48610 FlexMod LVD Installation Guide

48610 FlexMod LVD Installation Guide
FlexMod™ LVD Low Voltage
Disconnect
48610
48610-OX
48710
48710-OX
LVD
LVD Kit
Programmable LVD
Programmable LVD Kit
For 12V and 24V DC systems, 10A at 85°C
Normal Operation Summary
Connections
(using the 12805 Mating Connector Kit)
Warning: Disconnect the vehicle’s battery before
installation.
Required Connections:
1. Connect pin 4 (BATT+) to an appropriately
sized fuse. Connect the fuse to the positive
terminal of the battery.
2. Connect pin 3 (LOAD+) to the positive side of
the load.
3. Connect pin 2 (GND) to ground.
4. To ensure proper environmental sealing, all
unused connector pins must be sealed with
blanking pins (see specifications section).
(24V limits in parentheses)
Note: this summary describes the factory default settings.
Programmable units may have different voltage and or
time delays.
1. When BATT+ voltage is above 13.0V (26.0V) for 10
seconds, the LVD will automatically connect the loads to
the battery.
2.When BATT+ voltage drops below 12.1V (24.2V) for 60
seconds, the Alarm will pulse, warning the user that the
loads are about to be disconnected.
• The operator has the option to Override the imminent disconnect by activating the Override signal (see Additional Operating Detail).
3. After 60 seconds of the alarm pulsing, the loads will
disconnect and the alarm will turn offt.
Optional Connections:
1. Connect pin 5 (OVERRIDE) to a normally open
momentary switch. Connect the other side of the
switch to BATT+.
2. Connect pin 6 (ALARM) to an audible/visual alarm.
Connect the other side of the alarm to ground.
Littelfuse Commercial Vehicle Products
www.colehersee.com
www.littelfuse.com
IF-163 Rev E
Additional Operating Details
Override: The Override signal is activated
when the operator momentarily connects
pin 5 (Override) to BATT+. This is normally
accomplished with a momentary switch. The
Override signal serves different functions
depending on when it is activated.
• If the load current exceeds 15 amps (and is less
than 17 amps) for one second, the load output
will be turned off and the alarm will repeat a
cycle of pulsing the alarm twice followed by a
pause. To reset from the fault, either
• While the Alarm is pulsing, activating the
Override signal will delay the imminent
disconnect, keeping the loads on for an
additional 15 minutes. After the 15 minute time
period, the LVD will resume monitoring battery
voltage. Activating Override again before the 15
minute timeout will turn the loads off, putting the
LVD in storage mode, (see paragraph b.).
• If the COIL+ current exceeds 15 amps (and is
less than 17 amps) for one second, the COIL+
output will be turned off and the STATUS output
will repeat a cycle of pulsing the STATUS output
twice followed by a pause. To reset from the
fault, either press BOOST for 10 seconds or cycle
power.
• If the operator activates Override while the load
is on, the LVD will enter storage mode and turn
the load off. The only way to turn on the load
from storage mode is to activate Override again.
This is often used when storing a vehicle for a
long period.
Abnormal Voltage
• When Override is activated while the LVD is
off due to low battery voltage, the loads will
toggle on. After 15 minutes, the LVD will resume
monitoring battery voltage. If during the 15
minute period the battery voltage rises above the
upper limit for ten seconds, the 15 minute delay
is exited and the LVD resumes monitoring battery
voltage.
press manual or cycle power.
Abnormal Voltage: If the BATT+ voltage is less
than 7.5V (16V) or greater than 17V (34V), the load
output will be turned off and the alarm will repeat
a cycle of pulsing the alarm three times followed
by a pause. The LVD will auto-recover when
BATT+ returns to normal.
Programmable Versions
Use Cole Hersee Programmer Kit 48650 using
cable assembly 65373 (included in kit).
Overcurrent Protection
• If the load current exceeds 31 amps, the load
output will be turned off and the alarm will be
turned on. To reset from the fault, the LVD’s
power must be cycled.
• If the load current exceeds 17 amps (and is less
than 31 amps) for one second, the LOAD output
will be turned off and the alarm will repeat a
cycle of pulsing the alarm twice followed by
a pause. To reset from the fault, either press
manual or cycle power.
Littelfuse Commercial Vehicle Products
www.colehersee.com
www.littelfuse.com
IF-163 Rev E
General Specifications
Environmental: SAE J1455 & J1113
Sealed to IP67
Electrical:
9-32VDC
10A max. Load Circuit Current 200mA max. Alarm Circuit Current
2mA max quiescent current
Accuracy:
+/- 50 mV
Mating Connector: Deutsch DT06-08S, Amphenol AT06-08S
Blanking Pin:
Deutsch 114017, Amphenol A114017
Auxiliary
Load
Battery
Fuse
Optional
LED
1
2
3
4
Optional
Momrntary
Switch
5
1
8
7
6
6
4
5
3
2
Connector pin descriptions:
1.
AUX BATT+
2.GROUND
3.COIL+
4.
MAIN BATT+
5.BOOST
6.STATUS
7.
REDUNDANT GROUND
8.
REDUNDANT GROUND
LVD Accessories available
from Cole Hersee
12805:
Mating connector kit
58332-03
Rocker Switch with Indicator
55020-02: Toggle Switch
55020-04:
PVC Coated Toggle Switch
9216-03:Momentary Switch
9187-02:
Momentary Push Button Switch
PL-612-R:
12V Red LED Indicator Light
MA-250012-RS: 12V Relay for Alarm Circuit
MA-150024-RS: 24V Relay for Alarm Circuit
Submit technical questions to:
[email protected]
Littelfuse Commercial Vehicle Products
www.colehersee.com
www.littelfuse.com
IF-163 Rev E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement