Harley PS 5, PS 6 Power Seeder OPERATOR’S & PARTS MANUAL

OPERATOR’S & PARTS
MANUAL
MODEL PS5 & PS6
POWER SEEDER
SERIAL NUMBER:________________
PURCHASE DATE:________________
PS58AD002 AND UP
PS68AD005 AND UP
800-437-9779
www.paladinbrands.com
MANUAL P/N: P970750
RELEASE DATE: APRIL 30, 2008
PO Box 230, Jamestown, ND 58402-0230, United States of America
notes
PREFACE
This manual describes the installation, operation and maintenance of the Harley Power
Seeder. Read and understand the manual in its entirety before performing installation,
or maintenance in order to ensure the equipment’s optimum level of performance. Read and
follow all safety and precautionary notes included in this text.
Throughout this manual, references are made to front, back, right and left directions. These
are determined by sitting in the operator’s seat of the tractor.
REMINDER: Fill in the warranty card and mail within 10 days of your purchase date. While
filling in the card with the correct information, put the date purchased and the serial number on
the front cover of this manual. Should you need to call your dealer or Harley Attachments, this
information will help them to more quickly provide accurate service for you.
Any questions related to this should be directed to Harley Attachments customer service at
800-437-9779.
TABLE OF CONTENTS
OWNER ASSISTANCE................................................................................................................2
SPECIFICATIONS........................................................................................................................3
BOLT TORQUE CHART...............................................................................................................4
SAFETY STATEMENTS...............................................................................................................5
GENERAL SAFETY PRECAUTIONS...................................................................................... 5-7
EQUIPMENT SAFETY PRECAUTIONS.................................................................................. 7-9
SAFETY DECAL AND SERIAL TAG PLACEMENT...............................................................10-11
OPERATIONAL PROCEDURE............................................................................................ 12-16
MAINTENANCE................................................................................................................... 16-17
ASSEMBLY, PARTS IDENTIFICATION................................................................................ 18-36
WARRANTY POLICY.................................................................................................................37
MODEL PS5 & PS6
HARLEY POWER SEEDER®
OWNER ASSISTANCE
Harley Attachments, LLC and your authorized Harley dealer want you to be completely
satisfied with your investment. To resolve any problems that may occur, please contact the
Service Manager of your local Harley dealer. If your problem has not been handled to your
satisfaction, contact:
Customer Service (8:00am – 5:00pm CT)
Harley Attachments, LLC
PO Box 230
Jamestown, ND 58402-0230
701-252-9300
800-437-9779
Parts Fax: 701-952-9307
E-mail: [email protected]
Please be prepared to provide the following information:
•
•
•
•
•
Your name, address and telephone number
Machine model and SERIAL NUMBER
Dealership name and address
Machine purchase date
Nature of problem
__________________________________________________________________________
Local Dealer Information:
Contact: _______________________________________________________________
Address: _ _____________________________________________________________
Phone #1: _ ____________________________________________________________
Phone #2: _ ____________________________________________________________
E-mail: ________________________________________________________________
MODEL PS5 & PS6
HARLEY POWER SEEDER®
SPECIFICATIONS
Overall Width (A)
Overall Length (B)
Overall Height (C)
Seeding Width (D)
Weight (Empty)
with 3 Point
with Rake
HP Range (with Rake)
Category
3-Point Lift Capacity Required
at 24 Inches with Scarifier *
3-Point Lift Capacity Required
at 24 Inches with Rake *
Drum Diameter
PS5
70.5 Inches
23.75 Inches
34.75 Inches
62.75 Inches
357 lbs
462 lbs
882 lbs
16-35
1
1150 lbs
PS6
82.75 Inches
23.75 Inches
34.75 Inches
75.00 Inches
391 lbs
496 lbs
1147 lbs
30-40
1
1200 lbs
1800 lbs
2200 lbs
16.0 Inches
16.0 Inches
* Use tractor front counter weight as needed.
D
C
A
B
MODEL PS5 & PS6
HARLEY POWER SEEDER®
BOLT TORQUE CHART
After every ten (10) hours of operation, check all hardware and tighten where required.
SAE Series Torque Chart
DO NOT use these values if a different torque value or tightening procedure is listed for a specific
application. Torque values listed are for general use only.
Fasteners should be replaced with the same grade.
Make sure fastener threads are clean and you properly start thread engagement. This will
prevent them from failing when tightening.
Metric Series Torque Chart
Use only metric tools on metric hardware. Other tools may not fit properly. They may slip and
cause injury.
MODEL PS5 & PS6
HARLEY POWER SEEDER®
SAFETY STATEMENTS
DANGER
This statement is used where serious injury or death will result if the
instructions are not followed properly.
WARNING
This statement is used where serious injury or death could result if the
instructions are not followed properly.
CAUTION
This statement is used where minor injury could result if the instructions are
not followed properly.
NOTICE
This statement is used where equipment or property damage could result if
the instructions are not followed properly.
This symbol by itself or used with a safety signal word throughout this manual
is used to call your attention to instructions involving your personal safety or
the safety of others. Failure to follow these instructions can result in injury or
death.
GENERAL SAFETY PRECAUTIONS
WARNING
WARNING
READ MANUAL PRIOR TO INSTALL
Improper installation, operation, or maintenance of this equipment could result
in serious injury or death. Operators and maintenance personnel should read
this manual as well as all manuals related to this equipment and the prime
mover thoroughly before beginning installation, operation, or maintenance.
FOLLOW ALL SAFETY INSTRUCTIONS IN THIS MANUAL AND THE
PRIME MOVERS MANUAL.
READ AND UNDERSTAND ALL SAFETY STATEMENTS
Read all safety decals and safety statements in all manuals prior to
operating or working on this equipment. Know and obey all OSHA
regulations, local laws and other professional guidelines for your operation.
Know and follow good work practices when assembling, maintaining,
repairing, mounting, removing, or operating this equipment.
KNOW YOUR EQUIPMENT
Know your equipment’s capabilities, dimensions, and operations before
operating. Visually inspect your equipment before you start and never
operate equipment that is not in proper working order with all safety devices
intact. Check all hardware to assure it is tight. Make certain that all locking
pins, latches, and connection devices are properly installed and secured.
Remove and replace any damaged, fatigued, or excessively worn parts.
Make certain all safety decals are in place and are legible. Keep decals clean
and replace them if they become worn and hard to read.
MODEL PS5 & PS6
HARLEY POWER SEEDER®
WARNING
WARNING
WARNING
WARNING
PROTECT AGAINST FLYING DEBRIS
Always wear proper safety glasses, goggles, or a face shield when driving
pins in or out or when any operation causes dust, flying debris, or any other
hazardous material.
LOWER OR SUPPORT RAISED EQUIPMENT
Do not work under raised 3 point lift arms without supporting them. Do not
use support material made of concrete blocks, logs, buckets, barrels, or any
other material that could suddenly collapse or shift positions. Make sure
support material is solid, not decayed, warped, twisted, or tapered. Lower lift
arms to ground level or onto blocks. Lower lift arms and attachments to the
ground before leaving the cab or operator’s station.
USE CARE WITH HYDRAULIC FLUID PRESSURE
Hydraulic fluid pressure can penetrate the skin and cause serious injury or
death. Hydraulic leaks under pressure may not be visible. Before connecting
or disconnecting hydraulic hoses, read your prime movers operator’s manual
for detailed instructions on connecting and disconnecting hydraulic hoses or
fittings.
• Keep unprotected body parts, such as face, eyes, and arms as far away
as possible from a suspected leak. Flesh injected with hydraulic fluid
may develop gangrene or other permanent disabilities.
• If injured by injected fluid, see a doctor at once. If your doctor is not
familiar with this type of injury, ask him to research immediately to
determine proper treatment.
• Wear safety glasses, protective clothing, and use a sound piece of card
board or wood when searching for hydraulic leaks. DO NOT USE YOUR
HANDS! SEE ILLUSTRATION BELOW.
DO NOT MODIFY MACHINE OR ATTACHMENTS
Modifications may weaken the integrity of the attachment and may impair the
function, safety, life, and performance of the attachment. When making
repairs, use only the manufacturer’s genuine parts, following authorized
instructions. Other parts may be substandard in fit and quality. Never modify
any ROPS (Roll Over Protection System) equipment or device. Any
modifications must be authorized in writing by the manufacturer.
MODEL PS5 & PS6
HARLEY POWER SEEDER®
WARNING
WARNING
SAFELY OPERATE EQUIPMENT
Do not operate equipment until you are completely trained by a qualified
operator in how to use the controls, know its capabilities, dimensions, and all
safety requirements. See your prime movers manual for these instructions.
• Keep all step plates, grab bars, pedals, and controls free of dirt, grease,
debris, and oil.
• Never allow anyone to be around the equipment when it is operating or
being serviced.
• Do not allow riders on the attachment or the prime mover.
• Do not operate the equipment from anywhere other than the correct
operators position.
• Never leave equipment unattended with the engine running or with this
attachment in a raised position.
• Do not alter or remove any safety feature from the prime mover or this
attachment.
• Know your work site safety rules as well as traffic rules and flow.
When in doubt on any safety issue, contact your supervisor or safety
coordinator for an explanation.
SAFELY MAINTAIN AND REPAIR EQUIPMENT
• Do not wear loose clothing or any accessories that can catch in moving
parts. If you have long hair, cover or secure it so that it does not be come
entangled in the equipment.
• Work on a level surface in a well lit area.
• Use properly grounded electrical outlets and tools.
• Use the correct tool for the job at hand. Make sure they are in good
condition for the task required.
• Wear the protective equipment specified by the tool manufacturer.
EQUIPMENT SAFETY PRECAUTIONS
NOTICE
Safety is a primary concern in the design and manufacture of our products.
Unfortunately, our efforts to provide safe equipment can be wiped out by a
single careless act of an operator. In addition, to the design and configuration
of equipment, hazard control and accident prevention are dependent upon
the awareness, concern, prudence, and proper training of personnel involved
in the operation, transport, maintenance, and storage of equipment. The
designed and tested safety of this equipment depends on it being operated
within the limitations as explained in this manual.
INITIAL SET-UP AND SYSTEMS CHECK
• Always check with your prime mover manual or dealer for counter weight
ballast that may be required for machine stability.
• Air in hydraulic systems can cause erratic operation and allows loads or
equipment components to drop unexpectedly.
• Before operating equipment purge any air in the system by engaging all
hydraulic functions.
• Check that all control lever positions function as instructed in the
Operator’s Manual. Do not operate until control lever and equipment
MODEL PS5 & PS6
HARLEY POWER SEEDER® WARNING
•
•
•
•
•
•
WARNING
movements are correct.
Make sure all hydraulic hoses, fittings and valves are in good
condition and not leaking before starting power unit. Check and route
hoses carefully to prevent damage.
Hoses must not be twisted, bent sharply, kinked, frayed, pinched, or
come into contact with any moving parts.
Operate moveable components through full operational range to check
clearances. Replace damaged hoses immediately.
Ensure implement is properly attached, adjusted and in good condition.
Tractor must be equipped with ROPS and seat belt/operator restraint.
Keep seat belt/operator restraint securely fastened/engaged. Falling off
tractor can result in death from being run over or crushed. Keep ROPS
systems in place at all times.
SAFELY OPERATE EQUIPMENT
• Improper operation can cause the machine to tip or roll over and cause
injury or death.
• Keep tractor lift arms and attachment as low as possible.
• Turn on level ground.
• Go up and down slopes, not across them.
• Keep the heavy end of the machine uphill.
• Only engage power when equipment is at ground level. Always
disengage power when equipment is raised off the ground.
• Do not disconnect hydraulic lines until all system pressure is relieved.
• Never go underneath equipment lowered to the ground or raised.
Hydraulic system leak down, hydraulic system failures, mechanical
failures or movement of control levers can cause equipment to drop or
rotate unexpectedly and cause severe injury or death.
• Never direct discharge toward people, animals or property.
• Do not operate equipment while under the influence of alcohol or drugs.
• Operate only in the daylight or good artificial lighting.
• Always comply with all state and local lighting and marking requirements.
• Ensure equipment is properly attached, adjusted and in good operating
condition.
• Before starting tractor, check all equipment driveline guards for damage
and make sure they rotate freely on all drivelines. Replace any damaged
guards. If guards do not rotate freely on drivelines, repair and replace
bearings before operating.
• Make sure driveline is correct length to prevent bottoming out or pulling
apart during the full lift range of the hitch.
• Make sure spring-activated locking pin or collar slides freely and is
seated firmly in tractor PTO splined groove.
• A minimum 20% of tractor and equipment weight must be on tractor front
wheels with attachments in “transport” position. Without this weight,
tractor could tip over causing personal injury or death. The weight may
be attained with a loader, front wheel weights, ballast in tires, or front
tractor weights. When attaining wheels, you must not exceed the Roll
Over Protection Structure (ROPS) weight certification. Weigh the tractor
and equipment. Do not estimate.
MODEL PS5 & PS6
HARLEY POWER SEEDER®
• Ensure shields and guards are properly installed and in good condition.
Replace if damaged.
WARNING WATCH FOR OPERATING HAZARDS
• Look down and to the rear and make sure area is clear before operating in
•
•
•
•
•
•
reverse.
Watch for hidden hazards on the terrain during operation.
Use extreme care when working close to fences, ditches, other
obstructions, or on hillsides.
Reduce ground speed on slopes and rough terrain.
Do not operate on steep slopes.
Do not stop, start, or change directions suddenly on slopes.
Stop tractor and implement immediately upon striking an obstruction.
Dismount tractor using proper procedure. Inspect and repair any damage
before resuming operation.
WARNING MAINTENANCE SAFETY
• Your dealer can supply original equipment hydraulic accessories
and repair parts. Substitute parts may not meet original equipment
specifications and may be dangerous.
• Avoid electrical system hazards. Never work on the electrical system
unless you are qualified and thoroughly familiar with system details and
the special handling requirements.
• Disconnect battery before working on electrical system. Remove “ground”
cable first. When reconnecting battery, connect “ground” cable last.
• Never perform service or maintenance with engine running.
• Tighten all bolts, nuts and screws, and check that all cotter pins are
installed securely to ensure equipment is in a safe condition before
operating.
MODEL PS5 & PS6
HARLEY POWER SEEDER®
SAFETY DECAL AND SERIAL TAG PLACEMENT
4
1
4
2
7
6
5
3
Figure 1. Safety Decals
10 MODEL PS5 & PS6
HARLEY POWER SEEDER®
SAFETY DECALS
#1 - PN: P978250
#3 - SERIAL TAG
#2 - PN: P970100
#6 - PN: P970300
#5 - PN: P975106
#7 - PN: 50-0769
#4 - PN: P976400 (Red)
MODEL PS5 & PS6
HARLEY POWER SEEDER®
11
OPERATIONAL PROCEDURE
NOTICE
The Harley Power Seeder is designed for applying seed directly onto
conditioned soil, in conjunction with the Harley Power Rake®. This manual
contains information for the PS5 & PS6 model. Refer to the information in this
manual for specifications, parts, assemblies and adjustments.
The Harley Power Seeder used with the Harley Power Rake®, allows the operator to
pulverize and condition the seedbed, while at the same time, drop a metered amount of seed
onto a prepared bed and gently compress the seed into the seedbed.
When operating the Power Rake with Seeder attached, the rake should not be angled. The end
plates should be mounted in working position.
Use the top three point adjustment link to control roller depth, which will also determine pressure
on the packer drum, which firms the seedbed.
NOTICE
Follow the Operational Procedures outlined in the Power Rake Operator’s
Manual for proper operation.
POWER RAKE PRE-INSTALLATION
. The seeder is mounted to the back of the frame where the gauge wheels normally are.
Remove the gauge wheel assemblies from the rake. Attach the lift arms to the frame to
dimensions shown (See Figure 6). Install caster fork assembly into detachable caster
arms (See Figure 7).
2. Replace the barrier adjustment bar with curved bar.
ATTACHING SEEDER TO HARLEY POWER RAKE®
Move tractor and rake into position in front of the seeder. Move back slowly and carefully, not
allowing anyone to be between the rake and the seeder until receivers are in position to lift seeder.
Carefully raise rake until hooks on seeder are fully engaged. Turn off tractor engine.
Install the 3/4” pins to secure the seeder.
Raise jackstand and secure in operating position.
POWER RAKE ROLLER RPM
The RPM of the Power Rake roller will determine the flow of soil over the roller and how far it
pitches the soil toward the packer drum. As the seed is dropped into this soil flow, the amount of
exposed seed percentage is determined by location of soil flow over the roller in relation to seed
drop zone. To get more seed exposed, slow the RPM of the roller to allow seed to be dropped.
Start with tractor tachometer at 1500 rpm and work up to find optimal seed to soil contact.
BERM LEVELERS
Excessive material may pass over the ends of the roller, creating a ridge which will leave an
uneven seedbed. Lower the berm levelers to spread this material out.
12 MODEL PS5 & PS6
HARLEY POWER SEEDER®
OPERATIONAL PROCEDURE
Figure 2. Berm Adjustments
MODEL PS5 & PS6
HARLEY POWER SEEDER®
13
OPERATIONAL PROCEDURE
SEED RATE ADJUSTMENT
When properly adjusted, the holes in the slide should line up with the holes in the box, with
the control handle set at “6”. To make an adjustment, loosen the control handle on the box,
move the slide until the holes line up. When the handle is moved to “0” the holes in the box
should be completely covered. If the holes are not covered, loosen the three bolts holding the
seedmeter casting and shift it slightly so that the “0” mark is farther from the control handle.
Retighten the bolts. Move control handle to “0”. Holes in the box should then be completely
covered.
NOTICE
When changing seed rate always move control handle to “0” then to
new value.
Figure 3. Seed Rate Adjustment
14 MODEL PS5 & PS6
HARLEY POWER SEEDER®
OPERATIONAL PROCEDURE
To double the seed rate in this chart, the pulleys must be reversed.
. Remove the belt.
2. Remove the hex bolt securing each pulley and remove pulleys.
3. Reassemble with the 5-1/2” pulley on the packer drum. Note, 5-1/2” pulley must also be
flipped (hub side out) and the 4” pulley flipped (hub side in) to maintain belt alignment.
Figure 4. Seed Rate
MODEL PS5 & PS6
HARLEY POWER SEEDER®
15
OPERATIONAL PROCEDURE
Shutting Down
Stop equipment.
Lower the lift arms and power rake to the ground.
Purge any air in the system. Hydraulic system leakdown, hydraulic system failures, mechanical
failures, or movement of control levers can cause equipment to drop or rotate unexpectedly.
Shut off engine, set brake, remove key, and remove seat belt before leaving the tractor operator’s
seat.
Do not disconnect hydraulic lines until all system pressure is relieved. Lower unit to ground, stop engine, and operate all hydraulic control levers.
REMOVING SEEDER FROM POWER RAKE
Lower jack stands to “storage” position.
Remove the seeder attachment pins.
On a hard level surface, lower seeder to the ground.
Carefully drive away from seeder, watching that the lift hooks have cleared the attachment
arms.
STORAGE
Make sure the disconnected seeder is stored on a hard, level surface.
Block equipment securely for storage.
Keep children and bystanders away from storage area.
MAINTENANCE
•
•
•
•
Grease packer drum bearings 1-2 pumps with #2 lithium with moly weekly.
Check belt for signs of wear or misalignment monthly.
Clean out seed box after each job.
Inspect and clean safety decals.
CHANGING AGITATOR BLADES
Agitator blades are supplied as standard on your seed box. They should operate leaving a
slight clearance with the bottom of the seed box.
16 MODEL PS5 & PS6
HARLEY POWER SEEDER®
MAINTENANCE
NOTICE
Before proceeding with any agitator installation, be sure to note the
direction of shaft rotation on your seeder.
Figure 5. Agitator Blades
. Remove drive pulley.
2. Remove two capscrews (inside the box) which hold end bearing on right end of right
seed box.
3. Slide shaft out of right end.
4. Agitators should be installed with careful attention to the direction of shaft rotation as
seed rate will be reduced if they run “backwards”.
MODEL PS5 & PS6
HARLEY POWER SEEDER®
17
ASSEMBLY - RAKE & SEEDER
Figure 7. Rake & Seeder Assembly
18 MODEL PS5 & PS6
HARLEY POWER SEEDER®
9.66
42.94
ASSEMBLY - SEEDER/CASTER BRACKET 5’
Figure 6. Caster Placement 5’
MODEL PS5 & PS6
HARLEY POWER SEEDER®
19
6
33
8
8
6
40
A
13
13
1
20
35
16
17
32
14
36
15
31
24
13
28
STAND IN THE
DOWN POSITION
15
REPLACED
COTTER PIN
1
10
30
46
22
17
16
14
32
36
24
15
15
9
43
35
2
REPLACES SQ.
BUSHING IN
SEED BOX
STAND IN THE
UP POSITION
38
39
19
41
4
21
13
5 1/2" PULLEY
ON TOP
A
40
11
3
27
6
18
6
33
8
42
8
44
23
42
26
18
7
6
7
37
8
9
5
22
15
33
29
34
9
45
14
25
12
HARLEY POWER SEEDER®
20 MODEL PS5 & PS6
Diagram 1 of 2
ASSEMBLY - seeder 5’
ASSEMBLY - seeder 5’
ITEM
Part
Qty
DESCRIPTION
1.
2.
3.
4.
5.
07-0204
2
07-0205
2
07-06861
07-12791
07-17141
Pin, Roll, Gr2, 1/4 x 2
Pin, Cotter, Gr2, 1/8 x 1
Washer, Machined, 1 3/4-1 1/8
Screw, Set, Gr5, 3/8-16 x 3/4
Screw, HHC, Gr8, 5/16-18 x 1
6.
7.
8.
9.
10.
07-1718
9
07-1810
3
07-2116
9
07-2300
4
07-28431
Washer, Lock, Split, Medium, 3/8
Nut, Hex, Lock, Gr8, 5/16-18
Screw, HHC, Gr8, 3/8-16 x 1 1/4
Washer, Flat, CL8.8, M16
Pin, Klik, 3/16 x 1 1/4
11.
12.
13.
14.
15.
07-32721
07-34321
07-365914
07-4038
9
07-537014
Nut, Hex, Jam, Gr8, 3/8-16
Screw, HHC, Gr8, 1/4-20 x 3/4
Screw, HHC, Gr8, 3/8-16 x 2 3/4
Washer, Lock, Split, Medium, 1/4
Nut, Hex, Lock, Gr8, 3/8-16
16.
07-7358
8
17.
07-7407
2
18.13-1430
2
19.
M100181
20.
M100191
Screw, HHC, Gr8, 1/4-20 x 1/2
Cap, Tube, Round, 1.0
Key, 1/4 x 1 1/4
Weld, Panel, Side, Left
Weld, Panel, Side, Right
21.
22.
23.
24.
25.
M100231
M10033
2
M100361
M10037
2
M100391
Shaft, Extension
Bearing, Spacer
Tension, Arm
Assembly, Comb, Lift
Weld, Shield, Side
26.
27.
28.
29.
30.
M100401
M100411
M100611
M100641
M10070
1
Pulley, 4 Inch, with Hub
Pulley, 5.5 Inch, with Hub
Weld, Main Frame
Weld, Packer, Drum
Weld, Seed, Baffle
31.
32.
33.
34.
35.
M10081
2
M10082
2
M5009-2
3
M54441
M6448
2
Weld, Bracket, Lift
Weld, Stand, Seeder
Washer, 1/8 x 1 3/4 x 13/32
Roller, Tension
Weld, Handle
MODEL PS5 & PS6
List 1 of 2
HARLEY POWER SEEDER®
21
6
33
8
8
6
40
A
13
13
1
20
35
16
17
32
15
14
36
31
24
13
28
STAND IN THE
DOWN POSITION
15
REPLACED
COTTER PIN
1
10
30
46
22
17
16
14
32
36
24
15
15
9
43
35
2
REPLACES SQ.
BUSHING IN
SEED BOX
STAND IN THE
UP POSITION
38
39
19
41
4
21
13
5 1/2" PULLEY
ON TOP
A
40
11
3
27
6
18
33
6
8
42
8
44
26
18
7
23
42
6
7
37
8
9
5
22
15
33
29
34
9
45
14
25
12
HARLEY POWER SEEDER®
22 MODEL PS5 & PS6
Diagram 2 of 2
ASSEMBLY - seeder 5’
Figure 8. Seeder Assembly 5’
ASSEMBLY - seeder 5’
ITEM
QTY
List 2 of 2
PART NO.DESCRIPTION
36.
37.
38.
39.
40.
M6556
2
M66301
M8263
2
P0066001
P007900
2
Assembly, Barrie Pin
Bushing, Pivot
Weld, Jack, Pin, 5/8 x 3 5/8
Bearing, Insert
Flange, Bearing, 1 1/8
41.
42.
43.
44.
45.
46.
P0300361
P110512
2
P604500
2
P6048001
P9522241
P9600011
V-Belt, B-36
Screw, Socket Head, Gr8, 5/16-18 x 3
Spring, Compression, 3 Inch
Spring, Extension
Snap Ring, Heavy, 5/8
Box, Seeder, Brillion, 5Ft
MODEL PS5 & PS6
HARLEY POWER SEEDER®
23
ASSEMBLY - seeder box 5’
27
15
13
15
15
3
2
1
9
11
24
8
23
16
17
5
19
10
5
9
7
8
20
12
6
4
22
14
25
28
18
22
11
13
21
19
11
22
13
26
CORRECT AGITATOR
ORIENTATION
25
29
22
22
20
Figure 9. Seeder Box 5’
24 MODEL PS5 & PS6
HARLEY POWER SEEDER®
ASSEMBLY - seeder box 5’ PARTS LIST
ITEM
part
qty
DESCRIPTION
1.
2.
3.
4.
5.
07-0006
4
07-0140
4
07-0141
4
07-01561
07-1309
2
Screw, Phillips, Gr2, 10-24 x 1
Washer, Lock, Gr2, 10
Nut, Hex, Gr2, 10-24
Washer, Flat, Gr8, 1/2
Screw, HHC, Gr8, 1/2-13 x 1 1/4
6.
7.
8.
9.
10.
07-15051
07-17141
07-1762
2
07-1764
2
07-32461
Screw, Set, Gr2, 1/4-20 x 3/4
Screw, HHC, Gr8, 5/16-18 x 1
Washer, Lock, Split, Medium, 1/2
Nut, Hex, Gr8, 1/2-13
Nut, Wing, 3/8-16
11.
12.
13.
14.
15.
07-3273
8
07-32791
07-3436
8
07-36701
07-6634
3
Washer, Lock, Split, Medium, 5/16
Washer, Flat, Gr8, 3/8
Screw, HHC, Gr8, 5/16-18 x 3/4
Screw, HHC, Gr8, 1/2-13 x 1
Washer, Flat, Gr8, 7/8
16.
17.
18.
19.
20.
07-74241
07-74251
07-7429
2
07-7430
2
07-7431
2
Plate, Shifter, Right
Handle, Shifter
Latch, Rubber
Bushing, Square Hole
Bearing, Housing, End
21.
22.
23.
24.
25.
07-74321
07-7433
5
07-74341
07-7435
2
07-7441
2
Bearing, Hosing, Intermediate
Washer, .0747 x 2.75, with Square Hole
Bolt, Square Head, 3/8-16 x 1
Cover, Lock Assembly
Blade, Agitator
26.
27.
28.
29.
07-74421
07-74431
07-74441
P0066001
Shaft, Square, 5 Ft
Cover, 5 Ft
Hopper, Seedbox, 5 Ft
Bearing, Insert, 1 Inch
MODEL PS5 & PS6
HARLEY POWER SEEDER®
25
notes
26 MODEL PS5 & PS6
HARLEY POWER SEEDER®
ASSEMBLY - SEEDER/CASTER BRACKET 6’
Figure 10. Caster Placement 6’
MODEL PS5 & PS6
HARLEY POWER SEEDER®
27
6
8
32
8
A
6
13
40
13
1
31
17
34
14
16
26
21
30
15
36
STAND IN THE
DOWN POSITION
13
REPLACED
COTTER PIN
15
19
10
46
24
1
23
31
17
36
16
14
26
15
15
9
34
43
2
REPLACES SQ.
BUSHING IN
SEED BOX
STAND IN THE
UP POSITION
38
13
39
20
22
41
A
40
11
18
13
4
5 1/2" PULLEY
ON TOP
6
3
8
29 32 6
42
18
44
7
7
28
25
42
15
6
9
5
24
32
37
8
35
33
9
8
45
14
27
12
HARLEY POWER SEEDER®
28 MODEL PS5 & PS6
Diagram 1 of 2
ASSEMBLY - seeder 6’
Figure 11. Seeder Assembly 6’
ASSEMBLY - seeder 6’
ITEM
part
qty
DESCRIPTION
1.
2.
3.
4.
5.
07-0204
2
07-0205
2
07-06861
07-12791
07-17141
Pin, Roll, Gr2, 1/4 x 2
Pin, Cotter, Gr2, 1/8 x 1
Washer, Machined, 1 3/4-1 1/8
Screw, Set, Gr5, 3/8-16 x 3/4
Screw, HHC, Gr8, 5/16-18 x 1
6.
7.
8.
9.
10.
07-1718
9
07-1810
3
07-2116
9
07-2300
4
07-28431
Washer, Lock, Split, Medium, 3/8
Nut, Hex, Lock, Gr8, 5/16-18
Screw, HHC, Gr8, 3/8-16 x 1 1/4
Washer, Flat, CL8.8, M16
Pin, Klik, 3/16 x 1 1/4
11.
12.
13.
14.
15.
07-32721
07-34321
07-365914
07-4038
9
07-537014
Nut, Hex, Jam, Gr8, 3/8-16
Screw, HHC, Gr8, 1/4-20 x 3/4
Screw, HHC, Gr8, 3/8-16 x 2 3/4
Washer, Lock, Split, Medium, 1/4
Nut, Hex, Lock, Gr8, 3/8-16
16.
07-7358
8
17.
07-7407
2
18.13-1430
2
19.
M100011
20.
M100181
Screw, HHC, Gr8, 1/4-20 x 1/2
Cap, Tube, Round, 1.0
Key, 1/4 x 1 1/4
Weld, Frame, Main, Seeder, 6Ft
Weld, Panel, Side, Left
21.
22.
23.
24.
25.
M100191
M100231
M10030
1
M10033
2
M100361
Weld, Panel, Side, Right
Shaft, Extension
Weld, Baffle, Seed
Bearing, Spacer
Tension, Arm
26.
27.
28.
29.
30.
M10037
2
M100391
M100401
M100411
M10081
2
Assembly, Comb, Lift
Weld, Shield, Side
Pulley, 4 Inch, with Hub
Pulley, 5.5 Inch, with Hub
Weld, Bracket, Lift
31.
32.
33.
34.
35.
M10082
2
M5009-2
3
M54441
M6448
2
M64791
Weld, Stand, Seeder
Washer, 1/8 x 1 3/4 x 13/32
Roller, Tension
Weld, Handle
Weld, Packer Drum
MODEL PS5 & PS6
List 1 of 2
HARLEY POWER SEEDER®
29
6
8
32
8
A
6
13
40
13
1
31
17
34
14
16
26
21
30
15
36
STAND IN THE
DOWN POSITION
13
REPLACED
COTTER PIN
15
19
10
46
24
1
23
31
17
36
16
14
26
15
15
9
34
43
2
REPLACES SQ.
BUSHING IN
SEED BOX
STAND IN THE
UP POSITION
38
13
39
20
22
41
A
40
11
18
13
4
5 1/2" PULLEY
ON TOP
6
3
8
29 32 6
42
18
44
7
7
28
25
42
15
6
9
5
24
32
37
8
35
33
9
8
45
14
27
12
HARLEY POWER SEEDER®
30 MODEL PS5 & PS6
Diagram 2 of 2
ASSEMBLY - seeder 6’
Figure 11. Seeder Assembly
ASSEMBLY - seeder 6’
ITEM
part
qty
List 2 of 2
DESCRIPTION
36.
37.
38.
39.
40.
M6556
2
M66301
M8263
2
P0066001
P007900
2
Assembly, Barrie Pin
Bushing, Pivot
Weld, Jack, Pin, 5/8 x 3 5/8
Bearing, Insert
Flange, Bearing, 1 1/8
41.
42.
43
44.
45.
46.
P0300361
P110512
2
P604500
2
P6048001
P9522241
P9600001
V-Belt, B-36
Screw, Socket Head, Gr8, 5/16-18 x 3
Spring, Compression, 3 Inch
Spring, Extension
Snap Ring, Heavy, 5/8
Box, Seeder, Brillion
MODEL PS5 & PS6
HARLEY POWER SEEDER®
31
ASSEMBLY - seeder box 6’
1
2
3
15
15
29
15
24
25
9
19
8 28
18
5
12
10
17
27
5
6
13
11
4
14
22
7
16
23
27
11
13
26
24
27
21
22
27
11
13
26
24
11
27
22
CORRECT AGITATOR
ORIENTATION
20
13
25
27
27
30
Figure 12. Seeder Box 6’
32 MODEL PS5 & PS6
HARLEY POWER SEEDER®
ITEM
part
ASSEMBLY - seeder box 6’ PARTS LIST
qty
DESCRIPTION
1.
2.
3.
4.
5.
07-0006
4
07-0140
4
07-0141
4
07-01561
07-1309
2
Screw, Phillips, Gr2, 10-24 x 1
Washer, Lock, Gr2, 10
Nut, Hex, Gr2, 10-24
Washer, Flat, Gr8, 1/2
Screw, HHC, Gr8, 1/2-13 x 1 1/4
6.
7.
8.
9.
10.
07-15051
07-17141
07-1762
2
07-1764
2
07-32461
Screw, Set, Gr2, 1/4-20 x 3/4
Screw, HHC, Gr8, 5/16-18 x 1
Washer, Lock, Split, Medium, 1/2
Nut, Hex, Gr8, 1/2-13
Nut, Wing, 3/8-16
11.
12.
13.
14.
15.
07-327311
07-32791
07-343611
07-36701
07-6634
3
Washer, Lock, Split, Medium, 5/16
Washer, Flat, Gr8, 3/8
Screw, HHC, Gr8, 5/16-18 x 3/4
Screw, HHC, Gr8, 1/2-13 x 1
Washer, Flat, Gr8, 7/8
16.
17.
18.
19.
20.
07-74221
07-74231
07-74241
07-74251
07-74261
Hopper, Seedbox, 6 Ft
Cover, 6 Ft
Plate, Shifter, Right
Handle, Shifter
Shaft, Square
21.
22.
23.
24.
25.
07-74271
07-7428
3
07-7429
2
07-7430
3
07-7431
2
Spacer, Blade
Blade, Agitator, 22.5 Inches
Latch, Rubber
Bushing, Square Hole
Bearing, Housing, End
26.
27.
28.
29.
30.
07-7432
2
07-7433
7
07-74341
07-7435
2
P0066001
Bearing, Hosing, Intermediate
Washer, .0747 x 2.75, with Square Hole
Bolt, Square Head, 3/8-16 x 1
Cover, Lock Assembly
Bearing, Insert, 1 Inch
MODEL PS5 & PS6
HARLEY POWER SEEDER®
33
ASSEMBLY - OPTIONAL 3PT HITCH
10
8
1
9
2
6
10
6
10
2
4
4
5
5
3
9
2
9
3
8
10
7
1
1
7
4
5
4
3
8
5
3
Figure 13. 3PT Hitch Assembly
ITEM
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
part
qty
07-0205
2
07-2300
2
07-3656
2
07-5370
2
M10046
2
M100471
M100891
M100561
M8263
2
P604500
2
P955801
2
34 MODEL PS5 & PS6
DESCRIPTION
Pin, Cotter, Gr2, 1/8 x 1
Washer, Flat, CL8.8, M16
Screw, HHC, Gr8, 3/8-16 x 1 3/4
Nut, Hex, Lock, 3/8-16, Gr8
Weld, Stand, Clamp
Weld, Tractor 3 Point Mount
Assembly, Tine Bar, 5FT
Assembly, Tine Bar, 6FT
Weld, Jack Pin, 5/8 x 3 5/8
Spring, Compression, 3 Inch
Plug, Tube, 1 1/2
HARLEY POWER SEEDER®
ASSEMBLY - optional tine bar
3
1
4
5
2
Figure 14. Tine Bar Assembly
M10089 5 FT
ITEM
1.
2.
3.
4.
5.
part
qty
M100901
07-365714
07-537014
P70410014
07-327514
DESCRIPTION
Tine Tube, Horizontal
Screw, HHC, Gr8, 3/8-16 x 2
Nut, Hex, Lock, St, Gr8, 3/8-16
Tine Coil, .31 x 9.4
Washer, Flat, Gr8, 5/16
M10056 6 FT
ITEM
1.
2.
3.
4.
5.
part
qty
M100551
07-365718
07-537018
P70410018
07-327518
MODEL PS5 & PS6
DESCRIPTION
Tine Tube, Horizontal
Screw, HHC, Gr8, 3/8-16 x 2
Nut, Hex, Lock, St, Gr8, 3/8-16
Tine Coil, .31 x 9.4
Washer, Flat, Gr8, 5/16
HARLEY POWER SEEDER®
35
ASSEMBLY - OPTIONAL bracket kit
2
1
1
2
3
Figure 15. Bracket Kit 5 Ft
ITEM
1.
2.
3.
part
qty
M10011
2
M10022
2
M100731
DESCRIPTION
Weld, Caster, Support, Arm
Assembly, Lock, Arm
Manual, Adjustment Bar
3
2
2
3
4
4
1
Figure 16. Bracket Kit 6 Ft
ITEM
1.
2.
3.
4.
part
qty
M100091
M10011
2
M10022
2
P955850
2
36 MODEL PS5 & PS6
DESCRIPTION
Weld, Barrier, Adjustment Arm
Weld, Caster, Support, Arm
Assembly, Lock, Arm
Cap, Square, 1/2 x 3
HARLEY POWER SEEDER®
WARRANTY POLICY
Harley Attachments, LLC warrants its line of Harley equipment to be free from defects in material and
factory workmanship for a period of twelve (12) months. Exception to this warranty period will be Harley
Rock Pickers, which will carry a six (6) month warranty.
Warranty registration form must be filled out, signed by the customer, and returned to Harley
Attachments, LLC within thirty (30) days from the date of purchase before any warranty claim will be
considered. Dealer rental units are considered sold units and the same warranty policy applies.
This warranty is limited exclusively to equipment manufactured by Harley Attachments, LLC and is
subject to inspection by Harley Attachments, LLC to identify the nature and cause of failure. This company
in no way warrants belts, bearings, hydraulics, chains, sprockets, tires, or any other trade accessory not
manufactured by Harley Attachments, LLC since these items are warranted separately by their respective
manufactures.
This warranty shall become void if, in the best judgement of Harley Attachments, LLC, the equipment
has been subject to misuse, negligence, alterations, and damage by accident or lack of required
maintenance or if the product has been used for a purpose for which it was not intended. Wear items such
as, but not limited to, rollers and drive chains will not be covered under warranty. Normal wear
depreciation is not covered by warranty. Claims for equipment damaged in transit should be referred to
the freight carrier. Harley Attachments, LLC will not be responsible for damages incurred in transit.
Harley Attachments, LLC obligations under this warranty shall be limited to repair or replacement at its
option of the equipment or trade accessories as they conform to this policy. Trade accessories such as
but not limited to bearings, tires and wheels, etc will be sent to the respective manufacturer for warranty
consideration. Any warranty reimbursement as related to these items will rely solely on the decision of
each separate manufacture including Harley Attachments, LLC. Reimbursement on parts will be at dealer
net and labor allowances are calculated according to Harley Attachments, LLC’s predetermined flat time
and rate. Freight charges and misc. shop supplies are not covered under warranty.
Dealer’s responsibility is to fully explain the warranty policy to the customer before starting any repairs.
Return the defective parts (prepaid) along with a completed Harley Attachments, LLC warranty form. All
replacement parts used in warranty must be furnished by Harley Attachments, LLC (please refer to
warranty procedures). The selling dealer has no authority to make any representation or promise on behalf
of Harley Attachments, LLC or to modify the terms or conditions of this warranty in any way.
Owner’s responsibility is to complete and return the warranty registration within thirty (30) days from the
date of purchase. Operate and maintain the equipment according to the recommendations in the owner’s
manual. The owner is responsible for freight and transportation to and from the dealership or any service
calls made by the dealer.
This warranty is subject to any conditions of supply, which may directly affect our ability to obtain materials
or manufacture replacement parts.
Harley Attachments, LLC reserves the right to make improvements in design or change in specifications
of its products without notice and is not obligated to make the same improvements to equipment
previously manufactured.
THERE IS NO OTHER EXPRESSED OR IMPLIED WARRANTY ON THIS PRODUCT OR ON ITS
MERCHANTABILITY OR ON ITS FITNESS. TO THE EXTENT ALLOWED BY LAW NEITHER HARLEY
ATTACHMENTS, LLC NOR THE SELLING HARLEY DEALER SHALL HAVE ANY RESPONSIBILITY
FOR LOSS OF USE OF THE PRODUCT, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS,
OR CONSEQUENTIAL DAMAGES.
MODEL PS5 & PS6
HARLEY POWER SEEDER®
37
Harley Attachments, LLC
1805 2nd Avenue SW
Jamestown, ND 58401
800-437-9779 Phone
701-252-1978 Fax
701-952-9307 Parts Fax
Email: [email protected]
Web: www.paladinbrands.com