Pan Dacom 9.2 Speed-DSL Manual

Below you will find brief information for Speed-DSL SPEED-DSL 9.2. The SPEED-DSL 9.2 is a device that allows you to establish an Ethernet connection over 8 wires. It can achieve speeds up to 9.2 Mbit/s and supports loop bonding capability between all four ports. The device comes with a power supply and supports both single line and loop bonded G.SHDSL connections, as well as a 10/100 Ethernet port.

PDF Download

Document

Nets work together.
(9900-009-001-A, 9900-008-001-A)
Nets work together.
Notes
Before installing and putting the device into operation, please read the security guidelines at the
end of this documentation!
Pan Dacom would like to point out that the information and notes contained in these documents
are subject to technical changes. In particular, changes resulting from the continuing
development of the products may not have been taken into account. Pan Dacom does not
assume liability for print errors contained in this manual or other inaccuracies.
Pan Dacom explicitly points out that this manual only contains a general description of technical
processes and notes, and that their implementation as described is not necessarily sensible in
every individual case. In case of doubt, it is essential to confer with Pan Dacom.
This manual may not be copied, in whole or in part, or translated into other languages, without
the written consent by Pan Dacom.
&Oacute; by Pan Dacom Networking AG
Version 1.1
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 2 of 10
Nets work together.
1 INSTALLATION
1.1 Unpack and Inspect the Equipment
The following components should be included:
1 SPEED-DSL 9.2
1 power supply
1.2 Power Up the SPEED-DSL 9.2
Plug the power supply into the power adapter port on the back of the SPEED-DSL 9.2 and connect it to
your power source. Verify that the Power LED on the front of the SPEED-DSL 9.2 is illuminated.
NOTE Upon start up, the Ethernet link will remain disabled (as indicated by solid illumination of the
Ethernet 100, Act, and Lnk LEDs) until at least one of the four G.SHDSL connections has been
established.
1.3 Configure Bandwidth and Distance
Configuration switches for the G.SHDSL ports are on the back of the SPEED-DSL 9.2, numbered from
left to right, #1-8. Switches #1-3 on the SPEED-DSL 2.3-P work in tandem with one another to provide
eight bandwidth options for the four G.SHDSL ports as a group; bandwidth cannot be configured
individually for the G.SHDSL ports.
NOTE Configuration switches #1-3 are used for G.SHDSL bandwidth configuration on the SPEED-DSL
9.2-P ONLY. The SPEED-DSL 9.2etermines bandwidth via communication with its partner
G.SHDSL provider equipment. Switches #4-8 are not currently used on the SPEED-DSL 9.2
provider or subscriber models.
Position switches #1-3 on the SPEED-DSL 9.2-P according to the cable distance for your connection
and your desired G.SHDSL bandwidth. Distance capabilities listed in the following table assume the use
of 26 American Wire Gauge (AWG) cable. Connections made with cable of a lesser gauge (e.g., 24
AWG) will link up at greater distances. Your SPEED-DSL 9.2 may not link up if the cable is in poor
condition or if the cable distance is greater than a particular bandwidth will support; if link IS achieved
under such conditions, traffic quality may be affected (e.g., packets may be dropped).
Version 1.1
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 3 of 10
Nets work together.
Bandwidth and Distance Options
SWITCH #1 SWITCH #2 SWITCH #3 BANDWIDTH (KBPS) DISTANCE (FT) DISTANCE (M)
down
down
down
2,320
11,300
3,444
down
down
up
2,064
12,200
3,719
down
up
down
1,552
12,800
3,901
down
up
up
1,040
16,000
4,877
up
down
down
784
16,800
5,121
up
down
up
528
18,400
5,608
up
up
down
400
19,400
5,913
up
up
up
adaptive
varies
varies
NOTE The SPEED-DSL 9.2-P will run in Adaptive mode when switches #1-3 are in the Up
position: the four ports will train up to the best possible speed supported by the SPEEDDSL 9.2-P, the remote G.SHDSL equipment and the copper cable pair connecting the
two.
1.4 Connect the G.SHDSL Line(s)
The primary feature of the SPEED-DSL 9.2 is loop bonding capability between all four ports, though
both the provider and subscriber units can function with a single G.SHDSL connection as well.
1.4.1
Loop Bonded Connection
Using two, three or four G.SHDSL lines for one network connection (loop bonding) will net two, three
or four times the speed and data passing capability as a single G.SHDSL connection. Multiple
G.SHDSL lines used for one connection can also be considered as backup for each other should one
or more of the lines become disabled.
NOTE A SPEED-DSL 9.2 must be connected with equipment that is also loop bonding capable
in order to utilize the loop bonding feature; see the G.SHDSL Loop Bonding Product to
Product Feature Compatability list.
Plug your G.SHDSL cables into the G.SHDSL RJ45 ports (G.SHDSL 1, 2, 3 and/or 4) on the rear of
the SPEED-DSL 9.2; the order of connection is not important. Verify all connections: the G.SHDSL
Link (Lnk) LED for each connected port will pulse green to indicate the connection is established and
operational.
1.4.2
Single Line Connection
Plug your G.SHDSL cable into one of the four G.SHDSL RJ45 ports on the back of the SPEEDDSL 9.2; any of the four ports may be used. A single line connection can be established
between an SPEED-DSL 9.2-S and any of G.SHDSL provider equipment. Likewise, a single
line connection can also be established between an SPEED-DSL 9.2-P and G.SHDSL
subscriber units. Verify your connection: the G.SHDSL LED corresponding to the connected
port (G.SHDSL 1-4) will flash green to indicate the connection is established and operational.
Version 1.1
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 4 of 10
Nets work together.
G.SHDSL RJ45 Pinout
PIN CONNECTION
1
not used
2
not used
3
not used
4
ring
5
tip
6
not used
7
not used
8
not used
Link up time between local and remote G.SHDSL network extenders can vary from one to five minutes
depending on the quality, gauge and distance of the copper cable pair being used. If the cable distance
is greater than a particular bandwidth will support, the units may not link up or, if they do achieve link,
traffic quality may be affected (e.g., packets may be dropped).
1.5 Connect the Ethernet Line
NOTE If a G.SHDSL connection has not yet been made, the Ethernet link will remain disabled (as
indicated by solid illumination of the Ethernet 100, Act and Lnk LEDs) until at least one of the
four G.SHDSL links has been established.
1.5.1
Duplex Mode
The 10/100 Ethernet port auto-negotiates speed and duplex mode in accordance with the remote
equipment to which it's connected; Ethernet speed and duplex mode configurations cannot be hard
set on the SPEED-DSL 9.2. For the best connection results, the remote device (PC, hub, switch, etc.)
should be set to auto-negotiate speed and duplex mode as well. If the remote device cannot be
configured to auto-negotiate, speed may be hard set at either 10 Mbps or 100 Mbps but duplex mode
must be hard set to Half Duplex; a 10/100 Ethernet connection will not operate properly if the remote
device is hard set to Full Duplex.
1.5.1.1 Half Duplex
Receive and transmit functions are mutually exclusive; data transmission occurs in only one
direction at a time. Packet collisions are not unusual.
1.5.1.2 Full Duplex
Receive and transmit functions occur simultaneously, effectively doubling aggregate bandwidth
and preventing packet collisions.
Version 1.1
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 5 of 10
Nets work together.
10/100 Ethernet RJ45 Pinout
PIN CONNECTION
Version 1.1
1
Rx+
2
Rx-
3
Tx+
4
not used
5
not used
6
Tx-
7
not used
8
not used
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 6 of 10
Nets work together.
2 ADDITIONAL INFORMATION
2.1 LED Indications
LED
State
Indication
Additional Information
Power
solid green
unit is operational
If the Power LED is not illuminated, it is
unlikely that the SPEED-DSL 9.2 is
receiving power and therefore none of the
LEDs will be illuminated.
SDSL Link (Lnk)
Ports 1 - 4
pulsing
green
G.SHDSL
connection is
established and
active
Traffic is flowing.
solid green
problematic
G.SHDSL
connection
A connection exists but there is indication
of a problem with the G.SHDSL line.
no
illumination
no G.SHDSL
connection
See NOTE on following page.
flashing
amber
G.SHDSL activity
The SPEED-DSL 9.2 is receiving data.
solid amber
heavy Rx traffic
The SPEED-DSL 9.2 is receiving large
amounts of data.
no
illumination
no activity
A G.SHDSL link may exist but the SPEEDDSL 9.2 is not receiving any data.
G.SHDSL activity
The SPEED-DSL 9.2 is transmitting data.
heavy Tx traffic
The SPEED-DSL 9.2 is transmitting large
amounts of data.
no
illumination
no activity
A G.SHDSL link may exist but the SPEEDDSL 9.2 is not transmitting any data.
solid green
100 Mbps Ethernet If the Ethernet 100 LED is illuminated, the
connection is
Ethernet Lnk LED will also be illuminated.
established
See NOTE below.
no
illumination
no 100 Mbps
Ethernet
connection
pulsing
amber
standard operation Traffic is flowing without any problems
solid amber
heavy traffic
A solid amber Ethernet Act LED can also
signify a lost G.SHDSL connection; see
NOTE below.
no
illumination
no activity
Either there is no Ethernet link or a link
exists but there is no activity.
SDSL Data
Reception (Rx)
Ports 1 - 4
SDSL Data
flashing
Transmission (Tx) amber
Ports 1 - 4
solid amber
100 Mbps
Ethernet Link
(100)
10/100 Ethernet
Activity (Act)
Version 1.1
If the Ethernet 100 LED remains unlit but
the Ethernet Lnk LED is illuminated then a
connection has been established at 10
Mbps rather than 100 Mbps.
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 7 of 10
Nets work together.
10/100 Ethernet
Link (Lnk)
solid green
Ethernet
connection is
established
If the Ethernet Lnk LED is illuminated but not
the Ethernet 100 LED then a 10 Mbps
connection has been established. If the
Ethernet 100 and Lnk LEDs are BOTH
illuminated then a 100 Mbps connection has
been established.
A solid green Ethernet Lnk LED can also signify
a lost G.SHDSL connection; see NOTE below.
no
no Ethernet
illumination connection
The Ethernet 100 and Act LEDs will remain unlit
by default.
(A pulsing LED blinks steadily at a rate of once per second. A flashing LED blinks at a
more rapid, less constant rate.)
NOTE Upon start up, the Ethernet link will remain disabled (as indicated by solid illumination of
the Ethernet 100, Act, and Lnk LEDs) until at least one of the four G.SHDSL connections
has been established. Likewise, if one or more of the G.SHDSL connections had
previously been established but have since been lost, the Ethernet link will automatically
be disabled (as indicated by solid illumination of the Ethernet 100, Act and Lnk LEDs)
until at least one of the connections has been reestablished.
Version 1.1
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 8 of 10
Nets work together.
2.2 Regulatory Compliance for Class B Equipment
2.2.1
FCC Regulatory Compliance Information for Class B Equipment
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment uses,
generates and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
2.2.2
&middot;
Reorient or relocate the receiving antenna.
&middot;
Increase separation between the equipment and the receiver.
&middot;
Connect equipment to an outlet on a circuit different from the receiver.
&middot;
Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Regulatory Compliance Information for Class B Equipment
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil num&eacute;rique de la Classe B est conforme &agrave; la norme NMB-003 du Canada.
Version 1.1
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 9 of 10
Nets work together.
GS Nord
GS Ost
Merkurring 105
22143 Hamburg
Tel.: 040-679447-0
Fax: 040-67944750
Germania Bogen
Multimedia-Center
12099 Berlin
Tel.: 030-7508-3500
Fax: 030-7508-3535
GS West
Schiess Stra&szlig;e 55
40549 D&uuml;sseldorf
Tel.: 02131-17058-0
Fax: 02131-1705880
GS Mitte/Zentrale
Robert-Bosch-Stra&szlig;e 32
63303 Dreieich
Tel.: 06103-932-0
Fax: 06103-932400
GS S&uuml;dwest
GS S&uuml;d
Kurze Stra&szlig;e 40
70794 Filderstadt
Tel.: 0711-7705506-0
Fax: 0711-77055070
Inselkammerstra&szlig;e 10
82008 Unterhaching
Tel.: 089-614478-0
Fax: 089-61447850
Technical Hotline
06103 – 932 100
Fax: 06103 - 932 413
[email protected].
Version 1.1
SPEED-DSL 9.2 (9900-009-001-A, 9900-008-001-A)
page 10 of 10
">

Hello! I am an AI chatbot specifically trained to assist you with the Pan Dacom 9.2 Speed-DSL Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Ethernet connection over 8 wires
Up to 9.2 Mbit/s speed
Loop bonding capability
Single line G.SHDSL connections
10/100 Ethernet port
Power supply included

Frequently asked questions

The SPEED-DSL 9.2 can achieve speeds up to 9.2 Mbit/s.

Loop bonding capability allows you to use two, three or four G.SHDSL lines for one network connection, which can net two, three or four times the speed and data passing capability as a single G.SHDSL connection.

Yes, the SPEED-DSL 9.2 supports both single line and loop bonded G.SHDSL connections.

The 10/100 Ethernet port allows you to connect the SPEED-DSL 9.2 to a local network, such as a PC, hub, or switch.

The SPEED-DSL 9.2 comes with a power supply.