCH
NO
L
WARNING:
RD
BU
BU
OR
24V HUM.
PK
LOW FIRE
PRESS.
SWITCH
AUTO RESET PRIMARY
LIMIT CONTROL
VT
RD
SWITCH
JUNCTION BOX
115kBTU MODELS
INDUCTOR COIL
70kBTU,90kBTU,
ONLY
VT
BK
1
GND
BURNER COMPARTMENT
BLOWER COMPARTMENT
DISCONNECT
DOOR
INDUCED
DRAFT
BLOWER
GN
WH
2
N
GND
DISCONNECT POWER
MUST BE PROPERLY
BEFORE SERVICING.
WIRING TO UNIT
POLARIZED AND
GROUNDED.
CHASSIS GROUND
MANUAL RESET ROLLOUT
LIMIT CONTROLS
(SINGLE CONTROL ON 45 kBTU)
3
WARNING:DISCONNECT
PROPERLY POLARIZED
SERVICING. WIRING
TO UNIT MUST BE
AND GROUNDED.
POWER BEFORE
N
C
BU
115 VAC/ 1Ø /60 HZ
POWER SUPPLY WITH
PROTECTION DEVICE
OVERCURRENT
JUNCTION BOX
HOT
SURFACE
IGNITER
GND
INDOOR
AIR
CIRCULATOR
BLWR
VT
GND
YL
PK
BK
10
11
12
7
8
9
4
5
6
BU
GY
EAC-H
IND HI
WH
RD
2
HUM-N
HUM-H
HUMIDIFIER
GY
IGN-H
IGN-N
OR
HOT SURFACE
IGNITER
FP (3)
BU
3
IND-N
ID
BLWR
IND LO
BR
1
EAC-N
ELECTRONIC
AIR CLEANER
INTEGRATED CONTROL MODULE
INTEGRATED CONTROL MODULE
W2
RD
TWIN/
DEHUM
R
W1
G
B/C
Y
YLO
O
WH
FUSE
24 V
3A
VT
24 V THERMOSTAT CONNECTIONS
BR
PK
GY
24V HUM.
LINE-N
LINE-H
YL
MANUAL RESET
AUXILIARY
LIMIT CONTROL
VT
FLAME SENSOR
YL
GN
XFMR-H
XFMR-N
115 VAC
OR
VT
T-STAT SELECTOR
2
HEAT OFF DELAY
DIP SWITCHES
PK
1
2
3
4
WH
DIAGNOSTIC
LED
GY
3
24
VAC
115
VAC
5
BK
XFMR
HUM
LINE
PARK
COOL
EAC
HI
HEAT
LO
HEAT
TWO-STAGE
INTEGRATED
CONTROL
MODULE
OR
HOT
40VA
TRANSFORMER
MANUAL RESET AUXILIARY LIMIT
CONTROLS
W1
HLO (11)
MANUAL RESET ROLLOUT
LIMIT CONTROL(S)
YLO
HL1 (6)
W2
Y
TO
MICRO
C
WH
BK
BK
BK
WH
NO
MVH (1)
24V HUMIDIFIER
BK
GND
PK
HIGH FIRE
PRESSURE SWITCH
MVC (8)
0
STEADY ON = NORMAL OPERATION
1
1 FLASH = SYSTEM LOCKOUT (RETRIES/RECYCLES EXCEEDED)
GND (10)
BLOWER
COMPARTMENT
DOOR SWITCH
(OPEN WHEN
DOOR OPEN)
GND
TR (9)
2 FLASHES = LOW FIRE PRESSURE SWITCH STUCK CLOSED
3
3 FLASHES = LOW FIRE PRESSURE SWITCH STUCK OPEN
5 FLASHES = FLAME SENSED WITH GAS VALVE DE-ENERGIZED
JUNCTION
7
7 FLASHES = LOW FLAME SENSE SIGNAL
TERMINAL
8
8 FLASHES = CHECK IGNITER OR IMPROPER GROUNDING
9 FLASHES = HIGH FIRE PRESSURE SWITCH STUCK OPEN
FIELD SPLICE
HI VOLTAGE FIELD
4 FLASHES = THERMAL PROTECTIVE DEVICE OPEN
CONTINUOUS FLASHES = 115 VOLT AC POWER REVERSED
FIELD GND
HI VOLTAGE (115V)
4
C
EQUIPMENT GND
LOW VOLTAGE FIELD
6
9
SWITCH (TEMP.)
INTERNAL TO
INTEGRATED CONTROL
IGNITER
SWITCH (PRESS.)
PLUG CONNECTION
PK PINK
NOTES:
BR BROWN
1. SET HEAT ANTICIPATOR ON ROOM THERMOSTAT AT 0.7 AMPS.
OR ORANGE
WH WHITE
2. MANUFACTURER'S SPECIFIED REPLACEMENT PARTS MUST BE USED WHEN SERVICING.
VT VIOLET
BU BLUE
GN GREEN
GY GRAY
BK BLACK
RD RED
C
GAS
VALVE
INTEGRATED CONTROL MODULE
LOW VOLTAGE (24V)
2
HI
C
PS2 (2)
GN
INDUCTOR COIL
70kBTU,90kBTU,
115kBTU MODELS
ONLY
COLOR CODES:
YL YELLOW
PM
C
6
5
4
3
2
1
LOW FIRE
PRESSURE
SWITCH
NO
MVL(7)
WH
WH
5
C
NO
FRONT COVER
PRESSURE SWITCH
WH
CIRCULATOR
BLOWER
16 WIRE
ECM MTR
HARNESS
24V HUM.
PS1 (12)
G
NEUTRAL
BK
AUTORESET
PRIMARYLIMIT
CONTROL
24 VAC
FUSE 3 A
4
9 CIRCUIT CONNECTOR
RD
WH
TH (5)
R
1
24V THERMOSTAT CONNECTIONS
BK
5 CIRCUIT
CONNNECTOR
RD
40 VA
TRANSFORMER
OVERCURRENT
PROT. DEVICE
3. IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE FURNACE MUST BE
REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL HAVING A TEMPERATURE
RATING OF AT LEAST 105°C. USE COPPER CONDUCTORS ONLY.
4. UNIT MUST BE PERMANENTLY GROUNDED AND CONFORM TO N.E.C. AND LOCAL CODES.
22314701 REV.00
Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring.
AMV9_____XA (Manufacturing Numbers P1257401-06F), ACV9_____XA (Manufacturing Numbers P1257703-05F)
22 Rev. 1
SCHEMATICS
PK
TO AVOID POSSIBLE ELECTRICAL SHOCK, PERSONAL INJURY,
OR DEATH, DISCONNECT THE POWER BEFORE SERVICING.
GROUND TO
SCROLL HOUSING
WH
TO ECM
BLWR MOTOR
BK
9 CIRCUIT
CONNECTOR
TO MAIN
HARNESS
PIN 9
PIN 8
PIN 6
PIN 7
WH
WH
WH
OR
GY
BK
BK
OR
WH
BK
PIN 5
PIN 4
PIN 2
PIN 3
GY
PIN 1
PIN 4
PIN 5
VT
GN
PIN 1
PIN 2
PIN 3
INDUCTOR COIL
(GUVA070,090,115 MODELS ONLY)
PK
ECM BLOWER MOTOR
YL
AUXILIARY LIMITS
(SIDES OF BLOWER
HOUSING)
! WARNING
CIRC
LINE
NEUTRAL
EAC
CUT FOR
DEHUM
INTEGRATED CONTROL MODULE
XFMR
LOAD
WH
LINE
BK
HUM
W R
PARK
OFF
3
2
1
US
SINGLE
ON
S1
TSTAT
EAC
HOT
COOL
S4
CFM
BK
Intell-Ignition
ON
OFF
LINE
87 4321
87 4321
S3
XFMR
TRANSFORMER
HUM
TWO
HI
HEAT
C
LO
HEAT
BLOWER ASSEMBLY SCHEMATIC
AMV9/ACV9_____XA MODEL FURNACES
This schematic is for reference only. Not all wiring is as shown above,
refer to the appropriate wiring diagram for the unit being serviced.
23 Rev. 1
ELECTRONIC
AIR CLEANER
LOW
HEAT
HIGH
HEAT
COOL
CIRC.
NEU
PARK
EAC
EAC
NEU
INDUCER
IND
HI
IND
NEU
HUMN
HUM
K8a
R
K2
3 AMP
AUTOMOTIVE
FUSE
W8
K3
K1
TH
LINE HOT
XFMR
24 V.A.C.
120 VAC
XFMRN
LINE NEU
.0005
TR
R
B/C
K8b
Q22
K6
Y
G
Y
G
W2
W1
W2
W1
1M
THERMOSTAT
FP
IGNN
FLAME
SENSOR
PROBE
IGN
MV
MVL
COM
GND
C
IGNITOR
PS2
PS1
HLO
HLI
P
M
HIGH
LIMIT
H1
ROLLOUT
SWITCH
2 STAGE
GAS VALVE
AUX
LIMIT
MVH
MATE WITH AMP
1-480708-0
USING
SOCKETS
350550-1
1ST STAGE
PRESSURE
SWITCH
2ND STAGE
PRESSURE
SWITCH
TYPICAL SCHEMATIC
AMV9/ACV9_____XA MODEL FURNACES
WR 50V61-289 INTEGRATED IGNITION CONTROL
This schematic is for reference only. Not all wiring is as shown above. Refer to the appropriate wiring diagram for the unit being serviced.
TO AVOID POSSIBLE ELECTRICAL SHOCK, PERSONAL INJURY,
OR DEATH, DISCONNECT THE POWER BEFORE SERVICING.
K7
IND
LO
HUMIDIFIER
SCHEMATICS
! WARNING
24 Rev. 1
CIRCULATOR
BLOWER
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement