The World Models GM052 Ultimate EP Instruction Manual
THE WORLD MODELS GM052 is a quality electric powered precision model designed to provide maximum performance and enjoyment. When fully assembled, it has a 32.5-inch wingspan and weighs 24 ounces. With proper care and maintenance, this well-crafted model will provide years of exciting flying experiences. The GM052 is a versatile aircraft capable of various maneuvers, including aerobatic tricks. It is constructed from durable materials and features a lightweight design, making it easy to control and maneuver.
Here are some of the key features of the GM052:
- Impressive power: Powered by a strong propulsion system and an efficient motor, the GM052 delivers impressive power and speed, enabling you to execute various flight maneuvers with ease.
Advertisement
Advertisement
I NST RUCT I ON M ANUAL
.
(GM052)
Wing Span: 32.5 in / 825 mm
Wing Area: 357 sq in / 23 sq dm
Flying Weight: 24 oz / 680 g
Fuselage Length: 34 in / 870 mm
Requires: 4-channel radio w/ 3 micro servos. Outrunner
Motor KM0283011 w/ Propeller Adaptor HW2340100
20A Brushless ESC,3 cells 11.1V 1300 mAh Li-Po
battery & charger.
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
.
.
GM052XMPO28951303
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
P.1
P.2
P.3-
P.10
SAFETY PRECAUTIONS
BEFORE YOU BEGIN
P.10
1
2
3
Read through the manual before you begin, so you will have an overall idea of what to do.
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. For pre-assembled kits, please check proper functions of all servos on the ground before flying. Servo gears could be damaged when control surfaces are hit during transportation of models. The manufacturer will replace any servos due to manufacturer`s defect, but will not cover plane crashes due to damaged servos not detected before flying.
Symbols used throughout this instruction manual comprise of the following :-
Apply epoxy glue.
Apply instant glue
(C.A.glue, super glue.)
Apply thread locker Must be purchased separately !
3mm
Assemble left and right sides the same way.
Peel off shaded portion covering film.
Drill holes with the specified diameter (here: 3mm).
Pay close attention here!
GM052XMPO28951303
P.1
Ensure smooth non-binding movement while assembling.
Cut off shaded portion.
Pierce the shaded portion covering film.
Warning!
Do not overlook this symbol !
Parts List
1.MAIN WING -- 1 set
PLASTIC BRACKET -- 2 pcs
FIBRE TAPE 17x380mm -- 4 pcs
2.BALL JOINT CONTROL ARM PL4203100 -- 2 sets
SCREW PM2.5x12mm -- 2 pcs
WASHER d2.5xD8mm -- 2 pcs
PUSHROD Ø1.4x92mm w/ Threads (For Aileron) -- 2 pcs
STRAPER PL4112106 -- 2 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
3.FUSELAGE -- 1 set
STABILIZER & ELEVATOR -- 1 set
FIBRE TAPE 17x240mm -- 1 pc.
4.VERTICAL FIN & RUDDER -- 1 set
FIBRE TAPE 17x215mm -- 1 pc.
PLASTIC BRACKET -- 2 pcs
5.TAIL LANDING GEAR PL3410030 --1 set
SCREW PA2x8mm -- 2 pcs
TAIL WHEEL Ø23mm PL3510230 -- 1 pc.
PLASTIC BRACKET -- 2 pcs
6.MAIN LANDING GEAR -- 1 set
COLLAR Ø2.6mm w/ Set Screw -- 2 sets
PLYWOOD COLLAR Ø8x2mm -- 2 pcs
MAIN WHEEL Ø40mm PL3116040 -- 2 pcs
SCREW PA2.6x8mm -- 1 pc.
PLYWOOD 26x20.4x2.5mm (For Main Landing Gear) -- 1 pc.
MAIN LANDING GEAR COVER -- 1 pair
WHEEL PANT -- 1 pair
MOUNTING PLATE PL4114020 -- 2 pcs
SCREW PWA2x6mm -- 4 pcs
7.CLEVIS PL4112105 -- 1 pc.
STRAPER PL4112106 -- 1 pc.
HORN PL4113103 -- 1 pc.
PUSHROD Ø1.4x73mm w/ Threads (For Elevator) -- 1 pc.
FUEL TUBE d2xD4x4mm -- 2 pcs
8.CLEVIS PL4112105 -- 1 pc.
STRAPER PL4112106 -- 1 pc.
HORN PL4113103 -- 1 pc.
PUSHROD Ø1.4x133mm w/ Threads (For Rudder) -- 1 pc.
FUEL TUBE d2xD4x4mm -- 2 pcs
9.SOCKET HEAD SCREW M3x6mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
SPINNER Ø36mm -- 1 set
PROPELLER PL6314050 -- 1 set
10.CANOPY -- 1 pc.
11.SIDE CABANE -- 2 pcs
CENTER CABANE -- 1 pc.
12.
PUSHROD Ø1.4x125mm w/ Threads (For Elevator) -- 2 pcs
CLEVIS PL4112105 -- 4 pcs
HORN PL4113103 -- 4 pcs
FUEL TUBE d2xD4x4mm -- 4 pcs
13.BATTERY COVER -- 1 pc.
BATTERY TIE 160mm-- 1 pc.
BATTERY MAT 2x50x150mm -- 2 pcs
DOUBLE-SIDED TAPE 30x35mm (For Brushless ESC) -- 1 pc.
14.DECALS: GM052 DEC -- 1 set
GM052XMPO28951303
P.2
1
Main Wing
Upper
Fibre Tape Bottom
Fibre Tape 17x380 mm
Lower
Bottom View
Plastic Bracket
Fibre Tape 17x380 mm
2
Aileron Servo Lower Wing
PM2 . 5 x 12mm Screw d2.5xD8mm Washer
2
Ball Joint Control Arm
Washer d2.5xD8mm
PM2.5x12mm
Bottom View
Straper
Fuel Tube d2xD4x4mm
Pushrod
Ø 1.4x92mm
TWM PL8210010
CLEVIS WRENCH
GM052XMPO28951303
Bottom View
P.3
3
Stabilizer & Elevator
Bottom Fibre Tape
Fibre Tape 17x240 mm
Joining surfaces should be clean and dry. Slightly roughen surfaces with sandpaper for best results.
Bottom View
Vertical Fin & Rudder
Fibre Tape
17x215 mm
Fibre Tape
Plastic Bracket
Joining surfaces should be clean and dry. Slightly roughen surfaces with sandpaper for best results.
Tail Landing Gear
PA2x8mm Screw
2
PA2x8mm
Wheel Ø23mm
Plastic Bracket
1.2mm
GM052XMPO28951303 P.4
Completed
Bottom View
6
Main Landing Gear
PA2.6x8mm Screw
1
PWA2x6mm Screw
4
2.6mm Collar w/ Set Screw
2
10
0
Fuselage
Landing Gear
Plywood
26x20.4x2.5mm
Landing Gear
Bottom View
Completed
7
Elevator Pushrod
Bottom View
PA2.6x8mm
Bottom View
Landing Gear Covers
Bottom View
Mounting Plate
12x20mm
PWA2x6mm M3x3mm Set Screw
Wheel Pants
Landing Gear
Plywood Collar Ø8x2mm
2.6mm Collar
Wheel Ø40mm
90°
Fuel Tube d2xD4x4mm
Straper
Clevis
Fuel Tube d2xD4x4mm Horn
TWM PL8210010
CLEVIS WRENCH
GM052XMPO28951303 P.5
Bottom View
8
Rudder Pushrod
TWM PL8210010
CLEVIS WRENCH
Fuel Tube d2xD4x4mm
Pushrod
Ø1.4x133mm
Straper
Horn
Clevis
Pushrod
Ø1.4x133mm
Fuel Tube d2xD4x4mm
90°
Bottom View
9
Outrunner Motor / Spinner
M3x6mm Socket Head Screw
4
PM2x12mm Screw
2
PA1.7x8mm Screw
2 d3xD7mm Washer
4
Optional Parts
Outrunner Motor 28/ 30
KM0283011
Propeller Adaptor
(d3xD5) HW2340100
Make sure rotating motor casing is not in contact with wirings or anything.
M3x6mm d3xD7mm Washer
1
ESC
Solder
GM052XMPO28951303
EZ Connector
Brushless ESC
2
PM2x12mm
3
Solder
Motor
TWM
KP0011310
9x6 Propeller
PL6314050 d6xD15mm Washer
4
M5 Nut
TWM HW3111400
PROPELLER ADAPTOR WRENCH
P.6
PM2x12mm
Don’t over-tighten the PM2 screws, let the propeller blades align themselves when spinning.
PA1.7x8mm
5
Ø36mm Spinner
Completed
10
Canopy
Canopy
11
Wing Setting
Joining surfaces should be clean and dry. Slightly roughen surfaces with sandpaper for best results.
Side Cabane
Center Cabane
GM052XMPO28951303
A=A` B=B` C=C`
A
C
B B`
P.7
A`
C`
Completed
12
Main Wing
Main Wing (Upper)
Horn
Clevis
Fuel Tube d2xD4x4mm
Pushrod
Ø1.4x125mm
Clevis
Horn
Main Wing (Lower)
13
Radio Equipment
Install and arrange the equipment as shown in the picture.
Battery Tie
Battery
Receiver
Battery Mat
Battery Cover
Completed
GM052XMPO28951303 P.8
14
Decals
F0
F1-L
F2-L
F3-L
W1-L
W2-L
W3-L W4-L
W5-L
W0
F4-L
F6
W1-R
W4-R
W5-R
W3-R
W2-R
F5-L
GM052XMPO28951303 P.9
15
Control Throws
Elevator
Rudder
Ailerons
15mm
15mm
25mm
25mm
Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference.
5mm
5mm
16
C.G.
The ideal C.G. position is 77mm (3 in.) behind the leading edge center apex of the upper wing. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.
77mm
3.03 in.
C.G.
http://www.thewingsmaker.com/instructionManuals.php
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer
is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by KM0283011 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller. Extreme caution should be exercised when working with
electric powered models. Make sure the propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure you understand the
operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one,
as accidental movement of the throttle stick will spin the propeller and could cause injuries.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
GM052XMPO28951303 P.10
www.thewingsmaker.com
GM052XMPO28951303
THE WINGS MAKER

Public link updated
The public link to your chat has been updated.
Advertisement