Winco HPS9000VE/C Specifications

Winco HPS9000VE/C Specifications
Generators
Industrial Portable Generators
3kW - 18kW
Mobile Diesel Power Systems
25kVA - 80kVA
Two Bearing Generators
2kW - 8kW
Consumer Portable Generators
3kW - 6kW
Tri-Fuel Portable Generators
6kW - 12kW
PSS Packaged Standby Systems
8kW - 75kW
Vehicle Mount Generators
20kW - 75kW
PTO Generators
15kW - 150kW
For All Your Power Needs
www.wincogen.com
Powered by
NEF45 AM1
4.5 Liter/Normally Aspirated
Electrical Output 45kW/56kVa
Voltage
120/240
120/208
120/240
277/480
Amperes
150
150
135
68
Cycles
60
60
60
60
Phase
1
3
3
3
kW
45
45
45
45
kVa
45
56
56
56
pf
1.0
0.8
0.8
0.8
STANDARD FEATURES
• IVECO 4.5 Liter 1800 RPM Engine (Division of FIAT Motors)
- Meets EPA / CARB Tier 2 Emissions
- Mechanical Governor
- Fuel/Water Separator
- Oil Drain Extension with Valve
• BASLER DGC-2020 Digital Controller with Automatic Safety
Shutdowns and Digital Readouts for Low Oil Pressure, High Water
Temp, Engine Overcrank and Engine Overspeed, Low Fuel Level
Shutdown, Battery Disconnect Switch
• Brushless Alternator / Class H Insulation
– Standby Output: 45kW (56kVA)
– Prime Output: 40.5kW (50.6kVA)
– Motor Starting Capability: 20 h.p. Code F
– Voltage Regulation: 1.5% / < 5% Total Harmonic Distortion
• SWITCHABLE 4-Position Voltage Selector Switch with
Automatic Safety Shutdown and Safety Lock Out
− AC Voltages - 3 Phase: 208, 220, 240, 416, 440, 460, 480V
− AC Voltages - 1 Phase: 120, 139, 208, 220, 240V
Amps: - Single Phase 240V: 150A (at terminal block)
- Three Phase 208V: 150A
- Three Phase 240V: 135A
- Three Phase 480V: 68A
• Illuminated Instrumentation Panel and Connection Box
• Receptacle Package:
- 2-50amp 120/240V Twistlock Receptacles
- 2-20amp 120V GFCI Duplex Receptacles
- 1-Terminal Block for Full Connection with Safety Shut Off
• Shore Power Inlet for Easy Connection to Block Heater
and Battery Charger
225 South Cordova Ave
Le Center MN 56057 USA
• Pre-wired for Remote Emergency Stop (Optional Button Available)
• Two Wire Remote Start Capability
• Selectable High or Low Voltage Mainline Circuit Breakers
for Main Power Connection
• Circuit Breakers for Single Phase Receptacles
• 14-gauge Galvanneal Steel Sound Attenuated Enclosure
with Critical Muffler
• Sound Level: 68 dB(A) 7 Meters, Full Load
• Durable Powder Coat Paint Finish / Stainless Steel Fasteners
• Large Lockable Doors for Maintenance Access
• Single Point Lifting Eye
• Full Fluid Containment System with Drains
• Lockable Fuel Access Door
• Six Bolts to Remove Generator Assembly from Trailer
• DOT Approved Trailer & Tank, 7,000 lb. Capacity,
Electric Brakes with Break-Away
Kit, Single Axle,
Torsion Bar Suspension, Front Leveling Jack, Rear
Stabilization Jacks, Running Lights, Lighted License Plate Bracket
• 110-gallon, 7-gauge Steel Fuel Tank
• Fuel Consumption:
• Run Time:
Full Load..........2.80 gal/hr
Full Load.......39 hours
75% Load.........2.11 gal/hr
75% Load......52 hours
50% Load.........1.41 gal/hr
50% Load......78 hours
• Removable and Adjustable Hitch
• 3” Pintle Hitch and 2 5/16” Ball Hitch both come Standard
• Large Front Lockable Storage Compartment
• Dimensions: Generator with Trailer - 150” x 66” x 83”
• Weight: Generator with Dry Fuel Tank and Trailer - 4760 lbs
• Warranty: Complete Unit - 1 Year; Engine - 2 Year Limited
FL 0609
Telephone: (507) 357-6821
Fax: (507) 357-4857
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
Why Winco Industrial Portables?
♦ Winco Generators-Quality & Innovation since 1927
♦ WC Series comes standard with:
o Conserv-R automatic idle control saves on fuel and
reduces noise
o Switchless Full Power allows the full rated output from a
single 120 volt or 240 volt outlet, or combination of both
at the same time without switching voltage settings
(applicable on the WC5000H and WC6000H/HE)
o Hour meter
♦ High quality generator ends, built to last
♦ 100% copper windings assure longer life expectancy
♦ Clean low harmonic power, won’t burn up sensitive equipment
♦ High motor starting capabilities that are able to start larger
motors
♦ Brushless generator ends (except for WC6000H/HE)
♦ WC6000H/HE has a Rotating Field Brush design for superior
motor starting
♦ Equipped with name brand industrial engines such as Honda and
Briggs & Stratton Vanguard
o Service and parts distributors available nationwide
♦ CARB & EPA certified premium engines
♦ Industrial grade mufflers
♦ Rubber isolation mounts on engine and generator
♦ Large fuel tanks for longer run times on 4kW and larger
♦ Heavy duty tubular steel cradles to handle and protect the
everyday use of your generator. Std 1” and 1 ¼” 13- gauge
tubular steel
♦ Industrial powder coated paint baked onto the cradle and other
key components
♦ Wide variety of receptacles, all have circuit breaker protection
♦ Compact size for easier transportation and handling
♦ Four wheel dolly kit and lifting eye are standard on both
WC12000HE and WL18000VE
♦ 100% of generators are load tested, not statistically sampled as
some manufacturers do
INDUSTRIAL
PORTABLE
GENERATORS
WINCO’s broad industrial portable line offers just the right generator for the
job at hand. All generator models include the following features: Powder paint
finish on rugged wrap-around welded tubular cradles; CARB / EPA approved
premium engines with low oil protection; sizes ranging from 3,000 watts to
18,000 watts; large fuel tanks and GFCI’s standard on models 4,000 watts
and larger. All WC models also include: Switchless Full Power TM which allows
the full rated output from a single 120 volt or 240 volt outlet, or combination of
both, without switching voltage settings; Conserv-R R automatic idle control;
hour meter and fuel cap with gauge; full receptacle panel with circuit breakers.
A Tradition Since 1927
* ENGINES: Premium Honda and Briggs & Stratton Vanguard CARB and EPA certified engines equipped with low oil
protection and industrial grade mufflers * FRAMES: Heavy duty tubular steel cradles protect the generator; rubber
isolation mounts on engine and generator, compact size for easy transportation and handling * FUEL TANKS: Large 4.5,
7.0 and 15.0 gallon fuel tanks for longer run times on 4kW and larger * CONTROL PANELS: Easy-access; wide variety of
receptacles; circuit breaker protection * SUPERIOR GENERATOR END: 100% copper windings; high motor starting
capabilities; self-regulating output voltage; built to last * FEATURES/STANDARDS: All units are 100% load tested; USFSapproved spark arrestors; WC models have Conserv-R R automatic idle control and hour meter.
WT3000H
MODEL NUMBER
WC6000H/
WC6000HE
WC5000H
WT3000H
Electrical Specifications
Maximum Power Rating
3000 watts
Continuous Power Rating
2500 watts
A.C. Output Voltage
120 volts
Continuous Current Rating
20.8 amps
Motor Starting Ability (1)
1.0 hp
120 Volt Full PowerTM (3)
N/A
Generator Type (4)
R.F.L
Engine Data
Make/Model
Honda GX160
Displacement/Type
160 cc/OHV
Conserv-R R Automatic Idle Control
N/A
Low Oil Protection
Standard
Starting System (5)
Recoil
Fuel Tank Capacity
1.0 Gallon
Running Time-Full Load
2.2 hours
Running Time-Half Load
3.1 hours
Hour Meter
N/A
120 Volt Receptacles
Straight Blade (NEMA 5-20R)
4-20 amp
Twist Lock (NEMA L5-20R) GFCI Protected
Straight Blade (NEMA 5-30R)
Straight Blade (NEMA 5-50R)
240 Volt Receptacles
Twist Lock (NEMA L6-20R)
Twist Lock (NEMA L6-30R)
Straight Blade (NEMA 6-50R)
120/240 Volt Receptacles
Twist-Lock (NEMA L14-30R)
N/A
Straight Blade (NEMA 14-60R)
Size & Weight
Dimensions (LxWxH)
24x16x18 in.
Shipping Weight
102 lbs.
Warranty Information (8)
Generator/Engine
2 yrs/3 yrs
CSA Approved
Yes
WC5000H
WC6000H
WC6000HE
5000 watts
4500 watts
120/240 volts
37.5/18.8 amps
1.5 hp
37.5 amps
R.F.L.
6000 watts
5500 watts
120/240 volts
45.8/22.9 amps
3.0 hp
45.8 amps
R.F.B.
6000 watts
5500 watts
120/240 volts
45.8/22.9 amps
3.0 hp
45.8 amps
R.F.B.
Honda GX270
270 cc/OHV
Standard
Standard
Recoil
4.5 Gallons
6.6 hours
10.3 hours
Standard
Honda GX340
337 cc/OHV
Standard
Standard
Recoil
4.5 Gallons
5.2 hours
9.8 hours
Standard
Honda GX340
337 cc/OHV
Standard
Standard
Recoil/Electric
4.5 Gallons
5.2 hours
9.8 hours
Standard
4-20 amp GFCI
2-20 amp
4-20 amp GFCI
2-20 amp
4-20 amp GFCI
2-20 amp
1-50 amp
1-50 amp
1-50 amp
1-20 amp
1-20 amp
1-20 amp
1-30 amp
1-30 amp
1-30 amp
32x22x22 in.
226 lbs.
32x22x22 in.
251 lbs.
32x22x22 in.
262 lbs.
2 yrs/3 yrs
Yes
2 yrs/3 yrs
Yes
2 yrs/3 yrs
Yes
Notes: (1) Code G capacitor start motor (2) Consult factory or authorized dealer for complete details. (3) Available 120 volts at the 50 amp
Full Power plug. (4) R.F.B. is a Rotating Field Brush design, R.F.L. is a Rotating Field Brushless design (capacitor excitation) and R.A.B. is
a Rotating Armature Brush type generator. (5) Electric start models include battery rack and cables; battery not included. (6) Model WC6000H
is recoil start only; model WC6000HE has both recoil and electric start. (7) On 240 volts only. NOTE: Models WC12000HE and WL18000VE
come with wheel kit and lifting eye standard. (8) Engine warranty applies to retail purchases made after January 1, 2009.
WINCO Inc. continually improves its products and reserves the right to change designs, materials and/or specifications without notice and
without incurring any obligations to make such changes or improvements on products previously purchased.
WC12000HE
WL18000VE
W6010DEX
W9500HE
Diesel
MODEL NUMBER
Electrical Specifications
Maximum Power Rating
Continuous Power Rating
A.C. Output Voltage
Continuous Current Rating
Motor Starting Ability (1)
120 Volt Full Power TM (3)
Generator Type (4)
Engine Data
Make/Model
Displacement/Type
Conserv-R R Automatic Idle Control
Low Oil Protection
Starting System (5)
Fuel Tank Capacity
Running Time-Full Load
Running Time-Half Load
Hour Meter
120 Volt Receptacles
Straight Blade (NEMA 5-20R)
Twist Lock (NEMA L5-20R) GFCI Protected
Straight Blade (NEMA 5-30R)
Straight Blade (NEMA 5-50R)
240 Volt Receptacles
Twist Lock (NEMA L6-20R)
Twist Lock (NEMA L6-30R)
Straight Blade (NEMA 6-50R)
120/240 Volt Receptacles
Twist-Lock (NEMA L14-30R)
Straight Blade (NEMA 14-60R)
Size & Weight
Dimensions (LxWxH)
Shipping Weight
Warranty Information (8)
Generator/Engine
CSA Approved
W9500HE
WC12000HE WL18000VE
W6010DEX
9500 watts
8500 watts
120/240 volts
70.8/35.4 amps
5 hp (7)
45.8 amps
R.F.L
12000 watts
10800 watts
120/240 volts
90/45 amps
6 hp
N/A
R.F.L.
18000 watts
15000 watts
120/240 volts
125/62.5 amps
7.5 hp
N/A
R.F.L.
6000 watts
5500 watts
120/240 volts
45.8/22.9 amps
3.0 hp
45.8 amps
R.F.L.
Honda GX610
610 cc/OHV
N/A
Standard
Electric
4.5 Gallon
3.2 hours
5.3 hours
N/A
Honda GX620
620 cc/OHV
Standard
Standard
Electric
15 Gallons
9.0 hours
14.5 hours
Standard
B&S Vanguard
895 cc/OHV
N/A
Standard
Electric
15 Gallons
6.8 hours
10.5 hours
Standard
Hatz 1B40
462 cc
N/A
Standard
Electric
7.0 Gallons
10.0 hours
20.0 hours
Standard
4-20 amp GFCI
2-20 amp
4-20 amp GFCI
1-20 amp
4-20 amp GFCI
2-20 amp
2-20 amp GFCI
1-50 amp
1-50 amp
1-30 amp
1-30 amp
1-30 amp
1-60 amp
1-60 amp
32x22x22 in.
306 lbs.
39.5x26.5x26 in.
440 lbs.
42x27x29 in.
550 lbs.
2 yrs/3 yrs
No
2 yrs/3 yrs
No
2 yrs/2 yrs
No
1-50 amp
1-20 amp
1-50 amp
1-30 amp
1-30 amp
32x22x22 in.
300 lbs.
2 yrs/2 yrs or 2000 hrs
No
Notes: (1) Code G capacitor start motor (2) Consult factory or authorized dealer for complete details. (3) Available 120 volts at the 50 amp
Full Power plug. (4) R.F.B. is a Rotating Field Brush design, R.F.L. is a Rotating Field Brushless design (capacitor excitation) and R.A.B. is
a Rotating Armature Brush type generator. (5) Electric start models include battery rack and cables; battery not included. (6) Model WC6000H
is recoil start only; model WC6000HE has both recoil and electric start. (7) On 240 volts only. NOTE: Models WC12000HE and WL18000VE
come with wheel kit and lifting eye standard. (8) Engine warranty applies to retail purchases made after January 1, 2009.
WINCO Inc. continually improves its products and reserves the right to change designs, materials and/or specifications without notice and
without incurring any obligations to make such changes or improvements on products previously purchased.
WINCO offers a complete line of accessories to enhance the performance,
versatility and safety of your WINCO Industrial Generator.
All-Terrain 2-Wheel Dolly Kit - The ultimate in portability is provided
in this accessory. The 10” diameter pneumatic tires get you through
mud, snow, sand and soggy lawns. Durable grip handles assure easy
maneuverability. Available for all models 4000 watts and larger.
(Note: 4-Wheel kit is standard on models WC12000HE and WL18000VE)
All-Terrain 4-Wheel Dolly Kit - This accessory has the same
rugged durability as our 2-wheel kit, but with the easy mobility of
4 wheels. Available for all models 6000 through 9500 watts.
(Note: 4-Wheel kit is standard on models WC12000HE and WL18000VE)
Single Point Lifting Bar - With this accessory, your WINCO
portable generator can be moved by crane from floor to floor on
multi-story construction sites or suspended for overnight security.
The Single Point Lifting Bar is easily attached to the frame.
Available on all models 4000 watts and larger. (Note: Single Point
Lifting Bar is standard on models WC12000HE and WL18000VE)
Generator Cover - This durable tailored cover is made of heavy
canvas to protect your WINCO portable generator in all weather
conditions. During storage or transportation, the custom generator
cover protects your portable generator from moisture, dust, nicks
and scratches. A built-in band keeps the cover in place in high winds.
Line Voltage Monitor - This compact voltmeter can be plugged
into the 120-volt receptacle on any WINCO generator to assure
you that your generator is functioning properly. Available for all
models.
Emergency Transfer/Service System - The ET/S System allows
120/240 volt rated WINCO portable generators to be quickly and
safely connected to building wiring for emergency/standby service
during a power outage. A wall-mount enclosure with hinged cover
and padlock to prevent unauthorized access contains a 12 foot cord
with a special connecting plug. The enclosure is mounted on the
outside of the building and stores the cordset when not in use. A
quality Square D circuit breaker load center installs next to the building
electrical service panel.The load center has interlocked generator and
utility main breakers to prevent feedback to the utility. Four 120 volt
(or 8 tandem) or two 240 volt branch circuits, or a combination of the
two, can be connected for emergency service. Can be used on all models
with the L14-30R or 14-60R receptacle (please specify when ordering).
Manual Transfer Switches also available - contact
WINCO for details.
Tel: (507) 357-6821 Fax: (507) 357-4857
East Coast Sales: (800) 733-2112
West Coast Sales & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
W/WC 10/09
225 South Cordova Avenue
Le Center, MN 56057 USA
Why Winco Consumer Portables?
♦ Winco Generators-Quality & Innovation since 1927
♦ Premium CARB & EPA certified Honda or Briggs and Stratton
engines
♦ Service and parts distributors available nationwide
♦ 100% copper windings assure longer life expectancy
♦ Light, compact design for convenient storage and transport
♦ Large fuel tanks for longer run times on 5kW and larger
♦ Wide variety of receptacles, all have circuit breaker protection
♦ WC Series comes standard with:
o Low oil protection
o Industrial grade mufflers
♦ High quality generator ends, built to last
♦ Clean low harmonic power, won’t burn up sensitive equipment
♦ High motor starting capabilities that are able to start larger
motors
♦ Rubber isolation mounts on engine and generator
♦ Heavy duty tubular steel cradles to handle and protect the
everyday use of your generator. Std 1” and 1 ¼” 13- gauge
tubular steel
♦ Industrial powder coated paint baked onto the cradle and other
key components
♦ 100% of generators are load tested, not statistically sampled as
some manufacturers do
♦ 5000 and up come with full power 4-wire receptacle for home
standby.
Portable Generators by
D3000H
DL6000I
DYNA FEATURES
n
PREMIUM CARB/EPA APPROVED HONDA OR BRIGGS & STRATTON ENGINES
n
ALL COPPER WINDINGS AND CIRCUIT BREAKERS FOR OPERATOR SAFETY
AND PROTECTION AGAINST DAMAGING OVERLOADS
n
STURDY WRAP-AROUND WELDED TUBULAR CRADLES
n
DURABLE, LONG LASTING POWDER PAINT FINISH
n
LIGHT, COMPACT DESIGN FOR CONVENIENT STORAGE AND TRANSPORT
n
LARGE FUEL TANKS FOR LONGER RUN TIMES (5kW AND LARGER)
n
SIZES RANGING FROM 3kW TO 6kW
225 South Cordova Ave
Le Center MN 56057 USA
Telephone: (507) 357-6821
Fax: (507) 357-4857
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
D3000H
DL5000H
DL6000I
DL6000H
PERFORMANCE & TECHNICAL DATA
Model Number
D3000H
DL5000H
DL6000I/
DL6000IE
DL6000H/
DL6000HE
5000 watts
4500 watts
120/240 volts
37.4/18.7 amps
1.5 hp
6000 watts
5500 watts
120/240 volts
45.8/22.9 amps
2 hp
6000 watts
5500 watts
120/240 volts
45.8/22.9 amps
2 hp
Honda GX270
270 cc/OHV
Recoil
4.5 Gallons
Standard
6.6 hours
10.3 hours
B&S/Intek
342 cc/OHV
(3)
4.5 Gallons
Standard
5.3 hours
8.5 hours
Honda GX340
337 cc/OHV
(3)
4.5 Gallons
Standard
4.5 hours
6.4 hours
2-20 amp
4-20 amp
4-20 amp
1-30 amp
1-30 amp
1-30 amp
30x19x22 in.
150 lbs.
26.25x18x21.4 in.
158/168 lbs.
30x22x22 in.
202/210 lbs.
2 yrs/3 yrs
No
2 yrs/2 yrs
Yes
2 yrs/3 yrs
No
Electrical Specifications
Maximum Power Rating
3000 watts
Continuous Power Rating**
2300 watts
A.C. Output Voltage
120 volts
Continuous Current Rating
19.1 amps
Motor Starting Ability (1)
.75 hp
Engine Data
Make/Model
Honda GC160
Displacement/Type
160 cc/OHC
Starting System (2)
Recoil
Fuel Tank Capacity
2 Qt.
Low Oil Protection
Standard
Running Time-Full Load
1.1 hours
Running Time-Half Load
1.5 hours
Receptacles
Straight Blade (NEMA 5-20R)
2-20 amp
120/240 Volt Receptacles
Twist-Lock (NEMA L14-30R)
N/A
Size & Weight
Dimensions (LxWxH)
20.75x15x16 in.
Shipping Weight
92 lbs.
Warranty Information - Consumer Application (4)(5)
Generator/Engine
2 yrs/2 yrs
CSA Approved
Yes
NOTES: (1) Code G Capacitor Start Motor. (2) Electric start models include battery rack and cables. Battery not included.
(3) Models DL6000I and DL6000H are recoil start only. Models DL6000IE and DL6000HE have both recoil and electric start.
(4) Engine warranty applies to retail purchases made after January 1, 2009. (5) Commercial or Prime Power (Off-Grid)
Warranty - 90 Days; International Warranty - Contact WINCO for details.
** Power Output +/- 5%
DYNA 1/09
120
TEL: (507) 357-6821 FAX: (507) 357-4857
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
olt
DL6000I & DL6000IE
PORTABLE GENERATORS
FOR HOME AND
LIGHT INDUSTRIAL USE
Compact, convenient, low-profile design
Powerful Briggs & Stratton industrial OHV engine
Electric or recoil start models
Heavy duty generator with clean sine wave
Large 4-1/2 gallon fuel tank
CSA (Canadian Standards Association) approved
Building on nearly 80 years of experience, WINCO proudly introduces the
new DL6000I and DL6000IE. Powered
by the industrial Briggs & Stratton
11HP OHV Intek engine, these units
are built with industrial components at
a consumer-friendly price. A newly
designed receptacle package features
four 20-amp 120-volt receptacles and a
full power 30-amp receptacle, all with
circuit breaker protection. The heavy
duty brushless alternator design
minimizes maintenance by eliminating
carbon brushes and slip rings common
on competitive models, while simultaneously delivering voltage stability and
clean power. The new Advance Power
Series by DYNA is the perfect solution
for reliable, industrial strength power
for home back-up.
225 South Cordova Ave
Le Center MN 56057
TYPICAL POWER LOADS
LIghts
TV, VCR/DVD Player, Stereo
Computer, Monitor, Printer
Microwave Oven
Dishwasher
Toaster, Electric Fry Pan
Hair Dryer
Space Heater
Portable Fan
Furnace Fan
Sump Pump
Refrigerator, Freezer
Drill (hand-held)
Electric Hand Saw
Portable Air Compressor
Air Conditioner (window-mount)
Air Conditioner (central air)
POWER REQUIRED*
As listed on light bulbs
150-300 watts
800-1200 watts
600-1500 watts
900-1200 watts
1200 watts
800-1200 watts
1200-1500 watts
200-300 watts
500-800 watts
500-1200 watts
800-1500 watts
600-900 watts
1200-1500 watts
1200-1500 watts
1200-1500 watts
4000-6000 watts
* Approximate power required for each item
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
Web Site: www.wincogen.com
E-Mail: [email protected]
DL6000I & DL6000IE
PORTABLE GENERATORS
“BUILDING ON EXPERIENCE”
PERFORMANCE & TECHNICAL DATA**
Electrical Specifications
Maximum Power Rating (1)
Continuous Power Rating (1)
A C Output Voltage
Continuous Current Rating
Motor Starting Ability (2)
Engine Data
Make/Model
Displacement/Type
Rated Power (3600 rpm)
Starting System
Fuel Tank Capacity
Low Oil Protection
Running Time - Full Load
Running Time - Half Load
Receptacles
120V Straight Blade (NEMA 5-20R)
120/240V Twistlock (NEMA L14-30R)
Size & Weight
Dimensions (LxWxH)
Shipping Weight
Warranty Information-Consumer Application (3)
Generator/Engine
NOTES:
(1) Power Output - +/- 5%.
(2) Code G Capacitor Start Motor.
(3) Commercial or Prime Power Use (off-grid) Warranty - 90
Days; International Warranty - Contact WINCO for details.
** Unit is CSA (Canadian Standards Association) Approved
DL6000I
6000 watts
5500 watts
120/240 volts
45.8/22.9 amps
1.5 hp
DL6000IE
6000 watts
5500 watts
120/240 volts
45.8/22.9 amps
1.5 hp
B&S/Intek
342 cc/OHV
11 hp
Recoil
4.5 gallon
Standard
5.3 hours
8.5 hours
B&S/Intek
342 cc/OHV
11 hp
Recoil/Elec
4.5 gallon
Standard
5.3 hours
8.5 hours
4-20 amp
1-30 amp
4-20 amp
1-30 amp
26.25x17.5x21.4”
158 lbs.
26.25x17.5x21.4”
168 lbs.
2 yrs/2 yrs
2 yrs/2 yrs
225 South Cordova Avenue
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
Web Site: www.wincogen.com
E-Mail: [email protected]
DL/AP 9/05
Why Winco Tri-Fuel Portables?
♦ Winco Generators-Quality & Innovation since 1927
♦ Proven, dependable, efficient design, since 1984
♦ Dual Carburetors allows the engine to operate on gasoline, LP
gas, or natural gas with no adjustment.
♦ Premium Honda and Briggs & Stratton Vanguard OHV engines.
High quality generator ends, built to last
♦ 100% copper windings assure longer life expectancy
♦ Clean low harmonic power, won’t burn up sensitive equipment
♦ Service and parts distributors available nationwide
♦ Rubber isolation mounts on engine and generator
♦ Heavy duty tubular steel cradles to handle and protect the
everyday use of your generator. Std 1” and 1 ¼” 13- gauge
tubular steel
♦ Industrial powder coated paint baked onto the cradle and other
key components
♦ Wide variety of receptacles, includes full power 4-wire for home
standby, all have circuit breaker protection
♦ Compact size for easier transportation and handling
♦ Four wheel dolly are standard on HPS12000HE
♦ 100% of generators are load tested, not statistically sampled as
some manufacturers do
♦ Home Power Series comes standard with:
o Electric start with battery rack and cables
o Maintenance-free electron ignition system
o Dual element air filter reduces maintenance
o Low oil protection helps prevent costly repairs and
downtime.
♦ Optional Accessories:
o All Terrain 2 Wheel Dolly Kit
o Generator Cover
o Line Voltage Monitor
o Gen-Tran Manual Transfer Switches
o Emergency Transfer/Service System
o Low Pressure Fuel Solenoid
TRI-FUEL PORTABLE GENERATORS by
HPS6000HE
HPS12000HE
HPS9000VE
HOME POWER ® Tri-Fuel Portable Generators by WINCO keep you out of the dark. The unit
operates on gasoline, L.P. gas, or natural gas, and converting from one fuel source to another can be
accomplished quickly and easily. HOME POWER ® Tri-Fuel generators are powered by premium
quality, long-life engines with low oil protection. The powerful, high-quality generator features inherent
voltage regulation and protection for optimum reliability and safety. 120/240 volt A.C. single-phase,
60-cycle electric power is available through the receptacles provided in the output panel. The sturdy
cradle design provides full protection and makes handling and storage easy.
Features/Benefits
Engine
• Premium Honda and Briggs & Stratton Vanguard
OHV engines meet EPA emissions standards
• Special carburetor and secondary gas regulator
allows the engine to operate on the most
convenient fuel-gasoline, L.P. gas or natural gas
• Low oil protection helps prevent costly repairs and
downtime
• Standard electric start with battery rack and cables
(battery not included)
• Maintenance-free electronic ignition system
• Dual element air filter reduces maintenance
Generator
• Proven, dependable, efficient design
• Inherent voltage regulation for precise, stable
output and optimum reliability
• 100% copper windings, NEMA Class F insulation
• Capacitor excitation for brushless operation
Power Output Panel
• Special 120/240 volt receptacle for connection
to a temporary power distribution system or to
a building electrical service with an approved
manual transfer switch for emergency/standby
use
• Standard straight blade, U-ground 120 volt
duplex receptacles
• Circuit breaker overload protection on generator
Protective Cradle
• Heavy-duty tubular steel cradle with distinctive
wrap-around design for added strength and
durability
• Vibration isolation for smooth operation
• Large capacity fuel tank allows for extended
run time between refills when using gasoline
fuel
• Easy to move, convenient to store
HPS 1/09
TRI-FUEL PORTABLE GENERATORS by
MODEL NUMBER
HPS6000HE
HPS9000VE
HPS12000HE
6000 watts
5500 watts
120/240 volts
45.8/22.9 amps
2 h.p.
9000 watts
8000 watts
120/240 volts
66.7/33.3 amps
4 h.p.
12,000 watts
10,800 watts
120/240 volts
90/45 amps
6 h.p.
Honda GX340
337 cc/OHV
Electric/Recoil
4.5 gallons
Standard
B&S Vanguard
480 cc/OHV
Electric/Recoil
4.5 gallons
Standard
Honda GX620
620 cc/OHV
Electric
15.0 gallons
Standard
1.0 gal/hr
1.1 gal/hr
77 cu ft/hr
72 DbA
1.3 gal/hr
1.5 gal/hr
121 cu ft/hr
77 DbA
1.67 gal/hr
2.2 gal/hr
195 cu ft/hr
78 DbA
2-20 amp
1-30 amp
N/A
4-20 amp
1-30 amp
N/A
4-20 amp
1-30 amp
1-60 amp
30x22x22 in.
212 lbs.
32x22x22 in.
274 lbs.
39.5x26x26 in.
396 lbs.
1 yr/3 yrs
2 yrs/2 yrs
1 yr/3 yrs
Electrical Specifications
Maximum Power Rating (1)
Continuous Power Rating (1)
AC Output Voltage
Continuous Current Rating
Motor Starting Ability (1)(2)
Engine Data
Make/Model
Displacement/Type
Starting System (3)
Fuel Tank Capacity (gasoline)
Low Oil Protection
Fuel Consumption - Full Load
* Gasoline
* L.P.
* Natural Gas
DbA Rating (@ 7 meters)
Receptacles
120 Volt Straight Blade (NEMA 5-20R)
120/240 Volt Twist-Lock (NEMA L14-30R)
120/240 Volt Straight Blade (NEMA 14-60R)
Size & Weight
Dimensions (LxWxH)
Shipping Weight
Warranty Information - Consumer Application (4)(5)
Generator/Engine
ACCESSORIES
All-Terrain 2-Wheel Dolly Kit – The ultimate in portability, this wheel kit with 8”
diameter pneumatic tires and durable grip handles gets you through mud, snow, sand
and soggy terrain. NOTE: HPS12000HE comes with 4-Wheel Dolly Kit standard.
All-Terrain 2-Wheel
Dolly Kit
Generator Cover – This durable tailored cover is made of heavy canvas to protect
your Home Power generator during storage or transportation. The custom cover
protects against moisture, dust, nicks and scratches. A built-in band keeps the cover
in place in high winds.
Line Voltage Monitor – This compact voltmeter can be plugged into the 120 volt
receptacle on any Home Power generator to assure you that your generator is
functioning properly or assist you in isolating continuity problems in extension cords.
Gen-Tran Manual Transfer Switches – 8 circuit, 30-amp or 12 circuit, 60-amp
UL approved manual transfer switches allow generator connection to electrical service
for emergency power backup. 30-amp system includes power inlet box and 25-foot
connection cord in NEMA 1 enclosure. 60-amp system is flush-mount.
Emergency Transfer/Service System – The ET/S System allows your Home Power
generator to be quickly and safely connected to a building electrical panel for backup
service during a power outage. A weatherproof NEMA 3R hinged lockable enclosure
contains a 12-foot cord with a special twist-lock plug and stores the cordset when not
in use. A quality Square D circuit breaker load center with interlocked generator and
utility main breakers to prevent feedback to the utility installs next to the building
electrical service panel. Four 120-volt (or 8 tandem) or two 240-volt branch circuits or
a combination of the two can be connected for emergency service.
Low Pressure Fuel Solenoid (12-volt) – Units that are intended to be run unattended
or for long periods of time must have an electric fuel solenoid installed in the fuel line
close to the generator. This solenoid is a positive flow shut-off valve which shuts off
the fuel should the engine unexpectedly stop running, preventing costly and dangerous
fuel leakage at the connection point.
Generator Cover
LIne Voltage Monitor
Emergency
Transfer/Service Kit
NOTE: (1) Based on gasoline fuel. Derate 10% for L.P. gas, 20% for Natural Gas. (2) Code G capacitor start motor.
(3) Electric start models include battery rack and cables. Battery not included. BCI Group U1, 12-volt, 235 CCA battery
required. (4) Engine warranty applies to retail purchases made after January 1, 2009. (5) Commercial or Prime Power
Warranty – 90 Days. International Warranty – Contact WINCO for details.
225 South Cordova Avenue
Le Center, MN 56057 USA
Tel: (507) 357-6821 Fax: (507) 357-4857
Sales (E of Mississippi River): (800) 733-2112
Sales (W of Mississippi River & Canada): (800) 324-8174
Warranty/Service: (507) 357-6821/6832
E-Mail: [email protected]
Web Site: www.wincogen.com
Powered by
4LE1
2.2 Liter
Naturally Aspirated
Electrical Output 20kW/25kVa
Voltage
Amperes
Cycles
Phase
kW
kVa
pf
120/240
70*
60
1
20
20
1.0
120/208
69
60
3
20
25
0.8
120/240
60
60
3
20
25
0.8
277/480
30
60
3
20
25
0.8
* Available amperage at terminal block connection - additional amperage available at receptacle panel for single phase output.
STANDARD FEATURES
• ISUZU 2.2 Liter 1800 RPM Engine
- Meets EPA / CARB Tier 2 Emissions
- Mechanical Governor
- Fuel/Water Separator
- Oil Drain Extension with Valve
• BASLER DGC-2020 Digital Controller with Automatic Safety
Shutdowns and Digital Readouts for Low Oil Pressure, High Water
Temp, Engine Overcrank and Engine Overspeed, Low Fuel Level
Shutdown, Battery Disconnect Switch
• Brushless Alternator / Class H Insulation
– Standby Output: 20kW (25kVA)
– Prime Output: 18kW (22.5kVA)
– Motor Starting Capability: 7.5 h.p. Code G
– Voltage Regulation: 1.5% / < 5% Total Harmonic Distortion
• SWITCHABLE 4-Position Voltage Selector Switch with
Automatic Safety Shutdown and Safety Lock Out
− AC Voltages - 3 Phase: 208, 220, 240, 416, 440, 460, 480V
− AC Voltages - 1 Phase: 120, 139, 208, 220, 240V
Amps: - Single Phase 240V: 70A (at terminal block)
- Three Phase 208V: 69A
- Three Phase 240V: 60A
- Three Phase 480V: 30A
• Illuminated Instrumentation Panel and Connection Box
• Receptacle Package:
- 2-50amp 120/240V Twistlock Receptacles
- 2-20amp 120V GFCI Duplex Receptacles
- 1-Terminal Block for Full Connection with Safety Shut Off
• Shore Power Inlet for Easy Connection to Block Heater
and Battery Charger
• Pre-wired for Remote Emergency Stop (Optional Button Available)
• Two Wire Remote Start Capability
• Selectable High or Low Voltage Mainline Circuit Breakers
for Main Power Connection
• Circuit Breakers for Single Phase Receptacles
• 14-gauge Galvanneal Steel Sound Attenuated Enclosure
with Critical Muffler
• Sound Level: 65.9 dB(A) @ 7 Meters, Full Load
• Durable Powder Coat Paint Finish / Stainless Steel Fasteners
• Large Lockable Doors for Maintenance Access
• Single Point Lifting Eye
• Full Fluid Containment System with Drains
• Lockable Fuel Access Door
• Six Bolts to Remove Generator Assembly from Trailer
• DOT Approved Trailer & Tank, 3,500 lb. Capacity,
Electric Brakes with Break-Away Kit, Single Axle,
Torsion Bar Suspension, Front Leveling Jack, Rear
Stabilization Jacks, Running Lights, Lighted License Plate Bracket
• 45-gallon, 7-gauge Steel Fuel Tank
• Fuel Consumption:
• Run Time:
Full Load..........1.8 gal/hr
Full Load.......25 hours
75% Load.........1.4 gal/hr
75% Load......32 hours
50% Load..........9 gal/hr
50% Load......50 hours
• Removable and Adjustable Hitch
• 3” Pintle Hitch and 2 5/16” Ball Hitch both come Standard
• Large Front Lockable Storage Compartment
• Dimensions: Generator with Trailer - 135” x 58” x 73”
• Weight: Generator with Dry Fuel Tank and Trailer - 2820 lbs
• Warranty: Complete Unit - 1 Year; Engine - 2 Year Limited
APPLICATION &
ENGINEERING DATA
EXPERIENCED DESIGN
GENSET CONTROL
•
•
•
•
•
•
•
•
OVER 80 YEARS EXPERIENCE IN
THE GENERATOR INDUSTRY
DESIGNED FOR LONG LIFE
TO MAXIMIZE RETURN
ON INVESTMENT
REACTIVE L0AD BANK
TESTED / SINGLE STEP 100%
LOAD TESTED
“ORIGINATOR” OF THE MOBILE
DIESEL GENERATOR
•
•
•
BASLER DGC-2020 DIGITAL CONTROLLER
GENERATOR PROTECTION AND METERING
EVENT FAULT LOG RECORDING
DEDICATED RELAYS FOR FUEL SOLENOIDS,
GLOW PLUGS AND STARTER SOLENOID
AUTOMATIC SAFETY SHUTDOWN
DIGITAL READOUTS FOR LOW OIL PRESSURE,
HIGH WATER TEMP, ENGINE OVERCRANK
AND ENGINE OVERSPEED
LOW FUEL LEVEL SHUTDOWN
ENGINE SPECIFICATIONS
GENERATOR SPECIFICATIONS
•
•
•
•
EPA CARB TIER 2 COMPLIANT ( TIER 4 READY )
COMPLETE SERVICE NETWORK
EFFICIENT LOW FUEL CONSUMPTION DESIGN
BRUSHLESS ROTATING FIELD FOR LONG LIFE
AND LOW MAINTENANCE
• MEETS BS EN 60034, BS5000, VDE 0530
• NEMA MG1-32, ICE34, CSA C22.2-100, AS1359
• INCLUDES: HIGH EFFICIENCY SEMICONDUCTORS,
RECTIFIER SURGE PROTECTION
• STANDARD OUTPUT: 20kW, 25kVA
• PRIME OUTPUT: 18kW, 22.5kVA
• AMPS: 1-PHASE 240V - 70A at terminal block,
83 amps total, including receptacle panel
3-PHASE 208V - 69A
3-PHASE 240V - 60A
3-PHASE 480V - 30A
RATING..............................................(125/40°C) STANDBY
TYPE....................................4 POLE – REVOLVING FIELD
SPEED/FREQUENCY..................................1800 RPM/60HZ
INSULATION SYSTEM..........................................CLASS H
STATOR WINDINGS......DOUBLE LAYER CONCENTRIC
PITCH.................................................................................2/3
WAVEFORM DISTORTION...........................................1.5%
TELEPHONE INTERFERENCE..................................<2.0%
EFFICIENCY PEAK...................................................~92.5%
COUPLING..................................................FLEXIBLE DISC
BEARINGS (MAINTENANCE FREE).................................1
CONTROL...............(SX460 STANDARD) SELF EXCITED
REGULATION...........................................................+/- 1.5%
SINGLE PHASE RATING...............................................1.0pf
THREE PHASE RATING................................................0.8pf
MAKE.....................................................................................ISUZU
MODEL......................................................................................4LE1
TYPE.....................................................................................DIESEL
DIRECT INJECTION...............................................MECHANICAL
SPEED GOVERNOR...............................................MECHANICAL
CYLINDERS....................................................................................4
TOTAL DISPLACEMENT..........................................................2.2L
BORE X STROKE.........................................................mm 85 X 95
COMPRESSION........................................................................2.5:1
ASPIRATION/COOLING..................................NATURAL/LIQUID
RADIATOR CAPACITY.........................................................2 GAL
TOTAL COOLING CAPACITY.........................................2.75 GAL
HOUSING................................................................................SAE 4
FLYWHEEL (TEETH 125).......................................................10 in.
ROTATION...............................................................................CCW
LUBE OIL SPEC.......................................SAE TYPE, API CF-CH4
LUBE OIL CONSUMPTION.................................< 0.1% OF FUEL
OIL & FILTER REPLACEMENT........................................500 HRS
TOTAL OIL CAPACITY...........................................................8.69L
EXHAUST OUTLET SIZE @ MUFFLER..................................1.5”
ELECTRICAL SYSTEM (NEGATIVE GROUND)..............12 VDC
ALTERNATOR (BOSCH)..................................................35 AMPS
STARTER..............................................................................DENSO
BATTERY (NOT INCLUDED BCI 24)..............................650 CCA
Telephone: (507) 357-6821
Fax: (507) 357-4857
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
RP25-0108
225 South Cordova Ave
Le Center MN 56057 USA
Powered by
NEF45 AM1
4.5 Liter
Naturally Aspirated
Electrical Output 45kW/56kVa
Voltage
120/240
120/208
120/240
277/480
Amperes
150
150
135
68
Cycles
60
60
60
60
Phase
1
3
3
3
kW
45
45
45
45
kVa
45
56
56
56
pf
1.0
0.8
0.8
0.8
STANDARD FEATURES
• IVECO 4.5 Liter 1800 RPM Engine (Division of FIAT Motors)
- Meets EPA / CARB Tier 2 Emissions
- Mechanical Governor
- Fuel/Water Separator
- Oil Drain Extension with Valve
• BASLER DGC-2020 Digital Controller with Automatic Safety
Shutdowns and Digital Readouts for Low Oil Pressure, High Water
Temp, Engine Overcrank and Engine Overspeed, Low Fuel Level
Shutdown, Battery Disconnect Switch
• Brushless Alternator / Class H Insulation
– Standby Output: 45kW (56kVA)
– Prime Output: 40.5kW (50.6kVA)
– Motor Starting Capability: 20 h.p. Code F
– Voltage Regulation: 1.5% / < 5% Total Harmonic Distortion
• SWITCHABLE 4-Position Voltage Selector Switch with
Automatic Safety Shutdown and Safety Lock Out
− AC Voltages - 3 Phase: 208, 220, 240, 416, 440, 460, 480V
− AC Voltages - 1 Phase: 120, 139, 208, 220, 240V
Amps: - Single Phase 240V: 150A (at terminal block)
- Three Phase 208V: 150A
- Three Phase 240V: 135A
- Three Phase 480V: 68A
• Illuminated Instrumentation Panel and Connection Box
• Receptacle Package:
- 2-50amp 120/240V Twistlock Receptacles
- 2-20amp 120V GFCI Duplex Receptacles
- 1-Terminal Block for Full Connection with Safety Shut Off
• Shore Power Inlet for Easy Connection to Block Heater
and Battery Charger
• Pre-wired for Remote Emergency Stop (Optional Button Available)
• Two Wire Remote Start Capability
• Selectable High or Low Voltage Mainline Circuit Breakers
for Main Power Connection
• Circuit Breakers for Single Phase Receptacles
• 14-gauge Galvanneal Steel Sound Attenuated Enclosure
with Critical Muffler
• Sound Level: 68 dB(A) 7 Meters, Full Load
• Durable Powder Coat Paint Finish / Stainless Steel Fasteners
• Large Lockable Doors for Maintenance Access
• Single Point Lifting Eye
• Full Fluid Containment System with Drains
• Lockable Fuel Access Door
• Six Bolts to Remove Generator Assembly from Trailer
• DOT Approved Trailer & Tank, 7,000 lb. Capacity,
Electric Brakes with Break-Away Kit, Single Axle,
Torsion Bar Suspension, Front Leveling Jack, Rear
Stabilization Jacks, Running Lights, Lighted License Plate Bracket
• 110-gallon, 7-gauge Steel Fuel Tank
• Fuel Consumption:
• Run Time:
Full Load..........2.80 gal/hr
Full Load.......39 hours
75% Load.........2.11 gal/hr
75% Load......52 hours
50% Load.........1.41 gal/hr
50% Load......78 hours
• Removable and Adjustable Hitch
• 3” Pintle Hitch and 2 5/16” Ball Hitch both come Standard
• Large Front Lockable Storage Compartment
• Dimensions: Generator with Trailer - 150” x 66” x 83”
• Weight: Generator with Dry Fuel Tank and Trailer - 4760 lbs
• Warranty: Complete Unit - 1 Year; Engine - 2 Year Limited
APPLICATION &
ENGINEERING DATA
EXPERIENCED DESIGN
GENSET CONTROL
•
•
•
•
•
•
•
•
OVER 80 YEARS EXPERIENCE IN
THE GENERATOR INDUSTRY
DESIGNED FOR LONG LIFE
TO MAXIMIZE RETURN
ON INVESTMENT
REACTIVE L0AD BANK
TESTED / SINGLE STEP 100%
LOAD TESTED
“ORIGINATOR” OF THE MOBILE
DIESEL GENERATOR
•
•
•
BASLER DGC-2020 DIGITAL CONTROLLER
GENERATOR PROTECTION AND METERING
EVENT FAULT LOG RECORDING
DEDICATED RELAYS FOR FUEL SOLENOIDS,
GLOW PLUGS AND STARTER SOLENOID
AUTOMATIC SAFETY SHUTDOWN
DIGITAL READOUTS FOR LOW OIL PRESSURE,
HIGH WATER TEMP, ENGINE OVERCRANK
AND ENGINE OVERSPEED
LOW FUEL LEVEL SHUTDOWN AND FUEL LEAK
DETECTION ALARM
ENGINE SPECIFICATIONS
GENERATOR SPECIFICATIONS
•
•
•
•
•
BRUSHLESS ROTATING FIELD FOR LONG LIFE AND
LOW MAINTENANCE
• MEETS BS EN 60034, BS5000, VDE 0530
• NEMA MG1-32, ICE34, CSA C22.2-100, AS1359
• INCLUDES: HIGH EFFICIENCY SEMICONDUCTORS,
RECTIFIER SURGE PROTECTION
• STANDARD OUTPUT: 45kW, 55kVA
• PRIME OUTPUT: 40.5kW, 50.6kVA
• AMPS: 1-PHASE 240V - 150A at terminal block,
188 amps total, including receptacle panel
3-PHASE 208V - 150A
3-PHASE 240V - 135A
3-PHASE 480V - 68A
RATING..............................................(125/40°C) STANDBY
TYPE....................................4 POLE – REVOLVING FIELD
SPEED/FREQUENCY..................................1800 RPM/60HZ
INSULATION SYSTEM..........................................CLASS H
STATOR WINDINGS......DOUBLE LAYER CONCENTRIC
PITCH.................................................................................2/3
WAVEFORM DISTORTION...........................................1.5%
TELEPHONE INTERFERENCE..................................<2.0%
EFFICIENCY PEAK...................................................~92.5%
COUPLING..................................................FLEXIBLE DISC
BEARINGS (MAINTENANCE FREE).................................1
CONTROL...............(SX460 STANDARD) SELF EXCITED
REGULATION...........................................................+/- 1.5%
SINGLE PHASE RATING...............................................1.0pf
THREE PHASE RATING................................................0.8pf
DIVISION OF FIAT MOTORS INC.
EPA CARB TIER 2 COMPLIANT ( TIER 4 READY )
COMPLETE SERVICE NETWORK
EFFICIENT LOW FUEL CONSUMPTION DESIGN
MAKE.....................................................................................IVECO
MODEL..........................................................................NEF45 AM1
TYPE.....................................................................................DIESEL
DIRECT INJECTION...............................................MECHANICAL
SPEED GOVERNOR...............................................MECHANICAL
CYLINDERS....................................................................................4
MEAN PISTON SPEED.........................................................7.9 m/s
TOTAL DISPLACEMENT..........................................................4.5L
BORE X STROKE.....................................................mm 104 X 132
COMPRESSION......................................................................17.5:1
ASPIRATION/COOLING..................................NATURAL/LIQUID
RADIATOR CAPACITY....................................................2.25 GAL
TOTAL COOLING CAPACITY...........................................4.5 GAL
HOUSING................................................................................SAE 3
FLYWHEEL (TEETH 125)....................................................11½ in.
ROTATION...............................................................................CCW
LUBE OIL SPEC.......................................SAE TYPE, API CF-CH4
LUBE OIL CONSUMPTION.................................< 0.1% OF FUEL
OIL & FILTER REPLACEMENT........................................600 HRS
TOTAL OIL CAPACITY.............................................13.5 QUARTS
EXHAUST OUTLET SIZE @ MUFFLER..................................2.5”
ELECTRICAL SYSTEM (NEGATIVE GROUND)..............12 VDC
ALTERNATOR (BOSCH)..................................................90 AMPS
STARTER..............................................................................BOSCH
BATTERY (NOT INCLUDED BCI 24)..............................650 CCA
Telephone: (507) 357-6821
Fax: (507) 357-4857
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
RP55-0807
225 South Cordova Ave
Le Center MN 56057 USA
Powered by
NEF45 SM2
4.5 Liter
Turbocharged
Electrical Output 65kW/80kVa
Voltage
Amperes
Cycles
Phase
kW
kVa
pf
120/240
225*
60
1
65
65
1.0
120/208
225
60
3
65
80
0.8
120/240
195
60
3
65
80
0.8
277/480
98
60
3
65
80
0.8
* Available amperage at terminal block connection - additional amperage available at receptacle panel for single phase output.
STANDARD FEATURES
• IVECO 4.5 Liter 1800 RPM Engine (Division of FIAT Motors)
- Meets EPA / CARB Tier 2 Emissions
- Mechanical Governor
- Fuel/Water Separator
- Oil Drain Extension with Valve
• BASLER DGC-2020 Digital Controller with Automatic Safety
Shutdowns and Digital Readouts for Low Oil Pressure, High Water
Temp, Engine Overcrank and Engine Overspeed, Low Fuel Level
Shutdown, Battery Disconnect Switch
• Brushless Alternator / Class H Insulation
– Standby Output: 65kW (80kVA)
– Prime Output: 58.5kW (72kVA)
– Motor Starting Capability: 25 h.p. Code G
– Voltage Regulation: 1.5% / < 5% Total Harmonic Distortion
• SWITCHABLE 4-Position Voltage Selector Switch with
Automatic Safety Shutdown and Safety Lock Out
− AC Voltages - 3 Phase: 208, 220, 240, 416, 440, 460, 480V
− AC Voltages - 1 Phase: 120, 139, 208, 220, 240V
Amps: - Single Phase 240V: 225A (at terminal block)
- Three Phase 208V: 225A
- Three Phase 240V: 195A
- Three Phase 480V: 98A
• Illuminated Instrumentation Panel and Connection Box
• Receptacle Package:
- 2-50amp 120/240V Twistlock Receptacles
- 2-20amp 120V GFCI Duplex Receptacles
- 1-Terminal Block for Full Connection with Safety Shut Off
• Shore Power Inlet for Easy Connection to Block Heater
and Battery Charger
• Pre-wired for Remote Emergency Stop (Optional Button Available)
• Two Wire Remote Start Capability
• Selectable High or Low Voltage Mainline Circuit Breakers
for Main Power Connection
• Circuit Breakers for Single Phase Receptacles
• 14-gauge Galvanneal Steel Sound Attenuated Enclosure
with Critical Muffler
• Sound Level: 70 dB(A) @ 7 Meters, Full Load
• Durable Powder Coat Paint Finish / Stainless Steel Fasteners
• Large Lockable Doors for Maintenance Access
• Single Point Lifting Eye
• Full Fluid Containment System with Drains
• Lockable Fuel Access Door
• Six Bolts to Remove Generator Assembly from Trailer
• DOT Approved Trailer & Tank, 7,000 lb. Capacity,
Electric Brakes with Break-Away Kit, Single Axle,
Torsion Bar Suspension, Front Leveling Jack, Rear
Stabilization Jacks, Running Lights, Lighted License Plate Bracket
• 110-gallon, 7-gauge Steel Fuel Tank
• Fuel Consumption:
• Run Time:
Full Load..........4.64 gal/hr
Full Load.......24 hours
75% Load.........3.48 gal/hr
75% Load......32 hours
50% Load.........2.41 gal/hr
50% Load......46 hours
• Removable and Adjustable Hitch
• 3” Pintle Hitch and 2 5/16” Ball Hitch both come Standard
• Large Front Lockable Storage Compartment
• Dimensions: Generator with Trailer - 150” x 66” x 83”
• Weight: Generator with Dry Fuel Tank and Trailer - 4950 lbs
• Warranty: Complete Unit - 1 Year; Engine - 2 Year Limited
APPLICATION &
ENGINEERING DATA
EXPERIENCED DESIGN
GENSET CONTROL
•
•
•
•
•
•
•
•
OVER 80 YEARS EXPERIENCE IN
THE GENERATOR INDUSTRY
DESIGNED FOR LONG LIFE
TO MAXIMIZE RETURN
ON INVESTMENT
REACTIVE L0AD BANK
TESTED / SINGLE STEP 100%
LOAD TESTED
“ORIGINATOR” OF THE MOBILE
DIESEL GENERATOR
•
•
•
BASLER DGC-2020 DIGITAL CONTROLLER
GENERATOR PROTECTION AND METERING
EVENT FAULT LOG RECORDING
DEDICATED RELAYS FOR FUEL SOLENOIDS,
GLOW PLUGS AND STARTER SOLENOID
AUTOMATIC SAFETY SHUTDOWN
DIGITAL READOUTS FOR LOW OIL PRESSURE,
HIGH WATER TEMP, ENGINE OVERCRANK
AND ENGINE OVERSPEED
LOW FUEL LEVEL SHUTDOWN AND FUEL LEAK
DETECTION ALARM
ENGINE SPECIFICATIONS
GENERATOR SPECIFICATIONS
•
•
•
•
•
DIVISION OF FIAT MOTORS INC.
EPA CARB TIER 2 COMPLIANT ( TIER 4 READY )
COMPLETE SERVICE NETWORK
EFFICIENT LOW FUEL CONSUMPTION DESIGN
BRUSHLESS ROTATING FIELD FOR LONG LIFE
AND LOW MAINTENANCE
• MEETS BS EN 60034, BS5000, VDE 0530
• NEMA MG1-32, ICE34, CSA C22.2-100, AS1359
• INCLUDES: HIGH EFFICIENCY SEMICONDUCTORS,
RECTIFIER SURGE PROTECTION
• STANDARD OUTPUT: 65kW, 80kVA
• PRIME OUTPUT: 58.5kW, 72kVA
• AMPS: 1-PHASE 240V - 225A at terminal block,
270 amps total, including receptacle panel
3-PHASE 208V - 225A
3-PHASE 240V - 195A
3-PHASE 480V - 98A
RATING..............................................(125/40°C) STANDBY
TYPE....................................4 POLE – REVOLVING FIELD
SPEED/FREQUENCY..................................1800 RPM/60HZ
INSULATION SYSTEM..........................................CLASS H
STATOR WINDINGS......DOUBLE LAYER CONCENTRIC
PITCH.................................................................................2/3
WAVEFORM DISTORTION...........................................1.5%
TELEPHONE INTERFERENCE..................................<2.0%
EFFICIENCY PEAK...................................................~92.5%
COUPLING..................................................FLEXIBLE DISC
BEARINGS (MAINTENANCE FREE).................................1
CONTROL...............(SX460 STANDARD) SELF EXCITED
REGULATION...........................................................+/- 1.5%
SINGLE PHASE RATING...............................................1.0pf
THREE PHASE RATING................................................0.8pf
MAKE.....................................................................................IVECO
MODEL..........................................................................NEF45 SM2
TYPE.....................................................................................DIESEL
DIRECT INJECTION...............................................MECHANICAL
SPEED GOVERNOR...............................................MECHANICAL
CYLINDERS....................................................................................4
TOTAL DISPLACEMENT..........................................................4.5L
BORE X STROKE.....................................................mm 104 X 132
ASPIRATION/COOLING....................TURBOCHARGED/LIQUID
RADIATOR CAPACITY....................................................2.25 GAL
TOTAL COOLING CAPACITY...........................................5.0 GAL
HOUSING................................................................................SAE 3
FLYWHEEL (TEETH 125)....................................................11½ in.
ROTATION...............................................................................CCW
LUBE OIL SPEC.......................................SAE TYPE, API CF-CH4
LUBE OIL CONSUMPTION.................................< 0.1% OF FUEL
OIL & FILTER REPLACEMENT........................................600 HRS
TOTAL OIL CAPACITY.............................................13.5 QUARTS
EXHAUST OUTLET SIZE @ MUFFLER..................................3.0”
ELECTRICAL SYSTEM (NEGATIVE GROUND)..............12 VDC
ALTERNATOR (BOSCH)..................................................90 AMPS
STARTER..............................................................................BOSCH
BATTERY (NOT INCLUDED BCI 24)..............................650 CCA
Telephone: (507) 357-6821
Fax: (507) 357-4857
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
RP80-1007
225 South Cordova Ave
Le Center MN 56057 USA
~Since 1927~
Why Choose Winco Standbys?
Winco provides the best components and superior performance in
every packaged standby system we manufacture.
Generator
Engine
All Winco Package Standby Systems produce clean
electrical power with low harmonic distortion for
sensitive equipment and computers.
o Meets all UL voltage and frequency
regulation standards
o Total harmonic distortion <5%
o Skewed rotor design
o Rotating field brushless
o Automatic voltage regulation
o Liquid cooled models only
o Class H insulation
o Class H is rated at 356° F vs. Class F
which is only rated at 311° F
o Main line circuit breaker included
All PSS systems come with industrial grade engines
o Briggs & Stratton Vanguard
o V-Twin OHV & V-Twin Big Block OHV
o Cast iron cylinder sleeves
o Steel backed aluminum bearings
o Spin on oil filter
o Low oil consumption
o Honda OHV
o V-Twin OHV
o Oil alert
o 12V electric start
o Automotive style oil filter
o Oil cooler
o Ford 1.6L 4-cylinder
o 3600 rpm, liquid cooled
o Electronic governor & ignition
o Blockheater std
o Critical grade muffler
o Battery tender(charger) std
o GM 3.0L, 4.3L, 5.7L, & 5.7L Turbo
o 1800 rpm, liquid cooled
o Electronic governor & ignition
o Blockheater std
o Critical grade muffler
o Battery tender(charger) std
Benefits
o Industrial grade quality that is built to last
o Nationwide distributor of engine parts
Housing
o 14-gauge galvanneal steel housing to
reduce rusting
o 10-gauge steel base
o Lockable doors
o Aluminum hinges
o 1” sound absorbing foam
o Industrial DuPont powder coat paint
o Peaked roofs on all liquid cooled models to
prevent standing water
o Stainless steel and Stallguard coated torx
sheet metal screws with nylon washers
o Each individual piece of sheet metal is
stamped, washed, painted, and tested
before final assembly
o Rubber isolation mounts on engine and
generator
o Compact design takes up less space
o Weather resistant enclosures
o Rodent proof
225 South Cordova Ave.
Le Center, MN 56057
PHONE: (507) 357-6821
FAX: (507) 357-4857
SALES (E of the Mississippi River): (800) 733-2112
SALES (W of the Mississippi River): (800) 324-8174
WARRANTY/SERVICE: (507) 357-6831/6832
WEB SITE: www.wincogen.com
Don’t let the next
power outage
interrupt your life!
Stay comfortable and secure with a
dependable back up power system from
Providing Power Solutions Since 1927,
WINCO Is Your Only Choice
For Back Up Power Convenience!
www.wincogen.com
Automatic Packaged Standby Systems Designed
For Homes, Businesses and Industrial Applications
Why Buy An Automatic Standby System?
An automatic standby generator is a permanently installed, fully automatic emergency generator system that continuously monitors the
incoming utility power supply. The system is designed to automatically furnish electrical power to pre-selected circuits in your home that
supply your lighting, heating and cooling, appliances and water. There’s no need for extension cords, gasoline cans for refueling, or manual
start pull ropes because WINCO’s Packaged Standby System supplies back up electric power automatically.
Powered by premium engines, WINCO packaged standby systems are perfect for back up power. Sound attenuated, weather protective
enclosures are made using galvannealed steel with a powder paint finish for long life durability. The solid state control system operates the
generator automatically when signalled by the automatic transfer switch mounted next to your incoming service panel. Standard features
include: cycle crank and overcrank limiting, engine start delay and engine cool down timing, hour meters and battery chargers.
Features of
•
•
•
•
•
•
Automatic Standby Generators
Easily installed outside new or existing homes
Direct natural gas or LP fuel systems
Low maintenance
Emissions compliant
Critical grade silencer for quieter operation
Hinged Doors
• Generator set and components are factory built and tested
to NEMA standards
• Sound attenuated housings constructed of galvannealed
•
steel with durable baked powder paint finish keeps your
generator attractive long into the future
Standard mainline circuit breakers
How Does The System Work?
• An automatic transfer switch (ATS) monitors your
utility power and provides 100% isolation between
your generator and the utility power. If the incoming
power fails, the ATS will send a start signal to the
generator set activating the automatic start system
on the generator.
•
After a short start delay the engine generator will
start and begin supplying the ATS with emergency
power. At this time, the ATS will transfer your
connected distribution panel to the generator powering
up your emergency circuits.
•
Upon return of utility power, the ATS will transfer your
connected distribution panel back to line power and
discontinue the start signal to the generator. After a
short cool down period the generator will stop and
return to the standby mode awaiting the next power
interruption.
•
The WINCO Standby generator uses your
own natural gas or LP fuel system. This provides
you with a long continuous run time and
unlimited run time in the case of natural gas.
PSS12H
Home Standby Systems - 8kW to 15kW
Model
Power Output (60 Hz)
PSS8B
120/240V, 1-Phase, 1.0 p.f.
PSS12H
120/240V, 1-Phase, 1.0 p.f.
PSS15B
120/240V, 1-Phase, 1.0 p.f.
PSS20 - NEW MODEL, CONTACT FACTORY FOR DETAILS
NOTE: (1) Derate 3.5% per 1,000 feet elevation above sea level.
Power Rating – Continuous Standby (1)
L P Gas
Natural Gas
kW
8
12
15
kVA
8.0
12.0
15.0
MLCB
Amps
30
50
60
kW
7.2
10
12
kVA
7.2
10.0
12.0
MLCB
Amps
30
42
50
Why Choose
•
•
vs Other Brands?
•
•
•
•
•
Best overall value in performance and design
Higher level of customer service to assist you
before and after the sale
•
Every unit is performance tested prior to shipping,
•
Performance matched accessories
assuring reliable operation
A 80+ year leader in generator technology
Experienced engineers and service technicians
Superior motor starting for efficient operation
Built with pride by people who care about quality
“Clean” electrical power for computers & sensitive equipment
PSS75LS
Optional Automatic
Transfer Switch
Industrial Packaged Standbys - 27kW to 75kW
Model
Power Output (60 Hz)
PSS27LS
PSS30LS
PSS30LS-4
PSS30LS-17
PSS30LS-18
PSS40LS
PSS40LS-4
PSS40LS-17
PSS40LS-18
PSS50LS
PSS50LS-4
PSS50LS-17
PSS50LS-18
PSS75LS
PSS75LS-4
PSS75LS-17
PSS75LS-18
120/240V,
120/240V,
120/208V,
120/240V,
277/480V,
120/240V,
120/208V,
120/240V,
277/480V,
120/240V,
120/208V,
120/240V,
277/480V,
120/240V,
120/208V,
120/240V,
277/480V,
1-Phase,
1-Phase,
3-Phase,
3-Phase,
3-Phase,
1-Phase,
3-Phase,
3-Phase,
3-Phase,
1-Phase,
3-Phase,
3-Phase,
3-Phase,
1-Phase,
3-Phase,
3-Phase,
3-Phase,
1.0
1.0
0.8
0.8
0.8
1.0
0.8
0.8
0.8
1.0
0.8
0.8
0.8
1.0
0.8
0.8
0.8
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
p.f.
Power Rating - Continuous Standby (1)
L P Gas
Natural Gas
kW
kVA
MLCB
Amps
kW
kVA
MLCB
Amps
27
30
30
30
30
40
40
40
40
50
50
50
50
70
70
70
70
27.0
30.0
38.0
38.0
38.0
40.0
50.0
50.0
50.0
50.0
62.5
62.5
62.5
70.0
87.5
87.5
87.5
110
125
104
90
45
166.6
139
120
60
200
173
150
75
291
243
211
100
24
30
30
30
30
38
38
38
38
45
45
45
45
75
75
75
75
24.0
30.0
38.0
38.0
38.0
38.0
47.5
47.5
47.5
45.0
56.2
56.2
56.2
75.0
93.7
93.7
93.7
100
125
104
90
45
158.3
132
114
57
187
156
135
67
300
250
225
100
NOTE: (1) Derate 3.5% per 1,000 feet elevation above sea level.
•
•
•
•
•
•
•
Full Engine Instrumentation - Water temperature,
oil pressure, battery level
Available with LP Liquid Withdrawal fuel system option
Ammeter, frequency meter and voltmeter standard
Solid state voltage regulation
Overspeed, low oil pressure, high water temperature,
and overcrank protection with indicator lights
Optional Level II engine controls available to meet NFPA 99 &
NFPA 110 requirements with optional remote annunciator panel
Electronic governor standard
Our reputation is built on the fact that you can count on
‘s 80+ years of experience
to provide you with a standby system that performs again and again, year after year. We
believe that every
power product offers the best value in the market today.
Portable Power In A Complete, Compact Package!
Nearly everyone has experienced the inconvenience that a power outage can cause. A standby generator can help
you be prepared for those times.
’s PSS6H portable tri-fuel generator can provide you with power to run everyday equipment, such as lights,
televisions, heating, air conditioning and refrigeration when utility service is temporarily down. This handy portable
power system can keep you and your family comfortable during those untimely power interruptions.
The PSS6H offers the convenience of standby power along with the flexibility of operation on LP Vapor, Natural Gas
or gasoline fuel, and meets EPA certification for emissions standards. Whether at the cabin for the weekend, or
staying at home, backup power is readily available with the PSS6H portable home power generator (7).
Features:
Benefits:
•
•
•
•
•
•
•
•
•
•
•
•
Powerful Honda V-Twin engine
Wheel kit for portability
Fuel shut off solenoid
Float type battery charger
Canvas cover for storage
Manual Service transfer kit, including 12-foot cord with plug
Tri-Fuel Generator
with HONDA OHV engine
operates on LP fuel,
natural gas or gasoline (6)
Move to different locations as the need occurs
Tri-fuel operation allows various fuel options
Battery stays fully charged and ready when needed
Light, compact design allows easy handling
Quick, easy connection to electrical loads
PSS6H ELECTRICAL SPECIFICATIONS
Max/Cont Power Rating (1)
6000/5500 watts
AC Output Voltage (60hz)
120/240V, 1-Ph
Continuous Amp Rating (1)
45.8 amps/22.9 amps
Motor Starting Ability (1, 2)
2 h.p.
Cooling System
Air
Fuel Tank Capacity (gasoline)
4.5 gallons
Low Oil Protection
Standard
ENGINE SPECIFICATIONS
Make/Model
Honda GX340
Displacement/Type
337 cc/OHV
Battery Rack/Cables (3)
Standard
Starting System (4)
Electric/Recoil
FUEL CONSUMPTION (FULL LOAD)
Gasoline Fuel
1.0 gal/hr
LP Gas Fuel (5)
1.1 gal/hr
Natural Gas Fuel
77 ft3/hr
WARRANTY INFORMATION
Engine/Generator (6)(7)
3 yrs/1 yr
SIZE AND WEIGHT
L x W x H (generator only)
30” x 22” x 22”
Total Ship Weight
305 lbs.
PSS6H
Fuel Shut-Off
Solenoid Kit
(installed)
Two Wheel
Dolly Kit
for portability
Included With PSS6H
for a complete system:
Easy starting, optimum running
Manual Service Transfer Kit
Outdoor
enclosure for
cord storage
Protective
Canvas Cover
for storage
Indoor load
center for
selected
emergency
circuits
Battery Charger to
keep start battery
fully charged
12-foot cord with L14-30P plug
for connection to generator
NOTES:
(1) Based on gasoline fuel. Derate 10% for LP gas, 20% for natural gas fuel. (2) Code G capacitor start motor. (3) Start battery
not included. (4) Electric start must be used when starting on vapor fuel. (5) One gallon of L.P. gas equals 4.23 lbs. (6) Engine
warranty applies to retail purchases made after January 1, 2009. (7) Standby use only - prime power or off grid use warranty is 90
Days.
NOTE: Professional installation required - contact your local electrician for assistance in choosing the right generator for
your needs.
225 South Cordova Ave
Le Center MN 56057 USA
PSS 1/09
Telephone: (507) 357-6821
Fax: (507) 357-4857
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
PSS8B
Packaged Standby Generator
FEATURES
• Easily installed outside new or existing homes
• Critical grade exhaust system for quieter operation
• Mainline circuit breaker included standard
• Sound attenuated housing constructed of galvannealed
steel with durable powder paint finish & hinged access doors
• Equipped for either Natural Gas or LP Vapor fuel
• CARB & EPA approved
• UL & CSA approved
• Low maintenance
• Requires purchase of a transfer switch for automatic
operation (sold separately - see specs below)
MODEL
NUMBER
PSS8B
POWER RATING– CONTINUOUS STANDBY (1)
L.P. Gas
Natural Gas
KW KVA AMPS
KW KVA AMPS
8.0
8.0
30.0
7.2
7.2
30.0
POWER
OUTPUT (60hz)
120/240V, 1-Phase, 1.0 p.f.
Starting System
PSS8B4W 4-Wire Start System
Requires purchase of an ASCO165 4-wire start
transfer switch. All starting controls including start
contacts and fuel solenoid contacts as well as all delays
are located on the control board in the ASCO transfer
switch. Cycle cranking is included standard. A Running
Time Meter, Off/Normal & Auto/Run/Start Switches are
provided on the generator control panel.
PSS8B2W 2-Wire Start System
Requires purchase of the optional 2 -wire start control
which makes the unit compatible with any transfer switch
using a dry contact closure upon power failure. Two wire
start controls come standard with a 10 second start delay
and 90 second cooldown delay. Cycle cranking is included
standard. Running Time Meter & Auto/Off/Run Switch are
provided on the generator control panel.
Engine Specifications
Generator Data
Make/Model
Displacement/Type
Engine Speed
B&S Vanguard
480 c.c./OHV
3600 rpm
Engine Features
Electronic Ignition
Cooling System
NG or LP Vapor Fuel System
Critical Grade Exhaust System
DBA Rating @ 7 meters (23 ft)
Battery Rack/Cables (3)
Vibration Isolators
Low Oil Protection
Float Battery Charger
Standard
Air
Standard
Standard
68 N-L/70 F-L
Standard
Standard
Standard
Standard
Fuel Consumption
Full Load - LP Gas (2)
Half Load - LP Gas (2)
Full Load - Natural Gas
Half Load - Natural Gas
Required Fuel Pressure
1.60 gal/hr
1.00 gal/hr
132 ft3/hr
95 ft3/hr
4-6 oz or 7-11” w.c.
Generator Type (4)
Voltage Regulation
Frequency Regulation
Harmonic Distortion
Motor Starting Ability (5)
Size and Weight
L x W x H (in)
Ship Weight (lbs)
30.5 x 27.3 x 27.4
365
Warranty Information
Engine/Generator
2 Years/1 Year
Optional Accessories
Engine Heater
Vapor Fuel Filter
ULATS165 Auto Transfer Switch (sold separately)
Engine Start Delay
Transfer Delay
Retransfer Delay
Engine Cooldown Delay
14-Day Exercise Circuit
Warranty
NOTES:
(1) Derate 3.5% per 1,000 feet elevation above sea level
(2) One gallon of L.P. gas equals 4.23 lbs
(3) Battery not included. Requires 12-volt Group 26, 450 cca battery
(4) Rotating Field Brushless design generator
(5) Code G capacitor start motor
PSS8B 10/08
RFL
+/- 5%
+/- 3%
< 5%
4 hp
3 Seconds
15 Seconds
5 Minutes
1 Minute
Standard
1 Year
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
PSS12H
Packaged Standby Generator
FEATURES
• Easily installed outside new or existing homes
• Critical grade exhaust system for quieter operation
• Mainline circuit breaker included standard
• Sound attenuated housing constructed of galvannealed
steel with durable powder paint finish & hinged access doors
• Equipped for either Natural Gas or LP Vapor fuel
• EPA approved
• Low maintenance
• CSA (Canadian Standards Association) approved
• Requires purchase of a transfer switch for automatic
operation (sold separately - see specs below)
MODEL
NUMBER
PSS12H4W
POWER
OUTPUT (60hz)
120/240V, 1-Phase, 1.0 p.f.
POWER RATING– CONTINUOUS STANDBY (1)
L.P. Gas
Natural Gas
KW KVA AMPS
KW KVA AMPS
12
12.0
50.0
10
10.0
42.0
Starting System
PSS12H4W 4-Wire Start System
Requires purchase of an ASCO165 4-wire start
transfer switch. All starting controls including start
contacts and fuel solenoid contacts as well as all delays
are located on the control board in the ASCO transfer
switch. Cycle cranking is included standard. A Running
Time Meter, Off/Normal & Auto/Run/Start Switches are
provided on the generator control panel.
PSS12H2W 2-Wire Start System
Requires purchase of the optional 2 -wire start control
which makes the unit compatible with any transfer switch
using a dry contact closure upon power failure. Two wire
start controls come standard with a 10 second start delay
and 90 second cooldown delay. Cycle cranking is included
standard. Running Time Meter & Auto/Off/Run Switch are
provided on the generator control panel.
Engine Specifications
Generator Data
Make/Model
Displacement/Type
Engine Speed
Honda GX670
670 c.c./OHV
3600 rpm
Engine Features
Electronic Ignition
Cooling System
NG or LP Vapor Fuel System
Critical Grade Exhaust System
DBA Rating @ 7 meters (23 ft)
Battery Rack/Cables (3)
Vibration Isolators
Low Oil Protection
Float Battery Charger
Standard
Air
Standard
Standard
66 N-L/69 F-L
Standard
Standard
Standard
Standard
Fuel Consumption
Full Load - LP Gas (2)
Half Load - LP Gas (2)
Full Load - Natural Gas
Half Load - Natural Gas
Required Fuel Pressure
2.2 gal/hr
1.39 gal/hr
195 ft3/hr
140 ft3/hr
4-6 oz or 7-11” w.c.
Generator Type (4)
Voltage Regulation
Frequency Regulation
Harmonic Distortion
Motor Starting Ability (5)
Size and Weight
L x W x H (in)
Ship Weight (lbs)
37.9 x 30.8 x 30.9
504
Warranty Information (6)
Engine/Generator
3 Years/1 Year
Optional Accessories
Engine Heater
Vapor Fuel Filter
ULATS165 Auto Transfer Switch (sold separately)
Engine Start Delay
Transfer Delay
Retransfer Delay
Engine Cooldown Delay
14-Day Exercise Circuit
Warranty
NOTES:
(1) Derate 3.5% per 1,000 feet elevation above sea level
(2) One gallon of L.P. gas equals 4.23 lbs
(3) Battery not included. Requires 12-volt Group 26, 450 cca battery
(4) Rotating Field Brushless design generator
(5) Code G capacitor start motor
(6) Engine warranty applies to retail purchases made after January 1, 2009
PSS12H 1/09
RFL
+/- 5%
+/- 3%
< 5%
6 hp
3 Seconds
15 Seconds
5 Minutes
1 Minute
Standard
1 Year
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
PSS15B
Packaged Standby Generator
FEATURES
• Easily installed outside new or existing homes
• Critical grade exhaust system for quieter operation
• Mainline circuit breaker included standard
• Sound attenuated housing constructed of galvannealed
steel with durable powder paint finish & hinged access doors
• Equipped for either Natural Gas or LP Vapor fuel
• CARB & EPA approved
• UL & CSA approved
• Low maintenance
• Requires purchase of a transfer switch for automatic
operation (sold separately - see specs below)
MODEL
NUMBER
PSS15B
POWER RATING– CONTINUOUS STANDBY (1)
L.P. Gas
Natural Gas
KW KVA AMPS
KW KVA AMPS
15
15.0
60.0
12
12.0
50.0
POWER
OUTPUT (60hz)
120/240V, 1-Phase, 1.0 p.f.
Starting System
PSS15B4W 4-Wire Start System
Requires purchase of an ASCO165 4-wire start
transfer switch. All starting controls including start
contacts and fuel solenoid contacts as well as all delays
are located on the control board in the ASCO transfer
switch. Cycle cranking is included standard. A Running
Time Meter, Off/Normal & Auto/Run/Start Switches are
provided on the generator control panel.
PSS15B2W 2-Wire Start System
Requires purchase of the optional 2 -wire start control
which makes the unit compatible with any transfer switch
using a dry contact closure upon power failure. Two wire
start controls come standard with a 10 second start delay
and 90 second cooldown delay. Cycle cranking is included
standard. Running Time Meter & Auto/Off/Run Switch are
provided on the generator control panel.
Engine Specifications
Generator Data
Make/Model
Displacement/Type
Engine Speed
B&S Vanguard
895 c.c./OHV
3600 rpm
Engine Features
Electronic Ignition
Cooling System
NG or LP Vapor Fuel System
Critical Grade Exhaust System
DBA Rating @ 7 meters (23 ft)
Battery Rack/Cables (3)
Vibration Isolators
Low Oil Protection
Float Battery Charger
Standard
Air
Standard
Standard
67 N-L/72.5 F-L
Standard
Standard
Standard
Standard
Fuel Consumption (estimate)
Full Load - LP Gas (2)
Half Load - LP Gas (2)
Full Load - Natural Gas
Half Load - Natural Gas
Required Fuel Pressure
2.96 gal/hr
1.75 gal/hr
260 ft3/hr
170 ft3/hr
4-6 oz or 7-11” w.c.
Generator Type (4)
Voltage Regulation
Frequency Regulation
Harmonic Distortion
Motor Starting Ability (5)
Size and Weight
L x W x H (in)
Ship Weight (lbs)
44.1 x 33.2 x 38.1
725 lbs.
Warranty Information
Engine/Generator
2 Years/1 Year
Optional Accessories
Engine Heater
Vapor Fuel Filter
ULATS165 Auto Transfer Switch (sold separately)
Engine Start Delay
Transfer Delay
Retransfer Delay
Engine Cooldown Delay
14-Day Exercise Circuit
Warranty
NOTES:
(1) Derate 3.5% per 1,000 feet elevation above sea level
(2) One gallon of L.P. gas equals 4.23 lbs
(3) Battery not included. Requires 12-volt Group 26, 450 cca battery
(4) Rotating Field Brushless design generator
(5) Code G capacitor start motor
PSS15B 04/08
RFL
+/- 5%
+/- 3%
< 5%
7.5 hp
3 Seconds
15 Seconds
5 Minutes
1 Minute
Standard
1 Year
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
PSS30LS
PACKAGED STANDBY
GENERATOR
L.P. GAS
MODEL NUMBER
POWER OUTPUT (60hz)
KW
KVA
AMPS
PSS30LS
120/240V, 1-Phase, 1.0 p.f.
30.0
30.0
125
PSS30LS-4
120/208V, 3-Phase, .8 p.f.
30.0
38.0
104
PSS30LS-17
120/240V, 3-Phase, .8 p.f.
30.0
38.0
90
PSS30LS-18
277/480V, 3-Phase, .8 p.f.
30.0
38.0
45
Power Rating – Continuous Standby; Derate 3.5% per 1,000 feet elevation above sea level.
Engine Specifications and Features
The 4 cylinder, overhead valve GM 3.0 engine develops 48 hp
at 1800 rpm with a displacement of 181 cu.in. The engine is
controlled by an electronic governor, maintaining frequency at
60hz +/- .5%. DB rating is 74 dBA at standard 7 meters.
The engine features include electronic ignition, engine
blockheater and a vapor fuel system as standard. A critical
grade muffler is installed to reduce engine noise levels.
Battery rack and cables, and a battery tender (charger) are
also installed in the standard package. A BCI Group 24 650
CCA battery must be purchased separately.
Engine cooling is provided by a unit mount radiator. The
engine is equipped with a belt driven pusher type fan.
Fuel Consumption
LP Gas
Natural Gas
Full Load
3.3 gal/hr
320 ft3/hr
Half Load
2.4 gal/hr
197 ft3/hr
Generator
The generator is a single bearing rotating field generator
mounted to the engine flywheel via dual flex drive discs.
Three phase generators have 12 lead broad range
reconnectable stators; single phase stators are 4 lead. An
external voltage regulator maintains proper voltage output,
accurate to +/- 1.5%. The generator features Class H
insulation with harmonic distortion of less than 5% at full
load.
Telephone interference; The THF (as defined by BS4999
Part 40) is better than 2%. The TIF (as defined by ASA
C50.12) is better than 50.
NATURAL GAS
KW
KVA
AMPS
30.0
30.0
125
30.0
38.0
104
30.0
38.0
90
30.0
38.0
45
Engine/Generator Control System
* Solid state digital control with LCD display
* Run-Off-Auto function is controlled by three push buttons
with indicator lights
* LCD Displays: Engine Oil Pressure, Coolant Temperature,
Battery Voltage Level and Frequency continuously, with the
ability to toggle the voltage and amperage on each phase.
* Three additional Indicator Lamps notify the user when the
system is Not-In-Auto, in Alarm condition, or when the
generator is supplying over 2% of its capacity to the loads.
.
Digital Engine Control Standard Set Up:
* Start Delay
10 seconds
* Cool Down Delay
5 minutes
* Cycle Cranking
3 cycles
* Overcrank Protection
Standard
* Overspeed Protection
Standard
* Low Oil Pressure Protection
Standard
* High Water Temperature Protection
Standard
Options:
* NFPA 99 and NFPA 110 compatible Digital Controls available with pre-alarms.
* Remote displays with 7 pre-alarms and 8 alarm indicators,
switch off auto and unit supplying load lamps.
* Vapor fuel strainer.
* LPG liquid withdrawal fuel system.
* Optional automatic transfer switch sold separately. Contact
factory for sizes and types available.
Warranty Information
Generator
Engine
2 yrs or 1000 hrs
1 yr or 2000 hrs
The engine generator combination has the ability to start
and operate motors up to 12 hp Code G. Mainline circuit
breaker included for generator protection.
Size and Weight
L x W x H (in.)
Ship Weight (lbs.)
7/09
94 x 35 x 48.5
1650 lbs.
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
PSS40LS
PACKAGED STANDBY
GENERATOR
L.P. GAS
MODEL NUMBER
POWER OUTPUT (60hz)
KW
KVA
AMPS
PSS40LS
120/240V, 1-Phase, 1.0 p.f.
40.0
40.0
167
PSS40LS-4
120/208V, 3-Phase, .8 p.f.
40.0
50.0
139
PSS40LS-17
120/240V, 3-Phase, .8 p.f.
40.0
50.0
120
PSS40LS-18
277/480V, 3-Phase, .8 p.f.
40.0
50.0
60
Power Rating – Continuous Standby; Derate 3.5% per 1,000 feet elevation above sea level.
Engine Specifications and Features
The 6 cylinder, overhead valve GM 4.3 engine develops 68 hp
at 1800 rpm with a displacement of 262 cu.in. The engine is
controlled by an electronic governor, maintaining frequency at
60hz +/- .5%. DB rating is 74 dBA at standard 7 meters.
The engine features include electronic ignition, engine
blockheater and a vapor fuel system as standard. A critical
grade muffler is installed to reduce engine noise levels.
Battery rack and cables, and a battery tender (charger) are
also installed in the standard package. A BCI Group 24 650
CCA battery must be purchased separately.
Engine cooling is provided by a unit mounted radiator. The
engine is equipped with a belt driven pusher type fan.
Fuel Consumption
LP Gas
Natural Gas
Full Load
4.7 gal/hr
450 ft3/hr
Half Load
4.1 gal/hr
332 ft3/hr
Generator
The generator is a single bearing rotating field generator
mounted to the engine flywheel via dual flex drive discs.
Three phase generators have 12 lead broad range
reconnectable stators; single phase stators are 4 lead. An
external voltage regulator maintains proper voltage output,
accurate to +/- 1.5%. The generator features Class H
insulation with harmonic distortion of less than 5% at full
load.
Telephone interference; The THF (as defined by BS4999
Part 40) is better than 2%. The TIF (as defined by ASA
C50.12) is better than 50.
NATURAL GAS
KW
KVA
AMPS
38.0
38.0
158
38.0
47.5
132
38.0
47.5
114
38.0
47.5
57
Engine/Generator Control System
* Solid state digital control with LCD display
* Run-Off-Auto function is controlled by three push buttons
with indicator lights
* LCD Displays: Engine Oil Pressure, Coolant Temperature,
Battery Voltage Level and Frequency continuously, with the
ability to toggle the voltage and amperage on each phase.
* Three additional Indicator Lamps notify the user when the
system is Not-In-Auto, in Alarm condition, or when the
generator is supplying over 2% of its capacity to the loads.
.
Digital Engine Control Standard Set Up:
* Start Delay
10 seconds
* Cool Down Delay
5 minutes
* Cycle Cranking
3 cycles
* Overcrank Protection
Standard
* Overspeed Protection
Standard
* Low Oil Pressure Protection
Standard
* High Water Temperature Protection
Standard
Options:
* NFPA 99 and NFPA 110 compatible Digital Controls available with pre-alarms.
* Remote displays with 7 pre-alarms and 8 alarm indicators,
switch off auto and unit supplying load lamps.
* Vapor fuel strainer.
* LPG liquid withdrawal fuel system.
* Optional automatic transfer switch sold separately. Contact
factory for sizes and types available.
Warranty Information
Generator
Engine
2 yrs or 1000 hrs
1 yr or 2000 hrs
The engine generator combination has the ability to start
and operate motors up to 17.5 hp Code G. Mainline circuit
breaker included for generator protection.
Size and Weight
L x W x H (in.)
Ship Weight (lbs.)
4/08
93.5 x 35 x 48.5
1920 lbs.
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
PSS50LS
PACKAGED STANDBY
GENERATOR
L.P. GAS
MODEL NUMBER
POWER OUTPUT (60hz)
KW
KVA
AMPS
PSS50LS
120/240V, 1-Phase, 1.0 p.f.
50.0
50.0
200
PSS50LS-4
120/208V, 3-Phase, .8 p.f.
50.0
62.5
173
PSS50LS-17
120/240V, 3-Phase, .8 p.f.
50.0
62.5
150
PSS50LS-18
277/480V, 3-Phase, .8 p.f.
50.0
62.5
75
Power Rating - Continuous Standby; Derate 3.5% per 1,000 feet elevation above sea level.
Engine Specifications and Features
The 8 cylinder, overhead valve GM 5.7L engine develops 102
hp at 1800 rpm with a displacement of 350 cu.in. The engine
is controlled by an electronic governor, maintaining frequency
at 60hz +/- .5%. DB rating is 74 dBA at standard 7 meters.
The engine features include electronic ignition, engine
blockheater and a vapor fuel system as standard. A critical
grade muffler is installed to reduce engine noise levels.
Battery rack and cables, and a battery tender (charger) are
also installed in the standard package. A BCI Group 24 650
CCA battery must be purchased separately.
Engine cooling is provided by a unit mount radiator. The
engine is equipped with a belt driven pusher type fan.
Fuel Consumption
LP Gas
Natural Gas
Full Load
10 gal/hr
725 ft3/hr
Half Load
6.5 gal/hr
500 ft3/hr
Generator
The generator is a single bearing rotating field generator
mounted to the engine flywheel via dual flex drive discs.
Three phase generators have 12 lead broad range
reconnectable stators; single phase stators are 4 lead. An
external voltage regulator maintains proper voltage output,
accurate to +/- 1.5%. The generator features Class H
insulation with harmonic distortion of less than 5% at full
load.
Telephone interference; The THF (as defined by BS4999
Part 40) is better than 2%. The TIF (as defined by ASA
C50.12) is better than 50.
KW
45.0
45.0
45.0
45.0
NATURAL GAS
KVA
AMPS
45.0
187
56.2
156
56.2
135
56.2
67.5
Engine/Generator Control System
* Solid state digital control with LCD display
* Run-Off-Auto function is controlled by three push buttons
with indicator lights
* LCD Displays: Engine Oil Pressure, Coolant Temperature,
Battery Voltage Level and Frequency continuously, with the
ability to toggle the voltage and amperage on each phase.
* Three additional Indicator Lamps notify the user when the
system is Not-In-Auto, in Alarm condition, or when the
generator is supplying over 2% of its capacity to the loads.
.
Digital Engine Control Standard Set Up:
* Start Delay
10 seconds
* Cool Down Delay
5 minutes
* Cycle Cranking
3 cycles
* Overcrank Protection
Standard
* Overspeed Protection
Standard
* Low Oil Pressure Protection
Standard
* High Water Temperature Protection
Standard
Options:
* NFPA 99 and NFPA 110 compatible Digital Controls available with pre-alarms.
* Remote displays with 7 pre-alarms and 8 alarm indicators,
switch off auto and unit supplying load lamps.
* Vapor fuel strainer.
* LPG liquid withdrawal fuel system.
* Optional automatic transfer switch sold separately. Contact
factory for sizes and types available.
Warranty Information
Generator
Engine
2 yrs or 1000 hrs
1 yr or 2000 hrs
The engine generator combination has the ability to start
and operate motors up to 23 hp Code G. Mainline circuit
breaker included for generator protection.
Size and Weight
L x W x H (in.)
Ship Weight (lbs.)
4/08
99.5 x 40 x 49
2533 lbs.
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
PSS75LS
PACKAGED STANDBY
GENERATOR
L.P. GAS
MODEL NUMBER
POWER OUTPUT (60hz)
KW
KVA
AMPS
PSS75LS
120/240V, 1-Phase, 1.0 p.f.
70.0
70.0
291
PSS75LS-4
120/208V, 3-Phase, .8 p.f.
70.0
87.5
243
PSS75LS-17
120/240V, 3-Phase, .8 p.f.
70.0
87.5
211
PSS75LS-18
277/480V, 3-Phase, .8 p.f.
70.0
87.5
100
Power Rating – Continuous Standby; Derate 3.5% per 1,000 feet elevation above sea level.
Engine Specifications and Features
The 8 cylinder, overhead valve GM 5.7L turbocharged engine
develops 130 hp at 1800 rpm with a displacement of 350
cu.in. The engine is controlled by an electronic governor,
maintaining frequency at 60hz +/- .5%. DB rating is 74.2 dBA
at standard 7 meters.
The engine features include electronic ignition, engine
blockheater and a vapor fuel system as standard. A critical
grade muffler is installed to reduce engine noise levels.
Battery rack and cables, and a battery tender (charger) are
also installed in the standard package. A BCI Group 24 650
CCA battery must be purchased separately.
Engine cooling is provided by a unit mount radiator. The
engine is equipped with a belt driven pusher type fan.
Fuel Consumption
LP Gas
Natural Gas
Full Load
12.2 gal/hr
1000 ft3/hr
Half Load
9.1 gal/hr
820 ft3/hr
Generator
The generator is a single bearing rotating field generator
mounted to the engine flywheel via dual flex drive discs.
Three phase generators have 12 lead broad range
reconnectable stators; single phase stators are 4 lead. An
external voltage regulator maintains proper voltage output,
accurate to +/- 1.5%. The generator features Class H
insulation with harmonic distortion of less than 5% at full
load.
Telephone interference; The THF (as defined by BS4999
Part 40) is better than 2%. The TIF (as defined by ASA
C50.12) is better than 50.
NATURAL GAS
KW
KVA
AMPS
75.0
75.0
300
75.0
93.7
250
75.0
93.7
225
75.0
93.7
100
Engine/Generator Control System
* Solid state digital control with LCD display
* Run-Off-Auto function is controlled by three push buttons
with indicator lights
* LCD Displays: Engine Oil Pressure, Coolant Temperature,
Battery Voltage Level and Frequency continuously, with the
ability to toggle the voltage and amperage on each phase.
* Three additional Indicator Lamps notify the user when the
system is Not-In-Auto, in Alarm condition, or when the
generator is supplying over 2% of its capacity to the loads.
Digital Engine Control Standard Set Up:
* Start Delay
* Cool Down Delay
* Cycle Cranking
* Overcrank Protection
* Overspeed Protection
* Low Oil Pressure Protection
* High Water Temperature Protection
10 seconds
5 minutes
3 cycles
Standard
Standard
Standard
Standard
Options:
* NFPA 99 and NFPA 110 compatible Digital Controls available with pre-alarms.
* Remote displays with 7 pre-alarms and 8 alarm indicators,
switch off auto and unit supplying load lamps.
* Vapor fuel strainer.
* LPG liquid withdrawal fuel system.
* Optional automatic transfer switch sold separately. Contact
factory for sizes and types available.
Warranty Information
Generator
Engine
2 yrs or 1000 hrs
1 yr or 2000 hrs
The engine generator combination has the ability to start
and operate motors up to 30 hp Code G. Mainline circuit
breaker included for generator protection.
Size and Weight
L x W x H (in.)
Ship Weight (lbs.)
4/08
99.5 x 40 x 52
2596 lbs.
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
Residential/Light Commercial
Automatic Transfer Switches
Product Features
•
•
•
•
•
•
•
Nominal voltage 120/240 V 60 Hz, single phase.
Listed to UL1008 Transfer Switch Equipment and CSA Certified to CSA 22.2 No. 178-1978 Automatic
Transfer Switches.
Meets National Electrical Code (NEC) and National Fire Protection Association (NFPA) requirements.
True double-throw contacts (no intentional off position), with inherent mechanical interlocking to
prevent connection of generator and utility source.
Convenient terminals to connect neutral and ground conductors from service and load feeders.
Available in Type 1 (indoor) and Type 3R (outdoor) enclosures.
Available from stock.
Time Delay Functions
•
•
•
•
•
3-second time delay to override momentary utility source.
15-second transfer to emergency time delay to allow engine generator to stabilize after starting.
15-second time delay after transfer to the standby source to ignore momentary voltage dips on the generator
during initial loading.
5-minute time delay on retransfer to allow utility source to stabilize prior to transferring the load back to utility
1-minute unloading running time delay for engine generator cool-down before shutdown.
Control Panel
User-friendly control panel with
easy to understand symbols
and all the necessary visual
indicators to inform the operator
of transfer switch and power
source status.
Diagnostic Indicators
The 165 Automatic Transfer Switch has a unique built-in automatic digital diagnostic monitoring system, which
provides status on potential system problems such as: generator failed to start; generator over frequency;
transfer switch did not transfer; and more. It’s one more way you can count on ASCO to provide continuous
power protection ...anytime.
Series 300 Automatic Transfer Switch
The ASCO Microprocessor Controller is used with all sizes of Power
Transfer Switches. It represents the most reliable microprocessor
controller in the industry and includes, as standard, all of the voltage,
frequency, control, timing and connectivity functions required for most
emergency and standby power applications.
The easy-to-read flush-mounted
control and display panel
provides LED indicators for
switch position and source
availability. It also includes test
and time-delay bypass
Electrical Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
600 volt spacing per UL and CSA standards.
Interfacing relays are industrial grade, plug-in type
with dust covers.
Meets or exceeds the requirements for
Electromagnetic Compatibility (EMC).
ANSI C37.90A/IEEE472 Voltage Surge Test
NEMA ICS-109.21 Impulse Withstand Test
Digital circuitry isolated from line voltages
IEC 801-2 Electrostatic discharge (ESD) immunity
ENV50140 and IEC 803-1: Radiated electromagnetic
field immunity
IEC 801-4 Electrical fast transient (EFT) immunity
ENV50142 Surge transient immunity
ENV50141: Conducted radio-frequency field
immunity
EN55011: Group 1, Class A conducted and radiated
emissions
Optically isolated RS-485 Serial Port
EN61000- 4-11 voltage dips and interruptions
immunity.
Standard Selectable Features
•
•
•
•
•
Inphase monitor to transfer motor loads, without
any intentional off time to prevent motor inrush
currents from exceeding normal starting levels.
Engine exerciser to automatically test backup
generator each week. Includes control switch for
testing with or without load.
Selective load disconnect, double-throw contact to
operate at an adjustable 0 to 20 second time delay
prior to transfer and reset 0 to 20 seconds after
transfer.
60 Hz or 50 Hz selector switch.
Three-phase/single-phase selector switch.
Voltage & Frequency Sensing
•
•
•
Adjustable three-phase, close differential
voltage sensing on normal source.
Normal source pickup voltage is adjustable to
95% of nominal; drop-out is adjustable from 70
to 90% of nominal.
Frequency sensing on emergency source.
Pickup at 95% and dropout at 85% of nominal.
Time Delays
•
•
•
•
•
Adjustable time delay to override momentary
normal source outages to delay all transfer
switch and engine-starting signals.
Transfer to emergency time delay. Adjustable
from 0 to 5 minutes for controlled timing of load
transfer to emergency.
Retransfer to normal time delay. Adjustable to
30 minutes.
Five-minute unloaded running time delay for
emergency engine generator cool down.
Four-second time delay to override momentary
to ignore momentary voltage and frequency
transients during initial genset loading.
Optional Accessories
Accessory 11BG
A programmable engine exerciser that provides for weekly or biweekly operation,
includes one form C contact for source availability of normal and emergency (contact
rating 2 amps @ 30VDC, 0.5 amp. @ 125 VAC resistive). The programmable engine
exerciser incorporates a 7 day or 14 day time base with a digital readout display.
Includes "with or without" load control switch for exerciser period.
Accessory 14AA/BA (not pictured)
Auxiliary contacts to indicate position of main contacts. Two (2) for normal and two (2)
for emergency position (one set is standard).
Accessory 44A (not pictured)
Strip Heater with thermostat for extremely cold areas to prevent condensation and
freezing of this condensation. External 120 volt power source required.
Accessory 44G
Strip Heater with thermostat, wired to load terminals: 208-240, 360-380, 460-480, 550600 volts. Contains wiring harnesses for all transfer switch sizes.
Accessory 72A
Serial Module 5110 (RS-485) is used to allow local or remote communications with
ASCO PowerQuest® or SITEWEBTM communications products. (See Remote Monitoring
Section)
Accessory 72E
Connectivity Module 5150 is used to bring several different serial devices that
communicate at different baud rates and with different protocols to a common Ethernet
media.
Accessory 123
A protective window that includes a polycarbonate frame and weather gasket to provide
secure access to the membrane interface for the Type 1 Enclosures. This lockable
cover is an alternative to
ASCO Pulsar® 450 High-Performance Surge Suppressor
The ASCO Pulsar® 450 provides unparalleled protection from power surges and
transients. It is a high-performance surge suppressor which limits large surges and
transients through a unique array of computer-matched metal oxide varistors (MOVs).
Accessory 62W Audible Alarm with Silence Feature
For City of Chicago Code Requirement - audible alarm with silencing feature
to signal each time transfer to emergency occurs. Keyed test switch/retransfer
delay bypass, momentary in both directions. Keyed test switch maintained
transfer to emergency. Includes feature 9C, signal light (PL3 - Green)
indicates normal source available, and 9D, signal light (PL4 - Red) indicates
emergency source available.
GE Digital Energy
Power Quality
ZTX
Automatic Transfer Switch
GE Zenith’s ZTX Series Automatic Transfer Switches are
designed for residential and light commercial critical/
non-life safety applications requiring the dependability
and ease of operation found in a power contactor switch.
• Ratings 40 to 400 amps (2, 3 and 4 pole)
ZTX Series Residential & Light Commercial Switch
with LED Control Panel (cover removed)
• UL 1008, CSA and IEC listed to 480 VAC 50/60Hz
• Seismic Compliance to IEEE-693-2005 and IBC-2003
• Double throw, mechanically interlocked
contactor mechanism
The unit is available in open type, NEMA 1 or NEMA 3R
enclosures. The MX60 control adds a user interface
and functionality, including:
• Electrically operated, mechanically held
• Indicating LEDs for source availability and switch position
• Designed for standby applications
• Pushbuttons for test, exerciser set, timer bypass
and program cancel
GE Zenith’s ZTX switches are equipped with the MX60
control panel. This microprocessor control includes:
• Undervoltage sensing (90% pickup/80% dropout)
of Source 1 (normal)
• Special status annunciation of in-phase transfer
and timer operation
• Selectable 7, 14, 21 or 28 day (factory set 28 days)
generator (Source 2) with or without load exerciser timer
• Voltage and frequency sensing of Source 2 (emergency)
(90% voltage/95% frequency pickup)
• Diagnostic LED indications in logical one-line configuration
• Time Delay Engine Start (P) - 5 seconds
Additional options include:
• Time Delay Engine Warmup (W) - Transfer to
Emergency (Source 2) - 20 seconds
• Time Delay Utility Stabilization/Retransfer to
Utility (Source 1) (T) - 5 minutes
A3/A4 Auxiliary contacts (1 each) closed in Source 1
(normal) and Source 2 (emergency) positions
B9X
1.5 Amp/12 or 24 VDC Battery Charger
• Time Delay Engine Cool Down (U) - 5 minutes
All time delays are fixed (non-adjustable).
MX60 Microprocessor Control Panel
Ordering Information
Z T X 0 0 0
0
MODEL/TYPE
Z
T
X
Z E C
AMPERE SIZE SWITCHED
POLES
CONTROL
PANEL
APPLICATION
M 6
0
0 0 4
MX60
Microprocessor
Control Unit
Utility - Generator
M 0 6 0
Z V C
ENCLOSURE TYPE
OPERATIONAL VOLTAGE
B
0 1
A B
40 amps
2 Poles
Type 1 Enclosure
Consult Table Below
0 0 8
E
3 R
0 0
80 amps
3 Poles
Type 3R Enclosure
No Microprocessor
Control Unit
0 1 0
F
0 0
100 amps
4 Poles
Open Style Unit
0 0 0
Standard (Open Transition)
ACCESSORIES
Then choose additional
accessories
A3/A4
Auxiliary Contacts (1 each)
Closed in Source 1 (normal)
and Source 2 (emergency)
B9X
Battery Charger
1.5 Amp / 12 or 24 VDC
0 1 5
150 amps
Example
0 2 0
0 2 2
200 amps
225 amps
0 3 0
0 4 0
300 amps
400 amps
ZTX000M60010E-ZEC01ZVC50M060
This number string shows the correct format
for a ZTX Model Automatic Transfer Switch
with MX60 microprocessor control unit,
Utility - Generator, 100 amps, 3 pole,
NEMA Type 1 enclosure, 480V 3φ, 3 wire,
60 Hz system with the standard group
of accessories.
Technical Specifications
Lug Configuration
Amp Size
Qty Per Phase
and Neutral
40 - 80
1
#8 to 3/0
8 to 85 mm2
100 - 225
1
#6 to 250 MCM
13 to 127 mm2
300 - 400
1
#4 to 600 MCM
21 to 304 mm2
Size
Dimensions inches (mm)
Ampere
Poles
Rating
40 - 225
2, 3
4
300 - 400
2, 3
4
NEMA 1
H
24
(610)
W
Weight lbs. (kg)
NEMA 3R
D
H
18
10
24
(457) (254) (610)
W
D
18.5 10.5
(470) (267)
46
24
14
46
24
15
(1168) (610) (356) (1168) (610) (381)
Open
Style
NEMA 1
12 (5.4)
67 (30.4)
18 (8.2)
73 (33.1)
59 (26.8) 168 (76.2)
70 (31.8) 180 (81.7)
UL 1008 Withstand and Closing Ratings
For information
on ZTX OEM
plans, please
consult your GE
representative
A
B
Voltage Phase
1
2
2
3
3
3
3
4
4
4
5
5
5
5
5
5
6
7
7
7
7
8
9
9
9
9
9
0
0
2
0
1
2
5
0
1
2
0
1
2
5
7
8
3
0
1
4
5
2
0
1
2
3
7
120
120/240
110/220
240
208
220
139/240
120/208
127/220
127/220
480
440
440
460
480
254/440
575
277/480
277
266/460
460
380
240/416
220/380
220/380
240/416
380
1
1
1
3
3
3
3
3
3
3
3
3
3
1
1
3
1
3
1
3
3
1
3
3
3
3
3
Config.
Hz
2 wire
3 wire
3 wire
3 wire
3 wire
3 wire
4 wire
4 wire
4 wire
4 wire
3 wire
3 wire
3 wire
3 wire
2 wire
4 wire
2 wire
4 wire
2 wire
4 wire
3 wire
2 wire
4 wire
4 wire
4 wire
4 wire
3 wire
60
60
50
60
60
50
60
60
60
50
60
60
50
50
60
60
60
60
60
60
60
50
60
60
50
50
60
Note: Operating voltage must be specified at time of order.
Only the most common voltages are shown above.
Please refer to GE Zenith Controls Bulletin TB-1102.
GE Digital Energy – Power Quality
701 E 22nd Street, Lombard, IL 60148 USA
800 637 1738 www.gedigitalenergy.com/ats
Information subject to change without notice. Please verify all details with GE.
© 2008 General Electric Company All Rights Reserved
PB-1601 (8/08)
Why Winco PTOS?
♦ Winco PTO Generators-Quality & Innovation since 1927
♦ PTO Generators come standard with:
o Color coded voltmeter for PTO/RPM viewable from
tractor.
o Full power plug which allows the full rated output from a
single outlet up to 416 Amps (240V)
o Protective rodent screens
o Lifting eye
♦ Insulation class F, double dip varnished.
♦ Continuous duty ratings at 104° F (40° C)
♦ Watertight, pre-lubricated bearings
♦ High quality generator ends, built to last
♦ 100% copper windings assure longer life expectancy
♦ Superior motor starting capabilities for larger motors
♦ Helical gear drive
♦ Industrial powder coat paint on all units.
♦ Circuit breaker protection, 1 main & 2 secondary
♦ 100% of generators are load tested, not statistically sampled as
some manufacturers do
♦ Service and parts distributors available nationwide
♦ 15-50KW 540 X 6 spline input
♦ 50-75KW 1000 RPM gearcase with 6 spline input.
♦ 85-150KW 1000 RPM gearcase with heavy duty 1¾” 20 spline
input
♦ Optional Accessories
o Heavy duty trailers for all models
o 15KW three point hitch kits
o 25-50KW 1000 RPM gearcase with 6 spline input
o Tumbling bars to meet most tractor shaft configurations
o Square D 100 & 200 amp manual transfer switches
TRACTOR DRIVEN
POWER TAKE-OFF
GENERATORS
SINGLE AND THREE PHASE
540 AND 1000 RPM
15KW - 150KW
FULL RANGE PTO GENERATOR LINE
FOR TODAY’S DIVERSE MARKETS!
Responding to the growing need for tractor-driven
generators of all sizes, WINCO has added numerous
new models to its product offering in PTO generators.
Since 1927, WINCO has been providing solutions to power problems
by offering a line of electrical generator products. Today, WINCO
offers PTO Generators in sizes ranging from 15kW through 150kW,
with either 540 or 1000 rpm gear cases available on most models. This
extensive offering will meet our customers’ individual requirements,
from the hobby farmer to the large livestock producer.
The perfect accessory for your compact tractor.
WINCO’s PTO series is designed to provide reliable
electrical power for customers who already have a
compact utility tractor with sufficient pto horsepower.
The PTO generator is a cost effective way of providing
120/240 volt single phase standby power when utilty
power is disrupted, inaccessible or impractical.
STANDARD FEATURES
SINGLE PHASE GENERATORS
SPECIFICATIONS
Power Rating (Watts) (1)
A C Output Voltage
Amps (Continuous) (2)
Generator Speed (RPM)
Phase
Receptacles
NEMA 5-20R 120V Duplex
NEMA 14-60R 120/240V
Tractor HP Recommended (4)
PTO Input Speed (RPM)
Code G Motor Starting (3)
Generator Type (10)
Dimensions (LxWxH)
Ship Weight (lbs)
Warranty
* Brushless two pole generator utilizes compound excitation
* Low harmonic content (< 8%) is safe for sensitive loads
* Capacitive excitation for close regulation and high motor
starting capability
* Large, magnetically shielded voltmeter is easily viewed from
tractor seat allowing easy setting of speed
* Rugged cast iron gear case with 540 RPM 1-3/8” six spline
input shaft
* Compact for easy storage
W15PTOS
15 kW
120/240 volts
60 amps
3600
1
1-20 amp
1-60 amp
30
540
8
RFL(C)
33 x 19 x 20
292
1 Year
STANDARD FEATURES
* Mainline circuit breakers
* 100% copper windings
* PTO safety shield
* Single point lifting eye
* Protective rodent screen
* Color coded voltmeter for PTO/rpm
adjustment and to verify proper operation
* 3 year limited warranty
SPECIFICATIONS
Power Rating (Watts) (1)
A C Output Voltage
Amps (Continuous) (2)
Generator Speed (RPM)
Receptacles
NEMA 5-20R 120V Duplex
NEMA 6-50R 240V
Full Power Receptacle/Plug
Tractor HP Recommended (4)
PTO Input Speed (RPM)
Code G Motor Starting (3)
Generator Type (10)
Dimensions (LxWxH)
Ship Weight (lbs)
Warranty
25PTOC-3
25 kW
120/240 volts
104 amps
3600
35PTOC-3
35 kW
120/240 volts
146 amps
1800
50PTOC-3
50 kW
120/240 volts
208 amps
1800
1-20 amp
1-50 amp
Yes
50
540/1000 optional
10
RAB
29 x 16 x 20
330
3 Years
1-20 amp
1-50 amp
Yes
70
540/1000 optional
20
RFB
39 x 20 x 21
536
3 Years
1-20 amp
1-50 amp
Yes
100
540/1000 optional
25
RFB
39 x 20 x 21
612
3 Years
SINGLE PHASE
GENERATORS
SPECIFICATIONS
W85FPTOS
W100FPTOS
W150FPTOS
Power Rating (Watts) (1)
A C Output Voltage
Amps (Continuous) (2)
Generator Speed (RPM)
Phase
Receptacles
Tractor HP Recommended (4)
PTO Input Speed (RPM)
Code G Motor Starting (3)
Generator Type (10)
Dimensions (LxWxH)
Ship Weight (lbs)
Warranty
85 kW
120/240 volts
354 amps
1800
1
Yes (6, 8)
170
1000
45
RFL(X)
49 x 17 x 27
1080
3 Years
100 kW
120/240 volts
416 amps
1800
1
Yes (6, 8)
200
1000
55
RFL(X)
47 x 21 x 30
1275
3 Years
150 kW
120/240 volts
625 amps
1800
1
Yes (6)
290
1000
75
RFL (X)
47 x 27 x 30
1620
3 Years
STANDARD FEATURES
*
*
*
*
*
Heavy duty construction
100% copper windings
Superior motor starting
Operates at 1800 rpm
Precision-AVR regulated voltage 2% on RFL(X) types
*
*
*
*
*
*
Full load connector-350A & below
Convenience receptacles
Mainline circuit breaker
Grounding terminal
Lifting eye and Mounting base
Sealed ball bearings
*
*
*
*
Helical gears
Rodent Screen
Shielded PTO shaft
Speed indicator visible from
tractor seat
* Three year limited warranty
THREE PHASE
GENERATORS
SPECIFICATIONS
Power Rating (Watts) (1)
A C Output Voltage
Amps (Continuous) (2)
Generator Speed (RPM)
Phase
Receptacles
Tractor HP Recommended (4)
PTO Input Speed (RPM)
Code G Motor Starting (3)
Generator Type (10)
Dimensions (LxWxH)
Ship Weight (lbs)
Warranty
40PTOC-4/
45PTOC-17
40/45 kW
120/208
or 120/240
111/108
1800
3
Yes (6, 8)
90
540 (1000 opt)
25
RFB
38 x 23 x 20
558
3 Years
NOTES:
1) Continuous rating per NEMA MGI-22.40 standards
2) Unity (1.0) power factor
3) NEMA Code G capacitor start motor
4) For full rated output. Each 2 hp of tractor power
equals approximately 1 kW of electric power output
6) NEMA 5-20R, NEMA 6-50R receptacles
7) NEMA 5-20R, NEMA 14-60R receptacles
75FPTOC-4/
75FPTOC-17
75 kW
120/208
or 120/240
208/180
1800
3
Yes (6, 8)
150
1000
40
RFB
44 x 23 x 20
738
3 Years
W105FPTOT
W145FPTOT
105 kW
120/208, 120/240
or 277/480
291/253/126
1800
3
Yes (6, 8, 9)
210
1000
40
RFL(X)
47 x 21 x 30
1234
3 Years
145 kW
120/208, 120/240
or 277/480
402/349/174
1800
3
Yes (6, 9)
290
1000
70
RFL(X)
47 x 27 x 30
1540
3 Years
8) Full load connector and plug provided
9) 480 volt machines have no convenience receptacles or full load
connector, connections to circuit breaker only
10) RFL(C) is Rotating Field Brushless, capacitor excitation; RFL(X)
is Rotating Field Brushless, external regulation; RAB is Rotating
Armature Brush Type; RFB is Rotating Field Brush Type
11) Specifications Subject To Change Without Notice
PERFORMANCE MATCHED ACCESSORIES
Three-point Hitch, includes PTO shaft
(for model W15PTOS)
Double Throw Manual
Transfer Switches
Off-road Trailers
Spline Adapter (Use with 25PTOC-3)
(1-1/8” i.d. - 1-3/8” 6 spline)
* General Duty
* Non-Fusible
* Double Throw
* Nema 3R Outdoor
* Available in 100 and
200 amp, single or
three phase voltages.
Tumbling Bar Specifications
WARNING:
An approved manual transfer switch
must be used to connect your PTO
generator to your electrical system.
Without an approved manual transfer
switch, power can flow from the PTO
generator into the power lines, causing
fatal electric shock to repair crews
working on the power lines. Consult an
electric power company representative
and a licensed electrician for the proper
installation procedures.
PTO 8/09
Generator PTO
Operating Generator End
Tractor End
Power Rating
Speed
Connection
Connection
15 kW
540 rpm 1-3/8”-6 spline
1-3/8”-6 spline
25 kW
540 rpm 1-1/8”-keyed
1-3/8”-6 spline
35, 40, 45 & 50 kW
540 rpm 1-3/8”-6 spline
1-3/8”-6 spline
25 - 75 kW
1000 rpm 1-3/8”-6 spline
1-3/8”-21 spline
85 kW (Option 1)
1000 rpm 1-3/4”-20 spline 1-3/4”-20 spline
85 kW (Option 2)
1000 rpm 1-3/4”-20 spline 1-3/8”-21 spline
100 & 105 kW (Option 1) 1000 rpm 1-3/4”-20 spline 1-3/4”-20 spline
100 & 105 kW (Option 2) 1000 rpm 1-3/4”-20 spline 1-3/8”-21 spline
145 & 150 kW
1000 rpm 1-3/4”-20 spline 1-3/4”-20 spline
(Note: 25 kW has keyed end - requires spline adapter)
Shaft
Power
Rating
43 hp
50 hp
90 hp
135 hp
167 hp
167 hp
167 hp
167 hp
257 hp
225 South Cordova Avenue, Le Center MN 56057
507-357-6821 Fax: 507-357-4857
Sales: 800-733-2112 Service: 507-357-6831
E-Mail: [email protected]
Web Site: www.wincogen.com
TWO BEARING
GENERATORS
2FSM2PC-1
8KS2GC-3
Industrial designed, rugged, two bearing generator. Double baked armatures, oversize diode
and double sealed permanent bearings, all combine to insure maximum performance and
life. Units are designed to rotate either direction without changing the wiring, and are rated at
unity power factor. Units require approximately 2 HP input for each 1000 watts output from
the generator. Each unit is factory tested to insure its performance and reliability.
MODEL NUMBER
WATTS
RATED AC AMPS
VOLTS @ 60 HZ
OPERATING SPEED
MOTOR STARTING CAPABILITY
RECEPTACLES:
120V NEMA 5-15R
240V NEMA 6-15R
240V NEMA 6-50R
AC VOLTMETER
LENGTH
WIDTH
HEIGHT
SHAFT DIAMETER
WEIGHT
WARRANTY
2FSM2PC-1
2000
16.7
120
3600 rpm
1/2 hp
8KS2GC-3
8000
66.6/33.3
120/240
3600 rpm
3 hp
2-15 amp
N/A
N/A
N/A
15 in.
6.5 in.
6.75 in.
5/8 in.
56 lbs.
1 year
2-15 amp
2-15 amp
1-50 amp
Standard
19 in.
12 in.
17.75 in.
1-1/4 in.
175 lbs.
1 year
A Tradition Since 1927
BRUSHLESS
TWO BEARING
GENERATORS
TB6000C
TB72000GFI
WINCO’s TB Series Two Bearing Generators incorporate a rugged yet lightweight, brushless design.
Epoxy baked rotors, oversized diode, cast iron drive-side end brackets and double sealed permanent
bearings all combine to insure maximum performance and life. Units are designed to rotate either
direction without changing the wiring, and are rated at unity power factor, requiring approximately 2
HP input for each 1000 watts output from the generator. Each unit is factory tested to insure its
performance and reliability.
MODEL NUMBER
WATTS
RATED AC AMPS
VOLTS @ 60 HZ
OPERATING SPEED
MOTOR STARTING CAPABILITY
RECEPTACLES:
120V NEMA 5-20R
120V NEMA L5-15R
120/240V NEMA L14-30R
CIRCUIT BREAKERS
LENGTH
WIDTH
HEIGHT
SHAFT DIAMETER
WEIGHT
WARRANTY
TB2400C
2400
20
120
3600 rpm
3/4 hp
TB4000C*
4000
33.3/16.7
120/240
3600 rpm
1-1/2 hp
TB6000C*
6000
50/25
120/240
3600 rpm
3 hp
TB7200GFI*
7200
60/30
120/240
3600 rpm
5 hp
2-20 amp
N/A
N/A
1-20 amp
14.25 in.
8.5 in.
8.94 in.
1.125 in.
61 lbs.
1 year
4-20 amp
N/A
1-30 amp
2-20 amp
15.13 in.
8.5 in.
8.94 in.
1.125 in.
67 lbs.
1 year
4-20 amp
N/A
1-30 amp
2-25 amp
17.75 in.
8.5 in.
8.94 in.
1.125 in.
86 lbs.
1 year
N/A
4-15 amp
1-30 amp
1-30 amp GFI, 4-15 amp
20.13 in.
8.5. in.
11.75 in.
1.125 in.
118 lbs.
1 year
* These units can be reconnected for 120V full power. Consult factory for details.
A Tradition Since 1927
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
TB 10/08
EMERGEN-C
SERIES
GENERATORS
ECV2512FPTOU-3
MODEL NUMBER
ECV2510FPTOU-3
ECV2512FPTOU-3 35PSB4G-3
45PSB4G-17
55PSB4G-3
75PSB4G-17
Electrical Specifications
Power Rating-Surge (1)
Power Rating-Cont (2)
AC Output Voltage (3)
Phase/Frequency
AC Output Amps-Cont (2)
Motor Starting (4)
Generator Rotor Speed
Conduit Mtg.KO(s) Size/(Qty)
Conductors Size/(Qty)
25/25kW
20/20kW
120/240
1-PH, 60HZ
83
7.5
3600 RPM
1-1/4” (1)
#10 (6) Pwr-36”
#4 (1) Grnd-36”
N/A
35kW
120/240
1-PH, 60HZ
146
20
1800 RPM
2” (2),1/2” (2)
None
N/A
45kW
120/240
3-PH, 60HZ
108
30
1800 RPM
2” (2),1/2” (2)
None
N/A
55kW
120/240
1-PH, 60HZ
229
30
1800 RPM
2” (2),1/2” (2)
None
N/A
75kW
120/240
3-PH, 60HZ
180
40
1800 RPM
2” (2),1/2” (2)
None
50
1000/1181 RPM
1-1/8” Keyed
Gear/Either
65
1800 RPM
1-5/8” Keyed
Direct/Either
80
1800 RPM
1-5/8” Keyed
Direct/Either
95
1800 RPM
1-5/8” Keyed
Direct/Either
125
1800 RPM
1-5/8” Keyed
Direct/Either
26.4x19.4x12.3
287/275
318/306
1 Year
28.7x19.2x16.4
416
436
1 Year
28.7x19.2x16.4
420
440
1 Year
34.8x19.2x16.4
598
618
1 Year
34.8x19.2x16.4
605
638
1 Year
Mechanical Specifications
Min Drive HP Required (5)
Input Drive Speed
Input Shaft Size
Type/Drive Rotation Direction
Product Information
L x W x H (in.)
Net Weight
Shipping Weight
Warranty Information
NOTES: (1) Surge Rating (2) Continuous Rating per NEMA MG122.40 Standards at Unity (1.0) power factor (3) +/- 7% (4) NEMA
Code G capacitor start motor (5) Required for full rated output
225 South Cordova Ave
Le Center MN 56057
East Coast: (800) 733-2112
West Coast & Canada: (800) 324-8174
E-Mail: [email protected]
Web Site: www.wincogen.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement