BeneVision Central Station Operators Manual

BeneVision Central Station Operators Manual
BeneVision
Central Monitoring System
Operator’s Manual
© Copyright 2013-2015 Shenzhen Mindray Bio-Medical Electronics Co., Ltd. All rights
reserved.
For this Operator‟s Manual, the issue date is 2015-06.
WARNING

Federal Law (USA) restricts this device to sale by or on the order of a physician.
BeneVision CMS Operator‟s Manual
I
Intellectual Property Statement
SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS CO., LTD. (hereinafter called
Mindray) owns the intellectual property rights to this Mindray product and this manual.
This manual may refer to information protected by copyright or patents and does not convey
any license under the patent rights or copyright of Mindray, or of others.
Mindray intends to maintain the contents of this manual as confidential information.
Disclosure of the information in this manual in any manner whatsoever without the written
permission of Mindray is strictly forbidden.
Release, amendment, reproduction, distribution, rental, adaptation, translation or any other
derivative work of this manual in any manner whatsoever without the written permission of
Mindray is strictly forbidden.
,
and
are the trademarks, registered or otherwise, of
Mindray in China and other countries. All other trademarks that appear in this manual are
used only for informational or editorial purposes. They are the property of their respective
owners.
II
BeneVision CMS Operator‟s Manual
Manufacturer’s Responsibility
Contents of this manual are subject to change without prior notice.
All information contained in this manual is believed to be correct. Mindray shall not be
liable for errors contained herein or for incidental or consequential damages in connection
with the furnishing, performance, or use of this manual.
Mindray is responsible for the effects on safety, reliability and performance of this product,
only if:
 all installation operations, expansions, changes, modifications and repairs of this product
are conducted by Mindray authorized personnel;
 the electrical installation of the relevant room complies with the applicable national and
local requirements; and
 the product is used in accordance with the instructions for use.
NOTE

This equipment must be operated by skilled/trained clinical professionals.
WARNING

It is important for the hospital or organization that uses this equipment to perform a
reasonable service/maintenance plan. Neglecting this may result in machine
breakdown or personal injury.
BeneVision CMS Operator‟s Manual
III
Warranty
Mindray warrants that components within its products will be free from defects in
workmanship and materials for a period of three years from the date of purchase except that
disposable or one-time use products are warranted to be free from defects in workmanship
and materials up to a date one year from the date of purchase or the date of first use,
whichever is sooner.
This warranty does not cover consumable items such as, but not limited to, batteries,
external cables, and sensors.
Mindray shall not be liable for any incidental, special, or consequential loss, damage, or
expense directly or indirectly arising from the use of its products. Liability under this
warranty and the buyer‟s exclusive remedy under this warranty is limited to servicing or
replacing the affected products, at Mindray‟s option, at the factory or at an authorized
distributor, for any product which shall under normal use and service appear to Mindray to
have been defective in material or workmanship. Recommended preventative maintenance,
as prescribed in the service manual, is the responsibility of the user and is not covered by
this warranty.
No agent, employee, or representative of Mindray has any authority to bind Mindray to any
affirmation, representation, or warranty concerning its products, and any affirmation,
representation or warranty made by any agent, employee, or representative shall not be
enforceable by buyer or user.
THIS WARRANTY IS EXPRESSLY IN LIEU OF, AND MINDRAY EXPRESSLY
DISCLAIMS, ANY OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY, NON-INFRINGEMENT, OR
FITNESS FOR A PARTICULAR PURPOSE, AND OF ANY OTHER OBLIGATION ON
THE PART OF MINDRAY.
Damage to any product or parts through misuse, neglect, accident, or by affixing any nonstandard accessory attachments, or by any customer modification voids this warranty.
Mindray makes no warranty whatsoever in regard to trade accessories, such being subject to
the warranty of their respective manufacturers.
A condition of this warranty is that the equipment or accessories which are claimed to be
defective be returned when authorized, freight prepaid to Mindray DS USA, Inc., Mahwah,
New Jersey 07430 or its authorized representative. Mindray shall not have any
responsibility in the event of loss or damage in transit.
IV
BeneVision CMS Operator‟s Manual
Exemptions
Mindray's obligation or liability under this warranty does not include any transportation or
other charges or liability for direct, indirect or consequential damages or delay resulting
from the improper use or application of the product or the use of parts or accessories not
approved by Mindray or repairs by people other than Mindray authorized personnel.
This warranty shall not extend to:
 Malfunction or damage caused by improper use or man-made failure.
 Malfunction or damage caused by unstable or out-of-range power input.
 Malfunction or damage caused by force majeure event, such as (i) flood, fire and
earthquake , or other similar elements of nature or acts of God; (ii) riots, war, civil
disorders, rebellions, or revolutions in any country; or (iii) any other cause beyond the
reasonable control of Mindray.
 Malfunction or damage caused by improper operation or repair by unqualified or
unauthorized service people.
 Malfunction of the instrument or part whose serial number is not legible enough.
 Others not caused by instrument or part itself.
BeneVision CMS Operator‟s Manual
V
Company Contact
Manufacturer:
Address:
VI
Website:
E-mail Address:
Tel:
Fax:
Shenzhen Mindray Bio-Medical Electronics Co., Ltd.
Mindray Building,Keji 12th Road South, High-tech industrial
park,Nanshan,Shenzhen 518057, P.R.China
www.mindray.com
[email protected]
+86 755 81888998
+86 755 26582680
Distributor:
Mindray DS USA, Inc.
Address:
800 MacArthur Boulevard Mahwah, New Jersey 07430 USA
Tel:
1.800.288.2121, 1.201.995.8000
Website:
www.mindray.com
BeneVision CMS Operator‟s Manual
Preface
Manual Purpose
This manual contains the instructions necessary to operate the product safely and in
accordance with its function and intended use. Observance of this manual is a prerequisite
for proper product performance and correct operation and ensures patient and operator
safety.
This manual is based on the maximum configuration and therefore some contents may not
apply to your product. If you have any question, please contact Mindray.
This manual is an integral part of the product. It should always be kept close to the
equipment so that it can be obtained conveniently when needed.
Intended Audience
This manual is geared for clinical professionals who are expected to have a working
knowledge of medical procedures, practices and terminology as required for monitoring of
critically ill patients.
Illustrations
All illustrations in this manual serve as examples only. They may not necessarily reflect the
setup or data displayed on the equipment.
Conventions
 Italic text is used in this manual to quote the referenced chapters or sections.
 The terms danger, warning, and caution are used throughout this manual to point out
hazards and to designate a degree or level or seriousness.
BeneVision CMS Operator‟s Manual
VII
FOR YOUR NOTES
VIII
BeneVision CMS Operator‟s Manual
Contents
1 Safety ......................................................................................................................................... 1-1
1.1 Safety Information .......................................................................................................... 1-1
1.1.1 Warnings............................................................................................................... 1-2
1.1.2 Cautions ............................................................................................................... 1-3
1.1.3 Notes .................................................................................................................... 1-4
1.2 Equipment Symbols ........................................................................................................ 1-4
2 The Basics ................................................................................................................................. 2-1
2.1 Intended Use ................................................................................................................... 2-1
2.2 Contraindications ............................................................................................................ 2-2
2.3 CMS Functions & Features ............................................................................................. 2-2
2.4 Components .................................................................................................................... 2-5
2.5 Networking Mode ........................................................................................................... 2-6
2.6 Controls ........................................................................................................................... 2-7
2.6.1 Mouse ................................................................................................................... 2-7
2.6.2 Keyboard .............................................................................................................. 2-8
2.6.3 Touchscreen.......................................................................................................... 2-8
2.6.4 Controls ................................................................................................................ 2-8
3 Installation and Maintenance.................................................................................................. 3-1
3.1 Unpacking and Inspection ............................................................................................... 3-1
3.2 Installation ....................................................................................................................... 3-2
3.2.1 Environmental Requirements ............................................................................... 3-2
3.2.2 Power Requirements ............................................................................................ 3-3
3.3 Starting the System ......................................................................................................... 3-3
3.4 Shutting Down the System .............................................................................................. 3-4
3.5 Maintenance .................................................................................................................... 3-4
3.5.1 General Inspection ............................................................................................... 3-5
3.5.2 General Cleaning.................................................................................................. 3-6
4 Display....................................................................................................................................... 4-1
4.1 Overview ......................................................................................................................... 4-1
4.2 Single-Screen Mode ........................................................................................................ 4-1
4.2.1 Main Screen ......................................................................................................... 4-1
4.2.2 Auxiliary Screen ................................................................................................... 4-4
4.3 Multiple Screen Mode ..................................................................................................... 4-5
4.4 Assigning a Device on WorkStation and ViewStation .................................................... 4-6
5 Patient Management ................................................................................................................ 5-1
5.1 Monitoring a Patient........................................................................................................ 5-2
BeneVision CMS Operator‟s Manual
1
5.1.1 Using a Monitor ................................................................................................... 5-2
5.1.2 Using a Telemetry ................................................................................................ 5-3
5.1.3 Auto Waveform Storage ....................................................................................... 5-4
5.2 Obtaining Patient Information......................................................................................... 5-5
5.3 Synchronizing Patient Information ................................................................................. 5-6
5.4 Modifying Patient Information........................................................................................ 5-6
5.4.1 Inconsistent Patient Information between Monitor and CentralStation ............... 5-7
5.5 Discharging a Patient ...................................................................................................... 5-7
5.6 Switching Patient Windows ............................................................................................ 5-9
5.7 Changing to Idle Sector ................................................................................................... 5-9
5.8 Transferring a Patient ...................................................................................................... 5-9
5.8.1 Transferring a Patient on CentralStation .............................................................. 5-9
5.8.2 Transferring a Patient on Monitor .......................................................................5-11
5.9 Finding a Patient ............................................................................................................5-11
6 Multibed Screen ....................................................................................................................... 6-1
6.1 Overview ......................................................................................................................... 6-1
6.2 Screen Layout ................................................................................................................. 6-2
6.3 Patient Window ............................................................................................................... 6-2
6.3.1 Non-Spot Patient Window .................................................................................... 6-2
6.3.2 Spot Patient Windows .......................................................................................... 6-3
6.3.3 Patient Window in Monitoring Status .................................................................. 6-4
6.4 Display Setup .................................................................................................................. 6-9
6.4.1 Multibed Waveform Setup ................................................................................... 6-9
6.4.2 Multibed Numeric Setup .................................................................................... 6-10
7 ViewBed .................................................................................................................................... 7-1
7.1 Overview ......................................................................................................................... 7-1
7.2 ViewBed Screen .............................................................................................................. 7-2
7.2.1 Function Drop-down Menu .................................................................................. 7-3
7.2.2 View Drop-down Menu ........................................................................................ 7-4
7.2.3 Waveform Area..................................................................................................... 7-4
7.2.4 Parameter Area ..................................................................................................... 7-5
7.3 Parameter Setup .............................................................................................................. 7-5
7.4 Basic Operations ............................................................................................................. 7-6
7.4.1 Alarm Setup.......................................................................................................... 7-6
7.4.2 Resetting Alarms on Monitors.............................................................................. 7-6
7.4.3 Pausing Alarms..................................................................................................... 7-6
7.4.4 Controlling a Telemetry to Enter/Exit Standby .................................................... 7-6
7.4.5 Controlling a Bedside Monitor to Exit Standby ................................................... 7-7
7.4.6 NIBP Measurement .............................................................................................. 7-7
7.4.7 Freeze/Unfreeze Waveforms ................................................................................ 7-7
7.4.8 Parameter Order ................................................................................................... 7-8
7.4.9 Record .................................................................................................................. 7-8
2
BeneVision CMS Operator‟s Manual
7.4.10 Print .................................................................................................................... 7-9
7.4.11 Show/Hide Alarm Limits.................................................................................. 7-10
7.4.12 Show/Hide Dynamic Trends ............................................................................ 7-10
7.4.13 Show/Hide Multi-Lead ECG ............................................................................ 7-10
7.4.14 Show/Hide NIBP List ....................................................................................... 7-12
7.4.15 Show/Hide BIS Expand View .......................................................................... 7-12
7.4.16 Show/Hide Device Integration Expand View................................................... 7-12
7.4.17 Display ST Segments ....................................................................................... 7-13
8 Alarm Control .......................................................................................................................... 8-1
8.1 Alarm Structure ............................................................................................................... 8-1
8.2 Alarm Mode .................................................................................................................... 8-1
8.2.1 Audible Alarms..................................................................................................... 8-2
8.2.2 Alarm Messages ................................................................................................... 8-3
8.2.3 Background Color ................................................................................................ 8-3
8.2.4 Parameter Flashes................................................................................................. 8-3
8.3 Alarm Volume ................................................................................................................. 8-4
8.4 Alarm Setup..................................................................................................................... 8-5
8.4.1 Parameter Setup Window ..................................................................................... 8-5
8.4.2 Alarm Setup Window ........................................................................................... 8-5
8.5 Pausing Alarms ............................................................................................................... 8-7
8.6 Resetting Alarms ............................................................................................................. 8-8
9 Review ....................................................................................................................................... 9-1
9.1 Online Review................................................................................................................. 9-1
9.1.1 Dynamic Short Trend ........................................................................................... 9-1
9.1.2 Trend Review ....................................................................................................... 9-2
9.1.3 Full Disclosure ..................................................................................................... 9-4
9.1.4 C.O. Review ....................................................................................................... 9-14
9.1.5 Event Review ..................................................................................................... 9-15
9.1.6 12-Lead Review ................................................................................................. 9-19
9.1.7 ST Review .......................................................................................................... 9-20
9.2 Discharged Patients ....................................................................................................... 9-22
9.2.1 All Patients ......................................................................................................... 9-23
10 Calculation ............................................................................................................................ 10-1
10.1 Drug Calculation ......................................................................................................... 10-1
10.2 Hemodynamics Calculation ........................................................................................ 10-4
10.3 Oxygenation Calculation ............................................................................................. 10-5
10.4 Ventilation Calculation ................................................................................................ 10-7
10.5 Renal Calculation ........................................................................................................ 10-8
11 Record, Print and Save As ....................................................................................................11-1
11.1 Record ..........................................................................................................................11-1
BeneVision CMS Operator‟s Manual
3
11.1.1 Installing Recorder Paper ..................................................................................11-4
11.1.2 Recorder Operations ..........................................................................................11-6
11.1.3 Recording Control .............................................................................................11-9
11.2 Print ............................................................................................................................11-10
11.2.1 Printing Support ..............................................................................................11-10
11.2.2 Printing Contents .............................................................................................11-10
11.2.3 Printing Operations.......................................................................................... 11-11
11.2.4 Printing Control ...............................................................................................11-19
11.3 Save As .......................................................................................................................11-20
12 System Setup......................................................................................................................... 12-1
12.1 General Setup .............................................................................................................. 12-1
12.2 Admin Setup ................................................................................................................ 12-3
12.2.1 Setting Color .................................................................................................... 12-3
12.2.2 Display Setup ................................................................................................... 12-4
12.2.3 Alarm................................................................................................................ 12-8
12.2.4 Trend Group ..................................................................................................... 12-9
12.2.5 Monitor List (CentralStation Only) ................................................................ 12-10
12.2.6 Telemetry (CentralStation Only) .....................................................................12-11
12.2.7 Log ................................................................................................................. 12-14
12.2.8 Other............................................................................................................... 12-15
12.3 Communication Settings ........................................................................................... 12-21
12.3.1 Network Setup................................................................................................ 12-21
12.3.2 CentralStation Authorization (CentralStation Only) ...................................... 12-22
12.3.3 Bed Authorization (CentralStation Only) ....................................................... 12-22
12.3.4 CentralStation Connection ............................................................................. 12-23
12.3.5 Gateway Communication Setting (CentralStation Only) ............................... 12-23
13 Paging .................................................................................................................................... 13-1
13.1 Overview ..................................................................................................................... 13-1
13.2 Accessing Paging Window .......................................................................................... 13-1
13.3 Basic Operations ......................................................................................................... 13-2
13.3.1 Adding a Pager ................................................................................................. 13-2
13.3.2 Assigning an Existing Bed to a Pager .............................................................. 13-2
13.3.3 Assigning a New Bed to a Pager ...................................................................... 13-2
13.3.4 Removing a Bed Assignment ........................................................................... 13-3
13.3.5 Editing a Pager ................................................................................................. 13-3
13.3.6 Removing a Pager ............................................................................................ 13-3
13.4 Resending a Failed Page ............................................................................................. 13-4
14 Remote CMS......................................................................................................................... 14-1
14.1 Overview ..................................................................................................................... 14-1
14.2 Remote CMS Viewbed Window ................................................................................. 14-2
14.2.1 Beds List .......................................................................................................... 14-2
4
BeneVision CMS Operator‟s Manual
14.2.2 Physiological Alarm Area................................................................................. 14-3
14.2.3 Technical Alarm Area ....................................................................................... 14-3
14.2.4 Alarm Icon Area ............................................................................................... 14-3
14.2.5 Button Area ...................................................................................................... 14-3
14.2.6 Waveform Area................................................................................................. 14-4
14.2.7 Parameter Area ................................................................................................. 14-4
14.3 Remote CMS Review .................................................................................................. 14-4
14.4 Network Setup and Authorization ............................................................................... 14-4
15 Database Backup and Recovery ......................................................................................... 15-1
15.1 Overview ..................................................................................................................... 15-1
15.2 Backup Database ......................................................................................................... 15-2
15.2.1 Select Operation Type ...................................................................................... 15-2
15.2.2 Select Backup Path ........................................................................................... 15-2
15.2.3 Backup Database .............................................................................................. 15-2
15.3 Recover Database ........................................................................................................ 15-3
15.3.1 Select Operation Type ...................................................................................... 15-3
15.3.2 Select Path ........................................................................................................ 15-3
15.3.3 Recover Database ............................................................................................. 15-3
15.4 Rebuild Database ........................................................................................................ 15-4
15.5 Shrink Database .......................................................................................................... 15-4
15.6 Exit Database Backup and Recovery .......................................................................... 15-4
16 System Help .......................................................................................................................... 16-1
16.1 Overview ..................................................................................................................... 16-1
A Technical Specifications ......................................................................................................... A-1
A.1 Requirements................................................................................................................. A-1
A.2 Recorder ........................................................................................................................ A-2
A.3 Audio Signals ................................................................................................................ A-2
A.4 Wired Network .............................................................................................................. A-2
A.5 Review........................................................................................................................... A-2
A.6 Calculation .................................................................................................................... A-3
A.7 Save As .......................................................................................................................... A-3
A.8 Display .......................................................................................................................... A-3
A.9 Print ............................................................................................................................... A-3
A.10 Record ......................................................................................................................... A-4
A.11 Data Export.................................................................................................................. A-4
B CMS Alarms............................................................................................................................. B-1
C Units, Symbols, Terms and Formulas ................................................................................... C-1
C.1 Units ............................................................................................................................... C-1
C.2 Symbols .......................................................................................................................... C-2
BeneVision CMS Operator‟s Manual
5
C.3 Abbreviations.................................................................................................................. C-2
C.4 Formulas ......................................................................................................................... C-8
D Anomaly .................................................................................................................................. D-1
6
BeneVision CMS Operator‟s Manual
1 Safety
1.1 Safety Information
The safety statements presented in this chapter refer to the basic safety information that the
operator of the BeneVision Central Monitoring System (hereinafter called CMS) shall pay
attention to and abide by. There are additional safety statements in other chapters or sections,
which may be the same as or similar to the following, or specific to the operations.
WARNING

Indicates a potential hazard situation or unsafe practice that, if not avoided, could
result in death or serious injury.
CAUTION

Indicates a potential hazard or unsafe practice that, if not avoided, could result in
minor personal injury or product/property damage.
NOTE

Provides application tips or other useful information to ensure that you get the
most from your product.
BeneVision CMS Operator‟s Manual
1-1
1.1.1 Warnings
WARNING
1-2

The device is intended for use only by clinical professionals or under their
guidance. It must only be used by persons who have received adequate training
in its use. Anyone unauthorized or untrained must not perform any operation
on it.

The physiological waveforms, parameters and alarms displayed on the CMS
screen are for clinician‟s reference only and cannot be directly used as the basis
for clinical treatment. Before giving invasive treatment to a patient, you must go
to the corresponding monitor to confirm the results you have obtained from the
CMS.

If any value displayed on the screen of the CMS is abnormal or questionable,
first determine the patient‟s vital signs by alternative means and then verify that
CMS or monitor is working correctly.

The CMS is a clinical information device. Except for using such components as
the mouse, touchscreen and keyboard to perform normal operations, do not
touch or disassemble any other component, especially the power component;
otherwise, it may result in personnel injury.

The computer running the CMS software must comply with local relevant
regulations. The CMS is intended to connect Mindray monitors or telemetries
only. Connecting the monitors made by other manufacturers may cause the
values displayed on the CMS to be inaccurate.

The service life of the CMS depends on its hardware. Rough treatment,
dropping or collision should be avoided in the operation of the keyboard, mouse
and computer; otherwise, the service life of the CMS may be shortened.

Components of the CMS, such as the keyboard and mouse, may be
contaminated by microorganisms during transport, storage and use. Before
removing them from their packaging, the packaging should be inspected for
damage. In case of any damage, contact the carrier or our company
immediately.

The CMS can construct a wireless local area network (WLAN) by connecting
monitors. When data is transmitted via wireless radio frequency (RF) signals, it
may impair the environment or the use of other equipment. Therefore, the
wireless RF equipment must comply with CE, FCC and other local relevant
standards and regulations.

When the CentralStation is transmitting data via wireless RF signals, loss of
patient data may be caused by the interference of other RF signals.

Data communication must be performed within a closed network for all network
functions.

If an external audio device is connected to CMS, do not turn off the external
audio device or adjust the volume to zero.

Do not block the speaker of the CMS.

Do not rely exclusively on audible alarm system. Setting alarm volume to a low
level may result in a hazard to the patient.

A hazard can exist if different alarm presets are used for the same or similar
equipment in any single area.
BeneVision CMS Operator‟s Manual
1.1.2 Cautions
CAUTION

All CMS equipment must utilize the hospital emergency power system. Failure
to do so will result in loss of monitoring during extended periods of power
failure. Hospitals without an emergency power system should use an
Uninterruptible Power Supply (UPS) to power the CMS. When there is a power
failure, the system should be shut down by following the specified shutdown
procedure before the UPS is turned off. If the system has a sudden power
failure, system failure may occur and consequently the system will not work
correctly next time or may even have a serious result.

Start or transport the CMS host and display in their specified environment.
Otherwise, the CMS may be damaged. We will assume no responsibility for such
damages.

System time should be set before the CMS is put into use. If the system time is
changed when the CMS is in use, it may result in patient data loss.

Be sure to use standard thermal recorder paper only, otherwise the recorder
may show poor quality on record, or may be unusable, or the print head of the
recorder may be damaged.

If Windows® 7 Professional Embedded SP1 (32 bits) OS is used, please make
sure that it is only used for the CMS software rather than other purposes.

Using the “Show Desktop” feature in Windows is prohibited. Installing or using
any other software not provided by Mindray is prohibited. Software that has not
been tested or verified by Mindray may cause the instability of the system.
Mindray assumes no responsibility for this.

When printing data through an external printer, be sure to follow the printer‟s
instructions. In case any problem occurs during printing, consult the printer‟s
instructions.

To ensure the safety and stability of the network, the LAN connecting the CMS
and the monitors should be a closed network which is not connected with the
internet or other external networks.
BeneVision CMS Operator‟s Manual
1-3
1.1.3 Notes
NOTE

Keep this manual in the vicinity of the CMS so that it can be easily located when
needed.

During normal use, the operator is expected to face the front of the equipment.

The CentralStation is capable of connecting up to 32 monitors and telemetry
transmitters. The cable connecting the monitor to the switch or exchange cannot
exceed 100 m, otherwise it may result in network overload or weak network
signals and consequently errors will occur during data transmission or while
displaying.

All the CMS host, parts, or accessories should be from Mindray or
acknowledged by Mindray.

The functions through right clicking the mouse cannot be operated on the
touchscreen.
1.2 Equipment Symbols
NOTE

Some symbols may not appear on your equipment.

This manual describes a series of typical computer symbols, which may be
slightly different from what are on your computer. The computer symbols
usually have their specific meanings. Refer to your computer‟s operator‟s
manual or contact our service personnel if you have any question.
Symbol
Description
Refer to instruction manual/booklet
CAUTION: To reduce the risk of electric shock, do NOT remove
cover. Refer servicing to qualified service personnel.
Alternating current
Power switch
Keyboard port
1-4
BeneVision CMS Operator‟s Manual
Symbol
Description
Mouse port
Serial communication(COM)port
Display port
Printer port
USB port or device
Network port
Sound output port
Sound input port
Microphone port
DATE OF MANUAFACTURE
MANUFACTURER
Serial number
Equipotentiality
The following definition of the WEEE label applies to EU member
states only.
This symbol indicates that this product should not be treated as
household waste. By ensuring that this product is disposed of correctly,
you will help prevent bringing potential negative consequences to the
environment and human health. For more detailed information with
regard to returning and recycling this product, please consult the
distributor from whom you purchased it.
* For system products, this label may be attached to the main unit only.
BeneVision CMS Operator‟s Manual
1-5
FOR YOUR NOTES
1-6
BeneVision CMS Operator‟s Manual
2 The Basics
2.1 Intended Use
The indications for use of the BeneVision Monitoring System include:
 Real time viewing of patient clinical data and alarms
 Storage and Historical review of patient clinical data and alarms
 Printing of real time and historical patient data
 Configuration of local settings as well as synchronizing settings across the network to a
remote device
 Transfer of patient clinical data and settings between several CentralStations
The BeneVision Monitoring System is a networked patient monitoring system intended for
use in a fixed location, installed in a hospital or clinical environment to provide clinicians
remote patient monitoring. The network connections between the various devices can be any
combination of Ethernet (Wired), Wireless WiFi (WLAN), and Wireless WMTS.
TheBeneVision Monitoring System supports one or more Mindray compatible physiological
monitors and will display, store, print, and transfer information received from the compatible
monitors. The BeneVision Central Monitoring System supports bi-directional configuration
of the compatible monitors. No data processing is done by the BeneVision Central
Monitoring System for data received from compatible monitors.
The BeneVision Monitoring System includes several Telemetry monitoring subsystems all of
which operate in the 608M WMTS frequency range within a defined coverage area. All of the
supported telemetry systems transmit data to the CentralStation for processing, display, and
alarm.
 The TMS-6016 transmitter is intended for use on Adult and Pediatric patients to monitor
ECG and SpO2 physiological data. The CentralStation will support ECG, Heart Rate,
SpO2, Pulse Rate, Arrhythmia analysis, QT monitoring, and ST Segment Analysis for the
TMS-6016.
 The Panorama Telepack-608 transmitter is intended for use on Adult patients to monitor
ECG and SpO2 physiological data. The CentralStation will support ECG, Heart Rate,
SpO2, Pulse Rate, Arrhythmia analysis, QT monitoring, and ST Segment Analysis for the
Panorama Telepack-608.
 The TMS60 transmitter is intended for use on Adult and Pediatric patients to monitor
ECG and SpO2 physiological data. The physiological data can be reviewed locally on the
BeneVision CMS Operator‟s Manual
2-1
display of the transmitter. The CentralStation will support ECG, Heart Rate, SpO2, Pulse
Rate, Arrhythmia analysis, QT monitoring, and ST Segment Analysis for the TMS60.
The BeneVision Central Monitoring System is intended for use in a hospital or other clinical
environment under the direct supervision of a licensed healthcare practitioner.
WARNING

The device is intended for use by qualified physicians or well-trained clinicians.
Anyone unauthorized or untrained must not perform any operation on it.

The physiological waveforms, parameters and alarms displayed on the screen of
the CMS are for reference only and cannot be directly used as the basis for
clinical treatment.

If any value displayed on the CMS screen is abnormal or questionable, first
determine the patient‟s vital signs by alternative means and then verify that the
CMS, or corresponding monitor or telemetry transmitter is working correctly.
2.2 Contraindications
None.
2.3 CMS Functions & Features
The CMS includes three modules: CentralStation, WorkStation and ViewStation. They vary
in functions.
CentralStation
The CentralStation can display, print, store and review patient clinical data. The clinical data
displayed at the CentralStation is derived from compatible physiological monitor(s) or the
Telemetry Transmitter(s). The compatible monitors are connected to the CentralStation via
the bedside device network.
The CentralStation:
 Is capable of connecting up to 32 monitors.
 Is capable of connecting up to 32 telemetry transmitters.
 Only supports Mindray monitoring devices.
 Provides patient data to multiple WorkStations and ViewStations.
 Supports individual bed (1-32 bed) frequency setup in each telemetry monitoring system.
 Supports multi-screen display mode.
 Is capable of displaying information from 16 monitors in the single-screen mode and 32
monitors in the multi-screen mode.
2-2
BeneVision CMS Operator‟s Manual
 Allows you to view a single patient.
 Supports networking between multiple CentralStations and remote CentralStations.
 Allows you to review up to 240 hours of trend data for each online patient.
 Allows you to review up to 720 events for each online patient.
 Allows you to review a 4-hour dynamic short trend for each online patient.
 Allows you to review up to 720 C.O. measurements for each online patient.
 Allows you to review up to 240 hours of ST segments for each online patient.
 Allows you to review up to 240 hours of waveforms for each online patient.
 Allows you to review up to 240 hours of compressed waveforms for each online patient.
 Allows you to review up to 240 hours of NIBP measurements for each online patient.
 Allows you to review up to 720 12-lead analysis results for each online patient.
 Is capable of storing discharged patients‟ full disclosure waveforms, parameters, alarms,
etc.; allows you to search and review the data of up to 20,000 discharged patients.
 Provides a patient information management function.
 Provides audible and visual alarms.
 Provides the functions of drug calculations, titration table calculations, hemodynamics
calculations, oxygenation calculations, ventilation calculations and renal calculations.
 Provides the ability to record, print and save data.
 Provides comprehensive help information, prompts and operational guidance.
 Provides 1280×1024 high display resolution.
 Provides two waveform display modes: color and mono.
 Facilitates the setup of language, waveform and parameter color.
 Supports such peripherals as the keyboard, touchscreen, mouse, thermal recorder, laser
printer, speaker, etc.
 Supports wired and wireless network.
 Provides data output meeting the HL7 protocol. Refer to eGateway HL7 Reference
Manual for details. To obtain this protocol, contact your local Mindray service
representative or Mindray Customer Service Department.
 Supports receiving the data generated during interruption from networked monitors and
combining the data.
 Supports the redundancy backup with two hard disks on the host computer.
 Supports paging.
BeneVision CMS Operator‟s Manual
2-3
WorkStation
WorkStation provides the capability to display and manage patient data (including digital data
and waveform) with assigned monitoring devices. All the patient data comes from the
CentralStation. Most significant configuration changes can be made on the WorkStation.
 Is capable of monitoring up to 32 patients.
 Supports remote view of the patient parameters, waveforms, and alarms from monitors or
telemetries admitted by the CentralStations.
 Allows you to enter or change patient demographic information, change alarm limits and
priorities, discharge patients etc., if authorized.
 Allows you to print patient reports.
ViewStation
The ViewStation provides the capability to display patient data (including digital data and
waveform) with assigned monitoring devices. All the patient data comes from the
CentralStation.
 Is capable of monitoring up to 32 patients.
 Supports remote view of the patient parameters, waveforms, and alarms from monitors or
telemetries admitted by the CentralStations.
 Allows you to print patient reports.
NOTE

2-4
Do not exchange the USB dongles. The USB dongle is used to configure the
optional system functions which may be different for different CMS systems.
BeneVision CMS Operator‟s Manual
2.4 Components
The CMS equipment consists of system software, computer, hardware dongle, network
devices (optional), recorder (optional), printer (optional) and UPS (optional).
2
1
4
3
5
Figure 2-1 CentralStation
As shown above, a typical CentralStation mainly consists of the following components:
1.
Display
2.
Host computer (a tower computer or a 2U server)
3.
Keyboard
4.
USB dongle
5.
Mouse
NOTE

The CentralStation, WorkStation or ViewStation can be equipped with up to four
external displays.

The WorkStation and ViewStation have the same components as CentralStation.

This manual is written based on the maximum configuration. Some contents may
not apply to your system.
BeneVision CMS Operator‟s Manual
2-5
2.5 Networking Mode
The typical networking diagram of the BeneVision monitoring system is shown below:
Hospital Network
eGateway
CMS Network
CentralStatio
n
CMS
Viewer
Printer
ViewStatio
n
WorkStation
Recorder
Bedside Device
Network
Wired
Network
Wireless
Network
Monitors without
wireless network
adapters
Monitors with
wireless network
adapters
Telemetry
Network
Telemetry
transmitters
Figure 2-2 BeneVision Monitoring Network
 CMS Network
The CMS network consists of CentralStation, WorkStation and ViewStation modules. The
CentralStation is the module that monitors patients, collects and stores data, and performs
alarm notification. The CentralStation transmits the patient data to the WorkStation and
ViewStation.
 Bedside Device Network
The Bedside device network connects the compatible bedside devices. There are three types
of data communication mode to the CentralStation.

Wired network
The CentralStation, exchange and monitors interconnect through a network cable.

2-6
Wireless network
BeneVision CMS Operator‟s Manual
Through a network cable, the CentralStation is connected to an AP (Access Point), which
via wireless RF connects multiple monitors equipped with wireless network adapters.

Telemetry network
Through a network cable, the CentralStation is connected to the telemetry receiver, which via
wireless RF connects multiple telemetry transmitters.
The CentralStation supports the networking between multiple CentralStations so that the
information on one monitor within one CentralStation can be viewed by other networked
CentralStations.
2.6 Controls
2.6.1 Mouse
Left Mouse
Button
The mouse is the primary means of user interaction with the CMS. There are two basic ways
to operate the mouse:
 Click: position the mouse pointer on a selection, and then press and immediately release
the left mouse button;
 Drag: position the mouse pointer on a selection, and then hold the left mouse button down
while moving the mouse pointer until your desired place is reached.
 Scroll: position the mouse pointer on the scroll bar, and then scroll up or down the mouse
wheel until your desired place is reached.
NOTE

The term “click” in this manual refers to clicking the left mouse button unless
otherwise specified.
Depending on your action, or the mode of operation, the mouse pointer on the screen of the
CMS will be shaped differently:
BeneVision CMS Operator‟s Manual
2-7

When the mouse pointer is arrow-shaped, you can click, drag and move
the cursor.
 | The mouse pointer is shaped like an I-beam when you are in a text
entry field.
2.6.2 Keyboard
The keyboard can be used to enter characters into text entry fields. To enter characters into a
text entry field, position the mouse pointer inside the text entry field and then click the
mouse. When the mouse pointer changes its shape from an arrow to an I-beam, it indicates
that you can type, select, delete text, or reposition the insertion point.
2.6.3 Touchscreen
The touchscreen can be used to directly position, drag, select, or enter the text on the screen
with a touch.
2.6.4 Controls
Scroll Bars
Up arrow
Left arrow
Scroll box
Right arrow
Scroll box
Down arrow
Horizontal scroll bar
Vertical scroll bar
As shown in the figure above, there are two types of scroll bars: horizontal and vertical. The
scroll bar can be used to position, browse and display your desired information.
Text Box
The text box provides text entry fields, which are used to edit and display text. In a text entry
2-8
BeneVision CMS Operator‟s Manual
field, you can use the mouse and keyboard to edit text, input, select, delete, copy and paste
characters.
Radio Buttons
Selected
Unselected
Radio buttons can be used to select one of a group of mutually exclusive options:
 ○
indicates unselected
 ⊙
indicates selected
Command Buttons
Command buttons can be used to execute designated operations. When a command button
appears dimmed or pressed, it indicates that this command button is currently disabled.
Check Boxes
Partly checked
Unchecked
Checked
Check boxes enable the users to select multiple options.



Indicates active selection. If there is more than one sub-item, it indicates that all the
sub-items are selected.
Indicates that this item has multiple sub-items but has only part of them selected.
Indicates that this option is not selected. If there is more than one sub-item, it
indicates that none of them is selected.
BeneVision CMS Operator‟s Manual
2-9
List Box
Title
Scroll bar
A list of options
The list box contains a list of options from which the user can select one or more. If there are
too many options to be displayed in the list box, you can use the scroll bar to display the
hidden options.
Drop-down List Box
Down arrow
Drop-down list
The drop-down list box has a down arrow button next to it, which can be used to open or
close a list of options. You can make a selection from the drop-down list.
Tab Sheet
Tab
You can switch among the tab sheets by clicking the tab.
2-10
BeneVision CMS Operator‟s Manual
Touchscreen Controls
The following controls facilitate screen selection on the touchscreen.
: up arrow
: down arrow
: left arrow
: right arrow
BeneVision CMS Operator‟s Manual
2-11
FOR YOUR NOTES
2-12
BeneVision CMS Operator‟s Manual
3 Installation and Maintenance
3.1 Unpacking and Inspection
Before unpacking, examine the packing case carefully for signs of damage. If any damage is
detected, contact the carrier or Mindray.
If the packing case is intact, open the package and remove the equipment and accessories
carefully.
NOTE

Please save the packaging materials for later transport or storage use.
WARNING

When disposing of the packaging material, be sure to observe the applicable
waste control regulations and keep it out of children‟s reach.

Components of the CMS, such as the keyboard and mouse, may be contaminated
by microorganisms during transport, storage and use. Before removing them
from their packaging, the packaging should be inspected for damage. In case of
any damage, contact the carrier or Mindray immediately.
BeneVision CMS Operator‟s Manual
3-1
3.2 Installation
WARNING

The CMS should be installed by manufacturer designated personnel. The CMS
software copyright is solely owned by Mindray. No organization or individual
shall resort to altering, copying, or exchanging it or to any other infringement on
it in any form or by any means without due permission.
NOTE

Never place the CMS within a patient environment.

Place the CMS in an environment that the system can be easily viewed, operated
and maintained.
3.2.1 Environmental Requirements
Each component of the CMS must work under the specified environment.
The environment where the CMS is installed should be reasonably free from noises,
vibration, dust, and corrosive, flammable, explosive substances. If the CMS is installed in a
cabinet, sufficient space in front and behind should be left for convenient operation,
maintenance and repair. Moreover, to maintain good ventilation, the CMS should be at least
2 inches (5 cm) away from the cabinet.
When the CMS is moved from one place to another, condensation may occur as a result of
temperature or humidity difference. In this case, never start the system before the
condensation disappears.
3-2
BeneVision CMS Operator‟s Manual
3.2.2 Power Requirements
Each component of the CMS must be powered by the specified power source.
To protect hospital personnel from electric shock, the CMS (including the host and displays)
and its recorder must have their casings properly grounded. The host of the CMS is
provided with a 3-wire power cable, which must be plugged into a properly grounded 3wire receptacle. If a 3-wire, grounded receptacle is not available, consult the hospital
electrician.
WARNING

Make sure that the operating environment and power source of the CMS meet
the specific requirements, otherwise unexpected consequences, e.g. damage to the
equipment, may result.

Appropriate power supply must be selected according to the setup of the system
power voltage, otherwise serious damage may be caused to the system.

Never use a 3-wire to 2-wire adapter with any unit of the CMS.
3.3 Starting the System
To start your system:
1.
Perform safety checks before starting your system. For details, refer to 3.5.1 General
Inspection.
2.
Turn on the UPS, if applicable, and power on the system.
3.
Press the power switches on the host to start the operating system and displays.
4.
The system will perform a series of self-tests and displays corresponding information
on the screen.
5.
If the self-tests pass, the system will beep one time and enter the main screen
immediately.
If there is a self-test failure, the system will beep and display an error message.
CAUTION

To prevent damaging the system from a sudden power failure, it is recommended
that your CMS is equipped with a UPS.
NOTE

If the computer host beeps during self-tests or startup, consult the manual
provided with the computer for assistance or contact Mindray.
BeneVision CMS Operator‟s Manual
3-3
3.4 Shutting Down the System
It is important to properly shut down the system to prevent inadvertent errors from
occurring.
To shut down the system:
1.
Click “System Setup” button.
2.
Select “Shutdown” button from “General Setup” menu.
3.
The system will check if any patients are being monitored:

If no patients are being monitored, go to the next step.

If patients are still being monitored, the message “× patients are being monitored.
Are you sure you want to shut down?” will be displayed. You can either select
“Yes” to begin the next step, or select “No” to close the message box and stop the
shutdown process.
4. A message box asking whether to shut down the system will be displayed. Select “Yes”
from the message box.
5.

If no password is required while shutting down the CMS, the CMS, the operating
system and host will automatically shut off.

If a password is required while shutting down the CMS, a dialog box will pop up.
Enter the required password and select “OK”. The CMS, the operating system,
and host will automatically shut off.
Turn off the UPS if one is in use.
6. Disconnect the power cord of each device from the power outlet.
CAUTION

All CMS equipment must utilize the hospital emergency power system. Failure to
do so will result in loss of monitoring during extended periods of power failure.
Hospitals without an emergency power system should use a UPS to provide power
to the CMS. The UPS must not be turned off when the CMS is working. When
there is a power failure, the system should be shut down by following the specified
shutdown procedure before the UPS is exhausted. When the system has a sudden
power failure, system failure may occur, and the system may not work properly
when it restarts.
3.5 Maintenance
WARNING

3-4
Failure on the part of the responsible hospital or institution employing the use of
BeneVision CMS Operator‟s Manual
the CMS to implement a satisfactory maintenance schedule may cause undue
equipment failure and possible health hazard.

The safety checks or servicing involving any disassembly or decomposition of
devices should be performed by professional servicing personnel, otherwise it
may lead to undue equipment failure and possible health hazards.

Turn off the CMS if no patients are to be centrally monitored. If the system has
been running continually for six months, restart the system.

When the CMS is restarting, patient data will not be stored. To prevent any data
loss, only restart your system when there are no patients being centrally
monitored.
3.5.1 General Inspection
Whenever your system is first installed, repaired, upgraded or has been used for 6-12
months, a thorough inspection should be performed by qualified service personnel to ensure
its reliability.
Follow these guidelines:
 Inspect the equipment and its accessories for mechanical damage.
 Make sure the environment and power supply meet the specific requirements.
 Inspect all power cords and signal lines for fraying or other damages, and ensure that
they are properly connected and insulated.
 Ensure the sound system functions normally.
 Ensure each function of the system is in good condition.
In case of any damage or abnormity, do not use the CMS. Contact the hospital biomedical
engineers or Mindray service personnel immediately.
BeneVision CMS Operator‟s Manual
3-5
3.5.2 General Cleaning
WARNING

Be sure to shut down the system and disconnect all power cords from the outlet
before cleaning the equipment.
Your equipment should be cleaned on a regular basis. If you are in an area that is heavily
polluted or dusty, the equipment should be cleaned more frequently. The equipment to be
cleaned includes the host, displays, printer, recorder, keyboard and mouse. Before cleaning
the equipment, consult your hospital‟s regulations for cleaning, disinfecting and sterilizing
equipment.
Cleaning Agents
The exterior surfaces of the equipment may be cleaned with a clean and soft cloth, sponge
or cotton ball, dampened with a non-erosive cleaning solution. Drying off excess cleaning
solution before cleaning the equipment is recommended. The following are examples of
cleaning solutions:
 Hydrogen peroxide (3%)
 Ethyl alcohol (70%)
 Host cleaning solutions
 Liquid crystal display (LCD) detergent
3-6
BeneVision CMS Operator‟s Manual
Follow these guidelines to avoid damaging the equipment:
CAUTION

Failure to follow these guidelines may melt, distort, or dull the finish of the case,
blur lettering on the labels, or cause equipment failures.
 ALWAYS dilute the solutions according to the manufacturer‟s suggestions.
 ALWAYS wipe off all the cleaning solution with a dry cloth after cleaning.
 NEVER SUBMERGE the equipment into water or any cleaning solution, or POUR or
SPRAY water or any cleaning solution on the equipment.
 NEVER permit fluids to run into the casing, switches, connectors, or any ventilation
openings in the equipment.
 NEVER use abrasive materials, or erosive, acetone –based cleaning agents.
WARNING

Disinfection or sterilization may cause damage to the equipment.Therefore, when
preparing to disinfect or sterilize the equipment, consult your hospital‟s Infection
Control Officer or Epidemiologist.

The indicated cleaning solutions should only be used for general cleaning.
Mindray cannot assume any responsibility if these cleaning agents are used for
infection control.
BeneVision CMS Operator‟s Manual
3-7
FOR YOUR NOTES
3-8
BeneVision CMS Operator‟s Manual
4 Display
4.1 Overview
The CMS can support single-screen or multi- screen display modes.
4.2 Single-Screen Mode
4.2.1 Main Screen
In single-screen mode, up to 16 patients can be viewed simultaneously. Figure 4-1 below
shows the main screen in the single-screen mode.
A
1
2
3
4
B
5
6
7
8
C
Figure 4-1 Main Screen in Single Screen Mode
A.
System information area
B.
Patient window area
Tiles 1-7 are spot patient windows, and Tile 8 is non-spot patient window.
C.
System button and icon area
BeneVision CMS Operator‟s Manual
4-1
NOTE

In single-screen mode, a maximum of 16 patients can be viewed simultaneously. If
there are more than 16 but less than 32 patients being monitored on the
CentralStation, we recommend you to use multi- screen mode.
System Information Area
In this area, the following information is displayed:
Hospital information:
System alarm area:
Displays the hospital and area where the CMS is located.
Displays the system prompts or alarms. If more than one
message occurs, they will scroll. Please refer to Appendix B for
all the system alarms.
Displays the current time.
Current time:
Patient Window Area
For details, refer to 6.3 Patient Window.
System Button and Icon Area
System buttons include:
Button
Description
System Setup
Click to enter the “System Setup” window.
Discharged Pat.
Click to enter the “Discharged Patients” window. This button is
only available on the CentralStation.
Remote CMS
Click to enter the “Remote CMS” window. This button is only
available on the CentralStation.
Main Screen
/ViewBed:
Click to close the auxiliary screen and return to the main screen./
Click to enter the auxiliary screen.
Paging
Click to enter the “Paging” window which is password protected.
This button is only available on the CentralStation.
Device Assignment
Click to enter the “Device Assignment” window. This button is
only available on the WorkStation and ViewStation.
4-2
BeneVision CMS Operator‟s Manual
System icons include:
No.
Icon Name
Icon
Description
1
Alarm List
Shows the alarms of all monitored patients within the
specified time range.
2
USB state
Indicates that the system is connected to a USB storage
device. This icon will not appear when only the USB
dongle is connected.
Indicates that the printer can be used. Select it to access
“Print Control” tab.
3
Printer state
Indicates a printer error.
Indicates that no printer is connected.
Indicates that the recorder can be used. Select it to access
“Record Control” tab.
4
Recorder state
Indicates that the recorder is undergoing a self-test.
Indicates a recorder error.
Indicates that no recorder is connected.
5
Device
Connection
List
Shows the connection status of admitted devices by the
CentralStation. This icon is only available on the
CentralStation.
Indicates that the network is connected.
6
Network status
Indicates that the network is disconnected.
Indicates that the storage system is in a normal state and the
data is protected from a disk failure.
7
Storage system
status
Indicates that the storage system is in a warning state and
data may be at risk.
Indicates that the storage system is in an error state and
data may be lost.
Indicates that the storage system is in a busy state while an
operation is in progress.
BeneVision CMS Operator‟s Manual
4-3
4.2.2 Auxiliary Screen
Auxiliary
Screen
Figure 4-2 Auxiliary Screen in Single-Screen Mode
In single-screen mode, you can enter the auxiliary screen by clicking a patient window. As
shown in Figure 4-2, the auxiliary screen will occupy the lower part of the screen. The
system will automatically adjust the size and number of patient windows in this mode.
NOTE

4-4
For more information about the tab sheet, refer to 2.6.4 Controls.
BeneVision CMS Operator‟s Manual
4.3 Multiple Screen Mode
When CentralStation, WorkStation or ViewStation is configured with more than one display,
you can set the number of the displays which are to be used for main screen.
 If there are two displays, one or two displays can be set for main screen.
 If there are three displays, two or three displays can be set for main screen.
 If there are four displays, three or four displays can be set for main screen.
Refer to 12.2.2 Display Setup-Number of Main Screen for setting the main screen number.
Take two displays as an example.
 Both displays are set for main screen.
As shown in Figure 4-3, both displays default to the main screen. The system buttons and
icons are located on the right display‟s screen.
Click a patient window, and the right display will change to show the auxiliary screen for this
patient. To go back to the main screen, click the “Main Screen” button at the bottom of the
auxiliary screen.
In two main screens mode, a maximum of 32 beds can be viewed at one time.
××××
××
××××
××
××
98
××
××
××
××
××
××
××
60
××
××
××
××
××
××
××
60
××
98
××
98
××
××
60
××
××
60
60
××
××
××
××
××
××
60
××
××
60
98
98
××
××
××
××
60
60
98
××
××
98
××
××
98
××
××
98
××
60
××
60
××
××
98
98
××
60
××
60
98
××
××
××
××
××
××
××
××
60
98
××
××
98
××
60
××××
××
××
98
××
××
××××
××
××
××××
××
××
××
××
××××
Figure 4-3 Two Main Screens (Default)
 One display is set for main screen.
As shown in Figure 4-4, the left display always shows the main screen and right display
always shows the auxiliary screen. In this mode, up to 16 beds can be viewed at one time.
BeneVision CMS Operator‟s Manual
4-5
×××
××
××××
××
××
98
××
××
60
××
60
××
98
××
98
××
××
60
××
××
98
98
××
××
60
××
××
60
××
60
××
××
××
××
××
98
××
××
××
××
××××
××
98
××
××
×××
××
60
98
××
××
××
××
××
60
××
××
××
××
××
×××
××××
Figure 4-4 One Main Screen
4.4 Assigning a Device on WorkStation and
ViewStation
Select the desired device on the BeneVision Monitoring Network to be displayed on the
WorkStation and ViewStation. If the patient is connected, the patient data then displays on the
WorkStation and ViewStation.
To assign a device to a WorkStation or a ViewStation, follow this procedure.
4-6
1.
Select “Device Assignment” button in the system button area. A password may be
required. Refer to 12.2.2 Display Setup for enabling or disabling the password
protection.
2.
On the left side of the pop-up screen, select a desired CentralStation from the
“CentralStation Name” drop-down list. The admitted devices on that CentralStation will
be displayed.
3.
Select one device.
4.
On the right side of the screen, select a display tab. For example, “Display#1”.
5.
Select one tile on that display tab sheet.
6.
Left click the mouse, and select “Assign”. The device will appear in the display tab
sheet.
7.
If you want to cancel an assigned device, select the device in the display tab sheet, left
click the mouse, and then select “Unassign”.
BeneVision CMS Operator‟s Manual
5 Patient Management
The CentralStation, WorkStation and ViewStation have different patient management
capabilities.
The CentralStation enables you to manage patients by:
 Obtaining patient information
 Synchronizing patient information
 Modifying patient information
 Discharging patients
 Switching patient windows
 Changing to idle sector
 Transferring patients
 Finding a patient
The WorkStation enables you to manage patients by:
 Viewing patient information
 Modifying patient information
 Discharging patients
 Switching patient windows
Some functions need to be enabled in “System Setup” menu. Refer to 12.2.8.7 Remote
Control Settings (CentralStation and WorkStation Only) for enabling these functions.
The ViewStation enables you to manage patients by:
 Viewing patient information
 Switching patient windows
BeneVision CMS Operator‟s Manual
5-1
5.1 Monitoring a Patient
Once the patient is monitored on the CentralStation, the CentralStation can display the
patient‟s physiological parameters, waveforms and alarm messages and store the
corresponding patient data.
5.1.1 Using a Monitor
To monitor a patient, a monitor can be admitted or select.
Admitting a Monitor on CentralStation
To admit a monitor on the CentralStation:
1.
Select “System Setup” button.
2.
Select “Admin Setup” button.
3.
Select “Monitor List” Tab.
4.
In the monitor list, find and select the monitor used by the patient.
5.
Select “Admit” button.
After the monitor in the “Monitor List” is admitted by the CentralStation, the monitor is
assigned to a patient window according to the sequence of left to right and top to bottom.
Then the patient window is bound with the monitor. When the monitor is online again, the
patient data from this monitor will be displayed in the same patient window. For details on
patient window, refer to 6.3 Patient Window.
Selecting a CMS on a Monitor
You can select and connect a desired CMS on the monitor for central monitoring. For how to
connect a CMS, refer to the corresponding monitor‟s operator‟s manual.
NOTE

5-2
Select a CMS on a monitor for central monitoring only when the monitor
supports this function.
BeneVision CMS Operator‟s Manual
5.1.2 Using a Telemetry
The telemetry patient can be monitored on the CentralStation after the telemetry is admitted
by the CentralStation, and then the patient may need to be admitted. Whether or not the
patient needs to be admitted depends on what telemetry system is used.
TMS-6016
For the patient connected to a TMS-6016 transmitter, you can only admit the patient at the
CentralStation.
1.
Admit the transmitter in the “Monitor List” tab.
2.
Click a spot patient window with “Idle Sector” to display a pop-up menu.
3.
Click “Admit Telemetry Patient”, and then select the desired transmitter name (such as
TEL XXXX) to admit the patient.
TMS60
For the patient connected to a TMS60 transmitter, follow this procedure to admit the patient.
1.
Turn on the TMS60 to start monitoring the patient.
2.
Check whether the transmitter name displays in the “Monitor List” tab or not.

If the transmitter name displays in the “Monitor List” tab, click the “Admit” button.

If the transmitter does not display in “Monitor List” tab, follow the steps below:
a. Click a spot patient window with “Idle Sector” to display a pop-up menu.
b. Click “Admit Telemetry Patient”, and then select the desired transmitter name to admit
the patient.
Telepack-608
For the patient connected to a Telepack-608 transmitter, you can admit the transmitter from
the “Monitor List” tab, and then turn on the transmitter to start monitoring the patient.
After telemetry is admitted by the CentralStation, the telemetry can be bound with a patient
window, or not. Refer to 12.2.6 Telemetry (CentralStation Only) for setting monitoring
mode. If telemetry is not bound with the patient window, the patient information from the
telemetry will be displayed in an idle patient window, if one is available. The patient window
is assigned according to the sequence of top to bottom and left to right.
BeneVision CMS Operator‟s Manual
5-3
NOTE

When there is no monitoring device online, an alarm message “No bed is online.
Please check network connection.” will be shown.

If the admitted device‟s number exceeds the maximum number of patients
allowed to a CentralStation, the message “The maximum number of beds
connected is reached” will be displayed. At this time, the CentralStation cannot
admit another device. If you need to admit a device, perform the “Cancel”
operation first. For details, refer to 12.2.5 Monitor List.

On the LAN, the patient on the bedside monitor can be admitted to any
CentralStation, but can only be admitted to one CentralStation.
5.1.3 Auto Waveform Storage
By default, the CentralStation will store five waveforms with the descending priority of ECG
1, ECG 2, ECG 7, Pleth and Plethb each time a patient is connected.
If waveforms in channel ECG 1, ECG 2, ECG 7, Pleth and Plethb are unavailable, waveforms
will not be automatically saved. To change the waveforms to be saved, refer to 9.1.3
Waveform Review for detail.
NOTE
5-4

If you change ECG lead type through the bedside monitor after the waveforms
have been automatically saved on the CentralStation, the waveforms stored in
channel ECG 1, ECG 2 and ECG 7 may also change.

When a patient is discharged, the waveform storage configurations are saved
and the same waveform configuration is used the next time a patient is
connected. If you discharge a patient and set the bed as an idle sector, the
waveform storage settings are cleared, and the waveform configurations are
restored to the system defaults.
BeneVision CMS Operator‟s Manual
5.2 Obtaining Patient Information
Patient information from a Hospital Information System (HIS) system can be obtained
through the eGateway and will display on the current CentralStation/WorkStation.
There are two ways to obtain patient information:
 Admit/Discharge/Transfer (ADT) Query:
a. Click the “Obtain Patient Information” button and the “ADT System Patient
Information” menu is displayed.
b. Input a query condition for Patient ID, last name, first name or unit, and then click the
“Query” button. The queried patient information is displayed.
c. Select a patient from the patient information list. Click the “Import the Patient to
CMS” button. The corresponding patient information in the CentralStation/WorkStation
will be updated.
d. Click the “Exit” button to exit the “ADT System Patient Information” menu.
NOTE

The "Obtain Patient Information" button is only available in the "Patient
Mgmt." tab sheet when the “ADT Query" function is enabled in the
“Communication Setting” menu. For “ADT Query” settings, refer to 12.3
Communication Settings.
 Patient Information Quick Query:
Enter patient keywords in the “Patient Mgmt.” tab sheet, and click the “Save” button. The
patient keywords may be patient name, ID, etc., which are defined on the eGateway. The
CentralStation/WorkStation will automatically search for the patient. If the patient is found,
the patient information will automatically be updated to the CentralStation/WorkStation.
NOTE

For the definition of patient keywords, refer to eGateway Integration Manager
Installation Guide (P/N 046-002447-00) if configured with eGateway.
BeneVision CMS Operator‟s Manual
5-5
5.3 Synchronizing Patient Information
When the CentralStation is associated with a HIS system, the CentralStation will
automatically synchronize and update the patient information with the HIS system.
5.4 Modifying Patient Information
There are two ways to modify patient information:
 Modify patient information through the monitor. For more information, refer to the
monitor‟s operator‟s manual.
 Modify patient information through the CentralStation/WorkStation.
For bedside monitors, when the network is properly connected, either party (the monitor, or
the CentralStation/WorkStation) will inform the other party (the CentralStation/WorkStation,
or the monitor) to make modifications accordingly, so that the patient information is kept
consistent between the monitor and the CentralStation/WorkStation.
NOTE

If you have changed patient category through the CentralStation, patient
category on the monitor will be changed accordingly.

If Passport 2, Passport V, Spectrum, Spectrum OR, or V12/21 monitors are
connected to the CentralStation, some patient information cannot be modified
on the CentralStation.
For telemetry, when the TMS-6016 or Telepack-608 is connected, the patient information can
only be modified from the CentralStation/WorkStation, when TMS60 is connected, all patient
information, except patient category and paced status, can be modified from the
CentralStation/WorkStation.
To modify patient information:
1.
Open the “Patient Mgmt.” tab sheet.
To open the “Patient Mgmt.” tab sheet, you can click the spot patient window or the
block in non-spot patient window, and then select the “Patient Mgmt.” tab.
2.
In this tab sheet, you can modify patient information, such as name, gender and height
etc.
3.
After modification, select “Save” to preserve the changes. Then a prompt message may
appear.

5-6
If unit, bed number, patient ID, last name, first name, patient category, or pacer
switch information on the CentralStation conflicts with that on the bedside monitor,
a dialog box will display for you to confirm which information is correct.
BeneVision CMS Operator‟s Manual

If “Nurse Call” and/or “Event” in the telemetry system are set to “Off”, a message
box will be displayed. Select “OK” to preserve the changes or “Cancel” to delete
the changes.
5.4.1 Inconsistent Patient Information between Monitor and
CentralStation
If patient information is modified when the monitor is disconnected from the CentralStation,
and then the monitor is re-connected to the CentralStation, inconsistent patient information
may occur between the CentralStation and monitor. If this happens, a low priority technical
alarm appears in the technical alarm area, and a prompt message simultaneously appears in
the “Patient Mgmt.” tab sheet. In this case, you need to confirm whether to use the patient
information in the CentralStation or monitor.
5.5 Discharging a Patient
Discharging a patient stops monitoring a patient and allows you to monitor a new patient.
There are two ways to discharge a patient on the monitor:
 Discharge a patient through the monitor. In this case, the patient will also be discharged
by the CentralStation/WorkStation and all the patient‟s data will be saved by the
CentralStation. Refer to the monitor‟s operator‟s manual for details about how to
discharge a patient on a monitor.
 Discharge a patient through the CentralStation/WorkStation. In this case, the patient will
also be discharged by the monitor.
If you discharge a patient through the monitor, refer to the monitor‟s operator‟s manual.
For telemetry patient monitoring, the patient discharge method depends on what transmitter is
connected:
 For TMS-6016 and Telepack-608, it can only be performed through the
CentralStation/WorkStation.
 For TMS60, the patient can be discharged at the CentralStation/WorkStation or at the
TMS60. For details about how to discharge a patient on TMS60, refer to the TMS60
Operator‟s Manual.
BeneVision CMS Operator‟s Manual
5-7
If you discharge a patient through the CentralStation/WorkStation, you can follow either of
the two procedures:
 Procedure 1 (applied to spot patients):
1.
Click the drop-down menu in corresponding patient window and select “Discharge
Patient”.
2.
In the pop-up dialog box, select either “Discharge patient and save data” or “Discharge
Without Saving Data”. If “Discharge patient and save data” is selected, the system will
automatically save all monitored data for this patient. If “Discharge Without Saving
Data” is selected, the system will delete all data about this patient after being discharged.
3.
Optional- Some monitor models have a Standby option also. The message “The monitor
enters the Standby mode after the patient is discharged.” will be displayed if your
monitor has this option. Select or deselect this option:
4.

If this option is selected, the monitor will directly enter Standby mode after a
patient is discharged. The option is selected by default.

If this option is not selected, the monitor will automatically admit a new patient
after the previous patient is discharged.
Click the “OK” button.
 Procedure 2 (applied to both spot patients and non-spot patients):
1.
Click the patient window for a spot patient or the block in the last patient window for a
non-spot patient.
2.
Select the “Patient Mgmt.” tab sheet.
3.
Click the “Discharge” button in the “Patient Mgmt.” tab sheet.
4.
Perform Steps 2 through 4 of Procedure 1.
CAUTION

5-8
When the message “The patient data storage space is nearly full. Please delete
some discharged patients.” appears in the system information area, please
backup the database and then delete the data of some discharged patients.
Otherwise, the system will automatically delete the earliest patient‟s data in the
database when the discharged patient storage space is full.
BeneVision CMS Operator‟s Manual
NOTE

When a patient is discharged, the waveform storage configurations are saved
and used again the next time a new patient is being monitored on the same bed.

If you discharge a patient and set the bed as an idle sector, the waveform storage
settings are cleared, and the waveform configurations restore to the system
defaults. Refer to 6.3.2 Spot Patient Windows for the definition of idle sector.
5.6 Switching Patient Windows
To exchange patient windows on the CMS, click the drop-down menu in the patient window
and select “Move Zone to”, then select desired bed number.
5.7 Changing to Idle Sector
If a patient window displays as “No patient admitted or patient transferred”, click the dropdown menu and select “Change to idle sector”, and then confirm the action in the pop-up
window. The patient window will be released as an idle sector. An idle sector indicates that
the patient window is not bound with a specific device. Once a sector is idle, it is available
for a new device..
NOTE

Whether the “No patient admitted or patient transferred” patient window can be
set to an idle sector is dependent on the setting in “Display Setup” in the “Admin
Setup” menu. Refer to 12.2.2 Multibed Display.

When you select the option “Change to Idle Sector”, the settings for this patient
window restore to the defaults.
5.8 Transferring a Patient
During monitoring, a patient may be transferred from one bed (source bed) to another
(destination bed). Transferring a patient ensures that the patient will continue to be
monitored. Once transferred, the patient will be monitored at the new destination bed.
5.8.1 Transferring a Patient on CentralStation
The CentralStation provides a patient transfer function.
BeneVision CMS Operator‟s Manual
5-9
NOTE

If the patient in the destination bed has not been discharged, selecting “Discharge
Destination Bed Patient with Data Saved” and then transferring a patient will
automatically discharge the patient. In this case, make sure the patient in the
destination bed is ready to be discharged before you transfer a patient to it.
To transfer a patient:
1.
Enter the “Patient Mgmt.” tab sheet.
2.
Click the “Transfer” button. The system will open the “Transfer” dialog box.
3.
Select the desired “Destination CMS” and “Destination Bed”.
4.
Select “Combine with Destination Bed Patient Data” or “Discharge Destination Bed
Patient with Data Saved”. These two options will be unavailable if a patient has not been
admitted to the destination bed.

Combine with Destination Bed Patient Data.
The system will transfer the patient data at the source bed to the destination bed and
combine it with the data at destination bed.

Discharge Destination Bed Patient with Data Saved.
The system will discharge the destination bed patient, saving its data before transferring
the source bed patient data to the destination bed.
5.
Click on the “Continue” button.
6.
Select “OK” in the pop-up dialog to transfer the patient to the destination bed. When
transferring patients between different CentralStations, you need to accept the source
CentralStation‟s transfer request at the destination CentralStation.
NOTE
5-10

Selecting “Combining with Destination Bed Patient Data” to transfer a patient may
cause patient data loss if the system time at the source and destination CentralStation
are unsynchronized.

Ensure that the same patient is monitored by both the source and destination beds
when the "Combining with Destination Bed Patient Data" option is selected.
Otherwise, select the "Discharge Destination Bed Patient with Data Saved" option.

When a patient is transferred from one bed to another, the CentralStation will
interrupt bedside monitoring temporarily.

When a patient is transferred within one CentralStation, all of the monitored data
will be transferred along; if the patient transfer is among different CentralStations,
the full-disclosure waveforms and trend data from the last 72 hours, and other
historic data are transferred along.

If there is a version difference between two CentralStations, patient transfer may not
be enabled.

Patients connected to an Accutorr 7 bedside monitor cannot be transferred.
BeneVision CMS Operator‟s Manual
5.8.2 Transferring a Patient on Monitor
When a patient is transferred between bedside monitors by a transport device, the bedside
monitors will inform the CentralStation of the transference. The CentralStation will
automatically operate as follows:
 Transfer the patient to the destination bed.
 Combine the patient data at source bed and data during transference with the data at
destination bed.
5.9 Finding a Patient
If current patient was ever monitored on the same CentralStation and was discharged, the
patient‟s historic data can be found and combined to the current review data.
To find and re-admit a discharged patient, follow this procedure.
1.
Select the patient‟s window.
2.
In the “Patient Mgmt.” tab sheet of the patient, select “Find Patient” button.
3.
In the pop-up screen, enter last name, first name or patient ID, and then click “Search”.
The search results are listed below.
4.
Select a desired patient in the list, and then select “Ok”. A prompt message “Are you
sure you want to re-admit the discharged patient and combine the historic data to the
current?”
5.
Select “Ok”.
BeneVision CMS Operator‟s Manual
5-11
FOR YOUR NOTES
5-12
BeneVision CMS Operator‟s Manual
6 Multibed Screen
6.1 Overview
The multibed screen of the CMS display as follows:
Spot
Patient
Window
Non-spot
Patient
Window
Figure 6-1 Multibed Screen
Each screen of the CMS can display up to 16 patient windows.
On the CentralStation, if the number of devices connected to the CentralStation is no more
than the number of patient windows, all of the patient windows are used for spot observation,
and the window is called spot patient window, and the patient is called spot patient. If not, the
last patient window will be used for non-spot observation, and the window is called non-spot
patient window, and the patients are called non-spot patients.
In single-screen mode, you can view 16 spot patients at one time; in multi-screen mode, you
can view 32 spot patients at one time. The number of the patient windows to be displayed
depends on the display mode defined for the multibed screen. Refer to 12.2.2 Display SetupMultibed View Window Layout for additional information.
BeneVision CMS Operator‟s Manual
6-1
6.2 Screen Layout
The setting for the main screen layout directly configures each patient window‟s size, and the
total number and layout of patient windows. Please refer to 12.2.2 Display Setup for details.
WARNING

If the monitors connected to the CentralStation are more than the patient
windows that can be displayed on the screen, some monitors will be displayed in
the non-spot patient window in which only alarm status can be displayed. To view
the waveforms and parameters of a non-spot patient, you can switch it to spot
patient window. Refer to 6.3 Patient Window for additional information regarding
spot and non-spot patient windows.
6.3 Patient Window
6.3.1 Non-Spot Patient Window
The non-spot patient window shows information including bed number, patient status and
monitor status. For the devices displayed in this window, different background colors
represent different statuses. In the following figure, “XX” represents a bed number.
1
2
××
××
××
4
××
××
××
7
××
××
××
8
Figure 6-2 Non-Spot Patient Window
9
5
3
6
The following table shows the available status messages and what they indicate.
Item Non-spot patient device status
Indication
1
Device is connected and no alarm is
present.
Background is black.
2
Device is connected and a medium
priority alarm(s) is present.
Device is connected and a low priority
alarm(s) is present.
Background is flashing yellow.
4
Device is connected and a high priority
alarm is present.
Background is flashing red.
5
Disconnected
6
Disconnection alarm occurs.
3
6-2
Background is flashing cyan.
is displayed. Background is black.
is displayed. Background is flashing cyan.
BeneVision CMS Operator‟s Manual
Item Non-spot patient device status
Indication
7
Nurse call occurred.
is displayed. Background is flashing red.
8
Event occurred.
is displayed. Background is flashing red.
9
Standby
is displayed. Background is black.
CAUTION

Since a non-spot patient window presents neither waveform nor parameter to
the clinician, it should not be used for monitoring patients.
NOTE

The user can adjust the display layout at any time to convert a non-spot patient
window to a spot patient window where they will be able to view the patient's
real-time data.
6.3.2 Spot Patient Windows
In the process of monitoring, the spot patient window may stay in one of the following
statuses:
 “No patient admitted or patient transferred” indicates that no patient is admitted to the
monitor or patient was transferred to another monitor.
 “Offline” indicates that this patient window has a patient admitted but its corresponding
monitor may be turned off or disconnected from the CentralStation.
 The patient window is in monitoring status: Indicates that the patient window has an
assigned monitor, a monitored patient, and is communicating with the CentralStation.
 “Standby” indicates that the monitor or telemetry transmitter has entered the Standby
mode.
 “Idle sector” indicates that the patient window is available for bonding with a device.
BeneVision CMS Operator‟s Manual
6-3
6.3.3 Patient Window in Monitoring Status
When a patient window is in the monitoring status, it displays real-time patient data
transmitted from the monitor, including a maximum of 4 waveforms and 5 parameters. In an
individual patient window, the number of waveforms and the layout of parameters are subject
to the display format set for the multibed screen as shown in Figure 6-3.
1
2
3
4
6
5
1. Bed mark & drop-down menu button
4. Physiological alarm area
2. Alarm icon area
5. Waveform area
3. Technical alarm area
6. Parameter area
Figure 6-3 Patient Window in Monitoring Status
When a telemetry system is connected, relevant telemetry icons will appear on this screen.
6.3.3.1 Bed Mark
You can modify bed number and bed mark color on the patient management screen to help
identify the specific bed. For details, refer to 5.4 Modifying Patient Information.
On the WorkStation and ViewStation, when placing the cursor at the bed number, the source
CentralStation name will display.
6-4
BeneVision CMS Operator‟s Manual
6.3.3.2 Drop-down Menu Button
Clicking this button will open a drop-down menu, in which you may perform these
operations:
 Alarm Reset: You can select it to silence the existing alarms on the bedside device and on
the CentralStation. Please refer to 8.6 Resetting Alarms.
 Alarm Paused: In the normal status mode, you can select it to pause all alarms for the
current patient for a configurable time period. The default alarm pause time at the monitor
and telemetry is 2 minutes. During the alarm pause, you can select it to reactivate the
paused alarms.
 Standby:

If a telemetry transmitter is connected and is in the normal status mode, you can
select “Standby” to stop displaying, analyzing, storing or recording the current
patient‟s physiological waveforms and data, and to disable all alarms and sounds.
The device ID, battery icon and signal icon remain on the screen. If a telemetry
transmitter is in Standby mode, you can select “Standby” to exit Standby mode.

If a bedside monitor is connected and in Standby mode, selecting “Standby”
removes the bedside monitor from the Standby mode.
 Freeze/Unfreeze: In the normal status mode, you can select “Freeze” to stop the dynamic
waveforms with freeze time and time scales displayed in the waveform area. In the frozen
status, clicking “Unfreeze” will restore the dynamic waveforms.
 Print: You can select it to start real-time printing.
 Record: You can select it to start real-time recording.
 ViewBed: You can select it to enter the “ViewBed” tab sheet.
 Discharge Patient: You can select it to open the “Discharge” dialog box.
 Patient Mgmt.: You can select it to enter the “Patient Mgmt.” Tab sheet.
 Display Setup: You can select it to enter the “Display Setup” tab sheet.
 Alarm Setup: You can select it to enter the “Alarm Setup” tab sheet.
 Big Numerics: In Big Numerics screen, major parameters are displayed in big numerics
for better viewing. In this case, you can switch to normal screen by selecting “Normal
Screen” from the drop-down menu.
 Privacy Mode: Open the “Multibed” menu, select and set current bed or all beds to
Privacy Mode.
 Night Mode: Open the “Multibed” menu, select and set current bed or all beds to Night
Mode, and choose whether to stop NIBP measuring.
 ST Select: Open the “ST Select” menu of the telemetry system, and select the desired ST
to be displayed in the patient window.
 Start/Stop NIBP Measurement: Used to start or stop an NIBP measurement.
 Move zone to: Select to move the current patient window to another patient window.
BeneVision CMS Operator‟s Manual
6-5
On the WorkStation, you can refer to 12.2.8.7 Remote Control Settings (CentralStation and
WorkStation Only) for enabling the functions.
6.3.3.3 Alarm Icon Area
The alarm icon area displays:
 No icon: Indicates that the monitor system sound is normal.

: Indicates that the monitor alarm is paused.

: Indicates that the monitor alarm is turned off.

: Indicates that the monitor alarm sound is switched off.

: Indicates that the monitor alarm system is reset.

Indicates the received signal strength of each telemetry device channel. This
symbol is only available for telemetry devices. For additional information, refer to 6.3.3.8
Telemetry Signs.
6.3.3.4 Technical Alarm Area
The technical alarm area displays:
 The technical alarms and messages coming from monitor or CentralStation.
This area displays the highest technical alarm message. If multiple highest priority messages
exist, they will scroll. The alarms in descending priority are exclusive high priority alarms,
high priority alarms, medium priority alarms, low priority alarms.
Click this area to open the alarm message list which includes all the alarm messages of
different priorities.
6.3.3.5 Physiological Alarm Area
The physiological alarm area displays:
 Physiological alarms coming from bedside or telemetry.
 A message indicating the alarm or physiological state. For example, “Alarm Pause”,
“CPB Mode”.
6-6
BeneVision CMS Operator‟s Manual
 For telemetry, the battery icon
and transmitter name.
This area displays the highest physiological alarm message. If multiple highest priority
messages exist, they will scroll. The alarms in descending priority are exclusive high priority
alarms, high priority alarms, medium priority alarms, low priority alarms.
Click this area to open the alarm message list which includes all the alarm messages of
different priorities.
When alarms are latched, alarm time is displayed; otherwise, the alarm time is not displayed.
NOTE

Different alarm priorities are indicated by different background colors in the
alarm area. Refer to Part 8.2 Alarm Mode for details.

You can view all physiological or technical alarms by positioning the mouse
pointer inside the physiological or technical alarm area and pressing the left
mouse button.

For unknown technical alarms, the message is “XX Technical Alarm”, XX
representing high, medium or low.

For unknown physiological alarms, the message is “XX Phys. Alarm”, XX
representing high, medium or low.
6.3.3.6 Waveform Area
 Displays waveforms transmitted from the monitor.
 Displays the patient‟s name above the first waveform.
 When one or all lethal arrhythmia alarms are set to off, a message of “Lethals Off” will be
displayed under the first ECG waveform. This is applicable when connecting Passport
12M/17M, Passport 8/12, and T1 monitor.
 When the nurse call and/or event function of the telemetry system is switched off, a
message will display the status under the first ECG waveform.
 If a patient‟s paced status has not been set on the monitor, the
icon will flash in the
icon, the “Patient Mgmt.”
waveform area when a pacer pulse is detected. Click the
sheet will pop up. The “Paced” configuration can be configured here. This icon is also
available in the patient‟s ViewBed screen.
 For all telemetries, displays the Nurse Call icon
.
 Only for telemetry TMS-6016, displays the Event icon
BeneVision CMS Operator‟s Manual
.
6-7
6.3.3.7 Parameter Area
This area displays parameter values transmitted from the monitor.
The
icon beside the parameter indicates that parameter alarms are turned off.
6.3.3.8 Telemetry Signs
The telemetry signs include the telemetry icons and transmitter names. The following table
lists all telemetry signs.
Sign name
Sign
Description
This icon is applied for all telemetries.
 After the Nurse Call button is pressed on the transmitter, the
Nurse Call icon will continuously flash and a corresponding
prompt tone will sound. The prompt tone will automatically
terminate after two beeps.
Nurse Call
 If you click this icon, it will be cleared and the prompt tone will
stop.
 An auto recording will be triggered if the Nurse call‟s record
switch is set to “ON” in “Alarm Setup” menu.
 The nurse call will be stored in “Event Review”. Please refer to
9.1.5 Event Review for viewing, recording and printing in
“Event Review”.
This event icon is applied for the TMS-6016 telemetry.
 After the Event button is pressed on the transmitter, the Event
icon will continuously flash and a beep will sound.
 If you click this icon, it will be cleared.
Event
 An auto recording will be triggered if the Event‟s record switch
is set to “ON” in “Alarm Setup” menu.
 The event will be stored in “Event Review”. Please refer to 9.1.5
Event Review for viewing, recording and printing in “Event
Review”.
Battery
This Battery icon is applied for all telemetries.
The icon indicates the remaining battery charge available in the
transmitter. While the battery charge is depleting, the color of the icon
will change accordingly:
 White: indicates the battery is in normal condition.
 Yellow: indicates the battery is low.
 Red: indicates the battery is nearly depleted
6-8
BeneVision CMS Operator‟s Manual
Sign name
Sign
Description
This Signal icon is applied for all telemetries.
The icon indicates the received signal strength for a corresponding
channel. With the received signal strength changing, the number of the
signal bars and the color of the icon will change accordingly.
Signal
 White: indicates the received signal strength is normal.
 Yellow: indicates the received signal strength is weak.
 Red: indicates no signal is received.
The transmitter name represents different meaning when connecting
TMS-6016, TMS60, or Telepack-608 transmitter.
Transmitter
Name
TEL
XXXX
 For the TMS-6016 transmitter, the transmitter name shows as:
TEL plus the last four characters of the serial number on the rear
of the transmitter. For example, when the serial number is
XXXX2583, the transmitter name shows as “TEL 2583”.
 For the TMS60 transmitter, the transmitter name is the same as
the device name set in the “Maintenance” menu at the
transmitter.
 For the Telepack-608 transmitter, the transmitter name is the
same as the transmitter ID attached on the rear of the transmitter.
6.4 Display Setup
Clicking “Display Setup” in the patient window drop-down menu will enter a tab sheet,
where you can configure the “Multibed Waveform Setup” and “Multibed Numeric Setup” for
the current patient window.
6.4.1 Multibed Waveform Setup
On the left of the “Display Setup” tab sheet, you can designate which waveforms are to be
displayed in the current patient window.
 By selecting the checkbox before the waveform name, you can select or deselect this
waveform. Only the selected waveforms can be displayed in the current patient window.
 By selecting the waveform speed beside the waveform name, you can have a list of
available wave speeds (i.e. 6.25 mm/s, 12.5 mm/s, 25 mm/s and 50 mm/s), from which
you can select.
 Select a waveform by clicking on its name and change its order by clicking “Move First”,
“Move Up”, “Move Down” or “Move Last”. Waveform displaying order can be saved.
BeneVision CMS Operator‟s Manual
6-9
NOTE

When a patient is discharged, the multibed settings in “Waveform Selection and
Order” are saved. The waveforms will be displayed using the same default
configurations when a new patient is monitored.

If you discharge a patient and set the bed to an idle sector, the multibed settings
in “Waveform Selection and Order” are cleared, and the waveform
configurations restore to the system defaults.
6.4.2 Multibed Numeric Setup
The default numeric group cannot be modified or deleted. To change the displayed
parameters and their order in the current patient window, you will need to add a new group.
To add a new group:
1.
Click on the “New Group” button, and “New Group 1” will appear under “Default
Group”.
2.
Select “New Group 1” to open the “Select & Order” list.
3.
Select a parameter from the “Select & Order” list. The “Numeric Preview” area will
show the parameter you have just selected. A maximum of 5 parameters are allowed to
be selected.
4. Select a parameter by clicking on its name and change its order by clicking “Move First”,
“Move Up”, “Move Down” or “Move Last”.
5.
Click the “Save Group” button and then select “New Group 1”. The current patient will
show parameters according to the setup of “New Group 1”.
To delete “New Group 1”, you can select “New Group 1” and then click the “Delete Group”
button.
NOTE
6-10

When a patient is discharged, the numeric group selection is saved. The numeric
group will be displayed using the same default configurations when a new
patient is monitored.

If you discharge a patient and set the bed to an idle sector, the selection of the
numeric group is cleared, and the numeric group configurations restore to the
system defaults.
BeneVision CMS Operator‟s Manual
7 ViewBed
7.1 Overview
The CMS allows you to view a single patient through the “ViewBed” screen, in which you
will have an enlarged view of that single patient‟s information, waveforms and values. In this
screen, you can freeze waveforms, review dynamic short trends, view multi-lead ECG
waveforms, record waveforms, etc.
To access the “ViewBed” screen, follow the instructions below:
 For a spot patient, click the left mouse button in its corresponding patient window. The
“ViewBed” screen for that patient will open.
 For a non-spot patient, click on its corresponding block in the non-spot patient window.
The “ViewBed” screen for that patient will open.
When the “ViewBed” window is open, you can switch among different patients by clicking in
the patient window of a spot patient, clicking on the block of a non-spot patient, or selecting
another bed number in the bed drop-down list of the single bed window.
NOTE

In the single-screen mode, the CMS uses the lower half screen to accommodate
the “ViewBed” screen.

In the multi-screen mode, the CMS uses the secondary display screen to
accommodate the “ViewBed” screen.
BeneVision CMS Operator‟s Manual
7-1
7.2 ViewBed Screen
1
2
××
××
4
3
5
6
××
80
××
××
60
30
××
××
80
110
8
7
1. Patient information area
4. Physiological alarm area
7. Waveform area
2. Alarm icon area
5. Function drop-down list
8. Parameter area
3. Technical alarm area
6. View drop-down list
Figure 7-1 ViewBed Screen (Bedside Monitor)
7-2
BeneVision CMS Operator‟s Manual
1
2
3
4
8
7
1. Patient category
4. Physiological alarm area
7. Waveform area
2. Telemetry icon area
5. Function drop-down menu
8. Parameter area
6
5
3. Technical alarm area
6. View drop-down menu
Figure 7-2 ViewBed Screen (Telemetry)
In the patient information area, patient bed number, name, gender and type are displayed. For
description of the physiological alarm area, alarm icon area, technical alarm area and
telemetry icons, refer to 6.3.3 Patient Window in Monitoring Status.
7.2.1 Function Drop-down Menu
The following table lists all function options for the monitoring devices.
Options
Description
Alarm Reset
Used to silence the on-going alarms.
Enter/Exit Alarm Paused State
Enter/Exit Standby Mode
Start/Stop NIBP measurement
Freeze/Unfreeze
Parameter Order
Record
Used to enter or exit alarm paused status. The pause
time is subject to the monitor settings.
Used to enter or exit the STANDBY mode. This option
is available only when connecting the telemetry.
Used to start/stop NIBP measurement.
Used to freeze and unfreeze waveforms.
Used to open the “Parameter Order” dialog box where
you can set the display order of modules.
Used to open the “Record” dialog box.
BeneVision CMS Operator‟s Manual
7-3
Options
Description
Print
Alarm Setup
Used to open the “Print Setup” dialog box.
Used to enter the “Alarm Setup” tab sheet.
For details about each button, refer to 7.4 Basic Operations.
7.2.2 View Drop-down Menu
The following table lists all View options for the monitoring devices.
Options
Description
Show/Hide Alarm Limits
Used to show/hide alarm high/low limits.
Show/Hide Dynamic Trends
Show/Hide Multi-lead ECG
Show/Hide NIBP Table
Show/Hide BIS Expand View
Show/Hide Device Integration
Expand View
Used to show/hide dynamic short trends.
Used to show/hide multi-lead ECG.
Used to show/hide NIBP groups.
Used to show/hide BIS Expand View.
Used to show/hide Device Integration Expand View.
7.2.3 Waveform Area
This area displays parameter waveforms transmitted from the monitoring device. In the
single-screen mode, this area can only accommodate partial parameter waveforms due to
space confines of the screen. However, you can drag the vertical scroll bar to view more.
For all telemetries, displays
for paced on or
for paced off above the first
waveform.
7-4
BeneVision CMS Operator‟s Manual
7.2.4 Parameter Area
This area displays parameter values transmitted from the monitoring device. Each parameter
module occupies a rectangular area, which is hereinafter called parameter window. In the
single-screen mode, this area can only accommodate partial parameter values due to space
confines of the screen. However, you can drag the vertical scroll bar to view more.
NOTE

The waveforms and parameters are consistent between the CMS and the
monitoring devices.

If you change the display order of waveforms and parameters on the monitoring
device, the display order of waveforms and parameters on the CMS will not
change automatically and vice versa.

In case a module of the monitoring device is turned off or a parameter is no
longer being monitored, the corresponding waveforms and parameters displayed
at the CMS will no longer display.
7.3 Parameter Setup
Click a parameter window, and the border of this window will appear highlighted. Clicking
again will open the “Parameter Setup” window.
The Parameter Setup window includes several tabs. Each tab contains the available options of
a parameter. The current tab sheet depends on the parameter window you have selected. For
example, if you click the ECG parameter window, the Parameter Setup window will open,
with the “ECG” tab sheet at the front.

Alarm Setup: Select “Alarm Setup” button to access the “Alarm Setup” window, and set
alarm limit, record on alarm, print on alarm, and paging on alarm for all parameters.
Refer to 8.4 Alarm Setup for details.
 Default: Click this button to restore CMS-related settings to factory default.
For telemetry transmitter, the parameter setup tab sheet is different. For details, refer to the
manual of telemetry monitoring system.
NOTE


When you change the alarm limits of the monitor via the
CentralStation/WorkStation, make sure that the alarm limits settings are
appropriate for your patient. Setting alarm limits to extreme values may cause
the alarm system to become ineffective.
When the remote control on the alarm setup is enabled, the alarm properties
which support bidirectional controls are shown in blue text. The alarm
properties not supporting bidirectional controls are shown in grey text.
BeneVision CMS Operator‟s Manual
7-5
7.4 Basic Operations
7.4.1 Alarm Setup
On the CentralStation or WorkStation, selecting “Alarm Setup” from the “Function” dropdown menu will enter the “Alarm Setup” tab sheet, where you can set parameter alarms,
arrhythmia alarms, arrhythmia alarm threshold and alarm-related settings. For details, refer to
8.4 Alarm Setup.
7.4.2 Resetting Alarms on Monitors
On the CentralStation or WorkStation, selecting “Alarm Reset” from the “Function” dropdown menu can silence the alarm sound on the monitoring device. The on-going alarms are
also reset on the corresponding patient window on the CMS. Please refer to 8.6 Resetting
Alarms.
7.4.3 Pausing Alarms
On the CentralStation or WorkStation, selecting “Enter Alarm Paused State” from the
“Function” drop-down menu will pause all current patient alarms for a period of time, which
is subject to the monitor settings. The alarm pause time for the telemetry is fixed to two (2)
minutes. The corresponding patient window on the CMS will enter alarm paused status. After
the alarm pause time ends, the system will automatically release the alarm pause. You can
also release the alarm pause by selecting the “Exit Alarm Paused State” from the “Function”
drop-down menu.
7.4.4 Controlling a Telemetry to Enter/Exit Standby
On the CentralStation or WorkStation, selecting “Enter Standby Mode” or “Exit Standby
Mode” from the “Function” drop-down menu will have the current telemetry enter or exit the
Standby mode.
 For the TMS-6016 and Telepack-608, the CentralStation notifies the telemetry to enter or
exit the Standby mode.
 For the TMS60, the CentralStation cannot notify the transmitter to enter or exit the
Standby mode. The transmitter can implement the function by iteself. Refer to the TMS60
Operator’s Manual for details.
7-6
BeneVision CMS Operator‟s Manual
7.4.5 Controlling a Bedside Monitor to Exit Standby
On the CentralStation or WorkStation, if a bedside monitor is in Standby mode, click any
place in the ViewBed window. A dialog box of prompt information will pop up. Select “Yes”
in the dialog box and the monitor will exit the Standby mode and resume normal monitoring.
NOTE

The CentralStation or WorkStation can control the bedside monitor by exiting
Standby mode only when the monitor supports this function.
7.4.6 NIBP Measurement
On the CentralStation or WorkStation, once “Start NIBP Measurement” from the “Function”
drop-down menu is clicked, the corresponding bedside monitor will start an NIBP
measurement. During the measuring process, you can select “Stop NIBP Measurement” to
stop the measurement. This option changes accordingly when the bedside monitor starts or
stops an NIBP measurement.
WARNING

Before starting an NIBP measurement by a bedside monitor at the CentralStation
or WorkStation side, be sure that patient type set on the bedside monitor is
correct and NIBP cuff applied is proper.

The remote NIBP meansurement is not supported when connecting the Passport
2, Passport V, Spectrum, Spectrum OR or V 12/21 monitors.
7.4.7 Freeze/Unfreeze Waveforms
Selecting the “Freeze” option from the Function drop-down menu will freeze all dynamic
waveforms in the waveform area.
In this area, freeze time is displayed at the top of the waveform area and time scale (unit: s)
below the first waveform. Clicking
or
will move the waveforms backward or forward
one unit (s), and the time scale will change accordingly. You can view more frozen
waveforms by dragging the vertical scroll bar shown in Figure 7-1.
In the frozen status, selecting the “Unfreeze” option will restore the dynamic waveforms.
BeneVision CMS Operator‟s Manual
7-7
7.4.8 Parameter Order
Selecting “Parameter Order” from the “Function” drop-down menu will open a dialog box,
where you can configure the waveform and parameter display order.
The available parameters depend on the monitor's configuration. Select a parameter and then
click “Move Up”, “Move Down”, “Move First” or “Move Last” to adjust its position. Its
waveforms and digital values will change their positions accordingly. Clicking the “Default”
button will restore the default display order of parameters. The display order settings can be
saved.
NOTE

When a patient is discharged, the parameter order configuration is saved. The
parameters will be displayed using the same default configurations when a new
patient is admitted.

If you discharge a patient and set the bed to an idle sector, the parameter order
configuration is cleared, and the waveform configuration restores to the system
defaults.
7.4.9 Record
Selecting “Record” from the “Function” drop-down menu will open the “Record” dialog box,
where you can select up to two waveforms. If the recorder is unusable or no recorder is
connected, this option is disabled.
In the frozen status, the recorded waveforms and parameters are the waveforms and
parameters recorded at time of freezing but not at current time. Please refer to 11.1.3
Recording Control about the settings of recording general options.
7-8
BeneVision CMS Operator‟s Manual
7.4.10 Print
Printing in Real-time
Select “Print” from the “Function” drop-down menu, and the “Print Setup” dialog box will
pop up. In this dialog box, you can select the waveforms to be printed. If the printer is
unusable or no printer is connected, this option will be disabled. Please refer to 11.2.4
Printing Control about the general printing options settings.
Printing 12-Lead ECG
When performing 12-lead ECG monitoring and 12-lead ECG analysis using a bedside
monitor, you can select “Show Multi-Lead ECG” from the “View” drop-down menu to
display the 12-lead ECG waveforms. Select “Print” from “Function” drop-down menu, the
“Print Setup” dialog box will pop up. In this dialog box, you can set the waveform layout as
12×1, 6×2+1 or 3×4+1. If the printer is unusable or no printer is connected, this option
will be disabled.
Printing Multi-Lead ECG
When a patient is being monitored at the bedside using 5-lead ECG, select “Show Multi-Lead
ECG” from the “View” drop-down menu to display the multi-lead ECG waveforms. Select
“Print” from the “Function” drop-down menu to print the ECG waveforms. If the printer is
unusable or no printer is connected, this option will be disabled.
BeneVision CMS Operator‟s Manual
7-9
7.4.11 Show/Hide Alarm Limits
Selecting the “Show Alarm Limits” option from the “View” drop-down menu will show
alarm high/low limits set for all physiological parameters. As shown in Figure 7-3, the alarm
high/low limits are located to the right of the parameters value, with the alarm high limit
above the alarm low limit. You can also hide the alarm limits by selecting “Hide Alarm
Limits” option.
2
1
3
2
1
3
1 Measured parameter values 2 High alarm limits 3 Low alarm limits
Figure 7-3 Alarm High/Low Limits
7.4.12 Show/Hide Dynamic Trends
Select “Show Dynamic Trend” to show dynamic short trends for each physiological
parameter. You can also hide the trend window by selecting “Hide Dynamic Trend” option.
For details on dynamic short trend, refer to 9.1.1 Dynamic Short Trend.
7.4.13 Show/Hide Multi-Lead ECG
Select “Show Multi-Lead ECG” from the “View” drop-down menu to show multi-lead ECG
waveform, or select “Hide Multi-Lead ECG” to hide the ECG waveform. The Multi-lead
ECG screen is shown in Figure 7-4:
7-10
BeneVision CMS Operator‟s Manual
Figure 7-4 Multi-lead ECG
If there is no ECG waveform, or the monitor is set to 3-lead, the multi-lead ECG waveforms
will not be displayed.
Select “Show Multi-Lead ECG”/ “Hide Multi-Lead ECG” to turn on or turn off 12-lead ECG
waveform display when the bedside monitor enters full-screen 12-lead view, as shown in
Figure 7-5 below.
Figure 7-5 12-lead ECG (Standard)
BeneVision CMS Operator‟s Manual
7-11
7.4.14 Show/Hide NIBP List
Select “Show NIBP Table” from the “View” drop-down menu to show the NIBP list in the
waveform area. Each measurement includes Measure Time, NIBP values and PR. You can
also hide the NIBP list by selecting “Hide NIBP Table” option.
7.4.15 Show/Hide BIS Expand View
Select “Show BIS Expand View” from the “View” drop-down menu to show BIS Expand
View, or select “Hide BIS Expand View” to hide BIS Expand View. This option is available
in the menu when the bedside monitor supports the BIS function. In “BIS Expand View”, you
can select to view EEG waveforms, BIS trend and DSA graph. This button is enabled only
when networked monitor supports BISx4 monitoring; otherwise, this option is disabled.
7.4.16 Show/Hide Device Integration Expand View
Select “Show Device Integration Expand View” from the “View” drop-down menu to show
Device Integration Expand View. This option is enabled only when the networked monitor
supports connecting external devices, such as ventilators and anesthesia machines; otherwise,
this option is disabled. All text in Device Integration Expand View appears in white.
You can select to view an individual device or all devices in the Device Integration Expand
View:
 Click one of the individual device tabs and access its corresponding tab sheet. Each tab
sheet provides a “Parameter Display” button. You can use the button to select the desired
parameters for display if necessary.
 Click the “Multi Devices” tab to access the tab sheet. In this sheet, you can view the
parameters from all devices at the same time.
NOTE
7-12

There is no “Multi Devices” tab in Device Integration Expand View when only
one device is integrated with the monitor.

The Device Integration Expand View can include a maximum of 4 individual tab
sheets.
BeneVision CMS Operator‟s Manual
7.4.17 Display ST Segments
Display Real-time ST Segments
In the ECG parameter setup menu, select “Display ST Segments”. In the ViewBed window,
the ECG waveform display area will display ST segments.
 Displays ST segments of one lead when using a 3-lead type;
 Displays ST segments of three leads when using 5-lead and 12-lead types.
Figure 7-6 Display ST Segments of Three Leads
As shown in Figure 7-6 above, real-time ST segments and reference segments are
overlapped. Real-time ST segments and current ST values are displayed in the ECG
parameter color. Reference segments and ST reference values are displayed in white. The ST
segment displays the positions of the ISO point, J point and ST point. These three analysis
points can be set in the CentralStation if necessary, or set on the bedside monitor. For details,
refer to the operator‟s manual for the monitor.
Display ST-segments on the Multi-lead ECG Screen
If the multi-lead ECG screen is accessed, corresponding ST segments are displayed after the
lead waveforms on the multi-lead or 12-lead screen, as shown in Figure 7-7 below:
BeneVision CMS Operator‟s Manual
7-13
Figure 7-7 Display ST Segments on 12-lead ECG Screen
7-14
BeneVision CMS Operator‟s Manual
8 Alarm Control
8.1 Alarm Structure
Alarms, triggered by a vital sign that appears abnormal or by a monitor‟s technical problems,
are sent to the CentralStation by the monitors and then indicated to the users by the
CentralStation. Most of the alarms originally come from the monitors. The alarms coming
from the CentralStation itself are displayed in the patient window‟s technical alarm area or
system alarm area on the upper screen. Please refer to Appendix B CMS Alarms for the
alarm messages.
By nature, the alarms are classified into two categories:
 Physiological alarms, and
 Technical alarms
By severity, the alarms are classified into:
 High priority alarms,
 Medium priority alarms, and
 Low priority alarms
NOTE

For details on alarms, refer to the monitor‟s operator‟s manual.
8.2 Alarm Mode
The CMS gives audible and visual alarms in compliance with international standards.
WARNING

The audible and visual alarms given by the CMS comply with the IEC 60601-1-8
standard. The hospital or institution employing the use of the CMS should give
adequate training to the operators.
BeneVision CMS Operator‟s Manual
8-1
8.2.1 Audible Alarms
This system has three choices of alarm tones and patterns: ISO, Mode 1 and Mode 2. For
each pattern, the alarm tones identify the alarm levels as follows:
 ISO pattern:

High priority alarms:
triple+double+triple+double beep

Medium priority alarms:
triple beep

Low priority alarms:
single beep
 Mode 1:

High priority alarms:
high-pitched triple beep

Medium priority alarms:
double beep

Low priority alarms:
low-pitched single beep
 Mode 2:

High priority alarms:
high-pitched triple beep

Medium priority alarms:
double beep

Low priority alarms:
low-pitched single beep
NOTE

8-2
When multiple patients have alarms of different priorities at the same time, the
system will select the alarms of highest priorities and give alarm tones
accordingly.
BeneVision CMS Operator‟s Manual
8.2.2 Alarm Messages
The CMS alerts the users by giving alarm messages in the physiological or technical alarm
area. Before the alarm messages, asterisks are used to indicate different alarm priorities:
 High priority alarms:
triple asterisks “***”
 Medium priority alarms: double asterisks “**”
 Low priority alarms:
single asterisk “*”
When alarms are latched, alarm time is displayed; otherwise, the alarm time is not displayed.
The high priority alarm messages are in white font, and medium/low priority alarm messages
are in black font. Besides alarm messages, the technical alarm area also displays prompt
messages coming from monitors. Those prompts are in a white font.
NOTE

Some physiological alarms, such as asystole, are exclusive. They have identical
alarm tones with normal high level physiological alarms, but their alarm
messages are displayed exclusively. That is to say, when an exclusive physiological
alarm and a normal high level physiological alarm are triggered simultaneously,
only alarm message of the exclusive physiological alarm is displayed.
8.2.3 Background Color
If a spot patient has an alarm, its corresponding patient window and ViewBed screen will
give an alarm message with different background colors indicating different alarm priorities:
 High priority alarms:
red
 Medium priority alarms: yellow
 Low priority alarms:
cyan
The alarm message background can be set to flash. To switch on the function, refer to 12.2.3
Alarm.
If a non-spot patient has an alarm, its corresponding block will appear in red indicating a
high-priority alarm, yellow indicating a medium-priority alarm, or cyan indicating a lowpriority alarm.
8.2.4 Parameter Flashes
If a patient‟s physiological parameter generates an alarm, this parameter will flash in the
parameter area.
BeneVision CMS Operator‟s Manual
8-3
If the alarm high/low limits of the parameter are displayed in the ViewBed screen, either the
alarm high or low limit will also flash indicating that the parameter exceeds the alarm high or
low limit.
8.3 Alarm Volume
By clicking the “System Setup” button then “General Setup” tab, you can enter the “General
Setup” tab sheet. The CMS provides up to 10 volume levels, increasing from 1 to 10. You can
drag the volume control key to your desired volume. While dragging the volume control key,
the corresponding sound will also be played.
The alarm volume can be configured in the range from Minimum Alarm Volume to 10. Please
refer to 12.2.3 Alarm - Setting Minimum Alarm Volume.
In the “General Setup” tab, you can set high alarm volume. High alarm volume can be set
equal to or louder than the alarm volume. The options are “alarm volume +0”, “alarm
volume+1”and “alarm volume+2”. When a high level alarm occurs, the alarm will sound with
the specified high alarm volume. For example, if the high alarm volume is set to “alarm
volume+1”, and the current level of alarm volume is 5, then the high alarm volume is 6.
NOTE

8-4
If high alarm volume level is greater than 10, the BeneVision Central
Monitoring System will sound it in the volume of 10.
BeneVision CMS Operator‟s Manual
8.4 Alarm Setup
In either the “Parameter Setup” or “Alarm Setup” window, you can define alarm switch,
alarm high/low limits and alarm priority for each parameter.
CAUTION

When you change the alarm limits of the monitor via the
CentralStation/WorkStation, make sure that the alarm limits settings are
appropriate for your patient. Setting alarm limits to extreme values may cause
the alarm system to become ineffective.
NOTE

When you select the checkbox before “Alarm Setup” in the “Remote Control
Settings” menu, the parameter alarm setting properties are controlled
bidirectionally. For example, if the alarm limits have changed on the
CentralStation/WorkStation, the alarm limits on the bedside device will change
simultaneously. Refer to 12.2.8 Other for the details of remote alarm setup.

When the remote control on the alarm setup is enabled, the alarm properties
which support bidirectional controls are shown in blue text. The alarm properties
not supporting bidirectional controls are shown in grey text.

You can only view the alarm settings on the ViewStation.
8.4.1 Parameter Setup Window
Click in a parameter window. The border of the window will appear highlighted when the
window is selected. Clicking again will enter the tab sheet of a certain parameter.
Refer to 7.3 Parameter Setup for details.
8.4.2 Alarm Setup Window
Selecting “Alarm Setup” from the “Function” drop-down menu in the “ViewBed” screen will
enter the “Alarm Setup” tab sheet where you can set the monitored parameters‟ alarm
properties, including parameter alarms, arrhythmia alarms, and arrhythmia alarm threshold
settings.
8.4.2.1 Setting Parameter Alarm
In the “Parameter Alarm Settings” tab sheet, you can set the following alarm properties for all
parameters:
BeneVision CMS Operator‟s Manual
8-5
 Activation state: Select it to switch on/off the current parameter alarms. This is only
available when DPM 3/4/5/6/7, Passport 12M/17M, Passport 8/12, Accutorr 7, and T1
are connected .
 Alarm Priority: Select it to set the alarm priorities of the current parameter alarms to
“High”, “Med”, “Low” or “Message”. This is only available when DPM 3/4/5/6/7,
Passport 12M/17M, Passport 8/12, Accutorr 7, and T1 are connected.
 High limit: Select and enter the high limit. When Passport 2, Passport V, Spectrum,
Spectrum OR or V12/21 monitors are connected, selecting “Off ” in the pop-up keyboard
to switch off the high limit alarm.
 Low Limit: Select and enter the low limit. When the Passport 2, Passport V, Spectrum,
Spectrum OR or V12/21 monitors are connected, select “Off” in the pop-up keyboard to
switch off the low limit alarm.
 Record On Alarm: Switch on/off the real-time alarm recording.

On: A recording is performed when an alarm occurs.

Off: No recording is performed when an alarm occurs.
 Print On Alarm: Switch on/off the real-time alarm printing.

On: A printing is performed when an alarm occurs.

Off: No printing is performed when an alarm occurs.
 Paging On Alarm: Switch on/off the alarm paging.

On: The paging is sent to the pager when an alarm occurs.

Off: No paging is sent to the pager when an alarm occurs.
8.4.2.2 Setting Arrhythmia Alarms
In the “Arrhythmia Alarms” tab sheet, the alarm for asystole, tachycardia and other kinds of
arrhythmia can be set here. The following settings are only available when DPM 3/4/5/6/7,
Passport 12M/17M, Passport 8/12, Accutorr 7, or T1 monitor is connected.
 Alarm priority: The alarm level can be set to “High”, “Med”, “Low” or “Message”.
Specifically, the “Message” level only has text without the indication by audio,
background color and „*‟.
 Activation state: The activation state of each arrhythmia can be set individually.
In addition, the activation state of some arrhythmias can be set as a whole with the buttons of
“All Alarms On”, “All Alarms Off” and “Lethals Only”.
 If the “Lethals Only” button is selected, only the lethal arrhythmia alarms are set to “ON”
and other alarms are set to “OFF”.
 If the “All Alarms On” button is selected, all arrhythmia alarms are set to “ON”.
 If the “All Alarms Off” button is selected, all arrhythmia alarms are set to “OFF”.
8-6
BeneVision CMS Operator‟s Manual
NOTE

If a bedside monitor is connected and the “Lethal Arrh Off” item in the monitor‟s
“Admin Setup” menu is set to “Disable”, the “All Alarms Off” button in the
arrhythmia alarm settings of the central station is inactive.

If a telemetry monitoring system is connected and the “Lethal Arrh Off” item in
the “Telemetry” sheet under “Admin Setup” menu is set to “Disable”, the “All
Alarms Off” button in the “Arrhythmia Alarm” tab is inactive.
 Record On Alarm: Switch on/off the real-time arrhythmia alarm recording.

On: A recording is performed when an alarm occurs.

Off: No recording is performed when an alarm occurs.
 Print On Alarm: Switch on/off the real-time arrhythmia alarm printing.

On: A printing is performed when an alarm occurs.

Off: No printing is performed when an alarm occurs.
 Paging on Alarm: Switch on/off the arrhythmia alarm paging.

On: The paging is sent to the pager when an alarm occurs.

Off: No paging is sent to the pager when an alarm occurs.
8.4.2.3 Setting Arrhythmia Threshold
The threshold for PVCs high limit, tachycardia and others can be set in the “Arrh Threshold
Setup” sheet.
Refer to the monitor or telemetry operator‟s manual for the arrhythmia alarms and their
threshold.
8.5 Pausing Alarms
For monitors supporting bidirectional control of alarm pause, you can select “Enter Alarm
Paused State” from the “Function” drop-down menu in the CentralStation/WorkStation
ViewBed screen or “Alarm Paused” in the drop-down menu in the multibed screen to pause
all alarms of current monitor for a period of time, which can be set on the monitor.
For the telemetry, you can select “Enter Alarm Paused State” or “Alarm Paused” to pause all
alarms of current telemetry for 2 minutes.
After alarm pause time ends, the system will automatically release the alarm pause. You can
also release the alarm pause by selecting “Exit Alarm Paused State” in the ViewBed screen or
selecting “Alarm Paused” in the specific patient window again.
BeneVision CMS Operator‟s Manual
8-7
You can enable or disable the remote alarm control function on the CentralStation or
WorkStation. When remote alarm control is disabled, “Enter Alarm Paused State” in the
ViewBed screen and “Alarm Pause” in the specific patient window are not available. Refer to
Section 12.2.8 Other to see how to enable or disable the remote alarm control function.
8.6 Resetting Alarms
For telemetry or monitors supporting bidirectional control of alarm reset, you can reset the
alarms through the following ways:
 In the CentralStation/WorkStation ViewBed screens, select “Alarm Reset” from the
“Function” drop-down menu.
 In the Multibed screen, you can right click when the cursor is in the window where the
patient needs the setting of Alarm Reset, or select the option “Alarm Reset” in its dropdown menu.
When “Alarm Reset” is selected, the alarm sounds will be silenced. If a new alarm occurs,
the device will automatically sound.
As for the monitor‟s alarm behaviors after resetting alarm, please refer to the monitor‟s
operator‟s manual. As for the telemetry‟s alarm behaviors after resetting alarm, please refer to
the telemetry operator‟s manual.
You can enable or disable the remote alarm control function on the CentralStation or
WorkStation. When remote alarm control is disabled, the “Alarm Reset” control is not
available in the drop-down menu of the ViewBed and the Multibed screens. Refer to 12.2.8
Other to see how to enable or disable the remote alarm control function.
8-8
BeneVision CMS Operator‟s Manual
9 Review
9.1 Online Review
Online review is used to review the dynamic short trends, C.O. measurements, waveforms,
trends, events, 12 lead analysis and ST segment of a patient that is currently monitored by the
CMS.
NOTE

When Passport 2, Spectrum, Spectrum OR, or V12/21 monitors are connected to
the CentralStation, the following reviews are not available at the corresponding
beds of the CMS.

C.O. review

12-lead review

ST review
9.1.1 Dynamic Short Trend
Selecting “Show Dynamic Trends” from the “View” drop-down menu in the ViewBed screen
will show graphic short trends for the parameter. The colors and order are subject to their
respective parameter modules.
××××
100
××××
××
××××
××
××××
××
0
××
98
××
××
200
××
××
80
××
60
120/80
0
100
××
0
-4h
-2h
0
Figure 9-1 Dynamic Short Trend
The dynamic short trends will automatically update every minute, and the total display time
is 4 hours. Below the bottommost short trend window is a time scale, with scales in -4, -2,
and 0 hour with each vertical line representing an interval of 1 hour.
Click in a parameter‟s dynamic short trend window, and the parameter‟s graph will be
selected. Clicking again will enter the dynamic short trend setup window. The default
BeneVision CMS Operator‟s Manual
9-1
selected parameter is the currently displayed parameter. You can select other parameters in
the window to view the corresponding dynamic short trend graph.
Additionally, you can view more parameters‟ short trends by dragging the vertical scroll bar.
9.1.2 Trend Review
9.1.2.1 Overview
Clicking the “Trend Review” tab will enter a tab sheet, through which you can store and
review up to 240 hours of trend data.
Trend changes can be observed in a graphic or tabular format. You can switch between the
tabular and graphic format by simply clicking their respective buttons.
In the tabular format, parameters from integrated devices are indicated with “+” mark before
the parameter name. In the graphic format, in addition to the “+” mark before the parameter
name, the relevant parameter information of the integrated devices is shown in white.
9.1.2.2 Operation
In this tab sheet, you can:
 Set resolution or zoom
 View parameter values at a certain time
 Select trend group
 Refresh data
 Print
 Save as
For details about print and save as, refer to 11 Record, Print and Save As.
Setting Resolution or Zoom
In the tabular trends, you can set a time interval as the resolution to display the tabular trends.
 When the resolution is set to “1 s”, “5 s”, “1 min”, “5 min”, “15 min”, “30 min”, “1 h” or
“2 h”, the tabular trends will display the measured parameter values for the selected time
period.
 When the resolution is set to “NIBP” or “TEMP”, up to 240 hours of measured values and
other parameter values, which NIBP or TEMP measurement time corresponds to, can be
displayed.
9-2
BeneVision CMS Operator‟s Manual
 When the resolution is set to “Manually Saved”, all the manually input data (such as
glucose) can be displayed.
NOTE

The resolution “TEMP” and “Manually Saved” are available only when
Accutorr 7 monitor is connected.
In the graphic trends, you can set the desired resolution for reviewing graphic trends.
Resolution options include 15 min, 30 min, 1 hour, 2 hours, 4 hours, 8 hours, 12 hours, 24
hours and 48 hours.
Viewing Parameter Values at a Certain Time
By clicking a point in the graphic trends, you can place the cursor at that position and view
the corresponding parameter values of the cursor time. In the tabular trends, the cursor time is
the same as it is in graphic trends. Conversely, if you select a row in the tabular, the cursor in
the graphic trends will be positioned at the time corresponding to that row.
You can further position the time at which the cursor is located by clicking these buttons:
Buttons Graphic
Clicking this button will move to the previous graphic page.
Clicking this button will move the graph to the left by a time range of one resolution.
Clicking this button will move the graph to the right by a time range of one
resolution.
Clicking this button will move to the next graphic page.
Buttons Tabular
Clicking this button will move to the next tabular page.
Clicking this button will move the cursor down one line.
Clicking this button will move the cursor up one line.
Clicking this button will move to the previous tabular page.
Selecting Trend Group
Click the “Trend Group” drop-down list to select the desired trend group to review. For
details about setting trend groups, refer to 12.2.4 Trend Group.
NOTE

Selecting different trend group views in the “Trend Review” screen shows
different trend parameters.
BeneVision CMS Operator‟s Manual
9-3
Refreshing Data
Trend data will not update automatically. Therefore, if you want to view current trend data,
you have to manually refresh the screen. Clicking the “Refresh” button will open a dialog
box, through which you can input a start time and then select “OK” to reload data. After
refreshing, the select status and order of parameters remain unchanged.
9.1.3 Full Disclosure
The CentralStation stores 240 hours of waveform data for each patient.
9.1.3.1 Overview
In the “Full Disclosure” window, you can review compressed or full size waveforms as
required.
9.1.3.2 Compressed Waveform View
Compressed Waveform Screen
Click the “Full Disclosure” tab to open the following window, through which you can review
the patient‟s latest 240 hours of waveform data. In the single screen mode, up to 10 lines of
compressed waveforms are displayed. In the dual- or multi- screen mode, up to 32 lines of
compressed waveforms are displayed.
××
××
××
××××
1
1. Time scale
2
4. Cursor time area
5
4
3
2. Compressed waveform area
6
3. Full size waveform area
5. Cursor
6. Time bar
Figure 9-2 Compressed Waveform View
 Time Scale
Displays the time to which the waveform group in the compressed waveform area
corresponds.
9-4
BeneVision CMS Operator‟s Manual
 Compressed Waveform Area
Displays compressed waveforms. If some waveform signals are not detected within a specific
time period, square waves are displayed.
 Full Size Waveform Area
Displays the full size of the corresponding compressed waveform where the cursor is located,
or displays the patient‟s parameter information.
 Cursor Time Area
Displays the time where the cursor is located.
 Cursor
By moving the cursor, you can select 12 seconds of compressed waveforms. The waveform
data contains 6 seconds before the cursor time and 6 seconds after the cursor time.
 Time Bar
Same functions as in the full size view of full disclosure. Refer to 9.1.3.3 Full Size Waveform
View.
Compressed Waveform Operation
In the compressed view window, you can:
 Select waveforms to be saved
 Select waveforms
 Mark arrhythmia
 View arrhythmia statistics
 Refresh
 Show/hide parameter
 Zoom
 ICP waveform scale
 Print
 Save as
For details about Print and Save as, refer to chapter 11 Record, Print and Save As.
BeneVision CMS Operator‟s Manual
9-5
 Selecting waveforms to be saved
Click the “Wave Save” button to select the desired waveforms to be saved for each patient:
1.
Select a patient from “Patient Info” list.
2.
Select the waveforms to be saved for this patient from the “Waveform” list.
3.
Repeat Step 1 and Step 2 to select waveforms to be saved for other patients.
4.
Select “OK” and the system will save all the selected waveforms.
The CentralStation can save up to 240 hours of waveform data for each patient. If you do not
select waveforms for a patient, no waveforms or parameter values can be reviewed from the
“Full Disclosure” window.
For details about automatic waveform storage, refer to 5.1.3 Auto Waveform Storage.
 Selecting waveforms
Click the “Wave Select” button to display the menu of waveforms. Select the checkbox
beside the desired wave (at most four waves) and the compressed waveform area will display
the selected waves.
To change the order of the waveform, click the waveform name, then select “Move First”,
“Move Up”, “Move Down” or “Move Last”.
Click the “Save as Default” button to save the current configuration as the user‟s default
configuration; click “Load Configuration” to load the user‟s default configuration for the
current patient.
NOTE

The new admitted patient is loaded with the default waveforms.
 Marking arrhythmia
The arrhythmia alarm waveforms can be marked with color in the compressed waveform
area. From the “Arrh Mark” drop-down list, you can select the types of arrhythmia to be
marked.
The marked waveforms start from the point 16 seconds before the arrhythmia alarm, and end
when the alarm condition disappears.
To set desired color for each type of arrhythmia, refer to 12.2.1 Setting Color.
9-6
BeneVision CMS Operator‟s Manual
NOTE

If multiple arrhythmia alarms occur at the same time, only the high priority
alarm(s) will be marked; if the arrhythmia alarms are of the same level, the
alarm of highest priority will be marked.
 Viewing arrhythmia statistics
Click the “Arrh Statistics” button to view the HR value and the number of each arrhythmia
type during a certain time range. You can set the time range as 24 hours, 12 hours, or 8 hours.
For details about Print, refer to chapter 11 Record, Print and Save As.
 Showing/hiding parameter

Click the “Numeric Data” button to display the patient‟s parameter information in
the full size waveform area.

Click the “Hide Numerics” button to display the full size of the cursor-located
compressed wave in the full size waveform area.
 Zoom
Set the time span of each line in the compressed waveform window. The options are 15s, 30s,
45s, 1min and 2min. The longer the time span of each line gets, the more lines of compressed
waveform display on the screen. In single-screen mode, up to 10 lines of waveforms can be
displayed; in dual- or multi- screen mode, up to 32 lines of waveforms can be displayed.
 ICP wavefrom scale
When ICP is displayed in the compressed waveform area, you can right click the mouse to
adjust ICP waveform amplitude. Each time you right click the mouse,, the scale is adjusted in
the preset order. There are four levels of the scale: 0-15 mmHg, 0-20 mmHg, 0-30 mmHg and
0-40 mmHg. After the change, the scale level displays above the ICP waveform.
BeneVision CMS Operator‟s Manual
9-7
9.1.3.3 Full Size Waveform View
Full Size Waveform Screen
Click the “Full Disclosure” tab. Click the “Full Size” button to open the following window,
through which you can review the patient‟s latest 240 hours of waveform data.
7
5
××
××
2
××
××××
××××
×× 60 ××
×× 98 ××
××××
×× 60 ××
×× 37.7 ××
4
3
×× 37.2 ××
1
××
××××
6
1. Time bar
4. Waveform time display area
7. Caliper measurement area
2. Waveform area
5. Current cursor
8. Button area
3. Parameter area
6. Caliper
Figure 9-3 Full Size Waveform View
 Time Bar
The time bar adopts different colors to identify the alarm status of different time periods:

White: indicates that there are no waveforms or values.

Grey: indicates that there are waveforms and all monitored parameters are within
range and no alarms are occurring.

Red: indicates that some parameters have high priority alarms but there are still
waveforms.

Yellow: indicates that some parameters have medium priority alarms but there are
still waveforms.

Cyan: indicates that some parameters have low priority alarms but there are still
waveforms.
Within the time bar, there is a black line indicating the time to which the current cursor
corresponds. While moving the cursor along the time bar, the time corresponding to the
cursor location will appear above the time bar. By clicking the mouse, you can confirm the
time to which the current cursor corresponds. In addition, you can further adjust the black
line by using these buttons and the waveform will also move accordingly.


9-8
: Clicking it will move the black line to the leftmost, i.e. the review start time.
: Clicking it will move the black line left, so that the waveforms in the
waveform area move left at the length of one screen.
BeneVision CMS Operator‟s Manual
8

: Clicking it will move the black line left in short increments.

: Clicking it will move the black line right in short increments.


: Clicking it will move the black line right, so that the waveforms in the
waveform area move right at the length of one screen.
: Clicking it will move the black line to the rightmost, i.e. the review end time.
 Waveform Area
This area displays the waveform strips over a specific period. Click in the waveform area,
and the grey triangles on the top of and at the bottom of the waveform area will appear
indicating the current time corresponding to the cursor location.
Caliper Measurement
Left click the mouse at a place in the waveform area and then hold it down while dragging
the cursor until your desired location is reached. During dragging, a caliper with two arms
and a middle measurement line, marking the real time measurement, will appear on the
waveforms. You can drag the cursor in vertical or horizontal direction:

In horizontal direction, the PR, QRS, RR, QTC, and QTC can be measured. The
horizontal caliper is shown in Figure 9-4 Horizontal Caliper.

In vertical direction, the ST can be measured. The vertical caliper is shown in Figure 9-5
Vertical Caliper.
If a touchscreen is configured, select a place in the waveform by a harder fingertip touch on
the screen, and then drag your finger on the screen surface without losing the contact until the
desired location is reached. A caliper is then formd. If you need to adjust the caliper, slightly
touch the left or right arm, then the touchscreen controls
4
and
will appear.
5
××
1
2
3
Figure 9-4 Horizontal Caliper
BeneVision CMS Operator‟s Manual
9-9
2
5
6
XX
7
Figure 9-5 Vertical Caliper
1. Left arm
4. Current cursor
7. Lower arm
2. Measurement line
5.Real-time measurement
3. Right arm
6. Upper arm
When a caliper is formed, you can adjust the caliper by the following operations to measure
the time difference between any two points:

When the cursor is positioned at caliper arm, and the cursor turns to
can horizontally move the arm.

When the cursor is positioned at measurement line, and the cursor turns to
, you
,
you can vertically move the measurement line.

When the cursor is positioned between the two arms, and the cursor turns to
,
you can move the whole caliper.
In the waveform area, right click the mouse, and select “PR”, “QRS”, “RR”, “QT” or “ST” in
the pop-up menu. The corresponding measurement will be shown above the first ECG
waveform. In the caliper measurement area, the above-mentioned value can be acquired also.
Refer to 9.1.3.3 Full Size Waveform View for additional information on the caliper
measurement area.
In the pop-up menu, select “Change Caliper” to switch between vertical caliper and
horizontal caliper.
9-10
BeneVision CMS Operator‟s Manual
NOTE

The current caliper measurements can be manually saved as an event.

The full disclosure does not include caliper measurements.

When dragging the cursor to form a caliper, you can move the cursor vertically
to move the measurement line in a horizontal caliper; or move the cursor
horizontally to move the measurement line in a vertical capliper.
ECG Waveform Gain
You can set the ECG waveform gain in the waveform area in one of the following ways:

When the cursor is positioned at any ECG waveform, the buttons
display at the left end of the waveform. Click
click

and
will
button can increase the gain, and
button can decrease the gain.
Right click mouse, and select “Zoom in ECG Gain” or “Zoom out ECG Gain” in
the pop-up menu.
Sweep Speed
You can set the sweep speed in one of the following ways:

In the waveform area, right click the mouse and select either “Zoom in Sweep
Speed” or “Zoom out Sweep Speed” to adjust the speed.

In the button area, click “Sweep Speed” to set the waveform sweep speed. Refer to
9.1.3.3 Full Size Waveform View for additional information on selecting sweep
speed.
 Caliper Measurement Area
The caliper measurement area is hidden by default. If the check box before “Caliper” is
selected at the right bottom corner of the screen, this area will be shown; otherwise it will be
hidden.
There are six measurement buttons and one “Clear” button. You can:

Double click “PR”, “QRS”, “RR”, “QT” and “ST” buttons to obtain their values.
The QTC value is calculated after RR and QT value have been acquired.

Clear all the values by clicking the “Clear” button.
 Parameter Area
By default, the parameter area is hidden. Clicking the “Numeric Data” button will show the
parameter area. If the parameter area is displayed, clicking the “Hide Numerics” button will
BeneVision CMS Operator‟s Manual
9-11
hide the parameter area.
Parameter area shows all current parameter values.

Parameters having high-level alarms are highlighted in red and “***” is shown in
front of the parameter values.

Parameters having medium level alarms are highlighted in yellow and “**” is
shown in front of the parameter values.

Parameters having low level alarms are highlighted in cyan and “*” is shown in
front of the parameter values.

Parameters that have a message are shown with black as the background color, but
no indication of “*” before parameter values.

Parameters from integrated devices are shown in white and indicated with “+”
before the parameter name.
 Waveform Time Display Area
In this area, waveform start time and end time are respectively shown at leftmost and
rightmost; the current cursor time is shown in the middle. By clicking the “Refresh” button,
you can update the end time to current system time and the start time changes accordingly.
 Button Area
Refer to 9.1.3.3 Full Size Waveform View - Full Size Waveform Operation for additional
information about button function.
Full Size Waveform Operation
In the full size waveform screen, you can:
 Select waveforms to be saved
 Select waveforms
 Select sweep speed
 Save event
 Auto play
 Record
 Print
 Save as
 Export to Electronic Medical Record (EMR) system
For details about record, print and save as, refer to chapter 11 Record, Print and Save As.
9-12
BeneVision CMS Operator‟s Manual
 Selecting waveforms to be saved
By clicking the “Wave Save” button, you can select waveforms to be saved for each patient
as desired by following this procedure:
1.
Select a patient from “Patient Info” list.
2.
Select waveforms to be saved for this patient from the “Waveform” list.
3.
Repeat step 1 and step 2 to select waveforms to be saved for other patients.
4.
Select “OK” and the system will save all the selected waveforms.
The CentralStation can save up to 240 hours of waveform data for each patient. If you do not
select waveforms for a patient, waveform and parameter values cannot be reviewed from the
“Full Disclosure” window.
For details about automatic waveform storage, refer to 5.1.3 Auto Waveform Storage.
 Selecting waveforms
Click the “Wave Select” button, and a list of available waveforms will be shown. By default,
all waveforms are selected. You can deselect a waveform by selecting its check box. You can
also drag a waveform name to change its display order.
 Selecting sweep speed
By clicking the “Sweep Speed” button, you can set the width of waveforms displayed in the
waveform area. Available options are 6.25 mm/s, 12.5 mm/s, 25 mm/s and 50 mm/s.
Changing sweep speed will affect the time length of the waveform area. At the 1280×1024
resolution, the sweep speed and time length correlate as follows:
Sweep Speed
Time length (approximate)
6.25 mm/s
12.5 mm/s
25 mm/s
50 mm/s
52.0s
26.0s
13.0s
6.5s
 Saving event
Clicking the “Save Event” button will enter a dialog box. Select the waveforms that can be
saved and input an event description. Select “OK” to save the currently displayed waveform
strips. The saved event can be viewed in the “Event Review” screen.
 Auto play
By clicking “Auto Play” and then selecting the
review waveforms in the auto mode.
BeneVision CMS Operator‟s Manual
,
,
or
buttons, you can
9-13
 Export to EMR
By clicking the “Export to EMR” button, you can export 20 seconds of waveform data after
the start time of the current waveform to other systems.
NOTE

The Export to EMR function is available only when the eGateway is configured.

The Export to EMR function is available when “Export Waveform Data” is
enabled in “Admin Setup” – “Other” – “Communication Settings” – “Gateway
Communication Settings”.
9.1.4 C.O. Review
9.1.4.1 Overview
Clicking the “C.O. Review” tab will enter a tab sheet, through which you can view up to 720
C.O. measurement curves and parameter values of a patient.
××
××
××
××
××
××
××
××××
××××
2
××××
1
××××
××××
×××
×××
Figure 9-6 C.O. Review
1. Measurement list
2. Waveform area
3. Button area
Below the C.O. review windows are the average C.O. and C.I. If you switch to the “Hemo
Calcs” tab sheet from a C.O. review window, the system will take the average C.O. and C.I.
corresponding to that C.O. review window as the inputs of the hemodynamic calculation.
9.1.4.2 Operation
In the “C.O. Review” window, you can:
 Select measurements
 Delete a set of measurements
 Print
 Record
9-14
BeneVision CMS Operator‟s Manual
3
 Save as
For details about record, print and save as, refer to 11 Record, Print and Save As.
Selecting measurements
The time corresponding to each measurement is listed in the “Measure results list”, from
which you can select up to 6 measurements. To the right of the “Measure results list”, there
are six (6) C.O. review windows, displaying the C.O. curves and parameter values measured
at six (6) different times.
Click in a C.O. review window. The border of the window will highlight in blue when it is
selected.
Deleting a set of measurements
1.
Select the time or C.O. review window corresponding to the measurement you want to
delete.
2.
Click the “Delete” button, and a dialog box to confirm the deletion will pop up.
3.
Select “Yes” to delete the measurement.
9.1.5 Event Review
9.1.5.1 Overview
Clicking the “Event Review” tab will enter the following tab sheet, through which you can
view all event parameters and waveforms of a patient.
3
2
1
1 Event list
2 Event parameter area
3 Event waveform area
Figure 9-7 Event Review Tab Sheet
1.
Event list: displays event status (locked or not), time, message, priority and description.
2.
Event parameter area: displays all parameter values for each event time. The integrated
device parameters are indicated with a “+” before the parameter name, and the relevant
BeneVision CMS Operator‟s Manual
9-15
text is shown in white. The CentralStation prompts if an alarm occurs for a specific
parameter and indicates the alarm priority by using different background colors.
3.

Black: no alarm generated

Red: high priority alarm generated

Yellow: medium priority alarm generated

Cyan: low priority alarm generated
Event waveform area: displays relevant parameters‟ waveforms within ±16 seconds
around the event time. Please refer to 9.1.3.3 Full Size Waveform View - Full Size
Waveform Screen - Waveform Area for how to use calipers, how to adjust ECG
waveform gain, and how to adjust sweep speed in waveform area.
Select an event from the event list and you will view its corresponding parameter values and
waveforms in the event parameter area and event waveform area.
NOTE

For the integrated device events, there are no corresponding waveforms in the
event waveform area.

If the alarm is paused, the events during the pausing period are not recorded.
9.1.5.2 Operation
In the “Event Review” window, you can:
 Select event type and alarm priority
 Sequence the event list
 Make selection
 Lock and unlock
 Delete
 Sweep speed
 Caliper measurement
 Print
 Record
 Save as
 Export to EMR
For details about sweep speed and caliper measurement, refer to 9.1.3.3 Full Size Waveform
View.
For details about record, print and save as, refer to chapter 11 Record, Print and Save As.
9-16
BeneVision CMS Operator‟s Manual
Selecting Event Type and Alarm Priority
Above the event list, there are two drop-down list boxes: “Filter by Event” and “Filter by
Priority”. By clicking the down arrow buttons next to them, you can select event type and
level. The selected events will be listed in the event list.
Options for event type are “All”, “ECG”, “SpO2”, “RESP”, “NIBP”, “IBP”, “C.O.”, “TEMP”,
“CO2”, “GAS”, “ICG”, “BIS”, “RM”, “CCO”, “SvO2”, “ScvO2”, “Arrh”, “ST Analysis”,
“Saved Event” ,“Event”(only for telemetry), “Anesthesia”, “Ventilator”, “Unknown Phys.
Alarm”, “Manual Event”, and options for alarm priority include “All”, “High”, “Med”,
“Low” or “Message”. By default, “All” for alarm type and “All” for alarm priority are
selected.
Sorting the Event List
You can sort all events ascendingly or descendingly by clicking the heading of any column:
 Time: Clicking it will sort all alarms ascendingly or descendingly by time.
 Message: Clicking it will sort all alarms ascendingly or descendingly by parameter.
 Description: Clicking it will sort all alarms ascendingly or descendingly by description.
 Priority: Clicking it will sort all alarms ascendingly or descendingly by level.
At the same time, one of the following symbols will appear to the left of the heading:

for ascending sequence, and

for descending sequence.
By default, all events are sorted in descending order by time.
Making Selection
You can select single, multiple or all events in event list:
 Select one event: Click one event you wish to select.
 Select multiple events: You can select more than one event with the Ctrl or Shift keys.

Select the first event and then press and hold the Ctrl key. While holding down the
Ctrl key, select each of the other events you wish to select. This will select
multiple events that are not grouped together.

Select the first event and then press and hold the Shift key. While holding the key
down, click the last event. This will select all the events in-between the first and
last event.
 Select all events: Click any event in the list, and then press the Ctrl + A keys on the
keyboard together and then all the events in the event list will be selected.
BeneVision CMS Operator‟s Manual
9-17
Locking and Unlocking Events (CentralStation Only)
Select an event from the event list and then click the “Lock” button. The icon will appear
to its left when the event is locked. The locked event cannot be deleted automatically, but can
be deleted manually.
NOTE

If events are all locked, the CentralStation will automatically delete the oldest
locked event with each addition of a new event when system storage reaches
capacity.
When a locked event is selected, the button “Lock” will change to “Unlock”. You can click
the “Unlock” button to unlock the locked event.
Deleting Event (CentralStation Only)
1.
On the CentralStation, select the event you wish to delete from the event list.
2.
Click the “Delete” button.
3.
Select “OK” from the pop-up dialog box. This event will be deleted.
Exporting to EMR
Select one event from event list, and then click the “Export to EMR” button. The event
related data can be exported to other systems.
NOTE
9-18

The Export to EMR function is available only when the eGateway is configured.

The Export to EMR function is available when “Export Waveform Data” is
enabled in “Admin Setup” – “Other” – Communication Settings” – “Gateway
Communication Settings”.
BeneVision CMS Operator‟s Manual
9.1.6 12-Lead Review
If the bedside monitor supports the 12-lead analysis function, you can click the “12-lead
Review” tab to review the 12-lead analysis result obtained from the bedside monitor.
Refer to 9.1.3.3 Full Size Waveform View - Full Size Waveform Screen - Waveform Area
for how to use calipers, how to adjust ECG waveform gain, and how to adjust sweep speed in
waveform area.
In the “12-lead Review” window, you can:
 View 12 analysis waveforms
 Delete
 Sweep speed
 Print
 Record
 Save as
 Modify patient information
For details about sweep speed, refer to 9.1.3.3 Full Size Waveform View -Full Size
Waveform Screen.
For details about record, print and save as, refer to chapter 11 Record, Print and Save As.
NOTE

In the “12-lead Review” tab sheet, there is no caliper measurement area. “PR”,
“QRS”, “RR” and “QT” cannot be measured.
Viewing 12-Lead Analysis Waveforms
12-Lead analysis waveforms will be displayed on the right side by selecting an analysis result
and clicking the “Waveforms” button. You can move the vertical scroll bar to view the
waveforms. To view the analysis results, click the “List” button.
Deleting a Result
You can delete an analysis result by selecting it, and then clicking the “Delete” button. For
details about record, print and save as, refer to chapter 11 Record, Print and Save As.
Modifying Patient Information
If the Glasgow algorithm is used for 12-lead ECG analysis in the bedside monitor, you can
modify the patient information by clicking the “Patient Info” button in “12-Lead Review” tab
sheet.
BeneVision CMS Operator‟s Manual
9-19
The editable patient information includes patient ID, last/first name, technician and
physician. The modified information will be updated in the 12-lead analysis report, strip, and
saved file. The change of patient ID, first name or last name will also be updated in patient
management.
9.1.7 ST Review
9.1.7.1 Overview
Click the “ST Review” tab to open the ST review window as shown in Figure 9-5. In this
window, you can view real-time ST segments and review historical ST segments. You can
also record and print out ST segments.
3
2
1
1. Setting control area
Time
scale
Reference Historical Reference ST
segment mark
cursor
cursor
2. Trend parameter area
ST segment
mark bar
3. ST segment area
Figure 9-8 ST Review
1.
Setting control area: sets up ST segments and trend parameters.
2.
Trend parameter area: displays trended parameters, reference cursor, historical cursor
and ST segment mark.
3. ST segment area: displays real-time or historical ST segments and reference ST segment.
WARNING

9-20
The ST algorithm has been tested for accuracy of the ST segment data. The
significance of the ST segment changes need to be determined by a clinician.
BeneVision CMS Operator‟s Manual
9.1.7.2 Operation
In the ST Review window, you can:
 View ST segment
 Set reference ST segment
 Select reference ST segment
 Delete reference ST segment
 Set waveform speed
 Set trend parameter
 Print
 Record
For details about record and print, refer to Chapter 11 Record, Print and Save As.
Viewing ST Segment
In the setting control area, you can select “Real-time” to view real-time ST segments,
“Historical” to view historical ST segments by using the “View Hist.” buttons. You can also
view historical ST segments by clicking any position in the parameter trend area.
Setting Reference ST Segment
When viewing real-time ST segments, click “Set as Ref.” to set the real-time ST segment to
reference ST segment. When viewing historical ST segments, click “Set as Ref.” to set the ST
segment located at the historical cursor to the reference ST segment.
Selecting Reference ST Segment
You can click the “Change Ref.” button to set the reference ST segment located at the
reference cursor to the current reference ST segment.
Deleting Reference ST Segment
You can click the “Delete Ref.” button to delete the reference ST segment located at the
reference cursor.
Setting Waveform Speed
You can click the “Sweep Speed” drop-down list to set different waveform speeds. The time
scale in the ST segment area is related to the waveform speed set. The greater the waveform
speed, the smaller the time scale.
BeneVision CMS Operator‟s Manual
9-21
Setting Trend Parameter
You can click the “Trend Parameter” drop-down list to select two different trend parameters
and “Zoom” drop-down list to set different time lengths.
The parameter trend data is not refreshed automatically. You can click the “Refresh” button
and set start time in the pop-up window, and then click “OK” to read the data again.
NOTE

There is no data displayed in the trend parameter area when viewing real-time
ST segments.
9.2 Discharged Patients
The CentralStation is capable of searching and reviewing the history data of up to 20,000
patients. By clicking the “Discharged Pat.” button, you can enter the tab sheets as follows:
 All patients
 Patient Mgmt.
 Full Disclosure
 Trend Review
 Event Review
 12-lead Review
 ST Review
 C.O. Review
NOTE

9-22
The patient management, full disclosure, trend review, event review, 12-lead
review, ST review and C.O. review for discharged patients are essentially the
same as those for online patients. For details, refer to 9.1 Online Review.
BeneVision CMS Operator‟s Manual
9.2.1 All Patients
9.2.1.1 Overview
In the “All patients” tab sheet, you can view discharged patients‟ data from all
CentralStations on the network. Brief information of discharged patients on the selected
CentralStation is shown in the patient list, with one line for each discharged patient.
NOTE

The discharged patients on a CentralStation can be viewed only when the
CentralStation is connected to the monitoring network. Please refer to 12.3
Communication Settings for additional information.
9.2.1.2 Operation
In the “All patients” tab sheet, you can:
 Sort discharged patients
 Search discharged patients
 Delete discharged patients
 Refresh
Sorting Discharged Patients
You can sort all discharged patients ascendingly or descendingly by clicking the heading of
any column. At the same time, one of the following symbols will appear to the left of the
heading:

for ascending sequence, and

for descending sequence.
By default, all discharged patients are sorted ascendingly by name.
Searching Discharged Patients
1.
Click the button at the left of the “All patients” tab sheet, or select “Show Search”
button, and the “All patients” tab sheet will show an area on the left for inputting search
conditions.
2.
Input search conditions, e.g. “Name” and “Patient ID”. You can click “More Options” to
input more search conditions.
3.
Click the “Search” button. The system will search and display the discharged patients
that meet the search conditions.
BeneVision CMS Operator‟s Manual
9-23
Deleting Discharged Patients
1.
In the “Delete” column, select the check box corresponding to the patient that you want
to delete.
2.
Click the “Delete” button.
3.
Select “Yes” from the pop-up dialog box.
Refreshing Data
Clicking the “Refresh” button will update the discharged patient list.
NOTE
9-24

Only after selecting a discharged patient from the “All patients” tab sheet, can
you switch to other tab sheets for review.

If a patient is allowed to be viewed by remote CMS during monitoring, the
patient‟s physiological data can be viewed in the “Discharged Pat.” window of
other CentralStations after the patient is discharged.
BeneVision CMS Operator‟s Manual
10 Calculation
10.1 Drug Calculation
Clicking the “Drug Calcs” tab will enter the tab sheet.
The “Calculated Results List” shows the time corresponding to a maximum of 75
calculations. The drug parameter area is for you to enter parameter values and to display
calculations. The titration table is to show titrated results.
The button area contains the following buttons:
 Calc.
 Save Results
 Delete
 Record
 Print
 Save As
For details about Record, Print and Save as, refer to chapter 11 Record, Print and Save As.
BeneVision CMS Operator‟s Manual
10-1
Calculate
From the “Name” drop-down list below, you can select one of the choices listed to calculate
its amount, liquid volume, concentration, etc.
 Drug A
 Drug B
 Drug C
 Drug D
 Drug E
 AMINOPHYLLINE
 DOBUTAMINE
 DOPAMINE
 EPINEPHRINE
 HEPARIN
 ISUPREL
 LIDOCAINE
 NIPRIDE
 NITROGLYCERIN
 PITOCIN
NOTE

Drug A through Drug E are user-defined drugs.
Procedure
To make a calculation:
1.
Confirm whether the patient type and weight entered are correct.
2.
Select a drug to be calculated.
3. The system will automatically give a set of values. Do not use these calculations. Instead,
input correct parameter values under the direction of a physician.
10-2
4.
Select “Reference”, “Dose Interval” and “Dose Type” for titration table.
5.
Click the “Calc.” button. The calculations will be displayed in the drug parameter area
and titration table.
BeneVision CMS Operator‟s Manual
WARNING

Be sure to input correct parameter values. The user must verify the correctness of
the calculations displayed on the screen before using them.

The calculations in the titration table are subject to the drug calculations,
therefore, the correctness of the drug calculations must be ensured. In addition,
the reference, dose interval and dose type should be confirmed.

We assume no responsibility for results arising from incorrect inputs and
operations.
Save Results
The CentralStation is capable of saving 75 calculations for each patient. To save calculations,
you can click the “Save Results” button after the calculation is finished.
If the drug you select is a user-defined drug, the system will open the “Enter drug name”
dialog box. Input a drug name and click “OK”. The system will remember this name and save
it into the Name drop-down list for later use.
All the saved calculations and their respective calculation times are displayed in the
“Calculated Results List”. From this list, you can select a specific calculation to view in the
drug parameter area. At this time, all parameters in the drug parameter area are unchangeable
but the reference, dose interval and dose type in the titration table can be changed by
selecting the “New Calc.” button. Click the “New Calc.” button to input new parameter
values and create a new calculation.
Delete
To delete unnecessary or incorrect calculations:
1.
Select the time corresponding to the calculation you want to delete from the “Calculated
Results List”.
2.
Click the “Delete” button below the “Calculated Results List”.
3.
Select “Yes” in the message box. The calculation will be deleted.
BeneVision CMS Operator‟s Manual
10-3
10.2 Hemodynamics Calculation
Clicking the “Hemo Calcs” tab will enter the tab sheet.
The “Calculated Results List” shows the time corresponding to a maximum of 100
calculations. The “Input Item” area allows you to enter parameter values and the “Calculated
Results” area is to display calculations.
In this tab sheet, you can:
 Calculate
 Save results
 Delete
 Print
 Record
 Save as
For details about Record, Print and Save as, refer to chapter 11 Record, Print and Save As.
Calculate
To calculate a value:
1.
Input parameter values needed into the “Input Item” area.
2.
Click the “Calc.” button. The calculations of other parameters will be displayed in the
“Calculated Results” area. Values which are beyond the normal range will be displayed
on a yellow background.
WARNING

10-4
Be sure to input correct parameter values. The user must verify the correctness of
the calculations displayed on the screen before using them. We assume no
responsibility for results arising from incorrect inputs and operations.
BeneVision CMS Operator‟s Manual
Save Results
The CentralStation is capable of saving 100 calculations for each patient. To save
calculations, click the “Save Results” button after the calculation is finished.
NOTE

If you continue to perform the “Save Results” operation when the number of
calculations exceeds 100, the system will delete the earliest calculation and its
corresponding time from the “Calculated Results List” before saving the new one.
Delete
To delete unnecessary or incorrect calculations:
1.
Select the time corresponding to the calculation you want to delete from the “Calculated
Results List”.
2.
Click the “Delete” button below the “Calculated Results List”.
3.
Select “Yes” in the message box. The calculation will be deleted.
10.3 Oxygenation Calculation
Clicking the “Oxygenation Calc.” tab will enter the tab sheet.
The “Calculated Results List” shows the time corresponding to a maximum of 100
calculations. The “Input Item” area allows you to enter parameter values, and the “Calculated
Results” area is to display calculations.
In this tab sheet, you can:
 Calculate
 Save results
 Delete
 Print
 Record
 Save as
For details about Record, Print and Save as, refer to chapter 11 Record, Print and Save As.
BeneVision CMS Operator‟s Manual
10-5
Calculate
To calculate a value:
1.
Input parameter values needed into the “Input Item” area.
2.
Pressure unit, Hb unit and Oxygen content unit can be changed by scrolling the dropdown lists at the right side of “Press Unit” or “OxyCont Unit”. Parameter values will
automatically change and refresh accordingly.
3.
Click the “Calc.” button. The calculations of other parameters will be displayed in the
“Calculated Results” area. Parameter values which are beyond the normal range will be
displayed on a yellow background.
WARNING

Be sure to input correct parameter values. The user must verify the correctness of
the calculations displayed on the screen before using them. We assume no
responsibility for results arising from incorrect inputs and operations.
Save Results
The CentralStation is capable of saving 100 calculations for each patient. To save
calculations, you can click the “Save Results” button after the calculation is finished.
NOTE

If you continue to perform the “Save Results” operation when the number of
calculations exceeds 100, the system will delete the earliest calculation and its
corresponding time from the “Calculated Results List” before saving the new one.
Delete
To delete unnecessary or incorrect calculations:
10-6
1.
Select the time corresponding to the calculation you want to delete from the “Calculated
Results List”.
2.
Click the “Delete” button below the “Calculated Results List”.
3.
Select “Yes” in the message box. The calculation will be deleted.
BeneVision CMS Operator‟s Manual
10.4 Ventilation Calculation
Clicking the “Ventilation Calc.” tab will enter the tab sheet.
The “Calculated Results List” shows the time corresponding to a maximum of 100
calculations. The “Input Item” area allows you to enter parameter values, and the “Calculated
Results” area is to display calculations.
In this tab sheet, you can:
 Calculate
 Save results
 Delete
 Print
 Record
 Save as
For details about Record, Print and Save as, refer to chapter 11 Record, Print and Save As.
Calculate
To calculate a value:
1.
Input parameter values needed into the “Input Item” area.
2.
Pressure unit can be changed by scrolling the drop-down list at the right side of “Press
Unit”. Pressure values will automatically change and refresh accordingly.
3.
Click the “Calc” button. The calculations of other parameters will be displayed in the
“Calculated Results” area. Parameter values which are beyond the normal range will be
displayed on a yellow background.
WARNING

Be sure to input correct parameter values. The user must verify the correctness of
the calculations displayed on the screen before using them. We assume no
responsibility for results arising from incorrect inputs and operations.
Save Results
The CentralStation is capable of saving 100 calculations for each patient. To save
calculations, you can click the “Save Results” button after the calculation is finished.
BeneVision CMS Operator‟s Manual
10-7
NOTE

If you continue to perform the “Save Results” operation when the number of
calculations exceeds 100, the system will delete the earliest calculation and its
corresponding time from the “Calculated Results List” before saving the new one.
Delete
To delete unnecessary or incorrect calculations:
1.
Select the time corresponding to the calculation you want to delete from the “Calculated
Results List”.
2.
Click the “Delete” button below the “Calculated Results List”.
3.
Select “Yes” in the message box. The calculation will be deleted.
10.5 Renal Calculation
Clicking the “Renal Calc.” tab will enter the tab sheet.
The “Calculated Results List” shows the time corresponding to a maximum of 100
calculations. The “Input Item” area allows you to enter parameter values and the “Calculated
Results” area is to display calculations.
In this tab sheet, you can:
 Calculate
 Save results
 Delete
 Print
 Record
 Save as
For details about Record, Print and Save as, refer to Chapter 11 Record, Print and Save As.
10-8
BeneVision CMS Operator‟s Manual
Calculate
To calculate a value:
1.
Input parameter values needed into the “Input Item” area.
2.
Click the “Calc” button. The calculations of other parameters will be displayed in the
“Calculated Results” area. Parameter values which are beyond the normal range will be
displayed on a yellow background.
WARNING

Be sure to input correct parameter values. The user must verify the correctness of
the calculations displayed on the screen before using them. We assume no
responsibility for results arising from incorrect inputs and operations.
Save Results
The CentralStation is capable of saving 100 calculations for each patient. To save
calculations, you can click the “Save Results” button after the calculation is finished.
NOTE

If you continue to perform the “Save Results” operation when the number of
calculations exceeds 100, the system will delete the earliest calculation and its
corresponding time from the “Calculated Results List” before saving the new one.
Delete
To delete unnecessary or incorrect calculations:
1.
Select the time corresponding to the calculation you want to delete from the “Calculated
Results List”.
2.
Click the “Delete” button below the “Calculated Results List”.
3.
Select “Yes” in the message box. The calculation will be deleted.
BeneVision CMS Operator‟s Manual
10-9
FOR YOUR NOTES
10-10
BeneVision CMS Operator‟s Manual
11 Record, Print and Save As
11.1 Record
As shown Figure 11-1below, the CMS can be equipped with a thermal recorder, which, with a
separate power supply, is connected to the host via the general interface.
The CMS supports the following recorders.

TR6B Recorder

TR6F Recorder
TR6B Recorder
Power indicator
Figure 11-1 Front Panel
Power switch
Equipotential grounding
connector
Fuse
RS232 connector
Power inlet
Figure 11-2 Back Panel
BeneVision CMS Operator‟s Manual
11-1
TR6F Recorder
Indicator
Latch
Figure 11-3 Front Panel
Equipotential
grounding
connector
RS232 connector
Power Switch
Power inlet
Figure 11-4 Front Panel
The indicator has three statuses:
 On: indicates that the recorder can print normally.
 Off: indicates that the recorder is switched off.
 Flashing: indicates that the reorder cannot print normally, e.g. the recorder runs out of
paper.
The top left button of the recorder front panel has no function.
Recording can be divided into manual recording and auto recording. The former requires you
to press the “Record” button before recording. The latter, also called real-time recording,
means that the system automatically initiates a recording when an alarm occurs. The CMS
can print out the following information through the recorder:
11-2
BeneVision CMS Operator‟s Manual
 Patient Information
 Drug Calculations
 Hemodynamics Calculations
 Oxygenation Calculations
 Ventilation Calculations
 Renal Calculations
 Waveforms
 Events
 C.O. Measurements
 12-Lead Review
 ST Review
 ICG Hemodynamic Parameters
 CCO Hemodynamic Parameters
 SvO2/ScvO2 Oxygenation Parameters
 Real-time Waveforms
 Real-time Frozen Waveforms
 Real-time Alarms
BeneVision CMS Operator‟s Manual
11-3
11.1.1 Installing Recorder Paper
WARNING

Be sure to use standard (50mm) thermal recorder paper only; otherwise, the
recorder may print with poor quality, may be unusable, or the recorder printer
head may become damaged.

Be careful to avoid damaging the printer head when installing recorder paper.
Never pull open the paper bail at the upper left corner of the recorder except if
you plan to replace the recorder paper or resolve an issue.
TR6B Recorder Installation
To install recorder paper, follow this procedure.
1.
Open the recorder door, and open the paper bail at the upper left corner of the recorder,
shown in Figure 11-5.
2.
Insert a new roll of recorder paper into the paper compartment, shown in Figure 11-4.
3.
Insert the paper shown in Figure 11-5.
4.
Pull the paper out and adjust it, shown in Figure 11-6.
5.
Push down the paper bail, shown in Figure 11-7.
6.
Close the recorder door, shown in Figure 11-8.
Figure 11-5 Installing Recorder Paper -1 Figure 11-6 Installing Recorder Paper -2
Figure 11-7 Installing Recorder Paper -3 Figure 11-8 Installing Recorder Paper -4
11-4
BeneVision CMS Operator‟s Manual
Figure 11-9 Installing Recorder Paper -5 Figure 11-10 Installing Recorder Paper -6
TR6F Recorder Installation
To install recorder paper, follow this procedure.
1.
Use the latch at the upper right of the recorder door to pull the door open, shown in
Figure 11-11.
2.
Insert a new roll into the compartment with the inner paper side facing up, shown in
Figure 11-12.
3.
Close the door.
4.
Verify that paper is loaded correctly and the paper end is feeding from the top.
Figure 11-11 Installing Recorder Paper-1
BeneVision CMS Operator‟s Manual
Figure 11-12 Installing Recorder Paper-2
11-5
11.1.2 Recorder Operations
Recording Patient Information
1.
Enter the “Patient Mgmt.” tab sheet.
2.
Make sure that the patient information is correct.
3.
Click the “Record” button to print out the patient information.
Recording Drug Calculations
1.
Enter the “Drug Calcs” tab sheet.
2.
Perform drug calculation as per 10.1 Drug Calculation.
3.
Click the “Record” button to print out the drug calculations result.
Recording Hemodynamics Calculations
1.
Enter the “Hemo Calcs” tab sheet.
2.
Perform hemodynamics calculation as per 10.2 Hemodynamics Calculation.
3.
Click the “Record” button to print out the hemodynamics calculations.
Recording Oxygenation Calculations
1.
Enter the “Oxygenation Calc.” tab sheet.
2.
Perform oxygenation calculation as per 10.3 Oxygenation Calculation.
3.
Click the “Record” button to print out the oxygenation calculations.
Recording Ventilation Calculations
1.
Enter the “Ventilation Calc.” tab sheet.
2.
Perform ventilation calculation as per 10.4 Ventilation Calculation.
3.
Click the “Record” button to print out the ventilation calculations.
Recording Renal Calculations
11-6
1.
Enter the “Renal Calc.” tab sheet.
2.
Perform renal calculation per 10.5 Renal Calculation.
3.
Click the “Record” button to print out the renal calculations.
BeneVision CMS Operator‟s Manual
Recording Full Size Waveforms
1.
Enter the “Full Disclosure” tab sheet.
2.
Click the “Full Size” button.
3.
Click the “Record” button.
4.
Select a maximum of two (2) waveforms from the pop-up dialog box.
5.
Select “OK” to print out the selected waveforms.
Recording Events
1.
Enter the “Event Review” tab sheet.
2.
Select an event from the event list per 9.1.5 Event Review.
3.
Click the “Record” button.
4.
From the pop-up dialog box, you can select a maximum of two (2) waveforms.
5.
Select “OK” to print out the selected waveforms.
Recording C.O. Measurements
1.
Enter the “C.O. Review” tab sheet.
2.
Select one C.O. measurement.
3.
Click the “Record” button to print out the selected C.O. measurement.
Recording 12-Lead Analysis Results
1.
Enter the “12-lead Review” tab sheet.
2.
Click the “Record” button.
3.
Select “Time Range” from the pop-up dialog box.
4.
Click “OK” to print out the 12-lead analysis result list.
Recording 12-Lead Analysis Waveform
1.
Enter the “12-lead Review” tab sheet.
2.
Click the “Waveforms” button after selecting an analysis result.
3.
Click the “Record” button to print out the analysis results and 12 analysis waveforms.
BeneVision CMS Operator‟s Manual
11-7
Recording ST Segment Waveform
1.
Enter the “ST Review” tab sheet.
2.
Click the “Record” button.
3.
Select “Sweep Speed” from the pop-up dialog box.
4.
Click “OK” to print out ST segment.
Recording ICG Hemodynamic Parameters
1.
Enter the “ViewBed” tab sheet.
2.
Select and then click the ICG parameter area.
3.
Select the “ICG” tab sheet and click the “Hemodynamic Parameters” button.
4.
Click the “Record” button from the pop-up dialog box.
Recording CCO Hemodynamic Parameters
1.
Enter the “ViewBed” tab sheet.
2.
Select and then click CCO parameter area.
3.
Select the “CCO” tab sheet and click the “Hemodynamic Parameters” button.
4.
Click the “Record” button from the pop-up dialog box.
Recording SvO2/ScvO2 Oxygenation Parameters
1.
Enter the “ViewBed” tab sheet.
2.
Select and then click SvO2/ScvO2 parameter area.
3.
Select the “SvO2” or “ScvO2” tab sheet and click the “Oxygenation Parameters” button.
4.
Click the “Record” button from the pop-up dialog box.
Recording Real-time Waveforms
1.
Enter the “ViewBed” tab sheet.
2.
Select “Record” from the “Function” drop-down menu.
3.
Select a maximum of two (2) waveforms from the pop-up dialog box.
4.
Click “OK” to print out the selected waveforms.
or
11-8
1.
Enter the “Multibed” screen and select the desired patient window.
2.
Click the drop-down menu button.
3.
Select “Record” to print the displayed waveforms.
BeneVision CMS Operator‟s Manual
Recording Real-time Frozen Waveforms
1.
Enter the “ViewBed” tab sheet.
2.
Select “Freeze” from the “Function” drop-down menu.
3.
Select “Record” from the “Function” drop-down menu.
4.
Select a maximum of two (2) waveforms from the pop-up dialog box.
5.
Click “OK” to print out the selected waveforms.
Recording Real-time Alarms
If a parameter generates an alarm when its alarm switch and record switch are set to “ON”,
the CMS will initiate a real-time alarm recording.
11.1.3 Recording Control
By clicking the “System Setup” button then selecting the “Recording Control” tab, you can
enter a tab sheet.
In this tab sheet, the current tasks to be printed out are displayed. After selecting one task,
you can:
 Click the “Delete” button to delete this task.
 Click the “Move Up” button to increase its priority.
 Click the “Move Down” button to decrease its priority.
 Click the “Pause” button to pause this task.
 Click the “Continue” button to resume the paused task.
In this tab sheet, you can also:
 Click the “Record Type” drop-down menu to select desired record type.
 Click the “Sweep Speed” drop-down menu to select a desired waveform sweep speed
from the options of 25mm/s and 50mm/s.
 Select the check box before “Grid” to select whether to display the grid in the recording.
BeneVision CMS Operator‟s Manual
11-9
NOTE

The system can store a maximum of 50 print tasks or requests.

The paused task will not be printed out. If it is followed by other tasks to be
printed out, these tasks will be printed out through the recorder. The resumed
task will be printed out in correct order.

The real-time and ongoing recordings cannot be paused.

The automatically stopped recordings will record two lines of „*‟ at the end of
reports; manually stopped or abnormally stopped recordings will record one
line of „*‟ at the end of reports.
11.2 Print
11.2.1 Printing Support
The CMS can be connected with a local printer or network printer to print out reports. With a
separate power supply system, the local printer is directly connected to the CMS through the
general interface. The network printer is connected to the CMS through the network
interface.
The recommended printer types for the CMS are listed in the following table.
Printer type
Description
HP LaserJet M401n
HP LaserJet M602
HP LaserJet M605n
PDF Printer
Supports A4 or Letter sized paper.
Support to print electronic report. The PDF
printing needs to be enabled in the “Factory
Setup” menu.
You can purchase the printer directly from Mindray or buy the desired printer yourself. For
details about how to use the printer, refer to the accompanying document provided with the
printer.
11.2.2 Printing Contents
The following reports can be generated by the CMS:
 Patient Information
 Drug Calculations
 Hemodynamics Calculations
 Oxygenation Calculations
 Ventilation Calculations
11-10
BeneVision CMS Operator‟s Manual
 Renal Calculations
 Graphic or Tabular Trends
 Full Size Waveforms
 Waveform Segment Reports
 Compressed Waveforms
 Arrhythmia Statistics Results
 Event List
 Event
 C.O. Measurements
 12-Lead Analysis Results
 12-Lead Analysis Waveforms
 ST Segment Waveforms
 Real-time Report
 12-Lead ECGs
 Multi-lead ECGs
 EEG Waveforms
 ICG Hemodynamic Parameters
 CCO Hemodynamic Parameters
 SvO2/ScvO2 Oxygenation Parameters
 Alarm Settings Report
 Print on Alarm Report
 QT report
 Paging Assignment (CentralStation only)
11.2.3 Printing Operations
Printing Patient Information
1.
Enter the “Patient Mgmt.” tab sheet.
2.
Make sure the patient information is correct. If not, correct it and click “Save” button.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
Printing Drug Calculations
1.
Enter the “Drug Calcs” tab sheet.
BeneVision CMS Operator‟s Manual
11-11
2.
Perform drug calculation per 10.1 Drug Calculation.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
Printing Hemodynamics Calculations
1.
Enter the “Hemo Calcs” tab sheet.
2.
Perform hemodynamics calculation per 10.2 Hemodynamics Calculation.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
Printing Oxygenation Calculations
1.
Enter the “Oxygenation Calc.” tab sheet.
2.
Perform oxygenation calculation per 10.3 Oxygenation Calculation.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
Printing Ventilation Calculations
1.
Enter the “Ventilation Calc.” tab sheet.
2.
Perform ventilation calculation per 10.4 Ventilation Calculation.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
Printing Renal Calculations
1.
Enter the “Renal Calc.” tab sheet.
2.
Perform renal calculation per 10.5 Renal Calculation.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
11-12
BeneVision CMS Operator‟s Manual
Printing Graphic or Tabular Trends
Manual printing:
1.
Enter the “Trend Review” tab sheet.
2.
Set the resolution or zoom per 9.1.2 Trend Review.
3.
Click the icon on the right side of the “Print” button in the tabular trends and select
“Print Setup” to set up the printing options.
4.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
5.
Click the “Print” button.
Scheduled printing:
1.
Enter the “Trend Review” tab sheet.
2.
Click the icon on the right side of the “Print” button, and select “Scheduled Report
Setup” to set up the printing options.
3.
Click “Close” button to exit the menu. The report will be printed at the start time you set
in the printing control screen per 11.2.4 Printing Control. If you want to print the report
now, click “Print Now” button.
NOTE

The option “Scheduled Report Setup” is only available in the “Trend Review”
tab sheet when the check box before “Scheduled Report” is selected in the
“Printing Control” tab sheet.
Printing Full Size Waveforms
1.
Enter the “Full Disclosure” tab sheet. If compressed waveforms are displayed, click the
“Full Size” button in the lower right corner of the screen.
2.
Select the current review time.
3.
Click the icon on the right side of the “Print” button and select “Print Setup” to
perform print setups as prompted.
4.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
5.
Click the “Print” button.
BeneVision CMS Operator‟s Manual
11-13
Printing Waveform Segment Reports
1.
Enter the “Full Disclosure” tab sheet. If full size waveforms are displayed, click the
“Compressed” button in the lower right corner of the screen to change to the
Compressed Waveform view.
2.
Select the desired waveform groups by double-clicking to add them to the report. At
most, six (6) waveform groups can be printed on each page. You can also deselect a
waveform group by double clicking it again. The “Prev” and “Next” button can be used
to toggle between the selected waveform groups.
3.
Select “Print Preview” to preview the printout.
4.
Click the “Print All” button.
Printing Compressed Waveforms
1.
Enter the “Full Disclosure” tab sheet. If full size waveforms are displayed, click the
“Compressed” button in the lower right corner of the screen.
2.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
3.
Click the “Print” button.
Printing Arrh Statistics Results
1.
Enter the “Full Disclosure” tab sheet. If full size waveforms are displayed, click the
“Compressed” button in the lower right corner of the screen.
2.
Click the “Arrh Statistics” button to enter the “Arrh Statistics” menu where you can
view the statistics about the HR value and the number of each arrhythmia type that
occurred during a specified time range.
3.
Click the “Print” button.
Printing Event Lists
1.
Enter the “Event Review” tab sheet.
2.
Click the icon on the right side of “Print” button under the event list and select “Print
Setup” to set up the printing options.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
11-14
BeneVision CMS Operator‟s Manual
Printing an Event
1.
Enter the “Event Review” tab sheet.
2.
Select an event from the event list per 9.1.5 Event Review.
3.
Click the icon on the right side of “Print” button under the event parameter area and
select “Print Preview” to preview the printout.
4.
Click the “Print” button.
Printing C.O. Measurements
1.
Enter the “C.O. Review” tab sheet.
2.
Select one C.O. measurement.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
Printing 12-Lead Analysis Results
1.
Enter the “12-lead Review” tab sheet.
2.
Click the icon on the right side of the “Print” button and select “Print Setup” to set
the “Time Span”.
3.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
4.
Click the “Print” button.
Printing 12-Lead Analysis Waveforms
1.
Enter the “12-lead Review” tab sheet.
2.
Click the “Wave” button after an analysis result is selected.
3.
Click the icon on the right side of the “Print” button and select “Print Setup” to set up
the printing options.
4.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
5.
Click the “Print” button.
BeneVision CMS Operator‟s Manual
11-15
Printing ST Segment Waveforms
1.
Enter the “ST Review” tab sheet.
2.
Click the icon on the right side of the “Print” button and select “Print Preview” to
preview the printout.
3.
Click the “Print” button.
Printing Real-time Waveforms
1.
Enter the “ViewBed” tab sheet.
2.
Click the “Print” button.
3.
Select the desired waveforms from the pop-up dialog box.
4.
Click the “OK” button.
or
1.
Enter Multibed screen and select the desired patient window.
2.
Click the drop-down menu button.
3.
Click the “Print” to print the displayed waveforms.
Printing 12-Lead ECGs
1.
Enter the “12-lead ECG analysis” tab sheet from the monitor.
2.
Enter the “ViewBed” tab sheet from the CMS.
3.
Select “Show Multi-lead ECG” from the “View” drop-down menu to display the 12-lead
ECG waveforms.
4.
Select “Print” from the “Function” drop-down menu.
5.
In the pop-up dialog box, select “Print Layout”.
6.
Click the “OK” button.
Printing Multi-Lead ECGs
1.
Enter the “ViewBed” tab sheet.
2.
Select “Show Multi-lead ECG” from the “View” drop-down menu to display the multilead ECG waveforms.
3.
Select “Print” from the “Function” drop-down menu.
11-16
BeneVision CMS Operator‟s Manual
Printing EEG Waveforms
1.
Enter the “ViewBed” tab sheet.
2.
Select “BIS Expand View” from the “View” drop-down menu.
3.
Click the “Display” button and select “EEG” from the pop-up drop-down menu.
4.
Click the “Print” button.
Printing ICG Hemodynamic Parameters
1.
Enter the “ViewBed” tab sheet.
2.
Select and then click ICG parameter area.
3.
Select the “ICG” tab sheet and click the “Hemodynamic Parameters” button.
4.
Click the “Print” button from the pop-up dialog box.
Printing CCO Hemodynamic Parameters
1.
Enter the “ViewBed” tab sheet.
2.
Select and then click CCO parameter area.
3.
Select the “CCO” tab sheet and click the “Hemodynamic Parameters” button.
4.
Click the “Print” button from the pop-up dialog box.
Printing SvO2/ScvO2 Oxygenation Parameters
1.
Enter the “ViewBed” tab sheet.
2.
Select and then click SvO2/ScvO2 parameter area.
3.
Select the “SvO2” or “ScvO2” tab sheet and click the “Oxygenation Parameters” button.
4.
Click the “Print” button from the pop-up dialog box.
Printing Alarm Settings Report
1.
Enter “Alarm Setup” screen as per 8.4 Alarm Setup.
2.
Click “Print” button.
Printing on Alarm Report
If a parameter generates an alarm when its alarm switch and print switch are set to “ON”, the
CentralStation will initiate a real-time alarm printing.
BeneVision CMS Operator‟s Manual
11-17
Printing QT Report (Telemetry Only)
When the Telemetry is using Mindray algorithm, the QT report can be printed.
1.
Enter the “ViewBed” tab sheet.
2.
Select and then click “ECG” parameter area.
3.
Click “QT View” button.
4.
Click “Print” button.
Printing Paging Assignment
1.
Enter the “Paging Assignment” tab as per 13.2 Accessing Paging.
2.
Select “Paging Assignment” tab.
3.
Click “Print” button.
Remotely Printing Real-time ECG Waveforms from Bedside
NOTE

This function is only applicable when connecting Passport V and Spectrum
bedside monitors.
In the View screen of the bedside monitors, select the “Strip” button. The CentralStation will
initiate a real-time waveform printing.
Remotely Printing Graphic or Tabular Trends from Bedside
NOTE

This function is only applicable when connecting Passport V and Spectrum
bedside monitors.
1.
Enter the Trends screen on the bedside monitor.
2.
Select “List Trends” or “Graphic Trends” on the bedside monitor.
3.
Click “Print Trend” button. The CentralStation will initiate the printing.
11-18
BeneVision CMS Operator‟s Manual
Remotely Printing 12-Lead ECG Waveforms from Bedside
NOTE

This function is only applicable when connecting Passport V and Spectrum
bedside monitors.
1.
Enter the 12-Lead screen on the bedside monitor.
2.
Select “Strip” button on the bedside monitor.
3.
Click “Print Trend”. The CentralStation will initiate the printing.
11.2.4 Printing Control
By clicking the “System Setup” button and then selecting the “Printing Control” tab, you can
select local printer or network printer from the printer drop-down list.
In the tab sheet, the current tasks to be printed are displayed. After selecting one task, you
can:
 Click the “Delete” button to delete this task.
 Click the “Pause” button to pause this task.
 Click the “Continue” button to resume the paused task.
 Click the “Delete All” button to delete all printing tasks.
You can set up printing in the “Print Setup” area on the right side of the sheet.
 Sweep Speed: select a sweep speed for the waveform from the options of 12.5mm/s,
25mm/s and 50mm/s.
 12-Lead Printout Sequence: set the printing mode in 12-lead ECG report.

“Simultaneous”: print simultaneous 12-lead ECG data.

“Sequential”: The 12-lead ECG data of a certain period is sequentially printed. The
period is decided by the print layout setting. For example, when the print layout is
set to 6×2+1, the l2 leads are allocated into two columns. The time span of each
column is 5 seconds: the first column is 0-5s waveforms; the second column is 5s10s waveforms. One row of rhythm waveform is located at the bottom.
 Grid: Select if grid is printed.
You can set up scheduled report printing in the “Scheduled Report Setup” area on the right
side of the sheet.
BeneVision CMS Operator‟s Manual
11-19
 Scheduled Report: select or deselect the checkbox before “Scheduled Report” to switch
the periodic report print on or off .
 Start Time: set up the start time to print.
 Interval: set up the desired interval.
NOTE

If printing fails, restart the printer and press the “Restart Print Service” button
to resume.

When a network printer is selected, only printing tasks of the CMS are
displayed. The printing tasks of other networks are not displayed.

The option “Scheduled Report Setup” is available in the “Trend Review” tab
sheet only when the check box before “Scheduled Report” is selected in the
“Printing Control” tab sheet.
11.3 Save As
The CMS can save the following items as HTML files:
 Graphic trends
 Tabular trends
 Full disclosure
 C.O. review
 Event list review
 Event review
 Drug calculations
 Hemodynamics calculations
 Oxygenation calculations
 Ventilation calculations
 Renal calculations
 12-lead review
 DSA graph
With the file name defaulted as “XXXX-patient name YYYY”, in which the “XXXX”
represents one of the above items. If no patient name is input, the file name will have no
patient name. If it is the first time saving, the “YYYY” will be 0001, which will
automatically add one (1) every time data is saved.
The saved files can be browsed using Internet Explorer on other computers.
11-20
BeneVision CMS Operator‟s Manual
The files can be saved to a mobile hard disk, flash, or the like, which must be connected to
the CMS before saving. If no storage device is connected, the system will give the “No valid
storage device found in the system, please confirm!” message.
After a USB device is successfully connected to the CMS, the
icon will appear in the
system icon area.
To disconnect the USB device from the CMS:
1.
Click the
icon.
2.
Click the “Delete disk driver safely” prompt.
3.
After the
icon disappears, you can disconnect the USB device from the CMS.
Graphic Trends
1.
Enter the “Trend Review” tab sheet.
2.
If tabular trends are currently displayed on the screen, click the “Graphic” button.
3.
Click the “Save As” button. A dialog box will be displayed.
4.
Select a drive and click “OK”. The graphic currently displayed on the screen will be
saved to the selected storage disk.
Tabular Trends
1.
Enter the “Trend Review” tab sheet.
2.
If graphic trends are currently displayed on the screen, click the “Tabular” button.
3.
Click the “Save As” button. A dialog box will be displayed.
4.
Select a time range and click “OK”. The “Save As” dialog box will be displayed.
NOTE

The system will save the data within the time range prior to save the start time.
5.
Select a disk driver name and click “OK”. The data in the tabular trends will be saved to
the selected storage disk.
Full Size Waveform
1.
Click the “Full Disclosure” tab sheet. If compressed waves are displayed, click the “Full
Size” button in the lower right corner of the screen.
2.
For operation details, refer to 9.1.3 Full Disclosure.
BeneVision CMS Operator‟s Manual
11-21
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4.
Select a drive and click “OK”. The waveforms currently displayed on the screen will be
saved to the selected storage disk.
Compressed Waveform
1.
Click the “Full Disclosure” tab sheet. If full size waveforms are displayed, click the
“Compressed” button in the lower right corner of the screen.
2.
For operation details, refer to 9.1.3 Full Disclosure.
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4.
Select a disk driver name and click “OK”. The waveforms currently displayed on the
screen will be saved to the selected storage disk.
C.O. Review
1.
Enter the “C.O. Review” tab sheet.
2.
Select the C.O. measurements to be saved per 9.1.4 C.O. Review.
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4.
Select a disk driver name and click “OK”. The currently selected C.O. measurements
will be saved to the selected storage disk.
Event List Review
1.
Enter the “Event Review” tab sheet.
2.
Select “Filter by Event” and “Filter by Priority”.
3.
Click the “Save As” button below the event list. The “Save As” dialog box will be
displayed.
4.
Select a disk driver name and click “OK”. The contents in the event list will be saved to
the selected storage disk.
Event Review
1.
Enter the “Event Review” tab sheet.
2.
Select an event from the event list.
3.
Click the “Save As” button below the event parameter area. The “Save As” dialog box
will be displayed.
4.
Select a disk driver name and click “OK”. The waveforms and parameters of the event
will be saved to the selected storage disk.
11-22
BeneVision CMS Operator‟s Manual
Drug Calculation
1.
Enter the “Drug Calcs” tab sheet.
2.
Perform drug calculation per 10.1 Drug Calculation.
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4.
Select a disk driver name and click “OK”. This set of drug calculations will be saved.
Hemodynamics Calculation
1.
Enter the “Hemo Calcs” tab sheet.
2.
Perform hemodynamics calculation per 10.2 Hemodynamics Calculation.
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4.
Select a disk driver name and click “OK”. This set of hemodynamics calculations will
be saved.
Oxygenation Calculation
1.
Enter the “Oxygenation Calc.” tab sheet.
2.
Perform oxygenation calculation per 10.3 Oxygenation Calculation.
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4.
Select a disk driver name and click “OK”. This set of oxygenation calculations will be
saved.
Ventilation Calculation
1.
Enter the “Ventilation Calc.” tab sheet.
2.
Perform ventilation calculation per 10.4 Ventilation Calculation.
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4.
Select a disk driver name and click “OK”. This set of ventilation calculations will be
saved.
Renal Calculation
1.
Enter the “Renal Calc.” tab sheet.
2.
Perform renal calculation per 10.5 Renal Calculation.
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4.
Select a disk driver name and click “OK”. This set of renal calculations will be saved.
BeneVision CMS Operator‟s Manual
11-23
12-Lead Analysis Results
1.
Enter the “12-lead Review” tab sheet.
2.
Click the “Save As” button. The “Save As” dialog box will be displayed.
3.
Select a disk driver name and click “OK”. The 12-lead analysis result list will be saved.
12-Lead Analysis Waveforms
1.
Enter the “12-lead Review” tab sheet.
2.
Click the “Wave” button after an analysis result is selected.
3.
Click the “Save As” button. The “Save As” dialog box will be displayed.
4. Select a disk driver name and click “OK”. The 12-lead analysis waveforms will be saved.
DSA Graph
1.
Enter the “BIS Expand View” tab sheet.
2.
Click the “Display” button and select “DSA” from the pop-up drop-down menu.
3.
Click the “Save As” button.
4.
Select a disk driver name and click “OK”. The DSA graph will be saved.
11-24
BeneVision CMS Operator‟s Manual
12 System Setup
12.1 General Setup
Clicking the “System Setup” will access a tab sheet.
The CMS has three levels of setup:
 Low level:
“General Setup”
 Medium level: “Admin Setup”
 High level:
“Factory Setup”
Certain authority is required if you want to modify some system configurations or execute
certain operations. The user with lower authority cannot modify the configuration of the user
with higher authority, but the user with higher authority can modify the setups of the user
with lower authority.
When the system starts, the default setup is the “General Setup”. The “Factory Setup” is
intended for use only by manufacturer-designated personnel.
In the “General Setup” tab sheet, you can:
Set Alarm Volume
The system provides 10 volume levels. You can select one as required. For details, refer to
12.2.3 Alarm - Setting Minimum Alarm Volume and 8.3 Alarm Volume.
BeneVision CMS Operator‟s Manual
12-1
Draw Waveform Type
There are two options:
 COLOR: Selecting this option allows you to see smoothed waveforms.
Figure 12-1 Color Drawing
 MONO: Selecting this option allows you to see unprocessed waveforms.
Figure 12-2 Mono Drawing
Set Display Grid
You can set whether to display the grid in the waveform area.
Set Unit
Click the “Unit Setup” button to enter the Unit Setup screen. You can set unit for each
parameter of the following modules as required:
12-2
Module
Parameter
Options
Defaults
NIBP
NIBP
mmHg, kPa
mmHg
CO2
CO2
mmHg, kPa
mmHg
TEMP
T1, T2, TD, TB
℃, ℉
℃
ECG
ST
mV, mm
mV
5
Vascular Resistance
SVR/PVR
DS/cm , kPa-s/l
DS/cm5
Oxygenation
Hb
g/dl, g/l, mmol/l
g/dl
BeneVision CMS Operator‟s Manual
Module
Parameter
Options
Defaults
IBP
IBP
mmHg, kPa, cmH2O
mmHg
CO2
mmHg, kPa, %
mmHg
O2
mmHg, kPa, %
mmHg
Pressure
cmH2O, mbar, hpa
cmH2O
CO2
mmHg, kPa, mbar, hpa
mmHg
tcpCO2/tcpO2
mmHg, kpa
mmHg
Glucose
Glucose
mmol/L, mg/dl
mmol/L
I/O Fluid
I/O Fluid
ml, L
ml
GAS
Device Intergration
Enter Admin Setup
By clicking the “Admin Setup” button and inputting the required password, you can enter the
Admin Setup menu. For details, refer to 12.2 Admin Setup.
Enter Factory Setup
By clicking the “Factory Setup” button and inputting the required password, you can enter
the Factory Setup menu. As the “Factory Setup” is intended for use only by manufacturerdesignated personnel, no details will be given in this manual.
12.2 Admin Setup
Click the “Admin Setup” button in the “General Setup” tab sheet. The “Enter Password”
dialog box will pop up. After inputting the required password, select “OK” to enter a tab
sheet.
12.2.1 Setting Color
On the CMS screen, all related information of one monitored parameter appears in the same
color. The related information includes real-time waveforms (including waveform name, gain
and filter mode), real-time parameter values (including high and low limits), reviewed
waveforms (including waveform name, gain and filter mode), etc. You can set color for each
monitored parameter and arrhythmia mark as required.
Procedure
1.
Enter the “Color” tab sheet and then select a parameter or Arrh mark whose color you
want to change.
BeneVision CMS Operator‟s Manual
12-3
2.
Click the color box corresponding to the parameter or Arrh mark, and a list of available
colors will be displayed.
3.
Select your desired color from the list.
4.
If you want a color that is not in the list, click “Others” to enter the window, through
which you can define a color you want.
5.
Select a color and click “OK”.
12.2.2 Display Setup
You can set screen size, number of main screen /display layout, multibed display, multibed
window layout and auxiliary window.
Screen Size
1.
Click the “Display Setup” tab.
2.
Select the display type from the “Screen” drop-down menu.
3.
Click the “Close” button.
NOTE

The screen size setting change will take effect after the CMS restarts.
The CentralStation, WorkStation or ViewStation each can support connecting up to four (4)
displays. It will check the number of displays every time it starts. When more than one
display is used simultaneously, they should adopt the same screen size and resolution. To
ensure normal displaying, you should select the screen size of the display actually used and
the display resolution should be set to 1280 x 1024 pixels. Setting resolution to other pixels
may cause a display error.
Number of Main Screen
Select a number for the item “Number of Main Screen” to change the displaying mode when
the CentralStation, WorkStation or ViewStation is equipped with more than one display. The
displays can be set without auxiliary screen, or with only one auxiliary screen.
The display number and configurable main screen number are shown in the following table.
Display Number
Options for Number of Main Screen
2
3
4
1, 2
2, 3
3, 4
Take the two displays as an example.
12-4
BeneVision CMS Operator‟s Manual
 If “1” is selected, there is only one main screen which always displays the multibed
screen. The other display is the auxiliary screen, always for single bed window and
system menu.
 If “2” is selected, the two screens are both able to be used as the main screen. If you want
to view a single bed, the single bed window will be shown in one display; if not, the two
screens will both show multibed screen.
Display Layout
If a CentralStation, a WorkStation or a ViewStation is equipped with four displays, select the
option of “1×4” or “2×2” for “Display Layout” to change the cursor moving mode.
 When the four displays are arranged in a line, select “1×4”. You can move the cursor
from current display to its neighboring diplays, as shown in Figure 12-3.
1
2
3
4
Figure 12-3 Cursor Moving Mode: 1×4
 When two displays are stacked on the other two displays, select “2×2”. You can move
the cursor from current display to its neighboring displays, as shown in Figure 12-4.
1
2
3
4
Figure 12-4 Cursor Moving Mode: 2×2
NOTE

The display setting changes will take effect after the CMS restarts.
Multibed Display
 Select/deselect the check box before “Measurement Units” to show/hide parameter units
on the multibed screen.
BeneVision CMS Operator‟s Manual
12-5
 Select/deselect the check box before “Patient Name” to show/hide patient name on the
multibed screen. By default, the “Patient Name” is selected on the CentralStation and
WorkStation, and is deselected on the ViewStation.
 In “Name Displaying Hotkey”, you can set the hotkey which can be used to display the
name in the first waveform area of the patient window on the multibed screen. The
default hotkey is F9. If the check box before “Patient Name” is not selected, the patient‟s
name displays when you press the hotkey, and the name does not display after 30 seconds
or when you press the hotkey again.
 In “Change to Idle Sector” (only available on CentralStation), you can configure the
switch of setting to an idle sector in multibed screen:

If “Enable” is selected, the drop-down list of a “No patient admitted or patient
transferred” patient window on multibed screen will display the option “Change to
Idle Sector”;

If “Disable” is selected, the drop-down list of a “No patient admitted or patient
transferred” patient window on multibed screen will not display the option “Change
to Idle Sector”.
Multibed View Window Layout
You can select the number of rows and columns for the multibed view window based on your
actual needs. The range for the number of rows is 2 to 8, and for the number of columns is 1
to 3. The product of the number of rows and the number of columns is the number of patient
sectors. The number of patient sectors on a single screen cannot exceed 16. After the number
of rows and columns are selected, you can preview the new layout set on the right side of the
screen.
After the number of rows and columns are selected, the settings of the multibed view window
layout take effect.
ECG Lead Sequence
You can choose an option from “Standard” and “Cabrera” for “ECG Lead” to set waveform
sequence for multi-lead ECG:
 Standard: I, II, III, aVR, aVL, aVF, V1, V2, V3, V4, V5, V6
 Cabrera: aVL, I, -aVR, II, aVF, III, V1, V2, V3, V4, V5, V6
The default multi-lead ECG sequence is “Standard”.
After the ECG lead sequence is set, the waveform sequence will be updated in the following:
 The display in 12-lead review
 The realtime display in multi-lead ECG screen
12-6
BeneVision CMS Operator‟s Manual
 12-lead analysis waveform report
 12-lead analysis waveform strip
 The XML file of 12-lead analysis waveform
 12-lead ECG report
 Multi-lead ECG report
Soft Keyboard
The soft keyboard is to support the CMS configured with touchscreen. The soft keyboard can
be set to “On” or “Off”.

“On” is selected.

A soft keyboard displays when a field that requires an input is selected.

The touchscreen controls are enabled.
 “Off” is selected.

No soft keyboard displays when a field that requires an input is selected.

The touchscreen controls are disabled.
Touchscreen Calibration
Select this button, and perform the procedures according to the screen prompts to calibrate
the touchscreen.
Device Assignment Passport (WorkStation and ViewStation Only)
Accessing the Device Assignment screen on the WorkStation and ViewStation can be
password protected.
Select the check box before “Device Assignment Password Protection”, a password dialog
box will display after selecting the “Device Assignment” system button. You are required to
enter the correct password to access the Device Assignment screen. Otherwise, no such
password dialog box displays.
Auxiliary Window Setup
Auxiliary window setup allows you to set the tab sheets on the single bed window. The six
functional items of patient management, ViewBed, full disclosure, trend review, event review
and display setup are fixed to be selected while ST review, 12-lead review, C.O. review, drug
calculation, hemodynamic calculation, OxyCRG calculation, renal calculation and ventilation
calculation are user selectable. You can change the display order of the functional items via
the “Move Up”, “Move Down”, “Move First” and “Move Last” buttons on the right side of
BeneVision CMS Operator‟s Manual
12-7
the dialog box.
After the functional items are set, click “OK” to activate the setting.
12.2.3 Alarm
Click “Alarm” to open a dialog box.
Setting Minimum Alarm Volume
The minimum alarm volume level can be set from 1 to 10.
Setting Alarm Audio Mode
You can set the alarm audio mode as “ISO”, “MODE 1” or “MODE 2”.
Setting Alarm Sound Intervals
If the alarm audio mode is set as “ISO”, you can set alarm sound intervals by toggling
between “High Alarm Interval (s)”, “Med Alarm Interval (s)” and “Low Alarm Interval (s)”.
You cannot change the interval between alarm tones if you choose mode 1 or 2 as your
desired alarm audio mode. For these two modes, the interval between alarm tones identifies
the alarm levels as follows:
 Mode 1:

Interval between high level alarm tones:

Interval between medium level alarm tones: 5 s

Interval between low level alarm tones:
continuously
20 s
 Mode 2:

Interval between high level alarm tones:

Interval between medium level alarm tones: 5 s

Interval between low level alarm tones:
1s
20 s
Setting Simulated Alarm Light
You can switch on/off the simulated alarm light in the Multibed and ViewBed screens. By
default, the simulated alarm light is switched on.
 If “On” is selected, the alarm message background will flash.
 If “Off” is selected, the alarm message background will not flash.
12-8
BeneVision CMS Operator‟s Manual
Selecting Stored Waveforms (CentralStation Only)
In the “Alarm” tab sheet, you can select the relevant waves stored when alarms occur within
the specific parameter.
1.
Click the “Alarm” tab sheet.
2.
Select a parameter from the “Alarm Numeric” list. Then select the relevant wave stored
from the “Related Waveform” when the alarm occurred.
3.
Click “Save” to save the selected wave.
4.
Click “Default” to restore all parameters to the default configuration.
NOTE

No matter how many waveforms are selected from the Related Waveform list, the
system can at most save three (3) waveforms and record two (2) waveforms for
one parameter when an alarm occurs.

Your selections are only effective for later alarms. For already existing alarms, it
is unnecessary to re-select waveforms.
12.2.4 Trend Group
You can set the parameters in “Trend Review” by group.
The Trend Group tab sheet contains a system default trend groups list, a custom trend groups
list, and the list of corresponding trend group member parameters. The system provides the
following default trend groups: “All”, “Standard”, “ECG”, “GAS”, “Hemodynamic”, “RM”,
“BIS”, “Ventilator” and “Anesthesia”. You cannot edit the default trend groups.
 Create trend group click “New Group” and enter the name of custom trend group in the
pop-up dialog box.
 Edit trend group after selecting a custom trend group, you can select/deselect the member
parameters or adjust the order of member parameters in the list.
 Save trend group after creating or editing a trend group, click “Save Group” to save the
new or modified trend group.
 Delete trend group you can delete any custom trend group from the trend group list.
 Rename trend group click the custom trend group to be renamed, enter the new name of
the trend group in the pop-up dialog box.
BeneVision CMS Operator‟s Manual
12-9
12.2.5 Monitor List (CentralStation Only)
Clicking the “Monitor List” will enter a tab sheet, which lists all the connected monitors in
the LAN including the monitors admitted by this CentralStation.
The monitor list does not include the manually connected monitors and CMS protocol
monitors. Refer to the monitor‟s operator‟s manual for connecting to a CentralStation.
The displayed items are:
 Monitor name
 Unit
 Bed no.
 IP address
 Connected status
Refresh
You can update the list by clicking the “Refresh” button.
Admit
You can select the monitor with the monitoring status of “Not admitted by CMS” and then
click the “Admit” button to admit it to this CentralStation.
Cancel
You can select the monitor with the monitoring status of “Admitted by this CMS” and then
click the “Cancel” button to cancel the admission.
Cancel All
You can click the “Cancel All” button to cancel this CentralStation‟s admission of all the
monitors.
Admit All Current Unit's Monitors
You can admit all current unit‟s monitors to this CentralStation by clicking the “Admit All
Current Unit's Monitors” button. If “Auto Admit All Current Unit's Monitors” is selected, the
admission can be done automatically.
12-10
BeneVision CMS Operator‟s Manual
12.2.6 Telemetry (CentralStation Only)
If your CentralStation is connected with the telemetry, select the “Telemetry” tab. You can set
the following items in an opened tab sheet.
12.2.6.1 Alarm Setup
You can set the following alarm items for telemetry transmitters at the CentralStation.
Alarm Delay
If the alarm-triggered condition disappears within the delay time, the CentralStation does not
give the alarm.
You can set telemetry alarm delay time (6 s by default) and ST alarm delay time (30 s by
default). After the desired time is set to the alarm delay, the associated physiological alarms
include: HR too high, HR too low, SpO2 too high, SpO2 too low, PR too high, PR too low,
QTc too high, ΔQTc too high, and SpO2 Desat.
NOTE

The telemetry alarm system delay times are not greater than 10 seconds except
for the ST alarm. The least delay time for ST alarm is 30 seconds.

The alarm delay time for the following technical alarms is factory default 5
seconds:

SpO2 Sensor Off

SpO2 Too Much Light

SpO2 Low Signal

SpO2 Interference
Alarm Latched
Alarm latching denotes that the audio and visual indicators, associated with an alarm
condition, do not automatically stop after resolving the alarm condition. After resolving the
condition, it must be acknowledged or the audio and visual indicators continue. The alarm
triggered time displays after the alarm messages.
To set “Alarm Latched”, you can select one of four options listed below:

“Off”: no alarm will be latched.

“High Only”: the alarms in the high level will be latched.

“Hi&Med”: the alarms in the high and medium levels will be latched.

“All”: all alarms will be latched.
To clear the latched alarm, you can select “Alarm Reset” or “Enter Alarm Paused State” from
BeneVision CMS Operator‟s Manual
12-11
the “Function” drop-down menu.
Alarm Priority
You can set the “Alm Lev of ECG Lead Off”, “Alm Lev of SpO2 Sensor Off” and “Alm Lev
of No RF signal” to “High”, “Med” or “Low”. The default settings for the three options are as
follows:

“Alm Lev of ECG Lead Off”: Low.

“Alm Lev of SpO2 Sensor Off”: Low.

“Alm Lev of No RF Signal”: Med.
Alarm Reset
You can set the duration for the alarm reset. The setting options include: "1 min", "2 min", "3
min", and "Permanence". The default is "Permanence".
Lethal Arrh Off Settings for Arrhythmia Alarms
“Lethal Arrh OFF” can be set for the telemetry monitoring system.
 If it is set to “Disable”, all the lethal Arrhythmia alarms switches are set to “ON” and are
unchangeable. The “All Alarms Off” button is inactive.
 If it is set to “Enable”, the switches of lethal Arrhythmia alarms are able to be set. The
“All Alarms Off” button is active.
Monitoring Mode Setup
Monitoring mode setup establishes a corresponding connection between the telemetry
transmitter and multibed patient sector. The CentralStation provides two monitoring modes:
 Fixed Monitoring: to establish fixed corresponding connections between the telemetry
transmitter and the multibed patient sector. Such corresponding connections are not
changed when the patient is discharged. The patient sector displays bed number and serial
number of the telemetry transmitter and the bed mark color is not changed. The patient
sector displays “No patient admitted or patient transferred”.
 Flexible Monitoring: no fixed corresponding connections are established between the
telemetry transmitter and multibed patient sector. The corresponding connections are
relieved when the patient is discharged. The patient sector is idle and displays “Idle
sector”.
Click the “Monitoring Mode Setup” button and select the telemetry monitoring mode from
12-12
BeneVision CMS Operator‟s Manual
the pop-up menu. The options are “Fixed Monitoring” and “Flexible Monitoring”. The setting
is activated immediately.
Analysis Lead Setup
The CentralStation uses information from two leads to detect beats and to compute heart rate
(HR). These two leads are referred to as the primary and secondary leads. For Mortara ECG
algorithm, information from an additional lead (analysis lead) is used to classify the beats
(normal, abnormal and so on). The user can select any of the available leads (depending on
whether a 3 or 5 lead cable is used) as primary, secondary or classification leads.
The ECG lead waveforms displayed in the waveform area are defined as the displaying lead.
You can set whether or not the analysis leads are consistent with the displaying leads by
making adjustments in the “Consistent with Displayed Lead” option. For details about
different transmitter analysis lead configurations, refer to the telemetry monitoring system
operator‟s manual for details.
Nurse Call and event
There are two options: “Nurse Call and event” and “Nurse Call Audio Mode”.
 “Nurse Call and event”: enable or disable the nurse call and/or event function for the
telemetry transmitters.

“Disable”: disables nurse call and event functions.
For the TMS-6016 transmitter, there are no fields of “Nurse Call” and “Event” in
the Patient Mgmt. screen.
For the TMS60 or Panorama Telepack-608 transmitter, there are no fields of
“Nurse Call” in the Patient Mgmt. screen.

“Enable”: enables the nurse call and event functions.
For the TMS-6016 transmitter, the Patient Mgmt. screen displays the “Nurse Call”
and “Event” fields.
For the TMS60 or Panorama Telepack-608 transmitter, the Patient Mgmt. Screen
only displays the “Nurse Call” field.

“Event”: enables the event function, and the Patient Mgmt. screen displays the
“Event” field. This setting is only applied for the TMS-6016 transmitter.

“Nurse Call”: enables the nurse call function, and the Patient Mgmt. screen
displays the “Nurse Call” field.
 “Nurse Call Audio Mode”: sets the nurse call audio mode as “MODE 1”, “MODE 2”, or
“Standard”. The default setting is “Standard”.
Frequency Setup
You can set or change the IP address and frequency, and view the system information for the
BeneVision CMS Operator‟s Manual
12-13
telemetry receivers.
For details about different transmitter frequency setup, refer to the corresponding telemetry
monitoring system operator‟s manual for details.
12.2.6.2 Telepack 608
Program
You can program for the Telepack-608 transmitter, and assign a receiving channel for the unprogrammed transmitter.
Device Info
Display the device information, such as Device ID, Bad Segment, Bad Packet, and so on for
the Telepack-608 transmitter connected to the CentralStation.
12.2.7 Log
Clicking the “Log” tab will enter a tab sheet, which records the operating status of the
CentralStation providing a convenient way for service personnel to track and maintain the
system. Each log includes occurrence time, log level, and log description.
A total loss of power has no impact on the saved logs. The earlier-recorded logs may be
cleared and new logs are added if the log capacity is reached.
Delete
You can delete all logs by clicking the “Delete All” button.
Refresh
You can update the logs by clicking the “Refresh” button.
Export
To export the logs:
1.
Click the “Export” button. The “Save As” dialog box will be displayed.
2.
Select a disk to which the logs are exported. The disk can be a local hard disk, mobile
hard disk or USB.
3.
The default file name is “cmsXXXX”. If it is the first time saving, the “XXXX” will be
0001, which will automatically add 1 every time a log is saved. You can change the file
name as required.
4.
Click “OK” to initiate exporting data.
12-14
BeneVision CMS Operator‟s Manual
5.
Click “Cancel” to cancel exporting data.
12.2.8 Other
Clicking the “Other” button will enter a tab sheet. The CentralStation, WorkStation and
ViewStation include different functions.
12.2.8.1 Shutdown Requires Password
If this option is turned on, you need to input a password before shutting down the system.
12.2.8.2 Change Language
The CMS has multiple languages available, from which you can choose any one as required.
When the CMS starts, the default language is the language selected at time of installation.
1.
Click the “Change Language” button. The dialog box will be displayed.
2.
Click the down arrow button to view a list of available languages.
3.
Select the desired language. It is recommended to select the ones registered at time of
installation and supported by the operating system.
4.
Click the “OK” button.
5.
If the language you have selected is not supported by the operating system, a message
will be displayed.
NOTE

If the language you selected is inconsistent with that of the operating system,
unrecognizable characters may appear on the CMS. If this occurs, change the
operating system language and region settings by following the operating system
operator‟s manual.
12.2.8.3 Change User Password
1.
Click the “Change User Password” button. The dialog box will be displayed.
2.
Input old password and new password before selecting “OK”.
3.
If the change succeeds, the “Password changed. Please remember new password.”
message box will be displayed. Select “OK” to activate your change.
4.
If the old password you have entered is incorrect or the new password is entered
incorrectly, the system will give a prompt message. You can select “OK” to repeat the
input procedure.
BeneVision CMS Operator‟s Manual
12-15
NOTE

If you use the factory password to enter the “Admin Setup” tab sheet, you can
directly input the new password without inputting the old password.
12.2.8.4 Time Setup
WARNING

Do not change the operating system time if the CMS software is installed.
NOTE

After the CentralStation time is changed, the networked monitor system time will
be synchronized to match the CentralStation system time.

When a monitor is connected to the CentralStation, the monitor system time will
be synchronized to match the CentralStation system time.

The CentralStation will synchronize the time of the networked monitors at start
of every hour.
The CMS system time can be changed automatically or manually.
Automatically change time:
1.
Click the “Time Setup” button, and the dialog box will be displayed.
2.
Set “Time Synchronization” to “Master Server” or “NTP Server”.
3.

“Master Server” :Set the time to synchronize with master server.

“NTP Server”: Set the time to synchronize with NTP server. Input master time
server IP and second time server IP.
Click “OK”.
Manually change time:
1.
Click the “Change Time” button, and the dialog box will be displayed.
2.
Set “Time Synchronization” to “Manual”.
3.
Adjust the “Set System Time” setting by selecting the date and time field and entering
the number, or by clicking the drop-down arrow and selecting a date or time from the
table.
4.
Click “OK”.
12-16
BeneVision CMS Operator‟s Manual
12.2.8.5 Change Hospital Name
1.
Click the “Change Hospital Name” button.
2.
Input hospital name and unit name.
3.
Select “OK”.
NOTE

Hospital name should be within 128 characters,and department name should
be within 8 characters.
12.2.8.6 Communication Settings
Refer to 12.3 Communication Settings for details.
12.2.8.7 Remote Control Settings (CentralStation and WorkStation Only)
CentralStation
In Remote Control Settings menu on the CentralStation, you can make the following settings.
By default, all are deselected.
 Alarm Setup: select or deselect the checkbox before “Alarm Setup” to switch on or off
remote alarm setup. If the checkbox is selected, you can remotely change the settings of
activation state, alarm priority, alarm high/low limit, Arrh threshold, Apnea alarm time
and Desat limit of the monitor. If the checkbox is not selected, you can not change those
settings on the CentralStation.
 Alarm Paused & Alarm Reset: Select the checkbox before “Alarm Paused & Alarm Reset”
to switch on/off alarm paused or alarm reset function. If the checkbox is selected, you can
remotely control the alarm pause or alarm reset of the bedside monitors on the
CentralStation. The corresponding controls are available in the drop-down menu of the
spot patient window and the “Function” drop-down menu of ViewBed screen are active.
If the checkbox is not selected, you cannot use those functions.
 Privacy Mode: Select the checkbox before “Privacy Mode” to turn on/off this function.
When “Privacy Mode” is selected, you can remotely control the bedside monitor to enter
privacy mode. The corresponding control is available in the drop-down menu of the spot
patient window. If it is not selected, you cannot use this function. The corresponding
control is unavailable in the drop-down menu of the spot patient window.
 Night Mode: Select the checkbox before “Night Mode” to turn on/off this function. When
“Night Mode” is selected, you can remotely control the bedside monitor to enter Night
mode. The corresponding control is available in the drop-down menu of the spot patient
window. If it is not selected, you cannot use this function. The corresponding control is
unavailable in the drop-down menu of the spot patient window.
BeneVision CMS Operator‟s Manual
12-17
NOTE

When the CentralStation restarts, the “Alarm Setup”, “Alarm Paused & Alarm
Reset”, “Privacy Mode” and “Night Mode” checkboxes remain the same as
when the CentralStation was last turned off.
WorkStation
In the Remote Control Settings menu on the WorkStation, you can select the check box
before each function and then remotely control the corresponding functions of the bedside
monitors. If the checkbox is not selected, you cannot use the function on the Work Station:
 Patient Mgmt

Patient Info

Discharge

Standby
 Alarm Paused & Alarm Reset

Alarm Paused

Alarm Reset
 NIBP Measurement

Start/Stop NIBP Measurement

Interval

Clock
 Night Mode & Privacy mode

Night Mode

Privacy Mode
 Parameter Alarm Settings

Activation State

Alarm Priority

Alarm Limit

Apnea Delay

Sat-Seconds
 Arrhythmia Alarms

Activation State

Alarm Priority

Arrh threshold
 Pacer Settings
12-18
BeneVision CMS Operator‟s Manual

Pacer Rate

Pacer Reject
 Define ST point
 ECG Learning
NOTE

When the WorkStation restarts, the “Alarm Setup”, “Alarm Paused & Alarm
Reset”, “Privacy Mode” and “Night Mode” checkboxes remain the same as
when the WorkStation was last turned off.
12.2.8.8 Patient Location Setting (CentralStation and WorkStation Only)
The patient window and ViewBed screens can display the patient location when the bedside
device is in Standby mode. The available locations include:
 Unspecified
 Cathlab
 X-Ray
 MRI
 CI scan
 Ultrasound
 Hemodialysis
 OR
 Therapy
By default, the patient window and ViewBed screens display “Not Specified” when the
device is in Standby mode.
In the Patient Location Setting screen, after selecting one location, you can:
 Click the “Delete” button to delete this location.
 Click the “Move Up” button to move the location up in the list.
 Click the “Move Down” button to move the location down in the list.
 Click “Modify” button to modify a location.
In the Patient Location Setting screen, you also can:
 Click the “Default” button to restore the default patient location list.
 Click the “Add” button to add a location in the list.
BeneVision CMS Operator‟s Manual
12-19
12.2.8.9 Auto Shrink Database (CentralStation Only)
Auto shrink database provides the ability to clear up the invalid data in the database and
release storage space. The system requires database shrinking daily. The default time of auto
database shrink is set to zero hour (00:00:00). You can set it to another desired time to suit
your needs.
To set the auto shrink database:
1.
Click the “Auto Shrink Database” button.
2.
Input the preset time for auto database shrink.
3.
Click “OK”.
12.2.8.10 Paging Settings (CentralStation Only)
 Paging Delay: Select it to set the paging delay time. The default setting is 10 seconds.
 Paging Demographics: Select it to set the degmographic data type sent to the pager. The
options include Bed No., Bed No. + Last Name, or Bed No. + Patient ID. The default
setting is Bed No.
 Paging switch: Select it to switch on/off the paging function. The default setting is On.
 Paging Password Protection: Select it to switch on/off the password requirement to enter
the paging window. The default is On.
12-20
BeneVision CMS Operator‟s Manual
12.3 Communication Settings
In the Communication Settings screen, you can set the current CentralStation‟s
communication with bedside devices, monitoring network, other CentralStations or
eGateway.
To access the Communication Settings menu, select the “Others” tab, and then the
“Communication Settings” button.
NOTE

Settings in the "Communication Settings" menu should not be changed, except
by trained Service Personnel.
12.3.1 Network Setup
Central Monitoring Network Settings
To set up the communication between a CMS and the master server, you need set the
following:
 Master Server IP Address: Enter the IP address of a CentralStation which is used as the
master server.
 Local IP address: In the drop-down list, select current CMS‟ IP address which is for
communication between the CentralStation and external systems, such as Gateway,
WorkStation, ViewStation, emote CentralStations.
Bedside Monitoring Network Settings (CentralStation Only)
To set up the communication between a CentralStation with the bedside devices, and to set
data sending mode, you need set the following:
 IP Address: In the drop-down list, select the IP address of the CentralStation network
adapter which is for internal communication between the CentralStation and beside
monitors.
 CMS Sending Broadcast Data: This function is used when you view telemetry data on the
bedside monitor. For the bedside monitor which only supports broadcast mode, you must
select the check box before “CMS Sending Broadcast Data” to use this function.
Multicast Setup
You can set up the multicast IP address and TTL value used for the following multicast
communications:
 Between CentralStation and the bedside device.
BeneVision CMS Operator‟s Manual
12-21
 Betweeen CentralStations.
 From CentralStation to WorkStation, ViewStation and CMS Viewer.
12.3.2 CentralStation Authorization (CentralStation Only)
Each CentralStation can be configured to specify the following access types of WorkStation,
ViewStation and CMS Viewer:
 Full Control: The WorkStation, ViewStation and CMS Viewer, based on their
corresponding read-write functions, are given full controls on this CentralStation.
 Read Only: The WorkStation, ViewStation and CMS Viewer can view this CentralStation.
 Off : The WorkStation, ViewStation and CMS Viewer cannot access this CentralStation.
Access to the CentralStation can be password protected by selecting the check box before
“Requires password to access this CentralStation”.
 When you select it for the first time, a password setting dialog will display.
 When you select it at other times, a “Modify Password” button will display. Select this
button to change the password.
12.3.3 Bed Authorization (CentralStation Only)
By selecting the checkbox before the monitor name, you can authorize the corresponding bed
on the current CentralStation to be viewed by Gateway/eGateway, CMS Viewer, another
CentralStation, WorkStation or ViewStation.
Refresh
You can update the list by clicking the “Refresh” button.
12-22
BeneVision CMS Operator‟s Manual
12.3.4 CentralStation Connection
There may be multiple CentralStations in the BeneVision monitoring network. These
CentralStations are listed in the CentralStation Connection screen with their names, IP
addresses, and connected statuses. If a CentralStation is connected, your current station
(CentralStation, WorkStation or ViewStation) has authorized access to this CentralStation.
Refer to 12.3.2 CentralStation Authorization (CentralStation Only) for the access type.
To connect a CentralStation:
1.
Select a CentralStation (except the current CentralStation) in the list.
2.
Select “Connect” button. If access to the selected CentralStation requires a password, a
password dialog box will display.
3.
Enter the required password. If the CentralStation is connected, the “Connect Status” for
the selected CentralStation displays as “Connected”.
Refresh
You can update the list by clicking the “Refresh” button.
12.3.5 Gateway Communication Setting (CentralStation Only)
The CentralStation can be configured with Gateway or eGateway to communicate with other
hospital systems.
NOTE

Settings in the “Gateway Communication Setting” tab should not be changed,
except by trained Service Personnel.
Gateway
When the CMS is configured with Gateway, the Gateway communication setting menu
provides seven tabs which are Networking Status, Network Setup, Authorization Setup,
Results Service, ADT Service, Comm. View, and Log View. For more information about the
functions, refer to Mindray Patient Data Share Solution Guide.
BeneVision CMS Operator‟s Manual
12-23
eGateway
You can configure the settings when the CentralStation communicates with the eGateway.
Transmit Data to eGateway
The options are “Enable” and “Disable”.
 When “Enable”is selected, the CentralStation data can be sent to the eGateway.
 When “Disable” is selected, the CentralStation data cannot be sent to the eGateway. All
items in “Gateway Communication Settings”, “ADT Query Setup” and “Data Export
Setup” are grey, and the CentralStation does not communicate with eGateway.
Gateway Communication Settings
You can set the CentralStation‟s communication mode with the eGateway:
 If “Multicast” is selected, the CentralStation communicates with eGateway in multicast
mode.
 If “Unicast” is selected, the CentralStation communicates with the specified eGateway in
unicast mode. “IP Address” will be the eGateway address, and the “Port” setting will be
consistent with that set in eGateway.
ADT Query Setup
When “ADT Query” is set to “Enable”, the “IP Address” and “Port” can be edited. “IP
Address” will be the eGateway address, and the “Port” setting will be consistent with that set
in eGateway.
NOTE

The "Obtain Patient Information" button is available on the patient management
screen only when“ADT Query”is set to “Enable”.
Data Export Setup
 Export Waveform Data: When configured to “Enable”, the button “Export to EMR” will
be displayed on the “Full Disclosure” (full size waveform view) and “Event Review”
sheets. The waveform or event can then be exported to other systems. When configured to
“Disable”, the waveform or event cannot be exported to other systems.
 Export 12-Lead ECG Report: When configured to “Enable”, the CentralStation will
receive the 12-lead ECG analysis result from the bedside monitor. The CentralStation will
then automatically generate a 12-lead ECG report, and send the report to other systems.
When configured to “Disable”, the report will not be generated.
12-24
BeneVision CMS Operator‟s Manual
 Input multicast IP address and port. “IP Address” will be the eGateway address, and the
“Port ” setting will be consistent with that set in eGateway.
The sampling characteristics of ECG waveforms are:
 Sampling frequency: export in full disclosure and event review:80 Hz; export in 12 lead
analysis review: 256 Hz
 Sampling amplitude resolution: 19.5313 uV/LSB
 Significant bits: 8 bits
BeneVision CMS Operator‟s Manual
12-25
FOR YOUR NOTES
12-26
BeneVision CMS Operator‟s Manual
13 Paging
13.1 Overview
The CentralStation has integrated a Paging interface using protocol TAP1.8. The Paging
acquires patient physiological alarms data from the bedside or the telemetry, and relays it to
the clinician-worn pager.
WARNING

The CentralStation provides a paging interface to allow a third-party paging
system to be connected. The third-party paging system may not provide visual or
auditory alarm indicators, and a delay within the third-party paging system may
occur. Therefore, do not rely on the third-party paging system only. Also pay
close attention to the BeneVision Central Monitoring System or monitoring
devices.
NOTE

You can set which alarms of an individual patient are sent to the pager. Refer to
8.4.2 Alarm Setup Window.
13.2 Accessing Paging Window
To access the paging window:
1.
Select the “Paging” button in the system button area. If a password is required, the
“Enter Password” dialog box will pop up.
2.
Enter the required password.
NOTE

Paging can be password protected. Refer to 12.2.8.10 Paging Settings for
enabling/disabling the password requirement.
BeneVision CMS Operator‟s Manual
13-1
13.3 Basic Operations
13.3.1 Adding a Pager
To add a pager:
1.
Select the “Pager Assignment” tab.
2.
Select the “Add” button. The “Pager Details” dialog box will pop up.
3.
Select the “Pager Number” field, and enter the pager number.
4.
Select the “Pager Assignment” field, and enter the name of the person who will be
responsible for the pager or some other identifying information.
5.
Select “Ok”. The pager with number and assignment will display in the pager list.
NOTE

Pager numbers and assignments must be unique.
13.3.2 Assigning an Existing Bed to a Pager
To assign an existing bed to a pager:
1.
Select the “Pager Assignment” tab.
2.
From the pager list, select a pager.
3.
From the bed list, select a bed, and then select the “Assign” button. The assigned bed
will appear under the pager in the pager list.
NOTE

A bed can be assigned to more than one pager.
13.3.3 Assigning a New Bed to a Pager
If a bed currently is not available in the bed list, you can add and assign the bed to a pager:
1. Select the “Pager Assignment” tab.
13-2
2.
From the pager list, select a pager.
3.
Select the “Add and Assign” button. A dialog box will pop up.
4.
Enter the bed No.
5.
Select “Ok”.
BeneVision CMS Operator‟s Manual
NOTE

A bed can be assigned to more than one pager.
13.3.4 Removing a Bed Assignment
To remove an existing bed assignment from a pager:
1.
Select the “Pager Assignment” tab.
2.
From the pager list, select the assigned bed under a pager.
3.
Select the “Unassign” button.
13.3.5 Editing a Pager
To edit an existing pager number or pager assignment:
1.
Select the “Pager Assignment” tab.
2.
From the pager list, select the pager to be edited.
3.
Select the “Edit” button. The “Pager Details” dialog box will pop up.
4.
Edit the pager information.
5.
Select “Ok”.
13.3.6 Removing a Pager
To remove a pager:
1.
Select the “Pager Assignment” tab.
2.
From the pager list, select the pager to be removed.
3.
Select the “Delete” button. A prompt “Are you sure you want to delete this pager and all
its assignments?” is displayed.
4.
Select “Ok”.
BeneVision CMS Operator‟s Manual
13-3
13.4 Resending a Failed Page
If an attempt to send a page was unsuccessful, the page will be added to the Failed Page tab
sheet. The “Failed Page” screen contains a list of failed pages. The failed pages are shown
chronologically in descending order.
To resend a failed page:
1.
Select the “Failed Page” tab.
2.
Select a failed page from the list box.
3.
Select the “Resend” button. The failed page is resent and the row is removed from the
list box if the page was successfully resent. If the page was not successfully resent, a
new row will be added to the top of the Failed Page list with an updated date and time.
If the failed pages are not necessary, you can select the “Delete” button to delete an
individual page, or select “Delete All” to delete all the pages on the tab sheet.
13-4
BeneVision CMS Operator‟s Manual
14 Remote CMS
14.1 Overview
In the event that there are multiple CentralStations in a LAN, the CentralStation can view a
single patient connected to the target CentralStation in the LAN through the Remote CMS
window.
Through the Remote CMS window, you can only view the target monitoring device rather
than setting and controlling the target CentralStation or monitoring device.
WARNING

In the Remote CMS window, no audio alarms are provided for the viewed
CentralStation.
NOTE

One CentralStation can be viewed by a maximum of 16 CMS Viewers or other
CentralStations simultaneously.
BeneVision CMS Operator‟s Manual
14-1
14.2 Remote CMS Viewbed Window
Click the “Remote CMS” button at the bottom of the screen and enter the Remote CMS
window. Then select the “ViewBed” tab. The ViewBed screen is shown as below.
2
1
3
4
5
6
7
8
1. Beds list
4. Alarm icon area
2. Patient information area
5. Technical alarm area
7. Waveform area
8. Parameter area
3. Physiological alarm area
6. Button area
Figure 14-1 Remote CMS Viewbed Screen
14.2.1 Beds List
The beds list displays the information about all CentralStations and networked bedside
devices (target bed) in the same network segment of a LAN.
When the “Remote CMS” screen is accessed, the CentralStation will automatically list other
CentralStations which can be operated remotely. Only when the CentralStations‟ IP addresses
are added in the “CentralStation Connection” menu, will the names of the corresponding
CentralStations be automatically displayed in the list.
In the beds list, the first-level nodes are the unit names of the CentralStations; the secondlevel nodes are the monitors connected to the CentralStations. Generally, the name of the
second-level node is department, bed number and patient name.
You can select the target monitoring device to be viewed by selecting the radio button before
the second-level node, or the monitor.
The background color indicates the status of the target monitoring device.
14-2
BeneVision CMS Operator‟s Manual
 White: indicates no alarm on the target monitoring device.
 Red: indicates a high level alarm, nurse call or event on the target monitoring device.
 Yellow: indicates a medium level alarm on the target monitoring device.
 Cyan: indicates a low level alarm on the target monitoring device.
 Grey: indicates that the target monitoring device is in standby status.
 Light Grey: indicates that the target monitoring device is offline.
14.2.2 Physiological Alarm Area
This area displays physiological alarm messages and relevant text coming from the viewed
target monitor. The display rule is the same as that in the physiological alarm area of the
patient window. Please refer to 6.3.3.5 Physiological Alarm Area.
Different background colors are used to indicate the alarm priorities.
 Red: indicates a high level alarm on the target monitoring device.
 Yellow: indicates a medium level alarm on the target monitoring device.
 Cyan: indicates a low level alarm on the target monitoring device.
14.2.3 Technical Alarm Area
This area displays technical alarm messages or prompt messages circularly coming from the
viewed target monitoring device. The display rule is the same as that in the technical alarm of
the patient window. Please refer to 6.3.3.4 Technical Alarm Area.
14.2.4 Alarm Icon Area
This area displays icons for alarm pause
, alarm off
, and alarm reset
. Please
refer to 6.3.3.3Alarm Icon Area.
NOTE

In the Remote CMS window, only the alarm messages coming from the target
monitoring device will be displayed.
14.2.5 Button Area
Click this button to open the “Filtering Setup” menu, from which you can select your desired
waves and parameters. The waveform and parameter areas will then display the
corresponding waveforms and parameters.
BeneVision CMS Operator‟s Manual
14-3
14.2.6 Waveform Area
This area displays the waveforms on the target monitoring device.
14.2.7 Parameter Area
This area displays the parameters on the target monitoring device. Each block displays the
parameters from the same parameter module.
14.3 Remote CMS Review
In the Remote CMS window, there is “Full Disclosure” tab, “Trend Review” tab, “Event
Review” tab, “ST Review” tab, “12-lead Review” tab and “C.O. Review” tab. Select a tab to
access the corresponding review sheet. The function of Remote CMS review is similar to that
of local CMS online review. Please refer to 9.1 Online Review.
14.4 Network Setup and Authorization
If your CentralStation needs to implement the Remote CMS function on another
CentralStation, the following configurations are required:
 In the “Communication Setting” menu of your CentralStation, connect the CentralStation
to be viewed in the “CentralStation Connection” tab sheet. Refer to 12.3.4 CentralStation
Connection for details.
 In the “Communication Setting” menu of another CentralStation, authorize itself and its
beds viewed by the other CentralStation. Refer to 12.3.2 CentralStation Authorization
(CentralStation Only) for central authorization, and 12.3.3 Bed Authorization
(CentralStation Only) for bed authorization.
14-4
BeneVision CMS Operator‟s Manual
15 Database Backup and Recovery
15.1 Overview
The CentralStation provides database backup and recovery.
The CentralStation will shut off automatically during database backup and recovery.
You can start database backup and recovery by operating the CentralStation or the Windows
operating system, or when you fail to log into the database.
By operating the CentralStation
Enter the “Admin Setup” menu; select “Other” to open a tab sheet.
Click the “Database Backup and Recovery” button and a message box will pop up. Select
“Yes”, the CentralStation will automatically shut off and start database backup and recovery.
NOTE

Take care to perform database backup and recovery. This will automatically shut
off the CentralStation.
When the CentralStation fails to log into the database
The CentralStation will automatically log into the database when it starts. If it fails to log into
the database, a message box will pop up. Click the “Restart” button to restart the
CentralStation; select the “Recover” button to backup and recover the database.
By operating the Windows operating system
Click the “Start” button of the Windows operating system; select “Programs” and then select
“Database Backup and Recovery” to run the database backup and recovery program.
BeneVision CMS Operator‟s Manual
15-1
15.2 Backup Database
15.2.1 Select Operation Type
When you run the “Database Backup and Recovery” program, a dialog box will pop up for
you to select the operation type. Select “Backup Database”.
15.2.2 Select Backup Path
You can backup the database on the local hard disk or on a USB disk.
Select a path from the drop-down list. The available hard disk partitions are listed
automatically and a directory in which the backup file is stored is created automatically.
NOTE

Do not modify the directory of the backup file. It is specified by the system.
The directory is named YYYYMMDDhhmmbak, in which YYYY refers to the year, MM
refers to the month. DD refers to the date, hh refers to the hour and mm refers to the minute.
15.2.3 Backup Database
After selecting the backup path, click the “Next” button and a dialog box will appear. Click
the “Start” button to start the database backup.
If the database backup times out or an abnormal condition occurs during the database backup,
a message will be presented.
If the backup database is stored on the local hard disk, the old backup file will be deleted
automatically so that only one backup file is stored on the local hard disk. If the backup is
stored on a USB disk, the old one will not be deleted.
15-2
BeneVision CMS Operator‟s Manual
15.3 Recover Database
CAUTION

The recovered database will overwrite the current one. Make sure you backup
the current database before carrying out database recovery.
NOTE

If the CentralStation cannot start normally due to a database error resulting an
abnormal shutoff or improper operation, recover the database.
15.3.1 Select Operation Type
After the “Database Backup and Recovery” program starts up, a dialog box will appear.
Select “Recover Database”.
15.3.2 Select Path
You can recover the database from the local hard disk or from a USB disk.
If you select the local hard disk, the system will search for the correct backup database for
recovery on the local hard disk.
If you select the USB mobile medium, click the
icon and select the backup file for
recovery.
15.3.3 Recover Database
After selecting the correct path for the database recovery, select the “Next” button to enter a
dialog box. Then click the “Start” button to start database recovery.
If the database recovery times out or an abnormal condition occurs during the database
recovery, a message will be presented.
BeneVision CMS Operator‟s Manual
15-3
15.4 Rebuild Database
After the “Database Backup and Recovery” program starts up, a dialog box will appear.
Select “Rebuild Database”.
NOTE

All the data in the current database will be deleted during rebuilding of the
database.

All alarm settings previously saved will be lost and will have to be manually
restored.
15.5 Shrink Database
After the “Database Backup and Recovery” program starts up, the dialog box will appear.
Select “Shrink Database”.
If an abnormal condition occurs during database shrink, a message will be presented.
15.6 Exit Database Backup and Recovery
When you exit the “Database Backup and Recovery” program, the CentralStation will start
automatically.
15-4
BeneVision CMS Operator‟s Manual
16 System Help
16.1 Overview
The CMS features a webpage-like on-line help to assist in obtaining a better understanding of
the system. Click the “Help” menu to enter the help screen.
There are three icons on the top left of the Help screen:

: Page down

: Page up

: Return to the screen as shown in the above figure

: Display copyright information, including system software version, system software
and database copyright information, etc.
NOTE

The help information on the CMS is not only about the system itself, but also on a
number of concepts and operations related to bedside monitors.
You can enter the corresponding help information by selecting any of the following three
links:
 Introduction: Brief introduction to the CMS and its configuration.
 Operation Introduction: Introduction to various operations of the CMS, such as multi-bed
and viewbed observation.
 Bio Essentials: Introduction to the monitoring functions of each parameter module, such
as ECG, SpO2, etc.
BeneVision CMS Operator‟s Manual
16-1
FOR YOUR NOTES
16-2
BeneVision CMS Operator‟s Manual
A Technical Specifications
A.1 Requirements
The computer of the CMS should be highly reliable and stable. The recommended
configurations are as follows:
Components
Requirements
System
Meet the IEC60950 requirements defined for ITE equipment, and comply
with CE low voltage directives (LVD) and EMC directives.
CentralStation:
4 cores and 2.9 GHz minimum
4GB minimum memory
500 GB minimum hard disk, support data redundancy by dual hard disks
100M (minimum) self-adapting, Ethernet 802.3
Two or more USB ports
One or more serial ports
Host
WorkStation and ViewStation:
2 cores and 2.0 GHz mininum
2GB minimum memory
280 GB minimum hard disk
100M (minimum) self-adapting, Ethernet 802.3
two or more USB ports
One or more serial ports
Display
19" LCD minimum, 1280×1024, length: width 4:3 or 5:4, with CE marking.
Operating
System
Support Windows® 7 Professional Embedded SP1 (32 bits)
Antivirus
Support Solidcore S3 Control
Graphic card
Support dual or multiple displays.
Mouse
With CE marking.
Keyboard
With CE marking.
Recorder
Mindray thermal array, serial port.
Printer
Supporting A4 and Letter paper.
Speaker
Built in the computer or the display. Give alarm tones (45 to 85 dB), alarm
tones comply with IEC 60601-1-8.
NOTE

The configuration above is for reference only.
BeneVision CMS Operator‟s Manual
A-1
A.2 Recorder
Size
210×100×100 mm
Weight
1 kg
Type
Thermal recorder
Record rate:
25 mm/s, 50 mm/s
Accuracy: ±10%
Interface
RS232 interface
Width of the recorder paper
50 mm
A.3 Audio Signals
Alarm tone
600 Hz, ISO pattern
Self-test tone
650 Hz, a short beep
Alarm volume adjusting tone
650 Hz, a short beep
Event tone
A long tinkle
Nurse call tone
Three beeps
A.4 Wired Network
Network structure
Ethernet 802.3
Transmission rate
10/100 Mbps
Network interface
RJ45
Max alarm time delay
≤ 3s
A.5 Review
Dynamic short trend
4 hours
Trend review
240 hours
Full disclosure
240 hours of full-disclosure waveforms and compressed
waveforms
C.O. review
720 measurements
NIBP review
Most recent 240 hours of NIBP measurements
Event review
720 events, including the parameter name and 16s waveform
respectively before and after the alarm is triggered
Historic review
up to 20,000 discharged patients‟ data
12-lead Review
720 12-lead analysis results, 12 analysis waveforms for each
analysis result
A-2
BeneVision CMS Operator‟s Manual
ST review
Most recent 240 hours of ST segments
A.6 Calculation
Drug calculation
75 calculations for single patient
Hemodynamics calculation
100 calculations for single patient
Oxygenation calculation
100 calculations for single patient
Ventilation calculation
100 calculations for single patient
Renal calculation
100 calculations for single patient
A.7 Save As
File format
HTML
Storage media
mobile hard disk, flash drive
Contents
Graphic/table, full disclosure, C.O. measurements, event review,
drug calculations, hemodynamics calculations, oxygenation
calculations, ventilation calculations, renal calculations, 12-lead
Review and DSA graph
A.8 Display
Sweep speed
6.25 mm/s, 12.5 mm/s, 25 mm/s, 50 mm/s
Accuracy: ±10%
A.9 Print
Print paper
Sweep speed
Contents
A4 or Letter
12.5 mm/s, 25 mm/s, 50 mm/s
Accuracy: ±10%
Patient information, Graphic/table, full disclosure, waveform
segment report, C.O. measurement, events, drug calculation,
hemodynamic calculations, oxygenation calculations, ventilation
calculations, renal calculations, 12-lead Review, ST waveforms,
real-time report, 12-lead ECG report, multi-lead ECG report,
Arrh statistics result, EEG report, ICG report, CCO report,
SvO2/ScvO2 report, alarm settings report, real-time alarm report,
QT report, paging assignment report.
BeneVision CMS Operator‟s Manual
A-3
A.10 Record
Contents
Patient information, full disclosure, C.O. measurement, events,
drug calculation, hemodynamics calculations, oxygenation
calculations, ventilation calculations, renal calculations, realtime waveform recoding, real-time alarm recording, 12-lead
Review, ST review, ICG hemodynamic parameter, CCO
hemodynamic parameter, SvO2/ScvO2 oxygenation parameters
A.11 Data Export
Data format
Standard xml file 1
Protocol
Windows CIFS 2
Frequency:
ECG waveform sampling
characteristics
Amplitude
resolution:
Significant bits:
Export in full disclosure and event review:
80 Hz
Export in 12 lead analysis review: 256 Hz
19.5313 uV/LSB
8 bits
1
: For more information, please contact Mindray.
: The CIFS protocol is from Windows Operating System.
2
A-4
BeneVision CMS Operator‟s Manual
B CMS Alarms
The CMS technical alarms displayed in the system alarm area on the upper screen are
shown in the table below.
Alarms
Level
Cause or solution
Printer is out of toner
Printer is offline
Low
Low
Printer paper is jammed
Low
Printer is out of paper
Opening Recorder Port Failed
Recorder Paper Jam
Recorder Out of Paper
Recorder Out of Alignment
Recorder is Too Hot
Low
Med
Low
Low
Low
Low
Recorder Not Available
Recorder S. Communication
Error
Network is disconnected. Please
check.
Network is not configured or
disabled. Please check.
No bed is online. Please check
network connection.
Med
Med
Install the toner.
Connection between printer and computer may
have a problem. Check the connection.
Change the paper and then restart the printer and
printing task.
Load paper and then restart the printing task.
Restart the recorder.
Reload the paper.
Reload the paper.
Adjust the recorder head.
The recorder has worked for a long time. Wait
until it cools down.
Restart the recorder.
Check the connection cable of recorder serial
port.
Check the network.
Database service is abnormal.
Please restart CMS or contact
the service representative.
The patient storage space is
nearly full. Please delete some
discharged patients.
High
Communication lost
Low
Pager communication lost
Low
High
High
High
Med
BeneVision CMS Operator‟s Manual
Check the network configuration of the
CentralStation.
This alarm is only available on the
CentralStation.
Check whether the patient monitor is connected
to the network.
Database service has an error. Restart the
CentralStation to restore database service or
contact the service personnel.
This alarm is only available on the
CentralStation.
The discharged patient storage space is nearly
full. Please delete some discharged patients.
Check the connection between WorkStation/
ViewStation and the CentralStation.
Check the paging network.
B-1
The CentralStation alarms displayed in the patient window‟s technical alarm area are shown
in the table below.
Alarms
Level
Cause and solution
Offline
Low
The bedside monitor is disconnected from the
CentralStation network. Please check.
B-2
BeneVision CMS Operator‟s Manual
C Units, Symbols, Terms and Formulas
C.1 Units
BPM
beats per minute
℃
cc
cm
cmH2O
dB
centigrade
℉
g
GB
GTT
hr
hPa
Hz
"
k
kg
kPa
l
lb
m
M
MB
mbar
MHz
mcg
mEq
mg
min
ml
mm
mmHg
ms
RPM
s
V
W
Fahrenheit
cubic centimeter
centimeter
centimeter of water
decibel
gram
giga bytes
gutta
hour
hectopascal
hertz
inch
kilo
kilogram
kilopascal
liter
pound
meter, minute
mega
mega bytes
millibar
mega hertz
micrograms
milli-equivalents
milligrams
minute
milliliter
millimeters
millimeters of mercury
millisecond
respiration per minute
second
volt
watt
BeneVision CMS Operator‟s Manual
C-1
C.2 Symbols
%
&
/
~
+
<
=
>
±
×
minus
percent
and
per, divide, or
to
Plus
Less than
Equal to
Greater than
Plus or minus
Multiply
C.3 Abbreviations
ABBREVIATION
DEFINITIONS
air cyl.
AC
ADT
AgAwRR
Air Flow
AG
ART
ATMP
AP MAP
AUX
AVF
AVL
AVR
AWRR
BC
BIS
CCI
Cdyn
CE
CFI
CH
C.I.
C.O.
CCO
CO2
Air cylinder pressure
Alternating current
Admission\Discharge\Transfer
Anaesthesia gas air-way respiration rate
Air flow
Anesthesia gas
Arterial
Atmospheric pressure
Mean artery pressure
Auxiliary
Left foot augmented lead
Left arm augmented lead
Right arm augmented lead
Air way respiratory rate
Burst count
Bispectral index
Continuous cardiac index
Dynamic compliance
Conformité Européenne
Cardiac function index
Channel
Cardiac index
Cardiac output
Continuous cardiac output
Carbon dioxide
C-2
BeneVision CMS Operator‟s Manual
ABBREVIATION
DEFINITIONS
Compl
CPI
CPO
CPU
CRT
Cr
Cstat
CVP
DES
D, DIA
dPmx
DO2
DO2I
ECG
EDV
EE
EEC
EMC
EMG
EMR
ENF
Et
EtAA
EtAA 2nd
EtDes
EtSev
EtEnf
EtIso
EtHal
EtCO2
EtN2O
EtO2
EVLW
ELWI
Exp%
Exp. Flow
Exp. MAC
f
fapnea
fCMV
Compliance
Cardiac power index
Cardiac power output
Central processing unit
Cathode ray tube
Creatinine
Static compliance
Central venous pressure
Desflurane
Diastolic
Left ventricular contractility
Oxygen delivery
Oxygen delivery index
Electrocardiograph
End-diastolic volume
Energy expenditure
European Economic Community
Electromagnetic compatibility
Electromyograph
Electronic Medical Record
Enflurane
End-tidal
End-tidal anesthetic agent
2nd Exp. Agent
End-tidal desoflurane
End-tidal sevoflurane
End-tidal enflurane
End-tidal isolurane
End-tidal haloflurane
End-tidal carbon dioxide
End-tidal nitrous oxide
End-tidal oxygen
Extravascular lung water
Extravascular lung water index
Inspiration termination level
Expiratory flow
Expired minimum alveolar concentration
Breath rate
Breath rate for apnea ventilation
CMV frequency
FEV1.0%
FG
Fi
FiAA
First second forced expiratory volume ratio
Fresh gas flow
Fraction of inspired
Inspired anesthetic agent
BeneVision CMS Operator‟s Manual
C-3
ABBREVIATION
DEFINITIONS
FiAA 2nd
FiCO2
FiN2O
FiO2
FiDes
FiSev
FiEnf
FiIso
FiHal
fmand
FRC
FreqMIN
fSIMV
fsigh
fspn
ftot
F-Trigger
FV
GEDV
GEDI
GEF
HAL
Hb
Hct
HR
IBP
IBW
ICP
ICU
ID
I:E
IEC
Insp.Flow
Insp. MAC
2nd Insp. Agent
Fraction of inspired carbon oxygen
Fraction of inspired nitrous oxide
Fraction of inspired oxygen
Inspired desoflurane
Inspired sevoflurane
Inspired enflurane
Inspired isoflurane
Inspired haloflurane
Mandatory breathing frequency
Fractional residual capacity
Minimum breath frequency
Frequency of SIMV
Sigh rate
Spontaneous breathing frequency
Total breath rate
Inspiratory trigger level (flow trigger)
Flow-volume
Global end diastolic volume
Global end diastolic volume index
Global ejection fraction
Halothane
Hemoglobin
Hematocrit
Heart Rate
Invasive brood pressure
Ideal body weight
Intracranial pressure
Intensive care unit
Identification
Inspiratory time: Expiratory time ratio
International Electrotechnical Commission
Inspiration flow
Inspired minimum alveolar concentration
△int.PEEP
Ins, INS
InsCO2
IP
ISO
ITBV
ITBI
ITE
LAP
LCD
Intermittent PEEP
C-4
Inspired minimum
Inspired minimum carbon dioxide
Internet Protocol
Isoflurane
Intrathoracic blood volume
Intrathoracic blood volume index
Information technology equipment
Left artrial pressure
Liquid crystal display
BeneVision CMS Operator‟s Manual
ABBREVIATION
DEFINITIONS
LVD
M, Mean
Mac, MAC
%MinVol
MV
MVe
MVLEAK
N2O
N2O cyl.
N2O Flow
N/A
NIBP
NIF
O2
Low voltage directive
Mean pressure
Minimal alveolar concentration
Percentage of minute volume to be delivered
Minute volume
Expiratory minute volume
Leakage minute volume
Nitrous oxide
N2O cylinder pressure
N2O flow
Not applied
Noninvasive blood pressure
Negative inspiratory force
Oxygen
ΔO2
O2CI
O2 cyl.
O2 cyl.2nd
O2 Flow
oxyCRG
P0.1
PA
PA MAP
Pair
PaO2
PaCO2
Papnea
Paux Mean
Paux Min
Paux Peak
pArt-M
pArt-D
pArt-S
PC
pCVP
PeCO2
PEEP
PEEPi
PEEPtot
PEF
Phigh
PIF
Pinsp
PIP
Difference between inspiratory and expiratory O2
Oxygen consumption index
Oxygen cylinder pressure
Secondary oxygen cylinder pressure
O2 flow
Oxygen Cardio-respirogram
100 ms occlusion pressure
Pulmonary artery
Mean pulmonary artery pressure
Air supply pressure
Arterial oxygen level
Arterial carbon dioxide level
Apnea pressure
Mean auxiliary pressure
Minimum auxiliary pressure
Peak auxiliary pressure
Mean artery pressure
Diastolic artery pressure
Systolic artery pressure
Personal computer
Central venous pressure
Mixed expire CO2 pressure
Positive end-expiratory pressure
Intrinsic positive end-expiratory pressure
Total PEEP
Peak expiratory flow
Upper pressure level
Peak inspiratory flow
Pressure control level of inspiration
Peak inspiratory pressure
BeneVision CMS Operator‟s Manual
C-5
ABBREVIATION
DEFINITIONS
PLETH
Plimit
Plow
Pmax
Pmean
Posm
Ppeak
Pplat
PPV
PR
PTP
PS/2
Psupp
Plethysmogram
Pressure limit level
Lower pressure level
Maximum airway pressure
Mean pressure
Plasma Osmolality
Peak pressure
Plateau pressure
Pulse Pressure Variation
Pulse rate
Pressure time product
Personal System/2
Pressure support level
Inspiratory trigger
level(pressure trigger)
Premature ventricular contraction
Pulmonary vascular permeability index
Ramp
Right atrial pressure
Airway resistance
Expiratory time constant
Inspiratory time constant
Expiratory resistance
Respiration
Inspiratory resistance
Respiratory quotient
Respiration rate
Rapid shallow breathing index
Arterial oxygen saturation
Spectral edge frequency
Serum sodium
Stroke volume
Stroke volume index
Mixed venous oxygen saturation
Central venous oxygen saturation
Systemic vascular resistance
Systemic vascular resistance index
Stroke volume variation
Sevoflurane
Arterial oxygen saturation from pulse oximetry
Signal quality index
Suppression ratio
Systole/systolic
Temperature of blood
P-Trigger
PVC
PVPI
Ramp
RAP
RAW
RCexp
RCinsp
Re
RESP
Ri
RQ
RR
RSBI
SaO2
SEF
SerNa
SV
SVI
SvO2
ScvO2
SVR
SVRI
SVV
SEV
SpO2
SQI
SR
S, SYS
TB
C-6
BeneVision CMS Operator‟s Manual
ABBREVIATION
DEFINITIONS
TCP/IP
tcpCO2
tcpO2
TEMP
Texp
Thigh
TI
Ti max
Tinsp
Tip
TIP:TI
Tlow
TP
TRC
Trig Window
Trigger
Trise
Tslope
TV
Ucr
Uosm
UPS
URK
URNa
USB
V
VAC
VCO2
Ver
VO2
VO2/kg
VO2/m2
VO2I
VT
VTapnea
VTe/TVe
VTe spn
VTi/TVi
VTsigh
WOB
WOBimp
Telecommunication Control Protocol/Internet Protocol
Transcutaneous carbon dioxide partial pressures
Transcutaneous oxygen partial pressures
Temperature
Expiratory time
Time for the upper pressure level
Temperature of Injectate
maximum inspiration time
Time of inspiration
Inspiratory pause time
Percentage of inspiratory plateau time in inspiratory time
Time for the lower pressure level
Total power
Tube resistance compensation
Trigger window
Trigger sensitivity
Rise time
Time for the pressure to rise to target pressure
Tidal volume
Urine creatinine
Urine osmolality
Uninterruptible power supply
Urine potassium
Urine sodium
Universal serial bus
Precordial lead
Volts alternating current
CO2 production
version
Oxygen consumption
Oxygen consumption per body weight
Oxygen consumption per body surface area
Oxygen Consumption Index
Tidal volume
Apnea tidal volume
Expiratory tidal volume
Spontaneous breathed minute volume
Inspiratory tidal volume
Sigh tidal volume
Work of breathing
Imposed work of breathing
BeneVision CMS Operator‟s Manual
C-7
C.4 Formulas
Drug Calculations
Abbreviation and Unit
Description
Formula
Concentration
AMOUNT / Liquid Volume
DOSE/hr
Infusion Rate × Conc.
DOSE/min
(DOSE/hr)/ 60
DOSE/kg/hr
(DOSE/hr) / kg
DOSE/kg/min
(DOSE/hr) / kg / 60
Drip Rate
DURATION
(Infusion Rate × Drop Size)/ 60
Liquid Volume / Rate
Description
Formula
BSA (m )
CI (L/min/m2)
SV (ml)
SVI (ml/m2)
SVR (DS/cm5)
Body Surface Area
Cardiac Index
Stroke Volume
Stroke Volume Index
Wt 0.425 × Ht 0.725 × 0.007184
C.O. / BSA
C.O. / HR × 1000
SV/ BSA
Systemic
Resistance
Vascular
79.96 ×(AP MAP - CVP)/
C.O.
SVRI (DS m2/cm5)
Systemic
Resistance Index
Vascular
PVR (DS/cm5)
Pulmonary
Resistance
Vascular
PVRI (DS m2/cm5)
Pulmonary
Vascular
Resistance
Left Cardiac Work
Left Cardiac Work Index
Left Ventricular Stroke Work
Left Ventricular Stroke Work
Index
Right Cardiac Work
Right Cardiac Work Index
Right Ventricular Stroke
Work
Right Ventricular Stroke
Work Index
Ejection Fraction
Conc. (mcg/ml, mg/ml,
g/ml, units/ml, k units/ml,
m units/ml or mEq/ml)
DOSE/hr (mcg, mg, units,
k units, m units or mEq)
DOSE/min(mcg, mg, units,
k units, m units or mEq)
DOSE/kg/hr(mcg, mg,
units, k units, m units or
mEq)
DOSE/kg/min(mcg, mg,
units, k units, m units or
mEq)
Drip Rate (GTT/min)
Duration (hr)
Hemodynamic Calculations
Abbreviation and Unit
2
LCW (kg-m)
LCWI (kg–m/m2)
LVSW (g-m)
LVSWI (g-m/m2)
RCW (kg-m)
RCWI (kg-m/m2)
RVSW (g-m)
RVSWI (g-m/m2)
EF (%)
C-8
SVR × BSA
79.96 ×(PA MAP - PAWP)/
C.O.
PVR × BSA
0.0136 × AP MAP × C.O.
LCW / BSA
0.0136 × AP MAP× SV
LVSW / BSA
0.0136 × PA MAP × C.O.
RCW / BSA
0.0136 × PA MAP × SV
RVSW / BSA
100 × SV / EDV
BeneVision CMS Operator‟s Manual
Ventilation Calculations
Abbreviation and Unit
Description
Formula
PAO2 (mmHg)
Alveolar Oxygen Level
FiO2 / 100 ×(ATMP - 47)-
PaCO2 ×(FiO2 / 100 + (1-
FiO2 / 100) / RQ )
AaDO2 (mmHg)
Pa/FiO2 (mmHg)
a/AO2 (%)
MV (L/min)
Vd (ml)
Vd/Vt (%)
VA (L/min)
Alveolar-arterial Oxygen
Difference
Oxygenation Ratio
Arterial to Alveolar Oxygen
Ratio
Minute Volume
PAO2 - PaO2
100 × PaO2 / FiO2
100 × PaO2 / PAO2
(TV × RR)/ 1000
Volume of Physiological
Dead Space
Physiological Dead Space in
Percent of Tidal Volume
TV ×(1 - PeCO2 / PaCO2)
100 × Vd/TV
Alveolar Volume
(TV- Vd) × RR / 1000
Abbreviation and Unit
Description
Formula
URNaEx (mmol/24h)
URKEx (mmol/24h)
Na/K (%)
CNa (ml/24h)
Urine Sodium Excretion
Urine Potassium Excretion
Sodium Potassium Ratio
Clearance of Sodium
Clcr (ml/min)
Creatinine Clearance Rate
Urine × URNa / 1000
Urine × URK / 1000
100 × URNa / URK
URNa × Urine / SerNa
Ucr × Urine / Cr / (BSA / 1.73) /
1440
FENa (%)
Fractional
Sodium
Cosm (ml/min)
Osmolar Clearance
Uosm × Urine / Posm / 1440
CH2O (ml/h)
Free Water Clearance
Urine × (1-Uosm / Posm)/ 24
Renal Calculations
U/P osm
BUN/Cr
U/Cr
Excretion
of
Urine to plasma osmolality
ratio
Blood
Urea
Nitrogen
Creatinine Ratio
Urine-Serum
Creatinine
Ratio
100 ×(URNa × Cr ) / (SerNa ×
Ucr)
Uosm / Posm
1000 × BUN / Cr
Ucr / Cr
Oxygenation Calculations
Abbreviation and Unit
Description
O2ER (%)
DO2 (ml/min)
Calculated
Oxygen
Consumption
Arteriovenous
Oxygen
Content Difference
Oxygen Extraction Ratio
Oxygen Transportation
PAO2 (mmHg)
Alveolar Oxygen Level
VO2 calc (ml/min)
C(a-v)O2 (ml/L)
BeneVision CMS Operator‟s Manual
Formula
C(a-v)O2× C.O.
CaO2 - CvO2
100×C(a-v)O2/ CaO2
C.O. × CaO2
FiO2 / 100 ×(ATMP - 47)-
PaCO2 ×(FiO2 / 100 + (1-
FiO2 / 100) / RQ )
C-9
AaDO2 (mmHg)
Alveolar-arterial
Difference
CcO2 (ml/L)
Capillary Oxygen Content
Hb × 1.34 + 0.031 × PAO2
Qs/Qt (%)
Venous Admixture
100× [1.34 × Hb × (1-SaO2 /
100) + 0.031× (PAO2 -PaO2)] /
[1.34 × Hb × (1-SvO2 / 100) +
0.031× (PAO2 - PvO2 )]
C.O. calc (L/min)
Calculated Cardiac Output
VO2 / (CaO2 - CvO2 )
C-10
Oxygen
PAO2 - PaO2
BeneVision CMS Operator‟s Manual
D Anomaly
Anomaly Description
If the CentralStation is currently displaying an expand view (such as Device Integration
Expand View) of a patient with a T1 monitor, and that patient is transferred to another bed, if
the ViewBed screen is chosen within 5 seconds after the patient is monitored on the
destination bed, then the relevant expand view is not automatically displayed on the
destination bed.
NOTE


This issue can be corrected by selecting another bed, and then switching back to
the original bed.
This anomaly has been determined as cosmetic and minor nuisance issue, and
will not present a safety hazard to either operator or patient.
BeneVision CMS Operator‟s Manual
D-1
FOR YOUR NOTES
D-2
BeneVision CMS Operator‟s Manual
P/N: 046-007960-00 (1.0)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement