KINO-ABT-i2 Series MODEL:
KINO-ABT-i2 Mini-ITX SBC
MODEL:
KINO-ABT-i2 Series
Mini-ITX SBC with 22nm Intel® Atom™ or Celeron® SoC,
Dual GbE, DDR3, HDMI, VGA, DisplayPort, USB 3.0,
COM, SATA 3Gb/s, IPMI 2.0 and RoHS
User Manual
Page i
Rev. 1.00 – August 28, 2014
KINO-ABT-i2 Mini-ITX SBC
Revision
Date
Version
Changes
August 28, 2014
1.00
Initial release
Page ii
KINO-ABT-i2 Mini-ITX SBC
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page iii
KINO-ABT-i2 Mini-ITX SBC
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 INTRODUCTION........................................................................................................... 2
1.2 MODEL VARIATIONS ................................................................................................... 3
1.3 BENEFITS ................................................................................................................... 4
1.4 FEATURES ................................................................................................................... 4
1.5 CONNECTORS ............................................................................................................. 5
1.6 DIMENSIONS ............................................................................................................... 6
1.7 DATA FLOW ................................................................................................................ 7
1.8 TECHNICAL SPECIFICATIONS ...................................................................................... 8
2 PACKING LIST ............................................................................................................11
2.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 12
2.2 UNPACKING PRECAUTIONS ....................................................................................... 12
2.3 PACKING LIST........................................................................................................... 13
2.4 OPTIONAL ITEMS ...................................................................................................... 14
3 CONNECTORS ........................................................................................................... 16
3.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 17
3.1.1 KINO-ABT-i2 Layout ....................................................................................... 17
3.1.2 Peripheral Interface Connectors ..................................................................... 18
3.1.3 External Interface Panel Connectors............................................................... 19
3.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 19
3.2.1 ATX Power Connector ..................................................................................... 19
3.2.2 Audio Connector .............................................................................................. 20
3.2.3 Battery Connector............................................................................................ 21
3.2.4 Chassis Intrusion Connector............................................................................ 22
3.2.5 Digital I/O Connector ...................................................................................... 23
3.2.6 DisplayPort Connector .................................................................................... 24
3.2.7 EC Debug Connector....................................................................................... 25
3.2.8 Fan Connector (CPU)...................................................................................... 26
3.2.9 Fan Connector (System) .................................................................................. 27
Page iv
KINO-ABT-i2 Mini-ITX SBC
3.2.10 Front Panel Connector .................................................................................. 28
3.2.11 iRIS Module Slot............................................................................................. 29
3.2.12 Keyboard and Mouse Connector ................................................................... 30
3.2.13 LAN LED Connectors .................................................................................... 31
3.2.14 Memory Card Slots ........................................................................................ 32
3.2.15 PCIe x4 Slot ................................................................................................... 33
3.2.16 PCIe Mini Card Slot ...................................................................................... 33
3.2.17 Power Button ................................................................................................. 35
3.2.18 Reset Button Connector ................................................................................. 36
3.2.19 SATA 3Gb/s Drive Connectors....................................................................... 36
3.2.20 SATA Power Connectors ................................................................................ 37
3.2.21 Serial Port Connectors, RS-232..................................................................... 38
3.2.22 Serial Port Connector, RS-422/485................................................................ 39
3.2.23 SMBus Connector .......................................................................................... 40
3.2.24 SPDIF Connector........................................................................................... 41
3.2.25 SPI Flash Connector...................................................................................... 42
3.2.26 SPI Flash Connector, EC ............................................................................... 43
3.2.27 TPM Connector.............................................................................................. 44
3.2.28 USB 2.0 Connectors....................................................................................... 45
3.3 EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL ......................................... 47
3.3.1 Audio Connector .............................................................................................. 47
3.3.2 Ethernet and USB 2.0 Combo Connector ........................................................ 48
3.3.3 Ethernet and USB 3.0 Combo Connector ........................................................ 49
3.3.4 HDMI Connector ............................................................................................. 50
3.3.5 Serial Port Connectors (COM1 and COM2) ................................................... 51
3.3.6 VGA Connector ................................................................................................ 52
4 INSTALLATION ......................................................................................................... 54
4.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 55
4.2 INSTALLATION CONSIDERATIONS .............................................................................. 55
4.2.1 SO-DIMM Installation ..................................................................................... 57
4.2.2 iRIS-2400 Module Installation......................................................................... 57
4.2.3 PCIe Mini Card Installation ............................................................................ 59
4.3 SYSTEM CONFIGURATION ......................................................................................... 60
4.3.1 AT/ATX Power Mode Setting ........................................................................... 60
Page v
KINO-ABT-i2 Mini-ITX SBC
4.3.2 Clear CMOS Button......................................................................................... 61
4.3.3 Flash Descriptor Security Override................................................................. 61
4.3.4 mSATA/SATA Selection..................................................................................... 62
4.3.5 USB Power Select ............................................................................................ 62
4.4 INTERNAL PERIPHERAL DEVICE CONNECTIONS ........................................................ 63
4.4.1 SATA Drive Connection ................................................................................... 63
4.4.2 USB Cable Connection .................................................................................... 64
4.5 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 65
4.5.1 Audio Connector .............................................................................................. 65
4.5.2 HDMI Display Device Connection .................................................................. 66
4.5.3 LAN Connection............................................................................................... 67
4.5.4 USB Connection............................................................................................... 67
4.5.5 Serial Device Connection ................................................................................ 68
4.5.6 VGA Monitor Connection ................................................................................ 69
4.6 IPMI SETUP PROCEDURE ......................................................................................... 70
4.6.1 Managed System Hardware Setup ................................................................... 70
4.6.2 Using the IEI iMAN Web GUI.......................................................................... 71
5 BIOS .............................................................................................................................. 73
5.1 INTRODUCTION......................................................................................................... 74
5.1.1 Starting Setup................................................................................................... 74
5.1.2 Using Setup ...................................................................................................... 74
5.1.3 Getting Help..................................................................................................... 75
5.1.4 Unable to Reboot after Configuration Changes .............................................. 75
5.1.5 BIOS Menu Bar................................................................................................ 75
5.2 MAIN........................................................................................................................ 76
5.3 ADVANCED ............................................................................................................... 78
5.3.1 ACPI Settings ................................................................................................... 78
5.3.2 Super IO Configuration ................................................................................... 80
5.3.2.1 Serial Port n Configuration ....................................................................... 80
5.3.3 iWDD Hardware Monitor ................................................................................ 88
5.3.3.1 Smart Fan Function................................................................................... 90
5.3.4 RTC Wake Settings ........................................................................................... 92
5.3.5 Serial Port Console Redirection ...................................................................... 93
5.3.6 CPU Configuration .......................................................................................... 96
Page vi
KINO-ABT-i2 Mini-ITX SBC
5.3.7 IDE Configuration ........................................................................................... 98
5.3.8 Trusted Computing ......................................................................................... 100
5.3.9 USB Configuration......................................................................................... 101
5.4 CHIPSET ................................................................................................................. 102
5.4.1 North Bridge .................................................................................................. 103
5.4.1.1 Intel IGD Configuration.......................................................................... 103
5.4.2 South Bridge................................................................................................... 105
5.4.2.1 Azalia HD Audio..................................................................................... 107
5.4.2.2 PCI Express Configuration ..................................................................... 108
5.5 SECURITY ............................................................................................................... 109
5.6 BOOT.......................................................................................................................110
5.7 EXIT ........................................................................................................................112
6 SOFTWARE DRIVERS .............................................................................................114
6.1 AVAILABLE SOFTWARE DRIVERS .............................................................................115
6.2 SOFTWARE INSTALLATION .......................................................................................115
6.3 CHIPSET DRIVER INSTALLATION ..............................................................................117
6.4 GRAPHICS DRIVER INSTALLATION .......................................................................... 120
6.5 LAN DRIVER INSTALLATION .................................................................................. 123
A BIOS OPTIONS ........................................................................................................ 128
B TERMINOLOGY...................................................................................................... 131
C WATCHDOG TIMER .............................................................................................. 135
D HAZARDOUS MATERIALS DISCLOSURE ....................................................... 138
D.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 139
Page vii
KINO-ABT-i2 Mini-ITX SBC
List of Figures
Figure 1-1: KINO-ABT-i2 ................................................................................................................2
Figure 1-2: Connectors ..................................................................................................................5
Figure 1-3: KINO-ABT-i2 Main Dimensions (mm)........................................................................6
Figure 1-4: Data Flow Diagram......................................................................................................7
Figure 3-1: Connectors and Jumpers (Front Side) ...................................................................17
Figure 3-2: ATX Power Connector Location ..............................................................................20
Figure 3-3: Audio Connector Location .......................................................................................21
Figure 3-4: Battery Connector Location.....................................................................................22
Figure 3-5: Chassis Intrusion Connector Location...................................................................23
Figure 3-6: Digital I/O Connector Location ................................................................................24
Figure 3-7: DisplayPort Connector Location .............................................................................25
Figure 3-8: EC Debug Connector Location................................................................................26
Figure 3-9: CPU Fan Connector Location ..................................................................................27
Figure 3-10: System Fan Connector Location...........................................................................28
Figure 3-11: Front Panel Connector Location ...........................................................................29
Figure 3-12: iRIS Module Slot Location......................................................................................30
Figure 3-13: Keyboard and Mouse Connector Location...........................................................31
Figure 3-14: LAN LED Connector Locations .............................................................................32
Figure 3-15: Memory Card Slot Locations .................................................................................33
Figure 3-16: PCIe x4 Slot Location .............................................................................................33
Figure 3-17: PCIe Mini Card Slot Location .................................................................................34
Figure 3-18: Power Button Location...........................................................................................35
Figure 3-19: Reset Button Connector Location.........................................................................36
Figure 3-20: SATA 3Gb/s Drive Connector Locations ..............................................................37
Figure 3-21: SATA Power Connector Locations .......................................................................38
Figure 3-22: RS-232 Serial Port Connector Locations..............................................................39
Figure 3-23: RS-422/485 Connector Location............................................................................40
Figure 3-24: SMBus Connector Location ...................................................................................41
Figure 3-25: SPDIF Connector Location ....................................................................................42
Figure 3-26: SPI Flash Connector Location...............................................................................43
Page viii
KINO-ABT-i2 Mini-ITX SBC
Figure 3-27: SPI EC Flash Connector Location.........................................................................44
Figure 3-28: TPM Connector Location........................................................................................45
Figure 3-29: USB 2.0 Connector Locations ...............................................................................46
Figure 3-30: External Peripheral Interface Connector ..............................................................47
Figure 3-31: Audio Connector .....................................................................................................48
Figure 3-32: Ethernet Connector.................................................................................................48
Figure 3-33: Ethernet Connector.................................................................................................50
Figure 3-34: HDMI Connector ......................................................................................................51
Figure 3-35: Serial Port Pinouts ..................................................................................................52
Figure 3-36: VGA Connector .......................................................................................................53
Figure 4-1: SO-DIMM Installation ................................................................................................57
Figure 4-2: iRIS Module Installation............................................................................................58
Figure 4-3: PCIe Mini Card Retention Screw Removal .............................................................59
Figure 4-4: PCIe Mini Card Installation (Full-size).....................................................................60
Figure 4-5: AT/ATX Power Mode Switch Location ....................................................................60
Figure 4-6: Clear CMOS Button Location...................................................................................61
Figure 4-7: Flash Descriptor Security Override Jumper Location ..........................................61
Figure 4-8: mSATA/SATA Switch Location................................................................................62
Figure 4-9: SATA Drive Cable Connection.................................................................................63
Figure 4-10: Dual USB Cable Connection ..................................................................................64
Figure 4-11: Audio Connector .....................................................................................................65
Figure 4-12: HDMI Connection ....................................................................................................66
Figure 4-13: LAN Connection ......................................................................................................67
Figure 4-14: USB Connector........................................................................................................68
Figure 4-15: Serial Device Connector.........................................................................................69
Figure 4-16: VGA Connector .......................................................................................................70
Figure 4-17: IEI iMAN Web Address............................................................................................71
Figure 4-18: IEI iMAN Web GUI....................................................................................................72
Figure 6-1: Driver CD Main Menu ............................................................................................. 116
Figure 6-2: Available Drivers .................................................................................................... 116
Figure 6-3: Chipset Driver Welcome Screen........................................................................... 117
Figure 6-4: Chipset Driver License Agreement ...................................................................... 118
Figure 6-5: Chipset Driver Read Me File ................................................................................. 118
Figure 6-6: Chipset Driver Setup Operations ......................................................................... 119
Figure 6-7: Chipset Driver Installation Finish Screen............................................................ 119
Page ix
KINO-ABT-i2 Mini-ITX SBC
Figure 6-8: Graphics Driver Welcome Screen ........................................................................ 121
Figure 6-9: Graphics Driver License Agreement.................................................................... 121
Figure 6-10: Graphics Driver Read Me File ............................................................................. 122
Figure 6-11: Graphics Driver Setup Operations ..................................................................... 122
Figure 6-12: Graphics Driver Installation Finish Screen ....................................................... 123
Figure 6-13: PC Properties ....................................................................................................... 124
Figure 6-14: System Control Panel .......................................................................................... 124
Figure 6-15: Device Manager List ............................................................................................ 125
Figure 6-16: Update Driver Software Window ........................................................................ 126
Figure 6-17: Locate Driver Files ............................................................................................... 126
Page x
KINO-ABT-i2 Mini-ITX SBC
List of Tables
Table 1-1: Model Variations ...........................................................................................................3
Table 1-2: KINO-ABT-i2 Specifications.......................................................................................10
Table 2-1: Packing List.................................................................................................................14
Table 2-2: Optional Items.............................................................................................................15
Table 3-1: Peripheral Interface Connectors ...............................................................................19
Table 3-2: Rear Panel Connectors ..............................................................................................19
Table 3-3: ATX Power Connector Pinouts .................................................................................20
Table 3-4: Audio Connector Pinouts ..........................................................................................21
Table 3-5: Battery Connector Pinouts ........................................................................................22
Table 3-6: Chassis Intrusion Connector Pinouts ......................................................................23
Table 3-7: Digital I/O Connector Pinouts....................................................................................24
Table 3-8: DisplayPort Connector Pinouts ................................................................................25
Table 3-9: EC Debug Connector Pinouts ...................................................................................26
Table 3-10: CPU Fan Connector Pinouts ...................................................................................27
Table 3-11: System Fan Connector Pinouts ..............................................................................28
Table 3-12: Front Panel Connector Pinouts...............................................................................29
Table 3-13: Keyboard and Mouse Connector Pinouts ..............................................................31
Table 3-14: LAN1 LED Connector Pinouts.................................................................................32
Table 3-15: LAN2 LED Connector Pinouts.................................................................................32
Table 3-16: PCIe Mini Card Slot Pinouts ....................................................................................35
Table 3-17: Reset Button Connector Pinouts ............................................................................36
Table 3-18: SATA 3Gb/s Drive Connector Pinouts....................................................................37
Table 3-19: SATA Power Connector Pinouts.............................................................................38
Table 3-20: RS-232 Serial Port Connector Pinouts ...................................................................39
Table 3-21: RS-422/485 Connector Pinouts ...............................................................................40
Table 3-22: RS-422/485 Pinouts of D-sub 9 Connector.............................................................40
Table 3-23: SMBus Connector Pinouts ......................................................................................41
Table 3-24: SPDIF Connector Pinouts ........................................................................................42
Table 3-25: SPI Flash Connector Pinouts ..................................................................................43
Table 3-26: SPI EC Flash Connector Pinouts ............................................................................44
Page xi
KINO-ABT-i2 Mini-ITX SBC
Table 3-27: TPM Connector Pinouts ...........................................................................................45
Table 3-28: USB1 Pinouts ............................................................................................................46
Table 3-29: USB2 Pinouts ............................................................................................................46
Table 3-30: LAN2 Ethernet Connector Pinouts .........................................................................48
Table 3-31: Connector LEDs........................................................................................................49
Table 3-32: USB 2.0 Port Pinouts................................................................................................49
Table 3-33: LAN1 Ethernet Connector Pinouts .........................................................................49
Table 3-34: Connector LEDs........................................................................................................50
Table 3-35: USB 3.0 Port Pinouts................................................................................................50
Table 3-36: HDMI Connector Pinouts .........................................................................................51
Table 3-37: Serial Port Pinouts....................................................................................................52
Table 3-38: VGA Connector Pinouts...........................................................................................52
Table 4-1: Flash Descriptor Security Override Jumper Settings.............................................61
Table 4-2: mSATA/SATA Switch Settings ..................................................................................62
Table 4-3: BIOS Options and Configured USB Ports................................................................62
Table 5-1: BIOS Navigation Keys ................................................................................................75
Table 5-2: BIOS Options and Configured USB Ports............................................................. 106
Page xii
KINO-ABT-i2 Mini-ITX SBC
BIOS Menus
BIOS Menu 1: Main .......................................................................................................................76
BIOS Menu 2: Advanced ..............................................................................................................78
BIOS Menu 3: ACPI Configuration ..............................................................................................79
BIOS Menu 4: Super IO Configuration........................................................................................80
BIOS Menu 5: Serial Port n Configuration Menu.......................................................................80
BIOS Menu 6: iWDD Hardware Monitor ......................................................................................89
BIOS Menu 7: Smart Fan Function .............................................................................................90
BIOS Menu 10: RTC Wake Settings ............................................................................................92
BIOS Menu 11: Serial Port Console Redirection .......................................................................94
BIOS Menu 12: CPU Configuration .............................................................................................96
BIOS Menu 13: IDE Configuration...............................................................................................98
BIOS Menu 14: Trusted Computing ......................................................................................... 100
BIOS Menu 14: USB Configuration .......................................................................................... 101
BIOS Menu 15: Chipset ............................................................................................................. 102
BIOS Menu 16: North Bridge .................................................................................................... 103
BIOS Menu 17: Intel IGD Configuration................................................................................... 103
BIOS Menu 18: South Bridge.................................................................................................... 105
BIOS Menu 20: Azalia HD Audio .............................................................................................. 107
BIOS Menu 19: PCI Express Configuration ............................................................................ 108
BIOS Menu 20: Security ............................................................................................................ 109
BIOS Menu 21: Boot .................................................................................................................. 110
BIOS Menu 22:Exit..................................................................................................................... 112
Page xiii
KINO-ABT-i2 Mini-ITX SBC
Chapter
1
1 Introduction
Page 1
KINO-ABT-i2 Mini-ITX SBC
1.1 Introduction
Figure 1-1: KINO-ABT-i2
The KINO-ABT-i2 is a Mini-ITX form factor single bard computer. It has an on-board 22nm
Intel® Atom™ or Celeron® processor, and supports two 204-pin 1333/1066 MHz
dual-channel unbuffered DDR3 Low Voltage (DDR3L) SDRAM SO-DIMM with up to
8.0 GB of memory.
The KINO-ABT-i2 features Intelligent Platform Management Interface (IPMI) that helps
lower the overall costs of server management by enabling users to maximize IT resource,
save time and manage multiple systems. The KINO-ABT-i2 supports IPMI 2.0 through the
optional iRIS-2400 module.
The KINO-ABT-i2 includes one VGA port and one HDMI port for dual independent display.
It also has an internal DisplayPort (iDP) connector supporting HDMI, LVDS, VGA, DVI and
DisplayPort displays with up to 3840 x 2160 resolutions. Expansion and I/O include one
PCIe x4 slot (with PCIe x1 signal), one PCIe Mini slot, two USB 3.0 ports plus two USB 2.0
on the rear panel, four USB 2.0 by pin header, two SATA 3Gb/s connectors, five RS-232
serial ports, and one RS-422/485 connector.
Page 2
KINO-ABT-i2 Mini-ITX SBC
1.2 Model Variations
There are eight models of the KINO-ABT-i2 series. The model variations are listed in
Table 1-1.
Model
On-board SoC
Max. Memory Size
Intel® Celeron® processor J1900
8 GB
Standard
KINO-ABT-i2-J19001
(2 GHz, quad-core, 2 MB cache)
KINO-ABT-i2-N29301
Intel® Celeron® processor N2930
8 GB
(1.83 GHz, quad-core, 2 MB cache)
KINO-ABT-i2-N28071
Intel® Celeron® processor N2807
4 GB
(1.58 GHz, dual-core, 2 MB cache)
By Request
KINO-ABT-i2-E38451
Intel® Atom™ processor E3845
8 GB
(1.91 GHz, quad-core, 2 MB cache)
KINO-ABT-i2-E38271
Intel® Atom™ processor E3827
8 GB
(1.75 GHz, dual-core, 1 MB cache)
KINO-ABT-i2-E38261
Intel® Atom™ processor E3826
8 GB
(1.46 GHz, dual-core, 1 MB cache)
KINO-ABT-i2-E38251
Intel® Atom™ processor E3825
4 GB
(1.33 GHz, dual-core, 1 MB cache)
KINO-ABT-i2-E38151
Intel® Atom™ processor E3815
4 GB
(1.46 GHz, single-core, 512 KB cache)
Table 1-1: Model Variations
Page 3
KINO-ABT-i2 Mini-ITX SBC
1.3 Benefits
Some of the KINO-ABT-i2 motherboard benefits include:

Powerful graphics with multiple monitors

Staying connected with both wired LAN connections

Speedy running of multiple programs and applications
1.4 Features
Some of the KINO-ABT-i2 motherboard features are listed below:

Mini-ITX form factor

RoHS compliant

On-board 22nm Intel® Atom™ or Celeron® processor

Two 204-pin 1333/1066 MHz dual-channel unbuffered DDR3L (1.35 V)
SDRAM SO-DIMM slots support up to 8.0 GB of memory
Page 4

iDP, VGA and HDMI interfaces for dual independent display

Supports IPMI 2.0 via IEI iRIS-2400 module

Two Intel® PCIe GbE connectors

Two SATA 3Gb/s connectors

One PCIe Mini card expansion slot

One PCIe x4 (x1 mode) expansion slot

Two USB 3.0 ports and six USB 2.0 ports

Five RS-232 serial ports and one RS-422/485 serial port

High Definition Audio
KINO-ABT-i2 Mini-ITX SBC
1.5 Connectors
The connectors on the KINO-ABT-i2 are shown in the figure below.
Figure 1-2: Connectors
Page 5
KINO-ABT-i2 Mini-ITX SBC
1.6 Dimensions
The main dimensions of the KINO-ABT-i2 are shown in the diagram below.
Figure 1-3: KINO-ABT-i2 Main Dimensions (mm)
Page 6
KINO-ABT-i2 Mini-ITX SBC
1.7 Data Flow
Figure 1-4 shows the data flow between the system chipset, the CPU and other
5
components installed on the motherboard.
Figure 1-4: Data Flow Diagram
Page 7
KINO-ABT-i2 Mini-ITX SBC
1.8 Technical Specifications
KINO-ABT-i2 technical specifications are listed below.
Specification/Model
KINO-ABT-i2
Form Factor
Mini-ITX
On-board SoC

Standard
o
Intel® Celeron® processor J1900
(2GHz, quad-core, 2MB cache, TDP=10W)
o
Intel® Celeron® processor N2930
(1.83GHz, quad-core, 2MB cache, TDP=7.5W)
o
Intel® Celeron® processor N2807
(1.58GHz, dual-core, 2MB cache, TDP=4.5W)

By request
o
Intel® Atom™ processor E3845
(1.91GHz, quad-core, 2MB cache, TDP=10W)
o
Intel® Atom™ processor E3827
(1.75GHz, dual-core, 1MB cache, TDP=8W)
o
Intel® Atom™ processor E3826
(1.46GHz, dual-core, 1MB cache, TDP=7W)
o
Intel® Atom™ processor E3825
(1.33GHz, dual-core, 1MB cache, TDP=6W)
o
Intel® Atom™ processor E3815
(1.46GHz, single-core, 512KB cache, TDP=5W)
Integrated Graphics
Intel® HD Graphics Gen7 with 4 execution units, supporting DirectX
11.1, OpenCL 1.2 and OpenGL 4.2
Memory
Two 204-pin 1066/1333MHz dual-channel DDR3L (1.35 V) SDRAM
SO-DIMMs support up to 8 GB (J1900, N2930, E3845, E3827,
E3826) or 4 GB (N2807, E3825, E3815)
Audio
Realtek ALC662 HD Audio codec
BIOS
UEFI BIOS
Page 8
KINO-ABT-i2 Mini-ITX SBC
Specification/Model
KINO-ABT-i2
Ethernet Controllers
LAN1: Intel® I210-AT PCIe Ethernet controller with NCSI and
IPMI 2.0 support
LAN2: Intel® I211-AT PCIe Ethernet controller
Digital I/O
8-bit digital I/O (4-bit input, 4-bit output)
IPMI 2.0
Supported by the optional iRIS-2400 module
Super I/O Controller
Fintek F81866D-I
Embedded Controller
ITE IT8528E
Watchdog Timer
Software programmable supports 1 sec–255 sec system reset
Expansion
PCIe
One PCIe x4 (x1 mode) slot
PCIe Mini
One PCIe Mini card slot supports mSATA, co-lay SATA 2
I/O Interface Connectors
Audio Connector
One internal audio connector (10-pin)
Display Ports
One VGA port (up to 2560 x 1600, 60Hz)
One HDMI port (up to 2560 x 1600, 60Hz)
One internal DisplayPort supports HDMI, LVDS, VGA, DVI, DP (up to
3840 x 2160, 60Hz)
Ethernet
Two RJ-45 GbE ports
Keyboard/Mouse
One internal keyboard/mouse connector
Serial Ports
One RS-422/485 via internal wafer connector
Three RS-232 via internal pin headers
Two RS-232 via D-sub 9 connector
USB ports
Two external USB 3.0 ports
Two external USB 2.0 ports
Four USB 2.0 ports by two 8-pin headers
Serial ATA
Two SATA 3Gb/s connectors with two 5 V SATA power connectors
LAN LED
Two 2-pin LAN active LED connectors
SMBus
Supported by one 4-pin wafer connector
Page 9
KINO-ABT-i2 Mini-ITX SBC
Specification/Model
KINO-ABT-i2
Environmental and Power Specifications
Power Supply
ATX power supported
Power Consumption
5 V @ 1.71 A, 12 V @ 0.08 A, Vcore_12 V @ 0.27 A, 3.3 V @ 0.34 A
(Intel® Celeron® processor J1900 with two 4 GB 1333 MHz DDR3
memory)
Operating Temperature
-20ºC–60ºC
Storage Temperature
-30ºC–70ºC
Humidity
5%–95% (non-condensing)
Physical Specifications
Dimensions
170 mm x 170 mm
Weight GW/NW
900 g / 450 g
Table 1-2: KINO-ABT-i2 Specifications
Page 10
KINO-ABT-i2 Mini-ITX SBC
Chapter
2
2 Packing List
Page 11
KINO-ABT-i2 Mini-ITX SBC
2.1 Anti-static Precautions
WARNING!
Static electricity can destroy certain electronics. Make sure to follow the
ESD precautions to prevent damage to the product, and injury to the
user.
Make sure to adhere to the following guidelines:

Wear an anti-static wristband: Wearing an anti-static wristband can prevent
electrostatic discharge.

Self-grounding: Touch a grounded conductor every few minutes to discharge
any excess static buildup.

Use an anti-static pad: When configuring any circuit board, place it on an
anti-static mat.

Only handle the edges of the PCB: Don't touch the surface of the
motherboard. Hold the motherboard by the edges when handling.
2.2 Unpacking Precautions
When the KINO-ABT-i2 is unpacked, please do the following:
Page 12

Follow the antistatic guidelines above.

Make sure the packing box is facing upwards when opening.

Make sure all the packing list items are present.
KINO-ABT-i2 Mini-ITX SBC
2.3 Packing List
NOTE:
If any of the components listed in the checklist below are missing, do
not proceed with the installation. Contact the IEI reseller or vendor the
KINO-ABT-i2
was
purchased
from
or
contact
an
IEI
sales
representative directly by sending an email to [email protected]
3
The KINO-ABT-i2 is shipped with the following components:
Quantity
Item and Part Number
1
KINO-ABT-i2 single board computer
1
SATA and power cable
Image
(P/N: 32801-000201-300-RS)
1
Dual-port USB cable
(P/N: CB-USB02A-RS)
1
I/O shielding
(P/N: 45014-0038C0-01-RS)
1
Utility CD
Page 13
KINO-ABT-i2 Mini-ITX SBC
Quantity
Item and Part Number
1
Quick Installation Guide
Image
Table 2-1: Packing List
2.4 Optional Items
The following are optional components which may be separately purchased:
Item and Part Number
IPMI 2.0 adapter card with AST2400 BMC chip
(P/N: iRIS-2400-R10)
Dual USB cable
(P/N: 32000-070301-RS)
Keyboard and mouse Y cable
(P/N: 32006-000300-100-RS)
RS-232 cable
(P/N : 32200-000049-RS)
RS-422/485 cable, 200mm
(P/N: 32205-003800-300-RS)
DisplayPort to DisplayPort converter board for iEi IDP
connector
(P/N: DP-DP-R10)
Page 14
Image
KINO-ABT-i2 Mini-ITX SBC
Item and Part Number
Image
DisplayPort to DVI-D converter board for iEi IDP connector
(P/N: DP-DVI-R10)
DisplayPort to HDMI converter board for IEI IDP connector
(P/N: DP-HDMI-R10)
DisplayPort to 24-bit dual-channel LVDS converter board
for iEi IDP connector
(P/N: DP-LVDS-R10)
DisplayPort to VGA converter board for IEI IDP connector
(P/N: DP-VGA-R10)
Infineon TPM module, v3.17 firmware
(P/N: TPM-IN01-R11)
Table 2-2: Optional Items
Page 15
KINO-ABT-i2 Mini-ITX SBC
Chapter
3
3 Connectors
Page 16
KINO-ABT-i2 Mini-ITX SBC
3.1 Peripheral Interface Connectors
This chapter details all the jumpers and connectors.
3.1.1 KINO-ABT-i2 Layout
The figures below show all the connectors and jumpers.
Figure 3-1: Connectors and Jumpers (Front Side)
Page 17
KINO-ABT-i2 Mini-ITX SBC
3.1.2 Peripheral Interface Connectors
The table below lists all the connectors on the board.
Connector
Type
Label
ATX power input connector
24-pin connector
ATX1
Audio connector
10-pin header
FRONT-PANEL1
Battery connector
2-pin wafer
BAT1
Chassis intrusion connector
2-pin header
CHASSIS1
Digital I/O connector
10-pin header
DIO1
DisplayPort connector
20-pin box header
DP1
EC debug connector
18-pin header
CN9
Fan connector (CPU)
4-pin wafer
CPU_FAN1
Fan connector (system)
4-pin wafer
SYS_FAN1
Front panel connector
14-pin header
F_PANEL1
iRIS module connector
204-pin SO-DIMM slot
IPMI1
Keyboard and mouse connector
6-pin wafer
KB_MS1
LAN1 LED connector
2-pin header
LED_LAN1
LAN2 LED connector
2-pin header
LED_LAN2
Memory card slots
SO-DIMM slot
DIMM1, DIMM2
PCIe x4 slot (x1 mode)
PCIe x4 slot
PCIEX4_1
PCIe Mini slot
52-pin PCIe Mini slot
CN8
Power button
Push button
PWR_SW1
Reset button connector
2-pin wafer
RST_BTN1
SATA 3Gb/s drive connectors
7-pin SATA connector
SATA1, SATA2
SATA power connectors (5 V)
2-pin wafer
SATA_PWR1, SATA_PWR2
Serial ports, RS-232
10-pin header
COM3, COM5, COM6
Serial port, RS-422/485
4-pin wafer
COM4
SMBus connector
4-pin wafer
CN5
Page 18
KINO-ABT-i2 Mini-ITX SBC
Connector
Type
Label
SPDIF connector
5-pin header
SPDIF1
SPI flash connector
6-pin wafer
JSPI1
SPI flash connector (EC)
6-pin wafer
JSPI2
TPM connector
20-pin header
TPM1
USB 2.0 connectors
8-pin header
USB1, USB2
Table 3-1: Peripheral Interface Connectors
3.1.3 External Interface Panel Connectors
The table below lists the connectors on the external I/O panel.
Connector
Type
Label
Audio connectors
Audio jack
CN13
Ethernet and USB 2.0 combo connector
RJ-45 and USB 2.0
LAN2_USB2
Ethernet and USB 3.0 combo connector
RJ-45 and USB 3.0
LAN1_USB1
HDMI connector
HDMI
HDMI1
Serial port connectors
D-sub 9, male
COM1
VGA connector
D-sub 15, female
CRT1
Table 3-2: Rear Panel Connectors
3.2 Internal Peripheral Connectors
The section describes all of the connectors on the KINO-ABT-i2.
3.2.1 ATX Power Connector
CN Label:
ATX1
CN Type:
24-pin connector
CN Location:
See Figure 3-2
CN Pinouts:
See Table 3-3
The ATX power input connector provides power to the system.
Page 19
KINO-ABT-i2 Mini-ITX SBC
Figure 3-2: ATX Power Connector Location
Pin
Description
Pin
Description
1
+3.3 V
13
+3.3 V
2
+3.3 V
14
-12 V
3
GND
15
GND
4
+5 V
16
PS_ON
5
GND
17
GND
6
+5 V
18
GND
7
GND
19
GND
8
PW-OK
20
-5 V
9
5 VSB
21
+5 V
10
+12 V
22
+5 V
11
+12 V
23
+5 V
12
+3.3 V
24
GND
Table 3-3: ATX Power Connector Pinouts
3.2.2 Audio Connector
CN Label:
FRONT-PANEL1
CN Type:
10-pin header
CN Location:
See Figure 3-3
CN Pinouts:
See Table 3-4
This connector connects to speakers, a microphone and an audio input.
Page 20
KINO-ABT-i2 Mini-ITX SBC
Figure 3-3: Audio Connector Location
Pin
Description
Pin
Description
1
MIC2-L
2
GND
3
MIC2-R
4
Presence#
5
LINE2-R
6
MIC2-JD
7
FRONT-IO
8
NC
9
LINE2-L
10
LINE2-JD
Table 3-4: Audio Connector Pinouts
3.2.3 Battery Connector
CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Only
certified engineers should replace the on-board battery.
Dispose of used batteries according to instructions and local
regulations.
CN Label:
BAT1
CN Type:
2-pin wafer
CN Location:
See Figure 3-4
CN Pinouts:
See Table 3-5
Page 21
KINO-ABT-i2 Mini-ITX SBC
A system battery is placed in the battery holder. The battery provides power to the system
clock to retain the time when power is turned off.
Figure 3-4: Battery Connector Location
Pin
Description
1
VBATT
2
GND
Table 3-5: Battery Connector Pinouts
3.2.4 Chassis Intrusion Connector
CN Label:
CHASSIS1
CN Type:
2-pin header
CN Location:
See Figure 3-5
CN Pinouts:
See Table 3-6
6
The chassis intrusion connector is for a chassis intrusion detection sensor or switch that
detects if a chassis component is removed or replaced.
Page 22
KINO-ABT-i2 Mini-ITX SBC
Figure 3-5: Chassis Intrusion Connector Location
Pin
Description
1
+V3.3A_EC
2
CHASSIS_EC
Table 3-6: Chassis Intrusion Connector Pinouts
3.2.5 Digital I/O Connector
CN Label:
DIO1
CN Type:
10-pin header
CN Location:
See Figure 3-6
CN Pinouts:
See Table 3-7
The digital I/O connector provides programmable input and output for external devices.
The digital I/O provides 4-bit output and 4-bit input.
Page 23
KINO-ABT-i2 Mini-ITX SBC
Figure 3-6: Digital I/O Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
+5V
3
DOUT3
4
DOUT2
5
DOUT1
6
DOUT0
7
DIN3
8
DIN2
9
DIN1
10
DIN0
Table 3-7: Digital I/O Connector Pinouts
3.2.6 DisplayPort Connector
CN Label:
DP1
CN Type:
20-pin header
CN Location:
See Figure 3-7
CN Pinouts:
See Table 3-8
The internal DisplayPort connector supports HDMI, LVDS, VGA, DVI, DP connections
with up to 3840 x 2160 resolutions.
Page 24
KINO-ABT-i2 Mini-ITX SBC
Figure 3-7: DisplayPort Connector Location
Pin
Description
Pin
Description
1
HPD
11
LANE3N
2
AUXP
12
GND
3
GND
13
GND
4
AUXN
14
LANE0P
5
AUX_CTRL_DET_D
15
LANE1P
6
GND
16
LANE0N
7
GND
17
LANE1N
8
LANE2P
18
+3.3V
9
LANE3P
19
+5V
10
LANE2N
Table 3-8: DisplayPort Connector Pinouts
3.2.7 EC Debug Connector
CN Label:
CN9
CN Type:
18-pin header
CN Location:
See Figure 3-8
CN Pinouts:
See Table 3-9
The EC debug connector is used for EC debug.
Page 25
KINO-ABT-i2 Mini-ITX SBC
Figure 3-8: EC Debug Connector Location
Pin
Description
Pin
Description
1
EC_EPP_STB#
2
EC_EPP_AFD#
3
EC_EPP_PD0
4
NC
5
EC_EPP_PD1
6
EC_EPP_INIT#
7
EC_EPP_PD2
8
EC_EPP_SLIN#
9
EC_EPP_PD3
10
GND
11
EC_EPP_PD4
12
NC
13
EC_EPP_PD5
14
EC_EPP_BUSY
15
EC_EPP_PD6
16
EC_EPP_KSI5
17
EC_EPP_PD7
18
EC_EPP_KSI4
Table 3-9: EC Debug Connector Pinouts
3.2.8 Fan Connector (CPU)
CN Label:
CPU_FAN1
CN Type:
4-pin wafer
CN Location:
See Figure 3-9
CN Pinouts:
See Table 3-10
The fan connector attaches to a CPU cooling fan.
Page 26
KINO-ABT-i2 Mini-ITX SBC
Figure 3-9: CPU Fan Connector Location
PIN NO.
DESCRIPTION
1
GND
2
+12 V
3
FAN_IO
4
PWM
Table 3-10: CPU Fan Connector Pinouts
3.2.9 Fan Connector (System)
CN Label:
SYS_FAN1
CN Type:
4-pin wafer
CN Location:
See Figure 3-10
CN Pinouts:
See Table 3-11
Each fan connector attaches to a system cooling fan.
Page 27
KINO-ABT-i2 Mini-ITX SBC
Figure 3-10: System Fan Connector Location
PIN NO.
DESCRIPTION
1
GND
2
+12 V
3
FAN_IO
4
PWM
Table 3-11: System Fan Connector Pinouts
3.2.10 Front Panel Connector
CN Label:
F_PANEL1
CN Type:
14-pin header
CN Location:
See Figure 3-11
CN Pinouts:
See Table 3-12
The front panel connector connects to the indicator LEDs and buttons on the computer's
front panel.
Page 28
KINO-ABT-i2 Mini-ITX SBC
Figure 3-11: Front Panel Connector Location
FUNCTION
PIN
DESCRIPTION
FUNCTION
PIN
DESCRIPTION
Power LED
1
PWR_LED+
Speaker
2
Speaker+
3
NC
IPMI LED
4
IPMI_LED+
5
PWR_LED-
6
IPMI_LED-
7
PWR_BTN+
8
Speaker-
9
PWR_BTN-
10
NC
11
HDD_LED+
12
Reset+
13
HDD_LED-
14
Reset-
Power Button
HDD LED
Speaker
Reset Button
Table 3-12: Front Panel Connector Pinouts
3.2.11 iRIS Module Slot
CN Label:
IPMI1
CN Type:
204-pin SOM-DIMM slot
CN Location:
See Figure 3-12
6
The iRIS module slot is used to install the IEI iRIS-2400 IPMI 2.0 module.
Page 29
KINO-ABT-i2 Mini-ITX SBC
WARNING:
The iRIS module slot is designed to install the IEI iRIS-2400 IPMI 2.0
module only. DO NOT install other modules into the iRIS module slot.
Doing so may cause damage to the KINO-ABT-i2.
Figure 3-12: iRIS Module Slot Location
3.2.12 Keyboard and Mouse Connector
CN Label:
KB_MS1
CN Type:
6-pin wafer
CN Location:
See Figure 3-13
CN Pinouts:
See Table 3-13
The keyboard and mouse connector connects to a PS/2 Y-cable that can be connected to
a PS/2 keyboard and mouse.
Page 30
KINO-ABT-i2 Mini-ITX SBC
Figure 3-13: Keyboard and Mouse Connector Location
Pin
Description
1
VCC
2
Mouse Data
3
Mouse Clock
4
Keyboard Data
5
Keyboard Clock
6
GND
Table 3-13: Keyboard and Mouse Connector Pinouts
3.2.13 LAN LED Connectors
CN Label:
LED_LAN1, LED_LAN2
CN Type:
2-pin header
CN Location:
See Figure 3-14
CN Pinouts:
See Table 3-14 and Table 3-15
6
6
The LAN LED connectors are used to connect to the LAN LED indicators on the chassis to
indicate users the link activities of the two LAN ports.
Page 31
KINO-ABT-i2 Mini-ITX SBC
Figure 3-14: LAN LED Connector Locations
Pin
Description
1
+3.3 V
2
LAN1_LINK_ACT-
Table 3-14: LAN1 LED Connector Pinouts
Pin
Description
1
+3.3 v
2
LAN2_LINK_ACT-
Table 3-15: LAN2 LED Connector Pinouts
3.2.14 Memory Card Slots
CN Label:
DIMM1, DIMM2
CN Type:
DDR3 SO-DIMM slot
CN Location:
See Figure 3-15
6
The SO-DIMM slots are for installing DDR3 Low Voltage SO-DIMM memory modules.
Page 32
KINO-ABT-i2 Mini-ITX SBC
Figure 3-15: Memory Card Slot Locations
3.2.15 PCIe x4 Slot
CN Label:
PCIEX4_1
CN Type:
PCIe x4 slot
CN Location:
See Figure 3-16
The PCIe x4 interface provides x1 speed for PCIe expansion cards.
Figure 3-16: PCIe x4 Slot Location
3.2.16 PCIe Mini Card Slot
CN Label:
CN8
CN Type:
PCIe Mini card slot
Page 33
KINO-ABT-i2 Mini-ITX SBC
CN Location:
See Figure 3-17
CN Pinouts:
See Table 3-16
6
The PCIe Mini card slot is for installing PCIe Mini expansion cards, such as mSATA
modules or Wi-Fi modules.
Figure 3-17: PCIe Mini Card Slot Location
Pin
Description
Pin
Description
1
PCIE_WAKE#
2
+3.3 V
3
N/C
4
GND
5
N/C
6
+1.5 V
7
N/C
8
N/C
9
GND
10
N/C
11
MSATA_CLK-
12
N/C
13
MSATA_CLK+
14
N/C
15
GND
16
N/C
17
PLTRST_N
18
GND
19
N/C
20
+3.3 V
21
GND
22
PLTRST_N
23
SATA_RX+
24
+3.3 V
25
SATA_RX-
26
GND
Page 34
KINO-ABT-i2 Mini-ITX SBC
Pin
Description
Pin
Description
27
GND
28
+1.5 V
29
GND
30
SMB_CLK
31
SATA_TX-
32
SMBD_ATA
33
SATA_TX+
34
GND
35
GND
36
USB_DATA-
37
GND
38
USB_DATA+
39
+3.3 V
40
GND
41
+3.3 V
42
N/C
43
+3.3 V
44
N/C
45
CLINK_CLK
46
N/C
47
CLINK_DATA
48
+1.5 V
49
CLINK_RST#
50
GND
51
MSATA_DET
52
+3.3 V
Table 3-16: PCIe Mini Card Slot Pinouts
3.2.17 Power Button
CN Label:
PWR_SW1
CN Type:
Push button
CN Location:
See Figure 3-18
The on-board power button controls system power.
Figure 3-18: Power Button Location
Page 35
KINO-ABT-i2 Mini-ITX SBC
3.2.18 Reset Button Connector
CN Label:
RST_BTN1
CN Type:
2-pin wafer
CN Location:
See Figure 3-19
CN Pinouts:
See Table 3-17
The reset button connector is connected to a reset switch on the system chassis.
Figure 3-19: Reset Button Connector Location
Pin
Description
1
PM_SYSRST_R#
2
GND
Table 3-17: Reset Button Connector Pinouts
3.2.19 SATA 3Gb/s Drive Connectors
CN Label:
SATA1, SATA2
CN Type:
7-pin SATA drive connectors
CN Location:
See Figure 3-20
CN Pinouts:
See Table 3-18
Page 36
KINO-ABT-i2 Mini-ITX SBC
The SATA drive connectors can be connected to SATA drives.
Figure 3-20: SATA 3Gb/s Drive Connector Locations
Pin
Description
1
GND
2
SATA_TX+
3
SATA_TX-
4
GND
5
SATA_RX-
6
SATA_RX+
7
GND
Table 3-18: SATA 3Gb/s Drive Connector Pinouts
3.2.20 SATA Power Connectors
CN Label:
SATA_PWR1, SATA_PWR2
CN Type:
2-pin wafer
CN Location:
See Figure 3-21
CN Pinouts:
See Table 3-19
Use the SATA Power Connector to connect to SATA device power connections.
Page 37
KINO-ABT-i2 Mini-ITX SBC
Figure 3-21: SATA Power Connector Locations
Pin
Description
1
+5VS
2
GND
Table 3-19: SATA Power Connector Pinouts
3.2.21 Serial Port Connectors, RS-232
CN Label:
COM3, COM5, COM6
CN Type:
10-pin header
CN Location:
See Figure 3-22
CN Pinouts:
See Table 3-20
The connector provides RS-232 port connection.
Page 38
KINO-ABT-i2 Mini-ITX SBC
Figure 3-22: RS-232 Serial Port Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
SIN
4
RTS
5
SOUT
6
CTS
7
DTR
8
RI
9
GND
10
GND
Table 3-20: RS-232 Serial Port Connector Pinouts
3.2.22 Serial Port Connector, RS-422/485
CN Label:
COM4
CN Type:
4-pin wafer
CN Location:
See Figure 3-23
CN Pinouts:
See Table 3-21
Used for RS-422/485 communications.
Page 39
KINO-ABT-i2 Mini-ITX SBC
Figure 3-23: RS-422/485 Connector Location
PIN NO.
DESCRIPTION
1
RXD422-
2
RXD422+
3
TXD422+/TXD485+
4
TXD422-/TXD485-
Table 3-21: RS-422/485 Connector Pinouts
Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the
D-sub 9 connector are listed below.
RS-422 Pinouts
RS-485 Pinouts
Table 3-22: RS-422/485 Pinouts of D-sub 9 Connector
3.2.23 SMBus Connector
CN Label:
CN5
CN Type:
4-pin wafer
Page 40
KINO-ABT-i2 Mini-ITX SBC
CN Location:
See Figure 3-24
CN Pinouts:
See Table 3-23
The SMBus (System Management Bus) connector provides low-speed system
management communications.
Figure 3-24: SMBus Connector Location
PIN
DESCRIPTION
1
GND
2
SMB_DATA
3
SMB_CLK
4
+5 V
Table 3-23: SMBus Connector Pinouts
3.2.24 SPDIF Connector
CN Label:
SPDIF1
CN Type:
5-pin header
CN Location:
See Figure 3-25
CN Pinouts:
See Table 3-24
Use the SPDIF connector to connect digital audio devices to the system.
Page 41
KINO-ABT-i2 Mini-ITX SBC
Figure 3-25: SPDIF Connector Location
Pin
Description
1
+5 V
2
N/A
3
SPDIF OUT
4
GND
5
SPDIF IN
Table 3-24: SPDIF Connector Pinouts
3.2.25 SPI Flash Connector
CN Label:
JSPI1
CN Type:
6-pin wafer
CN Location:
See Figure 3-26
CN Pinouts:
See Table 3-25
The SPI flash connector is used to flash the SPI ROM.
Page 42
KINO-ABT-i2 Mini-ITX SBC
Figure 3-26: SPI Flash Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+1.8 V
4
SPI_CLK
2
SPI_CS#
5
SPI_SI
3
SPI_SO
6
GND
Table 3-25: SPI Flash Connector Pinouts
3.2.26 SPI Flash Connector, EC
CN Label:
JSPI2
CN Type:
6-pin wafer
CN Location:
See Figure 3-27
CN Pinouts:
See Table 3-26
The SPI flash connector is used to flash the EC ROM.
Page 43
KINO-ABT-i2 Mini-ITX SBC
Figure 3-27: SPI EC Flash Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+1.8 V
4
SPI_CLK
2
SPI_CS#
5
SPI_SI
3
SPI_SO
6
GND
Table 3-26: SPI EC Flash Connector Pinouts
3.2.27 TPM Connector
CN Label:
TPM1
CN Type:
20-pin header
CN Location:
See Figure 3-28
CN Pinouts:
See Table 3-27
The TPM connector connects to a TPM module.
Page 44
KINO-ABT-i2 Mini-ITX SBC
Figure 3-28: TPM Connector Location
Pin
Description
Pin
Description
1
LPC_CLK
2
GND
3
LPC_FRAME#
4
N/A
5
BUF_PLT_RST#
6
+5V
7
LPC_AD3
8
LPC_AD2
9
+3.3V
10
LPC_AD1
11
LPC_AD0
12
GND
13
SMB_CLK
14
SMB_DATA
15
+3.3 V
16
INT_SERIRQ
17
GND
18
PM_GLKRUN#
19
+3.3 V
20
TPM_DRQ#
Table 3-27: TPM Connector Pinouts
3.2.28 USB 2.0 Connectors
CN Label:
USB1, USB2
CN Type:
8-pin header
CN Location:
See Figure 3-29
CN Pinouts:
See Table 3-28 and Table 3-29
Page 45
KINO-ABT-i2 Mini-ITX SBC
The USB 2.0 connector connects to USB 2.0 devices. Each pin header provides two
USB 2.0 ports.
Figure 3-29: USB 2.0 Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+VCC_USB45
2
GND
3
DATA4-
4
DATA5+
5
DATA4+
6
DATA5-
7
GND
8
+VCC_USB45
Table 3-28: USB1 Pinouts
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+VCC_USB67
2
GND
3
DATA6-
4
DATA7+
5
DATA6+
6
DATA7-
7
GND
8
+VCC_USB67
Table 3-29: USB2 Pinouts
Page 46
KINO-ABT-i2 Mini-ITX SBC
3.3 External Peripheral Interface Connector Panel
The figure below shows the external peripheral interface connector (EPIC) panel. The
EPIC panel consists of the following:
Figure 3-30: External Peripheral Interface Connector
3.3.1 Audio Connector
CN Label:
CN13
CN Type:
Audio jacks
CN Location:
See Figure 3-30
The audio jacks connect to external audio devices.

Line In port (Light Blue): Connects a CD-ROM, DVD player, or other audio
devices.

Line Out port (Lime): Connects to a headphone or a speaker. With
multi-channel configurations, this port can also connect to front speakers.

Microphone (Pink): Connects a microphone.
Page 47
KINO-ABT-i2 Mini-ITX SBC
Figure 3-31: Audio Connector
3.3.2 Ethernet and USB 2.0 Combo Connector
CN Label:
LAN2_USB2
CN Type:
RJ-45 and USB 2.0 connector
CN Location:
See Figure 3-30
CN Pinouts:
See Table 3-30 and Table 3-32
A 10/100/1000 Mb/s connection can be made to a Local Area Network.
Pin
Description
Pin
Description
L1
TRD2P0
L5
TRD2N2
L2
TRD2N0
L6
TRD2N1
L3
TRD2P1
L7
TRD2P3
L4
TRD2P2
L8
TRD2N3
Table 3-30: LAN2 Ethernet Connector Pinouts
Figure 3-32: Ethernet Connector
Page 48
KINO-ABT-i2 Mini-ITX SBC
LED
Description
LED
Description
A
on: linked
B
off: 10 Mb/s
blinking: data is being sent/received
green: 100 Mb/s
orange: 1000 Mb/s
Table 3-31: Connector LEDs
The USB 2.0 connector can be connected to a USB 2.0 device.
Pin
Description
Pin
Description
1
VCC
5
VCC
2
USB_DATA-
6
USB_DATA-
3
USB_DATA+
7
USB_DATA+
4
GND
8
GND
Table 3-32: USB 2.0 Port Pinouts
3.3.3 Ethernet and USB 3.0 Combo Connector
CN Label:
LAN1_USB1
CN Type:
RJ-45 and USB 3.0 connector
CN Location:
See Figure 3-30
CN Pinouts:
See Table 3-33 and Table 3-35
A 10/100/1000 Mb/s connection can be made to a Local Area Network. The LAN1
Ethernet connector supports IPMI 2.0.
Pin
Description
Pin
Description
20
LAN1_MDI0P
24
LAN1_MDI2P
21
LAN1_MDI0N
25
LAN1_MDI2N
22
LAN1_MDI1P
26
LAN1_MDI3P
23
LAN1_MDI1N
27
LAN1_MDI3N
Table 3-33: LAN1 Ethernet Connector Pinouts
Page 49
KINO-ABT-i2 Mini-ITX SBC
Figure 3-33: Ethernet Connector
LED
Description
LED
Description
A
on: linked
B
off: 10 Mb/s
blinking: data is being sent/received
green: 100 Mb/s
orange: 1000 Mb/s
Table 3-34: Connector LEDs
The USB 3.0 connector can be connected to a USB device.
Pin
Description
Pin
Description
1
VCC
10
VCC
2
USB_DATA-
11
USB_DATA-
3
USB_DATA+
12
USB_ DATA+
4
GND
13
GND
5
USB3_RX-
14
USB3_RX-
6
USB3_RX+
15
USB3_ RX+
7
GND
16
GND
8
USB3_TX-
17
USB3_TX-
9
USB3_TX+
18
USB3_TX+
Table 3-35: USB 3.0 Port Pinouts
3.3.4 HDMI Connector
CN Label:
HDMI1
CN Type:
23-pin HDMI port
CN Location:
See Figure 3-30
CN Pinouts:
See Table 3-36 and Figure 3-34
Page 50
KINO-ABT-i2 Mini-ITX SBC
The HDMI connector can connect to an HDMI device. The HDMI connector supports up to
2560 x 1600 resolutions.
Pin
Description
Pin
Description
1
HDMI_DATA2
2
GND
3
HDMI_DATA2#
4
HDMI_DATA1
5
GND
6
HDMI_DATA1#
7
HDMI_DATA0
8
GND
9
HDMI_DATA0#
10
HDMI_CLK
11
GND
12
HDMI_CLK#
13
N/C
14
N/C
15
HDMI_SCL
16
HDMI_SDA
17
GND
18
+5V
19
HDMI_HPD
20
HDMI_GND
21
HDMI_GND
22
HDMI_GND
23
HDMI_GND
Table 3-36: HDMI Connector Pinouts
Figure 3-34: HDMI Connector
3.3.5 Serial Port Connectors (COM1 and COM2)
CN Label:
COM1
CN Type:
D-sub 9
CN Location:
See Figure 3-30
CN Pinouts:
See Table 3-37 and Figure 3-35
The serial port connects to a RS-232 serial communications device.
Pin
Description
Pin
Description
1
DCD
6
DSR
Page 51
KINO-ABT-i2 Mini-ITX SBC
Pin
Description
Pin
Description
2
RX
7
RTS
3
TX
8
CTS
4
DTR
9
RI
5
GND
Table 3-37: Serial Port Pinouts
Figure 3-35: Serial Port Pinouts
3.3.6 VGA Connector
CN Label:
CRT1
CN Type:
D-sub 15 female
CN Location:
See Figure 3-30
CN Pinouts:
See Table 3-38 and Figure 3-36
The VGA connector can be connected to monitors that accept standard VGA input for
easy dual display setup. The VGA connector supports up to 2560 x 1600 resolutions.
PIN
DESCRIPTION
PIN
DESCRIPTION
V1
RED
V2
GREEN
V3
BLUE
V4
NC
V5
GND
V6
GND
V7
GND
V8
GND
V9
VCC
V10
GND
V11
NC
V12
DDCDA
V13
HSYNC
V14
VSYNC
V15
DDCCLK
Table 3-38: VGA Connector Pinouts
Page 52
KINO-ABT-i2 Mini-ITX SBC
Figure 3-36: VGA Connector
Page 53
KINO-ABT-i2 Mini-ITX SBC
Chapter
4
4 Installation
Page 54
KINO-ABT-i2 Mini-ITX SBC
4.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
KINO-ABT-i2 may result in permanent damage to the KINO-ABT-i2 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the KINO-ABT-i2. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the KINO-ABT-i2 or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.

Wear an anti-static wristband: - Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.

Self-grounding:- Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.

Use an anti-static pad: When configuring the KINO-ABT-i2, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
KINO-ABT-i2.

Only handle the edges of the PCB:-: When handling the PCB, hold the PCB
by the edges.
4.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before installation. All installation notices must
be strictly adhered to. Failing to adhere to these precautions may lead
to severe damage and injury to the person performing the installation.
Page 55
KINO-ABT-i2 Mini-ITX SBC
WARNING:
The installation instructions described in this manual should be
carefully followed in order to prevent damage to the components and
injury to the user.
Before and during the installation please DO the following:

Read the user manual:
o
The user manual provides a complete description of the KINO-ABT-i2
installation instructions and configuration options.

Wear an electrostatic discharge cuff (ESD):
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.

Place the KINO-ABT-i2 on an antistatic pad:
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.

Turn all power to the KINO-ABT-i2 off:
o
When working with the KINO-ABT-i2, make sure that it is disconnected
from all power supplies and that no electricity is being fed into the system.
Before and during the installation of the KINO-ABT-i2 DO NOT:

Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.

Use the product before verifying all the cables and power connectors are
properly connected.

Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
Page 56
KINO-ABT-i2 Mini-ITX SBC
4.2.1 SO-DIMM Installation
To install an SO-DIMM, please follow the steps below and refer to Figure 4-1.
Figure 4-1: SO-DIMM Installation
Step 1: Locate the SO-DIMM socket on the solder side of the KINO-ABT-i2. Place the
board on an anti-static mat.
Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the
notch on the memory socket.
Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-1)
Step 4: Seat the SO-DIMM. Gently push downwards and the arms clip into place. (See
Figure 4-1)
4.2.2 iRIS-2400 Module Installation
WARNING:
The iRIS module slot is designed to install the IEI iRIS-2400 IPMI 2.0
module only. DO NOT install other modules into the iRIS module slot.
Doing so may cause damage to the KINO-ABT-i2.
To install the iRIS-2400 module, please follow the steps below and refer to Figure 4-2.
Page 57
KINO-ABT-i2 Mini-ITX SBC
Figure 4-2: iRIS Module Installation
Step 1: Locate the iRIS module slot. See Figure 3-12.
Step 2: Open the socket handles. Open the two handles outwards as far as they can.
See Figure 4-2.
Step 3: Align the iRIS-2400 module with the socket. Align the iRIS-2400 module so
the notch on the module lines up with the notch on the socket. See Figure 4-2.
Step 4: Insert the iRIS-2400 module. Once aligned, press down until the iRIS-2400
module is properly seated. Clip the two handles into place. See Figure 4-2.
Step 5: Removing the iRIS-2400 module. To remove the iRIS-2400 module, push both
handles outward. The module is ejected by a mechanism in the socket.
NOTE:
After installing the iRIS-2400 module, use LAN1_USB1 port to
establish a network connection. Please refer to Section 4.6 for IPMI
setup procedures.
Page 58
KINO-ABT-i2 Mini-ITX SBC
4.2.3 PCIe Mini Card Installation
To install the PCIe Mini card, please refer to the diagram and instructions below.
NOTE:
The PCIe Mini card slot supports full-size and half-size PCIe Mini
cards. The following instruction diagrams take full-size cards as an
example to show users how to install. To install a half-size card, please
remove the corresponding retention screw.
Step 1: Locate the PCIe Mini card slot. Remove the preinstalled retention screw on the
screw pillar of the PCIe Mini card slot as shown in (Figure 4-3).
6
Figure 4-3: PCIe Mini Card Retention Screw Removal
Step 2: Line up the notch on the PCIe Mini card with the notch on the connector. Slide
the PCIe Mini card into the socket at an angle of about 20º.
Step 3: Push the other end of the PCIe Mini card down and secure the card with the
previously removed retention screw (Figure 4-4).
6
Page 59
KINO-ABT-i2 Mini-ITX SBC
Figure 4-4: PCIe Mini Card Installation (Full-size)
4.3 System Configuration
The KINO-ABT-i2 is a jumperless single board computer. The system configuration is
controlled by buttons and switches. The system configuration must be performed before
installation.
4.3.1 AT/ATX Power Mode Setting
The AT and ATX power mode selection is made through the AT/ATX power mode switch
which is shown in Figure 4-5.
Figure 4-5: AT/ATX Power Mode Switch Location
Page 60
KINO-ABT-i2 Mini-ITX SBC
4.3.2 Clear CMOS Button
To reset the BIOS, remove the on-board battery and press the clear CMOS button for
three seconds or more. The clear CMOS button location is shown in Figure 4-6.
Figure 4-6: Clear CMOS Button Location
4.3.3 Flash Descriptor Security Override
The Flash Descriptor Security Override jumper (J_FLASH1) specifies whether to override
the flash descriptor.
Setting
Description
Short 1-2
No override
Short 2-3
Override
Table 4-1: Flash Descriptor Security Override Jumper Settings
Figure 4-7: Flash Descriptor Security Override Jumper Location
Page 61
KINO-ABT-i2 Mini-ITX SBC
4.3.4 mSATA/SATA Selection
Use the J_SATA1 switch to select whether to automatically detect mSATA devices.
Setting
Description
A-B
Automatically detect mSATA device (Default)
B-C
Enable mSATA device
Table 4-2: mSATA/SATA Switch Settings
Figure 4-8: mSATA/SATA Switch Location
4.3.5 USB Power Select
The USB power selection is made through the BIOS options in “Chipset  South Bridge”
BIOS menu. Use the USB SW1 and the USB SW2 BIOS options to configure the power
source to the corresponding USB ports (see Table 4-3).
BIOS Options
USB SW1
USB SW2
Configured USB Ports
LAN1_USB1 (external USB 3.0 ports)
LAN2_USB2 (external USB 2.0 ports)
USB1, USB2 (internal USB 2.0 ports)
Table 4-3: BIOS Options and Configured USB Ports
Please refer to Section for detailed information.
Page 62
KINO-ABT-i2 Mini-ITX SBC
4.4 Internal Peripheral Device Connections
This section outlines the installation of peripheral devices to the on-board connectors.
4.4.1 SATA Drive Connection
The KINO-ABT-i2 is shipped with two SATA drive cables. To connect the SATA drive to
the connector, please follow the steps below.
Step 1: Locate the SATA connector and the SATA power connector. The locations of
the connectors are shown in Chapter 3.
Step 2: Insert the cable connector. Insert the cable connector into the on-board SATA
drive connector and the SATA power connector. See Figure 4-9.
Figure 4-9: SATA Drive Cable Connection
Step 3: Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SATA drive. See Figure 4-9.
Step 4: To remove the SATA cable from the SATA connector, press the clip on the
connector at the end of the cable.
Page 63
KINO-ABT-i2 Mini-ITX SBC
4.4.2 USB Cable Connection
The KINO-ABT-i2 is shipped with a dual port USB 2.0 cable. To connect the USB cable
connector, please follow the steps below.
Step 1: Locate the connectors. The locations of the USB connectors are shown in
Chapter 3.
WARNING:
If the USB pins are not properly aligned, the USB device can burn out.
Step 2: Align the connectors. The cable has two connectors. Correctly align pin 1on
each cable connector with pin 1 on the KINO-ABT-i2 USB connector.
Step 3: Insert the cable connectors. Once the cable connectors are properly aligned
with the USB connectors on the KINO-ABT-i2, connect the cable connectors to
the on-board connectors. See Figure 4-10.
Figure 4-10: Dual USB Cable Connection
Step 4: Attach the USB connectors to the chassis. The USB 2.0 connectors each of
two retention screw holes. To secure the connectors to the chassis please refer
to the installation instructions that came with the chassis.Step 0:
Page 64
KINO-ABT-i2 Mini-ITX SBC
4.5 External Peripheral Interface Connection
This section describes connecting devices to the external connectors on the KINO-ABT-i2.
4.5.1 Audio Connector
The audio jacks on the external audio connector enable the KINO-ABT-i2 to be connected
to a stereo sound setup. To install the audio devices, follow the steps below.
Step 1: Identify the audio plugs. The plugs on your home theater system or speakers
may not match the colors on the rear panel. If audio plugs are plugged into the
wrong jacks, sound quality will be very bad.
Step 2: Plug the audio plugs into the audio jacks. Plug the audio plugs into the audio
jacks. If the plugs on your speakers are different, an adapter will need to be
used to plug them into the audio jacks.

Line In port (Light Blue): Connects a CD-ROM, DVD player, or other audio
devices.

Line Out port (Lime): Connects to a headphone or a speaker.

Microphone (Pink): Connects to a microphone.
Figure 4-11: Audio Connector
Page 65
KINO-ABT-i2 Mini-ITX SBC
Step 3: Check audio clarity. Check that the sound is coming through the right speakers
by adjusting the balance front to rear and left to right. Step 0:
4.5.2 HDMI Display Device Connection
The HDMI connector transmits a digital signal to compatible HDMI display devices such
as a TV or computer screen. To connect the HDMI cable to the KINO-ABT-i2, follow the
steps below.
Step 1: Locate the HDMI connector. The location is shown in Chapter 3.
Step 2: Align the connector. Align the HDMI connector with the HDMI port. Make sure
the orientation of the connector is correct.
Figure 4-12: HDMI Connection
Step 3: Insert the HDMI connector. Gently insert the HDMI connector. The connector
should engage with a gentle push. If the connector does not insert easily, check
again that the connector is aligned correctly, and that the connector is being
inserted with the right way up.
Page 66
KINO-ABT-i2 Mini-ITX SBC
4.5.3 LAN Connection
There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection
to an external network. To connect a LAN cable with an RJ-45 connector, please follow
the instructions below.
Step 1: Locate the RJ-45 connectors. The locations of the LAN connectors are shown
in Chapter 3.
Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of
the RJ-45 connectors on the KINO-ABT-i2. See Figure 4-13.
Figure 4-13: LAN Connection
Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN
cable RJ-45 connector into the on-board RJ-45 connector.
4.5.4 USB Connection
The external USB Series "A" receptacle connectors provide easier and quicker access to
external USB devices. Follow the steps below to connect USB devices to the
KINO-ABT-i2.
Page 67
KINO-ABT-i2 Mini-ITX SBC
Step 1: Locate the USB Series "A" receptacle connectors. The location of the USB
Series "A" receptacle connectors are shown in Chapter 3.
Step 2: Insert a USB Series "A" plug. Insert the USB Series "A" plug of a device into
the USB Series "A" receptacle on the external peripheral interface. See
Figure 4-14.
Figure 4-14: USB Connector
4.5.5 Serial Device Connection
The KINO-ABT-i2 has two male D-sub 9 connectors on the external peripheral interface
panel for serial devices. Follow the steps below to connect a serial device to the
KINO-ABT-i2.
Step 1: Locate the D-sub 9 connectors. The locations of the D-sub 9 connectors are
shown in Chapter 3.
Step 2: Insert the serial connector. Insert the D-sub 9 connector of a serial device into
the D-sub 9 connector on the external peripheral interface. See Figure 4-15.
Page 68
KINO-ABT-i2 Mini-ITX SBC
Figure 4-15: Serial Device Connector
Step 3: Secure the connector. Secure the serial device connector to the external
interface by tightening the two retention screws on either side of the connector.
4.5.6 VGA Monitor Connection
The KINO-ABT-i2 has one single female D-sub 15 connector on the external peripheral
interface panel. The D-sub 15 connector is connected to a CRT or VGA monitor. To
connect a monitor to the KINO-ABT-i2, please follow the instructions below.
Step 1: Locate the female D-sub 15 connector. The location of the female D-sub 15
connector is shown in Chapter 3.
Step 2: Align the VGA connector. Align the male D-sub 15 connector on the VGA
screen cable with the female D-sub 15 connector on the external peripheral
interface.
Page 69
KINO-ABT-i2 Mini-ITX SBC
Step 3: Insert the VGA connector. Once the connectors are properly aligned, insert the
male connector from the VGA screen into the female connector on the
KINO-ABT-i2. See Figure 4-16.
Figure 4-16: VGA Connector
Step 4: Secure the connector. Secure the D-sub 15 VGA connector from the VGA
monitor to the external interface by tightening the two retention screws on either
side of the connector. Step 0:
4.6 IPMI Setup Procedure
The KINO-ABT-i2 features Intelligent Platform Management Interface (IPMI) that helps
lower the overall costs of server management by enabling users to maximize IT resources,
save time and manage multiple systems. The KINO-ABT-i2 supports IPMI 2.0 through the
optional iRIS-2400 module. Follow the steps below to setup IPMI.
4.6.1 Managed System Hardware Setup
The hardware configuration of the managed system (KINO-ABT-i2) is described below.
Step 1: Install an iRIS-2400 module to the IPMI module socket (refer to Section 4.2.2).
Page 70
KINO-ABT-i2 Mini-ITX SBC
Step 2: Make sure at least one DDR3 SO-DIMM is installed in one of the SO-DIMM
sockets. If multiple SO-DIMMs are installed, all of the SO-DIMMs must be same
size, same speed and same brand to get the best performance.
Step 3: Connect an Ethernet cable to the RJ-45 connector labeled LAN1_USB1
(Figure 3-30).
4.6.2 Using the IEI iMAN Web GUI
To manage a client system from a remote console using IEI iMAN Web GUI, follow the
steps below.
Step 1: Obtain the IP address of the managed system. It is recommended to use the
IPMI Tool on the managed system to obtain the IP address. To use IPMI Tool to
obtain IP address, follow the steps below:
a. Copy the Ipmitool.exe file to a bootable USB flash drive.
b. Insert the USB flash drive to the KINO-ABT-i2
c. The KINO-ABT-i2 boots from the USB flash drive
d. Enter the following command: ipmitool 20 30 02 01 03 00 00
(there is a space between each two-digit number)
e. A serial of number shows. The last four two-digit hexadecimal numbers are
the IP address. Convert the hexadecimal numbers to decimal numbers.
Step 2: On the remote management console, open a web browser. Enter the managed
system IP address in the web browser (Figure 4-17).
Figure 4-17: IEI iMAN Web Address
Step 3: The login page appears in the web browser.
Step 4: Enter the user name and password to login the system. The default login
username and password are:
Page 71
KINO-ABT-i2 Mini-ITX SBC
-Username: admin
-Password: admin
Step 5: Press the login button to login the system.
Step 6: The IEI iMAN Web Interface appears. Step0:
Figure 4-18: IEI iMAN Web GUI
NOTE:
To understand how to use the IEI iMAN Web GUI, please refer to the
iRIS-2400 Web GUI user manual in the utility CD came with the
KINO-ABT-i2. The user manual describes each function in detail.
Page 72
KINO-ABT-i2 Mini-ITX SBC
Chapter
5
5 BIOS
Page 73
KINO-ABT-i2 Mini-ITX SBC
5.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
NOTE:
Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.
5.1.1 Starting Setup
The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DEL or F2 key as soon as the system is turned on or
2. Press the DEL or F2 key when the “Press DEL or F2 to enter SETUP”
message appears on the screen.
If the message disappears before the DEL or F2 key is pressed, restart the computer and
try again.
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation
keys are shown in Table 5-1.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
+
Increase the numeric value or make changes
Page 74
KINO-ABT-i2 Mini-ITX SBC
Key
Function
-
Decrease the numeric value or make changes
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 key
Load previous values
F3 key
Load optimized defaults
F4 key
Save changes and Exit BIOS
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC
or the F1 key again.
5.1.4 Unable to Reboot after Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the clear CMOS button described in Chapter 4.
5.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:

Main – Changes the basic system configuration.

Advanced – Changes the advanced system settings.

Chipset – Changes the chipset settings.

Boot – Changes the system boot configuration.

Security – Sets User and Supervisor Passwords.

Save & Exit – Selects exit options and loads default settings
Page 75
KINO-ABT-i2 Mini-ITX SBC
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
5.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
BIOS Information
BIOS Vendor
Core Version
Compliency
Project Version
Build Date and Time
American Megatrends
5.009
UEFI 2.3;PI1.2
B311AM11.ROM
08/13/2014 08:49:21
iWDD Vendor
iWDD Version
iEi
B311ER12.bin
IPMI Card Status
Not Present
Memory Information
Total Memory
4096 MB (LPDDR3)
Set the Date. Use Tab to
switch between Data
elements.
----------------------
: Select Screen
 : Select Item
00.05.00.00
Enter Select
01.00.02.1060
+ -: Change Opt.
F1: General Help
System Date
[Tue 01/13/2010]
F2: Previous Values
System Time
[15:10:27]
F3: Optimized Defaults
F4: Save & Exit
Access Level
Administrator
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
TXE Information
Sec RC Version
TXE FW Version
BIOS Menu 1: Main

BIOS Information
The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information
cannot be changed. The items shown in the system overview include:
Page 76

BIOS Vendor: Installed BIOS vendor

Core Version: Current BIOS version

Compliency: Current compliant version

Project Version: the board version
KINO-ABT-i2 Mini-ITX SBC


Build Date and Time: Date and time the current BIOS version was made
Memory Information
The Memory Information lists a brief summary of the system memory. The fields in
Memory Information cannot be changed. The items shown in the system overview
include:


Total Memory: Current total memory of the system
TXE Information
The TXE Information lists a brief summary of Intel® Trusted Execution Engine (TXE).
The fields in TXE Information cannot be changed. The items shown in the system
overview include:

Sec RC Version: Current sec reference code version

TXE FW Version: Current Intel® TXE firmware version
The System Overview field has two user configurable fields:

System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.

System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
Page 77
KINO-ABT-i2 Mini-ITX SBC
5.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING!
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
>
>
>
>
>
>
>
>
>
ACPI Settings
Super IO Configuration
iWDD Hardware Monitor
RTC Wake Settings
Serial Port Console Redirection
CPU Configuration
IDE Configuration
Trusted Computing
USB Configuration
System ACPI Parameters
----------------------
: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 2: Advanced
5.3.1 ACPI Settings
The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and
Power Interface (ACPI) options.
Page 78
KINO-ABT-i2 Mini-ITX SBC
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State
[S3 (Suspend to RAM)]
Select the highest ACPI
sleep state the system
will enter when the
SUSPEND button is
pressed.
---------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 3: ACPI Configuration

ACPI Sleep State [S3 (Suspend to RAM)]
Use the ACPI Sleep State option to specify the sleep state the system enters when it is
not being used.

S3
(Suspend
RAM)
to
DEFAULT
The caches are flushed and the CPU is powered
off. Power to the RAM is maintained. The
computer returns slower to a working state, but
more power is saved.
Page 79
KINO-ABT-i2 Mini-ITX SBC
5.3.2 Super IO Configuration
Use the Super IO Configuration menu (BIOS Menu 4) to set or change the
configurations for the serial ports.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
F81866 Super IO Configuration
F81866 Super IO
> Serial Port 1
> Serial Port 2
> Serial Port 3
> Serial Port 4
> Serial Port 5
> Serial Port 6
Chip
Configuration
Configuration
Configuration
Configuration
Configuration
Configuration
Set Parameters of Serial
Port 1 (COMA)
F81866
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 4: Super IO Configuration
5.3.2.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (BIOS Menu 5) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Serial Port n Configuration
Serial Port
Device Settings
Enable or Disable Serial
Port (COM)
[Enabled]
IO=3F8h;IRQ=4
--------------------: Select Screen
 : Select Item
Enter Select
= - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
Change Settings
[Auto]
BIOS Menu 5: Serial Port n Configuration Menu
Page 80
KINO-ABT-i2 Mini-ITX SBC
5.3.2.1.1 Serial Port 1 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.


IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=4
address is IRQ4
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Page 81
KINO-ABT-i2 Mini-ITX SBC
5.3.2.1.2 Serial Port 2 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.


IO=2F8h;
Serial Port I/O port address is 2F8h and the interrupt
IRQ=3
address is IRQ3
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
4,
5, 6, 7, 9,
10, 11, 12
Page 82
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
KINO-ABT-i2 Mini-ITX SBC

Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12
5.3.2.1.3 Serial Port 3 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.


IO=3E8h;
Serial Port I/O port address is 3E8h and the interrupt
IRQ=10
address is IRQ10
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Page 83
KINO-ABT-i2 Mini-ITX SBC

Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F0h and the interrupt
IO=2F0h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2E0h and the interrupt
IO=2E0h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12
5.3.2.1.4 Serial Port 4 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.
Page 84
KINO-ABT-i2 Mini-ITX SBC


IO=2E8h;
Serial Port I/O port address is 2E8h and the interrupt
IRQ=10
address is IRQ10
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F0h and the interrupt
IO=2F0h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2E0h and the interrupt
IO=2E0h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
5.3.2.1.5 Serial Port 5 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Page 85
KINO-ABT-i2 Mini-ITX SBC


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.


IO=2D0h;
Serial Port I/O port address is 2D0h and the interrupt
IRQ=11
address is IRQ11
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F0h and the interrupt
IO=2F0h;
IRQ=3,
4,
5, 6, 7, 9,
10, 11, 12
Page 86
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
KINO-ABT-i2 Mini-ITX SBC

Serial Port I/O port address is 2E0h and the interrupt
IO=2E0h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12
5.3.2.1.6 Serial Port 6 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.


IO=2D8h;
Serial Port I/O port address is 2D8h and the interrupt
IRQ=11
address is IRQ11
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Page 87
KINO-ABT-i2 Mini-ITX SBC

Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2F0h and the interrupt
IO=2F0h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12

Serial Port I/O port address is 2E0h and the interrupt
IO=2E0h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
5.3.3 iWDD Hardware Monitor
The iWDD Hardware Monitor menu (BIOS Menu 6) contains the fan configuration
submenus and displays operating temperature and system voltages.
Page 88
KINO-ABT-i2 Mini-ITX SBC
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
PC Health Status
> Smart Fan Function
CPU temperature
System temperature
CPU Fan Speed
SYS_Fan Speed
+VCC_CORE
+5VS
+V12S
+V1.35
+3.3A
+3.3V
:+36 °C
:N/A
:N/A
:N/A
:+0.812 V
:+4.983 V
:+12.122 V
:+1.339 V
:+3.307 V
:+3.329 V
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 6: iWDD Hardware Monitor

Smart Fan Function
Use the Smart Fan Function BIOS option to enable or disable the smart fan connected to
the system.


Disabled

Enabled
Disables the smart fan.
DEFAULT
Enables the smart fan.
PC Health Status
The following system parameters and values are shown. The system parameters that are
monitored are:

System Temperatures:
o
o

System Temperature
Fan Speeds:
o
o

CPU Temperature
CPU Fan
System Fan
Voltages:
o
o
+VCC_CORE
+5VS
Page 89
KINO-ABT-i2 Mini-ITX SBC
o
o
o
o
+V12S
+V1.35
+3.3A
+3.3V
5.3.3.1 Smart Fan Function
Use the Smart Fan Function submenu (BIOS Menu 7) to configure smart fan
temperature and speed settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Smart Fan Mode Configuration
CPU Smart Fan Control
Temperature of Off
Temperature if Start
Start PWM
Slope (Duty Cycle)
CPU Smart Fan control
settings.
[Auto PWM Mode]
75
80
30
[4]
--------------------: Select Screen
SYS Smart Fan Control
[Auto PWM Mode]
 : Select Item
Temperature of off
75
Enter Select
Temperature if Start
80
+ - Change Opt.
Start PWM
30
F1
General Help
Slope (Duty Cycle)
[4]
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 7: Smart Fan Function

CPU Smart Fan Control [Auto PWM Mode]
Use the CPU Smart Fan Control option to configure the CPU smart fan.

Manual
The fan spins at the speed set in Manual Mode
PWM
settings.
Mode

Auto
Mode

PWM
DEFAULT
The fan adjusts its speed using Auto Mode
settings.
SYS Smart Fan Control [Auto PWM Mode]
Use the SYS Smart Fan Control option to configure the system smart fan.
Page 90
KINO-ABT-i2 Mini-ITX SBC

Manual
The fan spins at the speed set in Manual Mode
PWM
settings.
Mode

Auto
PWM
Mode

DEFAULT
The fan adjusts its speed using Auto Mode
settings.
Temperature of Off
Use the + or – key to change the Temperature of Off value. Enter a decimal number
between 1 and 127.

Temperature of Start
Use the + or – key to change the Temperature of Start value. Enter a decimal number
between 1 and 127.

Start PWM
Use the + or – key to change the Start PWM value. Enter a decimal number between 1
and 100.

Slope (Duty Cycle)
Use the + or – key to change the Slope (Duty Cycle) value. Enter a decimal number
between 1 and 64.
Page 91
KINO-ABT-i2 Mini-ITX SBC
5.3.4 RTC Wake Settings
The RTC Wake Settings menu (BIOS Menu 8) configures RTC wake event. The RTC
wake function is supported in ACPI (S3/S4/S5) and APM soft off modes.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Wake System with Fixed Time
[Disabled]
Enables or Disables
system wake on alarm
event. When enabled,
system will wake on the
date: hr: min: sec
specified.
---------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 8: RTC Wake Settings

Wake System with Fixed Time [Disabled]
Use the Wake System with Fixed Time option to specify the time the system should be
roused from a suspended state.

Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event
Page 92
KINO-ABT-i2 Mini-ITX SBC

Enabled
If selected, the following appears with values that
can be selected:
*Wake up every day
*Wake up date
*Wake up hour
*Wake up minute
*Wake up second
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
5.3.5 Serial Port Console Redirection
The Serial Port Console Redirection menu (BIOS Menu 9) allows the console
redirection options to be configured. Console redirection allows users to maintain a
system remotely by re-directing keyboard input and text output through the serial port.
Page 93
KINO-ABT-i2 Mini-ITX SBC
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
COM1
Console Redirection
> Console Redirection Settings
[Disabled]
COM2
Console Redirection
> Console Redirection Settings
[Disabled]
COM3
Console Redirection
> Console Redirection Settings
[Disabled]
COM4
Console Redirection
> Console Redirection Settings
[Disabled]
COM5
Console Redirection
> Console Redirection Settings
[Disabled]
COM6
Console Redirection
> Console Redirection Settings
[Disabled]
IPMI (Disabled)
Console Redirection
Console Redirection
Enable or Disable
--------------------: Select Screen
 : Select Item
Enter Select
+/-: Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Port Is Disabled
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 9: Serial Port Console Redirection

Console Redirection [Disabled]
Use Console Redirection option to enable or disable the console redirection function.

Disabled

Enabled
DEFAULT
Disabled the console redirection function
Enabled the console redirection function
The following options are available in the Console Redirection Settings submenu when
the Console Redirection option is enabled.

Terminal Type [ANSI]
Use the Terminal Type option to specify the remote terminal type.
Page 94
KINO-ABT-i2 Mini-ITX SBC


VT100
The target terminal type is VT100

VT100+
The target terminal type is VT100+

VT-UTF8
The target terminal type is VT-UTF8

ANSI
DEFAULT
The target terminal type is ANSI
Bits per second [115200]
Use the Bits per second option to specify the serial port transmission speed. The speed
must match the other side. Long or noisy lines may require lower speeds.


9600
Sets the serial port transmission speed at 9600.

19200
Sets the serial port transmission speed at 19200.

38400
Sets the serial port transmission speed at 38400.

57600
Sets the serial port transmission speed at 57600.

115200
DEFAULT
Sets the serial port transmission speed at 115200.
Data Bits [8]
Use the Data Bits option to specify the number of data bits.


7

8
Sets the data bits at 7.
DEFAULT
Sets the data bits at 8.
Parity [None]
Use the Parity option to specify the parity bit that can be sent with the data bits for
detecting the transmission errors.

None

Even
DEFAULT
No parity bit is sent with the data bits.
The parity bit is 0 if the number of ones in the data
bits is even.

Odd
The parity bit is 0 if the number of ones in the data
bits is odd.
Page 95
KINO-ABT-i2 Mini-ITX SBC

The parity bit is always 1. This option does not
Mark
provide error detection.

The parity bit is always 0. This option does not
Space
provide error detection.

Stop Bits [1]
Use the Stop Bits option to specify the number of stop bits used to indicate the end of a
serial data packet. Communication with slow devices may require more than 1 stop bit.

1

2
DEFAULT
Sets the number of stop bits at 1.
Sets the number of stop bits at 2.
5.3.6 CPU Configuration
Use the CPU Configuration BIOS menu (BIOS Menu 10) to view detailed CPU
specifications and configure the CPU.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Celeron(R) CPU N2930 @ 1.83GHz
CPU Signature
30678
Microcode Patch
809
Max CPU Speed
1830 MHz
Min CPU Speed
500 MHz
Processor Cores
4
Intel HT Technology
Not Supported
Intel VT-x Technology
Supported
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
CPU Speed
64-bit
24 kB x 4
32 kB x 4
1024 kB x 2
Not Present
1834 MHz
Supported
Intel Virtualization Technology [Enabled]
EIST
[Enabled]
Number of cores to enable
in each processor
package.
---------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 10: CPU Configuration
Page 96
KINO-ABT-i2 Mini-ITX SBC
The CPU Configuration menu (BIOS Menu 10) lists the following CPU details:

CPU Signature: Lists the CPU signature value.

Microcode Patch: Lists the microcode patch being used.

Max CPU Speed: Lists the maximum CPU processing speed.

Min CPU Speed: Lists the minimum CPU processing speed.

Processor Cores: Lists the number of the processor core

Intel HT Technology: Indicates if Intel HT Technology is supported by the
CPU.

Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the
CPU.


L1 Data Cache: Lists the amount of data storage space on the L1 cache.

L1 Code Cache: Lists the amount of code storage space on the L1 cache.

L2 Cache: Lists the amount of storage space on the L2 cache.

L3 Cache: Lists the amount of storage space on the L3 cache.
Intel Virtualization Technology [Enabled]
Use the Intel Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel® Virtualization technology allows
several OSs to run on the same system at the same time.


Disabled

Enabled
Disables Intel Virtualization Technology.
DEFAULT
Enables Intel Virtualization Technology.
EIST [Enabled]
Use the EIST option to enable or disable Enhanced Intel SpeedStep® Techonology
(EIST).

Disables Enhanced Intel SpeedStep®
Disabled
Techonology.

Enabled
DEFAULT
Enables Enhanced Intel SpeedStep®
Techonology.
Page 97
KINO-ABT-i2 Mini-ITX SBC
5.3.7 IDE Configuration
Use the IDE Configuration menu (BIOS Menu 11) to change and/or set the configuration
of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
IDE Configuration
Select IDE / AHCI
SATA Mode
[IDE Mode]
Serial-ATA Port 1
SATA Port1 HotPlug
[Enabled]
[Disabled]
Serial-ATA Port 0
SATA Port0 HotPlug
[Enabled]
[Disabled]
---------------------
SATA Port1
Not Present
SATA Port0
Not Present
: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 11: IDE Configuration

SATA Mode Selection [IDE Mode]
Use the SATA Mode Selection option to configure SATA devices as normal IDE devices.


IDE Mode

AHCI Mode
DEFAULT
Configures SATA devices as normal IDE device.
Configures SATA devices as AHCI device.
Serial-ATA Port 1 [Enabled]
Use the Serial-ATA Port 1 option to enable or disable the serial ATA port 1.

Enabled

Disabled
Page 98
DEFAULT
Enables the SATA port 1.
Disables the SATA port 1.
KINO-ABT-i2 Mini-ITX SBC

SATA Port1 HotPlug [Disabled]
Use the SATA Port1 HotPlug option to enable or disable hotplug function of SATA port 1.


Enabled

Disabled
Enables SATA port 1 hotplug.
DEFAULT
Disables SATA port 1 hotplug.
Serial-ATA Port 0 [Enabled]
Use the Serial-ATA Port 0 option to enable or disable the serial ATA port 0.


Enabled

Disabled
DEFAULT
Enables the SATA port 0.
Disables the SATA port 0.
SATA Port0 HotPlug [Disabled]
Use the SATA Port0 HotPlug option to enable or disable hotplug function of SATA port 0.

Enabled

Disabled
Enables SATA port 0 hotplug.
DEFAULT
Disables SATA port 0 hotplug.
Page 99
KINO-ABT-i2 Mini-ITX SBC
5.3.8 Trusted Computing
Use the Trusted Computing menu (BIOS Menu 13) to configure settings related to the
Trusted Computing Group (TCG) Trusted Platform Module (TPM).
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Configuration
Security Device Support
[Disabled]
Current Status Information
No Security Device Found
Enables or Disables BIOS
support for security
device. O.S. will not
show Security Device.
TCG EFI protocol and
INT1A interface will not
be available.
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 12: Trusted Computing

Security Device Support [Disabled]
Use the Security Device Support option to configure support for the security device.

Disabled

Enabled
Page 100
DEFAULT
Security device is disabled
Security device is enabled
KINO-ABT-i2 Mini-ITX SBC
5.3.9 USB Configuration
Use the USB Configuration menu (BIOS Menu 13) to read USB configuration
information and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
1 Keyboard, 1 Mouse, 4 Hubs
Legacy USB Support
[Enabled]
Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 13: USB Configuration

USB Devices
The USB Devices Enabled field lists the USB devices that are enabled on the system

Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.

Enabled
DEFAULT
Legacy USB support enabled
Page 101
KINO-ABT-i2 Mini-ITX SBC

Disabled
Legacy USB support disabled

Auto
Legacy USB support disabled if no USB devices are
connected
5.4 Chipset
Use the Chipset menu (BIOS Menu 14) to access the North Bridge and South Bridge
subsystem configuration menus.
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
> North Bridge
> South Bridge
North Bridge Parameters.
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 14: Chipset
Page 102
KINO-ABT-i2 Mini-ITX SBC
5.4.1 North Bridge
Use the North Bridge menu (BIOS Menu 15) to configure the north bridge parameters.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
> Intel IGD Configuration
Memory Information
Total Memory
Memory Slot0
Memory Slot2
Intel IGD Configuration
4096 MB (LPDDR3)
4096 MB (LPDDR3)
Not Present
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 15: North Bridge
5.4.1.1 Intel IGD Configuration
Use the Intel IGD Configuration submenu (BIOS Menu 16) to configure the graphics
settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
Intel IGD Configuration
Primary Display
DVMT Pre-Allocated
DVMT Total Gfx Mem
[Auto]
[256M]
[Max]
Select which of IGD/PCI
Graphics device should
be Primary Display.
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
Primary IGFX Boot Display
[VBIOS Default]
BIOS Menu 16: Intel IGD Configuration
Page 103
KINO-ABT-i2 Mini-ITX SBC

Primary Display [Auto]
Use the Primary Display option to select which IGD/PCI graphics device will be the
primary display or to select SG for switchable Gfx. Configuration options are listed below.


Auto

IGD

PCI

SG
DEFAULT
DVMT Pre-Allocated [256M]
Use the DVMT Pre-Allocated option to specify the amount of system memory that can be
used by the internal graphics device.

64M
64 MB of memory used by internal graphics device

128M
128 MB of memory used by internal graphics
device

256M
DEFAULT
256 MB of memory used by internal graphics
device

512 MB of memory used by internal graphics
512M
device

DVMT Total Gfx Mem [Max]
Use the DVMT Total Gfx Mem option to specify the maximum amount of memory that can
be allocated as graphics memory. Configuration options are listed below.


128MB

256MB

Max
Default
Primary IGFX Boot Display [VBIOS Default]
Use the Primary IGFX Boot Display option to select the display device used by the
system when it boots. Configuration options are listed below.

Page 104
VBIOS Default
DEFAULT
KINO-ABT-i2 Mini-ITX SBC

CRT

DisplayPort

HDMI
5.4.2 South Bridge
Use the South Bridge menu (BIOS Menu 17) to configure the south bridge parameters.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
> Azalia HD Audio
> PCI Express Configuration
Azalia HD Audio Options
Auto Power Button Function
[Disabled (ATX)]
Restore AC Power Loss
[Last State]
Power Saving Function(EUP)
[Disabled]
USB SW1
USB SW2
[+5V DUAL]
[+5V DUAL]
XHCI Mode
[Smart Auto]
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 17: South Bridge

Restore on AC Power Loss [Last State]
Use the Restore on AC Power Loss BIOS option to specify what state the system
returns to if there is a sudden loss of power to the system.

Power Off
The system remains turned off

Power On
The system turns on

Last State
DEFAULT
The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.

Power Saving Function [Disabled]
Use the Power Saving Function BIOS option to enable or reduce power consumption in
the S5 state. When enabled, the system can only be powered-up using the power button.
Page 105
KINO-ABT-i2 Mini-ITX SBC


Enabled

Disabled
Power Saving Function support enabled
Power Saving Function support disabled
DEFAULT
USB SW1 [+5V DUAL]
Use the USB SW1 BIOS option to configure the USB power source for the corresponding
USB connector (Table 5-2).


+5V

+5V DUAL
Set the USB power source to +5V
DEFAULT
Set the USB power source to +5V dual
USB SW2 [+5V DUAL]
Use the USB SW2 BIOS option to configure the USB power source for the corresponding
USB connector (Table 5-2).

+5V

+5V DUAL
BIOS Options
USB SW1
USB SW2
Set the USB power source to +5V
DEFAULT
Set the USB power source to +5V dual
Configured USB Ports
LAN1_USB1 (external USB 3.0 ports)
LAN2_USB2 (external USB 2.0 ports)
USB1, USB2 (internal USB 2.0 ports)
Table 5-2: BIOS Options and Configured USB Ports

XHCI Mode [Smart Auto]
Use the XHCI Mode BIOS option to configure the USB xHCI (USB 3.0) controller.

Enable the xHCI controller. USB 3.0 ports behave as
Enabled
USB 3.0 ports.

Smart
Auto
DEFAULT
Allow the use of USB 3.0 devices prior to OS boot.
USB 3.0 ports function as USB 3.0 ports even during a
reboot.
Page 106
KINO-ABT-i2 Mini-ITX SBC
5.4.2.1 Azalia HD Audio
Use the Azalia HD Audio submenu (BIOS Menu 18) to configure the High Definition
Audio codec.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
Audio Configuration
Audio Controller
[Enabled]
Control Detection of the
Azalia device.
Disabled=Azalia will be
unconditionally
disabled.
Enabled=Azalia will be
unconditionally
Enabled.
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 18: Azalia HD Audio

Audio Controller [Enabled]
Use the Audio Controller BIOS option to enable or disable the High Definition Audio
controller.

Disabled

Enabled
The High Definition Audio controller is disabled.
DEFAULT
The High Definition Audio controller is enabled.
Page 107
KINO-ABT-i2 Mini-ITX SBC
5.4.2.2 PCI Express Configuration
Use the PCI Express Configuration submenu (BIOS Menu 19) to configure the PCI
Express slots.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
PCI Express Configuration
PCI Express Port 0
Speed
[Enabled]
[Auto]
PCI Express Port 1
Speed
[Enabled]
[Auto]
Enable or Disable the PCI
Express Port 0 in the
Chipset.
--------------------: Select Screen
PCI Express Port 2
[Enabled]
 : Select Item
Speed
[Auto]
Enter Select
+ - Change Opt.
PCI Express Port 3
[Enabled]
F1
General Help
Speed
[Auto]
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 19: PCI Express Configuration

PCI Express Port n [Enabled]
Use the PCI Express Port n option to enable or disable the corresponding PCIe slot.


Enabled

Disabled
DEFAULT
The PCIe slot is enabled.
The PCIe slot is disabled.
Speed [Auto]
Use the Speed option to configure the speed of the corresponding PCIe slot.
Page 108

Auto

Gen 2

Gen 1
DEFAULT
KINO-ABT-i2 Mini-ITX SBC
5.5 Security
Use the Security menu (BIOS Menu 20) to set system and user passwords.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Password Description
If ONLY the Administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup.
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password must be
In the following range:
Maximum length
3
Minimum length
20
Set Administrator
Password
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Administrator Password
User Password
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 20: Security

Administrator Password
Use the Administrator Password to set or change a administrator password.

User Password
Use the User Password to set or change a user password.
Page 109
KINO-ABT-i2 Mini-ITX SBC
5.6 Boot
Use the Boot menu (BIOS Menu 21) to configure system boot options.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Boot Configuration
Bootup NumLock State
Quiet Boot
Option ROM Messages
UEFI Boot
Launch PXE OpROM
[On]
[Enabled]
[Force BIOS]
[Disabled]
[Disabled]
Select the keyboard
NumLock state
--------------------: Select Screen
 : Select Item
Enter Select
Boot Option Priorities
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 21: Boot

Bootup NumLock State [On]
Use the Bootup NumLock State BIOS option to specify if the number lock setting must
be modified during boot up.

On
DEFAULT
Allows the Number Lock on the keyboard to be
enabled automatically when the computer system
boots up. This allows the immediate use of the
10-key numeric keypad located on the right side of
the keyboard. To confirm this, the Number Lock LED
light on the keyboard is lit.

Off
Does not enable the keyboard Number Lock
automatically. To use the 10-keys on the keyboard,
press the Number Lock key located on the upper
left-hand corner of the 10-key pad. The Number
Lock LED on the keyboard lights up when the
Number Lock is engaged.
Page 110
KINO-ABT-i2 Mini-ITX SBC

Quiet Boot [Enabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.


Disabled

Enabled
Normal POST messages displayed
DEFAULT
OEM Logo displayed instead of POST messages
Option ROM Messages [Force BIOS]
Use the Option ROM Messages option to set the Option ROM display mode.

Force
DEFAULT
Sets display mode to force BIOS.
BIOS

Sets display mode to current.
Keep
Current

UEFI Boot [Disabled]
Use the UEFI Boot option to enable or disable to boot from a UEFI device.


Enabled

Disabled
Enable to boot from a UEFI device.
DEFAULT
Disable to boot from a UEFI device.
Launch PXE OpROM [Disabled]
Use the Launch PXE OpROM option to enable or disable boot option for legacy network
devices.

Disabled

Enabled
DEFAULT
Ignore all PXE Option ROMs
Load PXE Option ROMs
Page 111
KINO-ABT-i2 Mini-ITX SBC
5.7 Exit
Use the Exit menu (BIOS Menu 22) to load default BIOS values, optimal failsafe values
and to save configuration changes.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Save Changes and Reset
Discard Changes and Reset
Exit the system after
saving the changes.
Restore Defaults
Save as User Defaults
Restore User Defaults
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 22:Exit

Save Changes and Reset
Use the Save Changes and Reset option to save the changes made to the BIOS options
and reset the system.

Discard Changes and Reset
Use the Discard Changes and Reset option to exit the system without saving the
changes made to the BIOS configuration setup program.

Restore Defaults
Use the Restore Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F3 key can be used for this operation.
Page 112
KINO-ABT-i2 Mini-ITX SBC

Save as User Defaults
Use the Save as User Defaults option to save the changes done so far as user defaults.

Restore User Defaults
Use the Restore User Defaults option to restore the user defaults to all the setup options.
Page 113
KINO-ABT-i2 Mini-ITX SBC
Chapter
6
6 Software Drivers
Page 114
KINO-ABT-i2 Mini-ITX SBC
6.1 Available Software Drivers
NOTE:
The content of the CD may vary throughout the life cycle of the product
and is subject to change without prior notice. Visit the IEI website or
contact technical support for the latest updates.
The following drivers can be installed on the system:

Chipset

Graphics

LAN
Installation instructions are given below.
6.2 Software Installation
All the drivers for the KINO-ABT-i2 are on the CD that came with the system. To install the
drivers, please follow the steps below.
Step 1: Insert the CD into a CD drive connected to the system.
NOTE:
If the installation program doesn't start automatically:
Click "Start->My Computer->CD Drive->autorun.exe"
Step 2: The driver main menu appears (Figure 6-1).
Step 3: Click NANO-BT-i1.
Page 115
KINO-ABT-i2 Mini-ITX SBC
Figure 6-1: Driver CD Main Menu
Step 4: A new screen with a list of available drivers appears (Figure 6-2).
Figure 6-2: Available Drivers
Page 116
KINO-ABT-i2 Mini-ITX SBC
Step 5: Install all of the necessary drivers in the menu.
6.3 Chipset Driver Installation
To install the chipset driver, please do the following.
Step 1: Access the driver list. (See Section 6.2)
Step 2: Click “1-Bay Trail SOC” and select the folder which corresponds to the
operating system.
NOTE:
The remainder of this installation assumes Windows 8 as the operating
system.
Step 3: Locate the setup file (infinst_autol_9.4.4.1006.exe) and double click on it.
Step 4: When the setup files are completely extracted, the Welcome Screen in Figure
6-3 appears. Click Next to continue.
Figure 6-3: Chipset Driver Welcome Screen
Page 117
KINO-ABT-i2 Mini-ITX SBC
Step 5: The License Agreement in Figure 6-4 appears.
Step 6: Click Yes to accept the agreement and continue.
Figure 6-4: Chipset Driver License Agreement
Step 7: The Read Me file in Figure 6-5 appears.
Step 8: Click Next to continue.
Figure 6-5: Chipset Driver Read Me File
Page 118
KINO-ABT-i2 Mini-ITX SBC
Step 9: Setup Operations are performed as shown in Figure 6-6.
Step 10: Once the Setup Operations are complete, click Next to continue.
Figure 6-6: Chipset Driver Setup Operations
Step 11: The Finish screen in Figure 6-7 appears.
Step 12: Select “Yes, I want to restart this computer now” and click Finish. Step 0:
Figure 6-7: Chipset Driver Installation Finish Screen
Page 119
KINO-ABT-i2 Mini-ITX SBC
6.4 Graphics Driver Installation
To install the Graphics driver, please do the following.
Step 1: Access the driver list. (See Section 6.2)
Step 2: Click “1-Bay Trail SOC” and select the folder which corresponds to the
operating system.
NOTE:
The remainder of this installation assumes Windows 8 as the operating
system.
Step 3: Unzip the file called 15.33.7.3366.zip, and then locate the setup file and double
click on it to start the installation. If a 64-bit operating system is installed, please
unzip the 15.33.7.64.336.zip file to install the graphics driver.
NOTE:
To install graphics driver on a 32-bit Windows 7 system, unzip
INTEL_EMGD.WIN7_PC_VERSION_36_15_0_1064.7Z.
To install graphics driver on a 64-bit Windows 7 system, unzip
INTEL_EMGD.WIN7_BETA_VERSION_37_15_0_1055.7Z.
Step 4: The Welcome Screen in Figure 6-8 appears.
Step 5: Click Next to continue.
Page 120
KINO-ABT-i2 Mini-ITX SBC
Figure 6-8: Graphics Driver Welcome Screen
Step 6: The License Agreement in Figure 6-9 appears.
Step 7: Click Yes to accept the agreement and continue.
Figure 6-9: Graphics Driver License Agreement
Step 8: The Read Me file in Figure 6-10 appears. Click Next to continue.
Page 121
KINO-ABT-i2 Mini-ITX SBC
Figure 6-10: Graphics Driver Read Me File
Step 9: Setup Operations are performed as shown in Figure 6-11.
Step 10: Once the Setup Operations are complete, click Next to continue.
Figure 6-11: Graphics Driver Setup Operations
Step 11: The system starts installing the Graphics Driver.
Step 12: The Finish screen in Figure 6-12 appears.
Page 122
KINO-ABT-i2 Mini-ITX SBC
Step 13: Select “Yes, I want to restart this computer now” and click Finish. Step 0:
Figure 6-12: Graphics Driver Installation Finish Screen
6.5 LAN Driver Installation
To install the LAN driver, please do the following.
Step 1: Right-click This PC icon on the desktop and select Properties. (Figure 6-13).
Page 123
KINO-ABT-i2 Mini-ITX SBC
Figure 6-13: PC Properties
Step 2: The system control panel window in Figure 6-14 appears.
Step 3: Click the Device Manager link (Figure 6-14).
Figure 6-14: System Control Panel
Page 124
KINO-ABT-i2 Mini-ITX SBC
Step 4: A list of system hardware devices appears (Figure 6-15).
Step 5: Right-click one of the Ethernet controllers that has question marks next to it (this
means Windows does not recognize the device).
Step 6: Select Update Driver Software. See Figure 6-15.
Figure 6-15: Device Manager List
Step 7: The Update Driver Software Window appears (Figure 6-16).
Page 125
KINO-ABT-i2 Mini-ITX SBC
Figure 6-16: Update Driver Software Window
Step 8: Select “Browse my computer for driver software” and click NEXT to continue.
Step 9: Click Browse to select “X:\2-LAN\Intel” directory in the Locate File window,
where “X:\” is the system CD drive. (Figure 6-17).
Figure 6-17: Locate Driver Files
Step 10: Click NEXT to continue.
Page 126
KINO-ABT-i2 Mini-ITX SBC
Step 11: Driver Installation is performed. When the Finish screen appears, click Close to
exit.
Step 12: Right-click the other Ethernet controller that has question marks next to it as
shown in Figure 6-15. Repeat Step 6–Step 11 to install the second Ethernet
controller driver. Step 0:
Page 127
KINO-ABT-i2 Mini-ITX SBC
Appendix
A
A BIOS Options
Page 128
KINO-ABT-i2 Mini-ITX SBC
Below is a list of BIOS configuration options in the BIOS chapter.
BIOS Information .................................................................................................................76
Memory Information ............................................................................................................77
TXE Information ...................................................................................................................77
System Date [xx/xx/xx] ........................................................................................................77
System Time [xx:xx:xx] .......................................................................................................77
ACPI Sleep State [S3 (Suspend to RAM)]..........................................................................79
Serial Port [Enabled]............................................................................................................81
Change Settings [Auto] .......................................................................................................81
Serial Port [Enabled]............................................................................................................82
Change Settings [Auto] .......................................................................................................82
Serial Port [Enabled]............................................................................................................83
Change Settings [Auto] .......................................................................................................83
Serial Port [Enabled]............................................................................................................84
Change Settings [Auto] .......................................................................................................84
Serial Port [Enabled]............................................................................................................85
Change Settings [Auto] .......................................................................................................86
Serial Port [Enabled]............................................................................................................87
Change Settings [Auto] .......................................................................................................87
Smart Fan Function .............................................................................................................89
PC Health Status ..................................................................................................................89
CPU Smart Fan Control [Auto PWM Mode] .......................................................................90
SYS Smart Fan Control [Auto PWM Mode] .......................................................................90
Temperature of Off...............................................................................................................91
Temperature of Start............................................................................................................91
Start PWM .............................................................................................................................91
Slope (Duty Cycle) ...............................................................................................................91
Wake System with Fixed Time [Disabled] .........................................................................92
Console Redirection [Disabled] .........................................................................................94
Terminal Type [ANSI]...........................................................................................................94
Bits per second [115200].....................................................................................................95
Data Bits [8] ..........................................................................................................................95
Parity [None].........................................................................................................................95
Stop Bits [1] ..........................................................................................................................96
Page 129
KINO-ABT-i2 Mini-ITX SBC
Intel Virtualization Technology [Enabled] .........................................................................97
EIST [Enabled]......................................................................................................................97
SATA Mode Selection [IDE Mode] ......................................................................................98
Serial-ATA Port 1 [Enabled] ................................................................................................98
SATA Port1 HotPlug [Disabled]..........................................................................................99
Serial-ATA Port 0 [Enabled] ................................................................................................99
SATA Port0 HotPlug [Disabled]..........................................................................................99
Security Device Support [Disabled]................................................................................ 100
USB Devices ...................................................................................................................... 101
Legacy USB Support [Enabled]....................................................................................... 101
Primary Display [Auto] ..................................................................................................... 104
DVMT Pre-Allocated [256M] ............................................................................................. 104
DVMT Total Gfx Mem [Max].............................................................................................. 104
Primary IGFX Boot Display [VBIOS Default] .................................................................. 104
Restore on AC Power Loss [Last State] ......................................................................... 105
Power Saving Function [Disabled].................................................................................. 105
USB SW1 [+5V DUAL]....................................................................................................... 106
USB SW2 [+5V DUAL]....................................................................................................... 106
XHCI Mode [Smart Auto] .................................................................................................. 106
Audio Controller [Enabled] .............................................................................................. 107
PCI Express Port n [Enabled] .......................................................................................... 108
Speed [Auto]...................................................................................................................... 108
Administrator Password .................................................................................................. 109
User Password .................................................................................................................. 109
Bootup NumLock State [On]............................................................................................ 110
Quiet Boot [Enabled] ........................................................................................................ 111
Option ROM Messages [Force BIOS].............................................................................. 111
UEFI Boot [Disabled] ........................................................................................................ 111
Launch PXE OpROM [Disabled] ...................................................................................... 111
Save Changes and Reset ................................................................................................. 112
Discard Changes and Reset ............................................................................................ 112
Restore Defaults ............................................................................................................... 112
Save as User Defaults ...................................................................................................... 113
Restore User Defaults ...................................................................................................... 113
Page 130
KINO-ABT-i2 Mini-ITX SBC
Appendix
B
B Terminology
Page 131
KINO-ABT-i2 Mini-ITX SBC
AC ’97
Audio Codec 97 (AC’97) refers to a codec standard developed by Intel®
in 1997.
ACPI
Advanced Configuration and Power Interface (ACPI) is an OS-directed
configuration, power management, and thermal management interface.
AHCI
Advanced Host Controller Interface (AHCI) is a SATA Host controller
register-level interface.
ATA
The Advanced Technology Attachment (ATA) interface connects storage
devices including hard disks and CD-ROM drives to a computer.
ARMD
An ATAPI Removable Media Device (ARMD) is any ATAPI device that
supports removable media, besides CD and DVD drives.
ASKIR
Amplitude Shift Keyed Infrared (ASKIR) is a form of modulation that
represents a digital signal by varying the amplitude (“volume”) of the
signal. A low amplitude signal represents a binary 0, while a high
amplitude signal represents a binary 1.
BIOS
The Basic Input/Output System (BIOS) is firmware that is first run when
the computer is turned on and can be configured by the end user
CODEC
The Compressor-Decompressor (CODEC) encodes and decodes digital
audio data on the system.
CMOS
Complimentary metal-oxide-conductor is an integrated circuit used in
chips like static RAM and microprocessors.
COM
COM refers to serial ports. Serial ports offer serial communication to
expansion devices. The serial port on a personal computer is usually a
male D-sub 9 connector.
DAC
The Digital-to-Analog Converter (DAC) converts digital signals to analog
signals.
DDR
Double Data Rate refers to a data bus transferring data on both the rising
and falling edges of the clock signal.
DMA
Direct Memory Access (DMA) enables some peripheral devices to
bypass the system processor and communicate directly with the system
memory.
Page 132
KINO-ABT-i2 Mini-ITX SBC
DIMM
Dual Inline Memory Modules are a type of RAM that offer a 64-bit data
bus and have separate electrical contacts on each side of the module.
DIO
The digital inputs and digital outputs are general control signals that
control the on/off circuit of external devices or TTL devices. Data can be
read or written to the selected address to enable the DIO functions.
EHCI
The Enhanced Host Controller Interface (EHCI) specification is a
register-level interface description for USB 2.0 Host Controllers.
EIDE
Enhanced IDE (EIDE) is a newer IDE interface standard that has data
transfer rates between 4.0 MBps and 16.6 MBps.
EIST
Enhanced Intel® SpeedStep Technology (EIST) allows users to modify
the power consumption levels and processor performance through
application software. The application software changes the bus-to-core
frequency ratio and the processor core voltage.
FSB
The Front Side Bus (FSB) is the bi-directional communication channel
between the processor and the Northbridge chipset.
GbE
Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0
Gbps and complies with the IEEE 802.3-2005 standard.
GPIO
General purpose input
HDD
Hard disk drive (HDD) is a type of magnetic, non-volatile computer
storage device that stores digitally encoded data.
ICH
The Input/Output Control Hub (ICH) is an Intel® Southbridge chipset.
IrDA
Infrared Data Association (IrDA) specify infrared data transmission
protocols used to enable electronic devices to wirelessly communicate
with each other.
L1 Cache
The Level 1 Cache (L1 Cache) is a small memory cache built into the
system processor.
L2 Cache
The Level 2 Cache (L2 Cache) is an external processor memory cache.
LCD
Liquid crystal display (LCD) is a flat, low-power display device that
consists of two polarizing plates with a liquid crystal panel in between.
Page 133
KINO-ABT-i2 Mini-ITX SBC
LVDS
Low-voltage differential signaling (LVDS) is a dual-wire, high-speed
differential electrical signaling system commonly used to connect LCD
displays to a computer.
POST
The Power-on Self Test (POST) is the pre-boot actions the system
performs when the system is turned-on.
RAM
Random Access Memory (RAM) is volatile memory that loses data when
power is lost. RAM has very fast data transfer rates compared to other
storage like hard drives.
SATA
Serial ATA (SATA) is a serial communications bus designed for data
transfers between storage devices and the computer chipsets. The SATA
bus has transfer speeds up to 1.5 Gbps and the SATA II bus has data
transfer speeds of up to 3.0 Gbps.
S.M.A.R.T
Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers to
automatic status checking technology implemented on hard disk drives.
UART
Universal Asynchronous Receiver-transmitter (UART) is responsible for
asynchronous communications on the system and manages the system’s
serial communication (COM) ports.
UHCI
The Universal Host Controller Interface (UHCI) specification is a
register-level interface description for USB 1.1 Host Controllers.
USB
The Universal Serial Bus (USB) is an external bus standard for
interfacing devices. USB 1.1 supports 12Mbps data transfer rates and
USB 2.0 supports 480Mbps data transfer rates.
VGA
The Video Graphics Array (VGA) is a graphics display system developed
by IBM.
Page 134
KINO-ABT-i2 Mini-ITX SBC
Appendix
C
C Watchdog Timer
Page 135
KINO-ABT-i2 Mini-ITX SBC
NOTE:
The following discussion applies to DOS environment. Contact IEI support
or visit the IEI website for specific drivers for other operating systems.
The Watchdog Timer is provided to ensure that standalone systems can always recover
from catastrophic conditions that cause the CPU to crash. This condition may have
occurred by external EMIs or a software bug. When the CPU stops working correctly,
Watchdog Timer either performs a hardware reset (cold boot) or a Non-Maskable Interrupt
(NMI) to bring the system back to a known state.
A BIOS function call (INT 15H) is used to control the Watchdog Timer.
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table C-1: AH-6FH Sub-function
Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value
is not zero, the Watchdog Timer starts counting down. When the timer value reaches zero,
the system resets. To ensure that this reset condition does not occur, calling sub-function
2 must periodically refresh the Watchdog Timer. However, the watchdog timer is disabled
if the time-out value is set to zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 136
KINO-ABT-i2 Mini-ITX SBC
NOTE:
When exiting a program it is necessary to disable the Watchdog Timer,
otherwise the system resets.
EXAMPLE PROGRAM:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
;
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD THE APPLICATION PROGRAM HERE
;
CMP
JNE
EXIT_AP, 1
W_LOOP
MOV
AX, 6F02H
MOV
BL, 0
INT
;is the application over?
;No, restart the application
;disable Watchdog Timer
;
15H
;
; EXIT ;
Page 137
KINO-ABT-i2 Mini-ITX SBC
Appendix
D
D Hazardous Materials
Disclosure
Page 138
KINO-ABT-i2 Mini-ITX SBC
D.1 Hazardous Materials Disclosure Table for IPB Products
Certified as RoHS Compliant Under 2002/95/EC Without
Mercury
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
Page 139
KINO-ABT-i2 Mini-ITX SBC
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl
(CR(VI))
(PBB)
Ethers
(PBDE)
Housing
O
O
O
O
O
O
Display
O
O
O
O
O
O
Printed Circuit
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Fan Assembly
O
O
O
O
O
O
Power Supply
O
O
O
O
O
O
O
O
O
O
O
O
Board
Metal
Fasteners
Cable
Assembly
Assemblies
Battery
O:
This toxic or hazardous substance is contained in all of the homogeneous materials for the part is
below the limit requirement in SJ/T11363-2006
X:
This toxic or hazardous substance is contained in at least one of the homogeneous materials for
this part is above the limit requirement in SJ/T11363-2006
Page 140
KINO-ABT-i2 Mini-ITX SBC
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些元
件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
醚
(PBDE)
壳体
O
O
O
O
O
O
显示
O
O
O
O
O
O
印刷电路板
O
O
O
O
O
O
金属螺帽
O
O
O
O
O
O
电缆组装
O
O
O
O
O
O
风扇组装
O
O
O
O
O
O
电力供应组装
O
O
O
O
O
O
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
Page 141
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement