VIP Security System
TOYOTA
TACOMA
2009 -
TVIP V5
Preparation
RS3200 PLUS
Part Number: PT398-35090
NOTE: Part number of this accessory may not be
the same as the part number shown.
Kit Contents
Item #
1
2
3
4
5
6
7
8
Quantity Reqd.
1
1
1
1
2
2
1
1
Description
Wire Harness
Security ECU
GBS ECU
Status Monitor/Microphone
Warning Labels (English)
Warning Labels (Spanish)
Owner’s Manual
Warranty Card
Hardware Bag Contents
Item #
1
2
3
4
5
6
Quantity Reqd.
1
1
1
4
15
15
Description
ECU Mounting Bracket
Bolt
Large Foam Tape Strip (2 pcs.)
Small Foam Tape Strips
Medium Wire Ties
Large Wire Ties
Additional Items Required For Installation
Item #
1
Quantity Reqd.
1
Description
Lint-free Cloth
Special Chemicals
Cleaner
Glass Cleaner
VDC Approved Cleaner
Household Glass Cleaner
General Applicability
Note: Tacoma with Remote keyless Entry.
Recommended Sequence of Application
Item #
1
2
3
Accessory
Audio
Trailer Wire Harness
V5
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Item #
1
2
3
4
5
Quantity Reqd.
3
5
2
4
4
Description
Clips – lower dash cover
Clips – audio panel
Clips – glove box inner cover
Clips – center cluster panel
Clips – small cover lower IP
Legend
Conflicts
Note: Must not be installed in vehicles with factory Antitheft alarm.
Recommended Tools
Personal & Vehicle
Protection
Notes
Safety Glasses
Safety Gloves
Vehicle Protection
Optional
Blankets, Part Boxes
Special Tools
Notes
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
Striker Tool (PPO Only)
CAD-E IADS P/N
ALL02-016-01
Grabber Tool (Flexible Pick- (CAD-E IADS P/N
up Tool)
COR02-016-01 (PPO))
ECU Pin Remover Tool
Toyota SST: 1276565-1
Installation Tools
Notes
Screwdriver
#2 Phillips, Flat Blade
Jeweler’s
10 mm, extension
36 in•lbf (4.1 N•m)
e.g. Panel Pry Tool #1
Socket
Torque Wrench
Nylon Panel Removal Tool
Toyota SST # 00002-06001-1
Cloth
Side Cutter
Tape
Issue: A
Lint-free
03/13/08
Masking, Electrical, Clear
Page 1 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
1. Vehicle Disassembly.
10mm Socket
Negative Battery
Cable
(a) Place Automatic Vehicles in low gear with
the parking brake set.
(b) Remove the negative battery cable.
(Fig. 1-1)
(1) Protect the fender before starting.
(2) Note the Cable Position as it will be reinstalled
in the same position.
Fig. 1-1
CAUTION: Do not touch the positive terminal.
Nylon Panel Removal Tool
Nut
Foot Rest
(c) Remove the driver side foot rest, and the
driver side step cover. (Fig. 1-2)
(1) Cover the floor and seats before starting.
Cowl Cover
NOTE: The foot rest can be easily damaged.
Step Cover
(d) Remove driver side cowl cover. (Fig. 1-2)
Fig. 1-2
(1) Remove the nut securing the cowl cover.
Nylon Panel Removal Tool,
10 mm Socket
M/T MODELS
Lower Dash
Cover
Cover
FOR M/T VEHICLE MODELS ONLY.
(Steps e-g)
(e) Remove the small cover from the lower dash
cover’s right side. (Fig. 1-3)
(f) Remove the hood release cable. (Fig. 1-3)
(g) Remove the lower dash cover. (Fig. 1-3)
Hood Release
Lever
Fig. 1-3
Issue: A
Bolt
Bolt
03/13/08
Page 2 of 21 pages
(1) Open the screw cover of the lower dash cover.
(2) Remove the two bolts securing the cover.
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
Nylon Panel Removal Tool,
10mm Socket
A/T MODELS
Cover
Lower Dash
Cover
FOR A/T VEHICLE MODELS ONLY.
(Steps h-j)
(h) Remove the small cover from the lower dash
cover’s right side. (Fig. 1-4)
(i) Remove the hood release cable. (Fig. 1-4)
Hood Release
Lever
Fig. 1-4
(j) Remove the lower dash cover. (Fig. 1-4)
(1) Open the screw cover of the lower dash cover.
(2) Remove the two bolts securing the cover.
Bolt
Bolt
Bolt (x3)
10mm Socket
(k) Remove the metal substructure. (Fig. 1-5)
(1) Remove 3 bolts.
CAUTION: Sharp metal edges.
Fig. 1-5
Metal Substructure
Phillips Screwdriver
Screw
Screw
(l) Remove the two screws securing the lower
steering column cover behind the steering
wheel. (Fig. 1-6)
(1) Insert the key into the ignition switch and turn it
to ON to unlock the steering wheel.
(2) Turn the steering wheel left and right to gain
access to the screws.
Steering Column Cover
Fig. 1-6
(m) Remove the lower steering column cover.
(Fig. 1-7)
Fig. 1-7
Issue: A
Steering Column Cover
03/13/08
Page 3 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
(n) Attach the low adhesion masking tape on the
center cluster panel, as shown. (Fig. 1-8)
Nylon Panel Removal Tool
Center Cluster Panel
Masking Tape
CAUTION: Only apply tape on the Center
Cluster Panel surface.
(o) Using the Nylon Panel Removal Tool,
remove the center cluster panel. (Fig. 1-8)
(1) Loosen the four clips when removing the panel.
(2) Disconnect all connectors from the panel.
Fig. 1-8
10mm Socket
(p) Remove the audio unit. (Fig. 1-9)
Audio Unit
(1) Remove 4 bolts.
(2) Disconnect all connectors from the audio unit.
NOTE: Prior to removing the radio assembly
from the dash, cover the radio mounting tabs
with a cloth to prevent damage to the vehicle.
Audio Unit
Mounting Tabs
Fig. 1-9 Bolts (x4)
Cloth
(q) Remove the knockout cover from the lower
portion of the center console. (Fig. 1-10)
Nylon Panel Removal Tool
Fig. 1-10
Knockout Cover
Nylon Panel Removal Tool
Nut
(r) Remove the passenger side step cover.
(Fig. 1-11)
(1) Cover the floor and seats before starting.
Cowl Cover
(s) Remove the passenger side cowl cover.
(Fig. 1-11)
(1) Remove 1 nut.
Fig. 1-11
Issue: A
03/13/08
Step Cover
Page 4 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
(t) Remove the glove box. (Fig. 1-12)
(1) Remove the dampener from the glove box.
Glove Box
Dampener
Fig. 1-12
(u) Remove the glove box inner cover.
(Fig. 1-13)
10mm Socket
(1) Remove 1 bolt.
Bolt
Inner Cover
Fig. 1-13
Ignition Switch
Vehicle's 8P
(White)
2. V5 Harness Installation.
(From Center Cluster Area to Driver Side
Cowl Area)
(a) Locate and disconnect the white 8P
connector from the ignition switch in the
steering column area. (Fig. 2-1)
Steering Wheel
Fig. 2-1
Side Cutter
Ignition Switch
Large Wire Tie
8P (White)
V5
Harness
Fig. 2-2
Issue: A
large Wire Ties (x2)
03/13/08
(b) Plug in the V5 harness' white 8P connectors
between the ignition switch and the vehicle
harness' white 8P connector.
(c) Secure the white 8P connectors to the
vehicle harness with 1 large wire tie.
(Fig. 2-2)
(d) Secure the V5 harness to the vehicle harness
with 2 large wire ties. (Fig. 2-2)
Page 5 of 21 pages
TOYOTA
TACOMA
2009 -
Procedure
TVIP V5
RS3200 PLUS
13P (Black)
(e) Locate and disconnect the black 13P
connector, and two white 18P connectors
from the driver side J/B. (Fig. 2-3)
18P (White)
J/B
18P (White)
Fig. 2-3
Side Cutter
18P
18P
(f) Secure the 13P(black) connectors, 2 18P
connectors and V5 Harness to the vehicle
harness with 5 medium Wire Ties, in front
of the driver side J/B. (Fig. 2-5)
13P (Black)
(1) Align the V5 harness’ branch point to the end of
the corrugated tube of the vehicle harness.
Fig. 2-5
medium Wire Ties (x5)
V5
Harness
V5 Harness
(g) Route the V5 harness' white wire terminal,
white 2P connector and white 10P
connectors behind the brace down toward
the driver side cowl area as shown.
(Fig. 2-6)
2P (White)
10P (White)
Wire Terminal
Fig. 2-6 (White)
Issue: A
03/13/08
Page 6 of 21 pages
TOYOTA
TACOMA
2009 -
Procedure
TVIP V5
RS3200 PLUS
Vehicle’s
10P (White)
Tape
Vehicle’s
12P (White)
Fig. 2-7
12P (White)
2P (White)
(1) Verify the connectors are plugged in securely.
10P (White)
WHITE Wire
Terminal
Fig. 2-8
V5 Harness
Tape
(i) Locate the hole in the driver side cowl area,
then pull out the vehicle harness’ white 10P
connector and disconnect it. (Fig. 2-7)
(j) Plug the V5 harness' white 10P connectors
between the vehicle harness' white 10P
connectors, then insert the white 10P
connectors into the hole in the driver side
cowl area. (Fig. 2-8)
V5 Harness
Tape
(h) Locate the vehicle’s white 12P connector in
the driver side cowl area, and remove the
electrical tape from the vehicle’s white 12P
connector, then disconnect it for clearance.
(Fig. 2-7)
Combination
Connector
Connector
Block
(k) Reconnect the vehicle harness’ white 12P
connector and secure it to the vehicle
harness using electrical tape. (Fig. 2-8)
(l) Locate and disconnect the combination
connector from the connector block in the
driver side cowl area. (Fig. 2-9)
2P (White)
WHITE Wire
Terminal
Fig. 2-9
Jeweler’s Screwdriver
8P (White)
Combination
Connector
(m) Using a small jeweler's screwdriver, release
and pull out the white 8P connector from the
combination connector. (Fig. 2-10)
(1) Turn the connectors so the pins face you.
Fig. 2-10
Issue: A
03/13/08
Page 7 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
Jeweler's Screwdriver, ECU Pin Removal Tool
8P (White)
WIRE SIDE VIEW
Retainer
Combination
Connector
Vehicle Harness'
WHITE Wire
Terminal
Fig. 2-11
Retainer
WIRE SIDE VIEW
V5 Harness’
WHITE Wire
Terminal
Fig. 2-12
Combination
Connector
(n) Using a small jeweler's screwdriver, lift up
the terminal retainer on the back of the 8P
connector. Locate the WHITE wire in the 8P
connector. Using the ECU pin remover tool
or a small jeweler’s screwdriver, release and
pull out the terminal for the WHITE wire.
(Fig. 2-11)
(1) Do not pull out the retainer.
(2) Turn the connector so the wires face you and the
retainer is on top.
8P (White)
(o) Insert the terminal at the end of the V5
harness' WHITE wire into the seventh space
from the left of the 8P connector, then close
the retainer. Refit the white 8P connector to
the combination connector. (Fig. 2-12)
(1) Turn the connector so the wires face you and the
retainer is on top.
(2) Verify the correct opening is chosen.
(3) Verify the terminal is inserted and seated
properly. The terminal should not come out
when pulled lightly from the back. If the terminal
comes off, then push it in again.
Retainer
(p) Disconnect the empty 2P female connector
plugged into the V5 harness. Using a small
jeweler's screwdriver, lift up the terminal
retainer on the back of the empty 2P
connector. (Fig. 2-13)
Jeweler's Screwdriver
V5 Harness
(1) Do not pull out the retainer.
2P (Female)
Fig. 2-13
2P (Female)
Retainer
Retainer
Vehicle Harness'
WHITE Wire
Terminal
Fig. 2-14
Issue: A
03/13/08
2P (Female)
(q) Insert the terminal at the end of the vehicle
harness' WHITE wire into the right side
opening of the empty 2P connector as
shown, then close the retainer. (Fig. 2-14)
WHITE
WIRE SIDE VIEW
Page 8 of 21 pages
(1) Turn the connector so the wires face you and the
tab is on top.
(2) Verify the correct opening is chosen.
(3) Verify the terminal is inserted and seated
properly. The terminal should not come out
when pulled lightly from the back. If the terminal
comes off, then push it in again.
TOYOTA
TACOMA
2009 -
Procedure
TVIP V5
RS3200 PLUS
Combination
Connector
V5 Harness
2P (White)
(r) Plug in the V5 harness' white 2P male
connector to the white 2P female connector,
and reconnect the combination connector.
(Fig. 2-15)
(1) Verify the connectors are plugged in securely.
(s) Wrap the white 10P connectors in one small
foam tape strip. (Fig. 2-15)
10P (White)
Small Foam
Tape Strip
Fig. 2-15
Combination
Connector
2P (White)
Side Cutter
V5 Harness
Medium
Wire Ties
(x2)
10P (White)
Fig. 2-16
M/T MODELS
Small Foam
Tape Strips
(2x)
Vehicle's
Brace
(t) Secure the white 10P connectors to the
vehicle harness using one medium wire tie.
(Fig. 2-16)
(u) Bundle the excess V5 harness, then using
one medium wire tie, secure the 2P
connectors and V5 harness as shown.
(Fig. 2-16)
3. V5 Harness Installation.
(From Center Cluster Area to Passenger Side
Cowl Area)
FOR M/T VEHICLE MODELS ONLY.
(Step a)
Brake Shaft
Fig. 3-1
(a) Attach two small foam tape strips to the
vehicle's brace as shown. (Fig. 3-1)
(1) (1) Do not attach anything to the brake shaft.
A/T MODELS
FOR A/T VEHICLE MODELS ONLY.
(Step b)
Vehicle's
Brace
(b) Attach one small foam tape strip to the
vehicle's brace as shown. (Fig. 3-2)
Small Foam
Tape Strip
Fig. 3-2
Issue: A
03/13/08
Page 9 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
Grabber Tool
(c) Route the V5 harness toward the center
cluster area using the grabber tool.
(Fig. 3-3)
Grabber Tool
V5 Harness
Brake Shaft
Fig. 3-3
(1) Insert the grabber tool from the center cluster
area and push it toward the driver side upper
brake shaft area.
(2) Catch the V5 harness 10P connectors using the
grabber tool, then pull it back toward the center
cluster area.
(d) Secure the V5 harness’ relay to the vehicle
brace with one large wire tie. (Fig. 3-4)
Side Cutter Tool
Large Wire
Tie
V5 Harness
Relay
Fig. 3-4
Side Cutter
V5 Harness
large Wire Ties (x3)
(e) Route the V5 harness toward the passenger
side glove box area. (Fig. 3-5)
(f) Route the V5’s 4P black connector
downward and out of the open knockout
location. (Fig. 3-5)
14P
(White)
(g) Secure the V5 harness to the vehicle harness
with 3 large wire ties. (Fig. 3-5)
4P
(Black)
Fig. 3-5
(h) Connect the 4P connector to the Status
monitor / Microphone. (Fig. 3-6)
4P (Black)
(i) Push the Status Monitor into the open knock
until it snaps in place. (Fig. 3-6)
Status Monitor /
Microphone
Fig. 3-6
Issue: A
03/13/08
Page 10 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
(j) Pull the excess V5 Harness back up into the
Center Console Area and secure it with 1
large wire tie to the Vehicle Harness.
(Fig. 3-7)
Side Cutter
large Wire Tie
V5 Harness
Fig. 3-7
V5 Harness
Side Cutter
Large Wire Tie
14P (White)
(k) Plug in the V5 14P male connector to the
vehicle 14P female connector. Bundle the
excess portion of the vehicle harness, then
secure the V5 harness and vehicle harness
with 1 large Wire Tie. (Fig. 3-8)
(1) Verify the connectors are plugged in securely.
Fig. 3-8
Side Cutter
Large Wire Tie
Reinforcement
Fixation
(l) Secure the V5 harness to the vehicle harness
with 1 medium Wire Tie. (Fig. 3-9)
(m) Route the V54 harness behind the
reinforcement fixation securing it with 1
large Wire Tie. (Fig. 3-9)
V5 Harness
Fig. 3-9
Medium Wire Tie
Tape
Vehicle's 4P
(White)
4P (White)
(n) Locate the vehicle harness' white 4P female
connector and remove the tape securing the
4P connector. (Fig. 3-10)
V5 Harness
Fig. 3-10
Issue: A
03/13/08
Page 11 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
Side Cutter
Medium Wire Ties (x3)
4P (White)
V5 Harness
(o) Plug in the V5 harness' white 4P male
connector to the vehicle harness' white 4P
female connector. Secure the V5 harness
and white 4P connectors to the vehicle
harness with three medium wire ties.
(Fig. 3-11)
(1) Verify the connectors are plugged in securely.
Fig. 3-11
Side Cutter, Flat
blade Jewelers
Screwdriver
V5 Harness
Vehicle's
Clip
(p) Route and secure the V5 harness to the
vehicle harness with two medium wire ties
and the vehicle's wire clip. (Fig. 3-12)
8P (White)
40P (White)
Fig. 3-12
Medium Wire Ties (x2)
(q) Locate and disconnect the grey 11P
connector to the connector block of the
passenger side cowl area. (Fig. 3-13)
Vehicle’s
11P (Grey)
Connector
Box
Fig. 3-13
Tape
(r) Locate the vehicle’s outer white 10P
connector in the passenger side cowl area,
and remove the tape from the vehicle’s
white 10P connector, then disconnect it for
clearance. (Fig. 3-14)
Vehicle Harness’
Outer 10P (White)
(s) Locate the hole in the passenger side cowl
area, then pull out the vehicle harness’ inner
white 10P connector and disconnect it.
(Fig. 3-14)
Vehicle’s Inner
10P (White)
Fig. 3-14
Issue: A
03/13/08
Connector
Box
Page 12 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
Vehicle’s
10P (White)
V5 Harness
Connector
Box
V5 Harness’
10P (White)
(t) Plug in the V5 10P connectors between the
vehicle inner 10P connectors. (Fig. 3-15)
(1) Both the inner and outer white 10P connectors fit
the V5 harness. Use the inner white connector.
(u) Insert V5 grey 11P connectors between the
vehicle grey 11P connector and the
connector block. (Fig. 3-15)
Foam
Tape
11P (Grey)
Fig. 3-15
Side Cutter
(v) Place the inner white 10P connectors in the
concave spot of the cowl area. (Fig. 3-15)
V5 Harness
10P (White)
Medium Wire
Ties (x2)
11P (White)
Large Wire Tie
(w) Reconnect the vehicle outer 10P connector
and secure to the vehicle harness using 1
small Foam Tape. (Fig. 3-15)
(x) Reconnect the vehicle’s outer white 10P
connector and secure it to the vehicle
harness using the electrical tape. (Fig. 3-16)
(y) Secure the V5 harness to the vehicle harness
with two medium wire ties. (Fig. 3-16)
Fig. 3-16
V5 Security ECU
(z) Secure the white 11P connectors to the
vehicle harness with one large wire tie.
(Fig. 3-16)
4. V5 Security ECU and V5 GBS ECU
Installation.
ECU Mounting
Bracket
Fig. 4-1
(a) Insert the V5 security ECU mounting
bracket tab into the indicated bracket slot on
the V5 security ECU. (Fig. 4-1)
(1) Insert the mounting bracket into the correct slot;
you have only one chance to install it properly.
Flat blade Jewelers Screwdriver
V5 GBS ECU
CAUTION: Due to a tight fit between the V5
ECU and bracket, it may be necessary to support
the bracket on a flat surface corner and press the
ECU onto the bracket.
(b) Turn the adjustment screw on the V5 GBS
ECU to the "8" position. (Fig. 4-2)
Fig. 4-2
Issue: A
03/13/08
Page 13 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
V5 GBS ECU
Large Foam
Tape Strips (x2)
(d) Insert the V5 GBS ECU mounting bracket
tab into the indicated bracket slot on the V5
GBS ECU. (Fig. 4-3)
V5 GBS ECU
(1) Insert the mounting bracket into the correct slot;
you have only one chance to install it properly.
ECU Mounting
Bracket
V5 Security ECU
Fig. 4-3
Vehicle Brace
Small Foam
Tape
V5 Harness
(c) Apply two large foam tape strips to the V5
GBS ECU as shown. (Fig. 4-3)
V5 GBS ECU
(e) Connect the V5 harness’ white 40P
connector and white 8P connector to the V5
security ECU and V5 GBS ECU. (Fig. 4-4)
(1) Verify the connectors are plugged in securely.
(f) Apply one small foam tape strip to the
vehicle brace as shown. (Fig. 4-4)
8P (White)
Fig. 4-4
40P (White)
V5 Security ECU
10mm Socket
V5 Security
ECU
V5 GBS ECU
(g) Using the supplied bolt, secure the V5
security ECU and V5 GBS ECU to the
reinforcement fixation. (Fig. 4-5)
V5 Harness
Reinforcement
Bolt (Supplied)
Fig. 4-5
Side Cutter
V5 Security
ECU
V5 GBS ECU
(h) Secure the V5 ECU harness and the GBS
ECU portion of the V5 harness to the
vehicle harness with one large wire tie.
(Fig. 4-6)
V5 Harness
Wire Tie
Fig. 4-6
Issue: A
03/13/08
Page 14 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Procedure
RS3200 PLUS
5. Warning Label Installation.
Clear Tape
●
10mm
Line Up With Bottom
of Window Etching
(a) Using Household Windex, clean the inside
of the Front Door Windows. (Fig. 5-1)
Warning Label
Fig. 5-1
●
For US Vehicles use the English Labels and Tag, and
discard the Spanish Tags and Labels.
For Mexico Vehicles use the Spanish Labels and Tag,
and discard the English Tags and Labels.
(b) Place the Window Labels on the inside of
the Front Door Windows as shown.
(Fig. 5-1)
(1) Use a piece of clean adhesive tape to lift the
Labels off their protective backing.
Clear Tape
CAUTION: Do not touch the adhesive surface.
Line Up With Bottom
of Other Label
1-5mm
(1) Line up the Labels properly and place on the
Glass. Do not attempt to reposition the Labels
once they and place.
If Labels are being installed with other Window
Label’s align them as shown in Fig. 5-2.
Warning Label
Other Label
Fig. 5-2
6. Completing the Installation.
(a) Complete the reassembly of the vehicle.
(1) Prior to replacing the radio assembly into the
dash, cover the radio mounting tabs with a cloth
to prevent damage to the vehicle.
(2) Reconnect any disconnected connectors.
(3) Verify the panels fit together properly with no
uneven gaps between them.
(b) Clean up and remove any trash.
Torque Wrench
Negative Battery
Cable
(c) Reconnect the vehicle's negative battery
cable. (Fig. 6-1)
(1) Position the negative battery cable at the original
factory position.
(2) Tighten the nut to 36 in•lbf (4.1 N•m).
CAUTION: Do not touch the positive terminal.
Battery
Fig. 7-1
Issue: A
03/13/08
(d) Place the owner's manual and warranty card
(left in their protective bags) in the glove
box.
Page 15 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Checklist - these points MUST be checked to ensure a quality installation.
Check:
RS3200 PLUS
Look For:
Accessory Function Checks
Fit appropriate fuse before beginning.
Press and release the remote control’s lock
1. The turn signal lights flash once.
button to start the system’s arming process.
All doors lock.
The Status Monitor’s LED lights up.
Wait 30 seconds.
2. After 30 seconds, the LED starts flashing;
the system is now armed.
Press and release the remote control’s
3. The turn signal lights flash twice.
unlock button to disarm the system.
The driver’s door unlocks.
The LED stops flashing.
The interior lights turn on.
Open the driver's door, insert the key
into the ignition switch and turn it to
“ON”. Roll down all the windows,
remove the key and exit the vehicle.
Arm and disarm the system with the remote
4. The doors automatically relock.
again, then wait 30 seconds.
The system automatically starts the arming
process.
Press and release the remote control’s
5. Refer to step number 3.
unlock button again to stop the arming
process.
Insert the key into the driver’s door key
6. All doors lock.
cylinder and turn it toward the front of the
The LED lights up.
vehicle to start the arming process.
Wait 30 seconds.
7. After 30 seconds, the LED starts flashing;
the system is now armed.
Issue: A
03/13/08
Page 16 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Checklist - these points MUST be checked to ensure a quality installation.
Check:
RS3200 PLUS
Look For:
Reach inside and manually unlock the
8. The driver's door automatically relocks.
driver's door to trigger an alarm.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The LED lights up.
The interior lights turn on.
Manually unlock the driver's door again and
9. The driver's door lock attempts to lock
hold it unlocked, open the door, then sit in
repeatedly.
the driver's seat.
The horn continues to sound repeatedly.
The headlights, turn signal lights continue
flashing.
The LED remains on.
The interior lights remain on.
Insert the key into the ignition switch and
turn it to “START” to stop the alarm.
10. The horn stops sounding.
All the lights stop flashing and/or turn off.
The LED turns off.
Turn the key back to “LOCK”, remove
it, and then exit the vehicle.
With the door open, press the lock switch
The starter cranks and the engine starts.
11. All doors lock.
The LED lights up.
on the door to lock the doors, and then
close the door to start the system's arming
process.
12. After 30 seconds, the LED starts flashing;
the system is now armed.
Wait 30 seconds.
13. The front passenger's door relocks.
Reach inside and manually unlock the front
The horn sounds repeatedly.
passenger's door to trigger an alarm.
The headlights, turn signal lights flash
repeatedly.
The LED lights up.
The interior lights turn on.
Issue: A
03/13/08
Page 17 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Checklist - these points MUST be checked to ensure a quality installation.
Check:
RS3200 PLUS
Look For:
Press and release the remote control's
14. The horn stops sounding.
unlock button to stop the alarm.
All the lights stop flashing.
The LED turns off.
For D-cab only
Press and release the remote control's lock
15. Refer to step number 1 and number 2.
button to start the arming process, and then
wait 30 seconds until the system is armed.
Unlock and open one of the rear passenger
16. Refer to step number 13.
doors to trigger an alarm.
Repeat the above steps with the other rear
17. Refer to step number 15 and number 16.
passenger door.
Roll up all windows, remove the key and
exit the vehicle.
Press and release the remote control's lock
18. Refer to step number 1.
button to start the arming process.
Wait 30 seconds.
19. After 30 seconds, the LED starts flashing;
the system is now armed.
Perform the following check in a
temperature-controlled environment
(50° – 90° F.)
With the tip of key (or striker tool pulled all
20. The horn sounds repeatedly.
the way out (PPO only)), tap the center of
The headlights flash repeatedly.
the driver's door window to trigger the warn
The turn signal lights flash repeatedly.
away alarm.
The LED lights up.
NOTE: Adjust as necessary by increasing
the GBS setting to the next level if the
alarm does not trigger during the functional
verifications.
NOTE: If you do not disarm the system,
the alarm will last 20 seconds. It is not
necessary to check the alarm duration.
Issue: A
03/13/08
Page 18 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Checklist - these points MUST be checked to ensure a quality installation.
Check:
RS3200 PLUS
Look For:
Insert the key into the driver’s door key
21. The horn stops sounding.
cylinder and turn it toward the back of the
All the lights stop flashing and/or turn off.
vehicle to stop the alarm.
The status monitor’s LED turns off.
Vehicle Function Checks
Head Lights
Functioning Head Lights
High Beams
Functioning High Beams
Turn Signal Lights
Functioning Turn Signal Lights
Tail Lights
Functioning Tail Lights
Stop Lights
Functioning Stop Lights
Backup Lights
Functioning Backup Lights
Hazard Lights
Functioning Hazard Lights
Marker Lights
Functioning Marker Lights
Dome/Courtesy/Map Lights
Functioning Dome/Courtesy/Map Lights
Panel/Switch Illumination
Functioning Controls/Illumination
Accessory Controls/Illumination (if
Functioning Accessory Controls
equipped)
Key Sensor Buzzer
Functioning Key Sensor
Fog Lights (if equipped)
Functioning Fog Lights
Daytime Running Lights (if equipped)
Functioning DR Lights
Trunk/Tailgate/Bed Lights (if equipped)
Functioning Lights
Glove Box Light (if equipped)
Functioning Glove Box Light
Cruise Control Light (if equipped)
Functioning Cruise Control Light
Issue: A
03/13/08
Page 19 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Checklist - these points MUST be checked to ensure a quality installation.
RS3200 PLUS
Check:
Look For:
Seat Belt Warning Light
Functioning Seat Belt Warning Light. If the
warning light remains on, it may indicate a
system malfunction.
Functioning Air Bag Warning Light. If the
Air Bag Warning Light
warning light remains on, it may indicate a
system malfunction.
Functioning ABS Light. If the warning light
ABS Light (if equipped)
remains on, it may indicate a system
malfunction.
Lamp Failure Sensor (if equipped)
Functioning Lamp Failure Light. If the
warning light remains on, it may indicate a
system malfunction.
Track/Skid Control Light (if equipped)
Functional Track/VSC Light. If the warning
light remains on, it may indicate a system
malfunction.
HVAC
All HVAC Controls Function
Power Locks (if equipped)
Functioning Power Locks
Power Windows (if equipped)
Functioning Power Windows
Power Seats (if equipped)
Functioning Power Seats
Power Sunroof (if equipped)
Functioning Sunroof
Horn
Functioning Horn
Gauges
Functioning Gauges
Front Wiper/Washer
Functioning Front Wiper/Washer
Rear Wiper/Washer (if equipped)
Functioning Rear Wiper/Washer
Clock (if equipped)
Functioning Clock
Issue: A
03/13/08
Page 20 of 21 pages
TOYOTA
TACOMA
2009 -
TVIP V5
Checklist - these points MUST be checked to ensure a quality installation.
RS3200 PLUS
Check:
Look For:
Accessory Power Socket (if equipped)
Functioning Power Socket
Starter
Functioning Starter
Audio/Video (if equipped)
Functioning Audio/Video
Power Sliding Door (if equipped)
Functioning Power Sliding Door
Convenience Memory Settings (if
Functioning Memory Settings
equipped)
Heated Seats (if equipped)
Functioning Heated Seats
Massage Seats (if equipped)
Functioning Massage Seats
Rear Window Defogger (if equipped)
Functioning Rear Window Defogger
Power Side Mirrors (if equipped)
Functioning Power Side Mirrors
Side Mirror Defogger (if equipped)
Functioning Side Mirror Defogger
Front Windshield Defogger (if equipped)
Functioning Front Windshield Defogger
Navigation System (if equipped)
Functioning Navigation System
Steering Column Check (if equipped)
Functioning Steering Column
Remove the appropriate fuse after
checks are completed.
Issue: A
03/13/08
Page 21 of 21 pages
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement