Konica Minolta Kit _ Bizhub _ 132320 - 200 _ 250 _ 350 - Installation Manual - EN - 2.2.9 - P

Konica Minolta Kit _ Bizhub _ 132320 - 200 _ 250 _ 350 - Installation Manual - EN - 2.2.9 - P
Konica Minolta Kit ~
Bizhub ~ 132320
Installation Manual | Konica Minolta Kit ~ Bizhub ~
132320
Product Version: 200 ~ 250 ~ 350
Version of this manual: 2.2.17
Inepro Kit number: 132320
Konica Kit number: 9967000267
© 2014 Inepro B.V. All rights reserved
Table of Contents
Introduction
Check Kit Content
Hardware Setup
2
4
10
1 Attach
........................................................................................................................................................
the PayCon to the bracket
10
2 Attach
........................................................................................................................................................
the bracket to the copier
12
Set up the copier
18
1 Konica
........................................................................................................................................................
Minolta Bizhub 250 Series
18
Set up the PayCon
22
1 Behaviour
........................................................................................................................................................ 22
2 Network
........................................................................................................................................................ 23
3 General
........................................................................................................................................................
Settings
24
Version 2.2.17 Inepro B.V.
http://www.inepro.com
Introduction
I
Part
Introduction
Introduction
This kit is meant for the following Konica Minolta Bizhub copiers:
Konica Minolta
-
Bizhub 200
Bizhub 250
Bizhub 350
Bizhub C451
Bizhub C550
Bizhub C650
To install this kit we shall:
1. Check the content of kit, read more on page
4
2. Prepare and construct the hardware. To read more go to page
3. Set up the copier, read more on page
4
4. Set up the PayCon, you will find more information on page
2
-
Konica Minolta Kit ~ Bizhub ~ 132320
4
4
Check Kit Content
II
Part
Check Kit Content
Check Kit Content
Before you start installing the kit, you should check if you have received all the packages you need.
KM Mounting kit for Bizhub 250 / 350
Please check the content of the box and make sure all kits are complete.
KM Mounting kit for Bizhub 250 / 350
In the "KM Mounting kit for Bizhub 250/350" you should find:
· 1x
KM cableset keycounter I/F
· 1x
PayCon copier mounting bracket
· 1x
KM screwset Bizhub 250 / 350
· 1x
KM Mounting plate Bizhub 250 / 350
· 1x
This manual
4
-
Konica Minolta Kit ~ Bizhub ~ 132320
KM Screwset Bizhub 250 / 350
KM Screwset Bizhub 250 / 350
In the "KM Screwset Bizhub 250 / 350" you should find:
· 12x Cable guiders
· 1x
Cable Relief
· 3x
M4 x 5mm Dome shaped, cross head screws
· 2x
M3 x 16mm Dome shaped, cross head screws
· 3x
M3 x 30mm Dome shaped, cross head screws
· 5x
M3 Star lock washers
· 3x
M4 Star lock washers
KM Mounting plate Bizhub 250 / 350
KM Mounting plate Bizhub 250 / 350
1x KM mounting plate Bizhub 250 / 350
Version 2.2.17
-
5
Check Kit Content
KM Cableset keycounter I/F
KM Cableset keycounter I/F
In the "KM Cableset keycounter I/F" you should find:
· 2x
Rip tie
· 1x
Ferrite core
· 1x
Connection cable
6
-
Konica Minolta Kit ~ Bizhub ~ 132320
PayCon copier mounting bracket
PayCon copier mounting bracket
In the "PayCon copier mounting bracket" you should find:
· 1x
PayCon copier mounting bracket
· 4x
Dome shaped, cross head screws
· 3x
Dome shaped, cross head screws (not needed for this installation)
Additional requirements for installation
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)
Version 2.2.17
-
7
Hardware Setup
III
Part
Hardware Setup
Hardware Setup
Additional requirements:
· Pair of wire cutters
· No. 2 cross head screwdriver
· No. 1 PosiDriv head screwdriver
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)
Attach the PayCon to the PayCon bracket
Please follow these steps:
1. Break out the appropriate gaps in the flaps
2. Feed the wires through the bracket and through the compartment border in the PayCon, then connect them as shown to the 'Copy_Out'
and the 'Copy_In'. Also connect the power supply to the socket bottom-left to the 'Opto COM 12' as shown in the picture on the left.
10
-
Konica Minolta Kit ~ Bizhub ~ 132320
Attach the PayCon to the bracket
3. Close the two left flaps and fasten the middle one with it's screw. Then use the rip tie to attach the power cable and connection cable to
the flap, thus creating a cable relief, and clip the rip tie using the wire cutter
4. Close and gently screw down the final flap
5. Place the PayCon bracket on the PayCon with the screws from the bracket kit
Version 2.2.17
-
11
Hardware Setup
6. Align the holes of the mounting plate with the PayCon bracket and fasten it with the 3 M4 x 5mm screws and their star lock washers
7. Wrap the power wire around the ferrite core twice, the network cables once and attach the ferrite cores to the PayCon with the adhesive
tape
8. Place the connection wire and its cable relief in the bracket
Attach the PayCon bracket to the copier
1. Unscrew the copier cover.
12
-
Konica Minolta Kit ~ Bizhub ~ 132320
Attach the bracket to the copier
2. Pull the flap towards you, to free the cover connection. Then pull the cover out from under the flap and towards you.
3. The cover is now removed from the copier and the connection wire can be seen. Release the wire from the clips, making sure you have
enough length to wrap it around the ferrite ring.
4. Use the ferrite ring to shield the wire from interference, fasten it with the rip tie. (Remove any other connectors from the main connector,
if present).
5. Break out the hole in the cover. Place the cover and the bracket on the copier and guide the wire through the hole in the cover and
connect the wire from the PayCon with that of the copier.
Version 2.2.17
-
13
Hardware Setup
6. Screw the cover and bracket in place with the M3 x 16mm and M3 x 30mm screws and fasten the cover with the cover screw
7. Place the 12 cable guiders
8. Open the little side flap to feed the network cable through
9. Guide the cables through the 12 cable guiders
14
-
Konica Minolta Kit ~ Bizhub ~ 132320
Attach the bracket to the copier
10. Remove the transport foils from the PayCon to finish the installation
11. Finished
Version 2.2.17
-
15
Set up the copier
IV
Part
Set up the copier
Set up the copier
Turn on the copier. In this chapter you will set up the copier for use with the PayCon system. Examine the exact settings
below.
Konica Minolta Bizhub Series
· Konica Minolta Bizhub 200
· Konica Minolta Bizhub 250
· Konica Minolta Bizhub 350
The PayCon Interface setting should be 'Double Click'. (See chapter: 'Set up the PayCon' on page
Activating the payment system:
1. Press <Utility>
2. Press <Check Detail>
3. Press <Stop> <0> <0> <Stop> <0> <1>
4. Press <0> <0> <0> <0> <0> <0> <0> <0> <END> Tech. Rep. Mode
5. Press <Stop> <9> Meter Count
6. Select <Key Counter>
- Select <Yes>
- Press <END>
7. Select <Vendor Mode>
- Select <OFF> (for correct working of duplex)
- Press <END>
8. Select <Total Counter>
- Select <Mode 2> (for correct working of duplex)
- Press <END>
9. Select <Large Size>
- Select <A3 11x17>
- Press <END>
10.Press <Reset>
11.Press <Exit>
18
-
Konica Minolta Kit ~ Bizhub ~ 132320
22
).
Konica Minolta Bizhub 250 Series
Version 2.2.17
-
19
Set up the PayCon
V
Part
Set up the PayCon
Set up the PayCon
Turn on the PayCon. Refer to the technical PayCon Copy manual for handling the PayCon menu and changing settings.
The settings in the PayCon can be find in the tree-top menu structure of the PayCon. To simplify thing, we will use a
graphic representation of this menu to show you where the setting can be found.
The steps are represented by icons:
Insert your service card and enter the menu
Optional ECOS module
Press 1
Press Dot
Press 2
Press 0
Press 3
Press #
Press 4
Press +
Press 5
Press -
Press 6
Press F
Press 7
Press Stop
Press 8
Press ?
Press 9
Press the Flag
Press OK
Press Correction
Use the
The
,
and
,
and
to navigate, the
buttons can also be used as the
to edit the value, the
and
to confirm and the
to cancel.
buttons to navigate.
Look for all the actions of the buttons in the PayCon technical manual.
Behaviour
1. Where is the credit value kept?
a. On the card (SVC), you will need to use cards of the chipcard or Mifare card type and the
Payment Option', continue with step 2.
b. On the server (SVS), go to step 3.
c. On the PayCon terminal, you will need ECOS 'KM - I - Local Accounts', go to step 4.
2. Stored Value on Card:
a. If you use Mifare continue with 2b, if you use chipcards go to step 2d
b. , Go to 'Main Menu' => 'Card / ID' => 'ID Tags' => 'Mifare' => 'Mode'.
and go to step 2f.
c. Select 'Disabled', press
d. , Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => 'Inepro SLE'.
e. Select 'Disabled' and press .
f. Do you use Pcounter? if you do, continue with step 3, if you don't, go to step 8.
3. Do you use Cost Centres (Client Codes) in the PayCon System*?
* Sub Client Codes are not supported.
22
-
Konica Minolta Kit ~ Bizhub ~ 132320
ECOS 'KM - PayCon
Behaviour
a. , Go to 'Main Menu' => 'Card / ID' => 'General Settings' => 'Cost Centre Selection'.
b. If everybody is required to use a Cost Centre (Client Code), choose 'Required' and confirm with
not be able to use budget purses if there is no server connection.
c. If you don't use Cost Centres, choose 'Never' and confirm with .
d. If you only want to use it if the server is online, choose 'If online' and confirm with .
e. Go to step 5.
. The users will
4. Store Value on Terminal:
a. Set the account mode. , Go to 'Main Menu' => 'Card/ID' => 'Terminal Accounts' => 'Account Mode'.
and go to step 4e.
b. If you want all tags to be accepted select 'Allow all ID's' and confirm with
c. If you want to accept only tags that are registered in your PayCon select 'Allow accounts' and confirm with .
d. Setting up the accounts:
, Go to 'Main Menu' => 'Card/ID' => 'Terminal Accounts' => 'Add'.
·
to add an account.
· Type a card or account number and confirm with
· Repeat this until all accounts are set.
e. Setting the tags:
, Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => <Tag Type>.
·
· Select 'Disabled' and press .
, Go to 'Main Menu' => 'Card / ID' => 'Terminal Accounts' => 'Tags' => <Tag Type>.
·
· There are two ways to present a tag to the PayCon, you can swipe it past the reader or hold it in place on the
reader.
· Select 'Hold' or 'Swipe' and confirm with .
f. Go to Step 8
Network
5. Network Settings:
a. , Go to 'Main Menu' => 'Terminal' => 'Network'
b. Set the 'host name' to an identifiable name.
c. Confirm with .
d. If DHCP is used and go to step 7.
e. If DHCP isn't used, set it to 'disabled' and confirm with
.
6. Fixed IP addresses:
a. Set 'IP-address' to an IP-address in your network range and confirm with .
b. Set the subnet mask ('netmask') to '255.255.255.0' or to the subnet mask needed in your network and confirm with
.
c. Set the 'default gateway' to the IP-address of the default gateway in your network and confirm with .
7. DB Settings:
a. , Go to 'Main Menu' => 'DB Connectivity' => 'Server'
b. Set the IP-address of the PCounter server in 'Sever Address' and confirm with
c. , Go to 'Main Menu' => 'DB Connectivity' => 'Transaction log'
d. Select 'Enabled' and confirm with .
e. , Go to 'Main Menu' => 'DB Connectivity' => 'Printjob client'
f. Select 'Enabled' and confirm with .
.
Version 2.2.17
-
23
Set up the PayCon
General Settings
8. Copier Interface:
a. , Go to 'Main Menu' => 'Copier' => 'Interface'
b. Select the Interface setting for your machine and press
the copier', on page 18 .
. The correct settings can be found in the chapter: 'Set up
9. Products. The copy/print/scan products in the PayCon have a fixed order and number. They are used to connect the
paper signals form the copier to prices in the PayCon. These products and their names can also be set with PCounter.
a. , Go to 'Main Menu' => 'Products' => 'Product List'
b. Check if the default product list is complete, if so go to step 11, if not continue with step 10.
PayCon
product
number
0
1
2
3
4
5
6
7
1000
1001
1002
1003
1004
1005
1006
1007
2000
2001
2002
2003
3000
3001
3008
PayCon product
display name
A4 b/w
A3 b/w
A4 colour
A3 colour
A4 b/w dpx
A3 b/w dpx
A4C dpx
A3C dpx
Print A4 b/w
Print A3 b/w
Print A4C
Print A3C
Print A4 b/w dpx
Print A3 b/w dpx
Print A4 colour dpx
Print A3 colour dpx
Scan A4 b/w
Scan A3 b/w
Scan A4C
Scan A3C
Fax A4
Fax A3
Fax Start
PayCon
default
price
€ 0,05
€ 0,10
€ 0,50
€ 1,00
€ 0,05
€ 0,10
€ 0,50
€ 1,00
€ 0,05
€ 1,00
€ 0,50
€ 1,00
€ 0,05
€ 0,10
€ 0,50
€ 1,00
€ 0,01
€ 0,02
€ 0,03
€ 0,06
€ 0,05
€ 0,10
€ 0,25
Supported by
Corresponds with photocopier product
A4 black and white
A4 black and white
A4 colour (single until full)
A3 colour (single until full)
Backside of duplex A4 black copy
Backside of duplex A3 black copy
Backside of duplex A4 colour copy
Backside of duplex A3 colour copy
A4 black and white print
A3 black and white print
A4 colour print
A3 colour print
A4 black and white duplex print
A3 black and white duplex print
A4 colour duplex print
A3 colour duplex print
A4 black and white scan
A3 black and white scan
A4 colour scan
A3 colour scan
A4 black and white fax
A3 black and white fax
Start tariff for fax
200, 250, 350
X
X
-
Note that not every product is supported by each interface!
X
= Supported
= Not supported
10. Edit Product:
a. To add a product, go to 'Add product', enter a number and press .
b. To edit it's properties, go to 'Main Menu' => 'Products' => 'Product List', select it and press .
c. Check the price and if the index number corresponds with the copy product index number in the table.
11. Purse Selection, manage the way the purse is selected.
a. , Go to 'Main Menu' => 'Card/ID' => 'Generic Settings' => 'Purse Selection'.
b. Select the selection behaviour in the list (look for a description in the table) confirm with
24
-
Konica Minolta Kit ~ Bizhub ~ 132320
.
General Settings
Purse Selection
All Purses
Personal Only
Budget Only
Prefer Personal
Prefer Budget
Personal + Ask
Budget + Ask
Description
Accept all purses
Only accept personal credit
Only accept non-personal budget
If the card has a personal credit, pay out of that credit
If the card has a non-personal budget, pay out of that budget
Ask which budget and select personal credit as default
Ask which budget and select non-personal budget as default
12. Maximum Balance, the Maximum Balance allowed on a card or account.
a. , Go to 'Main Menu' => 'Card/ID' => 'Generic Settings' => 'Maximum Balance'.
b. Type in the maximum balance and confirm with .
13.Project ID, the unique number for all PayCon's on this project or site.
a. , Go to 'Main Menu' => 'Terminal' => 'Project ID'
b. Press , type the Project ID and confirm with .
14. Date and Time, the time and date that are used for the timestamp on the transactions. Remember if the timezone is
changed the time will change accordingly.
a. So first set the timezone by , go to 'Main Menu' => 'Terminal' => 'Date/Time' => 'Timezone'.
b. Select the timezone and confirm with .
c. Check the time (go to 'Main Menu' => 'Terminal' => 'Date/Time' => 'Time') and change it if needed.
d. In the same manner check the date.
15. Currency, the currency used in the PayCon
a. , Go to 'Main Menu' => 'Terminal' => 'Currency' => 'Accepted Currency'.
b. Select the currency and confirm with .
c. Go to 'Main Menu' => 'Terminal' => 'Currency' => 'Old Currency'.
d. Select the currency and confirm with .
16. Default language, the language the PayCon uses to communicate with the user. A second and third language can
also be set. When the user presses , the next available language will be used.
a. , Go to 'Main Menu' => 'Terminal' => 'Default Language'.
b. Select a language from the list and confirm with .
c. Go to 'Main Menu' => 'Terminal' => '<Nth> Language' to add extra languages in the same way.
Version 2.2.17
-
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement