Epson | TC-1428 | Specifications | Epson TC-1428 Specifications

14" SVGA Color Monitor
TC-1428
Customer’s Record
The serial number of this product appears on the back of the unit.
You should note this serial number in the space provided below and retain
this manual as a permanent record of your purchase to aid in identification
in the event of theft or loss.
Model number: TC-1428
Serial number:
WARNING: To reduce the risk of fire or electric shock, do not expose this
Computer Display to rain or moisture.
CAUTION
The power cord is intended to serve as the main disconnect device. Install
the socket-outlet near the equipment and in an easily accessible place.
For 120V operation, use only with power cord plug having a parallel blade,
grounding type plug, rated 125V 10A.
For 240V operation, use only with power cord plug having a tandem blade,
grounding type plug, rated 250V 5A.
VESA DPMS Compliance Product Information
NOTE: The TC-1428 has been tested and found to comply with the
requirement of VESA DPMS standard. The power management
features are as follows:
1. The monitor will enter into the power saving state with six seconds of
time delay, in the absence of any sync. signal from PC.
- 1 -
2. The monitor will be automatically recovered to the on state by receiving
normal sync. signals from PC.
3. The power management states are identified below:
Power Mgmt. States
H-Sync. V-Sync.
LED Color
On
ON
ON
Green
Stand-By
OFF
ON
Light Amber
Suspend ON
OFF
Light Amber
Off
OFF
OFF
Dark Amber
OFF
OFF
Off
Power ON
Power OFF
Table of Contents
1 Introduction.. ............................................................................................ .3
2. Precautions ............................................................................................. .3
3. Features .................................................................................................. .4
4.Specifications ........................................................................................... 5
5.Control Locations and Adjustments ........................................................ .7
6.Connections ............................................................................................ .9
7. Pin Assignments.. ................................................................................... 10
8.Timing Charts.. ....................................................................................... 11
9.Troubleshooting.. ................................................................................... .13
Note: PC and VGA are trademarks of International Business Machines
Corporation.
-2-
1. Introduction
Congratulations on your purchase of a NEW ULTRA VGA monitor. One of
the most versatile monitors available today, the TC-1428 automatically
adjusts its vertical and horizontal scanning frequencies to those of your
computer’s graphics adapter or video chip sets. The TC-1428 provides
crisp text and vivid color graphic displays when used with NEW ULTRA
VGA compatible graphics adapters (see specifications).
2. Precautions
1. To prevent electric shock, do not remove screws or cover.
There are no user-serviceable parts inside the monitor. Refer servicing
to qualified service personnel.
DO NOT REMOVE THE TILT/SWIVEL BASE!
2. The input power source:
The TC-1428 is designed to be suitable for low input voltage (100125V) and high input voltage (200-240V) areas.
3. The monitor is equipped with a three-pronged grounding plug which will
only fit a grounded power outlet.
This is a safety feature. If you are unable to insert the plug into the
outlet, contact an electrician.
Do not remove
-3-
4. Do not put the monitor or other heavy objects on the power supply cord.
A damaged power cord may cause fire or electric shock.
5. Do not insert sharp objects into the monitor. They may cause fire or
failure.
6. Do not allow liquids to spill into the cabinet.
7. To reduce eye fatigue, avoid using the display in direct sunlight or under
bright lighting.
8. Do not operate the monitor beyond the specified temperature and
humidity range (see specifications on page 5).
9. For proper operation, keep the monitor adequately ventilated.
10. Keep the monitor away from strong magnetic fields produced by
transformers, motors, fans, or other devices.
11. If the monitor does not operate properly, turn the power switch off and
then unplug the monitor.
12. When irregular AC Voltages is supplied, a protective circuit will turn off
the monitor (the power indicator will also be turned off). If this happens,
turn off the power switch, and wait at least 30 seconds before turning it
on again.
3. Features
1. The TC-1428 monitor automatically adapts to the vertical and horizontal
frequencies of VGA, SVGA, 8514/A, VESA VGA, UVGA, and other
compatible graphics adapters.
2. The monitor features maximum resolutions of 1024 pixels (horizontal)
and 768 lines (vertical) in non-interlaced or interlaced modes.
3. Universal 100~240 Vac full-range power supply.
4. Power management complies with VESA DPMS standard, operating
states distinguished by the triple color power indicator.
5. Full scan capability allows the use of entire screen as display area.
6. The monitor compatible with the VESA DDC (Data Display Channel)
standard with DDC1 and DDC2b functionality (optional).
7. This monitor can be equiped with a built-in amplifier and stereo speakers
for multimedia environment applications (optional).
-4-
4. Specifications
Power Source:
AC 90~264V, 50/60Hz
Power Consumption:
75W Maximum
Power Management:
VESA DPMS (<5W)
Picture Tube:
14 inches, 90° deflection, 0.28mm dot pitch
Viewable size 13.1 inches.
Resolutions
Horizontal:
* Vertical:
l
Input Signals
* Video:
* Separate Sync:
1024 pixels (interlaced)
768 lines (interlaced)
Analog 0.7 Vp-p / 75 ohm Positive
TTL Level
Horizontal . . . . . . . . . . . Positive/Negative
Vertical . . . . . . . . . . . . . . . Positive/Negative
Synchronization
* Horizontal:
* Vertical:
31.5KHz/35KHz/38KHz
50Hz~100Hz continuous
Display Colors
* ANALOG Input:
Infinite colors (262, 144 color range)
Active Display Area
* Horizontal:
* Vertical:
250mm typical (varies by signal timing)
188mm typical (varies by signal timing)
Dimension
* (W)x(H)x(D):
370mm(14.6”)x355mm(14”)x394mm(15.5”)
VESA DDC Standard:
(Optional)
DDC1, DDC2b
Environmental Conditions
* Operating Temperature:
* Operating Humidity:
* Storage Temperature:
* Storage Humidity:
0°C~+35°C
10%-80% (non-condensing)
-40°C~+65°C
5%~95%
Interfaces (Optional)
* Audio Input:
* Audio Output:
Audio input port
Headphone jack
-5-
Low Radiation:
* X-ray radiation: < 100n Gylh
* Magnetic field:
Band I (5KHz-2KHz): < 250nT.
Band II (2KHz-400KHz): < 25nT.
Tilt and Swivel Operation:
The swivel range is normally limited to a range of 45 degrees to the right or
left of the front position (marked by a small molded pip on the top front
bottom of the base).
The tilt range is normally limited at an angle of -5 degrees forwards and +
15 degrees backwards. This allows you to set the screen angle to the
viewing position most comfortable to you.
Note: *When this display is operated with the vertical frequency under
55Hz, the image on the screen may flicker.
- 6 -
5. Control Locations and Adjustments
Note: The numbers indicate the control item whose description is found on
the following page.
-7-
Adjustments
1. POWER Switch
Push to turn the display on, and push again
to turn off.
The power indicator will light when the
display is on.
2. BRIGHTNESS Control
Adjusts the display to the desired brightness
level. (factory preset at the center detent of
the control knob)
3. CONTRAST Control
Adjusts the display to the desired contrast
level.
4. H. WIDTH Control
Adjusts the display to the desired horizontal
width. (factory preset at the center detent of
the control knob)
5. H. POSITION Control
Adjusts the display to the desired horizontal
position.
6. V. HEIGHT Control
Adjusts the display to the desired vertical
height. (factory preset at the center detent of
the control knob)
7. V. POSITION Control
Adjusts the display to the desired vertical
position.
-8-
6. Connections
Your monitor has two connecting cables: a Power Supply Cord, which
connects to a wall outlet, surge protector or other power source, and a
Signal Cable, which connects to the graphics adapter of your computer. To
insure safety and correct operation, always follow these four steps when
connecting the monitor:
1. Disconnect the power supply cords from your computer and monitor.
2. Connect the signal cable from the monitor to the graphics adapter of
your computer. The connector is shaped so that it will only fit when
properly aligned.
3. Secure the connection by tightening the two screws on the connector.
4. Plug the power supply cords of the computer and monitor into an AC
outlet.
Power Supply Cord
-9-
Signal Cable
7. Pin Assignments
The pin assignment of the video signal cable are shown below:
15-Pin Mini D-Sub Male Connector
PIN NO.
SIGNAL
1
RED
2
GREEN
3
BLUE
4
GROUND or OPEN FOR DDC
5
GROUND
6
R-GROUND
7
G-GROUND
8
B-GROUND
9
NO CONNECTION
10
GROUND or OPEN FOR DDC
11
GROUND
12
NO CONNECTION or DDC SDA
13
H. SYNC.
14
V. SYNC.
15
NO CONNECTION or DDC SCL
-10-
8. Timing Charts
SEPARATE SYNC.
HORIZONTAL
VERTICAL
Sync. Polarity: Positive/Negative
PRESET TIMING-VGA/SVGA
VGA
SVGA
640x350
720x400
640x480
800x600
800x600
Fh (KHz)
31.468
31.468
31.469
35.156
37.879
A µs (Line time total)
31.778
31.778
31.778
28.445
26.400
B µs (Synch. pulse)
3.813
3.813
3.813
2.000
3.200
C µs (Back porch)
1.907
1.907
1.907
3.556
2.200
25.423
25.423
25.422
22.222
20.000
0.636
0.636
0.636
0.667
1 .000
Fv (Hz)
70.000
70.000
59.940
56.250
60.317
P ms (Frame time total)
14.286
14.286
16.683
17.778
16.579
Q ms (Synch. pulse)
0.063
0.063
0.064
0.057
0.106
R ms (Back porch)
1.937
1.143
1.049
0.626
0.607
11.111
12.698
15.253
17.067
15.840
1.175
0.381
0.318
0.028
D µs (Active)
E µs (Front porch)
S ms (Active)
T ms (Front porch)
Separate
Separate
Separate
Separate
0.026
Separate
Sync.
Sync.
Sync.
Sync.
Sync.
H. Sync. Polarity
Positive
Negative
Negative
Negative
Positive
V. Sync. Polarity
Negative
Positive
Negative
Negative
Positive
No
No
No
No
No
-11-
PRESET TIMING-8514A/VESA VGA/UVGA
8514/A
UVGA
VESA VGA
1024x768
640x480
540x480
800x600
800x600
1024x768
Fh (KHz)
35.520
37.500
37.860
46.875
48.077
48.363
A µs (Line time total)
28.153
26.667
26.413
21.333
20.800
20.677
B µs (Synch. pluse)
3.919
2.032
1.270
1.616
2.400
2.092
C µs (Back porch)
1.247
3.810
4.064
3.232
1.280
2.462
D µs (Active)
22.810
20.317
20.317
16.162
16.000
15.754
E µs (Front porch)
0.178
0.508
0.762
0.323
1.120
0.369
Fv(Hz)
86.960
75.000
72.809
75.000
72.187
60.000
P ms (Frame time total:
11.500
13.333
13.735
13.333
13.853
16.667
Q ms (Synch. pulse)
0.113
0.080
0.079
0.064
0.125
0.124
R ms (Back porch)
0.563
0.427
0.740
0.448
0.478
0.601
S ms (Active)
10.810
12.800
12.678
12.800
12.480
15.880
T ms (Front porch)
0.014
0.026
0.238
0.021
0.770
0.062
Separate
Separate
Separate
Separate
Separate
Separate
Sync.
Sync.
Sync.
Sync.
Sync.
Sync.
H. Sync. Polarity
Positive
Negative
Negative
Positive
Positive
Negative
V. Sync. Polarity
Positive
Negative
Negative
Positive
Positive
Negative
Yes
No
No
No
No
No
Interlaced
-12-
9. Troubleshooting
Before you call an authorized service center, please check if the following
items are properly connected or not.
If a non-IBM personal computer or graphics adaptor is being used, make
sure the pin assignments of signal input connector and the signal timing
meet the specifications inducated above.
PROBLEM
CHECKS
LOCATION
Rear
Front
No Picture or
POWER Indicator off.
* AC Cord plugged in
* POWER Switch on
* Signal Cable connected
No Picture,
POWER Indicator off,
AC cord plugged in,
POWER switch on.
* Turn off POWER switch, wait
at least 30 seconds, turn it
back on.
Front
No picture,
POWER Indicator on.
* CONTRAST Control
* BRIGHTNESS Control
Front
Image is not centered.
* V. POSITION Control
* H. POSITION Control
Front
-13-
Rear
Front
Front
Federal Communications Commission Requirements
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, of not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
. . . ..Reorient or relocate the receiving antenna.
. . . ..lncrease the separation between the equipment and the receiver.
. . . ..Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
. . . ..Consult the dealer or an experienced radio/TV technician for help.
If necessary, consult your dealer’s service representative for additional
The user may find the booklet, “Something About
suggestions.
Interference”, prepared by the Federal Communications Commission,
helpful. This booklet is available from the U.S. Government Printing Office,
Washington DC 20402.
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment.
FCC Warning: To assure continued FCC emissions limit compliance, the
user must use only the provided shielded power supply cord and interfacing
cable when connecting to a host computer. Also, any unauthorized
changes or modifications to this equipment could void the user’s authority
to operate this monitor.
Canadian Department of Communications Requirements
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques
depassant les limites applicables aux appareils numberiques de classe B
prescrites dans le Reglement sur le brouillage radioelectrique edicate par le
Ministere des Communications du Canada.
- 14 -
P/N:5035111312
Download PDF

advertising