CONSTRUCTO10

CONSTRUCTO10
HEAT
RECOVERY VENTILATOR
CONSTRUCTO 1.0 HRV
Part no. 41502 (PORTS
Part no. 41500 (PORTS
ON TOP)
ON SIDES)
45 to 104 CFM (0.4 in. w.g.)
CONTROLS
This unit is very simple to operate: once it is installed, press
on its push button, located on the bottom of the unit, to
activate it. Press once for low speed, once again to high
speed, and once more to stop it.
•For more convenience, the following main controls are
available:
-Lite-Touch Constructo
no. 40370
-Simple-Touch Constructo
no. 40390
-Constructo
no. 40350
•Also, one to 5 of the following optional controls can be added:
-20-min. lighted push button
no. 12030
-60-min. mechanical timer
no. 00910
VB0072
AN INGENIOUS AIR EXCHANGE SOLUTION
THAT’S AS VERSATILE AS IT IS COMPACT!
Configured with factory built vertical or horizontal ports, the
AVS Constructo 1.0 HRV can fit almost anywhere. Hidden in a
bulkhead or in a closet, it is the most versatile 100-cfm unit
available on the market today. Among its exclusive features,
this unit is equipped with integrated balancing and backdraft
dampers in its exhaust to outside and fresh air supply ports.
For a standard installation, there is no need to balance the unit*,
thanks also to its twin high-pressure blowers. Its operation can
be interlocked with an existing furnace without adding an
extra relay. Also, for more convenience, its latches can be
relocated on its front (as shown on unit picture). This compact,
lightweight, and powerful unit is the ideal choice for small
pre-fab and tract houses, condos, apartments and other limited
space applications. What’s more, it is the only air exchanger
of its size that can be upgraded from an HRV to an ERV, simply
by changing its core.
*To avoid balancing, the difference between stale air ducts
total length and fresh air ducts total length must not exceed 50 ft.
•
•
•
•
•
20% smaller than comparable 100-cfm units
Versatile horizontal or vertical port configuration
Removable terminal block to ease optional wall control connections
Integrated pressure taps, if balancing required by building code
State-of-the-art ventilation technology
REPAIRS AND MAINTENANCE
All parts of the AVS Constructo 1.0 ERV that could need
maintenance can be removed in less than five minutes, allowing
direct access for easy repairs. The PSC motors are permanently
lubricated. Finally, the removable electrical drawer with pull-out
PCB assembly allows easy access for maintenance of major
sub-components.
WARRANTY
The AVS Constructo 1.0 HRV s protected by a 2-year warranty
on parts only. The energy recovery core is covered by a
lifetime warranty.
Available at:
OPTIONS
•Complete line of registers and diffusers
•Electric duct heater
•Dual exterior hood kit (including the Tandem® transition),
part no. 14690
HOMESHIELD™ DEFROSTING SYSTEM
The AVS Constructo 1.0 HRV uses a unique defrosting
method. No negative pressure is created by air exhausted to
the outside, as the air is recirculated into the house, thus
avoiding any backdraft from the chimney.
OUTSIDE
DEFROST CYCLE
TEMPERATURE defrosting min./
°C
(°F)
operating min.
STALE AIR
FROM
BULDING
Warmer
than -5
FILTERED
AIR TO
BUILDING
Warmer
than (23)
-5 TO -27 (23 TO -17)
-27 & LESS (-17 & LESS)
No
defrost
7/25
10/22
VF0036
HEAT RECOVERY CORE
Dimensions: 13” x 19” x 678” (33 cm x 48.3 cm x 17.3 cm)
Exchange surface: 55 ft² (5.1 m²)
Weight: 3.75 lb (1.7 kg)
Material: Polypropylene
Type: Crossflow core
Warranty: Limited Lifetime
REQUIREMENTS
AND
STANDARDS
•Complies with the UL 1812 requirements regulating the
installation of Heat Recovery Ventilators
•Complies with the CSA C22.2 no.113 Standard applicable
to ventilators
•Complies with CSA C444 requirements regulating the
installation of Energy Recovery Ventilators
•Technical data was obtained from published results of
tests relating to CSA C439 Standards
•HVI certified
DIMENSIONS
AND
SERVICE CLEARANCES: AVS CONSTRUCTO 1.0 HRV (PORTS
271 16” (688 mm)
229 16” (574 mm)
4” (102 mm)
ALL
PORTS FIT
ON SIDES)
1913 16” (503 mm)
5”
DIAMETER DUCTS
1
6” (152 mm)
13¾”
(349 mm)
2
12 3 16”
(310 mm)
3
4
2” (51 mm)
3. FRESH AIR FROM OUTSIDE PORT
4. EXHAUST AIR TO OUTSIDE PORT
1. FRESH AIR TO BUILDING PORT
2. EXHAUST AIR FROM BUILDING PORT
VK0055A
AVS CONSTRUCTO 1.0 HRV (PORTS
VENTILATION PERFORMANCE
EXT STATIC
PRESSURE
Pa in.w.g.
25
.1
50
.2
75
.3
100
.4
125
.5
150
.6
175
.7
200
.8
NET SUPPLY
AIR FLOW
l/s cfm m³/h
52 110 187
50 106 180
48 101 173
45
96 162
43
92 155
41
87 148
38
81 137
35
75 126
l/s
52
50
48
46
43
41
38
36
GROSS AIR FLOW
SUPPLY
EXHAUST
cfm m³/h l/s cfm m³/h
110 187 58 122 205
106 180 55 116 198
102 173 53 113 191
97 166 50 107 180
92 155 49 103 173
87 148 45
96 162
81 137 43
91 155
76 130 40
85 144
ALL
C°
F°
HEATING
0
+32
0
+32
0
+32
-25
-13
1
+95
NOTE: ALL
4’’ (102 mm)
1913 16”
(503 mm)
2
6’’ (152 mm)
3
2½”
(64 mm)
NET AIR FLOW
POWER SENSIBLE APPARENT LATENT RECOVERY/
CONSUMED RECOVERY SENSIBLE MOISTURE
3
m /h WATTS EFFICIENCY EFFECTIVENESS TRANSFER
l/s
cfm
23
30
44
48
63
93
82
108
157
68
82
116
66
65
59
78
76
68
0.07
0.04
0.04
30
63
108
110
55
81
0.08
-
-
-
TOTAL RECOVERY EFFICIENCY
NOT TESTED
16¼”
(413 mm)
VK0056A
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
SPECIFICATIONS
AND
Submitted by:
•Cabinet: 20 ga. pre-painted steel
•Insulation: expanded polystyrene
•Mounting: suspension by
chains and springs
•Supply & Exhaust Blower Motors: 2 motors
-Protection type: thermally protected
-Insulation class: B
Date:
Model no.:
12 3 16”
(310 mm)
1. FRESH AIR TO BUILDING PORT
2. EXHAUST AIR FROM BUILDING PORT
3. FRESH AIR FROM OUTSIDE PORT
4. EXHAUST AIR TO OUTSIDE PORT
RATINGS
•Model: Venmar AVS Constructo 1.0 HRV
•Part Number ports on top: 41502
•Part Number ports on sides: 41500
•Total Assembled Weight (including
polymerized paper core): 42 lb (19 kg)
•Oval shaped ports; fit 5” ducts
•Drains: 1/2” (1.2 cm) fittings with 10
ft (3 m) PVC drain
•Core filters: 30 ppi washable foam
-10.5” x 6.75” x 0.5” (26.7 x 17.2 x 1.3 cm)
Qty:
4
22 9 16” (574 mm)
23 ¾” (603 mm)
COOLING
+35
ON TOP)
5”
DIAMETER DUCTS
ENERGY PERFORMANCE
SUPPLY
TEMPERATURE
PORTS FIT
•Speed Control on unit: Low and High speed.
Other modes available with main and
optional wall controls.
•Energy Recovery Core:
-Heat Exchange Surface Area:
55 ft² (5.1 m²)
-Type/Material: Crossflow/Polypropylene
•Unit Electrical Characteristics:
Volts Frequence Amperes Watts
120
60 Hz
0.9
102
Project:
Location:
Remarks:
Architect:
Engineer:
Contractor:
Residential Product Group, 550 Lemire Blvd., Drummondville, QC, Canada J2C 7W9 - Tel.: 1-800-567-3855 Fax: 1-800-567-1715
R 2000
C
UL
www.venmar.ca
US
04/08
PRODUCT SHEET no. 91047
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement