INSTALLATION AND INSTRUCTION MANUAL

9016LED

Plus

™

Minibar

NOTICE

Due to continuous product improvements, we must reserve the right to change any specifications and information, contained in this manual at any time without notice. Star Headlight & Lantern Co., Inc. makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Star Headlight & Lantern Co., Inc. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual.

LED FIVE YEAR LIMITED WARRANTY

The manufacturer warrants this LED light against factory defects in material and workmanship for five years after the date of purchase. The owner will be responsible for returning to the Service Center any defective item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or replace at its

option, products, or part(s), which its inspection determines to be defective. Repaired or replacement item(s) will be returned to the purchaser with transportation costs prepaid from the service point. A copy of the purchaser's receipt must be returned with the defective item(s) in order to qualify for the warranty coverage. Exclusions from this warranty include, but are not limited to, domes, and/or the finish. This warranty shall not apply to any light, which has been altered, such that in the manufacturer's judgment, the performance or reliability has been affected, or if any damage has resulted from abnormal use or service.

There are no warranties expressed or implied (including any warranty of merchantability or fitness), which extend this warranty period. The loss of use of the product, loss of time, inconvenience, commercial loss or

consequential damages, including costs of any labor, are not covered. The manufacturer reserves the right to change the design of the product without assuming any obligation to modify any product previously manufactured.

This warranty gives you specific legal rights. You might also have additional rights that may vary from state to state. Some states do not allow limitations on how long an implied warranty lasts. Some states do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above limitation(s) or exclusion(s) may not apply to you.

If you have any questions concerning this or any other product, please contact our Customer Service Department at (585) 226-9787.

If a product must be returned for any reason, please contact our Customer Service Department to obtain a Returned Material Authorization number (RMA #) before you ship the product back.

Please write the RMA # clearly on the package near the mailing label.

PLIT419 REV. D 10/19/12

IMPORTANT: Please read all of the following instructions before installing your new warning light.

Permanent Mounting

1. Using the gasket as a template, mark the four bolt holes on the mounting surface (and the center wire hole, if you will be needing one).

2. Drill a 9/32" hole in the four marked spots or the mounting bolts.

CAUTION: Take care not to drill

through the headliner below.

3. Insert the head of two mounting bolts into each of the access holes found along the slots on the bottom of the bar and slide one to each end of the base.

Slide the heads of two mounting

bolts into each bolt access hole

along each of the two

mounting slots.

4. Route the wires through the center of the gasket and align the bolts properly BEFORE

REMOVING THE BACKING.

5. Remove the adhesive backing on the gasket and carefully stick the gasket onto the

base, over the bolts, with the wires routed through the center hole.

6. Route your wires through the mounting surface if applicable.

7. Install your light with the four bolts going through your mounting holes. Place a washer and nut on each of the bolts and tighten until snug.

-1-

Wiring for Permanent Mount Models

CAUTION: All of our DC powered warning lights are polarity sensitive. These lights are polarity protected only if the appropriate fuse is used. All wires connected to the positive terminal of the battery should be fused at the battery for their rated load. Testing the

light before this fuse is properly installed will void the warranty on the light.

Red - (Power) Connect to +12-24 VDC through your switch. Be sure to use a 10

amp fuse when connecting the switch to the positive side of the power supply.

Black - (Ground) Connect to the negative side of the battery.

Purple - (Optional - High/Low) Switches the light between High and Low power.

• High Power Only: Leave disconnected (cover wire with wire nut or tape)

• Low Power Only: Connect to Ground

• High/Low Switching Option: Connect to Ground through a switch

Red w/Green - (Pattern Select) Touch and release to +12-24 VDC to change patterns (see

next page).

White - (Synchronization) If you are only installing one unit, cut the White wire short and tape the end.

Connect the white wires from both units together ONLY AFTER

PROGRAMMING them for the same pattern.

Synchronization of Multiple Lights

You can synchronize up to six lights with compatibility.

DO NOT CONNECT WHITE WIRES UNTIL PROGRAMMING HAS BEEN COMPLETED

FOR ALL LIGHTS!!

1. Power up the first unit and select a pattern.

2. Program the second light with the same Pattern.

•

The two lights will flash together (simultaneous).

•

Optionally you can program one light for Pattern 16 and the other for Pattern 17. This will cause the lights to flash opposite one another (alternate).

3. After programming all lights, tie off the green wires and connect the white wires together.

4. Test lights by applying power to all of them at the same time.

Magnet Mounting

If you are mounting the light on the roof of your vehicle, take extreme care to ensure that the magnet is firmly seated on your roof, and that the pull of the magnet is sufficient to secure the light in place. Since the composition of the metal in the roofs of different vehicles may vary, as well as the contour, texture, and/or condition, Star cannot guarantee the ability of the light to remain in place on a moving vehicle. It is the sole responsibility of the owner to ensure the warning light is secure.

Care should be taken when routing the cig plug cord so that it does not interfere with the proper operation of the driver-side or passenger-side airbag! Failure to heed this warning may result in serious or fatal injury.

-2-

Pattern Programming

• To change patterns, press and release the Pattern Select Button

(cig plug models only) or briefly touch and release the Red w/Green

Stripe wire to +12-24VDC (hard-wired versions only).

• The cycle repeats after the last pattern.

• Pattern Shortcuts: Touch and hold the Red w/Green Stripe Wire to +12/24VDC (or hold the Pattern Select Button) for the length of time that corresponds to the pattern you would like to jump to.

Length of Hold Unit Blinks Shortcut to

3 seconds

6 seconds

1 time

2 times

Pattern 1

Pattern 6

9 seconds

12 seconds

3 times

4 times

Pattern 11

Pattern 16

Once you find the pattern you wish to display, connect the Pattern Select wire to ground

(hard-wire only) and deactivate the light. This will store the selected pattern.

Flash

Pattern

#

Pattern

Type

1 K

Patterns for ALL Colors

Except For Amber

Alternating Flicker †

2

3

4

5

8

9

6

7

10

11

12

13

14

15

16

17

18

19

L

M

N

O

F

G

H

I

J

P

Q

R

S

T

G

G

U

V

Alternating Fast Doubleflash

Alternating Tripleflash

Patterns for Amber Lights

Alternating Flicker †

Alternating Fast Doubleflash

Alternating Tripleflash

Alternating PSU Flicker

Alternating PSU Random

Alternating PSU Flicker

Alternating PSU Random

Alternating Quadflash ††

Alternating Quadflash w/Post-Pop

Alternating Singleflash

Alternating Doubleflash

Alternating Quadflash ††

Alternating Quadflash w/Post-Pop

Alternating Singleflash

Alternating Doubleflash

Alternating Variable

Alternating Quintflash †††

Swing

Alt. Fast Doubleflash, Alt. Flicker

Alt. Quad, Alt. Flicker, Alt. Double, Flicker

Counter Clockwise Rotating Flash

Sim. Quad w/Post Pop (Phase 1) ††††

Sim. Quad w/Post Pop (Phase 2)

Alt. Triple, Alt. Non-Synch Double, Alt. Quint,

Flicker

Alternating Variable

Alternating Post Pop

Alternating Random

Alternating Quintflash

Alt. Fast Doubleflash, Alt. Flicker

Alt. Quad, Alt. Flicker, Alt. Double, Flicker

Sim. Quad w/Post Pop (Phase 1) ††††

Sim. Quad w/Post Pop (Phase 2)

Alt. Triple, Alt. Non-Synch Double, Alt. Quint,

Flicker

Steady burn one side, Other side Single Flash Steady burn one side, Other side Single Flash

NONE 20 Cycle All Cycle All

† = Programming Shortcuts 1, 2, 3, and 4 (see table above)

Please Note: These instructions are provided as a general guideline only. Specific mounting, wiring, and/or weather-sealing may be necessary and are the sole responsibility of the installer. Star Headlight & Lantern Co., Inc. assumes no responsibility for the integrity of the installation for this or any of its products.

-3-