Spot Vital Signs LXI Device, Service Manual

Spot Vital Signs LXI Device, Service Manual
Welch Allyn Spot Vital Signs LXi
BP
SYS
mm g
DIA
mm g
127
73
TEMP
985
SpO2
Patient ID 0 2 4
Weight
Height
Respiration
%
4 WEST
BP
SYS
127
73
4 WEST
mm g
AM
Reading
01
TEMP
F
PULSE
DIA
mm g
/min
985
SpO2
62
Patient ID 0 2 4
Pain
Clear
Send/Next Reading
Enter
Weight
Height
Respiration
%
AM
Reading
01
F
PULSE
/min
62
Pain
Clear
Send/Next Reading
Enter
BR
AUn
Service Manual
Welch Allyn Spot Vital Signs LXi
Service Manual
iv
Welch Allyn Spot Vital Signs LXi
Copyright 2012 Welch Allyn. All rights are reserved. To support the intended use of the product described
in this publication, the purchaser of the product is permitted to copy this publication, for internal
distribution only, from the media provided by Welch Allyn. No other use, reproduction, or distribution of
this publication, or any part of it, is permitted without written permission from Welch Allyn.Welch Allyn
assumes no responsibility for any injury to anyone, or for any illegal or improper use of the product, that
may result from failure to use this product in accordance with the instructions, cautions, warnings, or
statement of intended use published in this manual.
Welch Allyn, Spot Vital Signs, SureBP Technology, and SureTemp are registered trademarks of Welch
Allyn.
Braun ThermoScan is a registered trademark of the Braun Company.
LNCS is a trademark of, and SET, LNOP, and Masimo are registered trademarks of, Masimo Corporation.
Possession or purchase of a Masimo SpO2-equipped device does not convey any express or implied
license to use the device with unauthorized sensors or cables which would, alone or in combination with
this device, fall within the scope of one or more of the patents relating to this device.
Nellcor and Oxi-Max are registered trademarks of Nellcor Puritan Bennett Inc.
Health o meter is a registered trademark of Sunbeam Products, Inc. used under license.
Software in this product is Copyright Welch Allyn or its vendors. All rights are reserved. The software is
protected by United States of America copyright laws and international treaty provisions applicable
worldwide. Under such laws, the licensee is entitled to use the copy of the software incorporated with
this instrument as intended in the operation of the product in which it is embedded. The software may not
be copied, decompiled, reverse-engineered, disassembled, or otherwise reduced to human-perceivable
form. This is not a sale of the software or any copy of the software; all right, title, and ownership of the
software remain with Welch Allyn or its vendors.
For information about any Welch Allyn product, call Welch Allyn Technical Support:
USA +1 800 289 2501
Canada +1 800 561 8797
European Call Center +353 46 90 67790
Germany +49 695 098 5132
Latin America +1 305 669 9003
Singapore +65 6419 8100
United Kingdom +44 207 365 6780
Australia +61 2 9638 3000
China +86 21 6327 9631
France +33 15 5695 849
Japan +81 3 6383 0852
Netherlands +31 202 061 360
South Africa +27 11 777 7555
Sweden +46 85 853 6551
Reorder #4500-89
Manual Material No. 718440 Ver. A
Welch Allyn
4341 State Street Road
Skaneateles Falls, NY
13153 USA
Printed in USA
Regulatory Affairs Representative
Welch Allyn Limited
Navan Business Park
Dublin Road
Navan, County Meath, Republic of Ireland
Service Manual
v
1 - Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warnings and Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Blood Pressure Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Temperature Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SpO2 Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Blood Pressure Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Temperature Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SpO2 Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrostatic Discharge (ESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Button Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connection Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Agency Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2 - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Purpose and Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Other Applicable Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Miscellaneous Mounting Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wall Mount Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mobile Stand Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Radio Mounting Accessory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Barcode Reader Mounting Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Spot Vital Signs LXi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
User Serviceable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Technical Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Field Replacement Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Service Loaners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Service Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Spot Vital Signs LXi Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Display Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Braun ThermoScan PRO 4000 Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Blood Pressure Hose and Cuff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Thermometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SpO2 Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Quick Reference Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
AC Power Transformer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
vi
Welch Allyn Spot Vital Signs LXi
3 - Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Internal Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4 - Spot Vital Signs LXi Technical Overview . . . . . . . . . . . . . . . . . . . . 37
System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Battery System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
“CPU I/O” Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CPU Core Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
+5V Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Clock/Calendar Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Mod F NIBP Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SpO2 and Thermometer Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
LCD Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
External Load (RS-232) Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
SureTemp Plus Thermometer Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Braun ThermoScan PRO 4000 Thermometer Interface . . . . . . . . . . . . . . . . 39
SpO2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Radio Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Bar Code Scanner Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Printer Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Interconnect Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5 - Maintenance and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Spot Vital Signs LXi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Blood Pressure Cuff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Blood Pressure Hose and Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
SureTemp Plus Thermometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Braun ThermoScan PRO 4000 Thermometer . . . . . . . . . . . . . . . . . . . . . . . 44
SpO2 Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Spot Vital Signs LXi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Braun ThermoScan PRO 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Spot Vital Signs LXi Firmware Upgrade CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Spot Vital Signs LXi Radio Configuration CD . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Product Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6 - Calibration and Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Required Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Pneumatic test assembly setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Power Supply Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Service Manual
vii
Battery Removal / Power Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Voltage Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Pressure verification test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Blood pressure calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
NIBP board Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Functional tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Temperature Functional Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Temperature test setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Changing the Calibration Set Point Temperature on the 9600 Plus Calibration
Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Welch Allyn SureTemp Plus Thermometers. . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Braun ThermoScan Pro 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Changing the Calibration Set Point Temperature . . . . . . . . . . . . . . . . . . . . . 85
7 - Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Blood Pressure Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Temperature Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
SpO2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Masimo Sensor Accuracy Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Masimo Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Nellcor Sensor Accuracy Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Nellcor Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Guidance and Manufacturer’s Declaration For Spot Vital Signs LXi Radio . . . . . 95
8 - Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Error Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Radio Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Service Work Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Spot LXi Radio Configuration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
9 - Supplies and Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Blood Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Pulse Oximetry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Masimo Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Nellcor Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Miscellaneous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Service Contracts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
viii
Welch Allyn Spot Vital Signs LXi
10 - Field Replaceable Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
11 - Disassembly and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Tool list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Key Pad Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
SpO2 Circuit Board Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Masimo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Nellcor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Blood Pressure Circuit Board Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
LCD Inverter Ballast Board Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
LCD Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Pump Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
RS232-Communication Circuit Board Disassembly . . . . . . . . . . . . . . . . . . . . . 138
Fan and Power Circuit Board Disassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Thermometry Circuit Board Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
SureTemp Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Braun ThermoScan PRO 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
12 - Repair Test Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
General Unit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
A-D Noise Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Leak Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Inflation Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Dump Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Pneumatic Accuracy Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Valve Control Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Voltage Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Blank Mode Current Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Back Light (Idle) Current Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Valve/Pump Mode Current Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Interface Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Temperature Option Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Accuracy Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Temperature Probe Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
SpO2 Option Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
SpO2 Functional Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
SpO2 Mode Current Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Fail Safe Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Over Pressure Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Over 15 mmHg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Interconnect Diagram 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Interconnect Diagram 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
1
1
Safety Summary
Introduction
All users of the Spot Vital Signs LXi must read and understand the safety summary, and
all additional specific warnings and cautions located throughout the documentation.
Warnings and Cautions
Familiarize all operating personnel with the general safety information in this summary.
Specific warnings and cautions are also found throughout this manual.
General Warnings
A warning statement in this manual identifies a condition or practice, which if not
corrected or discontinued immediately, could lead to patient injury, illness, or death.
These warnings pertain entirely to Spot Vital Signs LXi.
WARNING The information in this manual is a comprehensive guide to the
operation of Spot Vital Signs LXi. For best results, read this manual thoroughly
before using the device.
WARNING Spot Vital Signs LXi is designed for medical clinician use. Although
this manual may illustrate medical spot-check techniques, only a trained clinician
who knows how to take and interpret a patient’s vital signs should use this
device.
WARNING Spot Vital Signs LXi is not intended for use in environments that are
without health care practitioner supervision.
WARNING Spot Vital Signs LXi is not intended for continuous monitoring. Do
not leave the device unattended while taking measurements on a patient.
WARNING To ensure data integrity, save readings and clear the Spot Vital Signs
LXi display between patients.
WARNING The Spot Vital Signs LXi is not defibrillator proof.
WARNING Spot Vital Signs LXi is not intended for use during patient transport.
WARNING This device is not suitable for use in the presence of a flammable
anesthetic mixture with air or oxygen or nitrous oxide. An explosion may result.
2
Safety Summary
Welch Allyn Spot Vital Signs LXi
WARNING To ensure patient safety, use only accessories and supplies (i.e.,
cuffs, hoses, temperature probes, SpO2 sensors, etc.) recommended for or
supplied with Spot Vital Signs LXi. Using unapproved accessories with Spot Vital
Signs LXi can affect patient and/or operator safety.
WARNING Prevent fluid from entering any connectors on the device. Should
this occur, dry the connectors with warm air. Check the accuracy of all operating
functions.
WARNING Every three months, inspect the blood pressure cuff, SpO2 cable,
and other accessories for fraying or other damage. Replace as necessary.
WARNING Do not use Spot Vital Signs LXi on patients who are on heart/lung
machines.
WARNING Electric shock hazard. There are no user-serviceable parts inside Spot
Vital Signs LXi other than battery replacement (see “Battery Replacement” on
page 46). Only an individual specifically trained and approved for the repair and/or
verification of this specific Welch Allyn product may perform maintenance
procedures specifically described in this manual. For service, refer the device to
an Authorized Service Center.
WARNING This device is not intended for hand-held use during operation.
WARNING Do not autoclave.
WARNING This device complies with current required standards for
electromagnetic interference and should not present problems to other
equipment or be affected by other devices. As a precaution, avoid using this
device in close proximity to other equipment.
WARNING Welch Allyn is not responsible for the integrity of any mounting
installation. Welch Allyn recommends that the customer contact their Biomedical
Engineering Department or maintenance service to ensure professional
installation for safety and reliability of any mounting accessory.
WARNING The Spot Vital Signs LXi consists of high-quality precision parts.
Protect it from severe impact and shock. A qualified service technician must
check any Spot Vital Signs LXi that is dropped or damaged for proper operation
prior to further use. Do not use the Spot Vital Signs LXi if you notice any signs of
damage. Contact the Welch Allyn Technical Support Department for assistance.
WARNING Do not use an SpO2 finger clip sensor and a blood pressure cuff
simultaneously on the same limb. Doing so may result in inaccurate pulse rate
and perfusion readings.
WARNING All signal input and output (I/O) connectors are intended for
connection of only devices complying with IEC 60601-1, or other IEC standards
(for example, IEC 60950) as appropriate to the device. Connecting additional
devices to the Spot LXi may increase leakage currents. To maintain operator and
patient safety, it is necessary to consider the requirements of IEC 60601-1-1.
WARNING For proper patient electrical isolation, use only a Welch Allyn power
supply (4500-101A) to charge Spot Vital Signs LXi.
WARNING Do not use the manufacturer supplied charger for the weight scale
while it is attached to Spot LXi.
Service Manual
Safety Summary
3
Blood Pressure Warnings
These warnings pertain to the Spot Vital Signs LXi blood pressure feature.
WARNING Spot Vital Signs LXi is not intended to measure BLOOD PRESSURE
on neonatal patients. The AAMI SP10:2002 standard defines neonates as children
28 days or less of age if born at term (37 weeks gestation or more); otherwise up
to 44 gestational weeks.
WARNING To ensure pediatric blood pressure accuracy and safety, the Child
Reusable Two-Piece Blood Pressure Cuff (4500-01), Infant Durable One-Piece
Cuff (5082-82-4MQ), and the Infant Disposable One-Piece Cuff (5082-92-4MQ)
are the smallest cuffs approved for use with young children and infants. The
child’s arm must fit within the range markings on the cuff.
WARNING Avoid compression of the blood pressure hose or cuff tubing of Spot
Vital Signs LXi. This may cause system errors to occur in the device.
WARNING Patients who are experiencing moderate to severe arrhythmias may
give inaccurate blood pressure measurements.
WARNING Spot Vital Signs LXi does not operate effectively on patients who are
experiencing convulsions or tremors.
WARNING Use only Welch Allyn blood pressure cuffs and/or hoses. Using other
manufacturers’ blood pressure cuffs and/or hoses may produce inaccurate blood
pressure readings.
WARNING When several blood pressure measurements are taken on the same
patient, regularly check the cuff site and extremity for possible ischemia, purpura,
and/or neuropathy.
WARNING Do not place the cuff on any extremity that is used for intravenous
infusions or any area where circulation is compromised.
WARNING Excessive cuff tightness may cause venous congestion and
discoloration of the limb.
WARNING Wrapping the cuff too loosely (preventing proper inflation) may result
in errors.
WARNING Do not change the connector(s) on the blood pressure cuff tubing of
this device to luer type. Luer type connectors are commonly used in intravenous
infusion systems. Using the luer connectors on blood pressure cuff tubing
creates the risk that the blood pressure tubing could be mistakenly connected to
a patient's intravenous line, resulting in the introduction of air into the patient's
circulatory system.
4
Safety Summary
Welch Allyn Spot Vital Signs LXi
Temperature Warnings
These warnings pertain to the Spot Vital Signs LXi temperature feature.
SureTemp® Plus
These warnings are specific to the SureTemp Plus thermometer option.
WARNING Use only Welch Allyn probe covers. Using other manufacturers’
probe covers or no probe cover may produce temperature measurement errors
and/or inaccuracy.
WARNING Always use a probe cover whenever coming into contact with a
patient.
WARNING Long-term continuous monitoring beyond three to five minutes is
not recommended in any mode.
WARNING Oral/axillary probes (blue ejection button at top of probe) and blue
removable probe wells are used for taking oral and axillary temperatures only.
Rectal probes (red ejection button) and red removable probe wells are used for
taking rectal temperatures only. Use of the probe at the wrong site will result in
temperature errors. Use of the incorrect removable probe well could result in
patient cross-contamination.
WARNING The thermometer connectors and probe are not waterproof. Do not
immerse or drip fluids on these items. Should this occur, dry the connectors and
probe with warm air. Check all functions for proper operation and accuracy.
WARNING Do not take an axillary temperature through patient’s clothing. Direct
probe cover to skin contact is required.
WARNING Do not autoclave.
WARNING Use Welch Allyn single-use disposable probe covers to limit patient
cross-contamination.
WARNING Incorrect insertion of probe can cause bowel perforation.
WARNING Washing hands greatly reduces the risk of cross-contamination and
nosocomial infection.
WARNING To ensure optimal accuracy, always confirm that the correct mode is
selected.
Service Manual
Safety Summary
5
Braun Thermoscan PRO 4000
These warnings are specific to the Braun ThermoScan PRO 4000 thermometer option.
WARNING Keep the probe window clean, dry, and undamaged at all times to
ensure accurate measurements. To protect the probe window, always keep the
thermometer in the storage cover while transporting or when not in use.
WARNING Only use Braun ThermoScan probe covers with this thermometer.
Using other manufacturer’s probe covers or no probe cover may produce
temperature measurement errors and/or inaccuracies. If the thermometer is used
without a probe cover attached, clean the lens (see “Braun ThermoScan PRO
4000 Thermometer” on page 44).
WARNING Do not autoclave.
WARNING The thermometer is not waterproof. Do not immerse or drip fluids
on it. Should this occur, dry the thermometer with warm air. Check for proper
operation and accuracy.
SpO2 Warnings
These warnings pertain to the Spot Vital Signs LXi SpO2 feature.
WARNING Only use Spot Vital Signs LXi with Masimo or Nellcor SpO2 option
with Masimo or Nellcor brand sensors and accessories, respectively. Using the
wrong or unapproved sensors or cables may cause improper performance.
WARNING The SpO2 sensor and extension cables are intended for use only for
pulse oximetry measurements. Do not attempt to connect these cables to a PC
or any similar device.
WARNING Before using, carefully read the sensor Directions for Use, including
all warnings, cautions, and instructions.
WARNING Do not use a damaged sensor or pulse oximetry cable or a sensor
with exposed optical components.
WARNING Incorrect application or a long duration of use of an SpO2 sensor may
cause tissue damage. Inspect the sensor site periodically as directed in the
sensor’s Directions for Use.
WARNING Certain ambient environmental conditions, sensor application errors,
and certain patient conditions may affect SpO2 readings and pulse signal.
WARNING Do not immerse the sensor or patient cables in water, solvents, or
cleaning solutions (the sensors and connections are not waterproof). Do not use
irradiation, steam, or ethylene oxide for sterilization.
WARNING The SpO2 in the Spot Vital Signs LXi device is not intended for use
as an apnea monitor.
WARNING Consider the SpO2 an early warning device. As a trend toward
patient deoxygenation is indicated, use laboratory instruments to analyze blood
samples to completely understand the patient’s condition.
6
Safety Summary
Welch Allyn Spot Vital Signs LXi
WARNING Tissue damage can be caused by incorrect application or duration of
use of a Nellcor OxiMax sensor. Inspect the sensor site as directed in the sensor
Directions for Use.
WARNING Do not use the sensors during magnetic resonance imaging (MRI)
scanning. Induced current could potentially cause burns. The MS board pulse
oximeter may affect the MRI image, and the MRI unit may affect the accuracy of
the oximetry measurements.
WARNING Carefully route patient cabling to reduce the possibility of patient
entanglement or strangulation.
WARNING Failure to cover the Nellcor OxiMax sensor site with opaque material
in high ambient light conditions may result in inaccurate measurements.
General Cautions
A caution statement in this manual identifies a condition or practice, which if not
corrected or discontinued immediately, could lead to equipment failure, equipment
damage, or data loss.
These cautions pertain to the entire Spot Vital Signs LXi device.
Caution If the accuracy of any measurement is in question, check the patient’s
vital sign(s) with an alternate method and then check to verify the device is
functioning properly.
Caution Place the device on a secure surface or use one of the optional
mounting accessories.
Caution Do not place fluids on or near the device.
Caution It is recommended that the device is used within stated operating
temperature ranges (see “Environmental” on page 93). The device will not meet
its performance specifications if used outside these temperatures ranges.
Caution Always unplug the AC power transformer from the outlet before
moving the mobile stand to a new location.
Caution The basket has a three-pound weight limit. Take care not to exceed
this limit.
Caution When connecting a Health o meter® weight scale, only operate the
scale with battery power. Remove and discard the scale's AC power cord.
Caution When using the Health o meter scale, remove the two hex nuts on the
RS-232 cable, as supplied, before screwing the cable into the scale base.
Service Manual
Safety Summary
7
Blood Pressure Cautions
These cautions pertain to the Spot Vital Signs LXi blood pressure feature.
Caution Minimize extremity and cuff motion during blood pressure readings.
Caution If the blood pressure cuff is not at heart level, note the difference in
reading due to the hydrostatic effect. Add the value of 1.80 mmHg (.2 kPa) to the
displayed reading for every inch (2.5 cm) above heart level. Subtract the value of
1.80 mmHg (.2 kPa) from the displayed reading for every inch (2.5 cm) below
heart level.
Caution Proper blood pressure cuff size and placement is essential to the
accuracy of the blood pressure determination. See Reusable Two-Piece Cuff
Measurements or Durable One-Piece Cuff Measurements of the Directions for
Use for sizing information.
Caution The position and physiologic condition of the subject can affect a blood
pressure reading.
Temperature Cautions
These cautions pertain to the Spot Vital Signs LXi temperature feature.
Caution The SureTemp Plus feature only operates with the probe well in place.
Caution Do not use alkaline batteries in the Braun ThermoScan PRO 4000.
Caution Biting the probe tip may result in damage to the probe.
SpO2 Cautions
These cautions pertain to the Spot Vital Signs LXi SpO2 feature.
Caution The pulse oximeter is calibrated to determine the percentage of
arterial oxygen saturation of functional hemoglobin. Significant levels of
dysfunctional hemoglobin such as carboxyhemoglobin or methemoglobin may
affect the accuracy of the measurement.
Caution Some sensors may not be appropriate for a particular patient. If at
least 10 seconds of perfusion pulses cannot be observed for a given sensor,
change sensor location or sensor type for perfusion to resume.
Caution Physiological conditions, medical procedures, or external agents that
may interfere with the pulse oximeter’s ability to detect and display
measurements include dysfunctional hemoglobin, arterial dyes, low perfusion,
dark pigment, and externally applied coloring agents such as nail polish, dye, or
pigmented cream.
Caution When selecting a sensor, consider the patient’s weight and activity
level, the adequacy of perfusion, the available sensor sites, the need for sterility,
and the anticipated duration of monitoring.
8
Safety Summary
Welch Allyn Spot Vital Signs LXi
Electrostatic Discharge (ESD)
Electrostatic discharge is a sudden current flowing from a charged object to another
object or to ground. Electrostatic charges can accumulate on common items such as
foam drinking cups, cellophane tape, synthetic clothing, untreated foam packaging
material, and untreated plastic bags and work folders, to name only a few.
Electronic components and assemblies, if not properly protected against ESD, can be
permanently damaged or destroyed when near or in contact with electrostatically charged
objects. When you handle components or assemblies that are not in protective bags and
you are not sure whether they are static-sensitive, assume that they are static-sensitive
and handle them accordingly.
•
Perform all service procedures in a static-protected environment. Always use
techniques and equipment designed to protect personnel and equipment from
electrostatic discharge.
•
Remove static-sensitive components and assemblies from their static-shielding bags
only at static-safe workstations - a properly grounded table and grounded floor mat and only when you are wearing a grounded wrist strap (with a resistor of at least 1
megohm in series) or other grounding device.
•
Use only grounded tools when inserting, adjusting, or removing static-sensitive
components and assemblies.
•
Remove or insert static-sensitive components and assemblies only with monitor
power turned off.
•
Insert and seal static-sensitive components and assemblies into their original staticshielding bags before removing them from static-protected areas.
Always test your ground strap, bench mat, conductive work surface, and ground cord
before removing components and assemblies from their protective bags and before
beginning any disassembly or assembly procedures.
Service Manual
Safety Summary
Symbols
The following symbols are associated with the Spot Vital Signs LXi.
Safety Symbols
Identifies information within the
manual to avoid injury.
Caution: consult accompanying
documents
Identifies information within the
manual to avoid equipment failure.
Pb
Internally Powered, Lead Acid
Battery
Handle with Care
Transport Temperature
Storage Humidity
Recycle
MAX
Class II Equipment
IPXØ
Equipment is not protected against
the ingress of liquid.
Type BF Equipment
On/Off
Recycle the product separate from
other disposables, see “Product
Disposal” on page 48.
Non-ionizing radiation (RF
transmitter)
Mode of Operation: Continuous
DC Power In
Button Symbols
Navigation Buttons
Blood Pressure
Select
MEM
Memory
Power On/Off
Connection Symbols
USB Connection
Serial Port Connection
9
10
Safety Summary
Welch Allyn Spot Vital Signs LXi
Agency Symbols
CONFORMS TO:
UL STD 60601-1
IEC 60601-1
The CE mark on this product indicates that it has been tested to and conforms with
the provisions noted within the 93/42/EEC Medical Device Directive.
0297
Regulatory Affairs Representative
Welch Allyn Limited
Navan Business Park
Dublin Road
Navan, County Meath, Republic of Ireland
11
2
Overview
Purpose and Scope
The Spot Vital Signs LXi Service Manual is intended as a reference for maintenance and
repair to the field replaceable unit (FRU) level and are listed on page 121.
Note
Opening the Spot Vital Signs device case requires recalibration of specific
functions. This includes any internal components that were replaced. Calibration
requires the use of the Welch Allyn Spot LXi Tool.
This manual provides the technical qualified service person with troubleshooting
information, repair procedures, and calibration and performance verification instructions. A
technical overview of the Spot Vital Signs LXi subsystems is provided as an introduction
to the device’s circuitry and pneumatics.
This manual is intended for the technical qualified service personnel. Service training
classes on Welch Allyn’s products are available. Contact Welch Allyn Technical Support for
information.
Other Applicable Documents
The Spot Vital Signs LXi Directions for Use manual is also available. Refer to this
document for information other than maintenance and repair.
Welch Allyn 9600 Plus Calibration Tester Directions for Use - for all models.
Braun ThermoScan PRO 4000 User’s Guide - for models 450E0, 45NE0, 45ME0.
Masimo Directions for Use - for models 45MT0, 45ME0.
Nellcor Directions for Use - for models 45NT0, 45NE0.
12
Overview
Welch Allyn Spot Vital Signs LXi
Miscellaneous Mounting Accessories
Wall Mount Kit
WALL MOUNT KIT
EF: 4701-62
2
aterial #: 711890 Rev. B
Attach bracket to wall before
assembling basket.
1
3
}
5
4
Welch Allyn is NOT responsible for the integrity of any wall
mounting interface. Ensure you are using the appropriate
hardware to mount the device to a surface. Welch Allyn
recommends that the customer contact their Biomedical
Engineering Department or maintenance service to ensure
professional installation, safety, and reliability of any
mounting accessory.
Service Manual
Overview
13
14
Overview
Mobile Stand Kit
Welch Allyn Spot Vital Signs LXi
Service Manual
Overview
15
16
Overview
Welch Allyn Spot Vital Signs LXi
Radio Mounting Accessory
A
2
B
1
3
5
4
Service Manual
Barcode Reader Mounting Accessory
Overview
17
18
Overview
Welch Allyn Spot Vital Signs LXi
Warranty
Spot Vital Signs LXi
Welch Allyn warrants that the Spot Vital Signs LXi Radio products meet the labeled
specifications of the products and will be free from defects in materials and workmanship
that occur within one year after the date of purchase.
The date of purchase is: 1) the date specified in our records if you purchased the Product
directly from us, 2) the date specified in the warranty registration card that we ask you to
send to us, or 3) the date of purchase of product from the authorized Welch Allyn
distributor as documented from a receipt from said distributor.
This warranty does not cover damage caused by: 1) handling during shipping, 2) use or
maintenance contrary to labeled instructions, 3) alteration or repair by anyone not
authorized by Welch Allyn, and 4) accidents.
If a Product or accessory covered by this warranty is determined to be defective because
of defective materials, components, or workmanship, and the warranty claim is made
within the warranty period described above, Welch Allyn will, at its discretion, repair or
replace the defective Product or accessory free of charge.
You must obtain a service notification number from Welch Allyn to return your Product
before you send it to Welch Allyn’s designated service center for repair. Contact Welch
Allyn Technical Support.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. WELCH ALLYN’S OBLIGATION UNDER
THIS WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT OF PRODUCTS
CONTAINING A DEFECT. WELCH ALLYN IS NOT RESPONSIBLE FOR ANY INDIRECT OR
CONSEQUENTIAL DAMAGES RESULTING FROM A PRODUCT DEFECT COVERED BY
THE WARRANTY.
Accessories
Refer to the manufacturer’s Directions for Use for the Masimo and Nellcor finger sensor
and cable warranty.
Refer to the Directions for Use provided with the Welch Allyn Blood Pressure Cuff for
warranty information.
The SureTemp Plus probe is covered by a one-year warranty and the SureTemp Plus probe
well is covered by a 90-day warranty against original defects in material and workmanship.
Probe covers are intended for single-use only.
The Braun ThermoScan PRO 4000 is covered by a three-year warranty against original
defects in material or workmanship.
The printer is covered by a one-year warranty against original defects in material or
workmanship.
The barcode scanner is covered by a five-year warranty against original defects in material
or workmanship.
Service Manual
Overview
19
Service
Caution Unauthorized repairs will void the warranty.
All repairs on products under warranty must be completed by Welch Allyn or Welch Allyn
certified service personnel in accordance with warranty guidelines. See the Welch Allyn
Partners In Care™ web site (http://www.welchallyn.com/promotions/services/default.htm)
for a description of the different levels of services offered.
User Serviceable Parts
For user serviceable parts available see “Supplies and Accessories” on page 113.
Technical Assistance
If you have an equipment problem that you cannot resolve, call the Welch Allyn Service
Center nearest you for assistance. Technical service telephone support is available on
normal business days.
If you are advised to return a product to Welch Allyn for repair or routine maintenance,
schedule the repair with the service center nearest you.
Before returning a product for repair, you must obtain authorization from Welch Allyn.
Service personnel will give you a Service Notification number. Please note this number on
the outside of your shipping box. Returns without a Service Notification number will not
be accepted for delivery.
Field Replacement Units
See “Field Replaceable Units” on page 121.
Service Loaners
Service loaners or exchanges may be provided depending on the specific Partners In
Care™ agreement in place for the device. Loaners for products repaired while under the
original warranty, may be provided free of charge and are shipped within 48 hours of
notification of need.
For service repairs outside of warranty or outside of service agreement are available for a
nominal charge and shipment is subject to availability. Loaners are shipped pre-paid;
however, this charge is added to the service charges.
Service Intervals
Calibrate the Spot Vital Signs LXi on an annual basis for blood pressure, temperature, and
SpO2 accuracy.
20
Overview
Welch Allyn Spot Vital Signs LXi
Spot Vital Signs LXi Configurations
Table 1. Available Versions of Spot Vital Signs LXi
REF
Description
450T0
SureBP with SureTemp Plus Thermometer
450E0
SureBP with Braun ThermoScan PRO 4000 Thermometer
45MT0
SureBP with Masimo SpO2 and SureTemp Plus Thermometer
45ME0
SureBP with Masimo SpO2 and Braun ThermoScan PRO 4000 Thermometer
45NT0
SureBP with Nellcor SpO2 and SureTemp Plus Thermometer
45NE0
SureBP with Nellcor SpO2 and Braun ThermoScan PRO 4000 Thermometer
Controls
Figure 1. Spot Vital Signs LXi Front Panel with SureTemp Plus Thermometer
BP
SYS
mm g
DIA
mm g
127
73
TEMP
985
SpO2
Patient ID 0 2 4
Weight
Height
Respiration
%
SureTemp Plus
thermometer:
remove the probe
from the probe well to
take a temperature.
4 WEST
AM
Reading
01
F
PULSE
/min
Removable probe
well: store the
temperature probe
here when not in use;
remove to clean or
replace to eliminate
cross-contamination.
62
Pain
Clear
Send/Next Reading
Enter
Probe cover
storage area:
storage space for one
box of probe covers.
Navigation button: move
throughout the options in
the Navigation Window or
to increase/decrease
parameter units.
Select button:
accepts the current
option.
Power button: controls
power to the device.
Charging LED: indicates
when device is plugged in and
charging the battery.
Blood Pressure Start/Stop button:
initiates a new blood pressure cycle.
Pressing again aborts an active blood
pressure measurement.
Memory button:
recalls up to 50 most
recent readings.
Service Manual
Overview
21
Figure 2. Spot Vital Signs LXi Front Panel with Braun ThermoScan PRO 4000 Thermometer
BP
SYS
127
73
Braun ThermoScan PRO 4000
thermometer: store the probe
covers toward the back of the
thermometer housing; remove the
thermometer to access the covers.
4 WEST
mm g
DIA
mm g
TEMP
985
SpO2
01
F
PULSE
%
/min
62
Patient ID 0 2 4
Weight
Height
Respiration
AM
Reading
Pain
Clear
Send/Next Reading
Enter
BR
AUn
Navigation button: move
throughout the options in
the Navigation Window or
to increase/decrease
parameter units.
Memory button:
recalls up to 50 most
recent measurements.
Charging LED: indicates
when device is plugged in
and charging the battery.
Power button: controls
power to the device.
Charging LED: indicates
the thermometer battery
is charging.
Select button:
accepts the current
option.
Blood Pressure Start/Stop button:
initiates a new blood pressure cycle.
Pressing again aborts an active blood
pressure measurement.
22
Overview
Welch Allyn Spot Vital Signs LXi
Display Window
Note
Before using Spot Vital Signs LXi for the first time, you must program it using
the initial configuration screen.
1. Press the Power button. The display window shows the initial configuration screen.
Figure 3. Initial Configuration Screen
Change Local Defaults Menu
Model No.: 4 NTO
Serial No. 200 040004
Language:
BP Units:
Temperature Units:
eight Units:
Weight Units:
Date Format:
Date:
Time Format:
Time:
Select
2. Use the Select button to access the options and accept the entries, and use the
Navigation buttons to move through the menu.
3. The word “Exit” appears at the bottom of the list after you have programmed all
items in the menu. You must program all items before you can start to use the device.
4. Scroll to Exit and press the Select button to save the entries.
Service Manual
Overview
23
The liquid crystal display (LCD) may indicate any of the following: systolic blood pressure
(mmHg or kPa), diastolic blood pressure (mmHg or kPa), MAP (mmHg or kPa),
temperature (F or C), temperature mode, pulse rate, pulse signal level, SpO2 percent,
department location, date, time, record number, height (in or cm), weight (lb or kg),
respiration rate, pain level, connectivity signal strength, and battery charge level.
Figure 4. Display Window
X
Connectivity indicator: shows the
status of Spot LXi Spot LXi if the
device is sending a wireless reading.
Reading sent: indicates a
successful wireless send reading
attempt.
Reading not sent: indicates an
unsuccessful wireless send reading
attempt.
BP
Systolic and Diastolic
display: if MAP is turned on,
the screen toggles between
the systolic and diastolic
values, and the word “MAP”
and the MAP value.
SYS
mm g
DIA
mm g
127
73
TEMP
Temperature display and
indicator: shows the
temperature in Fahrenheit or
Celsius.
SpO2 display: shows the
percent saturation of arterial
hemoglobin. For devices with
SpO2 only.
Navigation Window: shows
menu options, error
messages, or temperature
conversion.
Location identifier: shows user
programmed location information. If no
location is entered, this area displays the
date.
Patient ID 0 2 4
Weight
Height
Respiration
%
Reading number indicator:
shows how many readings are
stored in memory. Spot Vital
Signs LXi retains up to 50
readings in memory.
AM
Reading
01
Battery level indicator: shows
the battery charge level.
985
SpO2
Clock: shows the current time.
4 WEST
F
PULSE
Thermometer probe setting
indicators: shows temperature
mode. For devices with SureTemp
Plus thermometer only.
/min
62
Pain
Clear
Send/Next Reading
Thermometer probe setting
indicators: shows Monitor
Mode. For devices with SureTemp
Plus thermometer only.
Out-of-range indicator: shows
the patient’s temperature reading
above or below the measurement
range limits. For devices with
SureTemp Plus thermometer only.
Enter
Pulse Signal Bar Graph: shows
the strength of the pulses detected.
Pulse display: shows the pulse
rate.
Clinician ID icons:
The figure icon signifies that Spot
Vital Signs LXi requires the clinician to
enter the Clinician ID.
The check mark signifies Spot Vital
Signs LXi has recorded the Clinician
ID.
For devices with a bar code scanner
only.
24
Overview
Welch Allyn Spot Vital Signs LXi
Connections
Use the following instructions to connect the blood pressure hose, thermometer probe,
and optional attachments to the Spot Vital Signs LXi.
Figure 5. Spot Vital Signs LXi Side and Rear Panel Connections
Icon ID label
CTIONS
ort
56
MAT: 7039
SureTemp Plus thermometer
connection port (for units
with SureTemp Plus only)
SpO2 cable connection port
(for units with SpO2 only)
II
I
Port I for external
device connection
Blood pressure hose
connection port
DC power connection port
USB connection for PC
(behind plug)
Port II for external
device connection
Battery door
Mobile stand or wall
mount screw connection
Service Manual
Overview
25
Braun ThermoScan PRO 4000 Lock
Press the lock tab toward the Braun ThermoScan PRO 4000 thermometer until it clicks. To
release the housing, insert the lock release pin into the lock release hole until the lock tab
snaps back.
Figure 6. Spot Vital Signs LXi with Braun ThermoScan PRO 4000 Lock
Lock release pin
Lock tab
Lock release hole
Blood Pressure Hose and Cuff
Identify and have available the Spot Vital Signs LXi, blood pressure cuff, and the blood
pressure hose.
1. Inspect the blood pressure hose; notice that one end has a single, gray connector
fitting and the other end has two white fittings.
2. Squeeze the side tabs on the gray connector and completely push the blood pressure
hose connector into the blood pressure hose connection port until it clicks into place
(see Figure 5 on page 24).
3. Twist the white connectors on the blood pressure hose and cuff connectors together.
26
Overview
Welch Allyn Spot Vital Signs LXi
Thermometer
Spot Vital Signs LXi is available with either the SureTemp Plus thermometer or the Braun
ThermoScan PRO 4000 thermometer.
SureTemp Plus
SureTemp Plus is available with two probes and matching wells; one for oral/axillary
temperatures (blue ejection button and probe well) and one for rectal temperatures (red
ejection button and probe well).
WARNING Always use a probe cover whenever coming into contact with a
patient.
Caution The SureTemp Plus feature only operates with the probe well in place.
1. Align the probe well with the tabs facing up and down into the round opening of the
SureTemp Plus housing on the right side of Spot Vital Signs LXi. Push it into place.
2. Align the temperature probe connector with the SureTemp Plus thermometer
connection port on the back of the Spot Vital Signs LXi (see Figure 5 on page 24). You
can only insert the connector into the port one way.
3. Press the tab on the connector and push it until it clicks into place.
4. Insert the temperature probe into the probe well.
Braun ThermoScan PRO 4000
Caution Do not use alkaline batteries in the Braun ThermoScan PRO 4000
thermometer. Use the rechargeable battery pack supplied by Welch Allyn.
1. Open the package of rechargeable batteries and follow the installation guide provided.
2. Open the box of probe covers as directed on the box and slide the box into the metal
guides toward the back of the thermometer housing with the opening at the top and
perforation facing forward.
3. Hold the Braun thermometer at a 45° angle then insert the probe and the top of the
thermometer into the housing.
4. Lower the bottom portion of the thermometer into the housing until it snaps into
place. If you do not properly seat the thermometer, it could fall out of the holder and
become damaged.
5. Slide the thermometer housing into the thermometer slot on the right side of the
Spot Vital Signs LXi device.
6. Push the lock tab forward to prevent the thermometer housing from falling out of
Spot Vital Signs LXi (see Figure 6 on page 25).
To release the lock, insert the lock release pin into the lock release hole.
Service Manual
Overview
27
SpO2 Sensor
Spot Vital Signs LXi is available with a wide variety of SpO2 sensors and ships with a
reusable finger clip sensor.
1. Align the shape and pin configuration of the extension cable connector to the SpO2
cable connection port on the left side of the Spot Vital Signs LXi device.
2. Push the connector firmly into the SpO2 cable connection port until you hear it click
into place (see Figure 5 on page 24).
3. Align the opposite end of the extension cable to the sensor cable connector and
firmly push them together.
WARNING Use only Masimo or Nellcor SpO2 sensors and accessories with the
Spot Vital Signs LXi with Masimo or Nellcor configurations, respectively. Using
the wrong or unapproved sensors or cables may cause improper performance.
Radio
CTIO NS
ort
6
MAT: 70395
The Spot Vital Signs LXi
identifies which serial port to
use after activating the Radio
in the internal configuration
mode.
II
I
Welch Allyn offers two
different radios:
• 802.11b radio and
• 802.11a/b/g radio
Only use Welch Allyn
Radios
PO
LIN WER
CO K
MM
Quick Reference Card
Attach the Quick Reference Card to the Spot Vital Signs LXi handle, mobile stand, or wall
mount using the supplied plastic cable tie.
28
Overview
Welch Allyn Spot Vital Signs LXi
AC Power Transformer
Note
To assure proper electrical isolation use only the Welch Allyn SPOT Vital Signs AC
power transformer/charger.
The operator can use the Spot Vital Signs LXi with AC or battery power (after charging the
battery).
1. Insert the round transformer connector into the AC power connection port on the
back of the Spot Vital Signs LXi (see Figure 5 on page 24).
2. Insert the line cord into the line connector on the transformer then plug the power
cord on the transformer into the AC main power source to charge the battery.
Printer
Once the printer is enabled in the Internal Configuration Mode, you can use plain or label
paper. If you use label paper, you must clean the printer heads after every 10 rolls. A head
cleaner kit is provided with each package of label paper available from Welch Allyn.
To connect the printer to the Spot LXi:
1. Connect the the large end of the cable (405210) to the Spot LXi.
2. Connect the small end of the cable (405210) to the Spot LXi printer.
Connect to Spot
LXi
Connect to Spot
LXi printer
To charge the Spot LXi printer:
1. Remove the guard on the power supply body (713703 or BC1300M) and attach the
appropriate power supply plug/adapter.
Service Manual
Overview
29
2. Connect the Spot LXi printer power supply to the Spot LXi printer.
3. Charge the Spot LXi printer for at least 9 hours before initial use.
To enable the Spot LXi printer:
1. Connect the Spot LXi printer to the Spot LXi.
2. Enable the printer in the Internal Configuration Mode of the Spot LXi (see “Internal
Configuration Mode” on page 32).
Battery
Charge the Spot LXi battery and printer battery (if using) for 9 hours before initial use.
Charge the device an additional hour if it includes a Braun ThermoScan PRO 4000
thermometer.
Note
While charging the Spot LXi, it is acceptable to charge the Spot LXi printer with
the power supply (713703 or BC1300M).
While Spot Vital Signs LXi is charging, the charging LED (~) flashes and the battery level
indicator segments on the display continuously sequence. When the battery is fully
charged, the charging LED stops flashing and the battery level indicator will stop
sequencing.
If the device includes a Braun ThermoScan PRO 4000 thermometer, the charging LED
below the thermometer will illuminate orange as it is charging. When the battery is fully
charged, the LED will power off.
If the Spot LXi has a mounted, external printer that is connected via the cable, the
charging LED on the printer flashes orange and green when the Spot LXi is plugged into
the AC main power source. If the Spot LXi has a mounted, external printer that is not
connected via the cable, the charging LED on the printer will not flash.
Note
There is no hazard associated with leaving the battery in the device, even if the
device is not used for long periods of time.
30
Overview
Welch Allyn Spot Vital Signs LXi
31
3
Functional Overview
This functional verification procedure helps to confirm the proper operation of the Spot
Vital Signs LXi and options. This procedure supports the requirements of routine
preventative maintenance. It is not necessary to disassemble the Spot Vital Signs LXi to
perform this procedure.
For the calibration procedures, see “Calibration and Verification” on page 49. If the Spot
Vital Signs LXi fails certain functional tests or a circuit board is replaced, the device may
require calibration. Always perform this functional verification procedure after performing
any calibration.
Self Test
The Spot Vital Signs LXi performs a self-test each time the device is powered on. Press
the Power button to turn the device on or off. Upon each power up, the display turns on,
two audible beeps occur, and the Spot Vital Signs LXi displays the model and serial
numbers. If the internal self-check is successful, the display shows its normal functions
(see Figure 4 on page 23) with all values blank, and the device is ready for operation. If the
self-check fails, an error code is shown in the Navigation Window (see “Error Codes” on
page 99).
Spot Vital Signs LXi automatically powers off when not used for 30 minutes.
32
Functional Overview
Welch Allyn Spot Vital Signs LXi
Internal Configuration Mode
You can change several device operating parameters in the Internal Configuration Mode.
When changed, these settings become the default power-up settings. You will also see
non-changeable device configurations for technical service purposes.
To Enter the Internal Configuration Mode:
1. Turn the Spot Vital Signs LXi off.
2. Press and hold the Select and Power buttons for 5 seconds. The device enters the
Internal Configuration Mode and the Configuration Menu screen appears on the
display.
Figure 7. Internal Configuration Mode Menu
Configuration Menu
Version
Numbers
Manual
Parameters
Battery
External
Devices
Location
Identifier
Save Readings
Date/Time
Buttons
Lockout
Blood Pressure
Defaults
Temperature
Event Log
Contrast
Select
3. Use the Navigation buttons to move through the menu options and then press the
Select button to access the options or accept a change. See the following tables for
descriptions of the menu options.
4. Press the Power button to exit the Internal Configuration Mode.
Service Manual
Functional Overview
33
Table 2. Configuration Menu Options
Setting
Description
Version Numbers*
Displays the software and hardware version numbers in the Spot Vital Signs LXi device.
Battery*
Displays the battery level.
Location Identifier
Allows the entry of the device’s location (e.g., the department name). Follow the
display prompts and use the Navigation and Select buttons to enter up to 10
characters.
Date/Time
Changes the date and time formats or updates the actual date and time. See Table 3,
“Date/Time Menu Options” for available settings.
Blood Pressure
Changes the blood pressure options. See Table 4, “Blood Pressure Menu Options” for
available settings.
Temperature
Changes the temperature options. See Table 5, “Temperature Menu Options” for
available settings.
Contrast
Changes the Display Contrast options. Use the left/right navigation buttons to adjust.
Manual Parameters
Changes the manual parameters defaults. See Table 6, “Manual Parameters Menu
Options” for available settings.
External Devices
Enables or disables available external devices. See Table 7, “External Devices Menu
Options” for available settings.
Save Readings
Saves the current patient reading at a preselected time interval or upon request. See
Table 8, “Save Readings Menu Options” for available settings.
Buttons Lockout
Secures Spot Vital Signs LXi so unauthorized people cannot use the device or access
data without enacting the proper key sequence. To override the buttons lockout feature,
simultaneously press the Left Navigation button and the Select button.
Defaults
Allows the user to select the default settings for the device and reset the unit to the
default settings. See Table 9, “Change Local Defaults Options” for available settings.
Event Log*
Displays the recent button presses, errors, measurements, measurement sites, battery
state changes, and patient reading send events.
* Displayed information only; operator cannot change.
Table 3. Date/Time Menu Options
Setting
Description
Date Format
Displays the date in one of the following styles:
• mm/dd/yyyy example: July 16, 2005 = 07/16/2005
• dd/mm/yyyy example: 16 July 2005 = 16/07/2005
Date
Changes the date on the Display Window and in patient readings. If a location is
entered (see “Location Identifier “ in Table 2, “Configuration Menu Options”), the date
will not appear on the Display Window; the location will.
Time Format
Displays the time in one of the following styles:
• 12-hour example: 5:00 PM
• 24-hour example: 17:00
Time
Changes the time on the Display Window.
34
Functional Overview
Welch Allyn Spot Vital Signs LXi
Table 4. Blood Pressure Menu Options
Setting
Description
BP Calibration Check
Prepares the Spot Vital Signs LXi for calibration. Only qualified personnel should verify
the Spot Vital Signs LXi blood pressure calibration. For more details, see “Blood
pressure calibration” on page 62.
Blood Pressure Units
mmHg or kPa.
Mean Arterial Pressure (MAP) On or off.
Table 5. Temperature Menu Options
Setting
Description
Temperature Units
Fahrenheit (°F) or Celsius (°C).
Temperature Mode
SureTemp Plus models only: Oral, Pediatric Axillary, Adult Axillary, and Last Mode. In
Last Mode the device takes the next temperature in the mode in which the previous
temperature was measured. Rectal Mode is available only when the rectal probe (red
ejection button) and probe well are attached.
Table 6. Manual Parameters Menu Options
Setting
Description
Height
On or off.
Height Units
Inches (in) or centimeters (cm).
Height Default
Changes the default patient height displayed in the Navigation Window.
Weight
On or off. Even if weight is enabled here, if weight scale is enabled in the External
Devices Menu, you cannot manually enter the weight.
Weight Units
Pounds (lb) or kilograms (kg).
Weight Default
Changes the default patient weight displayed in the Navigation Window.
Respiration
On or off.
Pain Level
On or off.
Service Manual
Functional Overview
35
Table 7. External Devices Menu Options
Setting
Description
Information System
On or off. You must enable this option to send patient readings wired or wirelessly.
Barcode Patient ID
On or off. You must enable this option to send patient readings wirelessly.
Barcode Clinician ID
On or off. You must enable this option to require mandatory sign in of a clinician.
Mandatory Sign In
Yes or no. You must enable this option to require the sign-in of the clinician.
Clear on Send/Save:
Yes or no. You must enable this option to clear the Clinician ID after sending or saving
the measurements.
Clear on Power Cycle:
Yes or No. You must enable this option to clear the Clinician ID after powering the Spot
Vital Signs LXi off.
Weight Scale
On or off. Spot Vital Signs LXi connects to a scale and the weight shows on the display
window (see “Spot Vital Signs LXi Technical Overview” on page 37 for scale details).
Wireless Module
None or DPAC. You must enable 802.11 B to send patient readings wirelessly. The radio
is available as an accessory only with Welch Allyn Connex.
Printer
On or off.
Printer Paper
Plain or labels. Only available if the Printer is enabled.
Table 8. Save Readings Menu Options
Setting
Description
Save Mode
Manual or automatic. If automatic, Spot Vital Signs LXi saves readings at a preselected
time interval. For either option, Spot Vital Signs LXi automatically saves the measured
parameters into memory before automatically powering off when not used for 30
minutes.
Auto Save Interval
Changes the amount of time before automatically saving the current patient reading.
Only available if Automatic Save Mode is enabled.
Reading Full Action
Auto Overwrite, Ask Overwrite, Do not Overwrite. Spot Vital Signs LXi can save 50
patient readings in memory. Upon reaching reading 51, the device may automatically
overwrite reading 1, ask the user if he/she wants to overwrite reading 1, or disable the
ability to take another reading until at least one reading is erased.
Table 9. Change Local Defaults Options
Setting
Description
Language
English, Dansk, Nederlands, Suomi, Français, Deutsch, Italiano, Norsk, Español,
Português, Svenska, or Chinese.
BP Units
mmHg or kPa.
Temperature Units
Fahrenheit (°F) or Celsius (°C).
Height Units
Inches (in) or centimeters (cm).
Weight Units
Pounds (lb) or kilograms (kg).
Date Format
Displays the date in one of the following styles:
• mm/dd/yyyy example: July 16, 2005 = 07/16/2005
• dd/mm/yyyy example: 16 July 2005 = 16/07/2005
Time Format
Displays the time in one of the following styles:
• 12-hour example: 5:00 PM
• 24-hour example: 17:00
36
Functional Overview
Welch Allyn Spot Vital Signs LXi
37
4
Spot Vital Signs LXi Technical
Overview
System Description
The Spot Vital Signs LXi automatically measures systolic and diastolic pressure (excluding
neonates), pulse rate, temperature (oral, adult axillary, pediatric axillary, rectal, and ear),
and pulse oximetry (SpO2) as well as calculates Mean Arterial Pressure (MAP).
Furthermore, Spot Vital Signs LXi allows the entry of height, weight, respiration rate, and
pain level. Spot Vital Signs LXi also calculates Body Mass Index (BMI) following height and
weight entry.
The device is intended to be used by clinicians and medically qualified personnel. It is
available for sale only upon the order of a physician or licensed health care provider.
Refer to the Spot Vital Signs LXi Directions for Use manual for complete information.
Battery System
Spot Vital Signs LXi uses a fuse and a shunt diode on the main board as well as a fuse in
the battery assembly for protection against reverse battery connections. The fuse is
located on the main board in the negative battery line. In the event of a reverse battery
connection, a blown fuse will require replacement. The negative line location is more
likely to short the battery (+) wire to ground than short the battery (-) wire to the VBUS
node.
Battery Charger
Provides two levels of power to fast-charge or to float the battery at fixed voltages using
software control. The fast-charge level rapidly brings the battery up to near-full capacity (7
Volts) using software to not overcharge the battery. The float level, set per the
manufacturer’s recommendation, slowly tops-off the battery and can stay on indefinitely.
“CPU I/O” Power Supply
Provides power to the I/O pins of the DragonBall MPU and the attached peripheral IC’s.
The nominal voltage is set to a value of 3.15 Volts so that both the 3.0 Volt MPU and 3.3
Volts peripherals can operate within specifications. Spot Vital Signs LXi uses buck
switching topology for efficiency and an on-off power latch directly controls the power
supply.
38
Spot Vital Signs LXi Technical Overview
Welch Allyn Spot Vital Signs LXi
Standby Mode
The Standby Mode conserves battery power. The device goes into Standby Mode if it is
not used for two minutes. Press any button to bring the Spot Vital Signs LXi out of
Standby Mode.
CPU Core Power Supply
Powers the MPU core only and operates at the recommended Dragonball voltage range
of 1.8 +/- 0.1 Volts; 2.0 Volts absolute max.
The +3.15 Volt supply powers the +1.8 Volt supply for efficiency and, more importantly, for
power sequencing. During power-on the +1.8 Volt supply cannot exceed the +3.15 Volt
supply. The R207/C182 further delays the +1.8 Volt supply. During power-off, D106
prevents the +1.8 Volt supply from exceeding the +3.15 Volt supply by more than a partial
diode drop.
+5V Supply
Provides supply to miscellaneous loads that require more than 3.15 Volts. The Power
Latch controls the supply and the average load current is small, so efficiency is not
important.
Clock/Calendar Power
The Clock/Calendar U19 receives power from two sources. During power on the clock
runs from the +5 Volt supply and during power down the clock receives power directly
from the battery potential using a voltage divider. Capacitor C131 provides power to the
U19 during the battery exchanges. Zener D102 prevents overvoltage to U19 in the case of
operation directly from the charger.
Mod F NIBP Power
This module is powered directly from VBUS through an EMI filter. Software via BP-PWRON-BAR controls the power. Level shifter Q115 / Q104 assures that the module remains
off when the MPU is unpowered.
SpO2 and Thermometer Power
A common structure supplies SpO2 and thermometry. A single push-pull driver delivers
square wave power to a pair of isolation transformers, one for SpO2 and the other for
thermometry. THERM-PWR-BAR activates the driver under software control. Level shifter
Q118, Q119 assures that the module remains off when the MPU is unpowered.
In the push-pull (forward) configuration, VBUS is multiplied by the transformer turns ratio
and supplied to the input of the rectifier diodes. This is filtered and passed through lownoise 5-Volt linear regulators to supply power to the parameter modules.
LCD Power
The LCD data interface connects directly to the +3.15 Volt MPU I/O power supply. This
powers the driver ICs inside the LCD pane and assures the data interface to the LCD is
always powered when the unit is powered.
Service Manual
Spot Vital Signs LXi Technical Overview
39
The contrast (bias) supply to the LCD panel and the LCD CCFL backlight both derive
power indirectly from a pre-regulator. A software control can shut down the pre-regulator.
For efficiency, it is implemented as a buck switcher operating directly from the battery.
The primary purpose of the pre-regulator is to protect the backlight inverter / ballast from
battery voltages that it cannot tolerate and to control current out of the unregulated
ballast. The voltage is set to the low side of 5 Volts to reduce battery consumption, while
still driving the CCFL with adequate voltage.
External Load (RS-232) Power
There are two power outlet means on the Spot Vital Signs LXi – RS-232 port power and
the Braun PRO 4000 charger.
Two isolated power supplies provide power to each of the external RS-232 ports. This
power is available to external devices on pin 9 of each serial connector whenever the
software enables the corresponding RS-232 port.
SureTemp Plus Thermometer Interface
The SureTemp Plus OEM module is located in an optional pod and is connected to the
main PCB via a flex cable.The Thermometer Probe connection is located on a separate PC
board. It is connected to the SureTemp Plus OEM module by a ribbon cable. The electrical
interface to the thermometer pod is a 6-pin ribbon connector, Molex 52271-0690 or
equivalent.
Braun ThermoScan PRO 4000 Thermometer Interface
The interface to the Braun ThermoScan PRO 4000 thermometer is located in the optional
pod and connects to the main PCB via a flex cable. The communications link is a single
duplex current loop that also charges the Braun battery pack.
The presence or absence of current passing through the Braun ThermoScan PRO 4000
charge contacts controls the interface charge LED, located within the pod, which mimics
the Braun ThermoScan Pro 4000 Base Station (type 6021).
SpO2 Description
A shielded flat-flex cable connects the user interface sensor connector J8 to the SpO2
electronics.
The Masimo SpO2 module mates to the Masimo Adaptor Board that, in turn, mates to the
Main board. This provides power and communications to the module from the Main
board.
The Nellcor SpO2 module mounts directly to the Main board. This provides power and
communications to the module, and brings the sensor signals to the main board where
EMI and ESD can be controlled. The sensor signals pass through the main board to the
mating connector for the shielded flat-flex cable.
40
Spot Vital Signs LXi Technical Overview
Welch Allyn Spot Vital Signs LXi
Radio Description
For the wireless radio description, refer to the manufacturer’s Directions for Use.
The radio interfaces to the Spot Vital signs LXi through an RS-232 female connector with a
9-pin male/female null modem connection.
Figure 8. 9-pin Null Modem Pinout
MA 0051 (DB9M/F) Adapter Pin out:
09 Male
09 Female
2
3
3
2
4
1+6
5
5
1+6
4
7
8
8
7
9
9
G
G
Bar Code Scanner Description
The Spot Vital Signs LXi has a 2D scanner (IMAGETEAM™ 4600). This scanner is
programmed specifically for Welch Allyn. Scanners not purchased through Welch Allyn
will not work with the Spot Vital Signs LXi.
Interface
The bar code scanner interfaces to Spot Vital Signs LXi through an isolated RS-232 DB-9
female connector. Use Welch Allyn part number 4500-910 for the barcode option.
Service Manual
Spot Vital Signs LXi Technical Overview
41
Printer Description
The SPOT Vital Signs LXi interfaces with printer kit 4500-500.
Table 10. LED Pattern Table
Pattern
Battery
Buffer Mode
Constant Green
Running
Normal
Fast Flashing Green
Running
Spool *
Long Green - Short Red
Battery Low
Normal
Short Green - Short Red
Battery Low
Spool *
Short Green - Long Orange
Trickle Charging
Normal
Long Orange Flash
Trickle Charging
Spool *
Fast Flashing Orange
Fast charging
Spool (Printing prohibited)
Fast Flashing Red
Error Condition
Spool (Printing prohibited)
No Light
Flat or in sleep mode
* Spool may have resulted from Paper Out or Head Up conditions)
No hardware power switch is fitted, as power control is either automatic or by command
from the host computer. To save power, the printer enters sleep mode after a period of
inactivity, factory-set to 30 seconds.
The printer external power supply is used to charge the printer batteries.
42
Spot Vital Signs LXi Technical Overview
Welch Allyn Spot Vital Signs LXi
Interconnect Diagram
(For drawing details see “Interconnect Diagram 1” on page 147 and see “Interconnect
Diagram 2” on page 148.
Item
Description
Item
Description
A1
PCA, Main, Spot Vital Signs LXi
W1
Assy, Power Harness, Spot Vital Signs LXi
A1-F1
Fuse, FlastBlo, 5A
W1-A1
PCA, Power Interface, Spot Vital Signs LXi
A2
PCA, Serial Interface, Spot Vital Signs LXi
W2
Flex, Main, Spot Vital Signs LXi
A3
Display, LCD, 320 x 240, Mono
W3
Cbl Flx, 1/2mm, 15 POS
A4
Inverter, LCD
W4
Assy, Ballast Harness, Spot Vital Signs LXi
A5
Assy, Battery, Spot Vital Signs LXi
W5
Assy, LCD Gnd Harness
A5-F1
Wire Protection Fuse
W6
Assy, Cable, Flat Flex, SpO2
A6
Assy, Fan Unit Cooling
Wire Clip, Side Entry,.375 Wide
A7
PCA, Masimo Adapter, Spot Vital Signs LXi
Foam Strip, 2 Sided Adhesive
A8
Masimo MS-11 SpO2
W7
Cbl, Flx, 1mm, 6POS
Shield, Masimo EMI
W8
Cbl, Flx, 1mm, 8POS
Tape, Copper, Masimo Shield
W9
Cbl, Flx, Braun, Spot Vital Signs LXi
A9
PCA, SureTemp Plus, OEM w/o EDAC
A10
PCBA, BP OEM, (MOD F)
A11
Assy, Pump, and Tubing, Spot Vital Signs
LXi
A11-F1
Filter, Air, 1/8 Barbs
A12
Assy, Transducer Tubing, Spot Vital Signs
LXi
A13
PCA, EDAC, Spot Vital Signs LXi
A14
Nellcor MP506 SpO2 PCB
A15
PCA, Braun Interface, Spot Vital Signs LXi
Wire Color
BLK
Black
BRN
Brown
RED
Red
ORN
Orange
GRN
Green
BLU
Blue
PNK
Pink
43
5
Maintenance and Service
Cleaning
WARNING Before performing any maintenance or service to the Spot Vital
Signs LXi, disconnect the AC power line from the electrical outlet.
Spot Vital Signs LXi
Caution Prevent water or other fluids from entering any connectors. If the
connectors get wet, dry them with warm air. Check all measurement functions.
Caution Do not sterilize or autoclave the Spot Vital Signs LXi device.
As necessary, clean the device with a cloth slightly dampened with either 70% isopropyl
alcohol, 10% chlorine bleach solution, or mild detergent in water, or use PDI Sani-System
Cloths. Never immerse Spot Vital Signs LXi in any type of fluid.
Blood Pressure Cuff
Before washing the Reusable Two-Piece Cuff, remove the two connectors and bladder,
close off tubes with plugs (available as accessory 5082-163), and close the hook and loop
fasteners. After washing, allow the cuff to air dry. Re-assemble the tube fittings.
Never press with an iron.
Blood Pressure Hose and Cable
Wipe the pressure hose with a damp cloth moistened in a mild detergent solution. Do not
immerse hose.
44
Maintenance and Service
Welch Allyn Spot Vital Signs LXi
SureTemp Plus Thermometer
Temperature Probe
Caution DO NOT immerse or soak the probe in any type of fluid.
Caution DO NOT use steam, heat, or gas sterilization on the probe.
Caution DO NOT autoclave the probe.
Press down on the connector tab and slide the connector out of the port to remove the
temperature probe.
Regularly wipe the probe with a cloth dampened with warm water and a mild detergent
solution, a 70% isopropyl alcohol solution, or a 10% chlorine bleach solution.
Removable Probe Well
Caution DO NOT use hard or sharp objects to clean the probe well. This could
damage the probe well and cause the device to not function properly.
Caution DO NOT use steam, heat, or gas sterilization on the probe well.
Caution DO NOT autoclave the probe well.
1. Remove the temperature probe from Spot Vital Signs LXi (see “Temperature Probe”
on page 44).
2. Grasp the well under the probe opening and pull up gently to remove it from the
device.
3. Swab the inner and outer surface of the probe well with a cloth dampened with a mild
detergent solution, 70% isopropyl alcohol, or 10% chlorine bleach solution. Immerse
the probe well in mild detergent solution as necessary for cleaning.
4. Dry all surfaces thoroughly before re-assembling the device (see “SureTemp Plus” on
page 26) for reassembly instructions.
Braun ThermoScan PRO 4000 Thermometer
Use a soft cloth slightly moistened with alcohol to clean the thermometer display and
exterior. Do not use abrasive cleaners.
Damage to the probe tip or the presence of dirt or cerumen on the probe tip can affect the
accuracy of your temperature measurement. To clean the tip, gently wipe it with a cotton
swab slightly moistened with alcohol and immediately wipe dry with a clean cotton swab.
Allow to dry at least five minutes before taking a temperature.
Every month, clean the Braun ThermoScan PRO 4000 charging contacts within the Spot
Vital Signs LXi housing with a swab slightly dampened with alcohol.
Service Manual
Maintenance and Service
45
SpO2 Sensors
WARNING Do not immerse the sensor in water, solvents, or cleaning solutions
(the sensors and connections are not waterproof). Do not use irradiation, steam,
or ethylene oxide for sterilization.
Clean the reusable SpO2 sensor with a 70% isopropyl alcohol solution. Do not immerse
the sensor.
Radio
Refer to Manufacturer’s Directions for Use.
Printer
The printer label kit comes with a two-step head cleaner. Follow the directions provided
with the cleaner.
46
Maintenance and Service
Welch Allyn Spot Vital Signs LXi
Battery Replacement
Spot Vital Signs LXi
Caution Only use the Welch Allyn 4500-84 lead acid battery. Using an incorrect
battery will cause damage to the Spot Vital Signs LXi and void the warranty.
Caution Do not break the shrink-wrap around the battery.
If necessary, replace the internal battery after heavy use or the battery no longer charges.
1. Power off the Spot Vital Signs LXi and disconnect the AC power transformer cord.
2. Remove the four screws holding the battery door using a phillips-head screwdriver.
Remove the battery door to expose the battery.
3. Tip the Spot Vital Signs LXi backward and slide the battery out. Disconnect the oneway connector and then attach a new battery to the connector as shown. The oneway connector ends only connect one way. Do this as quickly as possibly to prevent
loss of clock time.
Figure 9. Battery Removal and One-way Connector
One-way
connector
4. Slide the battery into the compartment as far as it will go. Push the connector down
into the case next to the battery.
5. Replace the battery door and tighten each of the four screws.
6. Connect the AC power transformer to the Spot Vital Signs LXi and allow the new
battery to charge for approximately 9 hours. The rechargeable batteries in the Braun
ThermoScan PRO 4000 thermometer require an additional 1 hour to charge. You can
use the Spot Vital Signs LXi during this charging period via the AC power cord.
If Spot Vital Signs LXi displays the E38 error code after power up, set the date (see
“Date/Time Menu Options” on page 33).
The battery is a non-spillable lead-acid battery and must be recycled or
disposed of properly according to national or local regulations.
Braun ThermoScan PRO 4000
Caution Do not use alkaline batteries in the Braun ThermoScan PRO 4000
thermometer.
Service Manual
Maintenance and Service
47
Welch Allyn supplies a rechargeable battery pack with the Braun ThermoScan PRO 4000
thermometer.
1. Open the battery compartment.
2. Remove the battery pack and replace with a new battery pack, verify the poles are in
the right direction.
3. Slide the battery door back in until it snaps into place.
If the battery is completely discharged, the LEDs will not illuminate. Allow the unit to
charge at least 15 minutes before proceeding.
The battery is a rechargeable battery and must be recycled or disposed
of properly according to national or local regulations.
Printer
Caution Do not use alkaline batteries in the printer.
1. Open the battery compartment.
2. Remove the battery pack and replace with a new battery pack, verify the poles are in
the right direction.
3. Slide the battery door back in until it snaps into place.
Allow the printer to charge at least 9 hours before proceeding.
The battery is a rechargeable battery and must be recycled or disposed
of properly according to national or local regulations.
48
Maintenance and Service
Welch Allyn Spot Vital Signs LXi
Spot Vital Signs LXi Firmware Upgrade CD
This CD upgrades the Spot Vital Signs LXi unit software version. A detailed procedure is
available on the upgrade CD.
Spot Vital Signs LXi Radio Configuration CD
The software on this CD configures the Spot Vital Signs LXi Radio for use on a local
wireless network.
Product Disposal
Do not dispose of this product as unsorted municipal waste. Prepare this product for
reuse or separate collection as specified by Directive 2002/96/EC of the European
Parliament and the Council of the European Union on Waste Electronic and Electrical
Equipment (WEEE). If this product is contaminated, this directive does not apply.
For more specific disposal information, see www.welchallyn.com/weee,or contact Welch
Allyn Customer Service at +44 207 365 6780.
49
6
Calibration and Verification
Terms
BP test volume repair fixture. Equipment with four separate 100cc, 250cc, and two
500cc linearity volume cylinders. Referred to in this procedure as “Test Volume”.
Calibration. Process to change the outputs of the UUT that are out of range. After saving,
the changes become permanent until the next calibration.
Pneumatic test assembly. Equipment that connects the UUT, the pressure meter, the
squeeze bulb, and the BP test volume repair fixture.
Spot LXi Service Tool. Software package to verify and calibrate the Spot LXi device.
Service computer. Computer with the repair software loaded and ready to operate.
Functional Tests. Process to check the outputs of the UUT.
UUT. Unit under test.
50
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Required Test Equipment
Description
Part Number
Qty
Power supply, 0-10 Volts, 2 amps capacity or better, fine voltage adjustment required
Digital multi meters (DMM)
2
Battery simulator connector, 24 inch or shorter
Patch cords- banana plug to banana plug, Red, 18 AWG, 24 inch or shorter
3
Patch cords- banana plug to banana plug, Black, 18 AWG, 24 inch or shorter
2
USB Cable, 2.0/5-Pin Mini-B Cable
Calibrated pressure meter
PC running Spot Lxi Service Tool (Ver 3.0 or greater)
4500-905
9600 Plus Temperature Calibration Tester
01802-110
Nellcor-approved SpO2 simulator, for devices with Nellcor option
SRC-MAX
Masimo SpO2 Tester, for devices with Masimo option
1795
Thermometer Calibration Key, Optional
06138-000
Blood pressure two-tube hose with Y fitting
5082-183
Blood pressure two-tube hose (standard cuff)
4500-30
BP test volume repair fixture (includes items below)
Note This is the new Test Volume needed for passing the NIBP Linearity Test
407672
BP test volume repair fixture. Must have at least the following volume cylinders: 100cc,
250cc, and 500cc
Squeeze bulb with bleeding screw
Square (4-way) tube fitting connector
12-inch (30.5 cm) tubing with.25-inch (6.35 mm) ID
4
Pneumatic test assembly setup
1. Connect the squeeze bulb with bleed screw to a square (4-way) tube fitting connector,
a calibrated pressure meter, a test volume, and to a blood pressure two-tube, Y-fitting
hose as shown in Figure 1 on page 51.
Service Manual
Calibration and Verification
Figure 1. Pneumatic test assembly setup
Test volume
100 CC
500 CC
LINEARITY
250 CC
500 CC
51
52
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Power Supply Test Setup
1. Connect the power supply to the Battery Simulator connector, banana plug patch
cords, digital multi meter (DMM) for voltage monitoring, DMM for current monitoring.
Figure 2. Power Supply Test Setup
Power supply
DMM
DMM
DMM connections
Test the power supply output as shown in Figure 3. Observe the correct polarity.
Figure 3. Power Supply
Service Manual
Calibration and Verification
53
2. Turn on the power supply and adjust to 6.5 +/- 0.1V DC before connecting the UUT.
Turn off power supply.
3. Disconnect the UUT battery and connect the external power supply to the UUT, using
the Battery Simulator. Observe the correct polarity.
Caution DO NOT connect the Spot LXi AC power adapter to the UUT power
connection port. This will result in damage to the UUT, AC power adapter, or the
Battery Simulator power supply.
4. Turn on the Power Supply.
Note
All tests and verification in this procedure require battery voltage input adjusted to
6.5V DC; Except as called out in the Voltage Calibration section.
Battery Removal / Power Shutdown
Removal of the UUT battery, or power shutdown of the Battery Simulator external power
supply, will require reset of the date and time prior to any further testing, calibration, or
verification activities.
Time & Date Reset:
1. Power on the UUT in configuration mode by pressing the Check and Power On
buttons on the UUT. Hold the Check button until the UUT beeps twice. The UUT
screen displays any POST errors detected.
Figure 4. POST Errors Detected
2. Click the Check button on the UUT. The Configuration Menu opens.
3. Scroll to Date/Time on the UUT Configuration Menu and select.
54
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 5. Date/Time Menu
4. Scroll to Date on the UUT and select. Using the navigation keys, adjust the correct
date and select. Scroll to Time and select. Using navigation keys, adjust the correct
time and select.
Figure 6. Set Date, Set Time
5. Scroll to Exit and select.
Service Manual
Calibration and Verification
55
Figure 7. Exit Menu
6. Reset the UUT using the power button. Do NOT turn off the power supply. The next
power up of the UUT screen displays the correct date and time without errors.
Voltage Calibration
1. Remove the battery from the UUT. Connect the UTT to a Battery Simulator with the
external power supply set to 6.5 +/- 0.1V DC. (Follow the steps in “Power Supply Test
Setup” on page 52.)
2. Connect the service PC running the Spot Lxi Service Tool to the UUT with the USB
Cable. Open the Spot LXi Service tool from the PC.
3. Power on the UUT in configuration mode by pressing the Check and Power On
buttons on the UUT. Hold the Check button until the UUT beeps twice.
56
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 8. Configuration Menu
4. Verify the power supply is at 6.5 +/- 0.1V DC at the battery connector simulator leads.
5. Verify that the UUT is connected and communicating with Spot Lxi Service Tool.
Select Unit > Information. The Unit information window opens. Click OK to close.
6. Select Calibrate > Voltage on the service computer. The UUT screen goes blank.
Figure 9. Calibrate Voltage
7. Carefully adjust the power supply to 5.5 + 0.1V DC at the battery connector simulator
leads. A fine voltage adjustment will be needed to make this adjustment.
Service Manual
Calibration and Verification
Note
57
Do not adjust power supply below 5.5V DC or the UUT will go into shutdown
mode.
8. Read the voltage on the DMM that is connected to the battery simulator leads.
9. Enter this voltage reading into the Actual Voltage field and click the Calibration
button.
10. Click the OK button to accept the inputs. Click Yes to make the changes permanent.
11. Enter your initials in the Calibration Signature field and click OK. The UUT resets and
powers up in normal mode.
Figure 10. Calibration Signature Field
Note
After “Reset” and power up, the UUT detects the low 5.5V DC supply setting and
goes into auto shutdown. Adjust power back to 6.5V DC.
Pressure verification test
Spot LXi devices require annual calibration.
Note
If this is a new NIBP board, go to “NIBP board Initialization” on page 62 and
carefully follow the instructions to initialize this board.
1. Connect the UUT to the pneumatic test assembly using the two-tube blood pressure
hose with the Y-fitting.
Figure 11. Blood Pressure Hose with Y-fitting
2. Connect the test volume hose to the 500cc cylinder.
58
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
3. Power on the UUT in configuration mode by pressing the Check and Power On
buttons on the UUT. Hold the Check button until the UUT beeps twice. The
configuration screen displays.
Figure 12. Configuration Menu
Scroll to Blood Pressure and select it
Figure 13. Blood Pressure Menu
Select BP Calibration Check.
Service Manual
Calibration and Verification
59
Figure 14. BP Calibration Check
4. Open the Spot LXi Service Tool on the service computer and select Test >
Calibration. A Test Calibration box displays on the screen.
Figure 15. Test Calibration with Open Valve
5. Verify the pressure is at or near zero and the voltage is within 0.2V DC of the power
supply (6.5V DC). Verify the valve status is open and the pump status is off.
6. Select Close Valve on the UUT. The valve status changes to closed.
60
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 16. BP Calibration Check Close Valve
Figure 17. Test Calibration with Closed Valve
7. Select Start Cuff Inflation. The pump starts inflating the cuff. Verify the pump status
is on and the pressure is rising.
Service Manual
Calibration and Verification
61
Figure 18. Start Cuff Inflation
8. Inflate the pressure up to 250 mmHg. Select the Stop Pump on the UUT to stop the
inflation. Fine tune the pressure reading to 250 mmHg with the squeeze bulb.
Figure 19. Fine Tune the Pressure Reading to 250 mmHg
9. Check the reading on the pressure meter against reading on the UUT.
a.
Verify the pressure on the UUT is within the pressure tolerance in the table. Use
the squeeze bulb to fine tune the pressure at each inflation pressure limit. If the
pressure is within tolerance, go to the next inflation pressure.
62
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Inflation pressure Pressure tolerance
Inflation pressure Pressure tolerance
250 mmHg +/- 2.0 mmHg
50 mmHg +/- 1.0 mmHg
150 mmHg +/- 1.5 mmHg
0 mmHg +/- 1.0 mmHg
b. If all readings are within specification, go to “Functional tests” on page 67.
c.
If the UUT is not within the pressure tolerance, open the valve to bleed pressure
to zero. Select Calibrate > Pressure on the repair software. Proceed to “Blood
pressure calibration” on page 63. UUT needs calibration.
d. If replacement of the NIBP board is required, first proceed to “NIBP board
Initialization” on page 62 and then proceed to “Blood pressure calibration” on
page 63.
Blood pressure calibration
Note
Complete the voltage calibration before beginning a blood pressure calibration.
If all readings were within specifications during “Pressure verification test” on page 57,
skip this section and go to “Functional tests” on page 67.
NIBP board Initialization
Note
All New NIBP Boards must be initialized before calibration.
1. Power on the UUT in configuration mode by pressing the Check and Power On
buttons on the UUT. Hold the Check button until the UUT beeps twice. The
configuration screen displays.
Figure 20. Configuration Menu
Service Manual
Calibration and Verification
63
2. Open the Spot LXi Service Tool on the service computer and select Calibrate > Reset
Defaults. The Reset Defaults window displays.
Figure 21. Reset Defaults Window
3. Click Reset > Initialize > OK. The NIBP board is initialized.
4. Perform the “Voltage Calibration” on page 55 before proceeding to “Blood pressure
calibration”.
Blood pressure calibration
1. Power on the UUT in configuration mode by pressing the Check and Power On
buttons on the UUT. Hold the Check button until the UUT beeps twice.
Figure 22. Blood Pressure Menu
64
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
2. The configuration screen displays, scroll to Blood Pressure and select it. Select BP
Calibration Check.
Figure 23. BP Calibration Check
3. Open the Spot LXi Service Tool on the service computer and select Calibrate >
Pressure. The Calibrate Pressure window opens.
Figure 24. Calibrate Pressure Window
Service Manual
Calibration and Verification
65
4. Connect the UUT to the pneumatic test assembly using the two-tube blood pressure
hose with the Y-fitting. (See “Blood Pressure Hose with Y-fitting” on page 57.)
5. Connect the pneumatic test assembly hose to the 500cc cylinder of the test volume
and verify the following:
•
the pressure is at zero mmHg,
•
the bleed screw on squeeze bulb is closed,
•
valve on UUT is in the open state.
6. On the Spot LXi Service Tool select Calibrate Zero button.
7. Close Valve on the UUT and use the squeeze bulb to manually inflate the UUT to 200
mmHg. Let stabilize.
Figure 25. Fine Tune the Pressure Reading to 200 mmHg
8. Enter the pressure meter reading in the Calibration Gain field on the service
computer. Be as precise as possible. If pressure meter has resolution of 1.00 mmHg
make sure it reads 200.00 without switching to 199.00 or 201.00. Enter 200.00 in
Calibration Gain field.
66
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 26. Calibration Gain Field
9. Click Calibrate Gain on the service computer.
10. Click OK to accept the inputs. Click Yes to make the changes permanent.
11. Enter your initials in the Calibration Signature field and click OK. The UUT resets and
powers up in normal mode.
Figure 27. Calibration Signature Field
12. Blood Pressure calibration is complete.
Service Manual
Calibration and Verification
67
Functional tests
Note
Perform the Functional Tests sequentially. Fill out the“Service Work Checklist” on
page 111 with the Calibration and Functional Test data obtained as you perform
these steps.
Each test is software driven. Selecting the Test button begins the test.
Connect the correct Test Volume cylinder called out in the procedure (in
parenthesis below) or the test will fail.
Test specification details:
Leak test
6mm maximum in 15 seconds with a volume of (100cc) at 250 mmHg
Dump test
From 260 to less than 15 mmHg in 10 seconds or less with a volume of (500 cc)
Inflation test
From 5 to 210 mmHg in 7 seconds or less with a volume of (250 cc)
Valve control test
From 160 mmHg with a volume of (100 cc)
Open the valve for the following time intervals and pressure drops:
•10 msec = 4 to 12 mmHg
•15 msec = 4 to 15 mmHg
•25 msec = 4 to 25 mmHg
Inflation linearity
Connect a standard cuff hose between the UUT and
the 500cc Linearity input on the Test Volume and inflate.
•Measure the pressure at 6, 9, and 12 seconds and compare to the expected readings at
these intervals.
•Also check the noise level at 7, 10, and 13 seconds into the inflation step.
Functional test steps:
1. If the UUT is connected to the Battery Simulator, set the external power supply to 6.5
+/- 0.1V DC.
Note
The Spot LXi AC power adapter should NOT be connected to the UUT.
If the UUT is NOT connected to the battery simulator, connect the Spot LXi AC
power adapter to the UUT.
2. Power on UUT in normal mode.
3. Connect the UUT to the pneumatic test assembly using the two-tube blood pressure
hose with the Y-fitting. (See “Blood Pressure Hose with Y-fitting” on page 57.) Verify
that the bleed valve on the squeeze ball is closed.
4. Open the Spot LXi Service Tool on the service computer and select Test >
Pneumatics. The Test Pneumatics window opens.
68
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 28. Test Pneumatics Window
a.
Connect the test specific cylinder in parenthesis; (100cc), (500cc), (250cc)
b. Sequentiallyselecteachpneumatictest,startingwith“Leak(100cc)”.ClickTest.
A successful test will display “Passed”.
Figure 29. Passed Leak Test
c.
Perform each of the tests listed after connecting the test specific cylinder. The
“Inflation Linearity (Cuff)” test may use the 500cc cylinder in place of the adult
cuff.
Service Manual
Calibration and Verification
69
Figure 30. Inflation Linearity Cuff Test
Figure 31. Inflation Linearity 500cc Cylinder
100 CC
500 CC
LINEARITY
250 CC
500 CC
d. Click OK after completing the last test to close the Pneumatics test window.
5. On the Spot LXi Service Tool select Test > Current Levels. Perform the tests listed.
The Test Current Levels window opens.
70
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 32. Test Current Levels Window
a.
Sleep State > Test, screen is off and the UUT is idle. Verify that the current is less
than 500 mA. Click OK after completing the measurement.
Figure 33. Sleep State
b. Valve/pump Mode > Test, the UUT is fully active with the valve closed and the
pump running. Verify that the current is less than 2.0 amperes in this state. Click
OK after completing the measurement.
c.
Normal Mode; screen is lit, but the UUT is inactive. The UUT current draw is less
than 1.25 amperes in this state.
d. Click OK after completing the last test to close the Test Current Levels window.
6. On the Spot LXi Service Tool select Test > Noise Levels > Test. The Test Noise
Levels window opens.
Service Manual
Calibration and Verification
71
Figure 34. Test Noise Levels Window
a.
The Test Noise Levels test measures the amount of noise on the UUT A-D
pressure channel. The sample is 1 second in length with 0 mmHg applied. The
maximum allowed noise is .050 mmHg.
b. Click OK after completing the test to close the Test Noise Levels window.
7. On the Spot LXi Service Tool select Test > Buttons. The Test Buttons window opens.
Figure 35. Test Buttons
a.
Press each button on the UUT and verify the appropriate button lights on the Spot
LXi Service Tool window.
72
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 36. UUT Buttons
b. Click OK after completing the test to close the Buttons Test window.
8. On the Spot LXi Service Tool select Test > Interface. The Test Interface window
opens.
Figure 37. Test Interface Window
a.
Perform all commands in this test, verifying the screen on the UUT responds
correctly with each command:
Normal
All On
All Off
Test Pattern
Backlight On/Off, = blank dark UUT display screen
Service Manual
Calibration and Verification
Power Indicator On/Off
Charge Indicator On/Off
Enunciator On/Off, Toggles enunciator tone on and off.
Figure 38. Normal
Figure 39. All On
73
74
Calibration and Verification
Figure 40. All Off
Figure 41. Test Pattern
Welch Allyn Spot Vital Signs LXi
Service Manual
Calibration and Verification
Figure 42. Backlight On/Off
Figure 43. Power Indicator On/Off
Figure 44. Charge Indicator On/Off
b. Click OK after completing the tests to close the Test Interface window.
To perform the over pressure test:
1. Verify that the UUT is in normal mode.
2. Re-install the pneumatic test assembly with the 250cc cylinder connected.
3. On the Spot LXi Service Tool select Unit >Status. A Unit Status window displays.
75
76
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 45. Unit Status Window
4. Check the Log Status Information box in the lower right hand corner of the Spot LXi
Service Tool. The Event logs display in rapid succession.
5. Immediately initiate a blood pressure reading. As the pressure increases, start
applying additional pressure with the squeeze bulb.
6. Increase the pressure to the UUT until an E10 error displays.
7. Uncheck the Log Status Information box and click OK after completing the test to
close the Unit Status box.
Scroll through the event log to locate the last ‘no’ answer, directly followed by the
first ‘yes’ answer in the column labeled over pressure.
Service Manual
Calibration and Verification
77
Figure 46. Event Log
8. Scroll to the right to see the mmHg pressure that these events occurred.
9. Select the higher pressure reading when the E10 error occurred. Verify the pressure is
between 296 and 329 mmHg.
Note
The following tests are for verification only. There is no updating of calibration
parameters.
Temperature Functional Check
Temperature test setup
The 9600 Plus Calibration Tester takes approximately 20 minutes to heat to the lowest
setting. When testing several thermometers at all three temperatures, it is recommended
to test all probes at one Calibration Set Point Temperature before proceeding to the next
Calibration Set Point Temperature.
78
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
To further expedite testing start at the lowest Calibration Set Point Temperature. The 9600
Plus Calibration Tester does not have an internal fan, this causes a longer cool down time
than warm up time.
Refer to the 9600 Plus Calibration Tester Directions for Use manual for specific
information regarding the LCD window or the control buttons.
1. Choose the proper mains plug insert and slide it over the two prongs in the power
converter.
Figure 47. Power Adapter and Mains Plug Inserts
Two prongs in the
power adapter
11.8593./AUS
11.8593./US
11.8593./EU
11.8593./UK
(US)
US
(UK)
UK
(AUS)
AUS
(EU)
EU
2. Plug the power adapter into the 9600 Plus Calibration Tester and the opposite end
into a wall outlet.
3. Place the 9600 Plus Calibration Tester on a level surface away from sunlight, drafts,
and other sources of heat or cold.
4. Observe the Set Point Mode in the upper left hand corner of the LCD display. If the
unit displays a “D”, it is in Default Mode and will heat to the lowest Set Point
Temperature. If you do not want to conduct testing at this Set Point Temperature,
press and hold the Temperature Selection button to select the desired setting. The
temperature display will flash before staying on continuously to indicate the 9600 Plus
Calibration Tester has stabilized and is ready for use.
Changing the Calibration Set Point Temperature on the 9600 Plus
Calibration Tester
To scroll from one set point to the next, press and hold the Temperature Selection
button (up/down button) until a beep is heard. The newly selected set point appears in the
upper left corner of the LCD display. The device's current temperature is displayed, starts
to flash, and continues flashing until the cavity reaches the equilibrium at the new set
point.
Welch Allyn SureTemp Plus Thermometers
Caution Store thermometers for testing in the same room as the 9600 Plus
Calibration Tester for approximately 30 minutes prior to testing to allow for
thermal accommodation.
Service Manual
Calibration and Verification
79
To begin functional verification of the SureTemp Plus thermometer:
1. Verify that the UUT is ON and is operating in normal mode.
2. Remove the thermometer probe from the probe well and clean it with either a 70%
isopropyl alcohol solution, or a 10% chlorine bleach solution. Let the thermometer air
dry. Do not apply a probe cover.
3. Verify that the blue (oral) probe well is in place.
Insert the thermometer into the 9600 Plus Calibration Tester device thermistor
device port (small port).
Figure 48. 9600 Plus Calibration Tester with the Welch Allyn SureTemp Plus Thermometer
4. Verify that the thermometer enters Monitor Mode, (approximately one minute), the
snail symbol and “Monitor” are displayed on the UUT display.
Figure 49. Temperature Monitor Mode
5. After the UUT enters “Monitor” mode wait for approximately one minute or until the
temperature on the thermometer is stable for ten seconds.
a.
Verify that the UUT thermometer's temperature reading is within the temperature
tolerance in the table.
Calibration Set Point Temperature
Temperature tolerance
96.8°F (36.0°C)
+/- 0.2°F (+/- 0.1°C)
105.8°F (41.0°C)
+/- 0.2°F (+/- 0.1°C)
80
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
b. When verifying several UUT thermometers at both temperatures, it is
recommended to verify all UUT thermometers at one Calibration Set Point
Temperature before proceeding to the next Calibration Set Point Temperature.
c.
Changing the Calibration Set Point Temperature (9600 Plus Calibration Tester):
To scroll from one set point to the next, press and hold the Temperature
Selection button (up/down button) until a beep is heard. The newly selected
set point appears in the upper left corner of the LCD display. The device's
current temperature is displayed, starts to flash, and continues flashing until
the cavity reaches the equilibrium at the new set point.
To begin functional verification of SureTemp Plus without thermometer (Optional):
If the UUT fails the temperature verification using the SureTemp Plus thermometer; then
perform this separate functional test of the UUT temperature circuitry.
1. Remove probe and probe well completely.
2. Insert calibration key (part number 06138-000) and replace probe well.
Figure 50. Calibration Key and Probe Well
3. Insert and then remove probe from probe storage channel to reset thermometer.
Service Manual
Calibration and Verification
81
Figure 51. Reset Thermometer
4. Wait for display test, and then observe display.
5. Display should read 36.3°C +/- 0.1°C or 97.3°F +/- 0.2°F.
Figure 52. Temperature Display in F°
6. Remove calibration key and install probe well.
7. If the UUT temperature circuitry verified successfully and the temperature verification
failed using thermometer probe; then replace SureTemp Plus thermometer probe.
82
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Braun ThermoScan Pro 4000
Caution Store thermometers for testing in the same room as the 9600 Plus
Calibration Tester for approximately 30 minutes prior to testing to allow for
thermal accommodation.
To begin functional verification of the Braun ThermoScan PRO 4000 thermometer:
1. Clean the probe tip with a cotton swab slightly moistened with isopropyl alcohol,
remove excess alcohol with a clean cotton swab, and let air dry for 5 minutes.Do not
use any chemical other than alcohol to clean the probe window.
2. Place the Braun ThermoScan Pro 4000 in Calibration Mode using the following steps.
a.
Push and release the I/O mem button to turn the product on. The display shows
symbols and functions. The Braun ThermoScan Pro 4000 performs an automatic
self check. After a few seconds you hear a beep and see two dashed lines, a
sound symbol, and ° C or ° F on the display.
Figure 53. Braun Self Check
b. Push the I/O mem button again and keep it pressed for the following steps:
•
After approx. 3 seconds the “OFF” symbol flashes on the display (keep
pressing the button).
•
When you hear a beep, release the button immediately.
•
The Braun TheromScan Pro 4000 is now in calibration check mode and the
display is flashing and showing the “CAL” symbol.
•
Apply a new probe cover. Insert the Braun ThermoScan Pro 4000 into the
9600 Plus Calibration Tester ear device port (large port). Place the probe
firmly into the ear device port.
Service Manual
Calibration and Verification
Figure 54. Braun Ear Device Port
3. Wait approximately three seconds, press the thermometer start button, and watch
for the “Exac Temp” light to flash.
Figure 55. Press Start Button
83
84
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
4. Leave the thermometer in the 9600 Plus Calibration Tester until you hear a beep.
Remove the Pro 4000 Thermometer from the 9600 Plus Calibration Tester and read
the temperature in the thermometer’s display.
a.
Verify that the UUT thermometer's temperature reading is within the temperature
tolerance in the table.
Calibration Set Point Temperature
Temperature tolerance
96.8°F (36.0°C)
+/- 0.2°F (+/- 0.1°C)
105.8°F (41.0°C)
+/- 0.2°F (+/- 0.1°C)
b. Wait one full minute before taking another reading with the same thermometer.
Repeated measurements in short sequence may cause higher readings.
c.
When verifying several UUT thermometers at both temperatures, it is
recommended to verify all UUT thermometers at one Calibration Set Point
Temperature before proceeding to the next Calibration Set Point Temperature.
d. Changing the Calibration Set Point Temperature (9600 Plus Calibration Tester):
To scroll from one set point to the next, press and hold the Temperature
Selection button (up/down button) until a beep is heard. The newly selected
set point appears in the upper left corner of the LCD display. The device's
current temperature is displayed, starts to flash, and continues flashing until
the cavity reaches the equilibrium at the new set point.
5. The Braun ThermoScan PRO 4000 thermometer will exit CAL mode after four
minutes.
To begin functional verification of the Braun ThermoScan PRO 4000 thermometer
Down Load:
1. Clean the probe tip with a cotton swab slightly moistened with isopropyl alcohol,
remove excess alcohol with a clean cotton swab, and let air dry for 5 minutes. Do not
use any chemical other than alcohol to clean the probe window.
2. Insert the Braun ThermoScan PRO 4000 thermometer into the UUT and wait for the
“Exac Temp” light to go out.
Service Manual
Calibration and Verification
85
Figure 56. Braun Exac Temp Light
3. Remove the Braun ThermoScan PRO 4000 thermometer from the UUT.
4. Apply a new probe cover. Insert the Braun ThermoScan Pro 4000 into the 9600 Plus
Calibration Tester ear device port (large port). Place the probe firmly into the large
port. See (Figure 54)“Braun Ear Device Port” on page 83. The temperature selection
is non-specific for this particular test.
5. Wait approximately three seconds, press the thermometer Start button, and watch
for the “Exac Temp” light to flash. See “Braun Exac Temp Light”.
6. Leave the thermometer in the 9600 Plus Calibration Tester until you hear a beep.
Remove the Pro 4000 Thermometer from the 9600 Plus Calibration Tester and read
the temperature in the thermometer's display.
7. Insert the Braun ThermoScan PRO 4000 thermometer into the UUT (should be on and
in normal mode). The reading from the Braun ThermoScan PRO 4000 thermometer
should transfer automatically to the UUT display. Verify this action.
Changing the Calibration Set Point Temperature
To scroll from one set point to the next, press and hold the Temperature Selection button
until a beep is heard. The newly selected set point appears in the upper left corner of the
LCD display. The device’s current temperature is displayed, starts to flash, and continues
flashing until the cavity reaches the equilibrium at the new set point.
To begin functional verification of the Masimo SpO2
Use the “Masimo Tester” to verify the Masimo SpO2 functionality.
86
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 57. Masimo Tester
1. With the UUT OFF, orient the Masimo Tester such that the mini-D connector mates
with the SpO2 connector on the UUT; or use appropriate Masimo extension cable to
connect the Masimo Tester and UUT.
2. Power ON the Spot LXi UUT and confirm the SpO2 reading in the Display Window is
81%± 3% and the pulse reading is 61 bpm ± 1 bpm.
Figure 58. SpO2 Reading
3. Place the thumb and index finger on the gray buttons on either side of the Masimo
Tester connector or extension cable connector; press the buttons firmly, and gently
pull to remove the tester.
Service Manual
Calibration and Verification
Note
87
The functionality of the SpO2 module is not adjustable. If the SpO2 is not
functioning properly, or the SpO2 and pulse performance cannot be verified
against the calibrated simulator, contact Welch Allyn Technical Support page iv.
To begin functional verification of the Nellcor SpO2
Use a Nellcor-approved SpO2 simulator (SRC-MAX) to verify the Nellcor SpO2
functionality.
Figure 59. Nellcor SpO2 Simulator
1. With the UUT ON and completely booted, orient the simulator such that the
connector mates with the SpO2 connector on the UUT; or use appropriate Nellcor
extension cable to connect the simulator and UUT.
Note
The UUT MUST be powered on prior to connecting the Nellcor SpO2 simulator.
2. On the Nellcor simulator change the SpO2 percentage from default 75% to 90%.
3. Confirm the SpO2 reading in the Display Window is 90%± 1% and the pulse reading
is 60 bpm ± 1 bpm.
88
Calibration and Verification
Welch Allyn Spot Vital Signs LXi
Figure 60. SpO2 Reading and Pulse Reading
4. Remove the simulator by placing the thumb and index finger on either side of the
simulator connector or extension cable connector; press the buttons firmly and gently
pull to remove.
Note
The functionality of the SpO2 module is not adjustable. If the SpO2 is not
functioning properly, or the SpO2 and pulse performance cannot be verified
against the calibrated simulator, contact Welch Allyn Technical Support page iv
89
7
Specifications
Performance
This section describes normal ranges for Spot Vital Signs LXi.
Blood Pressure Accuracy
Blood pressure accuracy meets or exceeds AAMI SP10:2002 standards for non-invasive
blood pressure accuracy (± 5 mmHg mean error, 8 mmHg standard deviation). Blood
pressure accuracy is validated for pressure measurement using the upper arm only.
Cuff Pressure Range
0 to 300 mmHg
Systolic Range
60 to 250 mmHg
Diastolic Range
30 to 160 mmHg
Blood Pressure Determination Time
Typical: 15 seconds
Mean Arterial Pressure Range
40 to 190 mmHg
Pulse Rate Range
(using SpO2 determination)
25 to 240 bpm
Pulse Rate Range
(using Blood Pressure determination)
35 to 199 bpm
Pulse Rate Accuracy (using SpO2
determination)
Without Motion: 25 to 245 bpm ± 3 digits1
With Motion: normal physiologic range (55 to 125 bpm) ± 5 digits
Low Perfusion: 25 to 245 bpm ± 3 digits1
Pulse Rate Accuracy
(using Blood Pressure determination)
Overpressure Cutoff
1 Specification applies to device performance and was validated with Biotek and Nellcor simulators.
±5.0%
315 mmHg ±15 mmHg
90
Specifications
Welch Allyn Spot Vital Signs LXi
Temperature Specifications
Temperature Range
SureTemp Plus
Braun ThermoScan PRO 4000
Calibration Accuracy
SureTemp Plus
Braun ThermoScan PRO 4000 for displayed
temperature ranges
Display Resolution
SureTemp Plus Predict Time
Oral
Adult Axillary
Pediatric Axillary
Rectal
80° to 110° F (26.7° to 43.3° C)
68° to 108° F (20° to 42.2° C)
±0.2° F (0.1° C) (Monitor Mode)
± 0.4° F (±0.2° C) 95.9° to 107.6° F (35.5° to 42° C)
±0.5° F (±0.25° C) (outside this temperature range)
0.1° F or ° C
Approx. 4 to 6 seconds
Approx. 12 to 15 seconds (age 18 years and older)
Approx. 10 to 13 seconds (age 17 years and younger)
Approx. 10 to 13 seconds
Service Manual
Specifications
91
SpO2 Specifications
Masimo Sensor Accuracy Guide
Accuracy specified when used with Masimo SET pulse oximetry monitors or with
licensed Masimo SET pulse oximetry modules using PC series patient cables, during no
motion. Numbers present ± 1 standard deviation. Plus or minus one standard deviation
represents 68% of the population. SpO2 accuracy from 70% to 100%. Pulse rate
accuracy from 25 to 240 bpm.
Performance Measurement Range
SpO2: 1 to 100%
Pulse Rate: 25 - 240 beats per minute (BPM)
Perfusion
0.02% to 20%
Accuracy
Saturation: 70% to 100%
No Motion: Adults, Pediatrics ± 2 digits
Neonates ± 3 digits
Motion: Adults, Pediatrics ± 3 digits
Neonates ± 3 digits
Low Perfusion: Adults, Pediatrics ± 2 digits
Neonates ± 3 digits
Pulse Rate Accuracy
Pulse Rate: 25 to 250 bpm
No Motion: Adults, Pediatrics, Neonates ± 3 digits
Motion: Adults, Pediatrics, Neonates ± 5 digits
Low Perfusion: Adults, Pediatrics, Neonates ± 5 digits
Table 1. Masimo Sensor Accuracy Guide
Saturation Accuracy
Sensor
Pulse Rate Accuracy
Weight Range
No Motion
Motion
No Motion
Motion
LNOP-ADT
> 30 kg
± 2%
± 3%
± 3 bpm
± 5 bpm
LNOP-PDT
10 to 50 kg
± 2%
± 3%
± 3 bpm
± 5 bpm
LNOP-NEO
< 10 kg
± 3%
± 3%
± 3 bpm
± 5 bpm
LNOP-NEOPT
< 1 kg
± 3%
± 3%
± 3 bpm
± 5 bpm
LNOP-DCI
> 30 kg
± 2%
± 3%
± 3 bpm
± 5 bpm
LNOP-DCIP
10 to 50 kg
± 2%
± 3%
± 3 bpm
± 5 bpm
Masimo Patents
The Masimo sensors and cables are covered under one or more of the following U.S.A.
patents: 5,758,644; 5,823,950; 6,011,986; 6,157,850; 6,263,222; 6,501,975; and other
applicable patents listed at www.masimo.com/patents.htm.
92
Specifications
Welch Allyn Spot Vital Signs LXi
Nellcor Sensor Accuracy Guide
Accuracy specifications are based on controlled hypoxia studies with healthy,
non-smoking adult volunteers over the specified saturation SpO2 range. Pulse oximeter
SpO2 readings were compared to SaO2 values of drawn blood samples measured by
hemoximetry. All accuracies are expressed as + “X” digits. This variation equals + one
standard deviation (+ 1 SD), which encompasses 68% of the population.
Table 2. OxiMax Sensor Models, Single Patient Use
Sensor Models
SpO2 Range
70% to 100%
MAX-AI1
±2
MAX-PI*
±2
MAX-II
±2
MAX-RI
2
± 3.5
1 The accuracy specification under motion conditions is ± 3. For a definition of motion, contact Nellcor
Technical Services or your local Nellcor representative.
2 The accuracy specification has been determined between saturations of 80% to 100%.
Table 3. OxiCliq Sensor Models, Single Patient Use
Sensor Models
OXICLIQ-PI
SpO2 Range
70% to 100%
± 2.5
Table 4. Reusable Sensor Models
Sensor Models
D-YS (Infant to Adult)
SpO2 Range
70% to 100%
±3
D-YS and D-YSE
± 3.5
D-YS and D-YSPD
± 3.5
DS-100A
±3
OXI-A/N (Adult/neonate)
Adult: ± 3
Neonate: ± 4
OXI-P/I (Pediatric/infant)
±3
Nellcor Patents
Covered by one or more of the following U.S. patents and foreign equivalents:
5,485,847; 5,676,141; 5,743,263; 6,035,223; 6,226,539; 6,411,833; 6,463,310; 6,591,123;
6,708,049; 7,016,715; 7,039,538; 7,120,479; 7,120,480; 7,142,142; 7,162,288; 7,190,985;
7,194,293; 7,209,774; 7,212,847; 7,400,919.
Service Manual
Specifications
93
Mechanical
Dimensions
Height: 10.63“ (27 cm)
Length/Braun: 8” (20.32 cm)
Length/SureTemp Plus: 7.5” (19 cm)
Depth: 5.25” (13.34 cm)
Weight
7.5 lbs (3.4 kg)
Mounting
Portability
Self-supporting on rubber feet
Custom mobile stand
Custom wall mount
May be hand-carried when held by the rear handle
Electrical
Power Requirements
Patient-rated isolation transformer is connected to AC mains:
100-240V, 50-60Hz, 0.4A or internal power: 6Vdc, 6Ah
Patents
For patent information, please visit www.welchallyn.com/patents
Batteries
Spot Vital Signs LXi
Braun ThermoScan PRO 4000 thermometer
External Printer
Sealed Lead Acid Battery (4500-84)
with external charger (4500-101A)
Rechargeable Battery Pack (53020-0000)
Ni-Mh Rechargable Battery Pack (4500-505)
Includes a separate charger (713703 or BC1300M)
•
The Spot Vital Signs LXi battery is 90 to 100% charged after 6 hours of charging. The
Spot LXi battery automatically charges when Spot LXi is powered through the AC
power transformer. An operator can use the device while the battery is charging;
however, the battery charges faster when the instrument is not in operation.
•
The rechargeable batteries in the Braun ThermoScan PRO 4000 thermometer require
an additional 1 hour to charge.
•
Charge the external printer battery 9 hours before initial use.
Environmental
WARNING This device is not suitable for use in the presence of a flammable
anesthetic mixture with air or oxygen or nitrous oxide. An explosion may result.
94
Specifications
Welch Allyn Spot Vital Signs LXi
Operating Temperature
Storage/Transport Temperature
50° to 104° F (10° to 40° C)
Device with SureTemp Plus: -13 to 131F (-25 to 55C)
Device with Braun ThermoScan PRO 4000: -4 to 122F (-20 to 50C)
Relative Humidity
15 to 95% (non-condensing)
Operating Altitude
-557 to 16,000 ft. (-170 to 4877 m)
Radio
Mechanical
Dimensions
3.93” L x 2.38” W x 1.42” T
99.78mm L x 60.5 mm W x 36.1mm T
Mounting
Nylon Bracket
Operating Temperature
-40° C to +85° C
Storage Temperature
-40° C to +125° C
Configuration Options
DHCP Enabled or
Not
If not DHCP:
• IP Address
• Subnet Address
• Default
Gateway
Address
• Primary DNS
Encryption
Wireless Security
Mode
Disabled
WEP 64-bit WEP 128-bit
WPA2 Security
CCMP
(WPA2-PSK and
WPA2-AES only)
CCMP and TKIP
EAP Settings
EAP Type
(WPA2-AES only)
TLS
Channel
Default WEP
Key 1-4
SSID
WEP Authentication
WPA Pass
Phrase
WPA2 Pass
Phrase
PSK Format
Hexadecimal
ASCII
TTLS
WPA2-PSK
WPA2-AES
PEAP
Auto
Service Manual
Specifications
95
Guidance and Manufacturer’s Declaration For Spot Vital
Signs LXi Radio
Emissions and Immunity Information
Electromagnetic Emissions
The Spot Vital Signs LXi is intended for use in the electromagnetic environment specified below. The customer or user of the Spot Vital Signs
LXi should assure that it is used in such an environment.
Emissions Test
Compliance
Electromagnetic Environment - Guidance
RF emissions
Group 1
The Spot Vital Signs LXi uses RF energy only for its internal function. Therefore, its RF
emissions are very low and are not likely to cause any interference in nearby electronic
equipment.
Class B
The Spot Vital Signs LXi is suitable for use in all establishments, including domestic
establishments and those directly connected to the public low-voltage
power supply network that supplies buildings used for domestic purposes.
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
Class A
IEC 61000-3-2
Voltage fluctuations/
flicker emissions
Complies
IEC 61000-3-3
Electromagnetic Immunity
The Spot Vital Signs LXi is intended for use in the electromagnetic environment specified below. The customer or user of the Spot Vital Signs
LXi should assure that it is used in such an environment.
Immunity Test
IEC 60601
Test Level
Compliance Level
Electromagnetic Environment - Guidance
Electrostatic discharge
(ESD)
± 6 kV contact
± 6 kV contact
± 8 kV air
± 8 kV air
Floors should be wood, concrete, or ceramic tile. If floors are
covered with synthetic material, the relative humidity should
be at least 30%.
Electrical fast transient/ ±2 kV for power supply
burst
lines
±2 kV for power supply
lines
Mains power quality should be that of a typical commercial or
hospital environment.
IEC 61000-4-4
±1 kV for input/output
lines
±1 kV for input/output
lines
Surge
±1 kV differential mode
±1 kV differential mode
IEC 61000-4-5
±2 kV common mode
±2 kV common mode
IEC 61000-4-2
Mains power quality should be that of a typical commercial or
hospital environment.
96
Specifications
Welch Allyn Spot Vital Signs LXi
Voltage dips, short
interruptions, and
voltage variations on
power supply input
lines.
>95% dip in 0.5 cycle
>95% dip in 0.5 cycle
60% dip in 5 cycles
60% dip in 5 cycles
30% dip for 25 cycles
30% dip for 25 cycles
IEC 61000-4-11
>95% dip in 5 seconds
>95% dip in 5 seconds
Power frequency
(50/60Hz)
magnetic field
3 A/m
3 A/m
Mains power quality should be that of a typical commercial or
hospital environment. If the user of the Spot Vital Signs LXi
requires continued operation during power mains
interruptions, it is recommended that the Spot Vital Signs LXi
be powered from an uninterruptible power supply or battery.
Power frequency magnetic fields should be at levels
characteristic of a typical location in a typical commercial or
hospital environment.
IEC 61000-4-8
Electromagnetic Immunity
The Spot Vital Signs LXi is intended for use in the electromagnetic environment specified below. The customer or user of the Spot Vital Signs
LXi should assure that it is used in such an environment.
Immunity Test
IEC 60601
Test Level
Compliance Electromagnetic Environment - Guidance
Level
Portable and mobile RF communications equipment should be used no closer
to any part of the Spot Vital Signs LXi, including cables, than the
recommended separation distance calculated from the equation applicable
to the frequency of the transmitter.
Recommended separation distance
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to 80 MHz
3 Vrms
d = (1.17) P
Radiated RF
IEC 61000-4-3
3 V/m
80 MHz to 2.5 GHz
3 V/m
d = (1.17) P 80 MHz to 800 MHz
d = (2.33) P 800 MHz to 2.5 GHz
where P is the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer and d is the recommended
separation distance in metres (m).
Field strengths from fixed RF transmitters, as determined by an
electromagnetic site survey,a should be less than the compliance level in
each frequency range.b
Interference may occur in the vicinity of equipment marked with the
following symbol:
Note 1: At 80 MHz and 800 MHz, the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures,
objects, and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio,
AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due
to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the Spot
Vital Signs LXi is used exceeds the applicable RF compliance level above, the electrocardiograph should be observed to verify normal operation.
If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the electrocardiograph.
b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Service Manual
Specifications
97
Recommended Separation Distances Between Portable and Mobile RF Communications Equipment and the Spot Vital Signs LXi
The Spot Vital Signs LXi is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer
or user of the Spot Vital Signs LXi can help prevent electromagnetic interference by maintaining a minimum distance between portable and
mobile RF communications equipment (transmitters) and the Spot Vital Signs LXi as recommended below, according to the maximum output
power of the communications equipment.
Separation Distance According to Frequency of Transmitter (m)
Rated Max. Output
Power of Transmitter
(W)
150 kHz to 80 MHz
80 MHz to 800 MHz
800 MHz to 2.5 GHz
d = (1.17) P
d = (1.17) P
d = (2.33) P
0.01
0.117
0.117
0.233
0.1
0.37
0.37
0.74
1
1.17
1.17
2.33
10
3.70
3.70
7.37
100
11.70
11.70
23.30
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated
using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer.
Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures,
objects, and people.
98
Specifications
Welch Allyn Spot Vital Signs LXi
99
8
Troubleshooting
This chapter provides helpful information in troubleshooting the Spot Vital Signs LXi.
Error Codes
The following tables of error codes provide a quick reference of the descriptions and
probable causes of error codes.
Table 1. Informational Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
_n/a
Copyright notice displayed on powers up
splash screen.
_n/a
Message displays when the user attempts Printing is already in progress
to start another print while a print job is
currently printing.
_n/a
Clear current reading.
_n/a
Erase all readings.
_n/a
Information screen telling the user how to Use the navigation keys to edit
operate the location identifier edit menu characters and the SELECT key to stop
in Configuration Mode.
editing.
_n/a
Message displays when Mod F cannot
perform a STEP NIBP measurement and
switches to normal method.
_n/a
Message displays when in MEM mode
and there are no readings to display.
_n/a
External devices configuration menu
message when the user tries to exit the
menu having enabling the information
system, but not that Patient ID.
User must enable the Patient ID if using
the information system.
_n/a
Message displays below txtPIDMsgB.
User must press SELECT and correct the
problem.
_n/a
Information displays when the user
enables device in external devices
configuration menu.
User must connect the Spot Vital Signs
LXi to an external device.
_n/a
Message displays below txtPIDMsgA
User must press SELECT when
completed.
_n/a
Line displays below error/information
message if the user can clear the error/
condition.
User must press ACCEPT to clear.
Restrict patient movement.
100
Troubleshooting
Welch Allyn Spot Vital Signs LXi
Table 1. Informational Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
_n/a
Corrective Action
User decides whether to reset everything
back go factory default values.
_n/a
Error condition occurs causing the unit to Spot Vital Signs LXi will shut down in 1
automatically shut down. The user cannot minute.
clear this message.
_n/a
User confirms to start printing.
Table 2. Blood Pressure Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
10
C01
User abort.
11
C03
Inflation too quick.
Check tubing and connections.
12
E10
Overpressure
Check patient.
13
C04
Major air leak.
Excessive inflation time; check for air
leaks.
14
C05
Excessive arm movement
Excessive noise, check cuff placement;
restrict patient movement.
15
C07
Auto cycle skipped, system busy.
Device will power down.
16
C07
Auto cycle skipped, NIBP reached too
soon.
Device will power down.
17
C02
Auto zero failure.
Auto zero failure; check air obstruction;
limit patient movement.
18
C04
Could not reach target pressure.
Excessive inflation time; check for air
leaks.
19
E20
Missed A/D sample.
General internal malfunction. Call
Technical Support.
20
E20
A/D timeout failure.
General internal malfunction. Call
Technical Support.
NIPB NOT AVAILABLE.
Correct probe tip conditions. If problem
persists, replace probe. If problem still
persists, replace module.
21
Corrective Action
22
E11
Malfunction
User should try another cycle. If problem
persists, replace probe.
23
C06
Reinflation needed.
Measurement was outside of device’s
measurement range.
24
C05
Cycle took too long.
Check cuff placement; restrict patient
movement.
25
C12
Ambient temp out of range.
Check internal temperature at probe well.
Verify ambient temperature does not
exceed operating specification.
26
C13
Battery failure
Battery failure; use wall transformer.
Service Manual
Troubleshooting
101
Table 2. Blood Pressure Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
27
E11
> 10mm residual pressure > minutes.
Verify that the supply voltage is within
specification.
28
E11
>15mm residual pressure >3 mins.
Verify that the supply voltage is within
specification.
29
C02
Couldn’t bleed pressure < 9 mmHg
Auto zero failure, check tubing for kinks
and connection integrity, limit patient
movement.
32
Thermistor pulled away from the tip or
heater broken.
Try another predict cycle. If the problem
persists, replace probe.
33
Probe not responsive. Probe not
characterized/calibrated.
Replace probe.
34
Probe not characterized/calibrated.
Replace probe.
41
C06
Low inflation; first step had largest value, Measurement was outside of Spot Vital
first step’s value > systolic value.
Signs LXi measurement range.
42
C06
Dump too soon; last step had largest
value, next to last step’s value > diastolic
value; will not normally occur in autodump mode.
Check connections; restrict patient
movement.
43
C05
Step too big systolic; difference in
pressure between step above and step
below systolic is too great.
Excessive noise; check cuff placement and
limit movement.
44
C05
Step too big diastolic; difference in
pressure between step above and step
below diastolic is too great.
Excessive noise; check cuff placement and
limit movement.
45
C05
Range error: calculated BP is outside of
measurement range.
Excessive noise; check cuff placement and
limit movement.
46
C05
Pressure reverse systolic; pressure of step Excessive noise; check cuff placement and
above systolic is lower than pressure of
limit movement.
step below systolic.
47
C05
Pressure reverse diastolic; pressure of
Excessive noise; check cuff placement and
step above systolic is lower than pressure limit movement.
of step below diastolic.
48
C05
Step too big MAP; difference in pressure
between adjacent steps near MAP is too
great.
Excessive noise; check cuff placement and
limit movement.
49
C05
Too few steps; less than 5 steps
Excessive noise; check cuff placement and
limit movement.
50
C05
Excessive noise; check cuff placement and
Bad value diastolic; value of step below
diastolic and step below that step are not limit movement.
consistent.
51
C05
Value reverse systolic; value of step above Excessive noise; check cuff placement and
limit movement.
systolic is greater than value of step
below systolic.
52
C05
Excessive noise; check cuff placement and
Value reverse diastolic; value of step
above systolic is greater than value of step limit movement.
below diastolic.
102
Troubleshooting
Welch Allyn Spot Vital Signs LXi
Table 2. Blood Pressure Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
53
C05
No info - can’t be produced by Mod F if
they don’t exist in the code.
Excessive noise; check cuff placement and
limit movement.
54
C05
No info - can’t be produced by Mod F if
they don’t exist in the code.
Excessive noise; check cuff placement and
limit movement.
55
C05
No info - can’t be produced by Mod F if
they don’t exist in the code.
Excessive noise; check cuff placement and
limit movement.
56
C05
Out of memory; deflation contains too
many steps. SW sets allowable limit of
steps that can be stored and used for BP
determination for a given cycle.
Excessive noise; check cuff placement and
limit movement.
57
C05
Retarget error; cycle tried to retarget too
many times. Only one allowed retarget
allowed per cycle.
Excessive noise; check cuff placement and
limit movement.
58
C05
Repump error: Tried to repump too many
times. Limit is set to 3 repumps. This can
occur on a cycle with bad signal to noise
ratio or if a subject’s pulses are so small
that pulses above the diastolic ratio are
not detectable with the lowest allowed
thread threshold.
Excessive noise; check cuff placement and
limit movement.
59
C05
Systolic curve fit error; the steps on the
Excessive noise; check cuff placement and
systolic side of the envelope could not be limit movement.
curve fit. Causes include: too few or too
many steps sent to curve fit routine; math
error in curve fit routine.
60
C05
Diastolic curve fit error; the steps on the Excessive noise; check cuff placement and
systolic side of the envelope could not be limit movement.
curve fit. Causes include: too few or too
many steps sent to curve fit routine; math
error in curve fit routine.
61
C05
Systolic slope error; slope of curve fit of
systolic points has a slope out of range.
Can occur with bad cuff fit, rapidly
changing BP etc.
Excessive noise; check cuff placement and
limit movement.
62
C05
Diastolic slope error; slope of curve fit of
diastolic points has a slope out of range.
Can occur with bad cuff fit, rapidly
changing BP etc.
Excessive noise; check cuff placement and
limit movement.
63
C05
Excessive noise; check cuff placement and
Systolic extrapolation error; the systolic
limit movement.
pressure that is represented by the
systolic ratio is outside of the data sent to
the curve fit routine.
64
C05
Diastolic extrapolation error; the systolic
pressure that is represented by the
diastolic ratio is outside of the data sent
to the curve fit routine.
65
C05
Peak range error; the height of the peak of Excessive noise; check cuff placement and
the envelope is outside normal limits.
limit movement.
66
C05
Reinflation too late.
Excessive noise; check cuff placement and
limit movement.
Excessive noise; check cuff placement and
limit movement.
Service Manual
Troubleshooting
103
Table 2. Blood Pressure Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
67
C06
High heart rate.
Unable to determine blood pressure; pulse
rate may be out-of-range.
68
Err
Too many reinflates.
Restrict patient movement.
69
C06
Problem reading the module's EEPROM or Verify that the supply voltage is correct.
saving to the module’s EEPROM.
Try to make changes. If problem persists,
replace module.
70
C06
Problem reading the probe’s EEPROM.
78
C06
The probe non-volatile error log memory
Measurement was outside of device’s
error detection mechanism detected error. measurement range.
79
C06
The module’s non-volatile error log
memory error detecting mechanism
detected an error.
5600
Err
Invalid ModF algorithm.
5601
Err
Invalid ModF init code.
5602
Err
Invalid ModeF PMode.
5603
Err
Invalid ModF target pressure.
5604
Err
Invalid ModF configuration.
Verify that the supply voltage is correct.
Try to make changes.
Measurement was outside of device’s
measurement range.
Table 3. POST Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
80
E30
FPROM checksum error.
General internal malfunction; contact
Technical Support.
81
E31
RAM test failure.
General internal malfunction; contact
Technical Support.
82
E32
Factory EEprom checksum error.
General internal malfunction; contact
Technical Support.
83
E33
User EEprom checksum error.
General internal malfunction; contact
Technical Support.
84
E34
A/D converter failure.
General internal malfunction; contact
Technical Support.
85
E35
SpO2 module failure.
General internal malfunction; contact
Technical Support.
86
E36
Diatek module failure
General internal malfunction; contact
Technical Support.
87
E37
Printer problem.
General internal malfunction; contact
Technical Support.
88
E38
Real time clock failure.
Date and time not set; see “Set the Date
and Time Configurations” in the
Directions for Use.
104
Troubleshooting
Welch Allyn Spot Vital Signs LXi
Table 3. POST Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
89
E39
No calibration signature.
General internal malfunction; contact
Technical Support.
90
E40
Bad NIBP calibration record.
General internal malfunction; contact
Technical Support.
91
E41
Stepper valve bad.
General internal malfunction; contact
Technical Support.
92
E42
8bit substitute for 16bit errors.
Internal communications error.
Disconnect the battery and wait 5
minutes. Reconnect the battery, and then
see “Set the Date and Time
Configurations” in the Directions for Use.
93
E43
Error log checksum error.
General internal malfunction; contact
Technical Support.
94
Err-E44
POST que full.
General internal malfunction; contact
Technical Support.
95
E44 E45
POST que full.
General internal malfunction; contact
Technical Support.
Table 4. SureTemp Plus Temperature Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
121
E0.4
Probe is over temperature (112° F /
44.4° C).
Correct probe tip conditions. If problem
persists, replace probe.
122
E0.1
Excessive heater energy.
Try another predict cycle. If problem
persists, replace probe.
123
23
Host interface error.
Try another predict cycle. If problem
persists, replace probe.
124
A^!
Device outside operating temperature
range.
Decrease ambient temperature.
125
Av!
Device outside operating temperature
range.
Increase ambient temperature.
126
26
Invalid SureTemp algorithm.
Try another predict cycle. If problem
persists, replace probe.
127
b^
Battery voltage over the algorithm’s
maximum value.
Contact Technical Support.
128
bv
Battery voltage under the algorithm’s
minimum value.
Contact Technical Support.
129
29
Battery voltage not set.
Try another predict cycle. If problem
persists, replace probe.
130
30
Prediction algorithm not set.
Try another predict cycle. If problem
persists, replace probe.
131
31
Ambient temperature not set.
Try another predict cycle. If problem
persists, replace probe.
Service Manual
Troubleshooting
105
Table 4. SureTemp Plus Temperature Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
132
E0.5
No probe temperature rise.
Try another predict cycle. If problem
persists, replace probe.
133
E0.9
Probe EEPROM is uninitialized. Bad probe
gain.
Calibrate probe or replace probe.
134
E0.9
Probe EEPROM is uninitialized. Bad probe
response value.
Calibrate probe or replace probe.
145
E0.2
A/D measurement overrun - pulse too
long.
Patient or environmental temperature
conditions may be too low. Verify
conditions at 80° F and 50° F
respectively. If conditions are valid and
problem persists, replace probe. If
problem persists, replace the SureTemp
Plus Thermometer module.
146
E0.2
A/D Measurement underrun - pulse too
short.
Patient or environmental temperature
conditions may be too high. Verify
conditions at 110° F and 104° F
respectively. If conditions are valid and
problem persists, replace probe. If
problem persists, replace the SureTemp
Plus Thermometer module.
147
E4.1
A/D measurement overrun - RCAL pulse
too long.
If problem persists, replace the SureTemp
Plus Thermometer module.
148
E4.1
A/D measurement underrun - RCAL pulse
too short.
If problem persists, replace the SureTemp
Plus Thermometer module.
149
E4.0
A/D measurement overrun - PTB pulse too If problem persists, replace the SureTemp
long.
Plus Thermometer module.
150
E4.0
A/D measurement underrun - PTB pulse
too short.
If problem persists, replace the SureTemp
Plus Thermometer module.
151
E0.2
A/D measurement overrun - timeout.
If problem persists, replace the SureTemp
Plus Thermometer module.
152
E0.9
Probe EEPROM is uninitialized.
Bad probe A/D calibration.
159
bv
Displayed when battery voltage is too low.
160
b^
Displayed when battery voltage is too
high.
161
E4.2
Reference power supply malfunction.
If problem persists, replace the SureTemp
Plus Thermometer module.
162
E4.8
Device not calibrated.
Calibrate device.
163
E4.9
Missing probe well - cycle will not start.
Insert probe well.
165
E4.3
Device EEPROM save failure.
Verify that the batteries are fresh. Try to
make changes again. If problem persists,
replace the SureTemp Plus Thermometer
module.
166
E0.8
EEPROM CRC Failure.
(CONFIG_TRANSFER_FAILURE)
Verify that the batteries are fresh. Try
again, if problem persists, replace the
component that is indicated.
106
Troubleshooting
Welch Allyn Spot Vital Signs LXi
Table 4. SureTemp Plus Temperature Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
167
E4.4
Device EEPROM read/save failure.
(CONFIG_START_FAILURE)
Verify that the batteries are fresh. Try to
make changes again. If problem persists,
replace the SureTemp Plus Thermometer
module.
168
E4.5
Device EEPROM read/save failure.
(CONFIG_SLAVE_ACK_FAILURE)
Verify that the batteries are fresh. Try to
make changes again. If problem persists,
replace the SureTemp Plus Thermometer
module.
169
E4.6
Device EEPROM read/save failure.
(CONFIG_MASTER_ACK_FAILURE)
Verify that the batteries are fresh. Try to
make changes again. If problem persists,
replace device.
170
E0.6
Probe EEPROM read failure.
(CONFIG_NULL_CHAR_FAILURE)
Verify that the batteries are fresh. Try to
make changes again. If problem persists,
replace the SureTemp Plus Thermometer
module.
171
71
Device EEPROM access failure.
(CONFIG_ACQUIRE_FAILURE)
Try another predict cycle. If problem
persists, replace probe.
172
72
Device EEPROM access failure.
(CONFIG_RELEASE_FAILURE)
Try another predict cycle. If problem
persists, replace probe.
173
73
Device EEPROM access failure.
(CONFIG_INVALID_PTR_FAILURE)
Try another predict cycle. If problem
persists, replace probe.
174
E4.7
Device EEPROM initialization failure.
(CONFIG_INITIALIZE_FAILURE)
If problem persists, replace the SureTemp
Plus Thermometer module.
175
E0.7
Probe EEPROM is un-initialized.
(CONFIG_UNINITIALIZED_PROBE)
Verify that the batteries are fresh. If
problem persists, replace probe.
180
E5.0
Heater stuck on. (ERROR_HEATER_ON)
If problem persists, replace the SureTemp
Plus Thermometer module.
181
E5.0
Heater stuck off. (ERROR_HEATER_OFF)
If problem persists, replace the SureTemp
Plus Thermometer module.
182
E5.0
Heater on when should be off.
(ERROR_HEATER_VOLTAGE_HIGH_Q)
If problem persists, replace the SureTemp
Plus Thermometer module.
183
E5.0
Heater on when should be off.
(ERROR_HEATER_VOLTAGE_Q_HIGH_
IMPEDANCE)
If problem persists, replace the SureTemp
Plus Thermometer module.
184
E5.0
Heater is off when it should be on.
(ERROR_HEATER_VOLTAGE_LOW)
If problem persists, replace the SureTemp
Plus Thermometer module.
185
E5.2
Heater hardware failsafe failure.
(ERROR_HEATER_FAILSAFE)
If problem persists, contact Technical
Support.
Table 5. SpO2 Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
1
3
--
Corrective Action
Missing or disconnected sensor.
Adjust or replace sensor.
No pulse from sensor.
Adjust or replace sensor.
Service Manual
Troubleshooting
Table 5. SpO2 Error Codes
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
4
E7
Retake reading; contact Technical
Support.
5
6
Communications failure.
8-second timeout interval
C8
Defective or bad SpO2 sensor.
Replace sensor.
C9
SpO2 time limit exceeded.
Remove sensor from patient.
107
108
Troubleshooting
Welch Allyn Spot Vital Signs LXi
Table 6. Comms Errors
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
1000
Err
Invalid Operation in this Context.
Internal error, contact Technical Support.
1001
Err
Auto zero in progress.
Internal error, contact Technical Support.
1002
Err
Bad checksum.
Internal error, contact Technical Support.
1003
Err
Unimplemented command.
Internal error, contact Technical Support.
1004
Err
Buffer Overflow.
Internal error, contact Technical Support.
1005
Err
Overrun error.
Internal error, contact Technical Support.
1006
Err
Wrong data count.
Internal error, contact Technical Support.
1007
Err
FPROM erase error.
Internal error, contact Technical Support.
1008
Err
FPROM programming error
Internal error, contact Technical Support.
1009
Err
Bad Motorola record.
Internal error, contact Technical Support.
1010
Err
A/D channel locked.
Internal error, contact Technical Support.
1011
Err
RTC not present.
Internal error, contact Technical Support.
1012
Err
Attempt to reference nonexisting cycle.
Internal error, contact Technical Support.
1013
Err
Data range error.
Internal error, contact Technical Support.
1014
Err
Alarm pair range error.
Internal error, contact Technical Support.
1015
Err
No POST error to clear.
Internal error, contact Technical Support.
1016
Err
Can’t clear this POST error.
Internal error, contact Technical Support.
1017
Err
Command not command type.
Internal error, contact Technical Support.
1018
Err
NAK from ST3800 protocol.
Internal error, contact Technical Support.
1019
Err
No wireless link.
Internal error, contact Technical Support.
Table 7. Comms Host Errors
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
2001
Err
Timeout.
Internal error, contact Technical Support.
2002
Err
Incorrect response header.
Internal error, contact Technical Support.
2003
Err
Incorrect response checksum.
Internal error, contact Technical Support.
2004
Err
Too much received data.
Internal error, contact Technical Support.
2005
Err
User cancelled.
Internal error, contact Technical Support.
2006
Err
User paused.
Internal error, contact Technical Support.
Service Manual
Troubleshooting
109
Table 8. Printer Errors
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
Corrective Action
5400
Err
Problem with the printer
Check all options; if problem persists,
contact Technical Support.
5401
Err
Printer is not responding.
5402
Err
Displayed when print started and printer is Printer head will not shut all the way or
out of paper.
too much paper.
5403
Err
Displayed when printing started and print
head is not closed in place.
Add paper.
Table 9. Spot Vital Signs LXi Errors
Internal
Event Log
Code
Number
Displayed
Internal Event Log Description
Device Code
5500
Corrective Action
Unknown error code.
5501
Err
Displayed when battery is too low for unit Charge battery; use wall transformer.
to continue operating.
5502
Err
Key stuck error causing the unit to be
automatically shut down.
110
Troubleshooting
Welch Allyn Spot Vital Signs LXi
Table 10. 802.11 b Radio Errors
LED
LED Color
Function
Power
Off
Bridge is not receiving power.
Red
Bridge failed its Power On Self Test (POST) and is not configured for
wireless communication.
Amber
Bridge passed its POST but is not configured for wireless
communication.
Green
Bridge passed its POST and is configured for wireless communication.
Off
Bridge is not receiving power.
Red
Bridge is searching for an Access Point.
Green
Wireless network and MAC have associated with an Access Point.
Off
No power or no wireless TCP session is established and no physical
serial connection is detected.
Red
No wireless TCP session is established; a physical connection is
detected.
Blinking Red
A physical serial connection was detected and there is serial traffic
present on that connection, but no wireless TCP session is established.
Amber
A wireless TCP connection is established but no physical serial
connection is detected (i.e. no serial cable is attached to the Bridge).
Blinking Green
A wireless TCP session is established, a physical serial connection is
detected, and the Bridge is transmitting or receiving data across the
wired serial port.
Green
A wireless TCP session is established, a physical serial connection is
detected, but there is n o active data movement across the wired serial
port.
Link
Comm
NOTE:The 802.11a/b/g radio has no functional LED displays.
Radio Test
Refer to Manufacturer’s Directions for Use.
Service Manual
Troubleshooting
Service Work Checklist
Spot Vital Signs
Model Number
Serial Number
Test
BP Cycle Count
Test Data
Technician
Date
Pass/Fail
Test Specification
Unit SW Version
N/A
N/A
SPO2 SW Version
N/A
N/A
Thermometry SW Version
N/A
N/A
Unit Pressure @ 0 mmHg
0 mmHg (+/- 1 mmHg)
Unit Pressure @ 50 mmHg
50 mmHg (+/- 1 mmHg)
Unit Pressure @ 150 mmHg
150 mmHg (+/- 1.5 mmHg)
Unit Pressure @ 250 mmHg
+/- 2.0 mmHg
Test Voltage @ 5.5 V
+0.1 VDC
Current Test – Sleep State
< 0.5 A
Current Test – Patient DAQ
< 1.25 A
Current Test – Valve Pump
< 2.0 A
Noise Level
< 0.05 mmHg
Button Test
Pass/Fail
Interface Test
Pass/Fail
Leak Test
<= 6mmHg in 15 seconds
Dump Test
< 10 Seconds
Inflation Test
< 7 Seconds
Valve Control Test
Pass/Fail
Over Pressure Test
296 to 329 mmHg
SPO2 Sensor - Masimo
81% +/- 3% 61bpm +/- 1bpm
SPO2 Sensor - Nellcor
90% +/- 1% 60bpm +/- 1bpm
Temperature Calibration Suretemp Plus
96.8 +/- 0.2°F 105.8 +/- 0.2°F
Temperature Calibration Braun Pro 4000
96.8 +/- 0.2°F 105.8 +/- 0.2°F
Temperature Cal Key Suretemp Plus
97.3 +/- 0.2°F
Radio Ping Test
Pass or Fail
Pass
111
112
Troubleshooting
Welch Allyn Spot Vital Signs LXi
Spot LXi Radio Configuration Tool
This CD configures the Spot Vital Signs LXi Radio to a local network. See the Welch Allyn
Spot LXi Radio Configuration Procedure (80012309) for further information.
113
9
Supplies and Accessories
Blood Pressure
Table 1. Reusable Blood Pressure Cuffs (1 per pack)
REF
Size
REF
Size
4500-01
Child
4500-03
Large Adult
4500-02
Adult
4500-04
Thigh
Table 2. Reusable Blood Pressure Cuffs (1 per pack)
REF
Size
REF
Size
REUSE-07-2MQ
Infant
REUSE-11-2MQ
Adult
REUSE-08-2MQ
Small Child
REUSE-12-2MQ
Large Adult
REUSE-09-2MQ
Child
REUSE-13-2MQ
Thigh
REUSE-10-2MQ
Small Adult
Table 3. Disposable Blood Pressure Cuffs (5 per box)
REF
Size
REF
Size
SOFT-07-2MQ
Infant
SOFT-11-2MQ
Adult
SOFT-08-2MQ
Small Child
SOFT-12-2MQ
Large Adult
SOFT-09-2MQ
Child
SOFT-13-2MQ
Thigh
SOFT-10-2MQ
Small Adult
Table 4. Miscellaneous Supplies and Accessories
REF
Description
REF
Description
4500-30
Blood Pressure Hose (5ft/1.5M)
4500-31
Blood Pressure Hose (10ft/3M)
4500-32
Blood Pressure Hose (8ft/2.4M)
114
Supplies and Accessories
Welch Allyn Spot Vital Signs LXi
Temperature
Table 5. SureTemp Plus
REF
Description
02895-000
SureTemp Plus Oral Probe and Well (9 feet/2.7M)
02895-100
SureTemp Plus Rectal Probe and Well (9 feet/2.7M)
02894-0000
SureTemp Plus Oral Well
02894-1000
SureTemp Plus Rectal Well
06138-000
SureTemp Plus Temperature Calibration Key
01802-110
9600 Plus Calibration Tester
05031-101
Disposable SureTemp Plus Probe Covers (1,000 covers, packaged 25/box)
20500-025M
Probe Cover-Box 25
400194
Assy, Suretemp Plus Components, Spot Vital Signs LXi
400195
PCA, Suretemp Plus OEM without EDAC Calibrated
400196
PCA, EDAC, Spot Vital signs LXi
Table 6. Braun ThermoScan PRO 4000
REF
Description
04000-200
Braun ThermoScan PRO 4000 Thermometer (for North America, South America, and
Asia Pacific)
04000-600
Braun ThermoScan PRO 4000 Thermometer (for Europe, Middle East, and Africa)
05075-800
Braun ThermoScan PRO 4000 Disposable Probe Covers (Case of 800 covers for North
America, South America, and Asia Pacific)
04000-800
Braun ThermoScan PRO 4000 Disposable Probe Covers (Case of 800 covers for Europe,
Middle East, and Africa)
01802-110
9600 Plus Calibration Tester
53020-0000
Braun ThermoScan PRO 4000 Rechargeable Battery Pack
4500-53
Braun Unlocking Key
4500-54
Repair-Braun with rechargeable batteries
Service Manual
Supplies and Accessories
Pulse Oximetry
Masimo Accessories
Table 7. Adhesive Sensors: Single-Patient Use
Catalog #
NEO-WRAP-RP
LNCS-INF-3
INF-WRAP-RP
Description
LNCS-ADTX
Replacement Wrap Infant Adhesive
YI-FM
Multisite Foam Wrap AD/PED/NEO, YI Sensor
LNCS-NEO-L-3
>30 kg
Disposable Adhesive Finger Sensor-Infant
Multisite Adhesive Wrap AD/PED/NEO, YI
Sensor
LNCS-TC-I
Quantity
Replacement Wrap Neo Adhesive
YI-AD
LNCS-YI
Weight Range
Multisite Reusable Sensor
Reusable Ear Sensor
Disposable Adhesive Finger Sensor- NEO/Adult
LNCS-ADTX
Adhesive Finger Sensor - Adult (20 per case)
LNCS-PDTX
Adhesive Finger Sensor - Pediatric (20 per case)
10 to 50 kg
LNCS-PDTX
LNCS INF-L
Adhesive Finger Sensor - Infant (20 per case)
3 to 20 kg
LNCS INF-L
LNOP-ADT
Adult sensor
>66 lbs (30 kg)
20
LNOP-PDT
Pediatric sensor
22 to 110 lbs
(10 to 50 kg)
20
LNOP-NEO
Neonatal sensor
<22 lbs (10 kg)
20
SofTouch neonatal preterm sensor
<2.2 lbs (1 kg)
20
Weight Range
Quantity
>66 lbs (30 kg)
1
LNOP-NEOPT
Table 8. Reusable Sensor
Catalog #
Description
LNCS-TC-I
Reusable Ear Sensor
LNCS-YI
Multisite Reusable Sensor
LNCS-DCI
Finger sensor - adult
LNCS-DCIP
Finger sensor - pediatric
10 to 50 kg
1
LNOP-DCI
Finger clip probe - adult
>66 lbs (30 kg)
1
LNOP-DCIP
Finger clip probe - pediatric
10 to 50 kg
1
Weight Range
Quantity
Table 9. Sensor Cables
Catalog #
Description
LNC-4-WA
4-foot cable with DB-9 connector for LNCS
NA
1
LNC-10-WA
10-foot cable with DB-9 connector for LNCS
NA
1
4-foot cable with sensor connector
NA
1
PC-04
115
116
Supplies and Accessories
Welch Allyn Spot Vital Signs LXi
Table 9. Sensor Cables
Catalog #
Description
Weight Range
Quantity
PC-08
8-foot cable with sensor connector
NA
1
PC-12
12-foot cable with sensor connector
NA
1
Service Manual
Supplies and Accessories
Nellcor Accessories
Table 10. OxiMax Adhesive Sensors: Single-Patient Use
Catalog #
Description
Weight Range
Quantity
MAX-AI
MAX-A Adhesive Sensor, adult
>66 lbs (30 kg)
Case of 24
MAX-PI
MAX-P Adhesive Sensor, pediatric
22 to 110 lbs
(10 to 50 kg)
Case of 24
MAX-II
MAX-I Adhesive Sensor, infant
6.5 to 44 lbs
(3 to 20 kg)
Case of 24
MAX-RI
MAX-R Adhesive Sensor, adult nasal
>110 lbs (50 kg)
Case of 24
Table 11. OxiMax OxiCliq® Sensors: Reusable Cable with Adhesive Sensor Bandage
Catalog #
OC-3
OXICLIQ-PI
Description
OxiCliq Sensor Cable (3 ft / 91cm)
OxiCliq P, pediatric
Weight Range
Quantity
N/A
1
22 to 110 lbs
(10 to 50 kg)
Case of 24
Table 12. OxiMax Reusable Sensors
Catalog #
Description
Weight Range
Quantity
DS-100A
Durasensor® DS-100A finger-clip sensor, adult
>88 lbs (40 kg)
1
< 6.5 lbs or > 88 lbs
(<3 kg or >40 kg)
1
® OXI-A/N, adult/neonatal
OXI-A/N
Oxiband
OXI-P/I
Oxiband OXI-P/I, pediatric/infant
6.5 lbs to 88 lbs
(3 to 40 kg)
1
D-YS
Dura-Y® D-YS, multisite sensor
>2.2 lbs (1 kg)
1
D-YSE
D-YSE ear clip for Dura-Y sensor
>66 lbs (30 kg)
1
6.5lbs to 88 lbs
(3 to 40 kg)
1
Weight Range
Quantity
N/A
1
D-YSPD
™ D-YSPD pediatric spot-check sensor
PediCheck
Table 13. OxiMax Sensor Cables
Catalog #
DOC-10
Description
DOC-10 (10 ft/3M)
117
118
Supplies and Accessories
Welch Allyn Spot Vital Signs LXi
Miscellaneous
REF
Description
4500-60
Mobile Stand, Spot Vital Signs LXi
4500-62
Wall Mount, Spot Vital Signs LXi
4500-84
Lead Acid Battery
705310
Directions for Use, Spot Vital Signs LXi English
705298
Quick Reference Card
4500-11
Child Inf. Bag, 2 Tube Monitor
4500-12
Adult Bag, 2 Tube Monitor
4500-13
Large Adult Inf. Bag, 2 Tube Monitor
4500-14
Thigh Inf. Bag, 2 Tube Monitor
4500-75
Kit, Desk Plate, Spot Vital Signs LXi
4500-89
Service Manual, Spot Vital Signs LXi
4500-150E
In-Service CD, Spot Vital Signs LXi
4500-100
Carrying Case, Spot Vital Signs LXi
4500-101A
AC Power Transformer (desktop transformer, line cord not included)
4500-200
Cuffkit, Child, Adult, Thigh, 2T Cuff & Bag
4500-202
Cuffkit, Small Child, Child, Small Adult 2T
4500-400
Line Cord (United States/Canadian/Japanese version)
4500-402
Line Cord (European version)
4500-404
Line Cord (United Kingdom version)
4500-406
Line Cord (Australian version)
4500-408
Line Cord (South African version)
4500-450
Transformer Mount, Spot Vital Signs LXi
4500-500
Kit, Printer, Spot Vital Signs LXi
4500-505
Printer Rechargeable Replacement Battery
4500-510
Printer Paper (10 rolls)
4500-520
Label Paper (10 rolls) and Cleaning Kit
4500-900
Kit, Dev Conn SDK Developers
4500-905
Repair Tool Software CD Kit
4500-906
Spot Vital Signs LXi Configuration CD
4500-907
Spot Vital Signs LXi Firmware Loader CD
4500-915
Image Team 4600 2D Bar Code Scanner Kit
4500-920
802.11b (DEPAC) Radio Kit
4500-921
Radio Directions for Use
4500-922
802.11 a/b/g Spot Vital Signs LXi Radio Kit
4500-923
Spot Vital Signs LXi a/b/g Radio Directions for Use
Service Manual
Supplies and Accessories
REF
Description
4500-925
USB 2.0 Cable for Wired Connectivity
4500-926
Cable for Wired Connectivity, Keyspan (USB to serial adapter)
4500-927
Spot Vital Signs LXi USB/serial Cable Kit
5200-08
Calibration T Fitting
119
Service Contracts
See the Welch Allyn Partners In Care™ web site (http://www.welchallyn.com/promotions/
services/default.htm) for a description of the different service contracts offered.
120
Supplies and Accessories
Welch Allyn Spot Vital Signs LXi
121
10
Field Replaceable Units
The following list identifies the available FRUs for Spot Vital Signs LXi. To order an FRU,
contact Welch Allyn Technical Support.
Table 1. Spot Vital Signs LXi Base Components
Component Number
Object Description
400163
ASSY, POWER HARNESS, Spot Vital Signs LXi
400170
ASSY, PUMP HARNESS
403912
PCA, MAIN, Spot Vital Signs LXi
400200
BASE UNIT, SURETEMP, NELLCOR - Spot Vital Signs LXi
400203
BASE UNIT COMPONENTS, Spot Vital Signs LXi
400207
LANGUAGE COMPONENTS, ENG, Spot Vital Signs LXi
400387
PBCA BP OEM, (MOD F)
4500-901
Spot Vital Signs LXi Pump and Pump Tubing Kit
4500-902
Spot Vital Signs LXi Pump Tubing Kit
4500-84
Lead Acid Battery
4500-101A
AC Power Transformer
400720
ASSY, BALLAST HARNESS, Spot Vital Signs LXi
400732
ASSY, BATTERY, Spot Vital Signs LXi
401082
Assy, Bezel and Window, Spot Vital Signs LXi
401250
Assy, Fan Unit Cooling
421051-12
TUBING,1/8 X 1/4 X 2.50
421051-9
TUBING,1/8 X 1/4 X 0.95
59P586
FOOT, RUBBER
620028-E
LABEL, CAUTION
620217
FITTING, “T”, 1/8 X 1/16X 1/8
700101
HSG, HANDLE, LXi
700102
HSG, HANDLE INSERT, LXi Ultra
700103
HSG, REAR, LXi
700105
HSG, BATT DOOR, Spot Vital Signs LXi
700110
BUMPER, LCD, Spot Vital Signs LXi
707237
SWITCH ARRAY, Spot Vital Signs LXi-New
700119
INVERTER, LCD
122
Field Replaceable Units
Welch Allyn Spot Vital Signs LXi
Table 1. Spot Vital Signs LXi Base Components
705653
HOUSING, FRONT, Spot Vital Signs LXi
704423
HSG, PANEL, SPO2-BLANK, Spot Vital Signs LXi
4500-89
SERVICE MANUAL, Spot Vital Signs LXi
401427
LABEL, ICON ID, Spot Vital Signs LXi
700863
CBL,FLX, 1/2mm,15POS,1.0”
704375
FLEX, MAIN, Spot Vital Signs LXi
701040
FITTING, PLASTIC L, 1/16 X 1/16
701502
Valve,Pneumatic,6PSI,5V,TH
703077
STANDOFF, PCB, BROACHING, #4 X .500 LG
703118
BATTERY CLIP, AA, SINGLE
703354
DISPLAY, LCD, 320X240, BLITE, MONO, 3.3V, 5.7"
703355
FILTER, AIR, 1/8 BARBS
705284
Spot Vital Signs LXi Warranty Card English
705298
QRC, Spot Vital Signs LXi English
705310
DFU, Spot Vital Signs LXi English
703842
TUBING, SILICONE, .063ID X .125OD X 5.50
700847
TUBING, SILICONE, .125IDx.25ODx1.75LG
421023-501
ASSEMBLY, SPOT PUMP REPAIR
4500-500
KIT, PRINTER, SPOT ULTRA (LXi)
4500-501
Spot LXi PRINTER UPGRADE KIT
713703
SPOT LXi PRINTER POWER SUPPLY
Table 2. SureTemp Plus Components
Component Number
Object Description
02692-100
PROBE ASSY,ORAL 9FT
02894-0000
ASSY,PRB WLL,BLUE,OEM,M690_692
400194
ASSY, SURETEMP+, COMPONENTS, Spot Vital Signs LXi
400195
PCA, SURETEMP+, OEM W/O EDAC, CALIBRATED
400196
PCA, EDAC, Spot Vital Signs LXi
700111
HOUSING, THERM OEM POD, Spot Vital Signs LXi
700112
PLATE, POD MOUNTING, Spot Vital Signs LXi
700858
CBL,FLX,1MM,6POS
700859
CBL,FLX,1MM,8POS
70999-0000
LABEL,SURETEMP TECHNOLOGY
02692-100
PROBE ASSY,ORAL 9FT
Service Manual
Field Replaceable Units
Table 3. Braun ThermoScan PRO 4000 Components
Component Number
Object Description
400652
PCA, BRAUN INTERFACE, Spot Vital Signs LXi
400831
BRAUN COMPONENTS, Spot Vital Signs LXi
700112
PLATE, POD MOUNTING, Spot Vital Signs LXi
700820
HSG, BOTTOM, BRAUN POD, Spot Vital Signs LXi
700822
HSG, BRAUN POD, Spot Vital Signs LXi
704365
WINDOW, BRAUN POD, Spot Vital Signs LXi
700859
CBL,FLX,1MM,8POS
703161
SECURITY LOCK, BRAUN POD, Spot Vital Signs LXi
703162
LATCH, BRAUN POD, Spot Vital Signs LXi
703164
CONTACT, BRAUN POGO, Spot Vital Signs LXi
703165
SPRING, COMPRESSION
703192
COVER, BRAUN SECURITY, Spot Vital Signs LXi
Table 4. Masimo SpO2 Components
Component Number
Object Description
008-0648-00
MASIMO LNOP-DCI ADULT REUSABLE SENSOR
008-0692-01
MASIMO - 8' INTERFACE CABLE
008-0960-00
MASIMO-LNCS-DCI ADULT REUSABLE SENSOR
008-1013-00
SP02 CABLE, LNCS, MASIMO, MINI-D, 4’, EXP
400192
PCA, MASIMO OEM, Spot Vital Signs LXi
400205
MASIMO SPO2 COMPONENTS, Spot Vital Signs LXi
400555
PCA, MASIMO ADAPTOR, Spot Vital Signs LXi
400610
ASSY, CABLE, FLAT FLEX, SPO2
704422
HSG, PANEL, SPO2-MASIMO, LXi
705651
HOUSING, FRONT MASIMO, Spot LXi
711350
MASIMO MS-11 SP02, STD, SW V4.6.0.2
LNC-10-WA
MASIMO, 10’ EXT CABLE, LNCS/DB-9
LNC-4-WA
MASIMO, 4’ EXT CABLE, LNC/DB-9
LNCS-ADTX
MASIMO, LNCS-ADTX ADULT ADHSV, 20 CASE
LNCS-DCI
MASIMO, LNCS-DCI ADULT REUSABLE SENSOR
LNCS-DCIP
MASIMO, LNCS-DCIP PED REUSABLE SENSOR
LNCS-INF-L
MASIMO, LNCS-INF-L INFANT ADHSV, 20 CASE
LNCS-PDTX
MASIMO, LNCS-PDTX PED ADHSV, 20 CASE
LNOP-ADT
DISPOSABLE ADHESIVE FINGER CLIP PROBE-AD
LNOP-DCI
REUSABLE FINGER CLIP PROBE-ADULT
LNOP-DCIP
REUSABLE FINGER CLIP PROBE-PEDIATRIC
LNOP-NEO
DISP ADHESIVE FINGER CLIP PROBE-NEONATE
123
124
Field Replaceable Units
Welch Allyn Spot Vital Signs LXi
Table 4. Masimo SpO2 Components
Component Number
Object Description
LNOP-NEOPT
DISPOSABLE FINGER SENSOR-NEONATE
LNOP-PDT
DISP ADHESIVE FINGER CLIP PROBE-PEDIATRIC
PC-04
4-FOOT CABLE W/ SENSOR CONN
PC-08
8-FOOT CABLE W/ SENSOR CONN
PC-12
12-FOOT CABLE W/ SENSOR CONN
Table 5. Nellcor SpO2 Components
Component Number
Object Description
400183
PCA, NELCOR OEM, Spot Vital Signs LXi
400201
NELLCOR SPO2 COMPONENTS, Spot Vital Signs LXi
400610
ASSY, CABLE, FLAT FLEX, SPO2
620377-1
“NELLCOR WORKS HERE” LABEL
704421
HSG, PANEL, SPO2-NELLCOR, LXi
704870
EVSPNELLCOR NELL3 PULSE OXIMETRY
DOC-10
CABLE, SPO2 EXTENSION, NELLCOR
DEC-4
EXTENSION CABLE 4 FT.
DS-100A
DURASENSOR,ADULT,DS-100A
D-YS
DURA-Y OXYGEN TRANSDER (1 sensor-40 wraps)
D-YSE
EAR CLIP (USE WITH DURA-Y SENSOR)
D-YSPD
PEDICHECK PEDIATRIC SPOT CHECK
MAX-AI
NELLCOR OXIMAX ADULT SENSOR (SU CS/24)
MAX-II
NELLCOR OXIMAX INFANT SENSOR (SU CS/24)
MAX-PI
NELLCOR OXIMAX PED SENSOR (SU CS/24)
MAX-RI
NELLCOR OXIMAX ADULT NASAL SEN (CS/24)
OC-3
NELLCOR OXICLIQ SENSOR CABLE
OXI-A/N
NELLCOR OXIBAND AD/NEO TRANSDUCER 1/50
OXICLIQ-PI
PEDIATRIC OXYGEN TRANSDUCER
OXI-P/I
NELLCOR OXIBAND PED/INF TRANSDUCER 1/50
Service Manual
Field Replaceable Units
Table 6. Radio Components
Component Number
Object Description
708920
Spot Vital Signs LXi Wireless Radio (A/B/G)
703380
Spot Vital Signs LXi Wireless Radio Mounting Bracket
704622
Spot Vital Signs LXi Wireless Radio Mounting Instructions
4500-915
Image Team 4600 2D Barcode Scanner Kit
703878
Null Modem 9-Pin M/F 4-40
4500-920
Kit, Spot Vital Signs LXi 802.11b Radio
4500-921
802.11 b radio Directions for Use
4500-922
Kit, Wireless Spot Vital Signs LXi 802.11a/b/g Radio
4500-923
802.11a/b/g Radio Directions for Use
4500-905
Repair Tool CD, Spot Vital Signs LXi
4500-906
Spot Vital Signs LXi Configuration CD
4500-907
Spot Vital Signs LXi Firmware Loader CD
4500-925
Cable for wired connectivity
4500-926
Cable for wired connectivity, Keyspan (USB to serial adapter)
4500-927
USB 2.0/serial cable kit
404684
Spot Vital Signs LXi Firmware Upgrade CD in case
404685
Spot Vital Signs LXi Radio Configuration CD in case
125
126
Field Replaceable Units
Welch Allyn Spot Vital Signs LXi
127
11
Disassembly and Repair
This chapter provides the instructions for removing and replacing serviceable modules in
the Spot Vital Signs LXi.
In general, re-assembly procedures are the reverse order of the disassembly procedures.
WARNING Electric shock hazard. There are no user-serviceable parts inside Spot
Vital Signs LXi other than battery replacement (see “Battery Replacement” on
page 46). Only an individual specifically trained and approved for the repair and/or
verification of this specific Welch Allyn product may perform maintenance
procedures specifically described in this manual. For service, refer the device to
an Authorized Service Center.
Note
Always disconnect the sealed lead-acid battery in the Spot Vital Signs LXi before
performing any repair function.
Tool list
Description
Part Number
Qty
Source
Blood Pressure Test Volume Repair Fixture
407672
1
Welch Allyn
Spot LXi Service Tool Software
4500-905
1
Welch Allyn
Service Manual, Spot Vital Signs LXi
704432
1
Welch Allyn
Spot Vital Signs LXi Directions for Use
705310
1
Welch Allyn
802.11b Radio
4500-920
1
Welch Allyn
802.11b Radio Directions for Use
4500-921
1
Welch Allyn
802.11a/b/g Radio
4500-922
1
Welch Allyn
802.11a/b/g Radio Directions for Use
4500-923
1
Welch Allyn
Tester, Calibration, 9600 Plus
01802-110
1
Welch Allyn
SureTemp Oral Probe
02895-000
1
Welch Allyn
Blood Pressure Y-Tube, No Fittings 1/8 Tube
5082-183
1
Welch Allyn
Welch Allyn Cuff
Soft-11-2MQ
1
Welch Allyn
Welch Allyn Blood Pressure Hose, 5ft.
4500-30
1
Welch Allyn
Cable, USB A to 5 pin mini
704889
1
Welch Allyn
DPAC Wireless Module
706514
1
Welch Allyn
Needle Nose Pliers
1
Tool/Supply Store
Wire Cutter
1
Tool/Supply Store
128
Disassembly and Repair
Description
Welch Allyn Spot Vital Signs LXi
Part Number
Qty
Source
Tweezers
1
Tool/Supply Store
#2 Phillips Screwdriver
1
Tool/Supply Store
T10 Torx Driver
1
Tool/Supply Store
4” PVC Pipe
1
Tool/Supply Store
Soldering Station
1
Tool/Supply Store
Cable Tie Tool - T9921
GS2B
1
Marsh Electronics
+1 800 877-8919
*Setra Pressure Meter
2270-01
1
Setra +1 800 257 3872
*Netech Pressure Meter
2000 in
1
Netech +1 800 547 6557
Nellcor Sensor Ext Cable (4’ Cable)
Dec-4
1
Nellcor +1 800 635 5267
Nellcor Sensor Ext Cable (8’ Cable)
Dec-8
1
Nellcor +1 800 635 5267
Nellcor Sensor
DS-100A
1
Nellcor +1 800 635 5267
Masimo SpO2 Tester
1795
1
Masimo +1 800 326-4890
Nellcor SRC-MAX SpO2 Tester
SRC-MAX
1
Nellcor +1 800 635 5267
Masimo Patient Cable
1005
1
Masimo +1 800 326-4890
Masimo Adult SpO2 Reusable Sensor
1269
1
Masimo +1 800 326-4890
Digital Volt Meter with 4 1/2 Digit Display
2
Electronics Supply Store
Power Supply: 0-20 Vdc adjustable with 0-3A
output
1
Electronics Supply Store
Wireless Router
1
Electronics Supply Store
Ethernet Cable
1
Electronics Supply Store
IBM compatible computer Windows 2000, XP,
NT4
1
* Only requires one of the pressure meters
To disassemble Spot Vital Signs LXi:
1. Disconnect the power and all accessories from the Spot Vital Signs LXi.
2. Remove the four screws holding the battery door using a phillips-head screwdriver.
Remove the battery door to expose the battery.
Service Manual
Disassembly and Repair
129
CTIONS
ort
MAT: 703956
Top, back housing
screws (2 places)
II
I
Battery Door
Screws (4 places)
3. Tip the Spot Vital Signs LXi backward and slide the battery out. Disconnect the oneway connector.
4. Remove the two screws inside the battery housing that are identified with arrows
molded into the housing and the two screws at the top of the back upper housing.
5. Hold the device together, lay the back housing on the bench, and carefully lift the top
housing off.
6. Remove the screw and slightly lift the circuit board from the right facing side and
disconnect the flex cable (J103).
130
Disassembly and Repair
Welch Allyn Spot Vital Signs LXi
7. Observe the locations of the two tubes before disconnecting. Lift and disconnect the
wire harnesses and the pneumatic tubing. The two wire harnesses are a 6-wire
harness that connects to J104 and a 2-wire harness that connects to J80 on the
small, mounted blood pressure board.
8. Disconnect the red electrical connector and the gold ribbon connector. This is located
on the main board. Lift up the tab on the white cable retainer so cable can slide out
after it is unplugged.
Gold Connector
Red Connector
9. Lift the flap on the beige connector (large ribbon cable) to remove the main board.
This releases the serial board cable from connector J108.
J108
Service Manual
Disassembly and Repair
131
Cut
jumper
JP2
JP2
Note
This step only applies to devices configured with Masimo SpO2 sensors. Cut
jumper JP2 with diagonal cutting pliers twice so that it is open. Cut it on each end
on the dotted lines as illustrated, so that it is an open connection.
132
Disassembly and Repair
Key Pad Disassembly
1. Gently pull the button switch array out of the cover.
2. Align and push the new button switch array into place.
Welch Allyn Spot Vital Signs LXi
Service Manual
Disassembly and Repair
133
SpO2 Circuit Board Disassembly
Note
To assure proper SpO2 operation, replace the SpO2 board using only the Welch
Allyn specified part.
To assure patient electrical isolation, after the main board is nearly back in
position, verity that the SpO2 flex cable is freely floating in space and is not
pressed up against the main board.
Masimo
Note
Masimo configurations ship with an EMI foil shield, copper tape, and Nomex
insulator. These components are removed from the illustrations to show clarity of
detail. These components must be reinstalled to comply with EMC requirements.
1. Lay the LCD flat on an ESD mat.
2. Find the double-stack of circuit boards and remove the four corners screws. Carefully
lift the circuit board straight up.
134
Disassembly and Repair
Welch Allyn Spot Vital Signs LXi
3. Remove the three screws on the circuit board located behind the LCD.
4. Slightly rock the circuit board back and forth while lifting straight up.
5. Replace with a new circuit board.
Nellcor
1. Lay the LCD flat on an ESD mat.
2. Remove the three screws on the circuit board located behind the LCD.
Service Manual
Disassembly and Repair
135
3. Slightly rock the circuit board back and forth while lifting straight up.
4. Replace with a new circuit board and set the dip switches to match the original board
(dip 1 and 2: up / dip 3 and 4: down).
136
Disassembly and Repair
Welch Allyn Spot Vital Signs LXi
Blood Pressure Circuit Board Disassembly
Note
When replacing the NIBP board see “NIBP board Initialization” on page 62 for
instructions.
Remove the four screws and carefully lift the circuit board straight up. There is one
stationary connector.
Service Manual
Disassembly and Repair
137
LCD Inverter Ballast Board Disassembly
This is a small board held in place with two-sided tape. It is located towards the bottom of
the main board. Remove the connector at each end and pull straight up while taking care
not to damage the board because the adhesive tape has considerable sticking strength.
LCD Disassembly
1. Remove the main board. At the bottom of this board is a circuit board with a pink
connector at the bottom.
2. Pull the brown tabs of the top connector forward and remove the ribbon cable.
Inspect connector tabs for wear and replace if worn.
3. Turn the board over and pull back the soft rubber holders. Pull the cable from the lug
to remove the grounding strap and remove the LCD.
4. Replace with a new LCD.
138
Disassembly and Repair
Welch Allyn Spot Vital Signs LXi
Pump Disassembly
Note
For proper blood pressure operation, replace the pump using only the Welch Allyn
specified part.
To assure patient electrical isolation, route the pump wires through the rear
housing clip feature (near the pump terminals) and held in place with a tiewrap to
the holes in the rear housing at the back of the battery compartment.
To assure patient electrical isolation, do not modify the length of the pump wires.
1. Snip the wire ties (2 places).
2. Disconnect the pneumatic tubing and unhook the wiring.
3. Replace with a new pump.
RS232-Communication Circuit Board Disassembly
1. Remove the pneumatic connector and associated hoses from the pump and the two
screws in the rear housing. Remove the associated hoses.
2. Release the catch and remove the cover and inner handle assembly.
3. Remove the connection port panel.
4. Remove the two screws inside the back housing and the ribbon cable that hold the
RS232 board in place. Take care since the connector is easily broken.
5. Slide the board straight out and remove the wire harness.
6. Replace with a new circuit board.
Service Manual
Disassembly and Repair
139
Fan and Power Circuit Board Disassembly
Note
To prevent buildup of hydrogen gas, replace the fan using only the Welch Allyn
specified part.
This is a small board held in place with two-sided tape and one connector. Remove the
screw before disconnecting the connector.
Thermometry Circuit Board Disassembly
Caution To assure patient electrical isolation, trap the flex cable to the
thermometer pod behind the clip on the main housing adjacent to the main board
connection point.
Caution To assure patient electrical isolation, verify that the correct flex cable is
used to connect the thermometer pod to the main board. The Braun and
SureTemp Plus flex cables are slightly different in length and are not
interchangeable.
Caution To protect the user from high voltage, properly install the thermometer
pod insulating paper separating the LCD ballast wires from the housing crack.
SureTemp Plus
Caution Do not attempt to repair or clean the solder joints on either SureTemp
Plus board. Incorrect flux or technique can degrade thermometer accuracy.
1. Remove the two screws located at the thermometer housing with a T-10 torx wrench.
Save the Nomex.
2. Locate the path of the notched tabs on the housing. Slide the housing up and out
following this path and set the case aside.
140
Disassembly and Repair
Welch Allyn Spot Vital Signs LXi
3. Remove the four screws from the mounting plate and save the Nomex. This exposes
the circuit board.
4. Remove the three Torx screws (T10) on the board (one on bottom and one on either
side of the probe well cover) and lift the board out of the housing and orient the part
as shown.
5. Disconnect all connectors and replace with a new board.
To replace the temperature connector, remove the one screw holding the temperature
board and connector. Verify the Nomex is properly mounted upon reassembly.
When replacing the SpO2/blood pressure housing, verify the orange and white twisted
wire is pushed as far into the handle housing as possible. Failure to do so can cause the
wires to stretch when the SpO2/blood pressure housing is inserted.
Service Manual
Disassembly and Repair
141
Braun ThermoScan PRO 4000
1. Remove the two screws located at the thermometer housing with a T-10 torx wrench.
Save the Nomex.
2. Locate the path of the notched tabs on the housing. Slide the housing up and out
following this path and set the case aside.
3. Remove the four screws that hold the metal shield in place.
4. Remove the springs and posts. Carefully rock the board back and forth while lifting
straight up.
5. Disconnect all connectors and replace with a new board.
6. Reassembly is the reverse of disassembly.
142
Disassembly and Repair
Welch Allyn Spot Vital Signs LXi
143
12
Repair Test Specifications
This appendix refers to the Spot Vital Signs LXi without pneumatics (tubing and cuff),
temperature probe, SpO2 probe, or main battery attached, unless otherwise noted.
Use the Repair Software for the performing the tests on the Spot Vital Signs LXi. The
standard test voltage, unless otherwise stated is 6.5 Vdc (+0/-0.25 Vdc). Unless
otherwise stated, all calibrated volumes are ±10cc of the stated volume.
General Unit Test
A-D Noise Test
The A-D Noise Test is defined as the amount of noise on the Spot Vital Signs LXi A-D
pressure channel; over a 1 second sample time while 0.0 mmHg is applied to the Device
pressure port. The maximum limit is 0.050 mmHg.
Leak Test
The Leak Test is defined as the amount of pressure drop that is recorded over a 15-second
interval with a 100cc cylinder attached to the Spot Vital Signs LXi pressure port and that
volume having a stabilized pressure of 250 mmHg. The maximum limit is 6 mmHg.
Inflation Test
The Inflation Test is defined as the amount of time the Spot Vital Signs LXi pump can
inflate a 250 cc cylinder from 5 mmHg to 210 mmHg. The maximum limit is 7 seconds.
Dump Test
The Dump Test is defined as the amount of time it takes Spot Vital Signs LXi to deflate a
500 cc cylinder from 260 mmHg to less than 15 mmHg. The maximum limit is 10
seconds.
Pneumatic Accuracy Test
Enter the Internal Configuration Mode to perform this test (see “Temperature Functional
Check” on page 77).
Perform an Auto-zero before starting this test (see “Temperature Functional Check” on
page 77). The Pneumatic Accuracy test is defined as the comparison of Spot Vital Signs
LXi’s pressure measurement and applied pressure at 0, 50, 150, and 250 mmHg. The
144
Repair Test Specifications
Welch Allyn Spot Vital Signs LXi
specification for each reading is within ±3 mmHg of the target pressure except for the 0
mmHg reading which is within ±1.0 mmHg.
Valve Control Test
Perform the valve control test using the Welch Allyn Spot LXi Service Tool, see “Valve
control test” on page 67.
Voltage Calibration
Calibrate the Spot Vital Signs LXi battery voltage measurement circuit at 5.5 + 0.1V DC.
After performing a successful battery measurement circuit calibration, Spot Vital Signs
LXi’s memory will store a calibration signature of up to four printable characters.
Blank Mode Current Test
The Blank Mode Current Test is defined as the amount of current drawn through the
battery terminals. All LCD segments, the back light, and the SpO2 mode are all turned off.
The limit is 200 mA maximum.
Back Light (Idle) Current Test
The Back Light Current Test is defined as the amount of current drawn through the
battery. All LCD segments and the back light are turned on while the SpO2 mode is turned
off. The limit is 400 mA maximum.
Valve/Pump Mode Current Test
The Valve/Pump Mode Current Test is defined as the amount of current that is drawn
through the battery terminals; Spot Vital Signs LXi is in the Blank Mode while the valve
and pump are actuated to on. The limit is 2.0 A maximum.
Interface Test
When given the proper commands, the Display Window will turn on or off all segments
and turn on or off the back light. When given the proper command, the buzzer sounds to
verify operation. The user determines the pass/fail criteria.
Temperature Option Requirements
Accuracy Test
Verify the accuracy of the temperature module is within ±0.2° F for readings with a
normal temperature of 97.3° F (36.3° C) using a Cal Key (5200-25). Verify Spot Vital Signs
LXi can read a temperatures of 96.4° F (35.8° C) and 106° F (41.1° C) within ±0.3° F/±0.2°
C using a Welch Allyn 9600 Plus Calibrator.
Service Manual
Repair Test Specifications
145
Temperature Probe Test
Spot Vital Signs LXi displays “ORL” after you remove the blue thermometer probe from
the blue probe well.
SpO2 Option Requirements
These tests are only valid on Spot Vital Signs LXi models with the Masimo or Nellcor
SpO2 option.
SpO2 Functional Test
See “To begin functional verification of the Masimo SpO2” or “To begin functional
verification of the Nellcor SpO2” on page 87 for the functional test.
SpO2 Mode Current Test
The SpO2 Mode Current Test is defined as the amount of current, less the Blank Mode
Current, that is drawn through the battery terminals, placing Spot Vital Signs LXi in the
Blank Mode, actuating the SpO2 mode and applying any SpO2 signal to the device. The
maximum limit is 120 mA maximum.
Fail Safe Test
Over Pressure Test
Verify that Spot Vital Signs LXi can detect over pressure on the pneumatic system
between 296 mmHg and 329 mmHg.
Over 15 mmHg
Verify that Spot Vital Signs LXi can detect static pressure over 15 mmHg for 180 seconds.
146
Repair Test Specifications
Welch Allyn Spot Vital Signs LXi
Service Manual
147
Interconnect Diagram 1
PNK
1
1
WHT
DGND
X3
DGND
J107
BACKLIGHT
J108
SERIAL
INTERFACE
DGND
SERA-PF-BAR
SERA-EN
SERA-RXE
LCD-VDD
LCD-LACD
LCD-LSCLK DGND
LCD-LP
LCD-FLM
SERA-RTS-BAR
BLU
2
+ 1
8
9
SERB-EN
GRN
SERB-RXE
BLK
VBUS
USB-SUSPND
SER-GND
ORN
+
4
+
5
WHT
6
D107
A1-F1
FUSE 5A
CHG-IN
1
CHG-GND
+3.15V
DGND
A1-J5
JTAG
2
4
6
8
10
12
14
16
18
20
Ferrite
+
2
S3
RESET
1
3
5
7
9
11
13
15
17
19
2
MNT10
USB-VPO
28
ANODE
CATH
INNER
INNER
DIGI-CAL
OUTER
LED(1)
OUTER
LED(8)
DIGI-GND
LED (1)
J103
THERMOMETER
2
MNT4
MNT6
P102
GND-ZBI
MNT5
1
2
RTS
7
TXD
3
CTS
8
DTR
4
ZC+5V
9
J1
SERIAL I
5
1
J10
GND-ZD
DTE
J6 P6
SPO2 SENSOR
Cut out for MS-11
LED (8)
GND-ZC
1
J101
SENSOR
DET+
GND-DIGI
DIGICAL
DETINNER
GND-ZB
A1-JP2
0
RXD
1
2
3
4
5
6
7
8
9
10
1
W6
SPO2 FPC ASSY
J8
SPO2
Mini-D
GND-ZBX
P101
A7
1
MNT24
1
RED-C
P1
MNT21
A8-J3
IR-C
+5VA
1
2
3
4
5
6
7
8
9
10
P3
MNT23
1
J90
SENSOR
ANODE
CATH
INNER
INNER
CONTROL
A10-P6
SENSOR
1
2
3
4
5
6
7
8
9
10
A10-J81
VALVE
B
MASIMO
ADAPTOR BOARD
W7
FFC
RST
DAV
RX
TX
NIBP BOARD
2
BLU
27
USB-VMO
1
A10
A10-J80
PUMP
1
DSR 6
26
1
B
J3
USB
DEVICE
DCD 1
24
1
1
2
3
4
5
6
7
8
9
10
MNT9
MNT7
DTE
18
25
C-LOCK
1
2
3
SPO2I-RESET-BAR
4
5 +12V
6 ANA-OUT
7
SPO2I-TX
8
SPO2I-RX
9 +5VA
10 CTS-BAR
11
12 +5VD
13
14
HOST_TX
VBUS
GND
HOST_DSR
HOST_RX
GND
PWR_ON
ECG_SYNC
DGND
1
2
3
4
5
6
7
8
MNT8
9
17
23
J102
SPO2 CONTROL
J105
NIBP CONTROL
FAN
2
16
29
RX
TX
HOST-WAKEUP-BAR
RESET-BAR
GND
POWER
W1-A1
15
DGND
POWER
INTERFACE
BOARD
ZC+5V
J2
SERIAL II
SERIAL
INTERFACE
BOARD
14
30
A6
W1-A1-J3
4
C
USB-RCV
FAN
6
5
4
3
2
1
2
8
DTR
GND-ZE
22
RED
BLK
3
CTS
21
DGND
+
7
TXD
20
USB-VM
+3.15V
NOPOP
center = +
1
2
RTS
19
USB-VP
J104
POWER
W1-A1-JP2
USB-OE-BAR
BAT-GND
3
RED
FFC
12
13
SERB-RTS-BAR
2
A5-F1
10
RXD
5
A2
W2
11
SERB-CTS-BAR
1
6
+5V
SERB-TX-BAR
BAT-IN
1
DSR 6
5
7
SERB-PF-BAR
2
+
1
DCD 1
3
+HST-IF
SER-SYNC
MAIN
BOARD
GND-IO
J11
VBUS
POWER
4
SERA-TX-BAR
A1
30
1
2
SERA-CTS-BAR
LCD-VEE
1
RED
1
Ferrite
5
4
3
2
1
1
X1
1
VBUS-IO
DGND
LCD-D0
LCD-D1
LCD-D2
LCD-D3
J110
USB-ID-BAR
BLK
C
J4
CHARGER
5
D
W1
POWER HARNESS
BATTERY
BATTERY
-
W4
RED
BLK
W5
J106
LCD
A5
CN1
1 1
2
INVERTER /
BALLAST
3
LCD
Pinout on LCD is
reversed from
standard Molex
assignment.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A4
CN2
A3
+5LCD
D
FRM
LOAD
CP
DISP-ON
VDD
VSS
VEE
D7/NC
D6/NC
D5/NC
D4/NC
D3
D2
D1
D0
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
W3
FFC
GRN
3
1
8
A13
J5
SURETEMP
PLUS
PROBE
THERMOMETER
INTERFACE
(EDAC) BOARD
MNT22
A8-J1
RED
BLK
A8
MASIMO SPO2
BOARD
Shield
A11
A11-F1
PUMP &
TUBING
A12
M
TRANSDUCER
TUBING
FILTER
A9-J1
CONTROL
6
1
A
A9
SURE TEMP
PLUS OEM
BOARD
A9-J3
PROBE
8
7
6
5
4
3
2
1
W8
FFC
PRODUCT ENCLOSURE
BLOOD
PRESSURE
CUFF
THIS INFORMATION IS THE
PROPERTYOF WELCH
ALLYN. IT IS SUBMITTED IN
CONFIDENCE AND IS NOT
TO BE DISCLOSED OR
UTILIZED WITHOUT
WRITTEN PERMISSION.
APPROVALS
CHECK
PROJ. MGR.
DATE
-
WELCH ALLYN
TITLE
Spot Lxi Interconnect Diagram
-
Source document:
40700-HDD
SIZE
NUMBER
REV
A
B
DATE 12/6/05
PCB Mat'l # (ref)
PCA Mat'l # (ref)
5
4
3
A
Note: This page depicts interconnect for basic unit plus Masimo
SPO2 and SureTemp Plus Thermometer options.
2
DRAWN BY
1
SHEET 1 of 2
K Burdick
148
Welch Allyn Spot Vital Signs LXi
Interconnect Diagram 2
5
4
3
2
1
X1
DGND
J110
X3
5
4
3
2
1
DGND
LCD-D0
LCD-D1
LCD-D2
LCD-D3
DGND
J107
BACKLIGHT
J108
SERIAL
INTERFACE
+5LCD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
2
D
1
D
DGND
SERA-PF-BAR
SERA-EN
SERA-RXE
SERA-TX-BAR
LCD-VDD
LCD-LACD
LCD-LSCLK DGND
LCD-LP
LCD-FLM
SERA-RTS-BAR
J106
LCD
7
8
9
SERB-PF-BAR
SERB-EN
SERB-RXE
USB-ID-BAR
VBUS
USB-SUSPND
C
BAT-GND
3
6
CHG-GND
+3.15V
DGND
J104
POWER
15
16
17
18
19
1
CHG-IN
A1-F1
FUSE 5A
14
C
D107
USB-VP
4
5
USB-OE-BAR
2
SER-GND
12
13
SERB-RTS-BAR
2
10
11
SERB-CTS-BAR
1
6
+5V
SERB-TX-BAR
BAT-IN
5
+HST-IF
SER-SYNC
MAIN
BOARD
3
4
LCD-VEE
A1
1
2
SERA-CTS-BAR
J5
JTAG
2
4
6
8
10
12
14
16
18
20
20
21
USB-VM
+3.15V
S3
RESET
1
3
5
7
9
11
13
15
17
19
2
22
23
USB-RCV
24
25
1
26
USB-VPO
27
USB-VMO
28
NOPOP
DGND
29
30
DGND
MNT9
MNT10
MNT4
1
J6
SPO2 SENSOR
ANODE
CATH
INNER
INNER
DIGI-CAL
OUTER
LED(1)
OUTER
LED(8)
DIGI-GND
LED (1)
Cut out for MS-11
MNT6
GND-ZBI
MNT5
1
2
3
4
5
6
7
8
9
10
W6
FPC
J8
SPO2
Mini-D
GND-ZBX
1
A14-J2
CONTROL
B
J101
SENSOR
LED (8)
J103
THERMOMETER
2
DET+
GND-DIGI
DIGICAL
DETINNER
GND-ZC
A1-JP2
0
1
1
2
3
4
5
6
7
8
9
10
RX
TX
HOST-WAKEUP-BAR
RESET-BAR
GND
POWER
6
5
4
3
2
1
HOST_TX
VBUS
GND
HOST_DSR
HOST_RX
GND
PWR_ON
ECG_SYNC
MNT7
1
2
3
4
5
6
7
8
MNT8
DGND
GND-ZB
C-LOCK
1
2
3
SPO2I-RESET-BAR
4
5 +12V
6 ANA-OUT
7
SPO2I-TX
8
SPO2I-RX
9 +5VA
10 CTS-BAR
11
12 +5VD
13
14
J102
SPO2 CONTROL
J105
NIBP CONTROL
A14-J1
SENSOR
B
A14
W9
FFC
NELLCOR
SPO2
BOARD
A15-J1
CONTROL
A15
6
A15-J2
WELL
CONTACTS
BRAUN
INTERFACE
BOARD
1
CHG/DATA
GND
2
1
Note: This page depicts interconnect for Nellcor SPO2 and Braun
Thermometer options only.
PRODUCT ENCLOSURE
A
A
THIS INFORMATION IS THE
PROPERTYOF WELCH
ALLYN. IT IS SUBMITTED IN
CONFIDENCE AND IS NOT
TO BE DISCLOSED OR
UTILIZED WITHOUT
WRITTEN PERMISSION.
APPROVALS
CHECK
PROJ. MGR.
DATE
-
WELCH ALLYN
TITLE
Spot Lxi Interconnect Diagram
-
Source document:
40700-HDD
SIZE
NUMBER
REV
A
B
5
4
3
2
PCB Mat'l # (ref)
DATE 12/6/05
PCA Mat'l # (ref)
DRAWN BY
1
SHEET 2 of 2
K Burdick
Reorder No. 4500-89
Material No. 718440 Ver. A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement