lid 050

lid 050
Service Procedure
INTRODUCTION
TASK FORCE TIPS’ AUTOMATIC: The nozzle you have purchased is your primary tool in the battle against fire. It has
been manufactured with great care to give you the finest performance possible. All components are of top quality and
extremely rugged. With occasional inspection and attention it will serve you for many years. This publication is intended
for those who prefer to perform service on their own equipment. Factory service is available, and repair time seldom
exceeds one day in our facility. Factory serviced nozzles are repaired by experienced workmen, fully tested and promptly
returned functioning to original specifications. Repair charges for non-warranty items are minimal. Task Force Tips
assumes no liability for damage to equipment or injury to personnel that is a result of user service.
GENERAL INFORMATION
THREADED JOINTS have been secured using Loctite brand thread locking adhesive #271. Disassembly requires a
minimal application of heat with a propane or oxyacetylene torch to break the bond. The threads should be heated to
approximately 450 degrees F. Excessive heat application will cause damage to adjacent seals and labels. Replacement
parts must be reinstalled using Loctite #271, or equivalent. Small vials of Loctite for field service are available; order part
# V5010, LOCTITE MINI DISPENSER.
LUBRICANTS: If parts are dissambled in an area where o-rings are present, re-assemble using DOW #44 High
Temperature Silicone Grease on all o-rings and surfaces that the o-rings contact.
LABEL REPLACEMENT: If labels become damaged, remove old labels with razor knife. Remove adhesive with acetone
or methyl ethyl ketone. Surface must be clean, dry and free from grease. Carefully apply new label.
ORDERING PARTS: Always specify the serial number of the nozzle when ordering parts. The number is found on the
raised rim of the SHAPER GUIDE [74]. Be sure to use complete DESCRIPTION and ORDER #, as printed on parts list. All
requests for couplings must specify thread size. Pricing information will be given at time of order.
COUPLING AND BASE SERVICE PROCEDURE
Tools Required:
1/8" Allen (hex) Wrench
Loctite #271 Thread Locking Adhesive
Torch, Oxyacetylene or propane
GENERAL: Occasional replacement of hose gaskets is recommended. Replace GASKET GRABBER [18] if severe
impact has caused damage. Coupling service kits which include all hardware and Loctite are available for either 1.5 or
2.5 inch couplings. Special configurations or model changes to a nozzle can be made by selecting the desired coupling
or base. Couplings with special or standard threads are interchangeable and may be exchanged on new nozzles. Please
specify desired threads when ordering.
COUPLING AND BLITZ BASE REMOVEL: All couplings and blitz bases are retained with a ball race, and set screw.
Heat, and then remove 1/4-28 SOCKET SET [5 or 16] screw from coupling using an 1/8" Allen wrench. Turn coupling so
that hole faces down, and rotate coupling back and forth to allow 3/16 STAINLESS STEEL BALLS [4 or 17] to drop out.
When all balls are out of the groove, the coupling can be removed. Remove GASKET GRABBER [18] debris screen from
the coupling. NOTE: On couplings [6,8,10,12,13], O-RING-141 [7] will be found adjacent to the GASKET GRABBER [18].
On COUPLING [2], O-RING-151 [3] is used. Replace the proper O-Ring before installing the coupling.
COUPLING AND BLITZ BASE INSTALLATION: Insert the GASKET GRABBER [18] debris screen into the coupling,
raised end pointing toward the front of the nozzle. Put the coupling onto the mating part and load the correct number of
balls into the ball groove. (SEE PARTS LIST ON EXPLODED VIEW OF NOZZLE TO DETERMINE CORRECT NUMBER OF
BALLS FOR YOUR COUPLING : 4, 17, or 45). The Blitz Bases and the couplings on Model HD-TO should be locked out,
therefore there is a small slot in the male ball groove which accomodates the end of the set screw to lock rotation.
Insertion of the balls is easier if the coupling is rotated slightly back and forth as the balls are loaded. Loctite and install
proper 1/4-28 SOCKET SET [5 or 16] screw. The set screw should be flush with the surface of the coupling. If the
coupling is difficult to turn, or feels rough when turned, the set screw is in too far. Back set screw off a turn or so, and try
again. If the feel is still not correct, recheck the number of balls in the coupling. On tip only couplings and blitz bases run
the screw into the slot on the ball groove until it bottoms out, without applying pressure.
©Copyright Task Force Tips, Inc. 2000
Page 1 of 7
LID-050 January 24, 2000 Rev 1
TIP ONLY BASE SERVICE: The TIP ONLY BASE [47] is retained on the TIP ONLY BARREL ASSEMBLY [73] by threads
which are retained by Loctite. Apply heat to the knurled rib nearest the front of the nozzle. Damage to seals and labels
can be reduced by protecting these with a wet rag. The TIP ONLY BASE can now be unscrewed. Remove and replace ORING-143 [48]. Clean all threads, apply Loctite to threads and screw together.
SHO-FLOW SERVICE PROCEDURE
Tools Required
3/32" Allen (hex) Wrench
Needle Nose Pliers
Small Screwdriver
Loctite #271 Thread Locking Adhesive
Torch, oxyacetylene or propane
SHO-FLOW DISASSEMBLY SEQUENCE
SHO-FLOW REMOVAL: Heat and remove 10-32x1/4 SOCKET SET [31] screws from the front of the S-F BODY [41],
using a 3/32" Allen wrench. Unscrew S-F BODY from the valve. Flush out any debris lodged in the TARGET [33] area.
WINDOW REMOVAL: Remove O-RING-139 [37]. Slide PLASTIC WINDOW [38] out of S-F BODY.
TARGET REMOVAL: Reach through flow window with a small screwdriver. Use screwdriver to push SMALLEY RING [36]
out of the groove. Gently pull SMALLEY RING out of S-F BODY using needle nose pliers. Make sure the SMALLEY RING
does not score the BACKDROP LABEL [32]. Pull on TARGET [33] using needle nose pliers. This procedure will remove
TARGET [33], WASHER [35] and INDICATOR SPRING [34] together.
SHO-FLOW ASSEMBLY SEQUENCE
TARGET INSTALLATION: Drop TARGET [33] and INDICATOR SPRING [34] (more closely spaced coils first) into S-F
BODY [41]. Push WASHER [35] past two O-RING-139 [37] and center over end of INDICATOR SPRING [34]. Easy
SMALLEY RING [36] into S-F BODY and groove using needle nose pliers. Make sure the SMALLEY RING does not score
the BACKDROP LABEL [32].
WINDOW INSTALLATION: Slide PLASTIC WINDOW [38] into S-F BODY [41] until it bottoms out on SMALLEY RING
[36].
SHO-FLOW INSTALLATION: Replace O-RING-139 [37] into S-F BODY groove. Thread S-F BODY [41] into VALVE
BODY. Apply Loctite to two 10-32x1/4 SOCKET SET [31] screw and turn into S-F BODY until tight.
VALVE SERVICE PROCEDURE
Tools Required:
3/32" Allen (hex) Wrench
1/8" Allen (hex) Wrench
7/32" Allen (hex) Wrench
Loctite #271 Thread Locking Adhesive
Torch, oxyacetylene or propane
VALVE DISASSEMBLY SEQUENCE
HANDLE REMOVAL: Heat, and then remove all screws [50, 52 and 53] on the HANDLINE HANDLE ASSEMBLY [51]
using 7/32" Allen wrench. The handle can now be removed.
SLIDER AND SEAL REMOVAL: Heat, and then remove 10-32 X 1/4 SOCKET SET [58] screws from the VALVE
ASSEMBLY, using 3/32 Allen wrench. Unscrew front portion of nozzle from valve. SLIDER [65] can now be pulled out
from front of valve. Remove and discard O-RINGS [63, 64, 48].
BOLT-ON PISTOL GRIP REMOVAL: Remove VALVE LABEL [56] using a razor knife. Remove adhesive with acetone or
methyl ethyl ketone. Then tap the HOLE CAP [66] into the valve body. Looking thru the top of the valve body, the
FLATHEAD ALLEN SCREW [28] retaining the PISTOL GRIP [43] to the valve will be exposed. Heat, and then remove the
screw using a 7/32 Allen wrench.
©Copyright Task Force Tips, Inc. 2000
Page 2 of 7
VALVE ASSEMBLY SEQUENCE
PISTOL GRIP INSTALLATION: Place the BOLT-ON PISTOL GRIP lugs into the holes located in the bottom of the valve
body. Apply Loctite to the threads of the FLAT HEAD ALLEN SCREW [28] and tighten securely. Using a small hammer
tap the HOLE CAP [66] into the valve body untill flush. Install a new VALVE LABEL [56].
SLIDER AND SEAL INSTALLATION: Insert O-RINGS [63,64,48] into the proper grooves in the valve body. Lubricate ORINGS and SLIDER with silicone grease. Push SLIDER [65] into the valve body.
HANDLE INSTALLATION: Insert DETENT SPRINGS [55] and DETENT FOLLOWERS [54] into the handle lugs, then
snap the handle into place, with offset holes FORWARD. Apply Loctite to two 3/8-24 X 3/4 BUTTON HEAD [53] screws,
and insert thru the lower handle holes. Thread each into corresponding center trunnion hole. Carefully align the groove
on Slider [65] with offset hole in handle. Apply Loctite to the SAFETY SCREW [50] and start into offset hole which is
closest to the front end of the valve. Screw down into engagement with groove in slider, until head of screw is flush with
handle. Repeat procedure for CAM SCREW [52]. Tighten button head screws securely. Handle should click firmly and
smoothly into all detent positions.
VALVE SHUTOFF ADJUSTMENT: Shut-off sealing of valve is adjusted by the threads between the valve body and the
front portion of the nozzle. While holding the HANDLINE HANDLE ASSEMBLY [51] against stops in the OFF position,
screw front end into the valve body until contact with the valve plug is felt. Open handle up to remove contact. Screw
together 1/12 turn further to give the valve shutoff compression. Loctite and replace SET SCREWS [58]. Thread in both
SET SCREWS until they bottom out, without applying pressure. In an alternating fashion, continue turning in SET
SCREWS a 1/4 turn each time till tight.
VALVE ADJUSTMENT FOR SEVERE COLD: To help to prevent hose line freezing in cold climates, the valve may be
adjusted for intentional leakage by unscrewing front end slightly. The valve may be returned to normal adjustment during
warm weather as above.
FRONT END SERVICE PROCEDURE
Tools Required :
1/8" Allen (Hex) Wrench
7/32" Allen (Hex) Wrench
3/16" Two Prong Face Spanner Wrench
.015" Feeler Gauge (used when replacing baffle)
Torch, oxyacetylene or propane
Dow #44 High Temperature Silicone Grease
Vise with padded jaws
Strap Wrench
Loctite #271 Thread Locking Adhesive
NOTICE: The Dual-Force pressure control unit is part of the BARREL ASSEMBLY [68 or 73]. This unit is factory
calibrated, and sealed. Service on this unit must be performed at the factory, using special tooling and equipment. In the
unlikely event that this unit should need service, please return the complete nozzle to the factory for repairs, or replace
the entire BARREL ASSEMBLY [68 or 73].
DO NOT ATTEMPT TO DISASSEMBLE THIS DEVICE! Task Force Tips, Inc. will assume NO liability for damage or
injury resulting from attempts to disassemble or repair the pressure control unit.
FRONT END DISASSEMBLY SEQUENCE
BAFFLE REMOVAL: Heat and remove BUTTON HEAD SCREW [93] using an 1/8" Allen wrench. Remove and discard
TEFLON WASHER [92]. Carefully remove the DUAL-FORCE KNOB [91]. Underneath the DUAL-FORCE KNOB there are
two SPRINGS [87] and two 3/16 STAINLESS STEEL BALLS [88], these should be removed also. Remove and inspect the
two O-RINGS [86] located in the BAFFLE ASSEMBLY [85]. Hold the barrel cone back in flush and apply heat to the small
shank on the BAFFLE ASSEMBLY [85]. Unthread the BAFFLE ASSEMBLY using a spanner wrench. Remove and replace
BAFFLE LABEL [90] if affected by the heat.
BARREL CONE SUB ASSEMBLY REMOVAL: Heat, and then remove two 3/8-24 X 3/8 DOGPOINT [71] screws on
BARREL ASSEMBLY [68 or 73] using a 3/16" Allen wrench. Place the barrel cone face down on the work surface. Pull the
barrel up and clear of the barrel cone. Four spring-loaded pins will be visible in the back of the barrel cone. Remove four
FLUSH PINS 1/8 X 1/2 FLAT [77] and four FLUSH SPRINGS [78]. Remove and replace O-RING-224 [76].
©Copyright Task Force Tips, Inc. 2000
Page 3 of 7
SHAPER REMOVAL: The rubber bumper is permanently bonded onto the stream shaper as a single unit, SHAPER
WITH BUMPER [83]. The shaper is attached to the SHAPER GUIDE [74] by a threaded joint that is retained by Loctite.
Grip rear portion of the nozzle in a vise with padded jaws. Direct a hot narrow flame around the rear portion of the shaper.
Heat for approximately 20 seconds, being careful not to damage the bumper or labels (a wet rag wrapped around these
areas will help). Use a strap wrench to unscrew the shaper from the shaper guide. Remove the shaper. Inside the shaper
are 46, 3/16 DELRIN BALLS [82], some of which may fall free as it is removed. If shaper is to be re-used, clean ball track
and replace O-RING-336 [81].
SHAPER GUIDE REMOVAL: The SHAPER GUIDE [74] does not need to be removed to service the BAFFLE [85] or
BARREL CONE [80]. To service the SHAPER GUIDE, heat and remove two 3/8-24 X 3/8 DOG POINT [71] screws. The
SHAPER GUIDE can now be removed.
FRONT END ASSEMBLY SEQUENCE
SHAPER GUIDE INSTALLATION: Slide the new SHAPER GUIDE [74] into place. Apply Loctite to the two 3/8-24 X 3/8
DOG POINT [71] screws, then screw in SHAPER GUIDE until contact is felt; finally back each screw out 1/2 turn.
BARREL CONE SUB ASSEMBLY INSTALLATION: Insert four FLUSH SPRINGS [78] and four FLUSH PINS 1/8 X 1/2
FLAT [77] into holes. Lubricate O-RING-224 [76], and O-RING-228 [72]. Slide the BARREL ASSEMBLY [68 or 73] down
onto the barrel cone. Align the set screw holes in the barrel with the corresponding slots on the barrel cone. Apply Loctite
to two 3/8-24 X 3/8 DOG POINT [71] screws and start into BARREL ASSEMBLY. Turn in both screws until they bottom
gently in their slots. Back each screw out 1/2 turn. Check barrel cone for smooth sliding action. If binding is felt, then readjust DOG POINT screws.
BAFFLE ASSEMBLY: Thread SHIELD [84] onto the BAFFLE ASSEMBLY [85] until it bottoms out. If the roll pin is lined up
with the cutouts on SHIELD, unthread SHIELD, rotate 90 degrees and rethread. There are only two correct thread
combinations due to the four lead thread on the baffle. Install both O-RING-010 [86] into face grooves on the BAFFLE
ASSEMBLY. Place a Spring [VM4190] and a 3/16 Stainless Ball [88] consecutively into each pocket in the BAFFLE
ASSEMBLY. Unthread the SHIELD 1/4 turn. Apply Loctite to the 10-32 thread in BAFFLE ASSEMBLY. Apply a small
amount of grease to bottom face of the DUAL-FORCE KNOB [91]. Place DUAL-FORCE KNOB onto the BAFFLE
ASSEMBLY engaging the DUAL-FORCE KNOB onto both the roll pin in the BAFFLE ASSEMBLY and the cutouts on the
SHIELD. DUAL-FORCE KNOB is centered within slots on the SHIELD. Place a new TEFLON WASHER [92] onto the 10-32
x 1/2 BUTTON HEAD [93]. Turn screw into the BAFFLE ASSEMBLY until it bottoms out then back screw out just enough
to allow the knob to rotate.
BAFFLE INSTALLATION: Apply Loctite to the 5/8 threads in the BAFFLE ASSEMBLY [85]. Screw the BAFFLE
ASSEMBLY onto end of the shaft. Place a spacer between the BARREL CONE ASSEMBLY [80] and the SHAPER GUIDE
[74]. Rotate the shaper guide all the way forward to lock the barrel cone in the forward position. MAKE SURE THE DUALFORCE KNOB IS TURNED TO THE STANDARD SETTING. Insert the .015" feeler gages (shipped with replacement baffle)
between the shield and the face on the barrel cone, on opposite sides of center. Tighten the BAFFLE ASSEMBLY
carefully until an even drag is achieved on both gages. Let Loctite set 1 hour.
SHAPER INSTALLATION: Install O-RING-336 [81] in the groove nearest the fog teeth in the SHAPER WITH BUMPER
[83]. Grease the O-RING and ball groove heavily. Place 46 3/16" DELRIN BALLS [82] into greased ball groove. Apply
Loctite to male thread on SHAPER GUIDE [74]. Start shaper onto the shaper guide threads, screw down until threads
bottom.
PROBLEMS
If you have any questions or problems, please feel free to call for assistance.
(800)-348-2686 • (219)-462-6161
TASK FORCE TIPS, INC.®
2800 EVANS AVENUE, VALPARAISO, INDIANA 46383-6940
http://www.tft.com
©Copyright Task Force Tips, Inc. 2000
Page 4 of 7
PARTS LIST
REF#. . . DESCRIPTION . . . . . . . . . . . QTY. . . . ORDER #
1. . . . . 2.5 Hose Gasket . . . . . . . . . . . . 1 . . . . . V31902
2. . . . . 2.5 Rocker Lug Coupling . . . . . 1 . . . . . P197**
3. . . . . O-Ring-151 . . . . . . . . . . . . . . . . 1 . . . . . V3300-151
4. . . . . 3/16 SS Ball . . . . . . . . . . . . . . . 48. . . . . V2120
5. . . . . 1/4-28x3/8 Socket Set . . . . . . . 1 . . . . . V1100
6. . . . . 2.5 British Instananenous . . . . . 1 . . . . . H687
7. . . . . O-Ring-141 . . . . . . . . . . . . . . . 1 . . . . . V3400-141
8. . . . . Storz Coupling . . . . . . . . . . . . . 1 . . . . . H686**
10 . . . . Storz Inner Coupling . . . . . . . . 1 . . . . . H685
11 . . . . Coupling Gasket 1.5 . . . . . . . . . 1 . . . . . V3130
12 . . . . 1.5 Rocker Coupling Full Time . 1 . . . . . H694**
13 . . . . 2.5 Rocker Lockout . . . . . . . . . 1 . . . . . P198**
14 . . . . 1.5 Rocker Coupling . . . . . . . . 1 . . . . . H697**
15 . . . . 2.5 Blitz Base . . . . . . . . . . . . . . 1 . . . . . H675
16 . . . . 1/4-28x1/4 Socket Set . . . . . . . 1 . . . . . V1030
17 . . . . 3/16 SS Ball . . . . . . . . . . . . . . 38. . . . . V2120
18 . . . . Gasket Grabber 1.5 “ Hard . . . 1 . . . . . H730-60D
20 . . . . 1.5 Blitz Base . . . . . . . . . . . . . . 1 . . . . . H674
21 . . . . 1/4-20 Acorn Nut Brass . . . . . . 8 . . . . . V2030
22 . . . . 1/4-20 Stud . . . . . . . . . . . . . . . 4 . . . . . V2050
23 . . . . 1/4 AN960C416 Washer . . . . . . 8 . . . . . V2040
24 . . . . Playpipe Handle . . . . . . . . . . . 2 . . . . . P220
25 . . . . Blitz Bracket . . . . . . . . . . . . . . . 4 . . . . . H676
26 . . . . Blitz Bracket W/Hook . . . . . . . . 1 . . . . . H677
27 . . . . SHOFLOW Name Label . . . . . . 1 . . . . . S1120
28 . . . . 3/8-16x1" Flat Head SHCS . . . . 1 . . . . . V1165
30 . . . . Calibration Label 250 GPM . . . . 1 . . . . . S1105
31 . . . . 10-32x3/16 Socket Set . . . . . . . 2 . . . . . V1080
32 . . . . Backdrop Label . . . . . . . . . . . . . 1 . . . . . S1130
33 . . . . Target . . . . . . . . . . . . . . . . . . . . . 1 . . . . . S1010
34 . . . . Indicator Spring . . . . . . . . . . . . . 1 . . . . . S1185
35 . . . . Washer. . . . . . . . . . . . . . . . . . . . 1 . . . . . S1030
36 . . . . #VH-218-S02 Smalley Ring . . . 1 . . . . . V4230
37 . . . . O-Ring-139 . . . . . . . . . . . . . . . . 3 . . . . . V3700-139
38 . . . . Plastic Window . . . . . . . . . . . . . 1 . . . . . S1020
40 . . . . Integral End . . . . . . . . . . . . . . . 1 . . . . . S1040
41 . . . . S-F Body W/Mounting Ho . . . . . 1 . . . . . S1081
42 . . . . PG Plug . . . . . . . . . . . . . . . . . . . 1 . . . . . S1095
43 . . . . SHO-FLOW Pistol Grip . . . . . . . 1 . . . . . S1090
44 . . . . VPG Pistol Grip . . . . . . . . . . . . . 1 . . . . . H690
45 . . . . 3/16 SS Ball . . . . . . . . . . . . . . 37. . . . . V2120
46 . . . . Gasket Grabber 1.5" Soft . . . . 1 . . . . . H730-70A
47 . . . . Tip Only Base . . . . . . . . . . . . . . 1 . . . . . H670
48 . . . . O-Ring-143 . . . . . . . . . . . . . . . . 1 . . . . . V3380-143
50 . . . . Safety Screw . . . . . . . . . . . . . . . 1 . . . . . H635
©Copyright Task Force Tips, Inc. 2000
REF#. . . DESCRIPTION . . . . . . . . . . . QTY. . . . ORDER #
51 . . . . Handline Handle Assembly . . . . 1 . . . . . H620
52 . . . . Cam Screw . . . . . . . . . . . . . . . . 1 . . . . . H630
53 . . . . Handle Screw . . . . . . . . . . . . . . 2 . . . . . H645
54 . . . . Detent Follower . . . . . . . . . . . . . 2 . . . . . H615
55 . . . . Detent Spring . . . . . . . . . . . . . . 2 . . . . . H770
56 . . . . Valve Label. . . . . . . . . . . . . . . . . 1 . . . . . H750
57 . . . . Stuffed H600 Valve Body . . . . . 1 . . . . . H900S
58 . . . . 10-32x1/4 Socket Set . . . . . . . 2 . . . . . V1070
60 . . . . #WH-212-S02 Smalley Ring . . . 1 . . . . . V4220
61 . . . . O-Ring-136 . . . . . . . . . . . . . . . . 1 . . . . . V3390-136
62 . . . . Stuffed Snap In Valve Body. . . . 1 . . . . . H903S
63 . . . . QUADX-4326 . . . . . . . . . . . . . . . 1 . . . . . V3360-4326
64 . . . . QUADX-4225 . . . . . . . . . . . . . . . 1 . . . . . V3370-4225
65 . . . . Slider . . . . . . . . . . . . . . . . . . . . . 1 . . . . . H660
66 . . . . Hole Cap . . . . . . . . . . . . . . . . . . 1 . . . . . B645
67 . . . . Stuffed H601 Valve Body. . . . . . 1 . . . . . H601S
68 . . . . Standard Barrel Assembly . . . . 1 . . . . . HD810
70 . . . . Dual-Force Barrel Label. . . . . . . 1 . . . . . HD740
71 . . . . 3/8-24x3/8 Dog Point. . . . . . . . . 2 . . . . . V1130
72 . . . . O-Ring-228 . . . . . . . . . . . . . . . . 2 . . . . . V3330-228
73 . . . . Tip Only Barrel Assembly . . . . . 1 . . . . . HD820
74 . . . . Shaper Guide Assembly . . . . . . 1 . . . . . HD812
75 . . . . Dual-Force Name Label . . . . . . 1 . . . . . HD745
76 . . . . O-Ring-224 . . . . . . . . . . . . . . . . 1 . . . . . V3320-224
77 . . . . Flush Pins . . . . . . . . . . . . . . . . . 4 . . . . . H790
78 . . . . Flush Springs . . . . . . . . . . . . . . 4 . . . . . H780
80 . . . . Barrel Cone Assembly. . . . . . . . 1 . . . . . H870
81 . . . . O-Ring-336 . . . . . . . . . . . . . . . . 1 . . . . . V3320-336
82 . . . . 3/16 Delrin Ball . . . . . . . . . . . . 46. . . . . V2115
83 . . . . Shaper With Bumper . . . . . . . . 1 . . . . . H500
84 . . . . Shield. . . . . . . . . . . . . . . . . . . . . 1 . . . . . HD562
85 . . . . Dual-Force Baffle . . . . . . . . . . . 1 . . . . . HD561
86 . . . . O-Ring-010 . . . . . . . . . . . . . . . . 2 . . . . . V3735-010
87 . . . . Spring #C0180-018-0250S . . . . 2 . . . . . VM4190
88 . . . . 3/16 SS Ball . . . . . . . . . . . . . . . 2 . . . . . V2120
90 . . . . Dual-Force Baffle Label . . . . . . 1 . . . . . HD752
91 . . . . Dual-Force Knob . . . . . . . . . . . 1 . . . . . HD560
92 . . . . Teflon Washer . . . . . . . . . . . . . . 1 . . . . . VW360X193/10
93 . . . . 10-32 X 1/2 Button Head . . . . . . 1 . . . . . VT10-32BH500
—- . . . . Loctite Mini Dispenser . . . . . . . —- . . . . V5010
—- . . . . Shaper Repair Kit . . . . . . . . . . . —- . . . . H940
—- . . . . Handle Repair Kit . . . . . . . . . . . —- . . . . H950
—- . . . . Valve Seal Repair Kit . . . . . . . . —- . . . . H960
—- . . . . Baffle Repair Kit . . . . . . . . . . . . —- . . . . HD914
—- . . . . 1.5 Rocker Lug Kit . . . . . . . . . . —- . . . . HD980
—- . . . . 2.5 Rocker Lug Kit . . . . . . . . . . —- . . . . HD984
Page 5 of 7
Page 5 of 7
©Copyright Task Force Tips, Inc. 2000
Page 6 of 7
1-1/2" ROCKER
2-1/2" ROCKER LOCKOUT
1-1/2" ROCKER FULL-TIME
MODEL TO
MODEL S-F
1-1/2" BLITZ
BRITISH INSTANTANEOUS
STORZ
2-1/2" BLITZ
BASES
2-1/2" ROCKER LUG
COUPLINGS
MODEL VPG
NOT REMOVABLE
PLAY PIPE HANDLES
STUFFED H600
VALVE BODY
©Copyright Task Force Tips, Inc. 2000
STUFFED H601
VALVE BODY
STUFFED SNAP-IN
VALVE BODY
Page 7 of 7
SLIDE VALVES
SERIAL NUMBER
FRONT END
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement