Asus M2NC61S Personal Computer User manual

Add to my manuals

advertisement

Asus M2NC61S Personal Computer User manual | Manualzz

U2811

V-Series M2NC61S

ASUS PC (Desktop Barebone)

Installation Manual

2

Refer to the system user guide for installation details and other system information from ASUS website.

Front panel features

5 . 2 5 - i n c h d r i v e bay cover

This V-series provide V2/V3 two types of front panel for users to choose, please refer to your product package for the front panel type you purchased.

Rear panel features

Power connector

Voltage selector

PS/2 mouse port

PS/2 keyboard port

SPDIF Out

Parallel port

USB 2.0 ports

Center/subwoofer port

Microphone port

Line Out port

Line In port

Expansion slot

Metal brackets

3 . 5 - i n c h d r i v e b a y cover

Headphone port

Microphone port

USB 2.0 ports

HDD LED

Reset button

Power button

Power supply fan

Cover screw

Chassis fan vents

VGA port

IEEE 1394 port

Side speak out port

LAN (RJ-45) port

Rear speak out port

Cover screw

Metal bracket lock

Installation manual

Internal components

5

9

10

11

6

7

2

3

4

1

12

1. Front panel cover

2. 5.25-inch optical drive bays

3. Hard disk drive bay

4. Floppy disk drive bay

5. Power supply unit

6. CPU socket

7. DIMM sockets

Selecting the voltage

The system’s power supply unit has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate system input voltage according to the voltage supply in your area.

If the voltage supply in your area is

100-127 V, set the switch to 115 V.

If the voltage supply in your area is

200-240 V, set the switch to 230 V.

8. ASUS motherboard

9. PCI Express x16 slot

10. PCI Express x1 slot

11. PCI slots

12. Metal bracket lock

Installation manual 3

Removing the side cover and front panel assembly

1. Remove the cover screws on the rear panel.

2. Pull the side cover toward the rear panel until its hooks disengage from the chassis tabs. Set the side cover aside.

3. Locate the front panel assembly hooks, then lift them until they disengage from the chassis.

4. Swing the front panel assembly to the right, until the hinge-like tabs on the right side of the assembly are exposed.

5. Remove the front panel assembly, then set aside.

3

Air duct 1

4

2

3

1

4

2 3

Chassis tab holes

4

Installing a CPU

To install a CPU:

1. Locate the CPU socket,then lift the socket lever to a 90º-

100º angel.

4 Installation manual

2. Install the CPU to the socket, making sure that the CPU cornes with the gold triangle matches the socket corner with a small triangle.

3. Push down he socket lever to secure the CPU.

Installing the CPU fan and heatsink assembly

1. Place the heatsink on top of the installed CPU, making sure that the heatsink fits properly on the retention module base.

2. Attach one end of the retention bracket to the retention module base.

3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place.

4. Push down the retention bracket lock on the retention mechanism to secure the heatsink and fan to the module base.

5. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN.

1

CPU Fan

CPU Heatsink

Retention bracket

Retention bracket lock

Retention

Module Base

3 4

5

2

Installation manual 5

6

Installing a DIMM

1. Locate the DIMM sockets in the motherboard.

2. Unlock a DIMM socket by pressing the retaining clips outward.

3. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket.

4. Push the DIMM to the socket until the retaining clips snap inward.

• Unplug the power supply before adding or removing DIMMs.

Failure to do so may cause damage to the motherboard and/or components.

• A DDR2 DIMM is keyed with a notch so that it fits in only one direction. Do not force a DIMM into a socket to avoid damaging the

DIMM.

Installing an expansion card

1. Remove the metal bracket lock.

2. Remove the metal cover opposite the slot that you intend to use.

2

1

3. Insert the card connector to the slot, then press the card firmly until it fits in place.

4. Replace the metal bracket lock.

3

4

Installation manual

Installing storage drives

Optical drive

1. Place the chassis upright, then remove the upper 5.25” drive bay metal plate cover.

2. Insert the optical drive to the bay, then carefully push the drive until its screw holes align with the holes on the bay.

3. Secure the optical drive with two screws on both sides of the bay.

4. Connect the IDE (A) and power

(B) plugs to connectors at the back of the drive.

Floppy disk drive

1. Place the chassis upright, then remove the lower 3.5” drive bay metal plate cover.

2. Insert the floppy disk drive to the bay, then carefully push the drive until its screw holes align with the holes on the bay.

3. Secure the floppy disk drive with two screws on both sides of the bay.

4. Connect the signal (A) and power (B) plugs to connectors at the back of the drive.

Hard disk drive

1. Place the chassis upright, then remove the upper 3.5” drive bay metal plate cover.

2. Insert the hard disk drive to the bay, then carefully push the drive until its screw holes align with the holes on the bay.

3. Secure the hard disk drive with two screws on both sides of the bay.

3

Installation manual

3

3

A

A

2

3

B

2

3

3

2

B

7

8

4. For SATA HDD: Connect the

SATA signal and power plugs to the connectors at the back of the drive.

For IDE HDD: Connect the IDE signal and power plugs to the connectors at the back of the drive.

SATA IDE

Removing the bay covers and reinstalling the front panel assembly and side cover

If you installed an optical and/or floppy disk drive, remove the bay cover(s) on the front panel assembly before reinstalling it to the chassis. To do this:

1. Locate the bay cover locks.

2. Press the locks outward to release the bay cover.

3. Push the bay cover inward, then set it aside.

4. Follow the same instructions to remove the 3.5” drive bay cover.

To reinstall the front panel assembly and side cover:

1. Insert the front panel assembly hinge-like tabs to the holes on the right side of the chassis.

2. Swing the front panel assembly to the left, then insert the hooks to the chassis until the front panel assembly fits in place.

3. Insert the side cover hooks to the chassis top and bottom holes.

4. Push the side cover to the direction of the front panel until it fits in place.

5. Secure the cover with two screws you removed earlier.

2

1

5

Air duct

4

2 1

5

1

2

3

2

Chassis tab holes

Installation manual

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement