STM32651306

STM32651306
STEVAL-IDZ301V1
STEVAL-IDZ302V1
Demonstration board for the SPZB32W1 series
of IEEE 802.15.4 ZigBee® radio communication modules
Data brief
Features
■
Integrated RF module belonging to the
SPZB32W1 series of IEEE 802.15.4 ZigBee®
modules
■
20-pin JTAG connector for programming and
debugging purposes
■
Hardware support for application development:
– Temperature sensor
– Circuitry for measuring the battery voltage
– Two configurable push buttons
– Two configurable LEDs
■
Mini-USB connector and USB-RS-232 bridge
■
Reset push button allows DC power source
selection between the external power supply or
external USB supply
■
LED power indicator
■
Jumper for boot activation
■
Jumpers for serial communication setup
(RS232 or mini-USB)
■
24-pin, double-row header for access to the
remaining STM32W GPIO signals and
interfaces
■
The kit contains a software library including
utilities and application samples
STEVAL-IDZ30xV1
the packages available from the ST website for
ZigBee PRO, Zigbee RF4CE and simplified MAC
of the STM32W108 microcontroller family.
Table 1.
Device summary
Order code
Module
STEVAL-IDZ301V1
SPZB32W1A2
STEVAL-IDZ302V1
SPZB32W1C2
Description
The STEVAL-IDZ30xV1 is a demonstration board
of the SPZB32W1 series of IEEE 802.15.4
ZigBee® RF modules based on the
STM32W108CU6 microcontroller that integrates
a 32-bit ARM® Cortex™ - M3 microprocessor and
a 2.4 GHz, IEEE 802.15.4 radio.
The STEVAL-IDZ30xV1 kit allows testing the
performance of the RF, the features of the
protocol libraries defined for the microcontroller,
and prototyping the target application. The kit
includes a development board and a software
library that can be integrated in the structure of
September 2011
Doc ID 022056 Rev 1
For further information contact your local STMicroelectronics sales office.
1/6
www.st.com
6
Block diagram, schematic and main components
STEVAL-IDZ301V1, STEVAL-IDZ302V1
1
Block diagram, schematic and main components
1.1
Block diagram
Figure 1.
Steval-IDZ30xV1 HW block diagram
STLM75
2/6
Doc ID 022056 Rev 1
STEVAL-IDZ301V1, STEVAL-IDZ302V1
Block diagram, schematic and main components
1.2
Schematic
Figure 2.
STEVAL-IDZ30xV1 schematic
Doc ID 022056 Rev 1
3/6
Block diagram, schematic and main components
1.3
Main components
Figure 3.
STEVAL-IDZ30xV1 - main components
IMD9A
Power Led
STEVAL-IDZ301V1, STEVAL-IDZ302V1
STLM75
Conf. buttons
Reset
Conf.
Leds
Power Jack
Boot
Jmp
Power
JMP
FT
MiniUSB
RS232/USB
Bridge
Serial
JMP
24 pin Exp.
Connector
SPZB32W1xx.0
JTAG Connector
AM09230V1
4/6
Doc ID 022056 Rev 1
STEVAL-IDZ301V1, STEVAL-IDZ302V1
2
Revision history
Revision history
Table 2.
Document revision history
Date
Revision
23-Sep-2011
1
Changes
Initial release.
Doc ID 022056 Rev 1
5/6
STEVAL-IDZ301V1, STEVAL-IDZ302V1
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
6/6
Doc ID 022056 Rev 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement