A-Gas R407F

A-Gas R407F
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 1 of 10
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME
A-Gas R407F
PROPER SHIPPING NAME
LIQUEFIED GAS, N.O.S.(contains tetrafluoroethane,difluoromethane and pentafluoroethane)
PRODUCT USE
The use of a quantity of material in an unventilated or confined space may result in increased exposure and an irritating
atmosphere developing. Before starting consider control of exposure by mechanical ventilation.
Refrigerant.
SUPPLIER
Company: A- Gas (Australia) Pty Ltd
Address:
9- 11 Oxford Road
Laverton North
VIC 3026
Australia
Telephone: [ 61] (0) 3 93689222
Emergency Tel:TOLL: [ 61] 1800 024 973
Fax: [ 61] (0) 3 93689233
Section 2 - HAZARDS IDENTIFICATION
CHEMWATCH HAZARD RATINGS
Flammability
Toxicity
Body Contact
Reactivity
Chronic
SCALE:
Min/Nil=0
Low=1
Moderate=2
High=3
Extreme=4
GHS Classification
Gas under Pressure (Compressed gas)
STOT - SE (Narcosis) Category 3
STOT - SE (Resp. Irr.) Category 3
EMERGENCY OVERVIEW
HAZARD
WARNING
Determined by Chemwatch using GHS criteria
H280
Contains gas under pressure; may explode if heated.
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
H335
H336
AUH044
PRECAUTIONARY STATEMENTS
Prevention
Code
P261
P271
Response
Code
P304+P340
P312
Storage
Code
P403+P233
P405
P410+P403
Disposal
Code
P501
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 2 of 10
Section 2 - HAZARDS IDENTIFICATION
May cause respiratory irritation.
May cause drowsiness or dizziness.
Risk of explosion if heated under confinement
Phrase
Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray.
Use only outdoors or in a well- ventilated area.
Phrase
IF INHALED: Remove victim to fresh air and keep at rest in a position
comfortable for breathing.
Call a POISON CENTER or doctor/physician if you feel unwell.
Phrase
Store in a well- ventilated place. Keep container tightly closed.
Store locked up.
Protect from sunlight. Store in a well- ventilated place.
Phrase
Dispose of contents/container to ...
Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS
NAME
tetrafluoroethane
difluoromethane
pentafluoroethane
CAS RN
811-97-2
75-10-5
354-33-6
%
25-50
25-50
25-50
Section 4 - FIRST AID MEASURES
SWALLOWED
■ Not considered a normal route of entry.
If poisoning occurs, contact a doctor or Poisons Information Centre.
• Avoid giving milk or oils.
• Avoid giving alcohol.
• If spontaneous vomiting appears imminent or occurs, hold patient's head down, lower than their hips to help avoid possible
aspiration of vomitus.
EYE
• If product comes in contact with eyes remove the patient from gas source or contaminated area.
• Take the patient to the nearest eye wash, shower or other source of clean water.
• Open the eyelid(s) wide to allow the material to evaporate.
• Gently rinse the affected eye(s) with clean, cool water for at least 15 minutes. Have the patient lie or sit down and tilt the
head back. Hold the eyelid(s) open and pour water slowly over the eyeball(s) at the inner corners, letting the water run out of
the outer corners.
SKIN
■ If skin contact occurs:
• Immediately remove all contaminated clothing, including footwear.
• Flush skin and hair with running water (and soap if available).
• Seek medical attention in event of irritation.
INHALED
• Following exposure to gas, remove the patient from the gas source or contaminated area.
• NOTE: Personal Protective Equipment (PPE), including positive pressure self-contained breathing apparatus may be required to
assure the safety of the rescuer.
• Prostheses such as false teeth, which may block the airway, should be removed, where possible, prior to initiating first aid
procedures.
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 3 of 10
Section 4 - FIRST AID MEASURES
• If the patient is not breathing spontaneously, administer rescue breathing.
NOTES TO PHYSICIAN
for intoxication due to Freons/ Halons;
A: Emergency and Supportive Measures
• Maintain an open airway and assist ventilation if necessary
• Treat coma and arrhythmias if they occur. Avoid (adrenaline) epinephrine or other sympathomimetic amines that may precipitate
ventricular arrhythmias. Tachyarrhythmias caused by increased myocardial sensitisation may be treated with propranolol, 1-2 mg
IV or esmolol 25-100 microgm/kg/min IV.
• Monitor the ECG for 4-6 hours
B: Specific drugs and antidotes:
• There is no specific antidote.
For frost-bite caused by liquefied petroleum gas:
• If part has not thawed, place in warm water bath (41-46 C) for 15-20 minutes, until the skin turns pink or red.
• Analgesia may be necessary while thawing.
• If there has been a massive exposure, the general body temperature must be depressed, and the patient must be immediately
rewarmed by whole-body immersion, in a bath at the above temperature.
• Shock may occur during rewarming.
for gas exposures:
-------------------------------------------------------------BASIC TREATMENT
-------------------------------------------------------------• Establish a patent airway with suction where necessary.
• Watch for signs of respiratory insufficiency and assist ventilation as necessary.
• Administer oxygen by non-rebreather mask at 10 to 15 l/min.
• Monitor and treat, where necessary, for pulmonary oedema .
Vapourising liquid causes rapid cooling and contact may cause cold burns, frostbite, even through normal gloves. Frozen skin
tissues are painless and appear waxy and yellow.
Section 5 - FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA
■ SMALL FIRE: Use extinguishing agent suitable for type of surrounding fire.
LARGE FIRE: Cool cylinder.
DO NOT direct water at source of leak or venting safety devices as icing may occur.
FIRE FIGHTING
■ -------------------------------------------------------------GENERAL
-------------------------------------------------------------• Alert Fire Brigade and tell them location and nature of hazard.
• Wear breathing apparatus and protective gloves.
• Fight fire from a safe distance, with adequate cover.
• Use water delivered as a fine spray to control fire and cool adjacent area.
FIRE/EXPLOSION HAZARD
• Containers may explode when heated - Ruptured cylinders may rocket
• Fire exposed containers may vent contents through pressure relief devices.
• High concentrations of gas may cause asphyxiation without warning.
• May decompose explosively when heated or involved in fire.
Decomposition may produce toxic fumes of: carbon monoxide (CO), carbon dioxide (CO2), hydrogen fluoride, other pyrolysis products
typical of burning organic material.
Contains low boiling substance: Closed containers may rupture due to pressure buildup under fire conditions.
FIRE INCOMPATIBILITY
• Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition may
result.
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 4 of 10
Section 6 - ACCIDENTAL RELEASE MEASURES
MINOR SPILLS
• Avoid breathing vapour and any contact with liquid or gas. Protective equipment including respirator should be used.
• DO NOT enter confined spaces were gas may have accumulated.
• Increase ventilation.
• Clear area of personnel.
MAJOR SPILLS
• Clear area of all unprotected personnel and move upwind.
• Alert Emergency Authority and advise them of the location and nature of hazard.
• Wear breathing apparatus and protective gloves.
• Prevent by any means available, spillage from entering drains and water-courses.
• Remove leaking cylinders to a safe place.
• Fit vent pipes. Release pressure under safe, controlled conditions
• Burn issuing gas at vent pipes.
• DO NOT exert excessive pressure on valve; DO NOT attempt to operate damaged valve.
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
Section 7 - HANDLING AND STORAGE
PROCEDURE FOR HANDLING
• Consider use in closed pressurised systems, fitted with temperature, pressure and safety relief valves which are vented for
safe dispersal.
• The tubing network design connecting gas cylinders to the delivery system should include appropriate pressure indicators and
vacuum or suction lines.
• Fully-welded types of pressure gauges, where the bourdon tube sensing element is welded to the gauge body, are recommended.
• Before connecting gas cylinders, ensure manifold is mechanically secure and does not containing another gas. Before
disconnecting gas cylinder, isolate supply line segment proximal to cylinder, remove trapped gas in supply line with aid of
vacuum pump.
• DO NOT transfer gas from one cylinder to another.
SUITABLE CONTAINER
• DO NOT use aluminium or galvanised containers.
• Cylinder:
• Ensure the use of equipment rated for cylinder pressure.
• Ensure the use of compatible materials of construction.
• Valve protection cap to be in place until cylinder is secured, connected.
STORAGE INCOMPATIBILITY
As a general rule, hydrofluorocarbons tend to be flammable unless they contain more fluorine atoms than hydrogen atoms.
Haloalkanes:
• are highly reactive:some of the more lightly substituted lower members are highly flammable; the more highly substituted may be
used as fire suppressants, not always with the anticipated results.
• may react with the lighter divalent metals to produce more reactive compounds analogous to Grignard reagents.
• may produce explosive compounds following prolonged contact with metallic or other azides
• may react on contact with potassium or its alloys - although apparently stable on contact with a wide rage of halocarbons,
reaction products may be shock-sensitive and may explode with great violence on light impact; severity generally increases
with the degree of halocarbon substitution and potassium-sodium alloys give extremely sensitive mixtures .
• Compressed gases may contain a large amount of kinetic energy over and above that potentially available from the energy of
reaction produced by the gas in chemical reaction with other substances.
STORAGE REQUIREMENTS
• Cylinders should be stored in a purpose-built compound with good ventilation, preferably in the open.
• Such compounds should be sited and built in accordance with statutory requirements.
• The storage compound should be kept clear and access restricted to authorised personnel only.
• Cylinders stored in the open should be protected against rust and extremes of weather.
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 5 of 10
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE CONTROLS
Source
Material
__________
Australia
Exposure
Standards
__________
(1, 1, 1, 2Tetrafluoroethan
e)
The following materials had no OELs on our records
• difluoromethane:
• pentafluoroethane:
TWA
ppm
______
1000
TWA
mg/m³
______
4240
STEL
ppm
______
STEL
mg/m³
______
Peak
ppm
______
Peak
mg/m³
______
TWA
F/CC
______
Notes
______
CAS:75- 10- 5
CAS:354- 33- 6
MATERIAL DATA
AA:
DIFLUOROMETHANE:
PENTAFLUOROETHANE:
TETRAFLUOROETHANE:
Sensory irritants are chemicals that produce temporary and undesirable side-effects on the eyes, nose or throat. Historically
occupational exposure standards for these irritants have been based on observation of workers' responses to various airborne
concentrations.
DIFLUOROMETHANE:
PENTAFLUOROETHANE:
TETRAFLUOROETHANE:
May act as a simple asphyxiants; these are gases which, when present in high concentrations, reduce the oxygen content in air
below that required to support breathing, consciousness and life; loss of consciousness, with death by suffocation may rapidly
occur in an oxygen deficient atmosphere.
CARE: Most simple asphyxiants are odourless or possess low odour and there is no warning on entry into an oxygen deficient
atmosphere.
TETRAFLUOROETHANE:
Studies show that HFC 134a is practically nontoxic by inhalation. The acute lethal effects occur at levels exceeding 500000
ppm whilst the threshold for cardiac sensitisation occurs at about 75000 ppm. Repeated exposures at 50000 ppm for 13 weeks did
not produce significant toxicity in animals. Limited studies have shown the substance not to be a carcinogen, or to exhibit
mutagenic effects. Exposures up to 300000 ppm and 40000 ppm did not produce teratogenic effects in rats and rabbits respectively.
The workplace environmental exposure level (WEEL), recommended by the AIHA, is thought to be protective against cardiac
sensitisation and systemic injury.
PENTAFLUOROETHANE:
CEL TWA: 1000 ppm, 4240 mg/m3 [DuPont]
PERSONAL PROTECTION
RESPIRATOR
•Type GAX Filter of sufficient capacity. (AS/NZS 1716 & 1715, EN 143:2000 & 149:2001, ANSI Z88 or national equivalent)
EYE
• Safety glasses with side shields.
• Chemical goggles.
• Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document,
describing the wearing of lens or restrictions on use, should be created for each workplace or task. This should include a
review of lens absorption and adsorption for the class of chemicals in use and an account of injury experience. Medical and
first-aid personnel should be trained in their removal and suitable equipment should be readily available. In the event of
chemical exposure, begin eye irrigation immediately and remove contact lens as soon as practicable. Lens should be removed at
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 6 of 10
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
the first signs of eye redness or irritation - lens should be removed in a clean environment only after workers have washed
hands thoroughly. [CDC NIOSH Current Intelligence Bulletin 59], [AS/NZS 1336 or national equivalent].
HANDS/FEET
• When handling sealed and suitably insulated cylinders wear cloth or leather gloves.
OTHER
• Protective overalls, closely fitted at neck and wrist.
• Eye-wash unit.
• Ensure availability of lifeline in confined spaces.
• Staff should be trained in all aspects of rescue work.
ENGINEERING CONTROLS
■ Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed
engineering controls can be highly effective in protecting workers and will typically be independent of worker interactions to
provide this high level of protection.
The basic types of engineering controls are:
Process controls which involve changing the way a job activity or process is done to reduce the risk.
Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation
that strategically "adds" and "removes" air in the work environment.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE
Clear, colourless liquefied gas with ether-like odour; insoluble in water.
PHYSICAL PROPERTIES
Gas.
Does not mix with water.
State
Melting Range (°C)
Boiling Range (°C)
Flash Point (°C)
Decomposition Temp (°C)
Autoignition Temp (°C)
Upper Explosive Limit (%)
Lower Explosive Limit (%)
COMPRESSED GAS
Not Available
- 45.5
Not Applicable
Not Applicable
Not Applicable
Not Available
Not Available
Volatile Component (%vol)
Not Available
Molecular Weight
Viscosity
Solubility in water (g/L)
pH (1% solution)
pH (as supplied)
Vapour Pressure (kPa)
Specific Gravity (water=1)
Relative Vapour Density
(air=1)
Evaporation Rate
Not Applicable
Not Applicable
Immiscible
Not Applicable
Not Applicable
2.4621 @ 54.4C
Not Available
Not Available
Not Available
Section 10 - CHEMICAL STABILITY
CONDITIONS CONTRIBUTING TO INSTABILITY
• Presence of incompatible materials.
• Product is considered stable.
• Hazardous polymerisation will not occur.
• Extremely high temperatures.
For incompatible materials - refer to Section 7 - Handling and Storage.
Section 11 - TOXICOLOGICAL INFORMATION
Health hazard summary table:
Acute toxicity
Skin corrosion/irritation
Serious eye damage/irritation
Respiratory or skin sensitization
Not applicable
Not applicable
Not applicable
Not applicable
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
Germ cell mutagenicity
Carcinogenicity
Reproductive toxicity
STOT- single exposure
STOT- repeated exposure
Aspiration hazard
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 7 of 10
Section 11 - TOXICOLOGICAL INFORMATION
Not applicable
Not applicable
Not applicable
STOT SE 3
STOT SE 3
Not applicable
Not applicable
POTENTIAL HEALTH EFFECTS
ACUTE HEALTH EFFECTS
SWALLOWED
■ Not normally a hazard due to physical form of product.
■ Considered an unlikely route of entry in commercial/industrial environments.
EYE
■ Although the material is not thought to be an irritant (as classified by EC Directives), direct contact with the eye may
produce transient discomfort characterised by tearing or conjunctival redness (as with windburn).
■ Not considered to be a risk because of the extreme volatility of the gas.
SKIN
■ Skin contact is not thought to have harmful health effects (as classified under EC Directives); the material may still produce
health damage following entry through wounds, lesions or abrasions.
■ Repeated exposure may cause skin cracking, flaking or drying following normal handling and use.
■ There is some evidence to suggest that this material can cause inflammation of the skin on contact in some persons.
■ Fluorocarbons remove natural oils from the skin, causing irritation,dryness and sensitivity.
■ Open cuts, abraded or irritated skin should not be exposed to this material.
■ Entry into the blood-stream, through, for example, cuts, abrasions or lesions, may produce systemic injury with harmful effects.
Examine the skin prior to the use of the material and ensure that any external damage is suitably protected.
INHALED
■ Inhalation of vapours may cause drowsiness and dizziness.
This may be accompanied by sleepiness, reduced alertness, loss of reflexes, lack of co-ordination, and vertigo.
■ Inhalation of vapours or aerosols (mists, fumes), generated by the material during the course of normal handling, may be
damaging to the health of the individual.
■ There is some evidence to suggest that the material can cause respiratory irritation in some persons.
The body's response to such irritation can cause further lung damage.
■ Inhalation of non-toxic gases may cause:• CNS effects: headache, confusion, dizziness, stupor, seizures and coma;•
respiratory: shortness of breath and rapid breathing;•
cardiovascular: collapse and irregular heart beats;•
gastrointestinal: mucous membrane irritation, nausea and vomiting.
■ Acute intoxication by halogenated aliphatic hydrocarbons appears to take place over two stages.
Signs of a reversible narcosis are evident in the first stage and in the second stage signs of injury to organs may become
evident, a single organ alone is (almost) never involved.
■ Depression of the central nervous system is the most outstanding effect of most halogenated aliphatic hydrocarbons.
Inebriation and excitation, passing into narcosis, is a typical reaction.
■ Material is highly volatile and may quickly form a concentrated atmosphere in confined or unventilated areas.
The vapour
may displace and replace air in breathing zone, acting as a simple asphyxiant.
■ The use of a quantity of material in an unventilated or confined space may result in increased exposure and an irritating
atmosphere developing.
Before starting consider control of exposure by mechanical ventilation.
■ Exposure to fluorocarbons can produce non-specific flu-like symptoms such as chills, fever, weakness, muscle pain, headache,
chest discomfort, sore throat and dry cough with rapid recovery.
High concentrations can cause irregular heartbeats and a stepwise reduction in lung capacity.
CHRONIC HEALTH EFFECTS
Substance accumulation, in the human body, may occur and may cause some concern following repeated or long-term occupational
exposure.
Principal route of occupational exposure to the gas is by inhalation.
Fluorocarbons can cause an increased risk of cancer, spontaneous abortion and birth defects.
TOXICITY AND IRRITATION
■ Not available. Refer to individual constituents.
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 8 of 10
Section 12 - ECOLOGICAL INFORMATION
This material and its container must be disposed of as hazardous waste.
Ecotoxicity
Ingredient
tetrafluoroethane
Persistence:
Water/Soil
HIGH
difluoromethane
LOW
pentafluoroethane
HIGH
Persistence: Air
Bioaccumulation
Mobility
No Data
Available
No Data
Available
No Data
Available
LOW
HIGH
LOW
HIGH
LOW
MED
Section 13 - DISPOSAL CONSIDERATIONS
• Evaporate residue at an approved site.
• Return empty containers to supplier. If containers are marked non-returnable establish means of disposal with manufacturer
prior to purchase.
• Ensure damaged or non-returnable cylinders are gas-free before disposal.
Section 14 - TRANSPORTATION INFORMATION
Labels Required: NON-FLAMMABLE COMPRESSED GAS
HAZCHEM:
2TE (ADG7)
ADG7:
Class or Division:
UN No.:
Special Provision:
Portable Tanks & Bulk
Containers - Instruction:
Subsidiary Risk:
Packing Group:
Limited Quantity:
Portable Tanks & Bulk
Containers - Special
Provision:
Packagings & IBCs - Packing
P200
Packagings & IBCs - Special
Instruction:
Packing Provision:
Name and Description: LIQUEFIED GAS, N.O.S. (contains
tetrafluoroethane,difluoromethane and pentafluoroethane)
Air Transport IATA:
ICAO/IATA Class:
UN/ID Number:
Special provisions:
Cargo Only
Packing Instructions:
Passenger and Cargo
Packing Instructions:
Passenger and Cargo Limited Quantity
Packing Instructions:
2.2
3163
274
T50
None
None
120 ml
None
None
2.2
3163
None
ICAO/IATA Subrisk:
Packing Group:
None
-
200
Maximum Qty/Pack:
Passenger and Cargo
Maximum Qty/Pack:
Passenger and Cargo Limited Quantity
Maximum Qty/Pack:
150 kg
200
Forbidden
75 kg
Forbidden
Shipping name:LIQUEFIED GAS, N.O.S.(contains tetrafluoroethane,difluoromethane and pentafluoroethane)
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 9 of 10
Section 14 - TRANSPORTATION INFORMATION
Maritime Transport IMDG:
IMDG Class:
2.2
IMDG Subrisk:
None
UN Number:
3163
Packing Group:
None
EMS Number:
F-C,S-V
Special provisions:
274
Limited Quantities:
120 ml
Shipping name:LIQUEFIED GAS, N.O.S.(contains tetrafluoroethane,difluoromethane and pentafluoroethane)
Section 15 - REGULATORY INFORMATION
POISONS SCHEDULE None
REGULATIONS
Regulations for ingredients
C2-H2-F4 (CAS: 811-97-2) is found on the following regulatory lists;
"Australia - Australian Capital Territory - Environment Protection Regulation: Ambient environmental standards (AQUA/1 to 6 - nonpesticide anthropogenic organics)", "Australia - Australian Capital Territory - Environment Protection Regulation: Pollutants
entering waterways taken to cause environmental harm (Aquatic habitat)", "Australia Customs (Prohibited Exports) Regulations 1958
- Schedule 15 Ozone depleting substances - Part 9 HFCs", "Australia Exposure Standards", "Australia Hazardous Substances",
"Australia High Volume Industrial Chemical List (HVICL)", "Australia Inventory of Chemical Substances (AICS)", "OECD List of High
Production Volume (HPV) Chemicals", "Sigma-AldrichTransport Information"
CH2F2 (CAS: 75-10-5) is found on the following regulatory lists;
"Australia - Australian Capital Territory - Environment Protection Regulation: Ambient environmental standards (AQUA/1 to 6 - nonpesticide anthropogenic organics)", "Australia - Australian Capital Territory - Environment Protection Regulation: Ambient
environmental standards (Domestic water supply - inorganic chemicals)", "Australia - Australian Capital Territory - Environment
Protection Regulation: Ambient environmental standards (STOCK - inorganic chemicals)", "Australia - Australian Capital Territory Environment Protection Regulation: Pollutants entering waterways taken to cause environmental harm - Domestic water supply
quality", "Australia - Australian Capital Territory - Environment Protection Regulation: Pollutants entering waterways taken to
cause environmental harm (Aquatic habitat)", "Australia - Australian Capital Territory - Environment Protection Regulation:
Pollutants entering waterways taken to cause environmental harm (IRRIG)", "Australia - Australian Capital Territory - Environment
Protection Regulation: Pollutants entering waterways taken to cause environmental harm (STOCK)", "Australia - South Australia
Controlled Substances (Poisons) Regulations - Schedule E: Schedule 2 poisons authorised to be sold by holder of a medicine
sellers licence", "Australia Customs (Prohibited Exports) Regulations 1958 - Schedule 15 Ozone depleting substances - Part 9
HFCs", "Australia Drinking Water Guideline Values For Physical and Chemical Characteristics", "Australia Hazardous Substances",
"Australia Inventory of Chemical Substances (AICS)", "Australia National Pollutant Inventory", "Australia Standard for the
Uniform Scheduling of Medicines and Poisons (SUSMP) - Appendix F (Part 3)", "Australia Standard for the Uniform Scheduling of
Medicines and Poisons (SUSMP) - Schedule 2", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) Schedule 4", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 5", "Australia Standard
for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 6", "International Council of Chemical Associations (ICCA)
- High Production Volume List", "International Maritime Dangerous Goods Requirements (IMDG Code) - Substance Index", "OECD List
of High Production Volume (HPV) Chemicals", "Sigma-AldrichTransport Information", "WHO Guidelines for Drinking-water Quality Guideline values for chemicals that are of health significance in drinking-water"
C2-H-F5 (CAS: 354-33-6) is found on the following regulatory lists;
"Australia - Australian Capital Territory - Environment Protection Regulation: Ambient environmental standards (AQUA/1 to 6 - nonpesticide anthropogenic organics)", "Australia - Australian Capital Territory - Environment Protection Regulation: Ambient
environmental standards (Domestic water supply - inorganic chemicals)", "Australia - Australian Capital Territory - Environment
Protection Regulation: Ambient environmental standards (STOCK - inorganic chemicals)", "Australia - Australian Capital Territory Environment Protection Regulation: Pollutants entering waterways taken to cause environmental harm - Domestic water supply
quality", "Australia - Australian Capital Territory - Environment Protection Regulation: Pollutants entering waterways taken to
cause environmental harm (Aquatic habitat)", "Australia - Australian Capital Territory - Environment Protection Regulation:
Pollutants entering waterways taken to cause environmental harm (IRRIG)", "Australia - Australian Capital Territory - Environment
Protection Regulation: Pollutants entering waterways taken to cause environmental harm (STOCK)", "Australia - South Australia
Controlled Substances (Poisons) Regulations - Schedule E: Schedule 2 poisons authorised to be sold by holder of a medicine
sellers licence", "Australia Customs (Prohibited Exports) Regulations 1958 - Schedule 15 Ozone depleting substances - Part 9
HFCs", "Australia Drinking Water Guideline Values For Physical and Chemical Characteristics", "Australia Hazardous Substances",
"Australia Inventory of Chemical Substances (AICS)", "Australia National Pollutant Inventory", "Australia Standard for the
Uniform Scheduling of Medicines and Poisons (SUSMP) - Appendix F (Part 3)", "Australia Standard for the Uniform Scheduling of
Medicines and Poisons (SUSMP) - Schedule 2", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) Schedule 4", "Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 5", "Australia Standard
for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 6", "International Council of Chemical Associations (ICCA)
continued...
A-Gas R407F
Hazard Alert Code: MODERATE
Chemwatch GHS Safety Data Sheet
Issue Date: 7-Feb-2012
XC554SP
CHEMWATCH 30-2053
Version No:2.1.1.1
Page 10 of 10
Section 15 - REGULATORY INFORMATION
- High Production Volume List", "International Maritime Dangerous Goods Requirements (IMDG Code) - Substance Index", "OECD List
of High Production Volume (HPV) Chemicals", "WHO Guidelines for Drinking-water Quality - Guideline values for chemicals that are
of health significance in drinking-water"
No data for A-Gas R407F (CW: 30-2053)
Section 16 - OTHER INFORMATION
Denmark Advisory list for selfclassification of dangerous substances
Substance
CAS
Suggested codes
tetrafluoroethane
811- 97- 2
T; R25
■ Classification of the preparation and its individual components has drawn on official and authoritative sources as well as
independent review by the Chemwatch Classification committee using available literature references.
A list of reference resources used to assist the committee may be found at:
www.chemwatch.net/references.
■ The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether
the reported Hazards are Risks in the workplace or other settings.
This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or
criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written
permission from CHEMWATCH. TEL (+61 3) 9572 4700.
Issue Date: 7-Feb-2012
Print Date: 14-Mar-2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement