- No category
advertisement
Ridgeline Installation and Upgrade Guide
Software Version 3.1 Service Pack 1
Extreme Networks, Inc.
3585 Monroe Street
Santa Clara, California 95051
(888) 257-3000
(408) 579-2800 http://www.extremenetworks.com
Published: February 2012
Part Number: 100397-00 Rev. 03
AccessAdapt, Alpine, Altitude, BlackDiamond, Direct Attach, EPICenter, ExtremeWorks Essentials, Ethernet
Everywhere, Extreme Enabled, Extreme Ethernet Everywhere, Extreme Networks, Extreme Standby Router
Protocol, Extreme Turbodrive, Extreme Velocity, ExtremeWare, ExtremeWorks, ExtremeXOS, Go Purple Extreme
Solution, ExtremeXOS ScreenPlay, ReachNXT, Ridgeline, Sentriant, ServiceWatch, Summit, SummitStack, Triumph,
Unified Access Architecture, Unified Access RF Manager, UniStack, XNV, the Extreme Networks logo, the Alpine logo, the BlackDiamond logo, the Extreme Turbodrive logo, the Summit logos, and the Powered by ExtremeXOS logo are trademarks or registered trademarks of Extreme Networks, Inc. or its subsidiaries in the United States and/or other countries.
sFlow is the property of InMon Corporation.
Specifications are subject to change without notice.
All other registered trademarks, trademarks, and service marks are property of their respective owners.
© 2012 Extreme Networks, Inc. All Rights Reserved.
2
Ridgeline Installation and Upgrade Guide
Contents
Ridgeline Installation and Upgrade Guide
3
Contents
Ridgeline Installation and Upgrade Guide
4
1
Installation Overview
C H A P T E R
This chapter provides an overview of the installation or upgrade of Ridgeline software, and includes the following sections:
●
●
●
●
●
●
“Installation Overview” on page 5
“The Ridgeline Server” on page 6
“The Ridgeline Client” on page 6
“System Requirements” on page 7
“Browser Requirements for Launching the Ridgeline Client” on page 10
“Obtaining a License Key for the Ridgeline Server” on page 11
NOTE
Ridgeline does not provide multi-language support.
Installation Overview
Ridgeline is a powerful, yet easy to use, client-server application for the centralized management of a network of Extreme Networks switches and selected third-party devices. Ridgeline offers a comprehensive set of network management tools that are easy to use from a client workstation with a web browser and the appropriate Java plug-in. The Ridgeline software can be installed on systems running Windows Vista, XP, Windows 2003 server, Windows 2008 server, or Windows 7 (Ridgeline 32bit version only) on SPARC workstations running Solaris 10, or on systems running Red Hat Enterprise
Linux version 5.
NOTE
This release, Ridgeline 3.1, will be the last release that supports Solaris.
There are several options for installing the Ridgeline 3.1 software, depending on whether you already have versions of Ridgeline installed, or whether this is a new Ridgeline installation.
Ridgeline Installation and Upgrade Guide
5
Chapter 1: Installation Overview
The Ridgeline Server
The Ridgeline server requires a license key, installed onto the server, to enable clients to connect to the server. You can perform the installation successfully without a Ridgeline license, but you will need to add a license key by running the License Manager, in order to use the Ridgeline product. License key installation is separate from the Ridgeline server installation.
You can run the License Manager at any time to add or upgrade licenses.
The installation process is very similar under Windows, Solaris, or Linux.
CAUTION
If you are running an evaluation version of the Ridgeline 3.1 software, and you want to retain the information in your Ridgeline database, DO NOT REINSTALL the Ridgeline software to upgrade to a permanent license.
● See
“Adding or Upgrading a License Key” on page 41
for instructions on running the License
Manager.
There are several additional (optional) components you may want to install along with your Ridgeline server: a difference viewer you can use to compare configuration files within the Configuration
Manager; and the SSH enabling key, which enables Ridgeline to use SSH2 instead of Telnet to communicate to the devices Ridgeline manages (assuming the devices are enabled to use SSH), and to securely upload and download configuration files.
●
●
See
“Installing a Difference Viewer” on page 47
for instructions on obtaining and installing a difference viewer.
See
“Enabling SSH for Secure Communications” on page 47 for information on enabling Ridgeline to
use SSH.
Upgrading the Ridgeline Server
From time to time Extreme Networks may choose to release updates to Ridgeline as a Service Pack release. On systems with a previously installed base release of the Ridgeline server, you can upgrade to a service pack release by installing a Ridgeline service pack patch. See
Service Pack Release” on page 11
for details.
NOTE
If you have been running a beta version of the Ridgeline 3.1 software, you must uninstall the beta version and do a new install of the final version. You cannot upgrade a beta version of the Ridgeline 3.1 software to the general availability (GA) release of the software.
The Ridgeline Client
The Ridgeline client is an application that is launched from a Microsoft Internet Explorer or Mozilla
Firefox browser. A browser is also required to display Ridgeline reports and to view the Ridgeline online help.
Ridgeline Installation and Upgrade Guide
6
System Requirements
The Ridgeline client can run on a different type of system from the server; for example, you can run the client on a Windows system connected to a Ridgeline server installed on a Linux system.
No software installation is required for a client to connect to the Ridgeline server; however, the
Java 1.6.0_25 and later plug-in is required, and you will be prompted to install it if it is not already present.
There is no separate installation package for the Ridgeline client. When you connect to the Ridgeline server with a browser and launch the Ridgeline client, all required files are downloaded and installed on your system automatically.
No license is needed to run the Ridgeline client; however, the Ridgeline server must have a valid license installed before any client connections are allowed.
NOTE
If you are running the Microsoft System Center Virtual Machine Manager (SCVMM), you must install the
Ridgeline XNV agent on the SCVMM host. For installation information, see Step 6 on page 55 .
System Requirements
The following sections specify the system requirements for installing and running Ridgeline 3.1.
Please check the most current version of the Ridgeline Release Notes for any additional or changed requirements for the Ridgeline release you are installing.
Windows Vista/XP/2003 Server/2008 Server/Windows 7
The Ridgeline Server. The system requirements for the Ridgeline server on Microsoft Windows are as follows:
● Microsoft Windows Vista, Windows XP Professional with SP1 or later, Windows 2003 server,
Windows 2008 server, or Windows 7 running on an Intel Pentium-compatible CPU.
NOTE
The Windows platform 32-bit version of Ridgeline 3.1 can be installed on any Windows platform listed above, regardless of whether it is a 32-bit or 64-bit machine/OS. The 64-bit version of Ridgeline 3.1 can only be installed on Intel-based 64-bit systems for the 64-bit Windows platforms listed above. If you try to install 64-bit
Ridgeline 3.1 on Itanium- or AMD-based 64-bit machines, the Windows OS might report an error message.
● 2 GB RAM minimum, 4 GB recommended.
Up to 4 GB might be needed to manage very large numbers of devices (1000 or more).
NOTE
If the Ridgeline Client and Server are to be run on the same machine, 4 GB RAM is recommended.
Ridgeline Installation and Upgrade Guide
7
Chapter 1: Installation Overview
●
●
●
2 GB disk space available, NTFS filesystem recommended.
2 GB of swap space minimum for the 32-bit version of Ridgeline; for the 64-bit version, we recommend a minimum of 4 GB of swap space.
1 GHz or greater Pentium-compatible processor (2 GHz or greater recommended).
The Ridgeline server software requires the installation of Oracle/Sun JRE 1.6.0_25 (or later). The
Oracle/Sun JRE 1.6.0_25 is included in the server installation and is the version we recommend you use.
NOTE
Additional disk space may be needed to hold alarm logs and other runtime data. The amount of space depends on the number of devices and the number of traps and syslog messages generated by the managed devices.
The Ridgeline Client. The system requirements for the Ridgeline client on Microsoft Windows are as follows:
●
●
●
Windows Vista, Windows XP Professional with SP1 or later, Windows 2003 server, Windows 2008 server, Windows 7 (Ridgeline 32-bit version only) running on an Intel Pentium-compatible CPU.
A monitor that supports at least 1024 x 768 resolution, and 16-bit color. Your system display settings must be set for at least 65536 colors.
512 MB RAM minimum (up to 1 GB recommended).
NOTE
If the Ridgeline Client and Server are to be run on the same machine, 4 GB RAM is recommended.
●
●
●
256 MB of disk space, NTFS filesystem recommended.
Swap space equal to double the amount of memory. For example, if you have 512 MB of RAM, you should have 1 GB of swap space.
A browser (Mozilla Firefox or Microsoft Internet Explorer) is required to launch the Ridgeline client, display reports, and view the Ridgeline online help.
Sun Microsystems Solaris 10
NOTE
This release, Ridgeline 3.1 will be the last release that supports Solaris.
The Ridgeline Server. The Ridgeline server software, version 3.1, is supported on the Sun Solaris operating environment on SPARC workstations. The system requirements for the server and client are as follows:
●
●
2 GB RAM minimum, 4 GB recommended.
Up to 4 GB may be needed for very large numbers of devices (1000 or more).
400 Mhz or better processor
Ridgeline Installation and Upgrade Guide
8
System Requirements
●
●
2 GB disk space available.
Swap space equal to double the amount of memory. For example, if you have 512 MB of RAM, you should have 1 GB of swap space.
The Ridgeline server software requires the installation of Oracle/Sun JRE 1.6.0_22 (or later). The
Oracle/Sun JRE 1.6.0_22 is included in the server installation and is the version we recommend you use.
NOTE
Additional disk space may be needed to hold alarm logs and other runtime data. The amount of space depends on the number of devices and the number of traps and syslog messages generated by the managed devices.
The Ridgeline Client. The system requirements for the Ridgeline client on Solaris are as follows:
●
●
●
●
●
A monitor that supports at least 1024 x 768 resolution, and 16-bit color. Your system display settings must be set for at least 65536 colors.
512 MB RAM minimum. (Up to 1 GB recommended.)
256 MB disk space available.
Swap space equal to double the amount of memory. For example, if you have 512 MB of RAM, you should have 1 GB of swap space.
A browser (Mozilla Firefox) is required to launch the Ridgeline client, display reports, and view the
Ridgeline online help.
Red Hat Enterprise Linux 5
The Ridgeline Server. The Ridgeline server software, version 3.1, is supported on Red Hat Enterprise
Linux version 5. The system requirements are as follows:
NOTE
The Linux platform 32-bit version of Ridgeline 3.1 can be installed on the Linux platform listed above, regardless of whether it is a 32-bit or 64-bit machine/OS. The 64-bit version of Ridgeline 3.1 can only be installed on Intel-based 64-bit systems for the 64-bit Linux platform listed above. If you try to install 64-bit
Ridgeline 3.1 on Itanium- or AMD-based 64-bit machines, the Linux OS might report an error message.
●
●
●
●
●
2 GB RAM minimum, 4 GB recommended.
Up to 4 GB may be needed for very large numbers of devices (1000 or more).
1 GHz or greater Pentium-compatible processor (2 GHz recommended).
2 GB disk space available.
Swap space equal to double the amount of memory. For example, if you have 512 MB of RAM, you should have 1 GB of swap space.
A GUI/Desktop environment must be installed on the server machine.
The Ridgeline server software requires the installation of Oracle/Sun JRE 1.6.0_22 (or later). The
Oracle/Sun JRE 1.6.0_22 is included in the server installation and is the version we recommend you use.
Ridgeline Installation and Upgrade Guide
9
Chapter 1: Installation Overview
NOTE
Additional disk space may be needed to hold alarm logs and other runtime data. The amount of space depends on the number of devices and the number of traps and syslog messages generated by the managed devices.
The Ridgeline Client. The system requirements for the Ridgeline client on Red Hat Enterprise Linux are as follows:
●
●
●
●
●
A monitor that supports at least 1024 x 768 resolution, and 16-bit color. Your system display settings must be set for at least 65536 colors.
512 MB RAM minimum (1 GB recommended).
256 MB disk space available.
Swap space equal to double the amount of memory. For example, if you have 512 MB of RAM, you should have 1 GB of swap space.
A browser (Mozilla Firefox 1.5 or higher) is required to display reports and view the Ridgeline online help.
Browser Requirements for Launching the Ridgeline Client
The Ridgeline client is launched from a browser window. Ridgeline uses signed applets. You will be prompted to accept the security certificate from Extreme Networks the first time you try to launch the applet.
NOTE
The Java plug-in version 1.6.0_25 and later is required for the Ridgeline client. If this version of the plug-in is not already installed, you will be prompted to download it the first time you try to launch the Ridgeline client.
Table 1 lists the browsers that are supported by the Ridgeline 3.1 release. A browser is also required to display Ridgeline reports and the Ridgeline online help.
Table 1: Ridgeline 3.1 supported browsers
Operating System
Windows
Sun Solaris 10
Red Hat Enterprise Linux version 5
Minimum Browser Configuration
Internet Explorer™ 6.0 or higher, Mozilla Firefox 1.5 or
2.0
Mozilla Firefox 1.5, 2.0, or 3.0
Mozilla Firefox 3.0
NOTE
For the Mozilla Firefox browser, you must install the Java plug-in, and then link it to the Firefox browser.
See
“Configuring the Firefox Browser for the Java Plug-In” on page 57
Ridgeline Installation and Upgrade Guide
10
Upgrading Ridgeline to a Service Pack Release
Upgrading Ridgeline to a Service Pack Release
From time to time Extreme Networks may elect to release updates to the current Ridgeline release as
Service Packs. Service Packs are minor releases that provide fixes for known problems from previous releases.
A Service Pack is released as a patch release that integrates the Service Pack fixes into an existing base
Ridgeline software installation. If you already have the Ridgeline software installed on your system when a Service Pack is released, you can add the Service Pack fixes by installing the patch release. See
“Installing a Service Pack Release” on page 60 for installation instructions.
If the Service Pack you want to install is for a different base release than the one currently installed on your system, first install the base release and then install Service Pack patch.
After you upgrade the Ridgeline 3.1 server to a Service Pack release, if any files are necessary to run the
Ridgeline client on your system, they are downloaded and installed automatically when you launch the client.
Obtaining a License Key for the Ridgeline Server
To log in to the Ridgeline server from a Ridgeline client, Ridgeline must be configured with a valid license. You can install the software without a license key, but you cannot connect to it from a Ridgeline client. (If you install the product without a license key, you can add the key later using the License
Manager, described in “Installing a Permanent License When an Evaluation License is Already
).
Ridgeline licenses allow you to use all of the standard features of the product, including discovery and visualization of the devices in your network, scripting, and point-and-click provisioning for VLANs and
EAPS domains. Additional feature licenses are available from Extreme Networks that unlock additional
Ridgeline features, including: identity management, VM support, and service provider features, such as
E-LINE, E-LAN, VMAN (PB), PBB and VPLS discovery, monitoring, and provisioning for an unlimited number of devices. For more information about the various types of software licenses available for
Ridgeline, refer to the Ridgeline Release Notes.
Ridgeline Installation and Upgrade Guide
11
Chapter 1: Installation Overview
You can get two types of licenses from Extreme Networks, an evaluation license and a permanent license at www.extremenetworks.com/go/ridgelinelicense . Select the option for the license key you want.
Evaluation License
An evaluation license allows you to run the product on a temporary basis. If you want to continue using the product beyond the evaluation period, you must obtain a permanent license.
To get an evaluation license:
1 Go to: www.extremenetworks.com/go/ridgelinelicense
2 Select the option to obtain an evaluation license key.
3 Enter your name, company information, and similar information, and an email address to which your license key should be sent.
Your evaluation license key will be sent to you by return email.
If your evaluation license expires before you have finished evaluating the product, you can request another evaluation key, up to three evaluation keys for a total of 90 days of evaluation use.
Permanent License
A permanent license has no time limit. Permanent licenses are sold based on the number of devices you want Ridgeline to manage.
To obtain a permanent license:
1 You must provide your activation key, found on the license agreement shipped with your purchased product.
2 Fill in the requested information, and enter your activation key. The activation key is a 14-character key that starts with “AC” found on the License Agreement you received when you purchased the product.
Your permanent license key will be sent to you by return email.
Ridgeline Installation and Upgrade Guide
12
Installing a Permanent License When an Evaluation License is Already Installed
Distinguishing Between a License Key and an Activation Key
Both permanent and evaluation license keys are 14-character keys that start with “RS” and are followed by 12 additional upper- and lower-case alphabetic characters, numbers, and special characters such as
“+”.
The license key is NOT the same as the activation key, which starts with “AC,” and is found on the
License Agreement shipped with your purchased product. You use the activation key to obtain a permanent license.
Installing a Permanent License When an Evaluation
License is Already Installed
To install a Ridgeline evaluation or permanent license, or to upgrade an evaluation license to a permanent license you must run the License Manager. Until you install a license, no client will be able
to connect to the Ridgeline server. Refer to “Adding or Upgrading a License Key” on page 41 for
instructions to do this.
Ridgeline Installation and Upgrade Guide
13
Chapter 1: Installation Overview
14
Ridgeline Installation and Upgrade Guide
2
Downloading Ridgeline
Software
C H A P T E R
This chapter comprises information and procedures to download images from Extreme Networks eSupport. In some specific cases, the process might be different and is noted when applicable.
It contains the following sections:
●
●
●
“Determining Device Serial Numbers” on page 16
“Providing Serial Numbers to Extreme Networks eSupport” on page 18
Overview
Using the Ridgeline Firmware Manager, you can download software and BootROM images from
Extreme Networks to your Ridgeline server, then upgrade the devices in your network with the new images. To download new images from Extreme, you must have a current support contract and an
Extreme Networks eSupport user name and password.
You also need to provide eSupport with the serial number of a device of the type you are upgrading in order to obtain updated images for that type of device. For example, to obtain updated Summit X650 software, you need to provide the serial number of one of the Summit X650 switches in your network prior to downloading the software. After you do this, the updated Summit X650 software can be downloaded from Extreme, and you can use it to upgrade any of the Summit X650 switches in your network. For chassis devices, you provide the serial number of a Management Module or I/O Module.
Once you have provided the serial number for the device, you can download subsequent image updates for that type of device without having to enter the serial number again.
If you have not yet provided eSupport with a serial number for the device type you are upgrading, you may see the following window when you attempt to download a new image using Firmware Manager:
Ridgeline Installation and Upgrade Guide
15
Chapter 2: Downloading Ridgeline Software
Figure 1: Progress and Results Window Showing Unsuccessful Image Download
To obtain the new images, you must determine the serial numbers for the type of device you want to upgrade, then supply those serial numbers to Extreme Networks eSupport. Refer to
Device Serial Numbers” on page 16
. After you do this, the software images download normally.
Determining Device Serial Numbers
The serial number for a device is displayed in the Device Properties window. To display this window, select a device, then select Properties from the File menu, or from the right-click pop-up menu. The device serial number appears in the System ID field, as shown in Figure 2.
Figure 2: Location of Serial Number in the Device Properties Window
Device Serial Number
Chassis Part Number
Ridgeline Installation and Upgrade Guide
16
Determining Device Serial Numbers
You can also display the serial numbers of devices in your network by running a Device Details report in Ridgeline. For example:
Figure 3: Device Details Report
Ridgeline Installation and Upgrade Guide
17
Chapter 2: Downloading Ridgeline Software
To display the serial numbers of individual modules (Figure 4), run the Card Summary report.
Figure 4: All Cards Card Summary Report
Providing Serial Numbers to Extreme Networks eSupport
To provide serial numbers to Extreme Networks eSupport, complete the following steps:
1 Go to www.extremenetworks.com and log into the eSupport page with your eSupport user ID and password.
Figure 5: eSupport Login page
2 Select the Download Software Updates link.
18
Ridgeline Installation and Upgrade Guide
Providing Serial Numbers to Extreme Networks eSupport
Figure 6: Download Software Updates Link on eSupport Page
3 In the Serial # box, enter the serial number of the device or module, and click Software Downloads.
NOTE
For chassis devices, you must provide the serial number of a Management Module or I/O Module.
Figure 7: Serial Number Entry Box
NOTE
If you are upgrading SSH on a switch, you must do this operation for each Ridgeline switch.
4 Accept the terms of the software license agreement and click Submit.
Figure 8: Software License Agreement
Ridgeline Installation and Upgrade Guide
19
Chapter 2: Downloading Ridgeline Software
A table of the software versions available for the device is displayed. If the device is under a service contract, all software versions are displayed; otherwise, only software versions available for the 90-day warranty period are displayed. For example:
Figure 9: List of Available Software Versions for a Device
5 In the Ridgeline Firmware Manager, select one of the software versions listed in the eSupport table.
When you do this, the software image is downloaded to the Ridgeline server.
Figure 10: Downloading a Selected Software Image to the Ridgeline Server
20
Ridgeline Installation and Upgrade Guide
3
Installing the Ridgeline 3.1
Server
C H A P T E R
This chapter describes how to install or upgrade the Ridgeline 3.1 server software in Windows, Solaris, and Linux, and includes the following sections:
CAUTION
If you are running an evaluation version of the Ridgeline 3.1 software, and you want to retain the information in your Ridgeline database, DO NOT REINSTALL the Ridgeline software to upgrade to a permanent license.
●
●
●
●
●
●
●
●
●
“Installation Overview” on page 21
“Installing the Ridgeline Server” on page 23
“Adding or Upgrading a License Key” on page 41
“Starting and Stopping the Ridgeline Server” on page 42
“Configuring the Ridgeline Server for NATed Client Connections” on page 44
“Installing Ridgeline on a Multi-Homed Server” on page 45
“Installing a Difference Viewer” on page 47
“Enabling SSH for Secure Communications” on page 47
“Uninstalling the Ridgeline Server Software” on page 48
Installation Overview
You can install the Ridgeline server in the following environments:
● Microsoft Windows Vista, Windows XP Professional with SP1 or later, Windows 2003 server,
Windows 2008 server, or Windows 7 (Ridgeline 32-bit version only) running on an Intel Pentiumcompatible CPU
●
● or
Red Hat Enterprise Linux Version 5 or
Solaris 10 running on a SPARC system
Ridgeline Installation and Upgrade Guide
21
Chapter 3: Installing the Ridgeline 3.1 Server
NOTE
This release, Ridgeline 3.1 will be the last release that supports Solaris
The installation process is very similar under all three operating environments; the few differences are noted in the description of the process when applicable.
See
“System Requirements” on page 7
for memory, CPU, disk and other requirements.
To install the Ridgeline server you will need the following information:
● The HTTP port for communication with Ridgeline clients (default is 8080)
● A license key. See
“Obtaining a License Key for the Ridgeline Server” on page 11 for more
information.
NOTE
Prior to installing Ridgeline, make sure the system where you are installing the software is DNS-resolvable and accessible both by IP address and by hostname from all machines where the Ridgeline client will be launched.
If it is not, add an entry for the system in the local DNS server or the hosts file on the client machines.
Retaining the Database when Reinstalling Ridgeline
CAUTION
If you are running an evaluation version of the Ridgeline 3.1 software, and you want to retain the information in your Ridgeline database, DO NOT REINSTALL the Ridgeline software to upgrade to a permanent license.
Reinstalling Ridgeline will reinitialize the database, which erases all information in the database. To update an evaluation copy of the Ridgeline server to a licensed copy without reinitializing the database,
follow the update procedure described in “Adding or Upgrading a License Key” on page 41 .
User Permissions
To install the Ridgeline software components as services under Microsoft Windows as daemons under
Solaris/Linux, you must have administrator privileges on that system.
Local Name Resolution for the Server
The system on which Ridgeline is installed must be able to resolve both its own local name and its domain name. For example if you install Ridgeline on a system named system1 , then it must be able to resolve both system1 and its domain name, such as system1.company.com.
You can test for this by attempting to ping the system using both the local name and the domain name. If there are problems resolving either of these names, make sure the hosts file contains the correct information.
Ridgeline Installation and Upgrade Guide
22
Installing the Ridgeline Server
Required Patches for Solaris
The Solaris operating environment may require patches for the Ridgeline software to function properly.
Make certain these patches have been installed before you install the Ridgeline server software.
For the most current information on required patches, see the Ridgeline Release Notes that accompanies your Ridgeline software, or go to the Extreme Networks web site at www.extremenetworks.com
.
Setting the Run Level for Linux
On Linux systems, in order for the Ridgeline database and server components to start automatically at system boot, the run level on the server must be set to 5.
Installing the Ridgeline Server
To install the Ridgeline server, complete the following steps:
1 Download the Ridgeline software from the Extreme Networks eSupport software download page.
2 Extract the contents of the zip or tar file into a temporary directory, if necessary. For information about downloading the software, refer to
Chapter 2, “Downloading Ridgeline Software.”
3 To start the installation wizard, launch the Ridgeline installer executable that you downloaded.
Figure 11: Ridgeline Welcome
Ridgeline Installation and Upgrade Guide
23
Chapter 3: Installing the Ridgeline 3.1 Server
4 The Ridgeline Software license agreement opens. After you read the agreement, click Accept to consent then click Next to proceed.
Figure 12: License Agreement
Figure 13: Solaris Non-Support Notice
24
Ridgeline Installation and Upgrade Guide
Installing the Ridgeline Server
When Ridgeline Detects Other Versions of Ridgeline
If Ridgeline detects Ridgeline 3.1 is already installed, you are instructed to uninstall it before reinstalling
Ridgeline 3.1 again.
Figure 14: Ridgeline 3.1 is Already Installed
If Ridgeline detects an older version of Ridgeline or EPICenter, the previous versions are listed, along with their installed location. This can be the case if you are upgrading to Ridgeline 3.1 from an older
version, as shown in Figure 15 .
Ridgeline Installation and Upgrade Guide
25
Chapter 3: Installing the Ridgeline 3.1 Server
Figure 15: Other Ridgeline or EPICenter Services are Running
Click Next to continue the installation.
26
Ridgeline Installation and Upgrade Guide
Installing the Ridgeline Server
If Ridgeline Does Not Support a Platform
If Ridgeline detects a platform it does not support, the Platform not supported dialog opens. See
Figure 16: Platform Not Supported
Ridgeline Installation and Upgrade Guide
27
Chapter 3: Installing the Ridgeline 3.1 Server
Choosing Ridgeline Installation Settings
The Ridgeline installer provides a choice of installation settings. You can use the recommended values for all settings, or supply custom values of your own.
Figure 17: Installation Settings
● If you choose Recommended settings, the installation process skips the custom setup steps, and
proceeds to “Software Installation” on page 33 .The default installation directories are:
C:
\Program Files\Extreme Networks\Ridgeline 3.1 for Windows, or
/opt/ExtremeNetworks/Ridgeline3.1
for Linux or Solaris.
● If you choose Custom settings, a sequence of dialogs open, starting with the directory path for
Ridgeline installation described in the following section.
1 Select the desired option and click Next.
Destination Path for Ridgeline
When you choose Custom Settings, the first choice is the destination path where you want to install
Ridgeline.
Ridgeline Installation and Upgrade Guide
28
Installing the Ridgeline Server
1 To set up a custom directory, type the directory path, or browse to find the directory where you want to install Ridgeline. See
.
Figure 18: Installation Destination
2 Click Next to continue. Or, click Restore Default Folder to reset the installation path to the default.
Ridgeline Installation and Upgrade Guide
29
Chapter 3: Installing the Ridgeline 3.1 Server
Starting Windows Services
To start services automatically when Windows starts, check the box. This is the default.
To start services manually, click the check mark to remove it.
Figure 19: Windows Services Startup
30
Ridgeline Installation and Upgrade Guide
Installing the Ridgeline Server
Setting IP Address
The Ridgeline server provides several options for IP communications with Ridgeline clients and network devices, as shown in
.
Figure 20: Setting IP Address
1 Choose the desired IP Address option:
● Use this IP address to launch the clients and to talk to the network devices.
●
Open the drop down menu to choose an IP address. The drop down menu shows the IP address for each interface on the host. With this choice Ridgeline uses a single interface to communicate with both Network clients and network devices.
Use this host name to launch the clients.
●
The server host name is displayed. When you choose this selection, Ridgeline clients communicate with the Ridgeline server using the hostname, and Ridgeline determines the interface to use when talking to network devices
Use this host name to launch the clients and this IP address when talking to network devices.
The server host name is displayed, along with a drop down menu to choose an IP address. This option is only present on hosts with multiple network interfaces.
2 Set the HTTP port that clients should use when connecting to Ridgeline. The Ridgeline default HTTP port is 8080.
3 Choose Next to continue.
Ridgeline Installation and Upgrade Guide
31
Chapter 3: Installing the Ridgeline 3.1 Server
Automatic Updates to Ridgeline
Ridgeline automatically searches for updates and installs them on the server.
Default Ports Already in Use
Ridgeline automatically installs the server software on specified ports:
• 3873
• 8009
• 8083
• 10550
• 10553-6
• 10559
If recommended ports are in use, a dialog lists these port numbers.
Figure 21: Ports in Use
To specify unused ports, complete the following steps:
1 Click Previous until you open the Installation settings dialog.
2 Choose Custom settings
3
Enter a different path as described in “Destination Path for Ridgeline” on page 28 .
Ridgeline Installation and Upgrade Guide
32
Installing the Ridgeline Server
Software Installation
1 After you have specified all installation options, and optionally migrated the previous database, the
Pre-installation Summary opens.
Figure 22: Pre-installation Summary For Windows
Figure 23: Pre-installation Summary For Linux
2 Click Install. The installation process begins.
Ridgeline Installation and Upgrade Guide
33
Chapter 3: Installing the Ridgeline 3.1 Server
NOTE
Ridgeline automatically stops the services for the server and database engine See
“Stopping the Server on Linux or Solaris” on page 44
for manual shutdown instructions.
The following dialog shows the installation progress.
Figure 24: Installation Progress
34
Ridgeline Installation and Upgrade Guide
Installing the Ridgeline Server
Database Migration
1 Choose Yes to migrate the previous database, or No to continue without migrating. If you choose
No, the installer skips to “Software Installation Successful” on page 38 .
Figure 25: Database Migration
2 Click Next to continue.
Ridgeline Installation and Upgrade Guide
35
Chapter 3: Installing the Ridgeline 3.1 Server
3 Choose the Migrate option to have the Wizard migrate the database automatically, or the Import option if you want to use database files previously archived. This procedure demonstrates the
Migrate option. Click Next to continue.
Figure 26: Database Migration Options
4 Verify the locations of the previous and current Ridgeline installations and click Migrate to continue.
The migration begins and progress is displayed.
Figure 27: Database Migration Assistant Setup
36
Ridgeline Installation and Upgrade Guide
Figure 28: Database Migration Assistant Progress
Installing the Ridgeline Server
5 When migration is 100% complete, click Close. The successful migration dialog is then displayed.
Additional information about the previous installation is displayed, along with any special instructions.
Figure 29: Database Migration Success
6 Record any onscreen instructions and click Next to complete the migration. The database migration notice dialog is displayed.
Ridgeline Installation and Upgrade Guide
37
Chapter 3: Installing the Ridgeline 3.1 Server
Figure 30: Database Migration Notice
Software Installation Successful
When the software installation is complete, the following dialog is displayed.
Figure 31: Installation Successful
Click Next to continue.
38
Ridgeline Installation and Upgrade Guide
Installing the Ridgeline Server
FTP Server for VM Tracking
The following dialog can inform you that VM tracking requires an FTP server to be up and running if you use this feature. Click Next.
Figure 32: FTP Server for VM Tracking Reminder
1 Be sure the FTP server is started.
2 Click Next to complete the installation process.
Ridgeline Installation and Upgrade Guide
39
Chapter 3: Installing the Ridgeline 3.1 Server
Ridgeline Installation Complete
A dialog opens that informs you that the installation is complete and shows the path where Ridgeline is installed. For Windows, it prompts you to restart your system. You must restart your system before a client can connect to the Ridgeline server.
Figure 33: Installation Complete
For Windows installations, click Next to continue. For Linux or Solaris, click Done.
Windows System Restart
For Windows installations, choose to restart your system immediately, or to manually restart your system later. The default is to restart your system immediately. Click Done.
Viewing Installation Logs
After the installation is complete, details about the installation process are in log files in the following locations:
●
●
●
Windows: <installed directory>\Logs
Linux: <installed directory>/Logs
Solaris: <installed directory>/Logs
Ridgeline Installation and Upgrade Guide
40
Adding or Upgrading a License Key
Launching the License Manager
Launch the License Manager and install your Ridgeline licenses. You can do this at any time after you have installed the Ridgeline server. The server can be running while you do this, but this is not required. See
“Adding or Upgrading a License Key”
for more detailed instructions.
Adding or Upgrading a License Key
To install an evaluation or permanent license for Ridgeline, or to upgrade an evaluation license to a permanent license you must run the License Manager. Until you install a license, no client will be able to connect to the Ridgeline server.
NOTE
You must install a Base 50 license key even if you have purchased additional 50-node or 250-node license keys. The Base 50 license gives you access to the Ridgeline server; the optional upgrade licenses enable you to manage additional devices.
To install or upgrade a license, complete the following steps:
1 Run the License Manager:
●
●
In Windows, from the Start menu, select Start > Programs > Extreme Networks > Ridgeline 3.1
> License Manager
On Linux or Solaris, go to the Ridgeline installation directory and run LicenseManager. By default, the Ridgeline installation directory is /opt/ExtremeNetworks/Ridgeline3.1 .
On Linux, the License Manager symbolic link is found in /root/ExtremeNetworks/
Ridgeline3.1/License Manager .
On Solaris, the License Manager is also available in Administrative Tools. Select Administrative
Tools > Extreme Networks > Ridgeline > License Manager .
Ridgeline Installation and Upgrade Guide
41
Chapter 3: Installing the Ridgeline 3.1 Server
The License Manager window opens:
Figure 34: License Key Manager
2 Enter the 14-character license key(s) in the appropriate fields, and click Install License.
A pop-up window tells you whether the installation was successful or not.
Adding a License for an Upgrade Product
When you purchase a product upgrade option such as a 50-node license or an Advanced Services licenses, you receive a separate key to enable Ridgeline to manage additional devices or unlock additional features. To add the license key for a Ridgeline upgrade, run the License Manager as described above.
Starting and Stopping the Ridgeline Server
By default, the Ridgeline server components installed as services (in Windows) or daemons (in Linux or
Solaris) are started automatically when you start or restart your computer.
If you elected not to restart your computer at the end of the installation process, then you must start the
Ridgeline database and server manually.
In Windows, if you selected the option to start the Ridgeline server components manually, then you must start them before running Ridgeline.
Ridgeline Installation and Upgrade Guide
42
Starting and Stopping the Ridgeline Server
Starting the Server on Windows
To start or restart the Ridgeline services manually, do the following in the specified order:
1 Open the Services window (found under Administrative Tools in the Control Panel).
2 Highlight Ridgeline 3.1 Database Engine, right-click and select Start from the pop-up menu to start the Ridgeline database.
3 Start the Ridgeline 3.1 Server and Ridgeline 3.1 FreeRADIUS Server in the same manner.
Stopping the Server on Windows
To stop the Ridgeline server:
1 Open the Services window (found in Administrative Tools in the Control Panel).
2 Highlight Ridgeline 3.1 Server, right-click and select Stop to stop the Ridgeline server. This should be done while the database is still running.
3 Highlight the Ridgeline 3.1 Database Engine and Ridgeline 3.1 FreeRADIUS Server in the same manner, right-click and select Stop.
Linux and Solaris Command Summary
The following table summarizes the Linux and Solaris commands for controlling Ridgeline.
Table 2: Linux and Solaris Startup and Shutdown Commands for Ridgeline 3.1
Command
RidgelineDB31 start
RidgelineDB31 stop
RidgelineServer31 start
RidgelineServer31stop
RidgelineServer31status
Function
Start RidgelineDB
Stop RidgelineServer if running, then stop RidgelineDB
Otherwise, simply stop
RidgelineDB.
Start RidgelineDB first, if not running, then start RidgelineServer
Stop RidgelineServer
Display RidgelineServer status
RidgelineServer31stop Stop RidgelineServer
RidgelineFreeRadius31 start Start RidgelineFreeRadius
RidgelineFreeRadius31 stop Stop RidgelineFreeRadius
Usage
None
Use this command only when
RidgelineServer is completely shutdown.
See the RidgelineServer31 status command.
Although this command stops the
RidgelineServer first if it is currently running, a clean RidgelineServer shutdown before the RidgelineDB shutdown cannot be assured.
RidgelineDB must be running before
RidgelineServer can start.
Use RidgelineServer status to verify that the service is fully stopped.
Use this command to determine whether the RidgelineServer is running or not, and to verify that it is completely shutdown after issuing RidgelineServer31 stop.
None
None
None
Ridgeline Installation and Upgrade Guide
43
Chapter 3: Installing the Ridgeline 3.1 Server
Starting the Server on Linux or Solaris
To start or restart the Ridgeline daemons manually, complete the following steps:
● Enter the following commands in the order shown:
/etc/init.d/RidgelineDB31 start
/etc/init.d/RidgelineServer31 start
/etc/init.d/RidgelineFreeRadius31 start
You must have administrative rights to access init.d files.
Stopping the Server on Linux or Solaris
To stop the Ridgeline server, enter the following commands:
● Enter the following commands in the order shown:
/etc/init.d/RidgelineServer31 stop
(kills the server daemon)
/etc/init.d/RidgelineServer31 status (repeat until Ridgeline server PID is stopped)
/etc/init.d/RidgelineDB31 stop (kills the database daemon)
/etc/init.d/RidgelineFreeRadius31 stop
Configuring the Ridgeline Server for NATed Client
Connections
If clients will be connecting to the Ridgeline server through a connection that uses Network Address
Translation (NAT), configure the Ridgeline server as follows:
1 Stop the Ridgeline server if it is currently running. See the previous section for information about how to do this.
2 Set the EPICENTER_SERVER_ADDRESS environment variable to the hostname of the Ridgeline server.
3 Open the runserver.sp
file, which resides in <Ridgeline_install_dir>/jboss/bin , and add the following entry: remoting.bind_by_host=true
4 In Ridgeline, set the TCP port number that clients use to connect to the Ridgeline server to 56983. To do this, go to Ridgeline Administration, click the Server Properties tab, select Other from the dropdown list, and enter 56983 in the Client Port field.
5 On the client machine, make sure the hostname of the Ridgeline server resolves to the correct outside
IP address of the server.
If the server’s IP address does not resolve correctly, add an entry for the server in the client’s hosts file. In Windows, the hosts file is c:\windows\system32\drivers\etc\hosts (where c: is the drive where Windows is installed). In Solaris and Linux, the hosts file is /etc/hosts .
6 Ensure that the ports used by Ridgeline are accessible through your firewall/NAT setup. Ridgeline uses the following ports:
Ridgeline Installation and Upgrade Guide
44
Installing Ridgeline on a Multi-Homed Server
●
● jboss ports 3873, 8080 (default), and 8083, which allow the Ridgeline server to talk to the client
HTTP port 8334, which allows switches to talk to the Ridgeline server in HTTPs mode
●
●
FreeRADIUS port 10559 (default)
TCP port 56983 for the client to connect to the server in NAT-enabled environments
7 Restart the Ridgeline server, as described in the previous section.
Installing Ridgeline on a Multi-Homed Server
A multi-homed server has more than one network interface card (NIC) installed and might be using multiple IP addresses. If you are installing Ridgeline on a multi-homed server, you must specify either the IP address or hostname that Ridgeline clients should use when communicating to the Ridgeline server. You also specify which IP address Ridgeline should use when communicating with managed devices, or simply let Ridgeline choose the IP address automatically.
Ridgeline 3.1 provides a Ridgeline Server Setup Utility that simplifies the process of configuring
Ridgeline interfaces. The configuration options are:
●
●
●
Select a single IP address for communication with Ridgeline clients and network devices. Other host
IP addresses are unused by Ridgeline. Although this is a valid Ridgeline setting, and is presented in the setup utility, it is not useful for multi-homed systems because it only utilizes a single interface.
Set a hostname that Ridgeline clients can use to communicate with the Ridgeline server, and let
Ridgeline choose the IP address to communicate with network devices.
Set a hostname that Ridgeline clients can use to communicate with Ridgeline, and specify an IP address that Ridgeline uses to communicate with network devices.
To configure Ridgeline for multi-homed servers:
1
Stop the Ridgeline server. See “Starting and Stopping the Ridgeline Server” on page 42
.
2 Start the Ridgeline Server Setup Utility:
● On a Windows system, from the Start menu go to:
Programs > Extreme Networks > Ridgeline3.1 > Server Setup Utility
● On Linux, the server setup utility from symbolic link is in /root/ExtremeNetworks/
Ridgeline3.1/Server Setup Utility .
The Ridgeline Server Setup Utility dialog box opens.
Ridgeline Installation and Upgrade Guide
45
Chapter 3: Installing the Ridgeline 3.1 Server
Figure 35: Ridgeline Server Setup Utility
3 Choose one of the setup options:
-
Use this IP address to launch the clients and to talk to the network devices.
This selection is not relevant for a multi-homed system, because it only specifies a single interface for all communications.
-
Use this host name to launch the clients.
If you choose this option, clients should use the displayed hostname to communicate with Ridgeline. Ridgeline will determine which IP address to use to communicate with network devices.
-
Use this host name to launch the clients and this IP address to talk to the network devices.
If this is selected, clients should use the displayed hostname to communicate with Ridgeline, and choose an IP address from the drop-down list for network device communication.
4 Optionally, specify a different HTTP port.
5 Click Confirm. A confirmation dialog is displayed.
6 Click OK on the confirmation dialog, then close the setup utility.
7 Start the Ridgeline server.
Ridgeline Installation and Upgrade Guide
46
Installing a Difference Viewer
Installing a Difference Viewer
Ridgeline provides a Diff feature that allows you to compare configuration files using a Difference
Viewer. This feature requires that a Difference Viewer be installed on the client system. A Difference
Viewer can automatically compare and highlight the differences between two files. The Diff feature does not work with a standard text editor.
You can use any Diff viewer that is installed on the system where your Ridgeline client is running.
Select Difference Viewer from the Tools menu to tell Ridgeline the location of the viewer. If you do not have a Diff viewer already installed, you must install one on your client system in order to use the Diff feature.
For Windows. You can obtain a Diff viewer from the following sources:
● WinMerge.exe
; downloadable from http://winmerge.sourceforge.net
● Araxis Merge ; 30 day free trial evaluation downloadable from http://www.araxis.com
For Linux or Solaris. sdiff (in
/usr/bin/sdiff
) is assumed as the default Diff viewer.
Enabling SSH for Secure Communications
By default, the Ridgeline server communicates to the devices it manages using unencrypted access, and unencrypted file transfers. In addition, the communications between the Ridgeline server and its clients are also unencrypted by default.
● By installing an SSH enabling key, you can use SSH2 instead of Telnet to communicate to the devices
Ridgeline manages, and securely upload and download configuration files to and from your Extreme devices.
● By installing an SSH2 server co-resident with the Ridgeline server, and by installing SSH2 clients on the systems where your Ridgeline clients reside, you can use SSH2 to encrypt the communications between the Ridgeline server and Ridgeline clients. See the Appendix in the Ridgeline Service Advisor
Concepts and Solutions Guide for details on setting up secure client-server communication.
There are three requirements for enabling Ridgeline to use SSH2 to communicate with the devices it manages:
● The Ridgeline SSH enabling key must be installed. Due to export restrictions, you must obtain this module from Extreme Networks. It is not included with the Ridgeline software distribution.
●
●
Your switches must be running versions of ExtremeWare or ExtremeXOS that support SSH, and SSH must be enabled on those devices. Due to export restrictions, a special license is required.
To request versions of ExtremeWare or ExtremeXOS that support SSH, contact Extreme Networks
Technical Support.
SSH must be enabled in Ridgeline for the devices to which you want to communicate using SSH.
NOTE
If the SSH enabling key is not installed in the Ridgeline directory, you will not be able to configure SSH in Ridgeline. The relevant fields will be grayed out.
Ridgeline Installation and Upgrade Guide
47
Chapter 3: Installing the Ridgeline 3.1 Server
The Ridgeline SSH Enabling Key
Ridgeline’s SSH2 capability can be enabled by installing the Ridgeline SSH enabling key. This module must be downloaded from Extreme Networks, as it is subject to export restrictions. It is not provided with the Ridgeline software distribution.
The SSH2 capability uses strong encryption, so prior to downloading the enabler module you must provide certain information to Extreme Networks in order to confirm compliance with the export regulations administered by the Bureau of Industry and Security under the U.S. Department of
Commerce.
To obtain the SSH enabling key, fill out the End-User Certification Form at: http://www.extremenetworks.com/apps/EPICenter/ssh.asp
●
●
After you submit the form, Extreme Networks performs a review and responds to you, generally within two business days.
If the information you provided conforms to the applicable export regulations, you receive an email with the information needed to obtain the SSH enabling key file. Unzip and place the SSH enabling key file in your existing Ridgeline installation directory to unlock the Ridgeline SSH2 features.
NOTE
The file “ssh-enabler” must be installed without a file extension.
● If the information you provided does not conform to the export regulations, you will receive an email indicating a denial of acceptance.
The SSH enabling key must be placed in the top-level Ridgeline installation directory (by default
\Program Files\Extreme Networks\Ridgeline 3.1
in Windows, or /opt/ExtremeNetworks/
Ridgeline3.1
under Solaris or Linux).
Uninstalling the Ridgeline Server Software
The following sections describe how to uninstall the Ridgeline server software.
For information on uninstalling a Service Pack patch in order to revert to your previously installed
version of Ridgeline software, see “Uninstalling the Service Pack on Windows Systems” on page 66
or
“Uninstalling the Service Pack on Solaris or Linux Systems” on page 72 .
Uninstalling the Server on Windows
An Uninstall utility is provided in the Windows Start menu. This utility removes all the currentlyinstalled components of the Ridgeline server. It also removes some of the supporting files, and asks about removing certain files that it detects have been modified since installation.
To uninstall Ridgeline server components, compete the following steps:
1 Shut down the Ridgeline server components if they are still running.
2 Exit all clients.
Ridgeline Installation and Upgrade Guide
48
Uninstalling the Ridgeline Server Software
3 From the Start Menu, go to Programs > Extreme Networks > Ridgeline 3.1 > Uninstall to start the uninstall wizard. This dialog informs you that this process will remove Ridgeline.
Figure 36: Uninstall Wizard
4 Click Next. The uninstall options dialog opens and asks you to confirm the Ridgeline uninstall and asks if you want to remove logs, database, and backups. You can choose to remove everything or leave everything behind which will remove the program but not these data components.
Ridgeline Installation and Upgrade Guide
49
Chapter 3: Installing the Ridgeline 3.1 Server
Figure 37: Uninstall Options
5 Click Uninstall. The uninstall process begins and the next dialog shows the progress.
50
Ridgeline Installation and Upgrade Guide
Figure 38: Uninstall Progress
Uninstalling the Ridgeline Server Software
6 When the process completes, the dialog informs you that the uninstall was successful. You can choose to restart your system immediately or manually restart the system at a later time.
7 Select your choice, then click Done to close the wizard. If you choose Yes, restart my system, the system immediately shuts down then restarts.
8 If the uninstall process cannot remove Ridgeline items. The dialog lists these. Choose a restart option.
9 Click Done to close the wizard.
Ridgeline Installation and Upgrade Guide
51
Chapter 3: Installing the Ridgeline 3.1 Server
Figure 39: Items Were Not Removed
Uninstalling the Server on Linux or Solaris
To remove the Ridgeline server software, follow these steps:
1 Stop the Ridgeline server components if they are running. See
“Stopping the Server on Linux or
2 Exit all clients.
3 On Linux, the uninstall wizard has a symbolic link in /root/ExtremeNetworks/Ridgeline3.1/
Uninstall Ridgeline 3.1
.
On Solaris, the Ridgeline uninstall Wizard is also available under Administrative Tools. Select
Administrative Tools > Extreme Networks > Ridgeline > Uninstall Ridgeline
4 Follow the onscreen instructions to uninstall the software.
If you plan to re-install the Ridgeline server, you should restart your system before you attempt to re-install.
The Ridgeline software is now completely uninstalled.
Viewing Uninstall Logs
After the uninstall is complete, details about the uninstall process are contained in log files in the following locations:
●
●
●
Windows: desktop
Linux: desktop
Solaris: desktop
Ridgeline Installation and Upgrade Guide
52
4
Launching the Ridgeline 3.1
Client
C H A P T E R
This chapter describes how to connect to the Ridgeline 3.1 server and launch the Ridgeline 3.1 client software, and includes the following sections:
●
●
●
●
About the Client Initialization Process on page 53
Launching the Client Application on page 53
Disabling Installation of Desktop Shortcuts on page 56
Configuring the Firefox Browser for the Java Plug-In on page 57
About the Client Initialization Process
The Ridgeline client initialization process makes use of Java Web Start technology. Java Web Start allows you to obtain files necessary to run the Ridgeline client directly from the Ridgeline server by pointing a browser to the Ridgeline server and clicking on a hyperlink. The download and installation of the
Ridgeline software on the client system takes place automatically.
Each time you launch the client, Ridgeline checks whether you have the most current software version.
If you do not, Ridgeline automatically updates the client files on your system.
Client initialization using Java Web Start requires that the client system have a certain version of the
Java plug-in installed. If the client system does not have this required Java version, then you are directed to a location where you can download the correct version.
Launching the Client Application
The Ridgeline client application can be launched on systems running one of the following operating environments:
● Microsoft Windows Vista, Windows XP Professional with SP1 or later, Windows 2003 server,
Windows 2008 server, or Window 7 (Ridgeline 32-bit version only) running on an Intel Pentiumcompatible CPU
● or
Red Hat Enterprise Linux Version 5 or
Ridgeline Installation and Upgrade Guide
53
Chapter 4: Launching the Ridgeline 3.1 Client
● Solaris 10
NOTE
This release, Ridgeline 3.1 will be the last release that supports Solaris.
A Ridgeline client requires a monitor that supports 1024 x 768 resolution, and at least 16-bit color. Your system display settings must be set for at least 65536 colors.
See
“System Requirements” on page 7
for memory, CPU, disk and other requirements.
NOTE
There is no separate installation for the client. When you launch the client, any software updates are downloaded from the server and installed automatically.
To launch the client, you need to have the following information:
● The name or IP address of the Ridgeline server to which the client should connect
● The HTTP port that the client uses to communicate with the server (the default is 8080). This is the
HTTP port you entered when you installed the Ridgeline server.
To launch the Ridgeline client, complete the following steps:
1 Launch your web browser.
2 Enter the URL for your Ridgeline server, in the form: http://<host>:<port>/
Replace
<host>
with the name or IP address of the system where the Ridgeline server is running.
Replace
<port>
with the TCP port number that you assigned to the Ridgeline web server during installation.
NOTE
If you configured your Ridgeline server to use the default web server port 80, you do not need to include the port number. However, the port used by Ridgeline is 8080 by default, so in most cases you do need to include the port.
Ridgeline Installation and Upgrade Guide
54
3 The Ridgeline Welcome page appears.
Figure 40: Ridgeline Welcome Page
Launching the Client Application
4 Click the Log on to Ridgeline link.
5 Ridgeline checks if your system is running the correct version of the Java plug-in. If you are not running the correct version, you are directed to a page where you can download the correct version.
If you are running the correct version of the Java plug-in, the Ridgeline client software is downloaded from the Ridgeline server and installed on the local system.
6 (Optional) If you running the Microsoft System Center Virtual Machine Manager (SCVMM), you must install the Ridgeline XNV agent on the SCVMM host. You can download the Ridgeline XNV agent from the Ridgeline Welcome page by clicking “Get Ridgeline XNV agent here” and following the instructions on the agentInstaller.exe dialog box.
7 After the software is downloaded, you are prompted whether you want to run the application. Click
Run to continue.
Ridgeline Installation and Upgrade Guide
55
Chapter 4: Launching the Ridgeline 3.1 Client
8 The Ridgeline Log On screen appears, and you are prompted for a username and password.
Figure 41: Ridgeline Log On Screen
9 If this is the first time you are logging in to Ridgeline, enter admin in both the Username field and the Password field. Click Log on to connect to the Ridgeline server.
10 After a successful login, the Ridgeline 3.1 Home screen appears. For instructions on using Ridgeline, see the Ridgeline Reference Guide, or the online help.
Disabling Installation of Desktop Shortcuts
As part of the Ridgeline client initialization process, a shortcut may be installed on your desktop. The desktop shortcut allows you to start the client without having to point a browser to the server (and clicking the Log on to Ridgeline link). Installation of the desktop shortcut assumes that the Java setting for Shortcut Creation is set to the default of Prompt user if hinted.
You can optionally change the Shortcut Creation setting so that a shortcut is not installed with the
Ridgeline client. To do this:
1 From the Control Panel (Start > Settings> Control Panel) double-click the Java icon.
2 When the Java Plug-In control panel appears, click the Advanced tab.
3 Expand the list of items next to Shortcut Creation.
Ridgeline Installation and Upgrade Guide
56
Configuring the Firefox Browser for the Java Plug-In
4 Change the setting to Never allow.
Figure 42: Modifying the Java Shortcut Creation Setting
5 Click OK to apply the setting and close the Java Plug-In control panel.
Configuring the Firefox Browser for the Java Plug-In
If you plan to use the Mozilla Firefox browser to connect to the Ridgeline server, you must download and install the Java Runtime Environment (JRE) plug-in, and then link it to the Firefox browser. These are two separate steps. Until you do this, you will not be able to log into Ridgeline using Firefox.
To download and install the JRE plug-in, go to the Sun web site at: http://www.java.com/en/download/manual.jsp
For Windows, you can download either the Online or Offline versions. For Solaris, download the 32-bit version. For Linux, download the self-extracting file (not the RPM version).
For installation instructions, click the Instructions link to the right of the download button.
Ridgeline Installation and Upgrade Guide
57
Chapter 4: Launching the Ridgeline 3.1 Client
After the plug-in is installed, you must configure and enable the JRE to run applets in your browser.
You can find the instructions in one of two ways:
●
●
On the Installation Instructions page, click the “Enable and Configure” link near the top of the page.
You can also go directly to these instructions at the following URLs:
For Windows: http://www.java.com/en/download/help/5000010400.xml#enable
For Linux: http://www.java.com/en/download/help/5000010500.xml#enable
For Solaris: http://www.java.com/en/download/help/5000010600.xml#enable
Follow the instructions to create a symbolic link to the JRE libjavaplugin_oji.so
file, and to enable
Java under your browser preferences.
58
Ridgeline Installation and Upgrade Guide
5
Upgrading the Ridgeline
Software
C H A P T E R
This chapter describes how to upgrade the Ridgeline software, and includes the following sections:
●
●
●
●
●
●
Ridgeline Software Upgrade Overview on page 59
Installing a Service Pack Release on page 60
Uninstalling the Service Pack on Windows Systems on page 66
Uninstalling a Service Pack from the Windows Control Panel on page 70
Installing a Service Pack on Solaris or Linux Systems on page 71
Uninstalling the Service Pack on Solaris or Linux Systems on page 72
Ridgeline Software Upgrade Overview
The Ridgeline software is available in the following forms. You can select which one to install based on the circumstances under which you want to upgrade:
●
●
Base installation.
To upgrade to a new software release, install the new version of the software after downloading it from the Extreme Networks web site.
As long as you install the software into a different directory, the two versions can co-exist. See
Service Pack.
Service Packs are minor releases that may add new features to Ridgeline, as well as provide fixes for known problems from previous releases. A Service Pack release is made available as a patch that can be installed over an existing Ridgeline installation.
If you already have the Ridgeline software installed on your system when a Service Pack is released, you can upgrade the software by installing the patch bundle for the Service Pack; you do not need to reinstall the full product. See
“Installing a Service Pack Release” on page 60
for information.
If you do not already have the Ridgeline software installed on your system, to install the Service
Pack, you must first install the base Ridgeline release, then install the patch bundle for the Service
Pack.
Ridgeline Installation and Upgrade Guide
59
Chapter 5: Upgrading the Ridgeline Software
summarizes the options for installing and upgrading the Ridgeline software.
Table 3: Ridgeline Installation and Upgrade Options
Release Type Contents
Base Ridgeline
Installation
Major Ridgeline software release
Service Pack New features and software fixes
Available Formats When to Install How to Install
• Large file downloadable from the
Extreme Networks web site
• Smaller file that installs on top of an existing Ridgeline installation and integrates the Service
Pack features and fixes into the existing installation.
You want to perform a fresh Ridgeline installation/upgrade to a new major release.
See
Ridgeline software to upgrade to a permanent license.” on page 22 .
You already have a base Ridgeline software release installed and you want to install the
Service Pack features and fixes.
See
.
Installing a Service Pack Release
From time to time, Extreme Networks releases updates to the current Ridgeline software as Service
Packs. Service Packs are minor releases that provide fixes for known problems from previous releases.
A Service Pack is released as a software patch that integrates the Service Pack fixes into an existing
Ridgeline installation. If you already have the Ridgeline software installed on your system when a
Service Pack is released, you can add the Service Pack updates by installing the patch release.
You can install a Service Pack release only on top of an existing base version of the same Ridgeline release. If you are still running the previous major release, you cannot install the Service Pack release.
Instead, you must first install the full-installation version of the base version software. Follow the
normal installation instructions under “Installing the Ridgeline Server” on page 23
.
To summarize, upgrading to a Ridgeline Service Pack release consists of the following steps:
1 Install the base version of the Ridgeline software (if it is not already installed).
2 Install the Ridgeline Service Pack.
NOTE
It is strongly recommended that you backup your Ridgeline database before installing a Service Pack. If you need to uninstall the Service Pack and revert to the previous release for any reason, you will need to restore the database as it was prior to the upgrade. Migrating the database is not supported in Service Pack release. You must first migrate the database to a major release before installing the Service Pack.
Ridgeline Installation and Upgrade Guide
60
Installing a Service Pack Release
NOTE
You cannot upgrade a Ridgeline beta release using this method. You must uninstall the beta release and then install the full Ridgeline release.
Installing a Service Pack on Windows Systems
Before you install a Ridgeline Service Pack, back up your database.
NOTE
We strongly recommend that you disable any anti-virus software before performing the Ridgeline installation. Anti-virus software might interfere with Sybase database upgrade.
To install a Ridgeline Service Pack release on a Windows system, follow these steps:
1 Download the Ridgeline Service Pack software from the Extreme Networks eSupport software download page.
Ridgeline detects the platform you are using.
2 Shut down the Ridgeline 3.1 services if still running before installing the software.
3 Extract the contents of the zip or tar file into a temporary directory. For information about downloading the software, refer to
Chapter 2, “Downloading Ridgeline Software.”
The extraction process puts the files in a directory named sp<n>win/patch<n> where <n> is a number related to the Service Pack under the directory you select. Folder names should be used when you perform the extraction.
4 To start the wizard, double-click on the downloaded Service Pack installer executable file.
If running, stop the Ridgeline services (the server and database engine). See
Windows” on page 43 for instructions.
Ridgeline checks the system for a Ridgeline software version. If it does not detect Ridgeline on your system the “Cannot find any Ridgeline Installation dialog” opens and states that “We are not able to continue because Ridgeline is not installed.”
5 Click Next. The installation wizard welcome dialog opens. It recommends that you quit all programs before you continue to install the software.
Ridgeline Installation and Upgrade Guide
61
Chapter 5: Upgrading the Ridgeline Software
Figure 43: Ridgeline SP Introduction
62
Ridgeline Installation and Upgrade Guide
Installing a Service Pack Release
The Ridgeline Software License Agreement dialog displays.
6 If you agree to the terms of the Ridgeline Software License Agreement, click the button to accept the
License Agreement, then click Next.
Figure 44: Ridgeline Software License Agreement
7 Click OK to continue.
8 Click Next.
Ridgeline Installation and Upgrade Guide
63
Chapter 5: Upgrading the Ridgeline Software
The pre-installation summary opens where you can verify the path for the Service Pack. Ridgeline automatically searches for the path.
Figure 45: Pre-Installation Summary
9 Click Install.
64
Ridgeline Installation and Upgrade Guide
Installing a Service Pack Release
The Service Pack Progress Indicator displays to show what is happening with the software installation and to show the progress of the software installation.
Figure 46: Service Pack Installation Progress Indicator
Ridgeline Installation and Upgrade Guide
65
Chapter 5: Upgrading the Ridgeline Software
When the installation process is complete, the dialog informs you that the Service Pack installation was successful.
Figure 47: Service Pack Installation Successful
Viewing Installation Logs
After the installation is complete, detailed information about the installation process is stored in log files in the following locations:
●
●
●
Windows — <installed directory>\Logs
Linux — <installed directory>\Logs
Solaris — <installed directory>\Logs
Ridgeline Installation and Upgrade Guide
66
Uninstalling the Service Pack on Windows Systems
Uninstalling the Service Pack on Windows Systems
NOTE
Please make sure you restore your previously backed-up database (backed up prior to installing the service pack) after uninstalling the service pack, to completely restore Ridgeline to its previous state.
If you need to uninstall the Service Pack release, complete the following steps:
1 Shut down the Ridgeline services (Ridgeline 3.1 Database, Ridgeline 3.1 Server and Ridgeline 3.1
FreeRADIUS Server) if still running. (See “Stopping the Server on Windows” on page 43
for detailed information).
2 Go to the directory in which Ridgeline 3.1 is installed (Ridgeline 3.1 Home/
_Ridgeline3_1_SP1_Installation).
3 Run the binary file with name Uninstall Ridgeline 3.1 Service Pack 1.exe.
Ridgeline Installation and Upgrade Guide
67
Chapter 5: Upgrading the Ridgeline Software
The Uninstall Ridgeline SP1 wizard opens.
Figure 48: Ridgeline About To Uninstall
4 Click Uninstall.
68
Ridgeline Installation and Upgrade Guide
Uninstalling the Service Pack on Windows Systems
As the software is uninstalled, the uninstall progress window displays showing the files and features being removed and a progress bar.
Figure 49: Ridgeline Uninstall Progress
Ridgeline Installation and Upgrade Guide
69
Chapter 5: Upgrading the Ridgeline Software
When the uninstall process completes, a dialog confirms that the uninstall was successful.
Figure 50: Successful Ridgeline Service Pack 1 Uninstall
5 Click Done to close the wizard.
Viewing Uninstall Logs
After the installation is complete, detailed information about the uninstall process is stored in log files placed on the Desktop for Windows, Linux, and Solaris.
Uninstalling a Service Pack from the Windows
Control Panel
You can uninstall a Service Pack from the Windows Control Panel the same way you remove other programs.
1 Go to Start > Control Panel > Add or Remove Programs. The following window opens.
2 Select the Ridgeline SP and click Change/Remove.
Ridgeline Installation and Upgrade Guide
70
Figure 51: Add or Remove Programs Window
Installing a Service Pack on Solaris or Linux Systems
Installing a Service Pack on Solaris or Linux Systems
NOTE
This release, Ridgeline 3.1 will be the last release that supports Solaris.
To install a Ridgeline Service Pack release on a Solaris or Linux system, follow these steps:
1 Download the Ridgeline Service Pack software from the Extreme Networks software downloads page and extract the contents of the file into a temporary directory.
The extraction process puts the files in a directory named sp<n>sol/patch<n> (for Solaris) or sp<n>lin/patch<n> (for Linux), where <n> is a number related to the Service Pack, under the directory you select. Make sure you specify that folder names should be used when you perform the extraction.
2 Exit all Ridgeline clients.
3 Shut down the Ridgeline services and database engines if they are running (see
“Stopping the Server on Linux or Solaris” on page 44 for instructions).
4 It is recommended that you back up your database. In addition, if the database transaction log, basecamp.log
, remains in the top-level Ridgeline installation directory after the Ridgeline server has been shut down, you should save it also. (Under most circumstances basecamp.log
is removed when the server stops.)
You should also save the files basecamp.db
and epicenter.db
, which reside in the
/database/data subdirectory under the Ridgeline installation directory, as well as any database transaction log files
(for example, basecamp.log
or epicenter.log
) that reside in this directory.
Ridgeline Installation and Upgrade Guide
71
Chapter 5: Upgrading the Ridgeline Software
5 Open a command shell and change to the directory where you extracted the Service Pack files:
% cd sp<n>sol/patch<n> (for Solaris)
% cd sp<n>lin/patch<n>
(for Linux)
6 Run the script Ridgeline_31_SP1_Installer.bin
. To avoid permission errors, run the script as the same user that performed the original Ridgeline software installation.
To install the Service Pack in the default installation directory (which is /opt/ExtremeNetworks/
Ridgeline3.1/ ) enter the Ridgeline_31_SP1_Installer.bin
command without a directory name. For example:
% ./Ridgeline_31_SP1_Installer.bin
To install the Service Pack in a non-default directory that has a name that includes spaces, be sure to specify the directory name in quotes. For example:
% ./Ridgeline_31_SP1_Installer.bin "Directory With Spaces/Ridgeline3.1"
This script file calls a script that will back up Ridgeline files to <Ridgeline_install_dir>/backup
7
for instructions).
Uninstalling the Service Pack on Solaris or Linux
Systems
NOTE
Please make sure you restore your previously backed-up database (backed up prior to installing the service pack) after uninstalling the service pack, to completely restore Ridgeline to its previous state.
If you need to uninstall the Service Pack release, complete the following steps:
1 Exit all Ridgeline clients.
2 Shut down the Ridgeline services and database engines if they are running. See
“Stopping the Server on Linux or Solaris” on page 44 for instructions.
3 Go to the directory in which Ridgeline 3.1 is installed (Ridgeline 3.1 Home/
_Ridgeline3_1_SP1_Installation).
4 Open a command shell and run the binary file with name Uninstall Ridgeline 3.1 Service Pack
1.bin
.
To avoid permission errors, run the script as the same user that performed the Ridgeline 3.1 patch installation. The Uninstall Ridgeline SP1 wizard opens.
Ridgeline Installation and Upgrade Guide
72
Figure 52: Ridgeline About To Uninstall
Uninstalling the Service Pack on Solaris or Linux Systems
5 Click Uninstall.
Ridgeline Installation and Upgrade Guide
73
Chapter 5: Upgrading the Ridgeline Software
When the uninstall process completes, a dialog confirms that the uninstall was successful.
Figure 53: Successful Ridgeline Service Pack 1 Uninstall
6 AFter the uninstall has completed, click Done.
74
Ridgeline Installation and Upgrade Guide
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 Chapter 1: Installation Overview
- 5 Installation Overview
- 6 The Ridgeline Server
- 6 Upgrading the Ridgeline Server
- 6 The Ridgeline Client
- 7 System Requirements
- 7 Windows Vista/XP/2003 Server/2008 Server/Windows
- 7 The Ridgeline Server
- 8 The Ridgeline Client
- 8 Sun Microsystems Solaris
- 8 The Ridgeline Server
- 9 The Ridgeline Client
- 9 Red Hat Enterprise Linux
- 9 The Ridgeline Server
- 10 The Ridgeline Client
- 10 Browser Requirements for Launching the Ridgeline Client
- 11 Upgrading Ridgeline to a Service Pack Release
- 11 Obtaining a License Key for the Ridgeline Server
- 12 Evaluation License
- 12 Permanent License
- 13 Distinguishing Between a License Key and an Activation Key
- 13 Installing a Permanent License When an Evaluation License is Already Installed
- 15 Chapter 2: Downloading Ridgeline Software
- 15 Overview
- 16 Determining Device Serial Numbers
- 18 Providing Serial Numbers to Extreme Networks eSupport
- 21 Chapter 3: Installing the Ridgeline 3.1 Server
- 21 Installation Overview
- 22 Retaining the Database when Reinstalling Ridgeline
- 22 User Permissions
- 22 Local Name Resolution for the Server
- 23 Required Patches for Solaris
- 23 Setting the Run Level for Linux
- 23 Installing the Ridgeline Server
- 25 When Ridgeline Detects Other Versions of Ridgeline
- 27 If Ridgeline Does Not Support a Platform
- 28 Choosing Ridgeline Installation Settings
- 28 Destination Path for Ridgeline
- 30 Starting Windows Services
- 31 Setting IP Address
- 32 Automatic Updates to Ridgeline
- 32 Default Ports Already in Use
- 33 Software Installation
- 35 Database Migration
- 38 Software Installation Successful
- 39 FTP Server for VM Tracking
- 40 Ridgeline Installation Complete
- 40 Windows System Restart
- 40 Viewing Installation Logs
- 41 Launching the License Manager
- 41 Adding or Upgrading a License Key
- 42 Adding a License for an Upgrade Product
- 42 Starting and Stopping the Ridgeline Server
- 43 Starting the Server on Windows
- 43 Stopping the Server on Windows
- 43 Linux and Solaris Command Summary
- 44 Starting the Server on Linux or Solaris
- 44 Stopping the Server on Linux or Solaris
- 44 Configuring the Ridgeline Server for NATed Client Connections
- 45 Installing Ridgeline on a Multi-Homed Server
- 47 Installing a Difference Viewer
- 47 For Windows
- 47 For Linux or Solaris
- 47 Enabling SSH for Secure Communications
- 48 The Ridgeline SSH Enabling Key
- 48 Uninstalling the Ridgeline Server Software
- 48 Uninstalling the Server on Windows
- 52 Uninstalling the Server on Linux or Solaris
- 52 Viewing Uninstall Logs
- 53 Chapter 4: Launching the Ridgeline 3.1 Client
- 53 About the Client Initialization Process
- 53 Launching the Client Application
- 56 Disabling Installation of Desktop Shortcuts
- 57 Configuring the Firefox Browser for the Java Plug-In
- 59 Chapter 5: Upgrading the Ridgeline Software
- 59 Ridgeline Software Upgrade Overview
- 60 Installing a Service Pack Release
- 61 Installing a Service Pack on Windows Systems
- 66 Viewing Installation Logs
- 66 Uninstalling the Service Pack on Windows Systems
- 70 Viewing Uninstall Logs
- 70 Uninstalling a Service Pack from the Windows Control Panel
- 71 Installing a Service Pack on Solaris or Linux Systems
- 72 Uninstalling the Service Pack on Solaris or Linux Systems