Advertisement
Advertisement
500 PSI for
Old reference
Operating instructions (ENG)
MODELS:
NWCU2250N
10070620
NWCU2250H
10070680
NWCU2350N
10070690 only
Read these instructions before using the machine.
86322410-M
09/30/11
2
Machine Data Log / Overview
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
OVERVIEW
Phone Number:
Sales Representative: for
Old version cleaning solution to the carpet and then vacuums the soiled water back into the recovery tank.
only
Thank you for purchasing a C400 product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.
To register you product go to : www.century400.com/support/warranty/register.php
For customer assistance:
1-800-776-2436
86322410 NINJA WARRIOR 500 PSI
Table of Contents
Machine Data Log / Overview. . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . 4
Safety
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . 5
HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . . 6
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . 8
PARTS
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Control Panel with Heat . . . . . . . . . . . . . . . . . . . . 22
Electrical with 2 Stage Vacuum . . . . . . . . . . . . . . 24
Electrical with Heat / 3 Stage Vacuum . . . . . . . . . 26
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Pump with Heat. . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Vacuum, 2-Stage / 3-Stage. . . . . . . . . . . . . . . . . . 42
Operations
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . 9
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . . 11 for
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wiring - 2 Stage Vacuum . . . . . . . . . . . . . . . . . . . 44
Wiring - 3 Stage Vacuum . . . . . . . . . . . . . . . . . . . 46
Wiring with Heat . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Suggested Spare Parts . . . . . . . . . . . . . . . . . . . . . 50
Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 version
Maintenance
Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . . 14
Daily/Regular Maintenance. . . . . . . . . . . . . . . . . . . 14
Vacuum Motor Replacement . . . . . . . . . . . . . . . . . 15
Solution Pump Replacement . . . . . . . . . . . . . . . . . 16
Pressure Regulator . . . . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 only
86322410 NINJA WARRIOR 500 PSI 3
4
How to Use This Manual
This manual contains the following sections:
• How to Use This Manual
• Safety
The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death.
• Operations
• Maintenance
• Parts List
The OPERATIONS section is to familiarize the operator with the operation and function of the machine.
The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order:
Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the
MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual.
Model:
Date of Purchase: for
Old
Serial Number: version
• REF – column refers to the reference number
Dealer:
Address:
• Maintenance
• Lubrication
• Vacuum Motor Replacement
• Solution Pump Replacement
• Troubleshooting on the parts illustration.
Phone Number:
• PART NO. – column lists the part number for
Sales Representative: the part.
The model and serial number of your machine is located approximately where shown.
• PRV NO. – reference number.
• QTY – column lists the quantity of the part used in that area of the machine.
Serial Number
Tag
• DESCRIPTION – column is a brief description of the part.
• SERIAL NO. FROM – If this column has an (*) only column has two asterisk (**), call manufacturer for serial number. The serial number indicates the first machine the part number is applicable to. The main illustration shows the most current design of the machine. When a boxed illustration is shown, it displays the older design.
• NOTES – column for information not noted by the other columns.
NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts.
NOTE: The manual part number is located on the lower left corner of the front cover.
86322410 NINJA WARRIOR 500 PSI
Safety
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet . See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service.
Use only
Do not ments.
indoors. Do not use outdoors or expose to rain.
for
Old
allow machine to be used as a toy. Close attention is necessary when used by or near children.
version
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly , has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
This machine is intended for cleaning carpet only.
only
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
86322410 NINJA WARRIOR 500 PSI 5
Safety
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY.
The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
for
Unless Operation Guide is Read and understood.
version
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine.
Use only manufacturer approved replacement parts.
only
6 86322410 NINJA WARRIOR 500 PSI
Safety
Safety Labels
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them.
Label Warning
86244300
PRV # 500955 for
Old reference only
WARNING!
FOR YOUR PROTECTION USE A
GROUND FAULT CIRCUIT INTERRUPTER
Label Circuit Interrupter
86200570
PRV # 170-41
86322410 NINJA WARRIOR 500 PSI 7
8
Safety
Grounding Instructions
THIS PRODUCT IS FOR COMMERCIAL
USE ONLY.
ELECTRICAL:
In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
EXTENSION CORDS: machine, and must be limited to 50 feet (15.5m) in length.
GROUNDING INSTRUCTIONS:
Old least one size larger than the power cord on the for version
This appliance must be grounded. If it should malfunc-
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified tion or break down, grounding provides a path of least electrician.
resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in "Fig.
A". A temporary adaptor that looks like the adaptor in
"Fig. C" may be used to connect this plug to a 2-pole receptacle as shown in "Fig. B", if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or wire extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover.
Whenever the adaptor is used, it must be held in place by a metal screw.
only
86322410 NINJA WARRIOR 500 PSI
Technical Specifications
MODEL
ALL
10070620
10070680
10070690
ITEM
Electrical
Solution Pump
Solution Capacity
Recovery Capacity
Height
Length
Width
115 Volt, 60 hz, 15A
500 psi
13 Gal
11 Gal
43 inches
30 inches
22 inches
Vacuum Motor
Weight- Empty
Weight-Full Solution
Power cord for
Old
Weight-Full Solution
Power cord
Dual 2 Stage
127 lbs
232 lbs
1 X 25 feet
Dual 2 Stage
134 lbs version
1850 watts Heater
Vacuum Motor Dual 3 Stage
Weight- Empty
Weight-Full Solution
Power cord
129 lbs
234 lbs
2 X 25 feet
MEASURE
Operations
Width only
Length
Height
86322410 NINJA WARRIOR 500 PSI 9
Operations
Controls
1
2
3 4 5 for
Old
11
10
1.
Vacuum Accessory Tool Hook-up
2.
Solution Pump Switch
3.
Vacuum 1 Switch
4.
Vacuum 2 Switch
5.
Heater Switch with On Light (Units w/Heat Only)
6.
Pressure Gauge
9 8 7
7.
Adjustable Pressure Relief Valve
8.
Heater Temperature Light (Units w/Heat Only)
9.
only
11. Solution Accessory Tool Hook-up
6
10 86322410 NINJA WARRIOR 500 PSI
Operations
Machine Operation
Care must be exercised in the use of all chemicals.
Chemicals are poisonous and can pose a health risk.
Read and follow manufacturers instructions regarding dangers and correct usages.
Only use chemicals approved for use with this machine. Use of non-compatible chemicals may cause machine damage and will not be covered under the warranty. Carefully read ingredients on manufacturer’s label before using any product in this machine.
Do not let pump run dry.
The internal parts of the pump used in the machine are suitable for use with most carpet cleaning chemicals.
But they are susceptible to chemical attack from some cleaning substances, such as hydrocarbon solvents and chlorinated bleaches. These non-compatible materials are not of the type used for carpet cleaning.
Chemicals
• Alkalis
• Detergents for
Suitable Chemicals
Old reference
• Hydroxides
• Soaps
Do not let pump run unattended.
• Vinegar
Non-Compatible
• Aldehydes
• Aromatics Hydrocarbons
• SP Butyls
• Carbon Tetrachloride
• Clorox*
• Chlorinated Bleaches
• Chlorinated Hydrocarbons
• Lysol*
• Methyl Ethel Ketone (MEK)
• Perchorethylene (perc)
• Phenolics
• Trichlorethylene
• D-Limonene only
*Registered Trademark
86322410 NINJA WARRIOR 500 PSI 11
Operations
Pre-Run Inspection
1.
Check all fittings and connectors for proper assembly.
Heater Operation
NOTE: Units with Heat Only
2.
Check all hoses for leaks. Repair or replace any damaged hoses.
3.
Check power cord(s) for any damage. If damaged, replace.
The solution fittings on the machine will become extremely hot during operation. Allow sufficient time to cool, or run solution through the machine with the heater turned off before disconnecting or performing any maintenance on the heater.
Equipment Set-up
Plug the two power cords into separate grounded circuits. The heater draws 15 amps of current.
1.
Plug power cord from machine into properly grounded wall outlet.
2.
Turn vacuum motor switch on and off to make sure
3.
there is electrical power at machine.
Using a clean container, fill the solution tank with clean hot water. Do not use water over 130°F. Mix in a non-foaming cleaning concentrate for use in facture's instructions printed on container.
4.
Connect priming hose to solution fitting on
Turn the solution pump ON. Fully prime the solution system before turning heater on.
Turn the heater switch on. The red light on the heater version machine. Turn on pump and run for 30 seconds or switch will be on when the heater switch is on. The red heater temperature light will be on when the heater is active and will turn off when the heater reaches maximum temperature.
On initial start-up the heater will take a few minutes to reach operating temperature.
until a steady flow of water is coming out of priming hose. Turn off pump and disconnect priming hose.
When turning the pump and heater OFF, make certain that you turn the heater off FIRST.
5.
Connect vacuum hose to machine. Slide the swivel cuff over the outlet on the tank.
6.
Connect the hose to your machine and wand. Pull back the knurled collar on the quick disconnect coupler and push onto the connection on the chassis. To avoid leaks, check to be that a positive connection was made.
NOTE: When using a powder cleaner, pre-mix with hot water in a clean container before adding to the solution tank.
only
7.
Turn pump and vacuum switch(es) to the on position.
12 86322410 NINJA WARRIOR 500 PSI
Cleaning
Always use defoamer if foaming occurs. Foam will suspend large particles that may damage vacuum(s) as well as allow liquid into the vacuum motor(s) without activating the float shutoff.
1.
Prior to cleaning, make certain that the nozzle is functioning properly.
a.
To check, hold the wand about one foot above the surface to be cleaned and open the wand
2.
b.
valve. A full spray should be observed from the nozzle.
If the nozzle is not showing a full spray pattern, adjust nozzle for proper pattern, clean, or replace nozzle.
for version may be used in a scrubbing manner, applying chemical in both the push and pull stroke.
3.
When cleaning, keep the working opening (wand mouth) flat on the surface being cleaned. Keep the wand moving when the valve is open.
4.
The shutoff float inside the vacuum tank will impede the vacuum flow when the vacuum tank is full. When this occurs, empty the vacuum tank by opening the dump valve and dispose of the waste in a proper manner.
5.
Once the vacuum tank has been emptied, you may once again proceed with cleaning only
Operations
86322410 NINJA WARRIOR 500 PSI 13
Maintenance
Periodic Maintenance Daily/Regular Maintenance
Twice a month, flush a white vinegar solution (one quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the machine. This will prevent build-up of alkaline residue in the system.
Before making any repairs or adjustments to the machine, disconnect the power cords from the
electrical source.
Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. The electrical cable must be well insulated and cable connector screw kept tight. If
1.
Empty unused cleaning solution from the solution tank.
2.
Inspect and clean filter screen in solution tank.
the cable insulation is broken or frayed, repair or
3.
Flush pumping system with 1 to 2 gallons of clean replace immediately. Don't take chances with electrical fire or shock.
water.
for
Old
4.
After each use, rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if necessary, using a Hospital Grade Virucide or a
10-1 bleach to water solution. Waste water should
SERVICE SCHEDULE be disposed of properly.
version
DAILY WEEKLY QUARTERLY
Check machine for cord damage
Check recovery dome and gasket for damage and cleanliness
Check hoses for wear, blockages, or damage
Check handles, switches, and knobs for damage
Run one gallon of water through solution system
Clean out recovery tank and check float valve to make sure it moves freely
*
*
*
*
*
*
Clean out solution tank and remove and clean vacuum intake screen
Clean outside of all tanks and check for damage
Run vac motor for at least one minute to allow motor to dry
Store with dome off tank to allow the tank to dry
Check all gaskets for wear and leakage
Check pump pressure; observe spray pattern and check with gauge if only *
*
* necessary
*
Check and clean solution screen
Check cables for fraying
Check overall performance of machine
Check vac motor carbon brushes
*
*
*
*
*
*
14 86322410 NINJA WARRIOR 500 PSI
Maintenance
Only qualified maintenance personnel are to perform the following repairs.
Vacuum Motor Carbon Brushes Replacement
End Cap
Vacuum Motor Replacement
1.
Turn off all switches and unplug machine.
Carbon
Brushes
2.
Remove hardware under front of machine to access component compartment.
WARNING: The green ground wire 3.
Remove vacuum motor cover and disconnect must be attached for motor wires.
4.
Remove the vacuum motor.
5.
Reverse process to install vacuum motor.
for safe operation. See wiring diagram.
If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced version
Important:
These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.
only
3
8
[9.5mm]
Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less than
3/8" (9.5mm) long.
86322410 NINJA WARRIOR 500 PSI 15
Maintenance
Solution Pump Replacement
Only qualified maintenance personnel are to perform the following repairs.
500 psi for
Old
86201040 reference
PRV NO. 250-73C only
Valve & O-Rings Kit
(both sides)
86201030
PRV NO. 250-73B
Plunger & Seals Kit
86201080
PRV NO. 250-75A
16 86322410 NINJA WARRIOR 500 PSI
Only qualified maintenance personnel are to perform the following repairs.
Pressure Regulator
For best results with the pressure regulator, we recommend that you clean and lubricate the piston and u-cup with Superlube lubricant monthly or when pressure drop seems excessive.
1.
Turn unit off before lubricating.
2.
Remove cap, spring and spring retainer plate.
3.
With fingertips remove piston and u-cup.
4.
Wipe piston and u-cup clean of any film or scale.
5.
Lubricate the piston and u-cup with Superlube.
6.
Reassemble regulator.
7.
version normal operation.
for
Old
Lubricate U-Cup with Superlube Monthly.
only
REBUILD KIT
8.619-924.0
(GREEN 500 PSI)
Maintenance
86322410 NINJA WARRIOR 500 PSI 17
18
Maintenance
Troubleshooting
PROBLEM
Loss of Power
Electrical shock
Vac motor speed varies or doesn't run
Loss of vacuum
Pump runs no solution
Pump runs, loss of pressure
Pump will not run
Solution hose fitting hard to connect
Carpet not getting clean
Carpet too wet
Carpet browning
Solution not flowing properly
CAUSE
Unit not plugged in
Dead electrical circuit
Faulty power cord
Receptacle not grounded
Internal wiring problem
SOLUTION
Connect unit to 3 prong grounded outlet.
Check building circuit breaker or fuse box.
Replace
Contact an electrician to check building's wiring
Have a trained service technician check machine's wiring
Reset Breaker
Replace
Replace
Vacuum circuit breaker tripped
Faulty vacuum motor
Faulty switch
Loose vacuum dome
Crack in dome of poor joint
Lint or dirt clogging vacuum screen for
Center and seal dome over tank
Replace or repair using acrylic plastic cement only
With power off clean screen
Loose cuffs on vacuum hose
Vac motor seals leaking
Floor tool vac chamber clogged
Vacuum hose damaged
Tighten cuffs turning counterclockwise
Replace
Recovery tank full / Float ball stuck in the up position
Pump inlet screen plugged
Pump not primed
Turn off power, drain recovery tank.
Clean inlet screen
Prime pump with priming hose
Internal or external solution line damaged and leaking
Replace
Internal pump components wearing out Replace, see pump kit components
Check valves in pump head for particles or cuts in seals
Faulty switch
Loose wiring
Corrosion on fittings.
Take piston from BPR and lubricate with Superlube. If problem still exists change BPR kit only vinegar). Lubricate lightly with silicone base lubricant.
Severe soil conditions
Over saturation
Leaving carpet too wet
Too much chemical
Solution hose connection
Faulty pump
Faulty floor tool valve / Nozzle
Faulty pump switch
Make several passes at right angles to each other. Use a pre-spray.
Adjust solution pressure to lower settings. Make several passes without spray
Check for loss of vac pressure
Check label for correct solution concentration
Check for positive connection
Repair or replace
Repair or replace
Repair
86322410 NINJA WARRIOR 500 PSI
for
Old reference only
86322410 NINJA WARRIOR 500 PSI
Control Panel
4
7
8
9
12 for
Old
2
5
14 reference
6
3
13
1
10 only
12
11
15
20 86322410 NINJA WARRIOR 500 PSI
Control Panel
REF PART NO.
PRV NO.
QTY DESCRIPTION
7
8
5
6
3
4
1
2
86180350 12-800035 1 ELL, 1/4FP X 1/4T BR
86202230 390-09A 2 WASHER 9/16 S/S USS THICK
86002370
86002450
20035
22015
1
1
CLAMP, 7/16 DIA NYLON UL
COUPLER, 1/4 QD
86197390
86005700
86276820
86007140
31021
57104
70740
72130
1
2
6
3
ELBOW, 1/4NPT 45D STREET
NUT, 10-32 HEX W/STAR
SCR, 10-32 X 1/2 PTHMS BLK NP
SWITCH, SPST 2-POSITION ROCKER
9 86008900
10 86005720
11 86323500
12 86313020
13 86313030
14 86318320
15 86323310
80845
57106 for
-
-
-
-
2 BOOT, SEAL PUSH BUTTON 7/16” Old
NUT8-32 W/STAR WASHER PLTD
PANEL, CONTROL, 500
GASKET, .125 T X .25 W X 15.6”
-
4 GASKET, .125 T X .25 W X 7.2”
2
1 version
SERIAL NO.
FROM
NOTES only
86322410 NINJA WARRIOR 500 PSI 21
Control Panel with Heat
4
7
8
16
15
9
11 for
Old
5
2
13
17
3
6
14
10
11
12
1
18 only
22 86322410 NINJA WARRIOR 500 PSI
Control Panel with Heat
REF PART NO.
PRV NO.
QTY DESCRIPTION
7
8
5
6
3
4
1
2
86180350 12-800035 1 ELL, 1/4FP X 1/4T BR
86202230 390-09A 2 WASHER 9/16 S/S USS THICK
86002370
86002450
20035
22015
1
1
CLAMP, 7/16 DIA NYLON ULS
COUPLER, 1/4 QD
86197390
86005700
86276820
86007140
31021
57104
70740
72130
1
2
6
3
ELBOW, 1/4NPT 45D STREET
NUT, 10-32 HEX W/STAR
SCR, 10-32 X 1/2 PTHMS BLK NP
SWITCH, SPST 2-POSITION ROCKER
9 86008900
10 86311840
11 86313020
12 86313030
13 86318320
14 86323310
15 86318780
16 86317850
17 86233480
80845 for
-
-
-
-
-
2 BOOT, SEAL PUSH BUTTON 7/16” Old
PANEL, CONTROL, 500 HEAT
GASKET, .125 T X .25 W X 15.6”
GASKET, .125 T X .25 W X 7.2”
-
-
2 BREAKER, 13A, 250VAC, 32VDC
1
1
1 version
1 CLIP, NEON LAMP -
18 86005720 57106 2 NUT8-32 W/STAR WASHER PLTD
SERIAL NO.
FROM
NOTES only
86322410 NINJA WARRIOR 500 PSI 23
Electrical with 2 Stage Vacuum
13
1 19
18
10
9
7
14
3 for
Old
3
17
5 version
11
2
4
15
8
12 only
24 86322410 NINJA WARRIOR 500 PSI
Electrical with 2 Stage Vacuum
REF PART NO.
PRV NO.
QTY DESCRIPTION
1 86201510
2 86005670
3 86005700
4 86273830
5 86006850
6 86256200
7 86255900
8 86010630
9 86316460
10 86316540
11 86316700
12 86318620
13 86319090
14 86319110
15 86317580
16 86005810
17 86323330
18 86198460
19 86006590
390-26
57040
57104
70020
70393
73200
73538
87013
2 SPACER NYLON 1/4ID X 1/2 OD
1 NUT, 1/2 NPT CONDUIT
3 NUT, 10-32 W/STAR WASHER PLTD
2 SCR, 1/4-20 X 1/2 HHCS SS
2 SET SCR, 1/4-20 X 1.25L
1 STRAIN RELEIF, 1/2 NPT FLEX
2 STANDOFF, 6-32 X 5/8 HEX NYL
2 WASHER, 1/4 X 5/8 FLAT SS
-
-
-
for
1 BRKT, ELECTRICAL Old
CONNECTOR, 5 POS, PUSH WIRE
BRKT, CORD STRAIN RELIEF
CORD ASM, 14/3 SJT X 25' BLK
-
57245
1 FUSE HOLDER, PANEL MNT
1
1
2 version
2 WASHER, 1/4" ID X 1.0D FLAT BLK -
20008
70088
1 CLAMP, 5/8 NYLON UL/CSA
1 SCREW, 10-32 X 1/2 PPHMS SS NP
SERIAL NO.
FROM
NOTES only
86322410 NINJA WARRIOR 500 PSI 25
Electrical with Heat / 3 Stage Vacuum
13
1
19
10 18
9
7
14
15
3
3
4
2 for
Old
11
17
5
16 reference
8
12 only
26 86322410 NINJA WARRIOR 500 PSI
Electrical with Heat / 3 Stage Vacuum
NOTES REF PART NO. PRV NO. QTY DESCRIPTION
1 86201510 390-26 2 SPACER NYLON 1/4ID X 1/2 OD
2 86005670 57040 2 NUT, 1/2 NPT CONDUIT
3 86005700 57104
4 86273830 70020
3
2
NUT, 10-32 W/STAR WASHER PLTD
SCR, 1/4-20 X 1/2 HHCS SS
5 86006850 70393
6 86256200 73200
7 86255900 73538
8 86010630 87013
2
2
2
2
SET SCR, 1/4-20 X 1.25L
STRAIN RELEIF, 1/2 NPT FLEX
STANDOFF, 6-32 X 5/8 HEX NYL
WASHER, 1/4 X 5/8 FLAT SS
9 86316460
10 86316540
11 86316700
12 86318620
13 86319090
14 86319100
-
-
for
1 BRKT, ELECTRICAL Old
2 CORD ASM, 14/3 SJT X 25' BLK
2 version
1 FUSE, 1/4" X 1 1/4", 15A -
1 FUSE, 1/4" X 1 1/4", 4A 15 86319110
16 86005810 57245 2 NUT, 1/4-20 NYLOCK
17 86323330 -
18 86198460 20008
19 86006590 70088
2 WASHER, 1/4" ID X 1.0D FLAT BLK
1 CLAMP, 5/8 NYLON UL/CSA
1 SCREW, 10-32 X 1/2 PPHMS SS NP
SERIAL NO.
FROM
1 REQ. FOR 3-STAGE
VACUUM MACHINES
1 REQ. FOR 3-STAGE
VACUUM MACHINES
MACHINES WITH
HEAT ONLY only
86322410 NINJA WARRIOR 500 PSI 27
Frame
1
11
2
9 for
Old
6
5
3
4 only
7
8
28 86322410 NINJA WARRIOR 500 PSI
Frame
REF PART NO.
PRV NO.
QTY DESCRIPTION
7
8
5
6
3
4
1
2
86199430 040-03
86001660 41236
86005810
86276080
57245
70595
86010630
86005700
86010730
86300070
87013
57104
87088
-
2 CASTER, SWIVEL 4" 250# CPCTY
2 HUBCAP, 5/8 SHAFT
8 NUT, 1/4-20 HEX NYLOCK SS
1 SCR, 10-32 X 1” PPHMS GRN
8 WASHER, 1/4 X 5/8 FLAT SS
2 NUT, 10-32 HEX W/STAR
4 WASHER, 5/8 X 1-3/16 FLAT SS
2 HUBCAP, 9.75" WHEEL
9 86309790
10 86312830
11 86277500
-
-
70853 for
2 WHEEL, 12" X 2.25” Old
FRAME, 5/8" AXLE, DUAL VAC
SCR,1/4-20 X 5/8 CARR SS reference
SERIAL NO.
FROM
NOTES only
86322410 NINJA WARRIOR 500 PSI 29
Heater
13
7
10
14
13
14
18
19 for
Old
11
3
6 version
12
8
9
13 15
17
20
13
16
2
1
TO CONSOLE SOLUTION
FROM PUMP
2
7 only
30
6
4
86322410 NINJA WARRIOR 500 PSI
Heater
REF PART NO.
PRV NO.
QTY DESCRIPTION
7
8
5
6
3
4
1
2
86200260 151-50C
86197360 31016
86005810
86273830
57245
70020
86233410
86010630
86318310
86318410
81270
87013
-
-
1 HOSE,PULSE 47.0 1/4MPTX1/4MPT
2 ELBOW, 1/4 NPT STREET
1 NUT, 1/4-20 HEX NYLOCK SS
2 SCR, 1/4-20 X 1/2 HHCS SS
2 CLAMP, 3/4 DIA CUSHION .406 DIA
3 WASHER, 1/4 X 5/8 FLAT SS
2 CLAMP, 3.25 WORM GEAR SS
1 BRKT, HEATER MOUNT
9 86318750
10 86006180
11 86199980
14 86010650 for
-
66095
130-14
12 86201790 130-14C
13 86200870 300-06A
1 HEATER ASM, 1850W, 120V Old
PLUG, 1/8 MPT HEX BRASS
CARTRIDGE HEATER, 5/8" X 10"
THERMOSTAT RESET 302
15 86266020 76029L
16 86266130 76044L
7 SCR, 6 X 3/16, PHSMS, B
3
1
1 version
1 THERMOSTAT W/VERT SPADE 17 86317510 -
18 86317730
19 86326680
-
-
20 86202220 390-01
1 INSULATION, HEATER
1 HEATER CART. CASE WELDED
4 WASHER #5 SS .135ID X .312 OD
SERIAL NO.
FROM
NOTES only
86322410 NINJA WARRIOR 500 PSI 31
Labels
3A
3B
2 for
Old reference only
1
32 86322410 NINJA WARRIOR 500 PSI
Labels
REF PART NO.
PRV NO.
QTY
1 86318260
2 86318270
3A 86318280
3B 86318290
-
-
-
-
DESCRIPTION
1 LABEL, NINJA, WARRIOR, LH
1 LABEL, NINJA, WARRIOR, RH
1 LABEL, NINJA, WARRIOR, W/ HEAT
1 LABEL, NINJA, WARRIOR, W/O HEAT
SERIAL NO.
FROM
NOTES for
Old reference only
86322410 NINJA WARRIOR 500 PSI 33
Pump
23
21
16
TO PRESSURE GAUGE
19
7
2
4 for
Old
7
24
22
17
5
6
20
1
TO SOLUTION TANK
9
6
18
FROM SOLUTION TANK
7
13
11
3
15 only
15
14
15
25
34
15
12
86322410 NINJA WARRIOR 500 PSI
Pump
NOTES REF PART NO.
PRV NO.
QTY DESCRIPTION
7
8
5
6
3
4
1
2
86190520 11-800224 2 PLUG, 3/8 SOCHD BR
86200260 151-50C 2 HOSE,PULSE 47.0 1/4MPT X 1/4MPT
86323300
86197270
-
04008
12
1
WASHER, 1/4” RUBBER
ADPTR, 1/4MPT X 1/4FPT BR
86197290
86233150
86197360
86197420
14076
20042
31016
31026
1
2
2
1
BUSHING, 3/8 MPT X 1/4 FPT HEX
CLAMP, 3/8 WORM GEAR
ELBOW, 1/4 NPT STREET
ELBOW, 3/8NPT STREET
9 86282320
10 86240500
11 86005810
12 86273810
13 86197760
14 86233410
15 86010630
16 86317550
17 86318980
39710
40095
57245
70018 for
1 HOSE, 1/2ID WIRE BOUND X 26” Old
HOSEBARB, 3/8MPT X 3/8HOSE 90
NUT, 1/4-20 HEX NYLOCK SS
SCR, 1/4-20 X 1.00 HHCS SS
87013
-
1 TEE, 1/4 STREET
1
10
1 version
1 MOTOR, M53, 120V, 3A W/ CAM
18 86318990
19 86321290
20 86321470
21 86317590
22 86270850
23 86321660
24 86355740
25 86005710
-
-
-
-
57026
-
-
57105
1 PUMP, SERIES 207V
1 BPR, 500PSI
1 HOSE, 3/8ID WIRE BOUND X 26"
1 HOSE, 10” 1/4JIC X 1/8MPT SS
3 NUT, 8-32 HEX NYLOCK
1 ELBOW, 1/4 MPT X 1/8 FPT
1 BRKT, P/P BPR
1 only
SERIAL NO.
FROM
INCLUDES
RECTIFIER
86322410 NINJA WARRIOR 500 PSI 35
Pump with Heat
25
21
TO PRESSURE GAUGE
16
19
6
22
20
24
7
TO SOLUTION TANK
1
2
7 for
Old
23
17 version
8
5
13
7
10
18
FROM SOLUTION TANK
9
6
11
15 only
3
36
15
12
86322410 NINJA WARRIOR 500 PSI
Pump with Heat
NOTES REF PART NO.
PRV NO.
QTY DESCRIPTION
7
8
5
6
3
4
1
2
86190520 11-800224 2 PLUG, 3/8 SOCHD BR
86317840 1 HOSE,PULSE 16” 1/4MPT X 1/4MPT
86323300
86197270
-
04008
12
1
WASHER, 1/4” RUBBER
ADPTR, 1/4MPT X 1/4FPT BR
86197290
86233150
86197360
86197420
14076
20042
31016
31026
1
2
2
1
BUSHING, 3/8 MPT X 1/4 FPT HEX
CLAMP, 3/8 WORM GEAR
ELBOW, 1/4 NPT STREET
ELBOW, 3/8NPT STREET
9
10 86240500
11 86005810
12 86273810
13 86197760
14
86282320
-
15 86010630
16 86317550
17 86318980
39710
40095
57245
70018 for
-
1 HOSE, 1/2ID WIRE BOUND X 26” Old
HOSEBARB, 3/8MPT X 3/8HOSE 90
NUT, 1/4-20 HEX NYLOCK SS
SCR, 1/4-20 X 1.00 HHCS SS
87013
-
1 TEE, 1/4 STREET
-
8
1 version
1 MOTOR, M53, 120V, 3A W/ CAM
18 86318990
19 86321290
20 86321470
21 86317590
22 86270850
23 86200260
24 86355740
25 86321660
-
-
-
-
57026
-
-
-
1 PUMP, SERIES 207V
1 BPR, 500PSI
1 HOSE, 3/8ID WIRE BOUND X 26"
1 HOSE, 10” 1/4JIC X 1/8MPT SS
3 NUT, 8-32 HEX NYLOCK
1 HOSE, PULSE 47.0 1/4MPTX1/4MPT
1 BRKT, P/P BPR
1 only
SERIAL NO.
FROM
INCLUDES
RECTIFIER
86322410 NINJA WARRIOR 500 PSI 37
Recovery
18
15
3
8 14
21
2
4
19 for
Old
10 reference
10 12
13
10
5
20
16
17
9
7 only
1
6
11
38 86322410 NINJA WARRIOR 500 PSI
Recovery
REF PART NO.
PRV NO.
QTY DESCRIPTION
7
8
5
6
3
4
1
2
86161460 15-808123 1 DUMP VALVE, 1 1/2
86002620 260-64A 1 ACCESS, COVER CLEAR 6" W/RIM
86197820
86004000
31002
35255
1
1
ELBOW, 1.5 FPT X FS PVC
GASKET, TANK LID
86197040
86273740
86273750
86275800
57264
70010
70011
70546
2
2
4
6
NUT, 5/16-18 HEX ACORN PLTD
SCR, 1/4-20 X 1.50 HHCS SS
SCR, 1/4-20 X 5/8 HHCS SS
SCR, 8 X 3/4 PFHT/S BLK ZINC
9 86010630
10 86010670
11 86323330
12 86011020
13 86001350 140390
14 86311510
87013
87029
89202 for
-
-
4 WASHER, 1/4 X 5/8 FLAT SS Old
WASHER, 5/16 X 3/4 SS
WASHER, 1/4 ID X 1.0 OD FLAT BLK
WHEEL, 3" DIA. CUSHION RUBBER
15 86312360
16 86313040
-
-
2 BUSHING, SPANNER .435 X 1.10
1
1
1 version
2 BRKT, CORD, MOUNT 17 86316710 -
18 86317230
19 86317720
20 86320790
21 86233120
-
-
-
20019
1 HOSEBARB,1.5MPT X 1.5 W/FLNG
2 SCR, 5/16-18 X 2.50 BSHCS SS
1 PIPE ASM, 2", VACUUM
1 CLAMP, 2.75" WORM GEAR
SERIAL NO.
FROM
NOTES only
86322410 NINJA WARRIOR 500 PSI 39
40
Solution
17
10
18
15
20
9
3
19 for
Old
1
22
1
5
2
11
1
22
1
4
24
14
7
7
6
14 only 12
21
16
13
23
8
86322410 NINJA WARRIOR 500 PSI
Solution
REF PART NO.
PRV NO.
QTY DESCRIPTION
1 86173640 11-800437 2 ADPT,3/8 BLKHD
2 86233150 20042 2 CLAMP, 3/8 WORM GEAR
3 86238460
4 86197940
36259
40027
2
1
HOOK, STRAP
HOSEBARB, 3/8 MPT X 1/2 HOSE 90°
5 86001550
6 86273740
7 86273830
8 86005810
40043
70010
70020
57245
1
1
11
2
HOSEBARB, 3/8 MPT X 3/8 HOSE 90°
SCR, 1/4-20 X 1.50 HHCS SS
SCR, 1/4-20 X 1/2 HHCS SS
NUT, 1/4-20 HEX NYLOCK SS
9 86324210
10 86276160
11 86007970
12 86233410
13 86010670
14 86010630
15 86323330
16 86311990
-
70604
73864
81270 for
-
-
-
4 SCR, 1/4-20 X 5/8 BHCS BLK Old
SCR, 10-32 X 5/8 PPHMS BLK
STRAINER, 3/8 IN. NPT 60 MESH
CLAMP, 3/4 DIA CUSHION .406 DIA
2 WASHER, 5/16 X 3/4 SS
12
2
1 version
1 LID, SOLUTION, COVER 17 86312000
18 86312010
19 86312350
20 86297620
21 86317560
22 86318790
23 86242130
24 86324030
-
-
-
-
-
48100
-
1 LID, SOLUTION, HINGE BRKT
1 TANK, SOL, TRIM
2 STRAP, HAND TOOL
1 SPACER, .50 ODX .28 ID X 1.0L
2 WASHER, 1.032ID X 1.5OD X .062THK
2 KNOB, 1/4 HEX PRESS-LOC WING
2 PLATE, MOUNTING, SOLUTION only
SERIAL NO.
FROM
NOTES
COMPLETE
86322410 NINJA WARRIOR 500 PSI 41
42
Vacuum, 2-Stage / 3-Stage
13A
13B for
Old
2
1
4
12
5
9
6
7 only
10
3
4
8A
8B
86322410 NINJA WARRIOR 500 PSI
Vacuum, 2-Stage / 3-Stage
REF PART NO.
PRV NO.
QTY DESCRIPTION
1 86005810
2 86274090
3 86233430
4 86010630
5 86278990
6 86311520
7 86312990
8A 86314710
57245
70092
81431
87013
87017
-
-
-
8 NUT, 1/4-20 HEX NYLOCK SS
5 SCR, 10-32 X 1.5 PPHMS
2 CLAMP, 2.50 WORM GEAR
16 WASHER, 1/4 X 5/8 FLAT SS
8 WASHER, #8 X 3/8 FLAT
1 MANIFOLD, VACUUM, DUAL
1 GASKET, VAC MANIFOLD, DUAL
8 SCR, 1/4-20 X 5.50 HHCS PLT
8B 86277840 00-000167 8 SCR, 1/4-20 X 6.5 HHCS PLT
9 86317630
10 86318300
11A 86318760
11B 86318770
86135320
-
-
for
Old
SCR, #8 X 3/4" PPHSMS TYPE AB
HOSE, VAC, 2.0 ID X 18.5"L
VAC ASM, 2-STAGE, 120V
12 86312080
13A 86312220
-
-
2 VAC ASM, 3-STAGE, 120V
-
2
2 version
2 BASE, VAC MOTOR, 3-STAGE 13B 86312120 -
86319020
86319030
-
-
VAC HOUSING, 2-STAGE
VAC HOUSING, 3-STAGE
SERIAL NO.
FROM
NOTES
2-STAGE
3-STAGE
INCLUDES 12, 13A
INCLUDES 12, 13B only
86322410 NINJA WARRIOR 500 PSI 43
44
Wiring - 2 Stage Vacuum
-VACUUM
SWITCH
-POWER
CORD
BLK
-FUSE
4AMP
1
GRY-WHT
GRN
WHT
BLK for
Old
-CB
13AMP version
BLU/1
-TERMINAL
BLOCK
BLK-WHT
-VACUUM
SWITCH
-CB
13AMP
BLU-BLK/2
-PUMP
SWITCH
GRY/3
GRN
WHT only
WHT
-RECTIFIER
~
~
RED FROM PUMP
-VACUUM
MOTOR
M
WHT/7
-VACUUM
MOTOR
M
WHT/8 RED
M
BLK
-PUMP
MOTOR
GRN GRN GRN
BLK FROM PUMP
86322410 NINJA WARRIOR 500 PSI
REF PART NO.
PRV NO.
QTY
1 98407900 1
DESCRIPTION
HARNESS KIT, SINGLE CORD
Wiring - 2 Stage Vacuum
SERIAL NO.
FROM
NOTES for
Old reference only
86322410 NINJA WARRIOR 500 PSI 45
Wiring - 3 Stage Vacuum
-POWER
CORD
-POWER
CORD
-VACUUM
SWITCH
-PANEL
-VACUUM
SWITCH
-PUMP
SWITCH for
Old reference
MOTOR only
MOTOR MOTOR
46 86322410 NINJA WARRIOR 500 PSI
REF PART NO.
PRV NO.
QTY
1 98407910 1
DESCRIPTION
HARNESS KIT, DUAL CORD
Wiring - 3 Stage Vacuum
SERIAL NO.
FROM
NOTES for
Old reference only
86322410 NINJA WARRIOR 500 PSI 47
Wiring with Heat
1 for
Old reference only
48 86322410 NINJA WARRIOR 500 PSI
REF PART NO.
PRV NO.
QTY
1 98407920 1
DESCRIPTION
HARNESS KIT, HEATED
Wiring with Heat
SERIAL NO.
FROM
NOTES for
Old reference only
86322410 NINJA WARRIOR 500 PSI 49
Suggested Spare Parts
PART NO.
PRV NO.
DESCRIPTION
86199240 250-33A BPR REPAIR KIT PUMPTEC
86317510 THERMOSTAT W/ VERT SPADE
86201790 130-14C THERMOSTAT RESET 302
86135320 140687 BRUSH SET, 120V VAC
86199430 040-03 CASTER SWIVEL 4” 250# CAPACITY
86002620 260-64A ACCESS COVER CLEAR 6” W/RIM
86319110
86319100
-
-
FUSE, 1/4” X 1-1/4”, 4A
FUSE, 1/4” X 1-1/4”, 15A
86318760
86318770
86007140
86317850
86309790
86001660
86007970
-
-
-
Old
WHEEL, 12” X 2.25”
41236 HUBCAP, 5/8” SHAFT
73864
VAC ASSY 2-STG, 120V
72130 SWITCH, SPST 2-POSITION ROCKER
SWITCH, LIGHTED 2-POSITION ROCKER for
86201040 250-73C CAM & BEARING KIT
86201080 250-75A PLUNGER & SEALS KIT version
86201030 250-73B VALVE & O RINGS KIT
86324290 PRIMING HOSE
86006350
86357300
67029
-
RECTIFIER, BRIDGE
TERMINAL STRIP, 12 POST IDEAL
SERIAL NO.
FROM
NOTES
(HEATED MODELS)
(HEATED MODELS)
(HEATED MODELS)
(2-STG MODELS)
(3-STG MODELS)
(HEATED MODELS)
CUT TO FIT only
50 86322410 NINJA WARRIOR 500 PSI
REF.
NO.
1 N/A
MODEL: SERIAL #
Serial Numbers for
Old reference only
86322410 NINJA WARRIOR 500 PSI 51
Notes: for
Old reference only
52 86322410 NINJA WARRIOR 500 PSI
New Machine Warranty
Limited Warranty
CENTURY 400 warrants new machines against defects in material and workmanship under normal use and service to the original purchaser. Any statutory implied warranties, including any warranty of merchantability or fitness for a particular purpose, are expressly limited to the duration of this written warranty. CENTURY 400 will not be liable for any other damages, including but not limited to indirect or special consequential damages arising out of or in connection with the furnishing, performance, use or inability to use the machine. This remedy shall be the exclusive remedy of the buyer. The warranty period is subject to the conditions stated below.
Warranty: Ten Years Polyethylene (PE) Housings, 1 Year Parts,
Subject to conditions outlined below, CENTURY 400 warrants rotationally molded PE housings on all of its machines to be free from defects in material and workmanship, under normal use and service for ten (10) years to the original owner.
Under this warranty we guarantee the performance of non-polyethylene parts and components to be free from defects for up to one (1) year to the original end user. Parts replaced or repaired under this warranty are guaranteed for the remainder of the original warranty period. (See table below)
Service labor charges are covered for up to ninety (90) days from the date of purchase through authorized Windsor service provider.
No travel coverage is extended for cord-electric models. See table below for each general product model warranty coverage.
Ninja, Sensei, Spot Plus,
Hurricane and Turbo Mist for
Old
10 years version
1 year
Service Labor
90days
Travel
None
Polishers / Elec. Burnishers - 3 years 90days None
All others
UPV12 Upright Vacuum
5 years
Vacuum motor, belts – 2 years
1 year
All other parts 1 year
90days
90days
None
None
Product exceptions and Exclusions:
• Extractor brush motors, pump motors. ALL PC boards and electronics, ALL Vacuum motors (Except UPV12). ALL pumps carry a one (1) year parts warranty. only
Normal wear items and accessories including, but not limited to, carbon brushes, castors, clutches, cords, filters, finishes, gaskets, hoses light bulbs, rectifiers, switches, squeegees, bearings, pulleys, relays, actuating cables, wheels, tires, quick disconnects, o-rings, seals, diaphragms, thermostats, and brass fittings will be warranted for manufacturing defects for 90-days from the purchase date for parts only.
90 day unlimited warranty:
Any equipment that fails due to a manufacturing defect within the first 90 days from date of purchase will have an unlimited warranty, which includes parts, standard freight, and labor. Labor or freight will not be covered after 90 days from the date of purchase.
The warranty commences on the purchase date by the original end user from an authorized Century 400 agent, subject to proof of purchase. The machine Registration Card must be completed and returned immediately at the time of purchase. If proof of purchase cannot be identified, the warranty start date is 90 days after the date of sale to an authorized Century 400 distributor. Parts replaced or repaired under warranty are guaranteed for the remainder of the original warranty period.
Century 400, reserves the right to change its warranty policy without notice – 86039960-B PRV NO 98868 10/17/08
Century 400 Inc
. ● 1351 W. Stanford Ave., Englewood, CO 80110 ● (303) 762-1800 ● 800-444-7654 ● FAX (303) 865-2794
1 of 2
New Machine Warranty
90 Day Warranty Extension Available
Upon receipt of the Machine Registration Card, Century 400 will extend by 90 days, from the date of purchase, all items included under the one-year provision. This applies only to one-year items and does not include 90-day wear items.
This Warranty Shall Not Apply To:
1. Any product that has been subject to abuse, misuse, neglect or unauthorized alteration (including the use of incompatible or corrosive chemicals or overloading of capacity).
2. Damage caused by exposure to freezing temperatures.
3. Products that have experienced shipping or freight damage.
4. Repairs necessary to correct any failure due to improper pre-delivery service and inspection by the selling dealer.
5. Time for cleaning units in preparation for repair.
6. Any repairs resulting from poor initial service work or improper diagnosis.
7. Any design alterations performed by an organization not authorized or specified by CENTURY 400. washing..
9. Damage due to electrical components exposed to moisture. for
Old version
Use Of Parts Not Approved By Century 400 Will Void All Warranties
This warranty is valid only for all products sold after October 17, 2008. A product sold before that date shall be covered by the limited warranty in effect at the date of sale to the original purchaser. only
Century 400, reserves the right to change its warranty policy without notice – 86039960-B PRV NO 98868 10/17/08
Century 400 Inc
. ● 1351 W. Stanford Ave., Englewood, CO 80110 ● (303) 762-1800 ● 800-444-7654 ● FAX (303) 865-2794
2 of 2

Public link updated
The public link to your chat has been updated.
Advertisement