MF28-J

MF28-J
MADRONA
DV Gas Fireplace Heater (engine only)
MF28JLN (NG) & MF28JLP (LPG)
Engine to be installed ONLY with the cast stove body MFCS01, MFCS02 or MFCS04
Installation & Owner’s Manual
!
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing
glass is provided with this appliance and shall be installed
for the protection of children and other at-risk individuals.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury or loss of life.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light the appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
Leave this manual
with the appliance.
CONSUMER
Retain this manual
for future reference.
Please read this manual
BEFORE installing and
operating this appliance.
This manual contains instructions to install the
ENGINE ONLY. A stove casing is REQUIRED
to install the engine. A barrier screen is provided
with the stove casing. Refer to the manual supplied with the stove casing for installation.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Ce guide est disponible en français sur demande.
Miles Industries Ltd.
www.valorfireplaces.com
4003894-04
©2013, Miles Industries Ltd. All rights reserved.
I N S TA L L E R
Table of Contents
FOR THE OWNER
Remote Control Operation............................... 10
LOR
A
WA R R
NTY
M
GR A
O
PR
T
Owner’s Information .......................................... 5
Warranty Card at the
back of this manual.
OR
Safety and Your Fireplace ................................. 4
VA
Safety Precautions ............................................ 3
CO M F
Options ............................................................ 14
Lighting Instructions......................................... 15
Warranty .......................................................... 38
FOR THE QUALIFIED INSTALLER
Commonwealth of Massachusetts................... 16
Front and Barrier Screen Installation ............... 34
Specifications .................................................. 18
Dimensions & Clearances ............................... 19
Remote Control Handset Wall Holder
Installation ....................................................... 34
Venting............................................................. 21
Wiring Diagram ................................................ 35
Installation Planning ........................................ 26
Approved Venting Components ....................... 36
Appliance Preparation ..................................... 26
Warranty .......................................................... 38
Supply Gas Installation .................................... 30
Spare Parts...................................................... 39
Ceramic Logs Installation ................................ 31
Window Refitting.............................................. 32
Remote Control Initial Set-up .......................... 33
Operation Check & Aeration Settings
Adjustment....................................................... 33
Massachusetts: The piping and final
gas connection must be performed by a
licensed plumber or gas fitter in the State of
Massachusetts. Also, see Carbon Monoxide
Detector requirements on page 16.
The information contained in this installation
manual is believed to be correct at the time of
printing. Miles Industries Ltd. reserves the right
to change or modify any information or specifications without notice. Miles Industries Ltd. grants
no warranty, implied or stated, for the installation
or maintenance of your heater, and assumes no
responsibility for any consequential damage(s).
Designed and Manufactured by / for
Miles Industries Ltd.
190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1
Tel. 604-984-3496 Fax 604-984-0246
www.valorfireplaces.com
© Copyright Miles Industries Ltd., 2013
2
!
Safety Precautions
READ and UNDERSTAND all instructions carefully
before starting the installation. FAILURE TO FOLLOW
these installation instructions may result in possible fire
hazard and will void the warranty.
Prior to the first firing of the fireplace, READ the
Owner’s Information section of this manual.
DO NOT USE this appliance if any part has been under
water. Immediately, CALL a qualified service technician
to inspect the unit and to replace any part of the control
system and any gas control that has been under water.
THIS UNIT IS NOT FOR USE WITH SOLID FUEL.
This unit MUST be used with a vent system as
described in this installation manual. NO OTHER vent
system or components MAY BE USED.
This gas fireplace and vent assembly MUST be vented
directly to the outside and MUST NEVER be attached
to a chimney serving a separate solid fuel burning
appliance. Each gas appliance MUST USE a separate
vent system. Common vent systems are PROHIBITED.
INSPECT the external vent cap on a regular basis to
make sure that no debris, plants, trees, shrubs are
interfering with the air flow.
Installation and repair should be PERFORMED by a
qualified service person. The appliance and venting
system should be INSPECTED before initial use and at
least annually by a professional service person. More
frequent cleaning may be required due to excessive
lint from carpeting, bedding, etc. It is IMPERATIVE that
the unit’s control compartment, burner, and circulating
air passageways BE KEPT CLEAN to provide for
adequate combustion and ventilation air.
The glass door assembly MUST be in place and sealed
before the unit can be placed into safe operation.
Always KEEP the appliance clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
If the barrier becomes damaged, the barrier SHALL BE
REPLACED with the MANUFACTURER’S BARRIER
for this appliance.
NEVER OBSTRUCT the flow of combustion and
ventilation air. Keep the front of the appliance CLEAR
of all obstacles and materials for servicing and proper
operation.
DO NOT USE abrasive cleaners on the glass door
assembly. DO NOT ATTEMPT to clean the glass door
when it is hot.
Due to the high temperature, the appliance should be
LOCATED out of traffic areas and away from furniture
and draperies. Clothing or flammable material SHOULD
NOT BE PLACED on or near the appliance.
DO NOT OPERATE this appliance with the glass door
removed, cracked, or broken. Replacement of the glass
door should be performed by a licensed or qualified
service person. DO NOT strike or slam the glass door.
The glass door assembly SHALL ONLY be replaced
as a complete unit, as supplied by the fireplace
manufacturer. NO SUBSTITUTE material may be used.
TURN OFF the gas before servicing this appliance.
It is recommended that a qualified service technician
perform an appliance check-up at the beginning of each
heating season.
Clothing or flammable material SHOULD NOT BE
PLACED on or near the appliance.
Any safety screen, guard or barrier removed for servicing the appliance, MUST BE REPLACED prior to
operating the appliance.
Children and adults should be ALERTED to the hazards
of high surface temperature and should STAY AWAY to
avoid burns or clothing ignition.
DO NOT place furniture or any other combustible
household objects within 36” of the fireplace front.
YOUNG CHILDREN should be CAREFULLY
SUPERVISED when they are in the same room as
the appliance. Toddlers, young children and others
may be susceptible to ACCIDENTAL CONTACT
BURNS. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access
to a fireplace or stove, INSTALL AN ADJUSTABLE
SAFETY GATE to keep toddlers, young children and
other at risk individuals out of the room and away from
hot surfaces.
BE CAREFUL not to put any decorating objects
sensitive to heat to close above or around the fireplace
as it gets very hot when operating.
DO NOT use this heater as a temporary source of heat
during construction.
This appliance is a DOMESTIC ROOM-HEATING APPLIANCE. It must not be used for any other purposes
such as drying clothes, etc.
State of California. Proposition 65 Warning. Fuels
used in gas, wood-burning or oil fired appliances,
and the products of combustion of such fuels, contain
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6.
3
!
Safety and Your Fireplace
Safety and Your Fireplace
Please Read and Carefully Follow all Safety Warnings and
Operating Instructions Contained in Your Owners Manual
(Replacement Manuals are available by contacting our service department at
1-800-468-2567 or visit www.valorfireplaces.com).
skills and response reflexes to
withdraw in the event of accidental
contact with a hot surface.
Please Follow These Important
Child Safety Precautions and
Recommendations,
•
Parts of your Valor Fireplace become
extremely hot while in operation.
•
The glass viewing window
temperature can
exceed 500 F
at full capacity.
Momentary contact
with a hot glass
surface can cause
a severe burn, even if the fireplace
is operating at reduced heating
capacity.
•
•
4
The glass window will remain hot
for an extended period of time after
the fireplace has been turned off.
Ensure that children are prevented
from touching the fireplace during the
cool down period.
Toddlers and Young Children
must be closely supervised at all
times when they are in the same
room as the operating fireplace. They
lack full awareness of danger and
rely on your protection. Toddlers,
in particular, do not have the motor
•
A physical barrier is strongly
recommended if there are young
children, or at-risk individuals in the
house. Install an approved aftermarket safety gate to keep toddlers,
young children and other at-risk
individuals a safe distance from the
fireplace.
•
Keep the remote control handset
out of reach of children at all
times. A wall mount storage holster
is provided with your remote control
handset.
•
Ensure that the fireplace, including
the pilot light, is completely turned
off when children are present and
close supervision and safety barriers
are not available—see page 9 of
Owner’s Information section.
•
If the fireplace is not going to be used
for the summer or any extended
period of time, remove the batteries
from the remote control handset
and receiver. It is recommended that
batteries are replaced annually in any
event—see page 8.
Owner’s Information
! WARNING
EXTREMELY HOT!!!
• READ the SAFETY information on pages
3 and 4 of this manual BEFORE operating
your gas heater.
• Some parts of your fireplace are EXTREMELY
HOT, particularly the GLASS window.
• DO NOT LET CHILDREN touch the glass or
any parts of your fireplace even after it is
turned off as it is still hot.
• USE THE BARRIER SCREEN PROVIDED
WITH THE APPLIANCE OR STOVE CASING
or a GATE to reduce the risk of burns.
• Keep the remote control handset OUT OF
REACH of children.
• HOT HEARTH / FLOOR! The hearth or floor
in front of the fireplace may become very hot
when the fireplace heats. Do not use the hearth
as a seat or shelf.
• Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fireplace.
AVOID PLACING candles, paintings, photos,
and other items SENSITIVE TO HEAT within
36 inches (0.9 m) around the fireplace.
• Solid wood flooring in front of the fireplace (if
allowed) may shrink during the heating season
due to heat.
Performance of LPG appliances may be affected
by the quality of commercial gas supplied in
your area.
Fireplace
Hearth
Do not put
furniture or other objects
in this space in front of
the fireplace:
36” (0.9 m)
OWNER’S
INFORMATION
Thank You ...
For purchasing a Valor by Miles Industries. Your new
radiant gas heater is a technical appliance that must
be installed by a qualified dealer. Each Valor fireplace
is fully tested during the production process for your
safety and comfort.
Your unit has been professionally installed by:
Dealer Name: ________________________________
Phone Number :_______________________________
Should you encounter an operational problem, call
your dealer immediately.
Do not try to repair the unit as you may cause an
injury or damage the fireplace.
This manual and particularly the preceeding
and following pages contain very important
information regarding the safe operation of your
fireplace as well as maintenance instructions.
Read carefully BEFORE operating your fireplace
and pay special attention to the SAFETY
WARNINGS.
A heating gas appliance does require safe handling
and for this reason, we very strongly recommend that
no children be allowed to touch the fireplace and its
controls at all times. Do install a screen or barrier
in front of the fireplace to protect your children
against severe burns.
Operating Your Stove for the First Time
When operating your new fireplace for the first time,
some vapors may be released due to the burning of
curing compounds used in the manufacture of the
appliance. They may cause a slight odor and could
cause the flames to be the full height of the firebox, or
even slightly higher, for the first few hours of operation.
It is also possible that these vapors could set off any
smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room. After
a few hours use, the vapors will have disappeared and
the flames will be at their normal height.
Flame Supervision Device
For your safety, this appliance is fitted with a flame
supervision device which will shut-off the gas supply
if, for any reason, the pilot flame goes out. This device
incorporates a fixed probe, which senses the heat
from the pilot flame. If the probe is cool, the device will
prevent any gas flow unless manually lighting the pilot.
See full lighting instructions on page 15 of this manual.
5
OWNER’S
INFORMATION
Owner’s Information
Cleaning the Window
! WARNING
DO NOT TOUCH THE GLASS WHILE IT IS HOT!
Let the stove cool first before cleaning it.
Important - Glass cleaning - Mineral deposits
One of the by-products of the combustion process in
a gas appliance is a mineral which can show up as a
white film on the ceramic glass of the viewing door.
The composition of the deposit varies widely with
location and time. It is believed to be associated with
the varying sulfur content of the gas. You may have the
problem intermittently.
We have consulted with ceramic glass manufacturers
and they cannot offer a definitive solution to this
problem. Dealers have tried various cleaning products
with varying results. The following are recommendations
only and are not meant to guarantee results.
NOTE: This is a problem beyond Miles Industries’
control and is not covered under warranty.
• Clean the glass regularly as soon as you notice
the buildup (white film). If the film is left for a longer
period of time, it will bake on. It is then much harder,
if not impossible, to remove.
• NEVER use an abrasive cleaner on the ceramic
glass. Any abrasion of the surface has the
immediate effect of compromising the strength of the
glass. An emulsion type cleaner is recommended.
• Use a soft damp cloth to apply the cleaner. Dry the
glass with a soft, dry, preferably cotton cloth. Most
paper towels and synthetic materials are abrasive to
ceramic glass and should be avoided.
• Our dealers have had good results from the
products listed below. We cannot, however,
guarantee the results of these products.
» BRASSO, POLISH PLUS by KELKEM, COOK TOP CLEAN
CREME by ELCO, WHITE OFF by RUTLAND, TURTLE WAX
To remove the window for cleaning:
1. Traditional stove MFCS01 and MFCS02: Remove
the barrier screen by pulling it on each side and then
unhooking the top clip.
Contemporary stove MFCS04: Pull out the top of
the screen and then lift it up to unhook the bottom.
2. Traditional stove MFCS01 and MFCS02: Unhook
the cast front.
Contemporary stove MFCS04:
a) Remove the window frame cover.
b) Remove the concrete cast shelf (opening the
access door under the shelf may help).
c) Remove the upper columns first pulling them up,
off their bottom bracket, and then pulling them
out unclipping them from the side panels.
1. Remove barrier screen
2. Remove window frame cover
3. Remove cast concrete shelf
4. Remove upper side columns
starting at the top
4
4
2
1
3
3. Rotate the four fastening studs of the window 90
degrees to release them and gently pull the window
unit outwards. Set aside in a safe place to avoid
damage.
Do not clean the glass while it is hot!
Always securely replace the window and the barrier
screen before lighting.
If broken, the glass pane may only be replaced
as a complete window unit as supplied by the
manufacturer.
If the barrier becomes damaged, the barrier shall
be replaced with the manufacturer’s barrier for this
appliance.
6
x4
OWNER’S
INFORMATION
Owner’s Information
To refit the window:
1. Place it on its frame and hold it in place while
pushing and turning its fastening studs 90 degrees.
IMPORTANT: To ensure a safe operation, verify
that the bolts are hooked properly to the window
tabs; then, pull out the top of the window and
release it to insure the springs return it.
Then, apply light hand pressure against the window
frame sides to bed-in the window seal.
2. If the Hot Glass Warning plate has been removed
from the front lower corner of the window,
reinstall it by sliding it between the glass and
the frame as indicated.
Hot Glass Warning Plate
3. Traditional stove MFCS01 and MFCS02: Re-hook
the cast front.
Contemporary stove MFCS04:
a) Re-install the upper side columns on each side
of the window fitting the bottom first and then
pushing in squarely sliding the spring clips on the
inside edge of the side panels.
b) Re-insert the concrete cast shelf between the
upper and lower columns. Close the access door
if opened.
c) Re-hook the window frame cover to the window’s
spring-loaded top bolts.
4. Traditional stove MFCS01 and MFCS02: Re-install
the barrier screen by inserting first the top clip in the
arch of the front and then pushing on the side of the
screen so that the clips snap into place.
Contemporary stove MFCS04: Re-install the
barrier screen by hooking first the lower brackets
to the inside edge of the concrete shelf and then
pushing the screen against the stove so the upper
clips snap on the upper side columns.
Cleaning the Stove
Barrier screens
The barrier screens can be brushed clean.
! WARNING
FOR SAFETY PURPOSE, ensure the barrier
screen is re-installed on the stove front after
maintenance.
Cast iron stove body
The matte cast iron stove body can be brushed clean.
The enameled cast iron stove body can be cleaned with
mild soap and water then dried with a lint-free soft cloth.
Cast concrete stove body
Dust down the surface regularly with a soft brush and
occasionally follow up with a wipe over with a wet cloth.
A sealer has been applied to the concrete surface, no
cleaning agents nor polishes should be used. In case
of an accidental spill, soak up the liquid IMMEDIATELY
with a dry cloth and follow up with a wipe down with a
wet cloth.
Logs and burner
Dust can be brushed from the ceramic logs and firebox
walls after removing the front unit and opening the window. Dust can also be removed from the burner using
a soft brush after removing the ceramic logs. When
cleaning, make sure that no particles are brushed into
the slots of the burner.
Checks
A periodic check of the pilot and burner flames should
be made. Check after the fire has been on for at least
30 minutes. The pilot flame must cover the tip of the
thermocouple probe. The main burner flame pattern will
vary from appliance to appliance depending on the type
of installation and climatic conditions.
Correct Flame Picture
Pilot Flame can be seen
between left front and top logs
! WARNING
DO NOT TOUCH THE STOVE WHILE IT IS
HOT! Let the stove cool first before cleaning it.
Pilot
flame
Thermocouple
probe must be
in flame
Thermocouple
probe must be
in flame
7
OWNER’S
INFORMATION
Owner’s Information
The appliance area must always be kept clear and
free from combustible materials, gasoline and other
flammable vapors and liquids.
Inspect the vent terminal outdoors regularly to make
sure that snow, trees, bushes, leaves, or other objects
do not obstruct it.
Examine the vent system and terminal regularly. We
recommend annually.
Remote Control Handset Wall Holder
Your fireplace equipment includes a wall
holder to store the handset. If it hasn’t be
installed, refer to the instructions further
on in this manual for the installation.
Batteries
! WARNING
DO NOT ATTEMPT TO CHANGE THE BATTERIES WHILE THE FIREPLACE IS STILL HOT! Let
the fireplace cool first before touching it.
CAUTION
DO NOT USE a screwdriver or other metallic
object to remove the batteries from the battery box
or the handset! This could cause a short circuit.
Low battery signal: see page 14.
BEFORE changing the batteries, turn off the valve
using the switch’s On/Off button.
The appliance uses four 1.5 V AA alkaline batteries
for its remote control receiver and one 9 V alkaline
battery for its handset. Batteries should last one to two
seasons, depending on usage. Removing the batteries
in the off-season will extend the battery life. Should
the batteries lose power, the control may be operated
by manually turning the control knob at the valve or by
turning off the valve at the switch.
To replace the batteries in the remote control
receiver:
1. The receiver is located to the left of the valve and
it is clipped to the casting’s cross beam. Unclip the
receiver from the cross beam.
2. Slide and remove the receiver cover.
3. Replace the batteries with 4 AA alkaline batteries.
4. Replace the cover.
5. Clip the receiver back to the cross beam.
unit MFCS01, use the Stove Bright by Forrest 1990
Satin Black spray paint. Please note that it may be
necessary to spray the entire cast piece.
Lighting, Operation and Rating Information
The Lighting, Operation and Rating information is
located on the rear of the appliance casing.
! WARNING
DO NOT ATTEMPT TO TOUCH THE DATA PLATE
WHILE THESTOVE IS STILL HOT! Let the stove
cool first before touching it.
To access the plate, reach over the top of the stove
and pull the plate out from its holder to read it. There is
important information on both sides of the plate.
Servicing
If any attention is required for your appliance, contact
your supplier quoting the model number. It will be
helpful if the appliance serial number can also be
quoted. This number is on the rating plate, which is
attached to the unit. The replacement parts are shown
at the end of this manual. Please always quote the part
number and description when requesting spare parts.
Fireplace Control Devices
There are three ways to control your fireplace.
1. Thermostatic Remote Control;
2. Wall Switch;
3. Manual On/Off Switch.
The manual On/Off switch must be ON for the fireplace
to function. It can be used to shut off the fireplace in
case of emergency—see above.
The Thermostatic Remote Control can be programmed
to function automatically—see pages 10–14.
The Wall Switch (optional) can be used to turn on, off
and to increase or decrease the flame height—see
1265WSK—Wall Switch Kit.
NOTE: The remote control in the AUTO mode will
override the wall switch.
How to Turn Your Fireplace OFF
Touch Up Paint
ON
If you need to touch up the paint on your matte cast
OFF
Thermostatic Remote
Control
8
Wall Switch
(optional)
Manual On/Off Switch
Owner’s Information
OWNER’S
INFORMATION
(including pilot)
Be Turned ON Inadvertently
Familiarize yourself with each of these methods before
operating your fireplace.
You can use one of the two following methods to
ensure that your fireplace will not turn on when you
don’t want it on.
Handset and Wall Switch: Press and hold the OFF
button for a second (either on the handset or the wall
switch).
If the flames are on, they go down and you hear the
valve motor wind down. You hear a clunk and a beep
indicating that the valve has received the signal from
the remote control.
Manual ON/OFF Switch: Press the O button.
First, ensure your fireplace is turned off—including
the pilot—and cold BEFORE going ahead.
• You can prevent your fireplace from lighting by
pressing the O button on the manual ON/OFF switch
on the gas valve—see image above.
• Alternately, remove all batteries from the receiver as
well as the battery from the handset.
Automatic Shut-Off (in certain conditions)
Your fireplace’s remote control is equipped with an
automatic shut-off mechanism which is activated in
certain conditions. See page 14 in the Remote Control
Operation section for a description of this feature.
Thermostatic
Remote Control
Wall Switch
(optional)
How to Ensure Your Fireplace Cannot
Traditional Stove
MFCS01 or MFCS02
Contemporary Stove
MFCS04
ON
OFF
Manual On-Off Switch
9
OWNER’S
INFORMATION
Remote Control Operation
NOTE: Before using the remote control system for
the first time, the receiver and the handset must be
synchronized. See the section Remote Control Initial
Set-up on page 33 of this manual.
Current
temperature
(F or C)
IMPORTANT: BEFORE YOU BEGIN, please note that
on this system, the settings of time, temperature and
automatic ON/OFF can only be programmed when
the function display is flashing. Be patient when
programming as it can take a few seconds to set.
Handset
sensor
Period
start or end
(Temp, Timer)
Battery status
Current time
(12 or 24 hour clock)
Current
programmed
period (Timer)
Modes (Manual,
Temperature, Timer)
Display Overview
Note: In the TEMP or TIMER modes, the remote
handset senses the room temperature and adjusts the
flame accordingly.
To communicate, the handset should be within 15 feet
(4.5 meters) of the fireplace.
Do not leave the handset on the mantel or hearth.
TO TURN ON APPLIANCE
CAUTION
When pilot ignition is confirmed, motor turns
automatically to maximum flame height.
Large flame
button (flames
up, sets hours,
temperature)
Set (scrolls
through
modes and
settings)
OFF (returns
to set mode,
turns the burner
and the pilot off )
Small flame
button (flames
down and off,
sets minutes,
temperature)
Handset Overview
TO TURN OFF APPLIANCE
•
• On the valve, turn MAN knob on the ON, full
counterclockwise
position.
• Place ON/OFF switch (if equipped) in I (ON
position).
•
Simultaneously press the OFF and
(large flame) buttons until a short
beep confirms the start sequence
has begun; release buttons.
• Continuing beeps confirm the
ignition is in process.
• Once pilot ignition is confirmed,
there is main gas flow.
• After main burner ignition the
handset will automatically go into
manual (MAN) control mode.
10
Press OFF button.
When the pilot is off, it will take 2
When the
pilotitiscan
off, be
it will
take 2
minutes
before
lit again.
minutes before it can be lit again.
STANDBY MODE (Pilot Flame)
• Press and hold
(small flame) to set appliance at
pilot flame.
FLAME HEIGHT ADJUSTMENT
•
In standby mode: Press and hold
(large flame) button to increase
flame height.
OWNER’S
INFORMATION
Remote Control Operation
• Press and hold
(small flame)
button to decrease flame height or
to set the appliance at pilot flame.
• For fine adjustment tap the
(large flame) or (small flame)
buttons.
Express Low and High Fire
• Double-click
(small flame)
button. “LO” will be displayed.
NOTE: Flame goes to high fire first
before going to designated low fire.
MODES OF OPERATION
• Briefly pressing the SET button
changes the mode of operation in
the following order:
MAN
TEMP
TEMP →
→
→
TIMER
→ and back to
MAN
.
NOTE: Manual mode can also be reached by pressing
either the
(large flame) or the (small
flame) buttons.
•
- Manual Mode - Manual
Flame Height Adjustment.
•
- Daytime Temperature Mode (Appliance must be in
standby mode; pilot ignited) - The
room temperature is measured and
compared to the set temperature.
The flame height is then automatically adjusted to achieve the
Daytime Set Temperature.
•
- Nighttime Setback
Temperature Mode (Appliance
must be in standby mode; pilot
ignited) - The room temperature
is measured and compared to the
Nighttime Setback temperature.
The flame height is then automatically adjusted to achieve the Nighttime Setback Temperature.
•
- Timer Mode (Appliance
must be in standby mode; pilot
ignited) - The timers P1 and P2
(Program 1, Program 2) each can
be programmed to go ON and OFF
at specific times. For instructions
see Timer Programming Mode.
MAN
x2
• Double-click
(large flame)
button. Flame automatically goes
to high fire. “HI” will be displayed.
x2
SETTING ºC/24-HOUR OR ºF/12-HOUR CLOCK
• In MAN mode, press OFF and
(small flame) buttons until display
changes from Farenheit/12-hour
clock to Celsius/24-hour clock and
vice versa.
SETTING THE TIME
• The time display will flash after
either:
» Installing the battery or
» Simultaneously pressing the
(large flame) and
(small flame)
buttons.
• Press
(large flame) button to
set the hour.
• Press
(small flame) button to
set the minute.
• Press OFF or simply wait to return
to MAN mode.
TEMP
TEMP
TIMER
NOTE: The display shows the set temperature every
30 seconds.
11
OWNER’S
INFORMATION
Remote Control Operation
SETTING THE ON / OFF TEMPERATURES
SETTING THE “DAYTIME” TEMPERATURE
Default Settings:
•
TEMP
(sun), 23ºC / 74ºF
SETTING THE “NIGHTTIME SETBACK”
TEMPERATURE
Default Settings:
Briefly press SET button to scroll to
TEMP
TEMP
(sun) mode. Hold
the SET button until the TEMP
flashes.
TEMP
(moon), “--” (OFF)
• Briefly press SET button to scroll to
TEMP T E M P (moon) mode. Hold
the SET button until the TEMP
flashes.
• Press
(large flame) button
to increase the
Daytime Set
Temperature.
• Press
(large flame) button to
increase
Nighttime Setback
Temperature.
• Press
(small flame) button
to decrease
Daytime Set
Temperature.
• Press
(small flame) button to
decrease
Nighttime Setback
Temperature.
• Press OFF or simply wait to
complete programming.
• Press OFF or simply wait to
complete programming.
Tip
Set the different parameters when they are flashing.
12
OWNER’S
INFORMATION
Remote Control Operation
SETTING PROGRAM TIMERS
SETTING P1 OFF TIME
• You can program two periods of time between 12:00
am and 11:50 pm in each 24-hour cycle.
• The Programs P1 and P2 must be set in the
following order during a 24-hour cycle: P1 , P1 ,
P2
and P2 .
• The icon
indicates the beginning of the period (ON)
and the icon indicates the end of the period (OFF).
• If P1 = P1 or P2
= P2 , the programming
is cancelled.
• To keep the fireplace ON all night, set P2 at
11:50 am and P1
at 12:00 am.
•
Briefly press SET button to scroll
to TIMER P1 (moon) while the
time flashes.
•
Press
(large flame) button to set
the hour.
•
Press
(small flame) button to
set the minutes.
Default settings:
Program 1: P1
Program 2: P2
6:00 am P1
11:50 pm P2
8:00 am
11:50 pm
• Briefly press SET button to scroll to
TIMER mode.
SETTING P1 ON TIME
• Hold the SET button until P1
(sun) is displayed and the time
flashes.
SETTING P2 ON TIME
• Briefly press SET to scroll to TIMER mode P2
(sun) while the time flashes.
• Follow the instructions given to set P1 ON time.
SETTING P2 OFF TIME
• Press
(large flame) button to
set the hour.
• Briefly press SET to scroll to TIMER mode P2
(moon) while the time flashes.
• Follow the instructions given to set P1 OFF time.
Press OFF button to save these settings. The timers
are programmed. See the diagram on programming
sequences on the following page.
• Press
(small flame) button to
set the minutes.
Tip
If you want to program only one period, program P1
and P1 with desired times and program P2
and
P2
P1
with the same time as
.
13
OWNER’S
INFORMATION
Remote Control Operation
Timer Programming Example (default temperatures shown)
6:00 a.m.—
P1
Start time
☼
Set temp
4:00 p.m.—
P2
Start time
8:00 a.m.—
P1 ☽
End time
☼
74˚F
Set temp
10:00 p.m.—
P2 ☽
End time
☼
☽
40˚F
AUTOMATIC TURN DOWN
Set temp
☼
74˚F
Set temp
6:00 a.m.—
P1
Start time
☼
☽
40˚F
LOW BATTERY INDICATION
• No communication. If there is no communication
between the receiver and the handset for a period of
6 hours, the appliance goes into pilot mode.
• No change in flame height. If there is no change
in flame height for a period of 6 hours, the appliance
goes into pilot mode.
NOTE: In TEMP or TIMER modes, the flame height
will vary according to room temperature. The appliance will continue to work normally. However, if the
room temperature remains the same for 6 hours, the
appliance will go into pilot mode.
AUTOMATIC SHUT OFF
• Low batteries in the receiver. With low battery
power in the receiver the system shuts off
completely.
NOTE: This does not apply when the power supply
is interrupted.
• No change in pilot. The appliance shuts off
completely when it is continually in pilot position—
without any change—for a period of 5 days.
CAUTION
DO NOT USE a screwdriver or other metallic object
to remove the batteries from the battery box or the
handset! This could cause a short circuit.
Remote handset: The battery icon
will show
when the battery needs to be replaced.
Replace with one 9 V alkaline battery.
Receiver: Three short ‘beeps’ will sound when the
motor turns when the batteries need to be replaced.
Replace with four 1.5 V alkaline batteries.
HANDSET / RECEIVER MATCH
The remote control handset and receiver are programmed to function together. In case of a replacement of
the handset or the receiver, you will need to reset the
receiver to allow them to function together. Contact your
dealer for details.
Options
Required Kits*
Optional Kits*
Stove Casing (choose one)
MFCS01—Traditional Madrona Stove Black with
Barrier Screen 4003311
MFCS02—Traditional Madrona Stove Majolica Brown
with Barrier Screen 4003311
MFCS04—Contemporary Madrona Stove with Barrier
Screen 4003433
Venting
See venting accessories listed on pages 36–37.
1265WSK—Wall Switch Kit
555CFK—Circulating Fan Kit
MA28IPK—Conversion Kit to Propane Gas
MA28INK—Conversion Kit to Natural Gas
14
Hearth Gate
Hearth gates such as Cardinal’s VersaGates are
available at retail stores carrying safety products
for children.
*Information accurate at the time of printing and subject to
change without notice.
Lighting Instructions
OWNER’S
INFORMATION
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactlyD¿UHRUH[SORVLRQPD\UHVXOWFDXVLQJ
SURSHUW\GDPDJHSHUVRQDOLQMXU\RUORVVRIOLIH
A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly. To
save gas, turn the pilot off when not using the appliance for a prolonged period of time.
%%()25(/,*+7,1*VPHOODOODURXQGWKHDSSOLDQFHDUHDIRUJDV%HVXUHWRVPHOOQH[WWRWKHÁRRUEHFDXVHVRPHJDV
DUHKHDYLHUWKDQDLUDQGZLOOVHWWOHRQWKHÁRRr.
WHAT TO DO IF YOU SMELL GAS
‡'RQRWWU\WROLJKWDQ\DSSOLDQFH
‡'RQRWWRXFKDQ\HOHFWULFVZLWFKGRQRWXVHDQ\SKRQHLQ\RXUEXLOGLQJ
‡,PPHGLDWHO\FDOO\RXUJDVVXSSOLHUIURPDQHLJKERr’s phone. Follow the gas supplier’s instructions.
‡,I\RXFDQQRWUHDFK\RXUJDVVXSSOLHrFDOOWKHÀUHGHSDUWPHQW
C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by hand,
GRQ·WWU\WRUHSDLUWKHPFDOODTXDOLÀHGVHUYLFHWHFKQLFLDQ)RUFHRUDWWHPSWHGUHSDLUPD\UHVXOWLQDÀUHRUH[SORVLRQ
D. Do not use this appliance if any part has been under water,PPHGLDWHO\FDOODTXDOLÀHGVHUYLce technician to inspect
the appliance and to replace any part of the control system and any gas control, which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above. Dependent on model, switch #1 may be mounted directly to valve see Fig 2A.
)LJ
)LJ
)LJ$
2. SET ON/OFF SWITCH (1) TO “OFF” POSITION.
‡ WDLWÀYHPLQXWHVWRFOHDURXWDQ\JDVWKHQVPHOOIRUJDVLQFOXGLQJQHDUWKHÁRRr. If you smell gas, STOP! Follow
“B” in the safety information above on this label. If you don’t smell gas, go to the next step.
3. AUTOMA7,&,*1,7,21ÀJ/RFDWHWKHSLORWÀJLQVLGHRIÀUHER[DW/HIW+DQGVLGH
‡ 212))VZLWFKLQ21SRVLWLRQ0$1NQRELQ21SRVLWLRQVHW)ODPH Adjustment knob (3) to lowest setting
(3);
(large flame) VLPXOWDQHRXVO\DVKRUW
‡ On the remote control handset, press and hold the ‘off ’ button and
DFRXVWLFVLJQDOFRQÀUPVWKHVWDUWKDVEHJXQ
‡ )XUWKHUVKRUWDFRXVWLFVLJQDOVLQGLFDWHWKHLJQLWLRQSURFHVVLVLQSURJUHVV
‡ When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to the highest setting.
‡ Press the (small flame)RQWKHUHPRWHFRQWUROKDQGVHWWRUHGXFHWKHÁDPHKHLJKW
4. MANUAL,*1,7,21ÀJWLWKWKHZLQGRZRIIORFDWHWKHSLORWÀJ
LQVLGHRIÀUHER[DW/HIW+DQGVLGH
‡ 212))VZLWFKLQ21SRVLWLRQ0$1NQRELQ0$1SRVLWLRQ
‡ Set Flame Adjustment knob (3) to the lowest setting (3);
)LJ
‡ 3XVKGRZQWKHPHWDOOLFFRUHZLWKDSHQRUVLPLODULQVWUXPHQWWKLVZLOOHVWDEOLVKWKHSLORWJDVÁRZ
/LJKWJDVDWWKHSLORWZLWKDPDWFK
&RQWLQXHKROGLQJGRZQPHWDOFRUHIRUDERXWVHFRQGVDIWHUUHOHDVHSLORWVKRXOGUHPDLQOLW
‡
If the pilot will not stay lit after several tries, turn the gas control knob (3) to “OFF” (3) and call your local
service technician or gas supplier.
5HLQVWDOOWKHZLQGRZDQGVHWWKH0$1NQREWR´21µWXUQ)ODPH Adjustment knob (3) up (4) or down
manually or use the up/down ‘flame’ buttons on the remote control handset to adjust theÁDPHKHLJKW
TO TURN OFF GAS TO APPLIANCE
1. AUTOMATIC SHUT2))XVLQJWKHUHPRWHFRQWUROKDQGVHW
X
(small flame) RQWKHUHPRWHFRQWUROKDQGVHWWRVKXWRIIWKHPDLQEXUQHUJDVÁRZ
‡ Press and hold the
‡ 3UHVV´2))µEXWWRQRQUHPRWHKDQGVHWWRVKXWRIIWKHDSSOLDQFHLQFOXGLQJSLORWÁDPH
2. MANUAL SHUT-OFF (using only the ON/OFF switch (1))
‡ Press “O” the ON/OFF switch (1) to shut-off the appliance.
15
OWNER’S
INFORMATION
Commonwealth of Massachusetts
State of Massachusetts Carbon Monoxide
Detector/Vent Terminal Signage
Requirements
For all side wall horizontally vented gas fueled
equipment installed in every dwelling, building or
structure used in whole or in part for residential
purposes, including those owned or operated by the
Commonwealth and where the side wall exhaust
vent termination is less than seven (7) feet above
finished grade in the area of the venting, including
but not limited to decks and porches, the following
requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE
DETECTORS. At the time of installation of the side wall
horizontal vented gas fueled equipment, the installing
plumber or gas fitter shall observe that a hard wired
carbon monoxide detector with an alarm and battery
back-up is installed on the floor level where the gas
equipment is to be installed. In addition, the installing
plumber or gas fitter shall observe that a battery
operated or hard wired carbon monoxide detector
with an alarm is installed on each additional level of
the dwelling, building or structure served by the side
wall horizontal vented gas fueled equipment. It shall
be the responsibility of the property owner to secure
the services of qualified licensed professionals for the
installation of hard wired carbon monoxide detectors.
a. In the event that the side wall horizontally vented
gas fueled equipment is installed in a crawl space or
an attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next
adjacent floor level.
b. In the event that the requirements of this subdivision
can not be met at the time of completion of installation,
the owner shall have a period of thirty (30) days
to comply with the above requirements; provided,
however, that during said thirty (30) day period, a
battery operated carbon monoxide detector with an
alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS.
Each carbon monoxide detector as required in
accordance with the above provisions shall comply
with NFPA 720 and be ANSI/UL 2034 listed and IAS
certified.
16
3. SIGNAGE. A metal or plastic identification plate
shall be permanently mounted to the exterior of the
building at a minimum height of eight (8) feet above
grade directly in line with the exhaust vent terminal for
the horizontally vented gas fueled heating appliance
or equipment. The sign shall read, in print size no less
than one-half (1/2) inch in size, “GAS VENT DIRECTLY
BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of
the side wall horizontally vented gas fueled equipment
shall not approve the installation unless, upon
inspection, the inspector observes carbon monoxide
detectors and signage installed in accordance with the
provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt
from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled
“Equipment Not Required To Be Vented” in the most
current edition of NFPA 54 as adopted by the Board;
and
2. Product Approved side wall horizontally vented
gas fueled equipment installed in a room or structure
separate from the dwelling, building or structure used in
whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS
EQUIPMENT VENTING SYSTEM PROVIDED.
When the manufacturer of Product Approved side
wall horizontally vented gas equipment provides a
venting system design or venting system components
with the equipment, the instructions provided by the
manufacturer for installation of the equipment and the
venting system shall include:
1. Detailed instructions for the installation of the venting
system design or the venting system components; and
2. A complete parts list for the venting system design or
venting system.
Commonwealth of Massachusetts
OWNER’S
INFORMATION
(d) MANUFACTURER REQUIREMENTS - GAS
EQUIPMENT VENTING SYSTEM NOT PROVIDED.
When the manufacturer of a Product Approved side
wall horizontally vented gas fueled equipment does
not provide the parts for venting the flue gases, but
identifies “special venting systems”, the following
requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions
shall be included with the appliance or equipment
installation instructions; and
2. The “special venting systems” shall be Product
Approved by the Board, and the instructions for that
system shall include a parts list and detailed installation
instructions.
(e) A copy of all installation instructions for all Product
Approved side wall horizontally vented gas fueled
equipment, all venting instructions, all parts lists
for venting instructions, and/or all venting design
instructions shall remain with the appliance or
equipment at the completion of the installation.
17
QUALIFIED
INSTALLER
Specifications
Approval & Codes
This appliance is certified to ANSI Z21.88a-2012/
CSA 2.33a-2012 American National Standard / CSA
Standard for Vented Gas Fireplace Heaters for use in
Canada and USA, and to CGA 2.17-91 High Altitude
Standard in Canada. This appliance is for direct vent
installations.
Conversion between fuels may only be done using
the approved conversion kits listed on page 14. This
appliance complies with CSA P4.1-09 Testing method
for measuring annual fireplace efficiencies.
The installation must conform to local codes or, in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1 or the Natural Gas and Propane
Installation Code CAN/CGA-B149. Only qualified
licensed or trained personnel should install this
appliance.
This appliance, when installed with the optional
circulating fan kit (blower), must be electrically
grounded in accordance with local codes, or, in the
absence of local codes, with the National Electrical
Code, ANSI/NFPA 70 or the Canadian Electrical Code,
CSA C22.1.
Ratings
Model (Field convertible Top MF28JLN MF28JLP
or Rear Vent Outlet)
Gas
Natural
Propane
Altitude (Ft)*
0-4,500 feet*
Input Maximum (Btu/h)
26,000
26,000
Input Minimum (Btu/h)
6,500
14,500
Manifold Pressure (in w.c.)
3.75
9.0
Minimum Supply Pressure
5.0
11.0
(in w.c.)
Maximum Supply Pressure
11.0
14.0
(in w.c.)
Main Burner Injector Marking 82-750
92-300
Pilot Injector Marking
35
27
For installations at elevations above 4,500 feet
(1,370 m) in Canada, please consult provincial
and/or local authorities having jurisdiction.
Supply Gas
Heater engine MF28JLN is used with natural gas.
Heater engine MF28JLP is used with propane gas.
The supply pressure must be between the limits
shown in the Ratings section above.
The supply connection is 3/8” NPT female.
5/16” O.D.
tubing
5/16”
flare
3/8” N.P.T.
Female
3/8” N.P.T.
Electrical
The Madrona stove does not require an electrical
power source unless it is fitted with an optional
circulating fan—see page 14.
Hearth Requirements
This unit is approved for mounting directly on
combustible wood flooring. If installed directly on
carpeting, vinyl or soft combustible floor other than
wood, it must be installed on a metal or wood panel
covering a minimum surface of 15 inches deep by
28 inches width.
Madrona Stoves
There are two types of stove casing for the Madrona
MF28J engine, a traditional style available in two colors
and a contemporary style. The stove casings are sold
separately.
MFCS01—Traditional Stove Black
MFCS02—Traditional Stove Majolica Brown
MFCS04—Contemporary Stove
*High Altitude Installations
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to 4,500 feet
(1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the current
ANSI Z223.1 and/or local codes having jurisdiction.
Heating value of gas in some areas is reduced to
compensate for elevation—consult your local gas
utility to confirm.
18
Traditional Stove
MFCS01 or MFCS02
Contemporary Stove
MFCS04
QUALIFIED
INSTALLER
Dimensions & Clearances
Traditional Cast Stove MFCS01 (black) or Traditional Cast Stove MFCS02 (Majolica brown)
2” (52 mm)
4”
minimum (102 mm)
Suggested gas line
access point through wall.
Route to avoid optional fan.
17-7/8” (454 mm)
Ø 6-5/8”
venting
Mantel / shelf clearances
Pipe supplied with
engine (see engine
manual p. 18)
Mantel
0–1”
2–5”
6–18”
19–24”
Depth ‘A’ (0–26 mm) (51–127 mm) (152–457 mm) (483–610 mm)
Mantel
34”
36”
38”
42”
Height ‘B’ (864 mm)
(914 mm)
(965 mm)
(1067 mm)
x
Gas line connection point
3/8” NPT FEMALE at valve
2”
(52 mm)
minimum
A
Sidewall
Supplied with
top vent; field
convertible to
rear vent
Mantel
28-1/2 ” (724 mm)
Ø 6-5/8”
venting
23”
(584 mm)
7-1/2”
(191 mm)
25-1/8” (638 mm)
Centre of vent
B
x
Gas inlet position
3/8” fem. NPT
27-1/2” (699 mm)
14”
(356 mm)
17-7/8”
(454 mm)
32-1/2” minimum
Min. 2” between
combustible wall and
stove
42” minimum
Min. 2”
between
combustible
wall and
stove
um
xim
a
”m
26
Corner clearances
Alcove clearances
19
QUALIFIED
INSTALLER
Dimensions & Clearances
Contemporary Cast Stove MFCS04
1” (26 mm)
minimum
Suggested gas line
access point through wall.
Route to avoid optional fan.
3-7/8”
(98 mm)
10” (254 mm)
16-3/4 ” (425 mm)
Ø 6-5/8”
venting
Pipe supplied
with engine
(see engine
manual p. 18)
x
Mantel / shelf clearances
Gas line connection point
3/8” NPT FEMALE at valve
Mantel
0–1”
2–5”
6–18”
19–24”
Depth ‘A’ (0–26 mm) (51–127 mm) (152–457 mm) (483–610 mm)
Mantel
34”
36”
38”
42”
Height ‘B’ (864 mm)
(914 mm)
(965 mm)
(1067 mm)
2”
(52 mm)
minimum
A
Sidewall
Mantel
28-7/8 ” (733 mm)
Ø 6-5/8”
venting
26-3/4” (680 mm)
32-1/16 ” (814 mm)
Centre of vent
B
x
Hinged
control
access
door
x
Gas line
connection
point
28-1/4” (718 mm)
47
m
m
)
um
im 8” )
in 5/ m
M 12- m
21
(3
33” (839 mm) minimum
M
in
im
42” (1067 mm)
minimum
um
41
Zero clearance
Front surface
of base
26” (660 mm)
maximum
Minimum 58-1/4” (1480 mm)
Alcove Clearances
20
Gas line access
point 10” (254 mm)
90°
-3
/1
6”
(
10
Minimum
17-13/16”
(453 mm)
15-3/16”
(386 mm)
17-1/8”
(435 mm)
QUALIFIED
INSTALLER
Venting
Top / Rear Outlet
Wall Thickness
This unit is shipped with a top outlet collar which is
field-convertible to rear outlet—see page 29 for details.
The appliance vent is suitable for penetrating a
combustible wall assembly up to 14 inches (36 cm)
in thickness. A non-combustible wall can be of any
thickness up to the maximum horizontal run of vent
pipe allowed for the particular installation.
Vent Material
This unit is approved for installation using 4 by 6-5/8
inches co-axial direct vent pipe and accessories—see
list of approved venting pipes and accessories on
pages 36–37.
This unit may also be converted to co-linear (two 3
inches) venting (rear vent only) for use in solid-fuel
burning fireplaces and chimneys using adapters and
accessories—see list of approved venting pipes and
accessories on pages 36–37. Instructions for co-linear
conversion are packaged with the co-linear adapter.
Do not mix components from different vent manufacturers, with the exception of Valor’s 551DVK Horizontal
Termination Kit which can be used in combination with
approved manufacturers’ venting pipes listed on pages
36–37. Follow the installation instructions supplied with
the individual venting components.
Framing Vent in Combustible
Walls & Ceilings
When penetrating through combustible walls and
ceilings, frame a minimum of 10 by 10 inches opening
to ensure that the insulation is kept clear of the vent
pipe. Also, seal all joints between the wall plates,
the wall and the vent pipe. Follow the installation
instructions supplied with the individual venting
components.
10” (254 mm)
Align the vent
center to the
center of the
frame
Vent Sealing
Seal all outer coaxial pipe and elbow joints, including
sectioned elbow joints, using high quality, high temperature 2 inch wide self-adhesive aluminum foil tape
(Nashua-322-2 brand or similar). Wrap the tape completely around all joints and press firmly to seal.
A high temperature black silicone sealant may be used
in the outer joints as a substitute to foil tape.
Ensure all the pipe joints have a minimum of 1 ¼ inch
overlap.
10” (254 mm)
All horizontal pipe runs must be graded 1/4 inch per
foot upwards in the direction of the exhaust flow. The
final pipe length, when terminating through the wall
may be graded downwards slightly to prevent water
migration.
Important Installer Notice – Weather Sealing &
Vapor Barriers
Tape all joints
(including all
elbow joints)
It is the installer’s responsibility to ensure that vent installations through
exterior walls are caulked and weatherproofed in such a manner as to:
• Prevent rain water from entering the wall from the weather side
by adequately caulking the outer vent plate to the exterior wall
surface.
• Prevent moisture inside the home from penetrating into the wall
structure by ensuring the inside wall plate is adequately sealed to
the inside vapor barrier.
• Prevent rain water and moisture from entering the walls by sealing
the joints between the outer vent tube and the inner and outer wall
plates.
We recommend the use of a high quality polyurethane sealant.
21
QUALIFIED
INSTALLER
Venting
Typical Venting Components
See list of approved venting pipes and accessories on
pages 36–37.
Maximum pipe length:
24” (straight out with snorkel)
14” (45° elbow out with snorkel)
Snorkel required (min.
14” high) with horizontal
run through the wall
(no rise)
No more than one 45°
elbow allowed
Through wall (without vertical rise)
Through wall (with vertical rise)
22
Through roof
QUALIFIED
INSTALLER
Venting
4. A maximum of 5 x 90 degrees elbows or equivalent (2
x 45 degrees = 90 degrees) can be used.
5. Each 90 degrees elbow installed on the horizontal
plane is equivalent to a 3 feet horizontal pipe;
therefore, 3 feet must be subtracted from allowable
horizontal run.
(45 degrees elbow is equivalent to 18 inches horizontal
pipe.)
6. All horizontal pipe runs must be graded 1/4 inch per
foot upwards in the direction of the exhaust flow.
7. Co-linear rear venting in existing chimney systems is
limited to 40 feet vertical rise.
8. Restrictors are not required for co-linear
installations.
How to Read the Venting Chart
The chart below applies to top or rear outlet, roof or
wall termination with a vertical rise.
All rear outlet venting without a vertical rise must
be terminated by a snorkel.
1. The total length of the vent pipe cannot exceed 40
feet (12.2 m).
2. The minimum vertical height with roof termination is 8
feet (2.45 m).
3. Any combination of rise and run can be used as long
as they are within the allowable limits shown on the
chart below.
3” clearance
to combustible
above
horizontal pipe
Roof termination
V3
Wall termination
1” clearance
to combustible
around vertical
pipe
5 x 90º ELBOWS
MAXIMUM
40
1” clearance
to combustible
at bottom
and sides of
horizontal pipe
Allowable Vent
Configurations
38
36
34
NO
INSTALLATION
32
30
28
26
VERTICAL RISE
24
22
Restrictor 75
20
Example 1
18
16
14
12
10
Restrictor 50
8
6
Not to scale
Example 1
V Value = V1 (6’) + V2 (6’) + V3 (2’)= 14’
H Value = H1 (3’) + H2 (3’) = 6’
75% restrictor required
NO
RS
RICTO
T
RES
4
2
NO INSTALLATION
2
4
6
8
10
12
14
16
18
20
HORIZONTAL RUN
23
QUALIFIED
INSTALLER
Venting
Restrictors
SOME INSTALLATIONS REQUIRE RESTRICTORS.
For improved flame picture and performance, this unit
is supplied with two different sets of vent restrictors.
The level of restriction required depends on the vertical
rise in the venting system and, to a lesser degree, the
horizontal run and number of elbows.
The amount of restriction is based on laboratory tests.
The ideal restrictor position may vary slightly, especially
when the vent pipe length is near the limits of the
acceptable configurations for each type of restrictors.
The chart on the previous page shows the vent
restrictor required relative to the length of the vent pipe.
Restrictors are not required for co-linear applications.
To install restrictors:
1. Remove every second screw from the exhaust ports
in the top of the firebox.
2. Install the restrictors with the removed screws.
INSTALL RESTRICTORS HERE
50
75
OR
Restrictor 50
24
Restrictor 75
QUALIFIED
INSTALLER
Venting
Horizontal Vent Termination
• The vent terminal must be located on an outside wall or
through the roof.
• This direct vent appliance is designed to operate when
an undisturbed airflow hits the outside vent terminal
from any direction.
• The minimum clearances from this terminal that must be
maintained when located on an outside wall are shown
in the figure below.
Any reduction in these clearances could result in a
disruption of the airflow or a safety hazard. Local codes
or regulations may require greater clearances.
• The vent terminal must not be recessed into a wall or
siding.
• The vent terminal should be positioned where it will not
be covered by snowdrifts.
• Sidewall vent termination including 551DVK requires
a terminal guard such as 845TG when accessible—
within 7’ of ground.
Min. 72”
V
Max. 72”
G
A
Alcove detail
(open on one
side) Normal
ceiling/soffit
clearances
apply.
KEY
VENT TERMINAL LOCATIONS - MINIMUM DISTANCES
MINIMUM
CLEARANCE
Inches
Cm
A
Clearance above grade, verandah, porch, deck or balcony
12
30
B
Clearance to window or door that may be opened
12
30
C
Clearance to permanently closed window (recommended to prevent condensation on window)
12
30
D
Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet
(60 cm) from the center-line of the terminal
18
46
E
Clearance to unventilated soffit
12
30
F
Clearance to outside corner
12
30
G
Clearance to inside corner
12
30
H
Horizontal clearance to center-line of meter/regulator assembly located within 15 feet (4.6 m) below
the terminal
36
90
I
Clearance to service regulator vent outlet
36
90
J
Clearance to non-mechanical air supply inlet to the building or the combustion air inlet to any other
appliance
12
30
K
Clearance to a mechanical air supply inlet
72
180
L
Clearance above paved sidewalk or a paved driveway located on public property
Note: A vent must not terminate directly above a sidewalk or paved driveway, which is located
between two single-family dwellings and serves both dwellings
84
210
12
30
M
Clearance under a verandah, porch, deck or balcony
Only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the
floor
Note: Local codes and regulations may require different clearances.
25
QUALIFIED
INSTALLER
Vertical Vent Termination
Venting
Roof
Pitch
Flat to 7/12
Minimum
"H" (feet)
1'
Over 7/12 to
8/12
1.5'
Over 8/12 to
9/12
2’
Over 9/12 to
10/12
2.5’
Over 10/12 to
11/12
3.25’
Over 11/12 to
12/12
4’
Over 12/12 to
14/12
5’
Installation Planning
Only qualified licensed or trained personnel
should install this appliance.
Fan (Blower)
Allow for and install electrical wiring if there will be a fan
(blower) to install. Ask the homeowner if you are not
sure.
into consideration stove and vent clearances, allowable
vent terminal locations BEFORE cutting a hole in the
roof or wall. Avoid penetrating the wall/roof at structural
members.
Gas Line Routing
Consider visibility of shut-off valve or step-down
regulators, etc. when planning gas line routing.
Venting Configuration
This unit is supplied with a top outlet and is field
convertible to a rear outlet. Plan routing of vent taking
Appliance Preparation
Unpack the appliance and stove casing
The Madrona engine is supplied separately from the
stove casings. The Traditional stove—MFCS01 (black)
or MFCS02 (majolica brown)—and the Contemporary
stove MFCS04 are each supplied in two cartons. You
must have in hand the stove casing before starting the
assembly of the appliance.
Unpack the carton carefully. We strongly recommend
that you leave the engine sitting on the packaging
base in which it came to avoid damaging the
control valve, wires and pipes already attached
to the engine until it is ready to insert in the stove
casing.
26
Some parts are packed in the cardboard sleeve around
the engine; make sure you take them all out of the
packaging. Make sure you have all the components
including the stove casing components before you start
the installation.
CAUTION
LEAVE THE ENGINE ON ITS PACKAGING
BASE to avoid damage to the control valve,
wires and pipes until ready to insert into
stove casing.
Appliance Preparation
QUALIFIED
INSTALLER
Window & Log Pack
Gas Pipe & Connector
It is easier the remove the window and all the items
packed inside of the firebox to make the engine lighter
for installation.
1. Release the spring bolts at top and bottom of the
window by pushing and turning 1/4 turn.
Fit the pipe and connector supplied with the engine to
the valve. Connect the gas line to the inlet pipe.
3/8” gas line
connection
5/16” flare
Receiver Position
x4
2. Lift the window and set it aside in a safe place to
avoid damage.
3. Remove the log pack from inside the firebox and
set it aside with the window. Please handle the logs
carefully as they are made of fragile material and
can easily be damaged.
Once the gas pipe is fitted, clip the receiver on top of
the casting crossbar on the base, to the left hand side
of the valve. Make sure the receiver box is oriented
with its wires towards the back and its Reset button at
the front.
Casing Installation
1. Rough-in the gas line and electrical wiring for a fan
(if any).
2. Decide where the stove should be positioned to
avoid moving it once all the casing is put together.
3. Unpack the casing and follow the instructions
supplied with each model (MFCS01, MFCS02 or
MFCS04).
Receiver & clip
Lighting Instructions Plate
The lighting instructions plate is attached to the back of
the engine and may have slid out of its slot. Reposition
the plate if this is the case.
Remote Control Receiver
Receiver clipped to crossbar in final position
Under the engine,
the receiver box is
clipped to the burner
pipes to facilitate
transportation.
Unclip the box and
let it hang while you
fit the gas pipe.
Receiver hooked to burner pipes
27
QUALIFIED
INSTALLER
Appliance Preparation
Optional Fan (Blower)
If the Circulating Fan Kit (blower) is to be installed, we
suggest that you do it now.
1. Take the fan out of its package.
2. Remove the mounting plate from the fan and
discard it.
3. Position the fan in such a way that its exhaust is
directed upwards, towards the space between the
inner and the outer walls of the firebox.
NOTE: You may need to remove the burner to
access the back of the stove. If this is the case, first
remove the rear log support (NG/LPG) and the front
log support (LPG), and then, the burner.
4. Using 3 screws, fix the fan to the firebox bracket.
5. Fix the fan control box bracket provided to the
control box with 2 screws.
6. Fix the bracket, with the control box attached, to the
casting base of the stove from underneath.
Fan control
box position
Fan control
box position
Fan control
box bracket
Stove MFCS01 or MFCS02
28
Fan control
box bracket
Stove MFCS04
7. With 2 screws from the burner plate, fix the fan’s
thermoswitch to the underside of the burner plate,
behind the pilot area.
Fasten thermal switch to
underside of burner module
using 2 existing screws
8. See instructions with the 555CFK kit for complete
details.
Appliance Preparation
QUALIFIED
INSTALLER
Venting Outlet
If the appliance is to be vented from the top, it is ready
for vent installation once the engine is on the casting
base.
If the appliance is to be vented from the rear, it must be
converted. Follow these simple steps:
1. Remove the following parts in this order:
a) Dura-Vent collar, gasket and intake plate from
the top of the appliance (22 screws of the intake
plate and 2 rear screws of the collar);
b) Exhaust collar (8 screws).
NOTE: The gaskets are glued to the engine or
the intake plate; it is not necessary to separate
them from the parts they are attached to.
However, if they need to be manipulated, BE
CAREFUL not to damage them because their
material is fragile.
2. Re-install through the vent opening at the rear of the
firebox in the reverse order in which you took the
parts out.
Co-linear Applications (Rear Outlet ONLY)
For conversion of rear outlet collar to co-linear
(two 3-inch pipes) rear venting, refer to instructions
packaged with the 556CLA Co-linear Adapter.
NOTE: Co-linear venting may only be installed into
solid-fuel burning fireplaces and chimneys.
29
QUALIFIED
INSTALLER
Supply Gas Installation
• The gas supply inlet connection is a 3/8 inch
NPT female connector. For detailed location of
this connector see the drawing on page 18. If a
circulating fan or isolating valve is to be installed,
adjust the routing of the gas line to suit.
• Use only new black iron or steel pipes or copper
tubing if acceptable—check local codes. Note that
in USA, copper tubing must be internally tinned for
protection against sulfur compounds.
• Unions in gas lines should be of ground joint type.
• The gas supply line must be sized and installed
to provide a supply of gas sufficient to meet the
maximum demand of the appliance without undue
loss of pressure.
• Sealant used must be resistant to the action of all
gas constituents including LP gas. Sealant should
be applied lightly to male threads to ensure excess
sealant does not enter gas lines.
• The supply line should include a manual shutoff valve and union to allow the appliance to be
disconnected for servicing.
• Pressure test the supply line for leaks.
• The appliance and its individual shut-off valve
must be disconnected from the gas supply
piping system during any pressure testing of
that system at test pressures in excess of 1/2
psig (3.5 kPa).
• The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure testing
of the gas supply piping system at test pressures
equal to or less than 1/2 psig (3.5 kPa).
• Failure to either disconnect or isolate the appliance
during pressure testing may result in regulator or
valve damages and void the warranty. Consult your
dealer in case of damages.
• The minimum supply pressure is given in the
Specifications section of this manual—page 18.
• All piping and connections must be tested for leaks
after installation or servicing. All leaks must be
corrected immediately.
30
• When testing for leaks:
• Make sure that the appliance is turned off.
• Open the manual shut-off valve.
• Test for leaks by applying a liquid detergent
or soap solution to all joints. Bubbles forming
indicate a gas leak.
Never use an open flame to check for leaks.
Correct any leak detected immediately.
• The pressure test tapping locations are shown
in the figure below. A built-in non-adjustable
regulator controls the burner manifold pressure.
The correct pressure range is shown in the table
in Specifications section of this manual on page
18. The pressure check should be made with the
burner alight and at its highest setting. See Lighting
Instructions section on page 15 for full operating
details.
QUALIFIED
INSTALLER
Ceramic Logs Installation
Unpack the ceramic logs very carefully to avoid damaging their fragile material. Install the logs as shown below.
Please note that the position of the logs is critical to insure the good performance of the appliance.
1. Place the rear log on the sheet metal support. Pull
it forward until the notch in the underside of the
log sits against the front edge of the sheet metal
support. Slide the log towards the left hand side until
the notch in the log touches the right angled return
edge of the pilot shield as indicated.
3. Place the top left log on the pin of the rear log. The
bottom of the log rests on the left side end of the
front left log just installed.
Note: Make sure the lower end of the top log rests
on the front log as indicated and does not fall below
in the firebox.
Rear log pushed to
the left abuts the
pilot shield
2. Place the front left log on the burner. Slide it towards
the left until its narrow end rests in the notch of the
rear log as indicated.
Pilot area
This log must
rest ON the
front log
Front log
31
QUALIFIED
INSTALLER
Ceramic Logs Installation
4. Place the front right log on the burner and slide it to
the left against the front left log.
6. Place the lower end of the center right log onto the
pin on the front right log. Rest the narrow end in the
notch into the rear log.
Notch in rear log
5. Locate the top right log on the two pins on the right
side of the rear log. Ensure a tight fit against the flat
area around the pins in the rear log.
Pin in front
right log
Window Refitting
To refit the window:
1. Place it on the firebox frame and hold it in place
while pushing and turning its fastening studs 90
degrees.
IMPORTANT: To ensure a safe operation, verify
that the bolts are hooked properly to the window
tabs; then, pull out the top of the window and
release it to insure the springs return it.
2. Then, apply light hand pressure against the window
frame sides to bed-in the window seal.
3. If the Hot Glass Warning plate has been
removed from the front lower corner of the
window, reinstall it by sliding it between the
glass and the frame as indicated.
32
x4
Hot Glass Warning Plate
QUALIFIED
INSTALLER
Remote Control Initial Set-up
The receiver and the handset of the remote control
system must be initially synchronized before the first
use.
1. Insert alkaline batteries in the remote control
receiver and handset. The receiver is located left of
the control valve under the burner module.
2. With a sharp object, press and hold the receiver’s
reset button until you hear one short and one long
beeps. After the second beep, release the reset
button.
3. Within the subsequent 20 seconds, press the small
flame button (
) on the remote handset until you
hear two short beeps confirming the sychronization
is set.
This is a one time setting only and is not required when
changing the batteries in the remote receiver. The
remote control system is now ready to use.
Operation Check & Aeration Settings Adjustment
Operation Check
Turn the fireplace flame up and down using the
remote control to confirm that the full range of inputs
is achieved—see the remote control operation
instructions on pages 10–14.
Aeration Settings
Light the fire and allow the unit to warm up for 10–15
minutes to evaluate the flame picture. The burner
is equipped with an adjustable shutter to control
primary aeration. See the figures below. The shutter is
factory-set to an aeration gap which will give optimum
performance for the vast majority of installations.
In a few unusual installations, the flame picture may
be improved by adjusting the aeration. The need for
adjustment should be determined only by operating the
appliance with the ceramic logs and window installed.
Increasing aeration will cause the flames to appear
more transparent and blue making the ceramic logs
glow more.
Decreasing aeration will cause the flames to appear
more yellow or orange making the ceramic logs glow less.
Too little aeration may result in black carbon
forming and dropping into the firebox.
Air Shutter
NG
LPG
Close
Flashback
shield (for
LPG only)
Open
NG Air Shutter
Slider & Cover
Close
Open
LPG Air Shutter
Slider
Close
Open
33
QUALIFIED
INSTALLER
Front and Barrier Screen Installation
When installing the front of the stove make sure you
install as well the barrier screen provided with the cast
stove body.
Show the customer how to remove the barrier screen
and how to access the controls.
Follow the instructions provided with the stove cast
body and leave those instructions behind for the
customer’s further reference.
Remote Control Handset Wall Holder Installation
The remote ontrol kit for this fireplace comes
Alternative 2
Alternative 3
Packing Contents:
complete with a wall-mounted holder. This
holder is not required in all installations but
1 Wall Bracket A
is provided as an optional feature for those
2 Screws B
1 Screw C
customers who wish to mount the remote
2 Wall Anchor D
handset to the wall. To install the holder
1 Spacer E
(detach before assembly)
to the wall, find a convenient location and
Switch Plate
use the hardware provided with the kit.
See the diagram for required hardware and
1 Wall Bracket F
configurations. Note that the holder can be
Alternative 1
installed at the base of a light switch plate.
IMPORTANT: The location of the remote
control handset is important to assure
proper temperature regulation. To obtain a
constant temperature, we recommend that
the handset should be between 3 and 15 feet away from the appliance but not directly above it. We also advise
that the handset should be located away from any other heat source and not in direct sunlight as this may affect the
temperature sensor located in the remote handset.
34
QUALIFIED
INSTALLER
Wiring Diagram
Optional Wall
Switch Kit
1265WSK
Connector
Yellow
Red
GV60 Wiring Diagram
35
QUALIFIED
INSTALLER
Approved Venting Components
Approved Direct Vent Suppliers for Valor Models 530, 534, 535, 650, and MF28
—
Vertical
Termination Caps
Vent Adapters / Couplers
Aluminum
Flexible
Liner
Adjustable Pipe Length
4” x 6-5/8”
DV 45°
Elbows
—
—
—
—
551DVK
4DT-HC
TM-4HT
—
—
4DHC round
—
—
TM-4DHT
—
—
4DHCS square
—
—
—
SV4CHC
—
—
—
46DVA-VC
4DT-VC
TM-4VT
—
HSDV4658-1313
High Wind Co-axial
46DVA-VCH
—
—
SV4CGV
—
Extended Co-axial
46DVA-VCE
—
—
—
—
—
—
4DVC
4DH-1313
—
—
—
—
—
—
HS-C33U-99
HCL-99-33
HS-C33F-1313
HCL-1313-33
3PDVCV
HCL-913-33
559CLT
Snorkel, 14” Rise
46DVA-SNK14
4DT-ST14
TM-4ST14
—
—
4D14S
—
Snorkel, 36” Rise
46DVA-SNK36
4DT-ST36
TM-4ST36
—
—
4D36S
—
Universal Adapter 3”
Flex Coupler
2150
—
TM-CFAA3
—
—
—
—
Valor Adapter
817VAK
—
—
—
—
4DSC-V
—
Co-linear Flex Connector
46DVA-ADF
—
—
—
—
—
—
Co-axial-to-Co-linear
Adapter
46DVA-GCL
—
TM-4CAA
—
—
4DCAB33
556CLA
Co-linear-to-Co-axial
Adapter
46DVA-GK
—
TM-4CTA
—
—
4DCAT33
—
3” diameter
NOTE: 2-ply liner approved to CAN/ULC S635 suitable for venting gas appliances. As manufactured
by Z-Flex, Flexmaster or others.
2280 Series
4” to 10”
1-1/2” to 6”
1-1/2” to 12”
Galvanized
Black
Galvanized
Black
Galvanized
—
3” ACFL
4DT-ADJ
4DT-ADJ(B)
—
—
—
—
Black
1-1/2” to 24”
Galvanized
Black
—
—
—
—
—
—
—
—
4D7A or 4D7AB
(3” to 5”)
—
—
4D12A or 4D12AB
(3” to 10”)
—
—
4D16A or 4D16AB
(3” to 14”)
—
—
4D26A or 4D26AB
(3” to 24”)
—
—
SV4LA
SV4LBA
TC-4DLT
SV4LA12
TC-4DLTB
SV4LBA12
—
SV4LA24
SV4LBA24
Galvanized
46DVA-E45
—
TE-4DE45
—
Black
46DVA-E45B
—
TE-4DE45B
SV4EBR45
Galvanized Swivel
Black Swivel
DV 90°
Elbows
—
Standard Co-axial
Co-linear
36
MILES
INDUSTRIES
High Wind Co-axial
AMERIVENT
—
RLH
INDUSTRIES
46DVA-HC
Deluxe Co-axial
SECURE
VENT
Standard Co-axial
ICC EXCEL
DIRECT
—
SELKIRK
Co-axial Kit, 26” long
Horizontal
Venting Parts Description
DURA-VENT
Venting Parts Code / availability by Manufacturer
—
4DT-EL45
4DT-EL45(B)
—
SV4E45
SV4EB45
Galvanized
46DVA-E90
—
TE-4DE90
—
Black
46DAV-E90B
—
TE-4DE90B
SV4EBR90
Galvanized Swivel
—
4DT-EL90
Black Swivel
—
4DT-EL90(B)
—
SV4E90
SV4EB90
—
—
—
—
3AFL-35
—
4D45L
—
4D45LB
—
—
—
4D90L
—
4D90LB
—
—
—
QUALIFIED
INSTALLER
Approved Venting Components
24” long
36” long
46DVA-06
4DT-06
TC-4DL6
SV4L6
Black
46DVA-06B
4DT-06(B)
TC-4DL6B
SV4LB6
—
—
—
—
—
Galvanized
46DVA-09
4DT-09
Black
46DVA-09B
4DT-09(B)
—
—
—
Galvanized
46DVA-12
4DT-12
TC-4DL1
SV4L12
Black
46DVA-12B
4DT-12(B)
TC-4DL1B
SV4LB12
Galvanized
46DVA-18
4DT-18
Black
46DVA-18B
4DT-18(B)
—
—
Galvanized
46DVA-24
4DT-24
TC-4DL2
SV4L24
Black
46DVA-24B
4DT-24(B)
TC-4DL2B
SV4LB24
Flashings
Various Venting System Parts
Galvanized
Black
Galvanized
46DVA-36
4DT-36
Black
46DVA-36B
4DT-36(B)
—
SV4L36
SV4LB36
—
—
—
—
4D7
4D7B
—
4D12
4D12B
—
4D2
4D2B
4D3
4D3B
—
—
—
—
—
46DVA-48
4DT-48
TC-4DL4
SV4L48
Black
46DVA-48B
4DT-48(B)
TC-4DL4B
SV4LB48
Roof Flashing
0/12-6/12
46DVA-F6
4DT-AF6
TF-4FA
SV4FA
—
4DF
(0/12-5/12)
—
Roof Flashing
7/12-12/12
46DVA-F12
4DT-AF12
TF-4FB
SV4B
—
4DF12
(6/12-12/12)
—
Flat Roof Flashing
46DVA-FF
—
TF-4F
SV4F
—
—
559FSK
Masonry Flashing
—
—
TF-4MF
—
—
—
—
Wall Thimble
46DVA-WT
4DT-WT
TM-4WT
SV4RSM
—
4DWT
—
—
4D4
—
Galvanized
48” long
Notes:
MILES
INDUSTRIES
SECURE
VENT
18” long
AMERIVENT
ICC EXCEL
DIRECT
12” long
—
SELKIRK
9” long
—
DURA-VENT
Pipes 4” x 6 5/8” ( ID x OD )
7” long
—
Galvanized
Venting Parts Description
6” long
RLH
INDUSTRIES
Venting Parts Code / availability by Manufacturer
4D4B
—
Storm Collar
46DVA-SC
4DT-SC
TM-SC
SV4AC
—
4DSC
—
Decorative Plate
46DVA-DC
4DT-CS
TM-4TR
SV4PF
—
4DFPB
—
Cathedral Ceiling
Support
46DVA-CS
4DT-CCS
—
—
—
4DRSB
—
Ceiling Firestop /
Floor Support
46DVA-FS
4DT-FS
TM-CS
—
4DFSP
—
Attic Radiation Shield /
Firestop
—
—
TM-4AS
SV4BF
SV4SD
—
—
4DAIS12 (12”)
4DAIS36 (36”)
—
Wall Strap
46DVA-WS
4DTWS
TM-WS
—
—
4DWS
—
Vinyl Siding Standoff
46DVA-VSS
4DT-VS
TM-VSS
SV4VS
—
4DHVS
—
Elbow Strap / Offset
Support
46DVA-ES
4DT-OS
TM-OS
—
—
—
—
Terminal Guard
46DVA-WG
—
—
—
—
—
845TG
1) All listed above co-axial pipes and fittings require Valor 817VAK Adapter Kit to fit Valor’s smooth collars (Valor adapter 4DSC-V by
American Metal Products may also be used).
2) Follow instructions supplied with each manufacturer’s components.
3) Unless otherwise specified, all the parts and assemblies from the above table are to be used with 4” x 6-5/8” pipes.
4) Do not mix components from different vent manufacturers.
5) Termination caps manufactured by RLH Industries or American Metal Products are from Homestyle Chimney Collection and can be
ordered in one of the following finishes: a) aluminium; b) black powder coated; c) solid copper.
37
OWNER’S
INFORMATION
WA
TY
N
A
RR
M
GR A
O
PR
T
LOR
OR
If you have a problem with this unit, please contact your dealer or
supplier immediately. Under no circumstances should you attempt
to service the unit in any way by yourself. The warranties in
paragraphs 1 and 2 are provided only to the first purchaser/user of
this unit, are not transferable and are subject to the conditions and
limitations in paragraphs 3, 4 and 5. Please review the conditions
and limitations carefully and strictly follow their requirements.
VA
Warranty
CO M F
1. Extended Warranty Coverage
For a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at its option pay the
initial purchaser for the repair of, or will exchange the following parts or components which are found to be defective in material or
workmanship under normal conditions of use and service:
Part or Component
Defect Covered
Maximum Warranty Period
Exterior steel casing
Corrosion
10 years
Glass
Loss of structural integrity
10 years
Cast iron parts
Corrosion
10 years
Firebox and heat exchanger
Corrosion (but not discoloration) causing
loss of structural integrity
10 years
2. Two-Year Parts Warranty
In addition, for two (2) years from the date of purchase, the Company, at its option, can repair or exchange all parts and components
not listed above but that are found to have a bona fide defect in material or workmanship under normal conditions of use.
3. Conditions and Limitations
a) The warranty registration card must be completed by the initial owner and returned to the Company within 90 days of purchase.
b) Installation and maintenance must be performed by an authorized and trained dealer in accordance with the Company’s installation
instructions.
c) This warranty is void where installation of the unit does not conform to all applicable codes including national and local gas
appliance installation codes and building and fire codes.
d) The owner must comply with all operating instructions.
e) The Company is not responsible for the labor costs to remove defective parts or re-install repaired or replacement parts.
f) The first purchaser or user of the unit will be responsible for any shipping charges for replacement parts as well as travel time
incurred by the dealer to perform the warranty work.
g) This warranty applies to non-commercial use and service and is void if it is apparent that there is abuse, misuse, alteration,
improper installation, accident or lack of maintenance to the unit.
h) This warranty does not cover damage to the unit through:
i)
Improper installation, operational or environmental conditions.
ii)
Inadequate ventilation in the area or competition for air from other household equipment or appliances.
iii)
Damage due to chemicals, dampness, condensation, or sulphur in the fuel supply lines which exceeds industry standards.
i)
This warranty does not cover glass, log breakage or damage to the unit while in transit.
j)
The Company does not allow anyone to extend, alter or modify this warranty and assumes no responsibility for direct, indirect or
consequential damages caused by the unit. State or provincial laws where the first purchaser or user resides may provide specific
rights to extend this warranty and, if so, the Company’s sole obligation under this warranty is to provide labor and/or materials in
accordance with those laws.
4. Discharge of Liability
After two (2) years from the date of purchase, the Company may, at its option, fully discharge all obligations under this warranty by
paying to the first purchaser/user the wholesale price of any defective parts.
5. No Other Warranty
All obligations to repair this unit are defined in this warranty. Some states or provinces may specifically mandate additional warranties on
the part of manufacturers, but in the absence of such specific legislation, there is no other warranty or obligation expressed or implied.
38
OWNER’S
INFORMATION
Spare Parts
Engine Parts
Description
Part no.
Description
Part no.
1
Log Set Complete
4003804
32
Hooked Olive for Pilot
Injector
720A196
2
Rear Log
4003803
33
Olive Nut—Pilot Pipe to Pilot
Assembly
420K385
3
Left Top Log
4003796
34
Electrode
720A543
4
Right Top Log
4003797
35
Electrode Retaining Nut
720A200
5
Right Center Log
4003798
36
Thermocouple
4000061
6
Left Front Log
4003800
37
Pilot Shield
4000144
7
Right Front Log
4003801
38
Pilot Gasket
4000139
8
Restrictor 50 (2)
4000949
39
Pilot Mount
4000138
9
Restrictor 75 (2)
4000950
40
Pilot Mount Gasket
4000140
4000065
10
Dura-Vent Intake Collar
4000925
41
Pipe—Valve to Main Burner
(incl. olive & nuts)
11
Intake Collar Gasket
4000942
42
Valve Tray
4001627
12
Exhaust Collar Assembly
4000909
43
Rear Gasket
4000642
13
Exhaust Collar Gasket
4000938
44
RH Side Gasket
4000643
14
Intake Plate
4000908
45
Front Gasket
4000641
15
Intake Plate Gasket
4000941
46
LH Side Gasket
4000644
220K913
16
R/H Stove Back Corner
4000922
47
Break-off Olive Nut—Pilot
Pipe to Valve
17
L/H Stove Back Corner
4000923
48
Pipe—Valve to Pilot
4000066
18
Firebox Assembly
4000920AH
49
Inlet Connector
220K997
19
Rear Log Support
4001890
50
Inlet Pipe
030A224
20
Window Assembly
4000919
52
Valve Mounting Bracket
4000141
21
Heat Reduction Baffle
4000974
53
Switch Bracket
4001070
22
Top Spar
4000916
54
Thermocurrent Interruptor
4001037
23
24
Burner Tray Assy NG
4001892S
56a GV60 Complete Valve NG
4003102
Burner Tray Assy LPG
4001893S
56b GV60 Complete Valve LPG
4003115
Burner NG
740K189
57
4001910
Handset G6R H3T5-ZV (BJ)
Burner LPG
740K190
58
Receiver G6R-R3AM-ZV (CP)
4001911
25a
Air Shutter Cover (NG)
4002346
59
Wiring Harness
4001187
25b
Flashback Shield (LPG)
3000371
60
Handset Wall Holder
9000008
26a
Air Shutter Slider (NG)
4002345
62
Ignition Cable
4001039
26b
Air Shutter Slider (LPG)
320B293
62a Ignition Cable Sleeve
4002244
27
28
29
30
31
Injector Elbow NG 82-750
4000738
63
Cable Interruptor/Receiver
4001035
Injector Elbow LP 92-300
9730035
64
Switch with Cable
4001036
Burner Mounts (2)
4000132
65
Receiver Clip
4001164
Pilot Assembly NG
4000062S
66
Fan Control Bracket
9000946
Pilot Assembly LPG
4000063S
not
shown
Pilot Tube Connector
4001034
Pilot Bracket
720A542
67
Hot Glass Warning Plate
4003093
Pilot Injector NG—No 35
4002511
Pilot Injector LPG—No 27
720A195
39
OWNER’S
INFORMATION
Spare Parts
2
50
1
10
11
12
8
4
3
75
5
6
13
7
14
9
17
22
15
16
18
21
20
19
24
NG
25a
25b
LPG
23
31
32
33
34
35
67
26b
27
28
29
30
37
38
39
40
36
65
66
26a
41
48
42
47
46
62a
62
63
64
43
49
45
44
52
50
53
58
56a, 56b
60
40
59
57
54
Thank You ...
For purchasing a Valor by Miles Industries. Your new radiant gas
heater is a technical appliance that must be installed by a qualified
installer.
Please fill in the information below. The information provided
will be used for customer records only.
Fireplace Information
Model Number: MF28
JLN or
JLP
Serial Number:
Date Purchase (yyyy-mm-dd):
Dealer:
Customer Information
First Name:
Last Name:
Contact Information
Email:
Mailing Address
Address:
City:
Province/State:
Postal/Zip Code:
Country:
Cut out page, fill information, and mail to Miles Industries Ltd.
Online Warranty registration at www.valorfireplaces.com
Tape Shut
Fold here
Postage
needed
Miles Industries Ltd.
190 - 2255 Dollarton Highway
North Vancouver, BC V7H 3B1
Canada
Online Warranty registration at www.valorfireplaces.com
Thank you for choosing a Valor Product
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement