Jablotron Oasis 80 JA-80N RFID card reader User manual
Below you will find brief information for RFID card reader JA-80N. The JA-80N is a component of Jablotron’s Oasis 80 alarm system and is designed to control access (door lock) or to control a security system. This device can be connected to the Oasis control panel via a WJ-80 interface or alternatively it can be connected to an AS-80 unit as a part of a stand-alone access system. The JA-80N is designed for outdoor use and features an RFID card reader.
advertisement
The JA-80N outdoor RFID card reader
The JA-80N is a component of Jablotron’s Oasis
80 alarm system. It is designed to control access
(door lock) or to control a security system and connects to the Oasis control panel via a WJ-80 interface.
Alternatively it can be connected to an AS-80 unit as a part of a stand-alone access system.
9. Disconnect the power from the control panel, connect the yellow and brown wires back up, power-up the control panel and check the proper functioning of the JA-80H keypad
Note: The red LED is lit in normal operating mode. Using a card is confirmed by a flash from the orange LED.
How to set up the JA-80N reader for the AS-80 access system is described in the AS-80 manual.
Technical specifications
The keypad sends data in Wiegand 26b format.
Installation
Installation shall only be undertaken by technicians holding a certificate issued by an authorized distributor. It is usually placed near an entrance door
(equipped with an electronic lock). The reader can be used outdoors (conforms to IP-65).
1. Open the rear cover by unscrewing the screw
2. Prepare a hole in the wall for the reader cable to pass through, where the reader will be located.
3. Attach the rear cover to the desired location (the tamper spring must be properly pressed)
4. Pull the reader cable through the wall hole and to the interface unit’s box (WJ-80, AS-80)
5. Attach the reader to the rear cover and secure it using the screw
6. Connecting and setting up the reader is described in the WJ-80 or AS-80 manuals.
Cabling
wire signal red +12V (power supply, 60mA)
green brown
D0 (Wiegand 26b data output)
D1 (Wiegand 26b data output)
white grey yellow
blue
TMP (normally closed tamper contact)
TMP (normally closed tamper contact)
BZR (input controlling reader’s sound – connecting to GND generates a beep on the reader)
GND (common ground)
Power supply
Stand-by consumption
Enclosure protection (EN 60529)
Mechanical endurance (EN 50102)
10 to 16V DC typically 60mA
IP65
IK08
Environmental (EN 50131-1)
Operational temperature range class IV – outdoor general
-25 to +60°C
RFID card Jablotron PC-01 or PC-02 (EM UNIQUE 125 kHz)
Dimensions
Length of the connection cable
46 x 150.5 x 22.5mm
1m
Complies with grade 2 (EN 50131-1, TS 50131-3)
Jablotron Ltd. hereby declares that the JA-80N is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The original of the conformity assessment can be found at www.jablotron.com
,
Technical Support section
Note: Although this product does not contain any harmful materials we suggest you return the product to the dealer or directly to the producer after use. cca 1 m
Configuring the reader for operation with the WJ-80
If the JA-80N reader is connected to an Oasis control panel and it does not work as described in the manual, then it is not set to the correct
(factory default) operational mode. In such a case:
1. Switch the Oasis control panel to service mode
2. Disconnect the power from the control panel (mains and battery)
3. Get an RFID card ready (PC-01 or PC-02)
4. Disconnect the yellow and brown wires from the WJ-80 interface terminals and connect the wires together
5. Power-up the control panel (reader starts beeping)
6. Disconnect the yellow and brown wires from each other (beeping will terminate)
7. Use the RFID card 4 times (put it close to the reader and after a short beep take it away) – then wait a moment until a few beeps sound (by this procedure you enter “4” without pressing a key, as there are no keys to press)
8. Now use the RFID card 3 times (put it close to the reader and after a short beep take it away) – then wait a moment until a few beeps sound (by this procedure you enter “3” without pressing a key, as there are no keys to press)
45 22,5
TAMPER
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic
Tel.: +420 483 559 999 fax: +420 483 559 993
Internet: www.jablotron.cz
MKM51400_OS1 The JA-80N outdoor RFID card reader
1
advertisement
Key Features
- Outdoor RFID card reader
- Control access (door lock)
- Control security system
- Connects to Oasis control panel
- Connects to AS-80 unit
- IP65 protection
- Wiegand 26b format
- Jablotron PC-01 or PC-02 cards
- 10 to 16V DC power supply
- Tamper contact
Frequently Answers and Questions
How to set up the JA-80N reader for the AS-80 access system?
What type of RFID card is compatible with the JA-80N?
How do I configure the JA-80N reader for operation with the WJ-80 interface?
Related manuals
advertisement