A-Gas MPG Concentrate

A-Gas MPG Concentrate
A-Gas MPG Concentrate
A-Gas (Australia) Pty Ltd
Chemwatch Hazard Alert Code: 2
Issue Date: 09/09/2013
Print Date: 13/02/2014
Initial Date: Not Available
S.Local.AUS.EN
Chemwatch: 7632-89
Version No: 4.1.1.1
Material Safety Data Sheet according to NOHSC and ADG requirements
SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING
Product Identifier
Product name
Chemical Name
Synonyms
A-Gas MPG Concentrate
Not Applicable
Not Available
Proper shipping name
Not Applicable
Chemical formula
Not Applicable
Other means of identification
CAS number
Not Available
Not Applicable
Relevant identified uses of the substance or mixture and uses advised against
Relevant identified uses
Use according to manufacturer's directions.
Details of the supplier of the safety data sheet
Registered company name
Address
Telephone
Fax
Website
Email
A-Gas (Australia) Pty Ltd
9-11 Oxford Road Laverton North VIC 3026
Australia
[+61] (0) 3 93689222
[+61] (0) 3 93689233
www.agas.com
[email protected]
Emergency telephone number
Association / Organisation
Not Available
Emergency telephone numbers
TOLL: [+61] 1800 024 973
Other emergency telephone numbers
TOLL: [+61] 1800 024 973
CHEMWATCH EMERGENCY RESPONSE
Primary Number
Alternative Number 1
Alternative Number 2
1800 039 008
+612 9186 1132
Not Available
Once connected and if the message is not in your prefered language then please dial 01
SECTION 2 HAZARDS IDENTIFICATION
Classification of the substance or mixture
NON-HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS. According to NOHSC Criteria, and ADG Code.
CHEMWATCH HAZARD RATINGS
Min
Flammability
Toxicity
Body Contact
Reactivity
Chronic
Max
1
2
2
1
2
0 = Minimum
1 = Low
2 = Moderate
3 = High
4 = Extreme
Poisons Schedule
Risk Phrases
Legend:
GHS Classification
Legend:
None
Not Applicable
1. Classified by Chemwatch; 2. Classification drawn from HSIS ; 3. Classification drawn from EC Directive 1272/2008 - Annex VI
Not Applicable
1. Classified by Chemwatch; 2. Classification drawn from HSIS ; 3. Classification drawn from EC Directive 1272/2008 - Annex VI
Continued...
Chemwatch: 7632-89
Version No: 4.1.1.1
Page 2 of 8
Issue Date: 09/09/2013
A-Gas MPG Concentrate
Print Date: 13/02/2014
Label elements
GHS label elements
SIGNAL WORD
NOT APPLICABLE
Hazard statement(s)
Not Applicable
Precautionary statement(s): Prevention
Not Applicable
Precautionary statement(s): Response
Not Applicable
Precautionary statement(s): Storage
Not Applicable
Precautionary statement(s): Disposal
Not Applicable
Label elements
Relevant risk statements are found in section 2
Indication(s) of danger
Not Applicable
SAFETY ADVICE
Not Applicable
Other hazards
May produce discomfort of the eyes and skin*.
Ingestion may produce health damage*.
Possible skin sensitizer*.
Repeated exposure potentially causes skin dryness and cracking*.
Vapours potentially cause drowsiness and dizziness*.
SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS
Substances
See section below for composition of Mixtures
Mixtures
CAS No
%[weight]
Name
57-55-6
>95
propylene glycol
7632-00-0
<1
sodium nitrite
SECTION 4 FIRST AID MEASURES
Description of first aid measures
Eye Contact
Skin Contact
If this product comes in contact with the eyes:
Wash out immediately with fresh running water.
Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and
lower lids.
Seek medical attention without delay; if pain persists or recurs seek medical attention.
Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.
If skin contact occurs:
Immediately remove all contaminated clothing, including footwear.
Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
Inhalation
If fumes or combustion products are inhaled remove from contaminated area.
Lay patient down. Keep warm and rested.
Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aid procedures.
Apply artificial respiration if not breathing, preferably with a demand valve resuscitator, bag-valve mask device, or pocket mask as trained.
Perform CPR if necessary.
Transport to hospital, or doctor.
Ingestion
If swallowed do NOT induce vomiting.
If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain open airway and prevent aspiration.
Observe the patient carefully.
Never give liquid to a person showing signs of being sleepy or with reduced awareness; i.e. becoming unconscious.
Give water to rinse out mouth, then provide liquid slowly and as much as casualty can comfortably drink.
Seek medical advice.
Indication of any immediate medical attention and special treatment needed
Treat symptomatically.
Continued...
Chemwatch: 7632-89
Version No: 4.1.1.1
Page 3 of 8
Issue Date: 09/09/2013
A-Gas MPG Concentrate
Print Date: 13/02/2014
To treat poisoning by the higher aliphatic alcohols (up to C7):
Gastric lavage with copious amounts of water.
It may be beneficial to instill 60 ml of mineral oil into the stomach.
Oxygen and artificial respiration as needed.
Electrolyte balance: it may be useful to start 500 ml. M/6 sodium bicarbonate intravenously but maintain a cautious and conservative attitude
toward electrolyte replacement unless shock or severe acidosis threatens.
To protect the liver, maintain carbohydrate intake by intravenous infusions of glucose.
Haemodialysis if coma is deep and persistent. [GOSSELIN, SMITH HODGE: Clinical Toxicology of Commercial Products, Ed 5)
----------------------------------------------------------------BASIC TREATMENT
----------------------------------------------------------------Establish a patent airway with suction where necessary.
Watch for signs of respiratory insufficiency and assist ventilation as necessary.
Administer oxygen by non-rebreather mask at 10 to 15 l/min.
Monitor and treat, where necessary, for shock.
Monitor and treat, where necessary, for pulmonary oedema.
Anticipate and treat, where necessary, for seizures.
DO NOT use emetics. Where ingestion is suspected rinse mouth and give up to 200 ml water (5 ml/kg recommended) for dilution where
patient is able to swallow, has a strong gag reflex and does not drool.
Give activated charcoal.
----------------------------------------------------------------ADVANCED TREATMENT
----------------------------------------------------------------Consider orotracheal or nasotracheal intubation for airway control in unconscious patient or where respiratory arrest has occurred.
Positive-pressure ventilation using a bag-valve mask might be of use.
Monitor and treat, where necessary, for arrhythmias.
Start an IV D5W TKO. If signs of hypovolaemia are present use lactated Ringers solution. Fluid overload might create complications.
If the patient is hypoglycaemic (decreased or loss of consciousness, tachycardia, pallor, dilated pupils, diaphoresis and/or dextrose strip or
glucometer readings below 50 mg), give 50% dextrose.
Hypotension with signs of hypovolaemia requires the cautious administration of fluids. Fluid overload might create complications.
Drug therapy should be considered for pulmonary oedema.
Treat seizures with diazepam.
Proparacaine hydrochloride should be used to assist eye irrigation.
----------------------------------------------------------------EMERGENCY DEPARTMENT
----------------------------------------------------------------Laboratory analysis of complete blood count, serum electrolytes, BUN, creatinine, glucose, urinalysis, baseline for serum aminotransferases
(ALT and AST), calcium, phosphorus and magnesium, may assist in establishing a treatment regime. Other useful analyses include anion
and osmolar gaps, arterial blood gases (ABGs), chest radiographs and electrocardiograph.
Positive end-expiratory pressure (PEEP)-assisted ventilation may be required for acute parenchymal injury or adult respiratory distress
syndrome.
Acidosis may respond to hyperventilation and bicarbonate therapy.
Haemodialysis might be considered in patients with severe intoxication.
Consult a toxicologist as necessary. BRONSTEIN, A.C. and CURRANCE, P.L. EMERGENCY CARE FOR HAZARDOUS MATERIALS
EXPOSURE: 2nd Ed. 1994
For C8 alcohols and above.
Symptomatic and supportive therapy is advised in managing patients.
Propylene glycol is primarily a CNS depressant in large doses and may cause hypoglycaemia, lactic acidosis and seizures.
The usual measures are supportive care and decontamination (Ipecac/ lavage/ activated charcoal/ cathartics), within 2 hours of exposure
should suffice.
Check the anion gap, arterial pH, renal function and glucose levels.
Ellenhorn and Barceloux: Medical Toxicology
SECTION 5 FIREFIGHTING MEASURES
Extinguishing media
Alcohol stable foam.
Dry chemical powder.
BCF (where regulations permit).
Carbon dioxide.
Special hazards arising from the substrate or mixture
Fire Incompatibility
Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition may result
Advice for firefighters
Fire Fighting
Fire/Explosion Hazard
Alert Fire Brigade and tell them location and nature of hazard.
Wear full body protective clothing with breathing apparatus.
Prevent, by any means available, spillage from entering drains or water course.
Use water delivered as a fine spray to control fire and cool adjacent area.
Combustible.
Slight fire hazard when exposed to heat or flame.
Heating may cause expansion or decomposition leading to violent rupture of containers.
On combustion, may emit toxic fumes of carbon monoxide (CO).
SECTION 6 ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Continued...
Chemwatch: 7632-89
Version No: 4.1.1.1
Issue Date: 09/09/2013
A-Gas MPG Concentrate
Print Date: 13/02/2014
Remove all ignition sources.
Clean up all spills immediately.
Avoid breathing vapours and contact with skin and eyes.
Control personal contact with the substance, by using protective equipment.
Minor Spills
Major Spills
Page 4 of 8
Moderate hazard.
Clear area of personnel and move upwind.
Alert Fire Brigade and tell them location and nature of hazard.
Wear breathing apparatus plus protective gloves.
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
SECTION 7 HANDLING AND STORAGE
Precautions for safe handling
Safe handling
Other information
DO NOT allow clothing wet with material to stay in contact with skin
Avoid all personal contact, including inhalation.
Wear protective clothing when risk of exposure occurs.
Material is hygroscopic, i.e. absorbs moisture from the air. Keep containers well sealed in storage.
Store in original containers.
Keep containers securely sealed.
Conditions for safe storage, including any incompatibilities
Suitable container
Storage incompatibility
Metal can or drum
Packaging as recommended by manufacturer.
Check all containers are clearly labelled and free from leaks.
Alcohols
are incompatible with strong acids, acid chlorides, acid anhydrides, oxidising and reducing agents.
reacts, possibly violently, with alkaline metals and alkaline earth metals to produce hydrogen
react with strong acids, strong caustics, aliphatic amines, isocyanates, acetaldehyde, benzoyl peroxide, chromic acid, chromium oxide,
dialkylzincs, dichlorine oxide, ethylene oxide, hypochlorous acid, isopropyl chlorocarbonate, lithium tetrahydroaluminate, nitrogen dioxide,
pentafluoroguanidine, phosphorus halides, phosphorus pentasulfide, tangerine oil, triethylaluminium, triisobutylaluminium
PACKAGE MATERIAL INCOMPATIBILITIES
SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Control parameters
OCCUPATIONAL EXPOSURE LIMITS (OEL)
INGREDIENT DATA
Source
Ingredient
Material name
TWA
STEL
Peak
Notes
Australia Exposure Standards
propylene
glycol
Propane-1,2-diol total: (vapour & particulates) /
Propane-1,2-diol: particulates only
474 (mg/m3) / 10
(mg/m3) / 150 (ppm)
Not
Available
Not
Available
Not
Available
EMERGENCY LIMITS
Ingredient
TEEL-0
TEEL-1
TEEL-2
TEEL-3
propylene glycol
10(ppm)
10(ppm)
10(ppm)
500(ppm)
sodium nitrite
0.04(ppm)
0.125(ppm)
1(ppm)
60(ppm)
Ingredient
Original IDLH
Revised IDLH
A-Gas MPG Concentrate
Not Available
Not Available
Exposure controls
Appropriate engineering controls
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed engineering controls
can be highly effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection.
The basic types of engineering controls are:
Process controls which involve changing the way a job activity or process is done to reduce the risk.
Personal protection
Eye and face protection
Skin protection
Hand protection
Safety glasses with side shields.
Chemical goggles.
Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing
the wearing of lens or restrictions on use, should be created for each workplace or task.
See Hand protection below
Wear chemical protective gloves, e.g. PVC.
Wear safety footwear or safety gumboots, e.g. Rubber
NOTE:
The material may produce skin sensitisation in predisposed individuals.
Continued...
Chemwatch: 7632-89
Version No: 4.1.1.1
Body protection
Page 5 of 8
Issue Date: 09/09/2013
A-Gas MPG Concentrate
Print Date: 13/02/2014
See Other protection below
Overalls.
P.V.C. apron.
Barrier cream.
Other protection
Thermal hazards
Recommended material(s)
Respiratory protection
Type A-P Filter of sufficient capacity
GLOVE SELECTION INDEX
Glove selection is based on a modified presentation of the:
"Forsberg Clothing Performance Index".
The effect(s) of the following substance(s) are taken into account in the
A-Gas MPG Concentrate
Material
CPI
PE/EVAL/PE
A
* CPI - Chemwatch Performance Index
A: Best Selection
B: Satisfactory; may degrade after 4 hours continuous immersion
C: Poor to Dangerous Choice for other than short term immersion
Where the concentration of gas/particulates in the breathing zone,
approaches or exceeds the "Exposure Standard" (or ES), respiratory
protection is required.
Degree of protection varies with both face-piece and Class of filter;
the nature of protection varies with Type of filter.
Required
Minimum
Protection
Factor
Half-Face
Respirator
up to 5 x ES
A-AUS / Class 1
P2
A-PAPR-AUS /
Class 1 P2
up to 25 x ES
Air-line*
A-PAPR-2 P2
Full-Face
Respirator
A-2 P2
Powered Air
Respirator
up to 50 x ES
-
A-3 P2
-
50+ x ES
-
Air-line**
-
* - Continuous-flow; ** - Continuous-flow or positive pressure
demand
^ - Full-face
A(All classes) = Organic vapours, B AUS or B1 = Acid gasses, B2 =
Acid gas or hydrogen cyanide(HCN), B3 = Acid gas or hydrogen
cyanide(HCN), E = Sulfur dioxide(SO2), G = Agricultural chemicals,
K = Ammonia(NH3), Hg = Mercury, NO = Oxides of nitrogen, MB =
Methyl bromide, AX = Low boiling point organic compounds(below
65 degC)
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
Appearance
Physical state
Blue-green liquid with a mild odour; mixes with water.
Liquid
Relative density (Water = 1)
1.0
Odour
Not Available
Partition coefficient n-octanol / water
Not Available
Odour threshold
Not Available
Auto-ignition temperature (°C)
Not Available
pH (as supplied)
Not Available
Decomposition temperature
Not Available
Melting point / freezing point (°C)
Not Available
Viscosity (cSt)
Not Available
Initial boiling point and boiling range
(°C)
Not Available
Molecular weight (g/mol)
Flash point (°C)
100
Not Applicable
Taste
Not Available
Not Available
Evaporation rate
Not Available
Explosive properties
Flammability
Not Available
Oxidising properties
Not Available
Upper Explosive Limit (%)
Not Available
Surface Tension (dyn/cm or mN/m)
Not Available
Lower Explosive Limit (%)
Not Available
Volatile Component (%vol)
Not Available
Vapour pressure (kPa)
Not Available
Solubility in water (g/L)
Miscible
Vapour density (Air = 1)
Not Available
Gas group
pH as a solution(1%)
VOC g/L
Not Available
8.4 as 33% soln.
Not Available
SECTION 10 STABILITY AND REACTIVITY
Reactivity
Chemical stability
See section 7
Presence of incompatible materials.
Product is considered stable.
Hazardous polymerisation will not occur.
Possibility of hazardous reactions
See section 7
Conditions to avoid
See section 7
Incompatible materials
See section 7
Continued...
Chemwatch: 7632-89
Version No: 4.1.1.1
Hazardous decomposition products
Page 6 of 8
Issue Date: 09/09/2013
A-Gas MPG Concentrate
Print Date: 13/02/2014
See section 5
SECTION 11 TOXICOLOGICAL INFORMATION
Information on toxicological effects
Inhaled
Ingestion
Inhalation of vapours may cause drowsiness and dizziness. This may be accompanied by narcosis, reduced alertness, loss of reflexes, lack of
coordination and vertigo.
Inhalation of vapours or aerosols (mists, fumes), generated by the material during the course of normal handling, may be damaging to the health
of the individual.
Inhalation hazard is increased at higher temperatures.
Accidental ingestion of the material may be damaging to the health of the individual.
Effects on the nervous system characterise over-exposure to higher aliphatic alcohols. These include headache, muscle weakness, giddiness,
ataxia, (loss of muscle coordination), confusion, delirium and coma. Gastrointestinal effects may include nausea, vomiting and diarrhoea.
Skin Contact
The material may produce moderate skin irritation; limited evidence or practical experience suggests, that the material either:
produces moderate inflammation of the skin in a substantial number of individuals following direct contact and/or
produces significant, but moderate, inflammation when applied to the healthy intact skin of animals (for up to four hours), such inflammation
being present twenty-four hours or more after the end of the exposure period.
Skin irritation may also be present after prolonged or repeated exposure; this may result in a form of contact dermatitis (nonallergic).
Eye
Irritation of the eyes may produce a heavy secretion of tears (lachrymation).
Limited evidence or practical experience suggests, that the material may cause eye irritation in a substantial number of individuals. Repeated or
prolonged eye contact may cause inflammation characterised by temporary redness (similar to windburn) of the conjunctiva (conjunctivitis);
temporary impairment of vision and/or other transient eye damage/ulceration may occur.
Chronic
There exists limited evidence that shows that skin contact with the material is capable either of inducing a sensitisation reaction in a significant
number of individuals, and/or of producing positive response in experimental animals.
Propylene glycol is though, by some, to be a sensitising principal following the regular use of topical creams by eczema patients. A study of 866
persons using a formulation containing propylene glycol in a patch test indicated that propylene glycol caused primary irritation in 16% of
exposed individuals probably caused by dehydration. Undiluted propylene glycol was tested on 1556 persons in a 24 hour patch test.
TOXICITY
IRRITATION
Not Available
Not Available
TOXICITY
IRRITATION
Dermal (rabbit) LD50: 11890 mg/kg
Eye (rabbit): 100 mg - mild
Dermal (rabbit) LD50: 20800 mg/kg
Eye (rabbit): 500 mg/24h - mild
Oral (rat) LD50: 20000 mg/kg
Skin(human):104 mg/3d Intermit Mod
A-Gas MPG Concentrate
propylene glycol
Skin(human):500 mg/7days mild
Not Available
sodium nitrite
Not Available
TOXICITY
IRRITATION
Inhalation (rat) LC50: 5.5 mg/m3/4H
Eye (rabbit): 500 mg/24hr - mild
Oral (rat) LD50: 180 mg/kg
Not Available
Not Available
* Value obtained from manufacturer's msds
unless otherwise specified data extracted from RTECS - Register of Toxic Effects of Chemical Substances
A-Gas MPG Concentrate
The material may cause skin irritation after prolonged or repeated exposure and may produce a contact dermatitis (nonallergic). This form of
dermatitis is often characterised by skin redness (erythema) and swelling the epidermis. Histologically there may be intercellular oedema of
the spongy layer (spongiosis) and intracellular oedema of the epidermis.
PROPYLENE GLYCOL
The material may cause skin irritation after prolonged or repeated exposure and may produce a contact dermatitis (nonallergic). This form of
dermatitis is often characterised by skin redness (erythema) and swelling the epidermis. Histologically there may be intercellular oedema of
the spongy layer (spongiosis) and intracellular oedema of the epidermis.
The acute oral toxicity of propylene glycol is very low, and large quantities are required to cause perceptible health damage in humans.
SODIUM NITRITE
The material may be irritating to the eye, with prolonged contact causing inflammation. Repeated or prolonged exposure to irritants may
produce conjunctivitis.
Tumorigenic - Carcinogenic by RTECS criteria.
Acute Toxicity
Not Applicable
Carcinogenicity
Not Applicable
Skin Irritation/Corrosion
Not Applicable
Reproductivity
Not Applicable
Serious Eye Damage/Irritation
Not Applicable
STOT - Single Exposure
Not Applicable
Respiratory or Skin sensitisation
Not Applicable
STOT - Repeated Exposure
Not Applicable
Mutagenicity
Not Applicable
Aspiration Hazard
Not Applicable
CMR STATUS
Continued...
Chemwatch: 7632-89
Version No: 4.1.1.1
Page 7 of 8
Issue Date: 09/09/2013
A-Gas MPG Concentrate
Print Date: 13/02/2014
SECTION 12 ECOLOGICAL INFORMATION
Toxicity
DO NOT discharge into sewer or waterways.
Persistence and degradability
Ingredient
Persistence: Water/Soil
Persistence: Air
Not Available
Not Available
Not Available
Bioaccumulative potential
Ingredient
Bioaccumulation
Not Available
Not Available
Mobility in soil
Ingredient
Mobility
Not Available
Not Available
SECTION 13 DISPOSAL CONSIDERATIONS
Waste treatment methods
Product / Packaging disposal
Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to laws operating in their
area. In some areas, certain wastes must be tracked.
A Hierarchy of Controls seems to be common - the user should investigate:
SECTION 14 TRANSPORT INFORMATION
Labels Required
Marine Pollutant
HAZCHEM
NO
Not Applicable
Land transport (ADG): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Air transport (ICAO-IATA / DGR): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Sea transport (IMDG-Code / GGVSee): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Transport in bulk according to Annex II of MARPOL 73 / 78 and the IBC code
Source
Ingredient
Pollution Category
Residual Concentration - Outside Special Area (% w/w)
Residual Concentration
IMO MARPOL 73/78 (Annex II) - List of
Other Liquid Substances
propylene glycol
Not Available
Not Available
Not Available
SECTION 15 REGULATORY INFORMATION
Safety, health and environmental regulations / legislation specific for the substance or mixture
propylene glycol(57-55-6) is found on
the following regulatory lists
"IOFI Global Reference List of Chemically Defined Substances","International Council of Chemical Associations (ICCA) - High Production
Volume List","Australia Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 5","Australia Standard for the
Uniform Scheduling of Medicines and Poisons (SUSMP) - Appendix F (Part 3)","Australia Exposure Standards","IMO MARPOL 73/78 (Annex
II) - List of Other Liquid Substances","IMO Provisional Categorization of Liquid Substances - List 3: (Trade-named) mixtures containing at least
99% by weight of components already assessed by IMO, presenting safety hazards","FisherTransport Information","Australia FAISD Handbook First Aid Instructions, Warning Statements, and General Safety Precautions","OSPAR National List of Candidates for Substitution –
Norway","OECD List of High Production Volume (HPV) Chemicals","Australia Standard for the Uniform Scheduling of Medicines and Poisons
(SUSMP) - Appendix B (Part 3)","International Numbering System for Food Additives","IMO IBC Code Chapter 18: List of products to which the
Code does not apply","Sigma-AldrichTransport Information","Australia National Pollutant Inventory","Australia High Volume Industrial Chemical
List (HVICL)","Australia Australian Pesticides and Veterinary Medicines Authority (APVM) Record of approved active
constituents","GESAMP/EHS Composite List - GESAMP Hazard Profiles","Australia Standard for the Uniform Scheduling of Medicines and
Poisons (SUSMP) - Appendix E (Part 2)","Australia Hazardous Substances Information System - Consolidated Lists","IMO IBC Code Chapter
17: Summary of minimum requirements"
sodium nitrite(7632-00-0) is found on
the following regulatory lists
"International Maritime Dangerous Goods Requirements (IMDG Code)","IMO MARPOL 73/78 (Annex II) - List of Noxious Liquid Substances
Carried in Bulk","International Council of Chemical Associations (ICCA) - High Production Volume List","Australia - Victoria Occupational
Health and Safety Regulations - Schedule 9: Materials at Major Hazard Facilities (And Their Threshold Quantity) Table 2","Australia Standard
for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 5","Australia Standard for the Uniform Scheduling of Medicines and
Poisons (SUSMP) - Appendix F (Part 3)","International Maritime Dangerous Goods Requirements (IMDG Code) - Substance Index","Australia
- Tasmania - Work Health and Safety Regulations 2012 - Restricted hazardous chemicals","Australia - Australian Capital Territory - Environment
Protection Regulation: Ambient environmental standards (STOCK - inorganic chemicals)","Australia - Australian Capital Territory - Environment
Protection Regulation: Ambient environmental standards (Domestic water supply - inorganic chemicals)","United Nations Recommendations on
the Transport of Dangerous Goods Model Regulations (English)","International Agency for Research on Cancer (IARC) - Agents Reviewed by
the IARC Monographs","FisherTransport Information","Australia FAISD Handbook - First Aid Instructions, Warning Statements, and General
Safety Precautions","Australia Dangerous Goods Code (ADG Code) - List of Emergency Action Codes","Australia - Northern Territories Work
Health and Safety National Uniform Legislation Regulations- Restricted hazardous chemicals","Australia - Australian Capital Territory Environment Protection Regulation: Pollutants entering waterways taken to cause environmental harm (STOCK)","Australia Standard for the
Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 2","OECD List of High Production Volume (HPV) Chemicals","Australia
Continued...
Chemwatch: 7632-89
Version No: 4.1.1.1
Page 8 of 8
Issue Date: 09/09/2013
A-Gas MPG Concentrate
Print Date: 13/02/2014
Drinking Water Guideline Values For Physical and Chemical Characteristics","Australia - Western Australia Hazardous Substances Prohibited
for Specified Uses or Methods of Handling","Australia - Queensland Work Health and Safety Regulation - Restricted hazardous
chemicals","Australia - South Australia - Work Health and Safety Regulations 2012 - Restricted hazardous chemicals","International Numbering
System for Food Additives","Australia - Australian Capital Territory - Environment Protection Regulation: Pollutants entering waterways taken to
cause environmental harm (Aquatic habitat)","United Nations Recommendations on the Transport of Dangerous Goods Model Regulations
(Spanish)","Sigma-AldrichTransport Information","Australia - Australian Capital Territory - Environment Protection Regulation: Pollutants
entering waterways taken to cause environmental harm - Domestic water supply quality","Australia National Pollutant Inventory","Australia Australian Capital Territory - Environment Protection Regulation: Ambient environmental standards (AQUA/1 to 6 - inorganic
chemicals)","Australia - New South Wales - Work Health and Safety Regulation 2011 Restricted hazardous chemicals","GESAMP/EHS
Composite List - GESAMP Hazard Profiles","Regulations concerning the International Carriage of Dangerous Goods by Rail - Table A:
Dangerous Goods List - RID 2013 (English)","International Air Transport Association (IATA) Dangerous Goods Regulations","Australia
Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP) - Appendix E (Part 2)","Australia Dangerous Goods Code (ADG
Code) - Dangerous Goods List","Australia Hazardous Substances Information System - Consolidated Lists","Australia Work Health and Safety
Regulations 2011 - Restricted hazardous chemicals","IMO IBC Code Chapter 17: Summary of minimum requirements","Australia Standard for
the Uniform Scheduling of Medicines and Poisons (SUSMP) - Schedule 6","Australia Standard for the Uniform Scheduling of Medicines and
Poisons (SUSMP) - Schedule 7","Australia - New South Wales Protection of the Environment Operations (Waste) Regulation 2005 Characteristics of trackable wastes"
SECTION 16 OTHER INFORMATION
Other information
Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch Classification committee using
available literature references.
A list of reference resources used to assist the committee may be found at:
www.chemwatch.net/references
The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks in the workplace or other
settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or available engineering controls must be considered.
This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or criticism, as permitted under the Copyright Act, no part may be reproduced by any
process without written permission from CHEMWATCH. TEL (+61 3) 9572 4700.
end of SDS
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement