Quick Start E3 Install Manual

Quick Start E3 Install Manual
QUICK START INSTALLATION GUIDE
Encore
E‐3
If you are not proficient in the installation of this product or would
like a full version of the installation manual, Please visit our web
site @ www.encoreautomotivesystems.com
FOR PROFESSIONAL INSTALLATION ONLY!
Main Power Connector
3
RED / WHITE: PARKING LIGHT RELAY INPUT
4
WHITE: PARKING LIGHT OUTPUT
BLACK : MAIN SYSTEMS GROUND
+
BROWN : POSITIVE SIREN OUTPUT
RED : FUSED 12 VOLT (+) BATTERY POWER
6
8 - Pin Accessory Connector
-
GRAY WIRE / CHANNEL 3 NEGATIVE TRUNK OUTPUT
ORANGE :STARTER INTERRUPT O/P RELAY REQUIRED
YELLOW / IGNITION INPUT (+)
GREEN / (-) DOOR TRIGGER INPUT
BLUE / (-) INSTANT TRIGGER INPUT ( HOOD, TRUNK)
VIOLET / (+) DOOR TRIGGER INPUT
WHITE / DOME LIGHT (OR CH#4 O/P) RELAY REQUIRED
BROWN/ WHITE / (-) HORN OUTPUT.
TRANSMITTER PROGRAMMING:
:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter
memory is exceeded, the security system will start deleting transmitters from memory in
chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 4 TIMES and stay in ON position.
“Within 15 seconds”.
2. Push the Valet switch 4 times and hold it on the 4th push until a long chirp is heard. Then
release the valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp,
indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for
each transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light
flashes will confirm exit.
+
7.
+
8.
+
Instant Door
Ajar error
chirp
All
Confirmation
chirps On
white wire =
Dome light
output
Lock/Arm &
Unlock/Disarm
Confirmation
Chirps
ALARM with
Keyless Entry
45 seconds
delay Door Ajar
error chirp.
Siren
Confirmation
chirp on only
Car Jacking
feature Off
Car Jacking
feature On
th
white wire = 4
channel pulse
Press
Transmitt
er
Button
One Chirp /
LED one pulse
Factory Default
Setting
LED two pulses
Active arming
Passive arming
without passive
door locking
Automatic Rearm
off
Automatic Rearm
on
1
2
Two Chirps /
Three Chirps /
Four Chirps /
LED three
pulses
LED four
pulses
Passive arming
with passive
door locking.
Horn
Confirmation
chirp on only
white wire
th
=4 channel
latched
All
Confirmation
chirps off
Lock/Arm
Confirmation
Chirp Only
ADJUST AND TEST THE SENSITIVITY LEVEL OF THE SHOCK SENSOR
SECURITY FEATURE “B” PROGRAMMING:
Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
th
Push the Valet switch 4 times (holding in on the 4 push) until one long chirp is heard
then release the valet switch. You are now in the Alarm feature “B” programming
mode.
Press and release the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
1
Factory
Default
Setting
Pathway
illumination
feature “off”
2
Ignition
controlled
door locks &
unlocks
3
0.8-second
Door lock
pulses.
rd
3 Channel
(Trunk)
output
4
5
6.
+
+
Button =
Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
Push the Valet switch 5 times and hold in on the 5th push. When a long
chirp is heard, release the valet switch. You are now in the Alarm feature
‘III’ programming mode.
3
Press the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Shock Sensor Program Mode
1
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will
confirm exit
Keyless Entry
ONLY
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm
exit.
One Chirp /
LED one
pulse
1
2
Button
Two Chirps /
LED two pulses
Three Chirps /
LED three
pulses
Four Chirps
/ LED four
pulses
Parking light
turns “on” for 30second upon an
unlock signal
Parking light
turns “on” for 30second upon an
unlock signal &
10-second upon
a lock signal.
Ignition
controlled door
locks only
Ignition
controlled door
unlocks only
Without
ignition
controlled
door locks
& unlocks
3.5-second Door
lock pulse.
Double pulse
unlock
Comfort
feature
SECURITY FEATURE “A” PROGRAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 3 times (holding in on the 3rd push) until one long chirp is heard. Then
release the valet switch. You are now in the Alarm feature “A” programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
a. The siren chirps and LED pause will indicate the current setting.
b. The factory default settings is always [1] LED flash, [1] chirp.
4 Depress the transmitter button to change the feature. Simply keep re-depressing the
transmitter button until the system advances to your desired setting.
Press the transmitter button corresponding to the feature you want to program.
Shock Sensor Adjustment:
rd
3 Channel
Latch output
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 5 times holding in on the 5th push. a long chirp will be
heard. Release the valet switch. You are now in the Alarm feature ‘Shock
Sensor’ programming mode.
button for 2 seconds. One long siren chirp will indicate the
3. Press and hold
unit is ready to accept adjustments of the shock sensor.
button on the transmitter once. This will decrease sensitivity level
4. Press
by one. Each time the button is pushed and a decrease is made the
siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum
sensitivity. Warn away & full trigger will be deleted when minimum sensitivity
is selected
button on the transmitter once. This will increase sensitivity level by
5. Press
one. Each time an increase is made the siren/horn chirp will respond with [1]
chirp. Two chirps indicate the maximum sensitivity.
6. Hit the bumper or strong metal part of the vehicle to test the threshold level of
the sensor.
a). Activate the warn-away (first stage the shock sensor), the siren will
emit a short chirp.
b). Activate the full alarm (second stage the shock sensor), the siren will emit a
long chirp.
button to lock in the
7. When you are satisfied with the setting, press the
adjustment. One long siren chirp will indicate the unit has locked in the
adjustment.
Note: If 30 seconds of inactivity expires or you turn ON the ignition during of
above steps, the unit will exit the program mode and return to the disarmed
mode. Three long chirps will confirm exit.
Gray wire = Two
step door unlock
output
th
Button = 4
Channel Aux.
Silent
Arm/Disarm
Horn chirp
Duration
Horn chirp
Duration
Horn chirp
Duration
Horn chirp
duration
Standard
50 mS
30 mS
10 mS
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm
exit
FOR AUTHORIZED DEALER TECHNICAL SUPPORT,
PLEASE CALL Toll Free :(855) GO-ENCORE : 8:00 am
TO 5:00 pm PST.
TRANSMITTER PROGRAMMING:
QUICK START USERS GUIDE
If you do not understand any part of this quick start users manual
and would like the complete version, Please visit our web site @
www.encoreautomotivesystems.com . Warranty information
and product registration can also be found at our site.
The complete manual is necessary for advanced users and not all user functions
are covered in this quick start guide.
Encore E-7s Remote Transmitter
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter
memory is exceeded, the security system will start deleting transmitters from memory in
chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 4 TIMES and stay in ON position.
“Within 15 seconds”.
2. Push the Valet switch 4 times and hold it on the 4th push until a long chirp is heard then
release the valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming
chirp, indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for
each transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light
flashes will confirm exit.
ACTIVE LOCKING – LOCK & ARMING:
1. Press button on transmitter.
2. The siren or horn will chirp once and the parking lights will flash once indicating that the system is
now armed. The vehicle doors will lock upon arming when interfaced with the security system.
Note: Defective sensor reminder: If the siren or horn sounds 3 chirps, then you have left a door,
trunk, or hood lid ajar.
+
button together on
SILENT LOCKING AND UN-LOCKING: ARMING / DISARMING: Press the
the transmitter to LOCK or UNLOCK your security system, No chirp sound will be heard; arm / disarm
confirmation will be through the vehicles parking lights only.
button on the transmitter twice within 3 seconds will arm
SHOCK SENSOR BY-PASS: Pressing the
the security system and by-pass the shock sensor. The system will chirp one additional time to confirm
the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one
arming cycle only. The security system will return to normal operation during the next arming cycle
Depending on the usage, the remote batteries should be changed at least once a year .
The 1-way remote, (E-7s) is powered by a pair of 3V, CR2016 batteries. These batteries are
available at most locations batteries are sold and can be replaced by the user.
Remark Turn the ignition to the “OFF” position and exit the vehicle.
After all entrances are closed, the security system LED will flash fast for 30 seconds. If you
reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing
again once all vehicle entrances are closed.
3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren or
horn will chirp [1] time and the parking lights will flash [1] time.
PASSIVE DOOR LOCKING: Programmable
The vehicle doors will automatically lock after passive arming cycle has been completed.
Lock door / ARM
ARM (OPTIONAL)
ACTIVE UN-LOCKING: – UNLOCK & DISARM:
Arm and Delete Optional
Sensor
Car Locator
Press twice.
(OPTIONAL)
While System Armed.
Panic function
Press 3 seconds to start
and stop
TRANSMITTER OPERATION
Transmitter Button System Function Button
–
Button
Button
Button for 3
seconds
Button
–
Button
Button for 3
seconds
+
Button
+
Button for 1
seconds
*
Unlock Door / DISARM
Two Steps Door Unlock
& Disarm System
Press twice within 3
seconds. (optional
installation and
programming required)
Trunk Release
Press 3 seconds
Silent LOCK / UNLOCK
Ignition in "OFF" position.
Activate Car-Jacking
(OPTIONAL)
Ignition in "ON" position.
SILENT LOCK /
UNLOCK Programmable
+
PASSIVE LOCKING OR ARMING: Programmable
Active arming / disarming is controlling your security system via the remote transmitter. This security
system is equipped with an optional Passive Arming feature, which allows the security system to arm
30 seconds after the last door is closed. Operation is as follows.
Switching code For 2nd
Car Operation.
Press & hold until TX
LED on
1.
2.
button on the transmitter.
1. Press the
2. The siren or horn will chirp twice and parking lights will flash twice to indicate that the security
system is now disarmed. The vehicle doors will unlock when interfaced with the security system.
TAMPER DISARMING: (OPTIONAL). If the alarm is triggered; Upon disarming the system the siren or
horn will chirp 4 times and parking lights will flash 3 times. This will indicate that the alarm has been
triggered while armed.
TWO STEP DOOR UNLOCK: (OPTIONAL) This feature will independently unlock the driver’s door
button on the transmitter a second time
only when disarming the security system. Pushing the
within 3 seconds will unlock the entire vehicle. Optional installation required.
AUTOMATIC RE-LOCKING or RE-ARM: If this feature is selected, the security system will
automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will
cancel if any door is opened before the 60 seconds timer has elapsed.
DISARMING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch
The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle
normally.
VALET MODE:
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand
your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all
alarm functions are bypassed, however, the remote panic feature and remote door locks will remain
operational.
Enter Valet Mode:
1. Turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds or until the LED turns on. The LED will remain on as
long as the system is in 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'ON'.
2. Push and hold valet switch for 2 seconds; the LED will turn off indicating the system is exiting the
valet mode.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency.
1.
Press and hold the
2.
button for 3 seconds on the transmitter, the panic mode will be
To stop the alarm, press and hold the
turned off immediately.
If the button is not pressed, the alarm will automatically stop after 30 seconds.
3.
button on the transmitter for 3 seconds. The alarm will immediately sound.
TRIGGER THE SYSTEM:
When armed, your vehicle is protected as follows:
1. Light impacts will trigger the warn-away signal. A long chirp from siren /horn.
2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition switch- All will trigger the
programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren or horn and parking
lights will turn on to alert of an intrusion for 30 seconds. Then the siren or horn will stop and automatically reset
and re-arm. If any the sensors or detectors are still active, the alarm system will sound a maximum of three-30
second cycles.
ANTI CAR-JACKING: (OPTIONAL) If alarm option is installed.
Warning: If you don't need the carjacking function in this alarm system, be sure to set carjacking feature is
“OFF”. This system is default setting Car-jacking “OFF”.
1. TRANSMITTER ACTIVATED THE CAR JACKING:
+
button on the transmitter for 1 second while the vehicle’s ignition is ON. The parking
Press and hold
light will turns on for 1.5” seconds to indicate carjacking activated.
2. DOOR SWITCH ACTIVATED CAR JACKING:
1. Turn the ignition switch to “ON” position, the system is armed.
2. Once the system is armed, if you are forced from the vehicle, the system will active the car jacking trigger
when the door is opened and closed while the ignition is “ON”.
TRIGGER THE CAR JACK MODE:
3-timer circuits will function as follows:
First timer:
a. 50 seconds after the system has been triggered. The siren or horn will start chirping for 15 seconds.
b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the
car-jacking feature.
c. If not, it will enter second timer car jacking.
Second timer:
65 seconds after the system has been triggered. The siren or horn starts alarming and the parking light
starts flashing.
Third timer:
90 seconds after the system has been triggered
a. The siren or horn will still be alarming and the parking light flashing.
b. The starter disable will activate to prevent the vehicle from starting.
c. It will remain active until the vehicle's battery power exhausted.
OVERRIDE THE SYSTEM TO TURN OFF CAR JACKING:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch. The siren or horn will
stop and the system will be disarmed
IGNITION CONTROL DOOR LOCKS.
If the vehicle’s door locks have been interfaced to the security system, the system will automatically lock the
vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned
“OFF”.
TRUNK RELEASE: Press and hold
release or other electric devices.
button on transmitter for three seconds to remote control the trunk
CAR LOCATOR: Press the
button on the transmitter when the vehicle is in the armed / locked mode to active
car locator function. The siren or horn will chirp 6 times. The parking light will flash 12 times, allowing you to easily
locate your car.
SHOCK SENSOR ADJUSTMENT
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in the OFF position.
2. Push the Valet switch 5 times holding in on the 5th push until a long chirp is heard. Then release the valet
switch. You are now in the Alarm feature ‘Shock Sensor’ programming mode.
button for 2 seconds. One long siren or horn chirp to indicate the unit is ready to accept
3. Press and hold
adjustments of the shock sensor.
4. Press
button on the transmitter once. This will decrease the sensitivity level by one step. Each time the
button is pushed, a decrease is made the siren /horn chirp will respond with [1] chirp, while 2 chirp indicates
the shock sensor is OFF.
5. Press
button on the transmitter once. This will increase sensitivity level by one step. Each time an increase
is made the siren/horn chirp will respond with [1] chirp, while 2 chirp indicates maximum sensitivity.
6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor.
a). Activate the warn-away (first stage the shock sensor), the siren or horn
will emit a short chirp.
b). Activate the full alarm (second stage the shock sensor), the siren or horn will emit a long chirp.
7. When you are satisfied with the setting, press the
button to lock in the adjustment. One long siren or horn
or horn chirp will indicate the unit has locked in the adjustment.
Note: If 30 seconds of inactivity expires, or you turn on the ignition during of above steps, the unit will exit the
program mode and return to the disarmed mode. Three long chirps will confirm exit.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement