Quick Reference Guide (Download PDF, 2.30M)

Quick Reference Guide (Download PDF, 2.30M)
2016 Infiniti Q70
1932611_16a_Q70_US_pQRG_092415.indd 2
Quick Reference Guide
9/24/15 11:06 AM
Behind 1
steering
wheel 2
6
4 Behind
3
7
5
8
7
11
10
21
steering
wheel
9
22
12
23
16
13 14 15
17 18
19
Behind
steering wheel
25
24
24
20
ADAPTIVE FRONT LIGHTING SYSTEM
1 (AFS) SWITCH*
14 BACK-UP COLLISION INTERVENTION (BCI)
SYSTEM OFF SWITCH
INSTRUMENT BRIGHTNESS
2 CONTROL SWITCHES*
15 WARNING SYSTEMS SWITCH
VEHICLE INFORMATION DISPLAY
3 4 TRIP RESET SWITCH*
5 TRIP COMPUTER SWITCHES
HEADLIGHT AND TURN SIGNAL SWITCH
6 PADDLE SHIFTERS*
7 LOW TIRE PRESSURE WARNING LIGHT
8 WIPER AND WASHER SWITCH
9 10 STEERING WHEEL SWITCHES
FOR AUDIO* / BLUETOOTH®
11 INTELLIGENT CRUISE CONTROL
16 TILT / TELESCOPIC STEERING WHEEL SWITCH*
17 REAR SUNSHADE SWITCH*
18 HEATED STEERING WHEEL SWITCH*
19 TRUNK LID RELEASE SWITCH
20 HOOD RELEASE*
21 CONTROL PANEL DISPLAY SCREEN
22 HEATER AND AIR CONDITIONER (automatic)
23 AUDIO SYSTEM
24 CLIMATE CONTROLLED SEAT SWITCH*
25 INFINITI DRIVE MODE SELECTOR
12 DYNAMIC DRIVER ASSISTANCE SWITCH*
13 VEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCH*
*See your Owner’s Manual for information.
1932611_16a_Q70_US_pQRG_092415.indd 3
9/24/15 11:06 AM
table of contents
new system features
Around View® Monitor with Moving Object Detection (MOD)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Automatic Anti-glare Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Blind Spot Warning (BSW) and Blind Spot Intervention® (BSI)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Back-up Collision Intervention (BCI) (if so equipped) . . . . . . . . . . . . . . . . . 4
Predictive Forward Collision Warning (PFCW) (if so equipped) . . . . . . . . . . 4
Forward Emergency Braking (FEB) (if so equipped) . . . . . . . . . . . . . . . . . . . 5
Lane Departure Warning (LDW) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . 5
essential information
Tire Pressure Monitoring System (TPMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Warning Systems Switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
INFINITI Drive Mode Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Accessing the Front Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Loose Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fuel-filler Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Clock Set/Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
first drive features
INFINITI Connection™ (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
INFINITI Intelligent Key System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Trunk Lid Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Front Power Seat Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Automatic Drive Positioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Outside Mirror Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Starting/Stopping the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Headlight Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Wiper and Washer Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Heater and Air Conditioner (automatic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
FM/AM/SiriusXM® Satellite Radio with CD/DVD (if so equipped) Player . 19
USB (Universal Serial Bus) Connection Port/iPod® Interface . . . . . . . . . . 20
Conventional (Fixed Speed) Cruise Control (if so equipped) . . . . . . . . . . . 20
Intelligent Cruise Control (ICC) (if so equipped) . . . . . . . . . . . . . . . . . . . . 21
system guide
Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Bluetooth® Hands-free Phone System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
System Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Bluetooth® System with Navigation (if so equipped) . . . . . . . . . . . . . . . . . 23
Bluetooth® System without Navigation (if so equipped) . . . . . . . . . . . . . . 25
Bluetooth® Streaming Audio (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 26
Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DVD Player (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
HomeLink® Universal Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Please see your Owner’s Manual for important safety information
and system operation limitations.
• A cellular telephone should not be used for any purpose while
driving so full attention may be given to vehicle operation.
• Always wear your seat belt.
• Supplemental air bags do not replace proper seat belt usage.
• Children 12 and under should always ride in the rear seat
properly secured in child restraints or seat belts according to
their age and weight.
• Do not drink and drive.
For more information, refer to the “Safety — Seats, seat belts and
supplemental restraint system (section 1)”, the “Monitor, climate, audio,
phone and voice recognition systems (section 4)” and the “Starting and
driving (section 5)” of your Owner’s Manual.
Additional information about your vehicle is also available in your Owner’s
Manual, Navigation System Owner’s Manual and at www.InfinitiUSA.com.
1932611_16a_Q70_US_pQRG_092415.indd 4
To view detailed
instructional videos, go to
www.infinitiownersinfo.mobi/2016/q70
or snap this barcode with an
appropriate barcode reader.
9/24/15 11:06 AM
new s y s te m f e a t u r e s
Around View® Monitor (AVM) with Moving Object Detection (MOD)
(if so equipped)
With the ignition switch in the ON position, the
Around View® Monitor is activated by pressing the
CAMERA button 1 , located on the control panel, or
by moving the shift lever to the R (REVERSE) position.
The control panel displays various views of the
position of the vehicle.
1
When the shift lever is in the P (PARK), N (NEUTRAL)
or D (DRIVE) position and the CAMERA button 1 is
pressed, the following views will display in order:
Start from any Control Panel screen
Front view and bird’s-eye view
Press
Press
Press
Front view and front-side view
Front wide view
Press
When the shift lever is in the R (REVERSE) position and the CAMERA button 1 is pressed,
the following views will display in order:
Rear view and bird’s-eye view
Rear view and front-side view
Press
Rear wide view
Press
Press
2
1932611_16a_Q70_US_pQRG_092415.indd 2
9/24/15 11:07 AM
The colored guide lines on the display screen indicate vehicle width and approximate
distances to objects with reference to the vehicle body line.
• Red 1.5 ft (0.5 m); Yellow 3 ft (1 m); Green 7 ft (2 m) and 10 ft (3 m).
There are some areas where the system will not show objects.
• When in the front or the rear view display, an
object below the bumper or on the ground may
not be viewed 2 .
•W
hen in the bird’s-eye view, a tall object near
the seam of the camera viewing areas 3
will not appear in the monitor.
2
The distance between objects viewed on the Around View®
Monitor (AVM) differs from the actual distance.
Objects in the bird’s-eye view will appear further
than the actual distance.
MOVING OBJECT DETECTION (MOD)
If the MOD system detects moving objects
surrounding the vehicle, a yellow frame 4 will
be displayed on the camera image and a chime
will sound.
3
5
6
4
In the bird’s-eye view, a yellow frame is displayed
on those camera images (front, rear, right, left)
where moving objects are detected.
7
When the following are displayed:
• Blue MOD icon 5 ; the system is operative in this view.
•G
ray MOD icon 6 ; the system is not operative in this view.
•N
o MOD icon; the system is off.
To temporarily turn the system on or off, touch the Sonar-MOD key 7 .
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your
Owner’s Manual.
Automatic Anti-glare Mirrors
The inside rearview mirror and both outside mirrors are designed to automatically change
reflection according to the intensity of the headlights of the vehicle following you.
The anti-glare system will be automatically turned on when the ignition switch is in the
ON position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
3
1932611_16a_Q70_US_pQRG_092415.indd 3
9/24/15 11:08 AM
new s y s te m f e a t u r e s
Blind Spot Warning (BSW) and Blind Spot Intervention® (BSI)
(if so equipped)
The BSW system alerts the driver when another
vehicle moves into the vehicle’s detection zone.
An indicator light located near the outside mirror 1
will illuminate if the radar sensors detect a vehicle
in the detection zone.
The BSI system can assist the driver in returning
the vehicle to the center of the traveling lane by
applying individual brake pressure to the left or right wheels for a short
period of time.
1
2
The indicator light 2 will first illuminate in orange and then turn green
before extinguishing. This indicates that the BSW and BSI systems
are operational.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Back-up Collision Intervention (BCI) (if so equipped)
The BCI system can help alert the driver of an approaching vehicle or objects behind the
vehicle when backing out of parking spaces.
The rear radar sensors detect the approaching vehicle from up to approximately
49 ft (15 m) from the bumper.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Predictive Forward Collision Warning (PFCW) (if so equipped)
The PFCW system can help alert the driver when there is sudden braking of the second
vehicle traveling in front of the vehicle ahead that is traveling in the same lane.
The PFCW uses a sensor in the front bumper to measure the distance of a second vehicle
ahead in the traveling lane. The system operates at speeds above 3 mph (5 km/h).
If there is a potential risk, the PFCW will warn the driver with a blinking driver assist system
forward indicator and an audible warning tone will be heard.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
4
1932611_16a_Q70_US_pQRG_092415.indd 4
9/24/15 11:08 AM
Forward Emergency Braking (FEB) (if so equipped)
The FEB system can assist the driver when there is a risk of a forward collision with the
vehicle in the traveling lane.
The FEB operates at speeds greater than 3 mph (5 km/h).
If there is a risk of a collision, an audible tone will be heard, a visual warning will display
and the vehicle will push up on the accelerator pedal. If the driver releases the accelerator
pedal, the vehicle will begin applying the brakes; however, if the driver does nothing, the
system will issue another audible and visual warning and apply the brakes harder.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Lane Departure Warning (LDW) (if so equipped)
The LDW system can help alert the driver when the vehicle is traveling too close to either
the left or the right side of a traveling lane.
The system will operate when the vehicle is driven at speeds of approximately 45 mph
(70 km/h) and above and only when the lane markings are clearly visible on the road.
When the vehicle approaches either the left or the right side of the traveling
lane, the LDW system will chime and the orange LDW light 1 on the
instrument panel will blink to alert the driver.
The LDW system can be turned on and off through
the Settings menu in the vehicle information
display. To temporarily turn off the system, push the
warning systems switch 2 .
1
2
3
When the system is off, the indicator light 3 on the
switch is off.
For more information, refer to the “Instruments and controls (section 2)” and the “Starting and driving (section 5)” of your
Owner’s Manual.
5
1932611_16a_Q70_US_pQRG_092415.indd 5
9/24/15 11:08 AM
essent i al i n f o r m a t i o n
Tire Pressure Monitoring System (TPMS)
A CHECK TIRE PRESSURE warning message will
appear in the vehicle information display 1 and
the low tire pressure warning light 2 will illuminate
when one or more tires are low in pressure and air
is needed.
1
• T he tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mi (1.6 km) at moderate speeds.
2
After the tire pressures are adjusted, drive the vehicle at speeds above 16 mph
(25 km/h). The CHECK TIRE PRESSURE warning message and low tire pressure warning
light 2 will extinguish.
When the low tire pressure warning light 2 flashes for 1 minute and then remains on, the
TPMS is not functioning properly. Have the system checked. It is recommended you visit
an INFINITI retailer for this service.
Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and
the outside temperature. Low outside temperature can lower the temperature of the air
inside the tire, which can cause a lower tire inflation pressure. This may cause the low tire
pressure warning light 2 to illuminate. If the warning light illuminates, check the tire
pressure in your tires.
•C
heck the tire pressure (including the spare tire) often and always prior to long
distance trips.
The Tire and Loading Information label contains valuable information. Please refer to the
“Technical and consumer information” (section 9) of your Owner’s Manual for the location
of the Tire and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
6
1932611_16a_Q70_US_pQRG_092415.indd 6
9/24/15 11:08 AM
Warning Systems Switch (if so equipped)
The warning systems switch 1 will turn on or off
any enabled warning systems including the Lane
Departure Warning and Blind Spot Warning systems.
Systems that are not enabled will always remain off.
When the warning systems switch 1 is turned off,
the indicator light 2 on the switch is off. If the
warning systems indicator light 2 is illuminated,
the system is on. The indicator will also be off if all
of the warning systems are deactivated using the
Settings menu.
1
2
3
4
6
To enable or disable these systems, perform the
following operation:
1. Press the SETTING button 3 on the control panel.
2. U
sing the INFINITI Controller 4 , highlight the
“Driver Assistance” key 5 on the display. Then
press the ENTER button 6 .
3. H
ighlight the corresponding warning system key
7 , select ON (enabled) or OFF (disabled) and
press the ENTER button 6 .
5
7
For more information, refer to the “Starting and driving (section 5)” of your
Owner’s Manual.
7
1932611_16a_Q70_US_pQRG_092415.indd 7
9/24/15 11:08 AM
essent i al i n f o r m a t i o n
INFINITI Drive Mode Selector
Turn the switch to one of the following positions to select the corresponding drive mode:
1 • (Standard) — Used for standard or normal driving.
1
2 SPORT — The engine and transmission will
adjust, resulting in higher engine rpm and a more
aggressive shift pattern. In this mode, fuel economy
may be reduced.
4
2
3
3 SNOW — Used on snowy roads or slippery areas. In
this mode, engine output is controlled to avoid wheel spin.
4 ECO — Adjusts engine and transmission points to enhance fuel economy.
ECO PEDAL SYSTEM (if so equipped)
With the INFINITI Drive Mode Selector switch in the ECO mode, the ECO pedal system
assists the driver in improving fuel economy.
The ECO pedal system applies force to make the accelerator pedal heavier, depending on
the accelerator pedal operation.
To change the ECO pedal reaction force:
1. Press the SETTING button on the control panel.
2. Touch the “ECO DRIVE” key.
3. Touch the “ECO pedal” key and select one of the options below:
• OFF — Turns the ECO pedal system off.
• Soft — Softens the reaction force.
• Standard — Reaction force is normal.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Accessing the Front Cup Holders
To open the cup holders, push the
lid 1 down and release.
For more information, refer to the “Instruments and
controls (section 2)” of your Owner’s Manual.
1
8
1932611_16a_Q70_US_pQRG_092415.indd 8
9/24/15 11:08 AM
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear in
the vehicle information display 1 when the
fuel-filler cap is not tightened correctly.
1
To tighten, turn the cap clockwise until a single click
is heard.
The warning message will extinguish when the
vehicle detects the fuel-filler cap is properly
tightened and the reset button 2 is pressed for
more than 1 second.
If the cap is not properly tightened, the Malfunction
Indicator Light
may illuminate.
2
For more information, refer to the “Instruments and controls (section 2)” and the
“Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Fuel-filler Door
The fuel-filler door is located on the passenger’s side of
the vehicle.
When the doors of the vehicle are locked or
unlocked, the fuel-filler door is automatically locked
or unlocked at the same time.
To open the door, push the upper left side of the door.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Clock Set/Adjustment
DIGITAL CLOCK ADJUSTMENT
To adjust the time and the appearance of the clock
on the display:
1. Press the SETTING button on the control panel.
2. Select the “Others” key.
3. Select the “Clock” key.
The following settings can be adjusted:
• On-screen Clock: The clock in the upper right corner of the display can be turned ON or OFF.
• Clock Format (24h): The clock can be set to 12 hours or 24 hours.
• Offset (hour): The time can be adjusted by increasing or decreasing per hour.
• Offset (min): The time can be adjusted by increasing or decreasing per minute.
• Daylight Savings Time: The application of Daylight Savings Time can be turned ON or OFF.
• Time Zone: Adjust the time zone. Choose a time zone from the available list.
Press the
BACK button to return to the previous screen.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your
Owner’s Manual.
9
1932611_16a_Q70_US_pQRG_092415.indd 9
9/24/15 11:08 AM
f i rst dr i v e f e a t u r e s
INFINITI Connection™* (if so equipped)
Infiniti Connection™ combines personalized convenience, concierge settings and personal
security features to compliment the Total Ownership Experience®. For more details on Infiniti
Connection or to enroll your vehicle, please visit www.InfinitiConnection.com or
call 855-444-7244.
To access Infiniti Connection™:
1
1. Press the INFO button 1 on the control panel.
2. Select the “Infiniti Connection” key 2 on the display.
Available services include:
Infiniti Personal Assistant — To access Infiniti
Personal Assistant, select “Connect to Voice Menu”
from the Infiniti Connection menu or touch the
key 3 on the map screen. At the voice prompt, say
“Infiniti Personal Assistant” to be connected.
2
Automatic Collision Notification – In case of air bag
deployment, a signal is sent containing the vehicle
location and customer information to notify the
proper authorities.
3
Emergency Call – This service provides emergency
assistance by connecting the subscriber to an
Infiniti Connection Specialist.
• In case of an emergency, press the in-vehicle
telematics SOS button 4 .
•A
Response Specialist will provide assistance
based on the situation described by the
vehicle’s occupant.
Enhanced Roadside Assistance – Roadside
Assistance can be accessed by touching the “Infiniti
Connection” key 2 on the Info menu or the
key 3 on the map screen.
4
• T his service allows subscribers to receive assistance for a non-emergency incident, such
as towing, or a third party response.
My Schedule – Access your personal online Google Calendar™, hear details read via
text-to-speech** and select a location as a destination via the Navigation System.
Report Stolen Vehicle – A Response Specialist will attempt to obtain location
information from a reported stolen vehicle and provide that information to a local law
enforcement agency.
Remote Door Lock/Unlock – Remotely access your vehicle via an Infiniti Connection
Response Specialist or the designated website to remotely lock or unlock your vehicle.
*INFINITI Connection™ is only available on vehicles equipped with an optional INFINITI Connection subscription service.
**Laws in some communities may restrict the use of text-to-speech. Check local regulations before using this feature.
10
1932611_16a_Q70_US_pQRG_092415.indd 10
9/24/15 11:08 AM
Alarm Notification – This system will notify you when the factory-installed vehicle alarm
system has been activated.
Scheduled Maintenance Notification – Receive scheduled maintenance notifications
based on mileage data provided by your vehicle.
Maintenance Alert – Receive notification of a vehicle system malfunction that triggers
instrument panel warning lights.
Destination Assistance – Receive point-of-interest assistance via a guided IVR (Interactive
Voice Response) or a Response Specialist by touching the
key 3 on the map screen or
the Infiniti Connection™ web portal.
Destination Send-to-Vehicle – Find and download point-of interest information from
Google Maps™ mapping service.
Connected Search – Select “Connected Search” from the Destination menu on the
vehicle’s Navigation System to conduct a point-of-interest search within a certain distance
of the vehicle’s location.
Drive Zone – Monitor the movement of your vehicle within a specified region. Set up
boundaries in the Monitoring section of the Infiniti Connection™ web portal.
Max Speed Alert – Set a maximum speed on the Infiniti Connection™ web portal. You will
receive notifications if your vehicle exceeds the maximum speed setting.
Mobile Information Service – Receive the latest news headlines, stock quotes and sports
scores by setting up preferences on the Mobile Information Service page in the Infiniti
Connection™ web portal.
Valet Alert – Use to set up a 0.2-mile radius around your vehicle.
• Activate alerts by touching the “Connect to Voice Menu” key on the Infiniti Connection
screen or by touching the
key 3 on the map screen.
•A
t the prompt, say “Valet Alert” and then “Activate” or “Deactivate”.
For more information, refer to the “Viewing technical information (section 7)” of your Navigation System Owner’s Manual.
11
1932611_16a_Q70_US_pQRG_092415.indd 11
9/24/15 11:08 AM
f i rst dr i v e f e a t u r e s
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to
lock or unlock your vehicle, open your trunk and
start the engine. It is important to make sure the
Intelligent Key is with you (that is, in your pocket
or purse).
1
LOCKING AND UNLOCKING YOUR VEHICLE
The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.
To lock the vehicle, push either door handle request switch 1
once or press the button 2 on the key fob.
2
To unlock the vehicle, perform one of the following procedures:
3
4
• Push either door handle request switch 1 once; the corresponding
door will unlock. Push the door handle request switch 1 again
within 1 minute; all other doors will unlock, or
•P
ress the
Press the
5
button 3 on the key fob to unlock the driver’s side door.
button 3 again; all other doors will unlock.
To open the trunk, press the
HOLD
button 4 for more than 1 second.
The Intelligent Key can also be used to activate the panic alarm by pressing and holding
the button 5 for more than 1 second. Once activated, the panic alarm and headlights
will stay on for a period of time.
INTELLIGENT KEY BATTERY DISCHARGE
If the battery of the Intelligent Key is discharged or
environmental conditions interfere with the
Intelligent Key operation, start the engine according
to the following procedure:
1. Move the shift lever to the P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key,
and a chime will sound.
4. Within 10 seconds after the chime sounds, push the ignition switch while depressing
the brake pedal and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the “Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
12
1932611_16a_Q70_US_pQRG_092415.indd 12
9/24/15 11:09 AM
Trunk Lid Release
Use one of the following methods to unlatch the trunk
lid then lift the lid to open the trunk:
Push the trunk open request switch 1 under the
trunk handle while carrying the INFINITI Intelligent
Key with you (that is, in your pocket
or purse).
1
Press the HOLD button 2 on the Intelligent Key for
more than 1 second.
2
From inside the vehicle, push the trunk lid
release switch 3 .
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
3
Front Power Seat Adjustments
To slide the seat forward or backward, push the
switch
1 forward or backward.
To recline the seatback, push the switch
forward or backward.
2
SEAT LIFTER
1
2
3
To adjust the angle of the front seat cushion or
height of the seat, push the front or rear end of the
switch
1 up or down.
LUMBAR SUPPORT
3 .
To adjust the seat lumbar support, push the front or back end of the switch
For more information, refer to the “Safety —Seats, seat belts and supplemental restraint system (section 1)” of your
Owner’s Manual.
13
1932611_16a_Q70_US_pQRG_092415.indd 13
9/24/15 11:09 AM
f i rst dr i v e f e a t u r e s
Automatic Drive Positioner
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner 1 memory.
1
Follow this procedure to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Push the ignition switch to the ON position.
• Adjust the driver’s seat, steering column and outside mirrors to the desired positions
using the adjusting switches for each feature.
• Push the SET switch, and within 5 seconds, push the memory switch (1 or 2) for at least
1 second.
• The indicator light on the memory switch you select will illuminate for approximately
5 seconds.
• The driver’s seat, steering column and outside mirror positions are now set to
your preferences.
These memorized positions can also be linked to your INFINITI Intelligent Key.
• To link a memorized position to your INFINITI Intelligent Key, press the unlock button on
the key fob after completing the previous step.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the
control switch 1 right or left.
3
2
Adjust each mirror to the desired position using
the switch 2 .
1
To fold the outside rearview mirrors, push the
switch 3 to the
position. To unfold the outside
rearview mirrors, push the switch 3 to the
position.
REVERSE TILT-DOWN FEATURE
When backing up the vehicle, the right or left outside mirror can be selected to
automatically turn downward.
1. Push the ignition switch to the ON position.
2. Move the shift lever to the R (REVERSE) position.
3. Choose the right or left outside mirror by operating the outside mirror control switch 1 .
4. The outside mirror surface moves downward.
When one of the following conditions has occurred, the outside mirror surface will return to
its original position.
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center or neutral position.
• The ignition switch is pushed to the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
14
1932611_16a_Q70_US_pQRG_092415.indd 14
9/24/15 11:09 AM
Starting/Stopping the Engine
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).
Depress the brake pedal.
Press the ignition switch START/STOP button to
start the engine.
TURNING THE ENGINE OFF
Move the shift lever to the P (PARK) position and
apply the parking brake.
Press the ignition switch START/STOP button to turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Headlight Control Switch
HEADLIGHT CONTROL
Turn the headlight control switch to the
position 1 to turn on the front parking, side
marker, tail, license plate and instrument panel
lights. Turn the switch to the
position 2 to turn
on the headlights.
3
1
2
AUTOLIGHT SYSTEM
The autolight system will automatically turn the headlights on when it is dark or when the
front wipers are used continuously. The autolight system will automatically turn off when
it is light and the wipers are not in continuous use. The system will keep the headlights on
for a period of time after you turn the ignition off and all doors are closed.
To activate the autolight system, turn the headlight control switch to the AUTO position 3
then push the ignition switch to the ON position. To deactivate the autolight system, turn
the headlight control switch to the OFF,
position 1 or
position 2 .
HIGH BEAM SELECT
With the headlights ON (either in the AUTO or
position), push the headlight control switch forward
4 to select the high beam function. The blue
indicator light
illuminates in the instrument
panel. Pull the headlight switch back to the original
position to select the low beam. The blue indicator
light extinguishes.
4
5
Pull and release the headlight control switch 5 to
flash the headlight high beams on and off.
15
1932611_16a_Q70_US_pQRG_092415.indd 15
9/24/15 11:09 AM
f i rst dr i v e f e a t u r e s
FOG LIGHT SWITCH
The headlights must be on and the low beams
selected for the fog lights to operate.
Turn the switch (inside collar) to the
to turn the fog lights on.
position 6
6
Turn the switch (inside collar) to the OFF position to
turn the fog lights off.
LANE CHANGE SIGNAL
Move the lever up or down until the turn signal begins to flash, but the lever does not
latch, to signal a lane change. Hold the lever until the lane change is completed.
Move the lever up or down until the turn signal begins to flash, but the lever does not
latch, and release the lever. The turn signal will automatically flash three times.
Choose the appropriate method to signal a lane change based on road and traffic conditions.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Wiper and Washer Switch
Move the lever to one of the following positions to
operate the windshield wipers:
3
MIST
1 Mist (MIST) - One sweep operation of the wipers.
OFF
2 Auto (AUTO) - Operates the rain-sensing wipers
AUTO 2
LO 4
intermittently. To increase or decrease wiper
sensitivity, twist the control ring 3 .
1
HI
5
4 Low (LO) - Wipers operate at a continuous
low-speed.
5 High (HI) - Wipers operate at a continuous
6 Pull the lever toward you to activate the washer.
high-speed.
6
The wipers will operate several times.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position in order to replace the wiper blades. To
move the wiper blades to the service position, follow this procedure:
When the ignition switch is in the ON position, lift the windshield wiper and washer lever
up to the MIST position 1 two times in less than 0.5 seconds. The windshield wipers will
move to the service position automatically, and the wiper blades can now be replaced.
To move the wiper blades back to the original position:
Lift the windshield wiper and washer lever up for more than 1 second or push the lever
down to operate at any wiper speed.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
16
1932611_16a_Q70_US_pQRG_092415.indd 16
9/24/15 11:09 AM
8
9
12
7
1
10
2
11
3
5
4
6
Heater and Air Conditioner (automatic)
1 AUTO BUTTON
The automatic mode may be used year-round. Press the AUTO button to turn the system
on, and the system will automatically control the inside temperature (automatic cooling
and/or dehumidified heating), air flow distribution and fan speed.
2 CLIMATE BUTTON
Press the CLIMATE button to adjust the automatic climate controls using the climate
settings on the control panel display screen.
3 DRIVER’S SIDE TEMPERATURE CONTROL BUTTONS
Press the driver’s side temperature control buttons up
cooler air.
for warmer air or down
for
4 DRIVER’S SIDE MANUAL AIR FLOW CONTROL BUTTON
Press the driver’s side manual air flow button to manually control the driver’s side air
flow modes.
The following air flow indicator modes will display on the control panel display screen:
Air flows from the center and side vents.
Air flows from the center, side and foot vents.
Air flows mainly from the foot vents.
Air flows from the front defroster and foot vents.
5 PASSENGER’S SIDE TEMPERATURE CONTROL BUTTONS
To manually adjust the passenger’s side temperature, press the passenger’s side
temperature control buttons up for warmer air or down for cooler air.
6 PASSENGER’S SIDE MANUAL AIR FLOW CONTROL BUTTON
Press the passenger’s side manual air flow button to manually control the passenger’s
side air flow modes.
The following air flow indicator modes will display on the control panel display screen:
Air flows from the center and side vents.
Air flows from the center, side and foot vents.
Air flows mainly from the foot vents.
Air flows from the front defroster and foot vents.
1932611_16a_Q70_US_pQRG_092415.indd 17
17
9/24/15 11:09 AM
f i rst dr i v e f e a t u r e s
7 FAN SPEED CONTROL BUTTONS
Press the left button to decrease the fan speed or press the right
increase the fan speed.
button to
8 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the front defroster button
to turn the system on. The A/C automatically
turns on when the front defroster mode is selected. This feature removes humidity from
the air.
To defrost the front and side windows, set the temperature controls 3 and fan speed
controls 7 to their maximum settings.
9 DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS
Push the rear window defroster switch
to turn the system on or off.
This function automatically turns off after approximately 15 minutes.
10 OUTSIDE AIR CIRCULATION BUTTON
Press the outside air circulation “
” button to change the air circulation mode. When
the indicator light illuminates, the flowing air is drawn from outside the vehicle.
11 AIR RECIRCULATION BUTTON
Press the air recirculation “
” button to change the air circulation mode. When the
indicator light illuminates, the flowing air is recirculated inside the vehicle.
The air recirculation mode cannot be activated when the climate control system is in the
front defroster mode
or front defroster and foot vent mode .
12 OFF BUTTON
Press the OFF button to turn the climate control system off.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your
Owner’s Manual.
18
1932611_16a_Q70_US_pQRG_092415.indd 18
9/24/15 11:09 AM
1
2
3
5
6
4
FM/AM/SiriusXM®* Satellite Radio with CD/DVD (if so equipped) Player
1 ON•OFF BUTTON/VOL (volume) CONTROL KNOB
Press the ON•OFF button to turn the system on or off.
Turn the VOL (volume) control knob right or left to increase or decrease the volume.
2 AUDIO BUTTON/TUNE/FOLDER KNOB
To manually tune the radio, turn the TUNE/FOLDER knob left or right.
Press the AUDIO button to access the audio settings screen.
3 SEEK•CAT/TRACK BUTTON
To scan quickly and stop at the previous or next broadcast station, press the
end of the SEEK•CAT/TRACK button.
For satellite radio, press the
or
end of the SEEK•CAT/TRACK button to switch to
the first channel of the previous or next category.
To change tracks on a CD, press the
To rewind or fast forward a track on a CD, press and hold the
SEEK•CAT/TRACK button.
or
or
end of the SEEK•CAT/TRACK button.
or
end of the
4 STATION PRESET BUTTONS
Twelve stations can be set for the FM band, six for the AM band and 18 for
satellite radio.
To store a station in a preset, you must first select a radio band by pressing the FM•AM
button 5 or XM button 6 then tune to the desired FM, AM or satellite radio station.
Next press and hold the desired station preset button (1-6) until the preset number is
updated on the display and the sound is briefly muted. The channel indicator will then
display, and the sound will resume. Programing is now complete.
To retrieve a previously set station, select the radio band where the preset was stored
then press the corresponding station select button (1-6).
*SiriusXM® Satellite Radio is only available on vehicles equipped with an optional satellite radio subscription service.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your
Owner’s Manual.
19
1932611_16a_Q70_US_pQRG_092415.indd 19
9/24/15 11:09 AM
f i rst dr i v e f e a t u r e s
USB (Universal Serial Bus) Connection Port/iPod® Interface
The USB port 1 is located in the center console
under the armrest.
When a compatible USB memory device or iPod®
is plugged into the USB port, compatible audio
and video files stored on the device can be
played through the vehicle’s audio system and front
display.
1
For more information, refer to the “Monitor, climate, audio, phone
and voice recognition systems (section 4)” of your Owner’s Manual.
Conventional (Fixed Speed) Cruise Control (if so equipped)
The cruise control system enables you to set a
constant cruising speed once the vehicle has reached
25 mph (40 km/h).
The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.
4
3
1
2
To activate the cruise control, push the ON/OFF
switch 1 . The CRUISE indicator light in the
instrument panel will illuminate.
To set a cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET
switch 2 and release. The SET indicator light in the instrument panel will illuminate. Take
your foot off the accelerator pedal. Your vehicle will maintain the set speed.
To reset at a faster cruising speed, push and hold the ACCEL/RES switch 3 . When the
vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the COAST/SET switch 2 . Release the
switch when the vehicle slows to the desired speed.
To cancel the preset speed, push the CANCEL switch 4 .
To turn off cruise control, push the ON/OFF switch 1 . Both the CRUISE indicator light and
the SET indicator light in the instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
20
1932611_16a_Q70_US_pQRG_092415.indd 20
9/24/15 11:09 AM
Intelligent Cruise Control (ICC) (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button 1 for less
than 1.5 seconds. The CRUISE indicator light 2
will illuminate.
8
7
4
3
Accelerate to the desired speed.
Push down on the COAST/SET switch 3 and release
it. Intelligent Cruise Control will be set to the
desired speed.
1
Press the distance button 4 repeatedly to change
the set distance between long, middle and short.
When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed
indicator lights will illuminate 5 in set mode.
2
5
When a vehicle is detected ahead of you in the lane, the vehicle ahead
detection, set distance and set vehicle speed indicator lights will
illuminate 6 in set mode.
6
To reset at a faster cruising speed, push and hold the ACCEL/RES switch 7 . When the
vehicle attains the desired speed, release the switch.
To reset at a slower cruising speed, push and hold the COAST/SET switch 3 . Release the
switch when the vehicle slows to the desired speed.
To cancel the preset speed, push the CANCEL switch 8 or tap the brake pedal. The set
vehicle speed indicator 5 will extinguish.
To turn off Intelligent Cruise Control, press the CRUISE ON/OFF button 1 . The CRUISE
indicator light 2 in the instrument panel will extinguish.
To set conventional (fixed speed) cruise control mode:
When ICC is off, press the CRUISE ON/OFF button 1 and hold it down for more than 1.5
seconds. The CRUISE indicator light will illuminate.
Accelerate to the desired speed.
Push down on the COAST/SET switch 3 and release it. The SET indicator light will
illuminate. Cruise control should be set to the desired speed.
To switch between the two cruise control modes:
When one of the two cruise modes is in use, you must turn the system off and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
21
1932611_16a_Q70_US_pQRG_092415.indd 21
9/24/15 11:09 AM
syste m g ui d e
Trip Computer
When the
button 1 is pressed, the following
modes will appear on the vehicle information
display 2 :
• MPG – Displays the current fuel consumption.
• M
PG/MPH – Displays the average fuel
consumption and speed since the last reset.
— T o reset the displayed MPG/MPH, press and
hold the
button 3 for more than 1 second.
Both the displayed MPG/MPH will reset at the
same time.
1
3
2
• T IME/MILES – Displays the elapsed time and
total distance the vehicle has been driven since
the last reset.
— T o reset the elapsed time/miles, press and hold the
button 3 for more than 1
second. Both the elapsed time/miles will reset at the same time.
•R
ANGE – Displays the estimated distance to empty (dte) the vehicle can be driven
before refueling.
•O
UTSIDE TEMP – Displays the exterior air temperature, including a low temperature
warning feature.
•S
ETTING – Allows you to set reminders for alerts and maintenance intervals or change
the language and units used in the system.
— Press the
— Press the
button 3 to cycle through the various setting modes.
button 1 to choose the selected menu.
• T o reset Trip A and Trip B, press and hold the TRIP RESET button for more than 1 second.
• WARNING – Displays when a warning is present.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
Bluetooth® Hands-free Phone System
A cellular telephone should not be used while
driving so full attention may be given to
vehicle operation.*
SYSTEM OPERATING TIPS
Bluetooth®
Controls
If the Voice Recognition system does not recognize
your voice commands:
1. Be sure to wait for the tone/beep before speaking
a command.
2. Reduce background noise as much as possible by
closing the windows and the moonroof.
3. Make sure there are no other conversations on
going in the car at the same time.
4. Lower HVAC blower fan speed and point vents
away from the ceiling microphone.
5. Speak naturally. Speaking too fast, too slow, too soft or too loud
makes voice recognition more difficult.
Microphone
*Some jurisdictions prohibit the use of cellular telephones while driving.
22
1932611_16a_Q70_US_pQRG_092415.indd 22
9/24/15 11:09 AM
6. C
onfirm the correct voice commands are being used. Glance at the screen to see the
currently available commands.
7. T rain the system using the Speaker Adaptation Mode. See your Owner’s Manual for
detailed information.
or button on the steering wheel to interrupt the voice prompts at any time
Press the
and speak a command after the tone.
For vehicles not equipped with Navigation:
• To use the system faster, you may speak the second level commands with the main
or button on the
menu command on the main menu. For example, press the
steering wheel, and after the tone, say “Call Redial”.
For vehicles equipped with Navigation:
• Refer to the “Voice recognition (section 9)” of your Navigation System Owner’s Manual
for more information.
The “Help” command can be used to hear a list of available commands at any time.
When speaking phonebook names, please be aware some cellular phones require the last
name to be spoken before the first name. For example, “Michael Smith” may be spoken as
“Smith Michael”.
To cancel a Voice Recognition session, say “Cancel” or “Quit” or press and hold the
button on the steering wheel for 5 seconds.
or
To go back to the previous command, say “Go Back” or “Correction”.
For more detailed information and instructions, refer to your cellular phone’s Owner’s
Manual and visit www.InfinitiUSA.com/bluetooth.
Bluetooth® System with Navigation*
(if so equipped)
CONNECTING PROCEDURE
The vehicle must be stationary when connecting the
cellular phone.*
1.Press the button and select the
“Connect Phone” key.
2. Initiate connecting from the cellular phone.
• T he connecting procedure varies according
to each cellular phone model. For detailed
connecting instructions and a list of
compatible cellular phones, please visit
www.InfinitiUSA.com/bluetooth.
•W
hen prompted for a PIN, enter “1234”
from the handset. (The PIN is assigned
by INFINITI and cannot be changed.)
• F or cellular phones that support SSP (Simple
Secure Pairing), confirm the PIN on the vehicle
display matches the PIN displayed on the
cellular phone.
3.When connecting is complete, the screen will return
to the Phone menu.
*Some jurisdictions prohibit the use of cellular telephones while driving.
1932611_16a_Q70_US_pQRG_092415.indd 23
23
9/24/15 11:10 AM
syste m g ui d e
Some phones may require you to accept certain
permissions in order to enable features on your
Bluetooth® system. During the Bluetooth® pairing
process, please check your phone’s display for a
pop-up with the request to grant phonebook access.
Granting phonebook access permission will allow
your contacts to be downloaded to the vehicle
Bluetooth® system. A pop-up may display on your
phone stating that the Bluetooth® system would
like to access your contacts and call history. Please select “Allow” or “Yes” to grant this
permission. If your phone presents the option to not show the message again, please
make sure that this item is checked. Doing so will ensure that any changes to your
phonebook will be synced with the Bluetooth® system automatically.
PHONEBOOK SETUP
Depending on your cellular phone, the system may
automatically download your cellular phone’s entire
phonebook to the vehicle’s Bluetooth® system.
If the phonebook does not download
automatically, the vehicle’s phonebook may be
set for up to 40 entries.
To manually download entries:
1.Press the button on the steering wheel and
select the “Quick Dial” key.
2.Select the “Add New” key at the top of the display.
There are different methods to input a phone
number. Select one of the following options:
• “Copy from Call History”- to save a number from the Outgoing, Incoming or
Missed Calls lists.
• “ Copy from the Phonebook”- to save a number that has been downloaded from your
handset to the vehicle.
• “ Enter Number by Keypad”- to input the number and name manually.
MAKING A CALL
To make a call, follow this procedure:
1.Press the button. The “Phone” menu will appear
on the control panel display.
2.Select the “Quick Dial”, “Call History”,
“Phonebook”or “Dial Number” key.
3. Select the desired entry from the list.
4. Select “Call” to start dialing the number.
24
1932611_16a_Q70_US_pQRG_092415.indd 24
9/24/15 11:10 AM
RECEIVING/ENDING A CALL
To accept the call, press the button on the
steering wheel or touch the “Answer” key.
To reject the call, touch the “Reject Call” key.
To hang-up, press the button on the steering
wheel or touch the “Hang up” key.
Bluetooth® System without Navigation* (if so equipped)
PAIRING PROCEDURE
1.Press the
button on the steering wheel. The
system announces the available commands.
2. Say: “Connect Phone”. The system acknowledges
the command and announces the next set of
available commands.
3.Say: “Add Phone”. The system acknowledges the
command and asks you to initiate connecting
from the cellular phone handset.
4. Initiate pairing from the cellular phone.
• T he connecting procedure varies according to each cellular phone model.
For detailed connecting instructions and a list of compatible cellular phones, please
visit www.InfinitiUSA.com/bluetooth.
•W
hen prompted for a PIN, enter “1234” from the handset. (The PIN is assigned by
INFINITI and cannot be changed.)
5.Say a name for the cellular phone when the system asks to provide one. You can give the
cellular phone a name of your choice.
PHONEBOOK REGISTRATION
When the cellular phone is connected to the in-vehicle module, the data stored in the
cellular phone, such as the phonebook, outgoing call logs, incoming call logs and missed
call logs, is automatically transferred and registered to the system.
The availability of this function depends on each cellular phone. The copying procedure
also varies according to each cellular phone. See your cellular phone’s Owner’s Manual for
more information.
Up to 1,000 entries per registered cellular phone can be stored in the phonebook.
MAKING A CALL
1. Push the
button on the steering wheel. A tone will sound.
2.Say: “Call”. The system acknowledges the command and announces the next set of
available commands.
1932611_16a_Q70_US_pQRG_092415.indd 25
25
9/24/15 11:10 AM
syste m g ui d e
3.Say the registered person’s name. The system acknowledges the command and
announces the next set of available commands.
4.Say: “Yes”. The system acknowledges the command and makes the call.
RECEIVING/ENDING A CALL
To accept the call, press the
To reject the call, press the
To hang-up, press the
button on the steering wheel.
button on the steering wheel.
button on the steering wheel.
*Some jurisdictions prohibit the use of cellular telephones while driving.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your Owner’s
Manual or visit www.InfinitiUSA.com/bluetooth.
Bluetooth® Streaming Audio with Navigation (if so equipped)
If you have a compatible Bluetooth® device with streaming audio (A2DP and AVRCP
profiles), you can set up the wireless connection between your Bluetooth® device and your
vehicle’s audio system. This connection allows you to listen to audio from the Bluetooth®
device using your vehicle’s speakers.
A cellular telephone should not be used while driving so full attention may be given to
vehicle operation.*
To use your connected Bluetooth® device to
stream audio, it will need to be connected as an
audio device. The following procedure will initially
connect a Bluetooth® device as an audio player and
allow you to switch between devices.
1.Press the SETTING button on the control panel
and touch the “Bluetooth” key on the display.
2.Select “Connected Devices”.
3.Select “Audio Player”.
4. S
elect the name of the device that you are
attempting to connect as an audio player.
5.Select “Select”.
6. Verify that the system confirms that the device
has been selected as an audio player.
Once your Bluetooth® device has been connected
as an audio device, press the DISC•AUX button on
the control panel to select the Bluetooth® Streaming
Audio player.
Bluetooth® connectivity issues can usually be
resolved with a reboot of your cellular phone if you
do not regularly turn off your cellular phone. Otherwise, try updating your cellular phone
with the latest software.
*Some jurisdictions prohibit the use of cellular telephones while driving.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your Owner’s
Manual or visit www.InfinitiUSA.com/bluetooth.
26
1932611_16a_Q70_US_pQRG_092415.indd 26
9/24/15 11:10 AM
8
10
5
2
4
1
3
7
6
17
Navigation System (if so equipped)
Your Navigation System can calculate a route from your current location to a preferred
destination. The real-time map display and turn-by-turn voice guidance will lead you along
the route.
The Navigation System will continually update your vehicle’s position. If you have deviated
from the original route, it will recalculate the route from your current location.
SYSTEM OPERATION
Move through the menus and on-screen keys by sliding or rotating the INFINITI controller
1 to highlight an item on the screen and pressing the ENTER button 2 to select the
highlighted item, or by touching the desired key on the touch-screen display.
Press the
BACK button 3 to return to the previous screen. In a settings screen, this
button can also be used to apply the setting. In a character input screen, this button can also
delete the characters that have been entered.
Press the MAP button 4 to display the map. While following a programed route, press
multiple times to change the type of route information.
To display the vehicle, traffic (if so equipped), weather (if so equipped) or Voice Recognition
information, press the INFO (information) button 5 .
Press the
OFF button 6 to switch between the day screen (bright) and the night
screen (dark). Press and hold the button to turn the display off. Press again to turn the
display on.
To display system settings, press the SETTING button 7 .
1932611_16a_Q70_US_pQRG_092415.indd 27
27
9/24/15 11:10 AM
syste m g ui d e
SETTING A ROUTE
To set a route, first ensure that the correct region is selected on the touch-screen.
1. Press the DEST button 8 on the control panel.
2. Select the “Change Region” key 9 .
3. Select the preferred region.
9
Once this is complete, select your destination:
1. Press the DEST button 8 on the control panel.
2. Select the preferred destination setting method.
3.Enter the address number, street name, and city
as prompted by the screen.
CANCELLING A ROUTE
1. Press the ROUTE button 10 on the control panel.
11
2. Select the “Cancel Route” key 11 .
ZOOMING IN AND OUT
On the map screen, turn the INFINITI controller 1
right or left to zoom in or out.
MOVING AROUND THE MAP
To scroll the map, slide the INFINITI controller 1 in the direction you want to scroll.
CHANGING THE MAP VIEW
It is possible to switch between two different map views: 2D and bird’s eye view (3D).
To switch to the preferred map view:
1.With the map displayed, press the ENTER
button 2 on the control panel.
12
2.Select the “Change View” key 12 to change the
view to 2D or bird’s eye view (3D).
13
3.Select the “Map Settings” key 13 to change the
orientation of the map.
VOICE GUIDANCE
To activate voice guidance:
1. Press the ROUTE button 10 on the control panel.
2.Select the “Guidance Settings” key 14 .
3.To ensure that voice guidance is activated, select
the “Guidance Voice” key 15 . The indicator
illuminates if voice guidance is activated.
To adjust the guidance volume, select the
“Guidance Volume” key 16 .
14
16
15
To hear the current guidance during a programed
route, press the VOICE button 17 .
For more information, refer to your Navigation System Owner’s Manual.
28
1932611_16a_Q70_US_pQRG_092415.indd 28
9/24/15 11:11 AM
DVD Player (if so equipped)
This system allows you to play video files via a DVD
or CD from the front display.
To view movies on the front display, stop the
vehicle in a safe location, move the shift lever to the
P (PARK) position and apply the parking brake.
To reduce driver distraction, movies will not be
shown on the front display while the vehicle is in
any drive position.
For more information, refer to the “Monitor, climate, audio, phone and voice
recognition systems (section 4)” of your Owner’s Manual.
HomeLink® Universal Transceiver
The HomeLink® Universal
Transceiver can learn and
consolidate the functions of
up to three different hand-held
transmitters, operating items
such as garage doors, property
gates, outdoor and indoor lights
or alarm systems.
HOMELINK
To program the HomeLink Universal Transceiver:
• Position the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink surface,
keeping the HomeLink indicator light in view.
• Press and hold the desired HomeLink button and the handheld transmitter button
simultaneously until the HomeLink indicator light flashes slowly and then rapidly.
• Both buttons may be released when the indicator light flashes rapidly.
To verify the programing is complete, press and hold the HomeLink button and observe the
indicator light:
• A solid, continuous light indicates the programing is complete, and the HomeLink button
will activate your device.
• A blinking light that turns to a solid, continuous light after 2 seconds indicates additional
steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete the
programing process:
• At the receiver of the device that you are programing to the HomeLink button, press
and release the learn or smart button (the name may vary by manufacturer, but it is
usually located near where the hanging antenna wire is attached to the unit). You have
approximately 30 seconds to initiate the following step.
• Press and hold the programed HomeLink button for 2 seconds and release.
You may have to repeat the previous two steps up to three times to complete the
programing process. HomeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website
at www.homelink.com or call 1-800-355-3515.
1932611_16a_Q70_US_pQRG_092415.indd 29
29
9/24/15 11:11 AM
Helpful Resources
Below is a list of helpful resources that can be used to learn more about the vehicle’s systems
and feature operations.
Printing: October 2015 (07) / QR16EA 0Y51U0 / Printed in USA
• Vehicle Owner’s Manual
•Infiniti Client Support
1-800-662-6200
Support is always available if your Infiniti retailer
cannot assist you or you would like to provide
Infiniti directly with comments or questions.
•Infiniti Roadside Assistance
1-800-662-6200 (option 1)
As part of the Infiniti Total Ownership
Experience®, Roadside Assistance is available
to you, 24 hours a day 365 days a year,
for emergency roadside assistance.
•Infiniti Elite® Extended Protection Program
1-800-662-6200
Infiniti Elite® Assurance Products provide
you with quality long-term protection
and enhanced peace of mind.
•Infiniti Personal Assistant
1-888-774-1411
www.infinitipersonalassistant.com
Infiniti Personal Assistant™ provides Infiniti
owners 24-hour access to an entire team of
professional live personal assistants.
•Infiniti Financial Services Client Support
1-800-627-4437
For client support with your Infiniti
Financial Services loan or lease.
•Infiniti Financial Services
www.infinitifinance.com
Use the IFS Online Account Manager to check
your account status, schedule recurring
payments and access important forms.
•Owner Portal
1-855-444-7244
www.owners.InfinitiUSA.com/iowners
Your Infiniti Owner Portal account contains your
personal preferences, vehicle information and
links to key vehicle features and services.
•Infiniti Connection™
1-800-334-7858
www.InfinitiUSA.com/intouch/connection
The suite of digital alerts and remote services is
your direct link to personal security,
convenience and confidence.
•SiriusXM
1-888-601-6296
For support with your SiriusXM subscription.
•Infiniti USA.com
www.InfinitiUSA.com/bluetooth
Reference this site for a list of compatible
cellular phones and instructions on how to
pair your cellular phone to your vehicle.
•Infiniti Electronic Quick Reference Guide
(use Quick Response (QR) code or URL below)
To view detailed instructional videos,
go to www.infinitiownersinfo.mobi/2016/q70
or snap this barcode with an appropriate
barcode reader.
This Quick Reference Guide is intended to provide an overview of some of the unique features of your new vehicle.
Please see your Owner’s Manual for important safety information and system operation limitations. Features and
equipment in your vehicle may vary depending on model, trim level, options selected, order, date of production,
region or availability. Therefore, you may find information about features or equipment that are not included or
installed on your vehicle.
All information, specifications and illustrations in this Quick Reference Guide are those in effect at the time
of printing. INFINITI reserves the right to change specifications, performance, design or component suppliers
without notice and without obligation. From time to time, INFINITI may update or revise this Quick Reference
Guide to provide owners with the most accurate information currently available. Please carefully read and retain, with
this Quick Reference Guide, all revision updates sent to you by INFINITI to ensure you have access to
accurate and up-to-date information regarding your vehicle. Current versions of vehicle Quick Reference
Guides, Owner’s Manuals and any updates can also be found in the Owner section of the INFINITI website at
https://owners.infinitiusa.com/iowners/navigation/manualsAndGuides. If you have questions concerning any
information in your Owner’s Manual, contact INFINITI Client Support (see contact information listed above).
1932611_16a_Q70_US_pQRG_092415.indd 1
9/24/15 11:06 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement