AMCON LENS LAYOUT BLOCKER EQ-3011 1-800-255-6161• Fax 1-800-397-0013

AMCON LENS LAYOUT BLOCKER EQ-3011 1-800-255-6161• Fax 1-800-397-0013
AMCON
LENS LAYOUT BLOCKER
EQ-3011
1-800-255-6161• Fax 1-800-397-0013
www.amconlabs.com
CONTENTS
DISCLAIMER AND GENERAL SAFETY WARNINGS................................................................2
NOMENCLATURE .....................................................................................................................3
PROCEDURES ..........................................................................................................................3
MAINTENANCE .........................................................................................................................4
Amcon Layout Blocker
__________________________________________________________________________________________
DISCLAIMER
Amcon: The Eyecare Supply Center makes no representations or warranties, either expressed
or implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, Amcon: The Eyecare Supply
Center reserves the right to revise this publication and to make changes from time to time in
the contents hereof without obligation of this company to notify any person of such revision or
changes.
NOTE: Neither manufacturer nor distributor assumes any responsibility or liability for any
damages caused by negligence or ignorance of precautions in this manual.
GENERAL SAFETY REQUIREMENTS
Please read the following warnings carefully to avoid injury as well as to not damage the
Pattern Maker.
WARNINGS
1. Do not use the instrument under flammable or explosive environments. Keep it clean
and dry. Avoid high temperatures.
2. Do not pull the power cord to disconnect power. Pull cord by the plug only.
3. In case of trouble with the instrument, first read the manual for troubleshooting to
problem. If this does not solve the problem, contact an authorized optical lab equipment
service repairperson.
2
Amcon Layout Blocker
__________________________________________________________________________________________
NOMENCLATURE
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Suction Cup Button
Suction Cup Head
Display Panel
Lens Pressing Arm
Frame Alignment Knob
Display Window
Lens Marking Button
Rubber Cap
Ink Box
Pointer Holder
Horizontal Alignment Knob
Power Switch
PROCEDURES
Turning on the Power
Turn the switch upward to turn the power on. Turn the switch downward to turn it off.
Lens Patterns
Place the lens pattern on the two plate needles in the center of the display panel.
3
Amcon Layout Blocker
__________________________________________________________________________________________
Lens Pressing Arm
Place the lens blank over the lens pattern. After the lens blank is in the correct position, place
the lens pressing arms on the lens blank to secure the lens into place.
Horizontal Alignment Knob
When this knob is turned, the three vertical lines will move towards the left or the right
simultaneously. This is used to decenter a lens horizontally.
Frame Alignment Knob
Turning this knob will move the two bottom of the two outer lines outward simultaneously.
Suction Cups
The use of suction cups is optional. Suction cups may be used in place of alloy and a metal
block. Place the suction cup onto the suction cup head. Then move the suction cup button
until the suction cup is aligned directly over the lens blank. Push down and the suction cup will
stick to the lens blank.
Suction Cup Head
Suction Cup
Head
Suction Cup
MAINTENANCE
Filling Ink Box
Slowly pour lens marking ink into the ink box through the small hole.
4
Amcon Layout Blocker
__________________________________________________________________________________________
Replacing the Bulb
Loosen the screw on the top cover and pull the cover up. Lift the light bulb cover and replace
the bulb. Put the top cover back into place and tighten the screw.
Replacing the Suction Cup Head
Loosen the suction cup holder screw and replace the head.
Suction Cup Head
Replacing the Print Button
Slowly press the print button. Do not loosen screw.
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement