Low Differential Pressure Switches for General Industrial Service Series 1800

Low Differential Pressure Switches for General Industrial Service Series 1800
E-53(english)
7/2/03
4:15 PM
Page 1
Bulletin E-53
Series Low Differential Pressure Switches
1800 for General Industrial Service
Specifications — Installation and Operating Instructions
1-27/32
[46.83]
fl7/8 [22.23]
CONDUIT
CONNECTION
3-39/64
[91.68]
3-1/8
[79.38]
fl4
[101.60]
Model 1823 pressure switch. UL
and CSA Listed, FM and CENELEC
approved.
Series 1823 pressure switch.
Conduit enclosure removed to
show electric switch.
One of our most popular pressure switches. Combines small
size and low price with 2% repeatability for enough accuracy for
all but the most demanding applications. Set point adjustment
inside the mounting switch on one side of a wall or panel with
adjustment easily accessible on the opposite side.
1-1/8
[28.57]
1/8 FEMALE NPT
HIGH PRESSURE
CONNECTION
1/2 MALE NPT
MOUNTING SPUD
3/4
[19.05]
1/8 FEMALE NPT
LOW PRESSURE
CONNECTION
2-3/32
[53.18]
2-1/8
3-27/32
[53.98]
[97.63]
CLEARANCE FOR
COVER REMOVAL
Construction and dimensions. Series 1823 pressure switches.
SPECIFICATIONS
Service: Air and non-combustible, compatible gases.
Wetted Materials: Consult Factory.
Temperature Limits: -30 to 180°F (-34 to 82.2°C). 1823-00,
*Model 1823 shown; (1823 replaces 1820, 1821 and 1822
which are similar).
-20 to 180°F (-28.9 to 82.2°C).
Pressure Limits: 10 psig (68.95 kPa) continuous, 25 psig
Environmental (MIL) Switch
(172.4 kPa) surge.
Unlisted Model 1820 can be furnished with special snap switch
sealed against the environment for high humidity and/or for
government applications. Similar to standard Model 1823 except
dead band is slightly greater. Specify Model 1820 (Range No.)
"MIL" in ordering.
Switch Type: Single-pole double-throw (SPDT).
Repeatability: ±2%.
Electrical Rating: 15 A @ 120-480 VAC, 60 Hz. Resistive 1/8
HP @125 VAC, 1/4 HP @ 250 VAC, 60 Hz. De-rate to 10 A for
SERIES 1823 SWITCHES —
OPERATING RANGES & DEADBANDS
operation at high cycle rates.
Approximate
Dead Band
Electrical Connections: 3 screw type, common, normally open
Model
Number
Operating
Range,
Inches W.C.
At Min.
Set Point
At Max.
Set Point
1823-00
1823-0
1823-1
1823-2
1823-5
1823-10
1823-20
1823-40
1823-80
0.07 to 0.22
0.15 to 0.5
0.3 to 1.0
0.5 to 2.0
1.5 to 5.0
2.0 to10
3 to 22
5 to 44
9 to 85
0.05
0.06
0.08
0.10
0.14
0.18
0.35
0.56
1.30
0.05
0.06
0.08
0.12
0.28
0.45
0.70
1.10
3.0
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A.
and normally closed.
Process Connections: 1/8˝ female NPT.
Mounting Orientation: Diaphragm in vertical position. Consult
factory for other position orientations.
Set Point Adjustment: Screw type inside mounting spud.
Weight: 1 lb, 5 oz (595 g).
Agency Approvals: CE, UL, CSA, FM.
Phone: 219/879-8000
Fax: 219/872-9057
www.dwyer-inst.com
e-mail: [email protected]
E-53(english)
7/2/03
4:15 PM
Page 2
INSTALLATION
ADJUSTMENT
1. If the switch has been factory preset, check the set-point before
placing in service to assure it has not shifted in transit.
2. If switching has not been preset or it is desired to change the
point, observe the following procedure:
a. To adjust the set point turn the slotted Adjustment Screw
clockwise to increase the set point and counterclockwise to
decrease the set point.
b. The following is a recommended procedure for calibrating or
checking calibration: Use a "T" assembly with three rubber
tubing leads, all as short as possible and the entire assembly
offering minimum flow restriction. Run one lead to the
pressure switch, another to a manometer of known accuracy
and appropriate range, and apply pressure through the third
tube. Make final approach to the set point slowly. Note the
manometer and pressure switch will have different response
characteristics due to different internal volumes, lengths of
tubing, oil drainage, etc. Be certain switch is checked in
position it will assume in use, i.e. vertical, horizontal, etc.
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A.
1-1/2 [38.10]
1-1/4 [31.75]
3/32 [2.38]
1/8 FEMALE NPT
LOW PRESSURE
CONNECTION
1/2 FEMALE NPT
CONDUIT
CONNECTION
N.C.
COM .
6 [15.40] 4 [101.60]
SQ
TYP
N.O.
1. Select a location free form excessive vibration and where oil or
water will not drip upon the switch. See special housings for
unusual conditions.
2. While not required, positioning the pressure connections
down is recommended. Mount the switch with the diaphragm
in a vertical plane. Switch with the diaphragm in a vertical plane.
Switch must be recalibrated for each change in operating
position.
3. Connect switch to source of pressure differential. Metal tubing
with 1/4" O.D. is recommended but any tubing system which
will not restrict the air flow is satisfactory. Note that the low
pressure connection may be made to the 1/2" spud at the back
of the switch if desired. If so connected, drill 1/16" diameter
holes in the Spring Retainer flange and the head of Adjustment
Screw to provide opening to the switch interior and plug the
other low pressure connection.
4. Electrical connections to the standard single pole, double throw
snap switch are provided by means of screw terminals marked
"common", "norm open", and "norm closed". The normally
open contacts close and the normally closed contact open
when pressure increases beyond the set point.
5. Switch loads should not exceed the maximum specified current
rating of 15 amps resistive. Switch capabilities decrease with
high load inductance or rapid cycle rates. whenever and
application involves one or more of these factors, the user may
find it desirable to limit the switched current to 10 amps or less
in the interest of prolonged switch life.
3
[76.20]
6-3/4
[171.45] TYP
7-1/2
[190.50]
Ø5/16 [7.94]
MOUNTING
HOLES
TYP 4 PLACES
3/4 [19.05]
CLEARANCE FOR
COVER REMOVAL
1-1/2 [38.10] TYP
1/8 FEMALE NPT HIGH
PRESSURE CONNECTION
4-1/6
[103.19]
1-7/16
[36.53]
Weatherproof Enclosure
16 ga. steel enclosure for unusually wet or oily conditions.
Withstands 200 hour salt spray test. Gasketed cover. Weight 5-1/2
lb (2.5 kg). Switch must be installed at factory. Specify "WP" in
addition to switch catalog number.
1/8 FEMALE NPT
HIGH PRESSURE
CONNECTION
Ø5/16 [7.94]
TYP 4 PLACES
1/2 FEMALE NPT
COUNDUIT
CONNECTION
5-7/8
4-1/4
6-3/8 [149.23]
[107.95]
[161.93] TYP
TYP
4-1/4
[107.95] TYP
1/8 FEMALE NPT
LOW PRESSURE
CONNECTION
7/16
[11.11]
3-3/4
[95.25]
CLEARANCE
FOR COVER
REMOVAL
1-1/16
[26.99]
2-3/4
[70.61]
6-15/16
[176.21]
Explosion-Proof Housing
Cast iron base and aluminum dome cover. Approximate weight 71/2 lb (3.4 kg). Specify "EXPL" in addition to switch catalog
number.
Phone: 219/879-8000
www.dwyer-inst.com
Fax: 219/872-9057 e-mail: [email protected]
E-53(spanish)
7/2/03
4:19 PM
Page 1
Bulletin E-53
SERIE
1800
Interruptor Para Baja
Presión Diferencial
1-27/32
[46.83]
fl7/8 [22.23]
CONDUIT
CONNECTION
3-39/64
[91.68]
3-1/8
[79.38]
fl4
[101.60]
Model 1823 pressure switch. UL
and CSA Listed, FM approved.
Series 1823 pressure switch.
Conduit enclosure removed to
show electric switch.
Uno de nuestros mas populares interruptores de presión.
Combina un pequeño tamaño y bajo precio, con una repetibilidad
del 2%, exactitud suficiente para las aplicaciones con mas
demanda. El ajuste del punto de operación en un extremo,
permite instalar el interruptor de un lado en las pared o tablero,
permitiendo acceso al tornillo de ajuste.
1-1/8
[28.57]
1/8 FEMALE NPT
HIGH PRESSURE
CONNECTION
1/2 MALE NPT
MOUNTING SPUD
3/4
[19.05]
1/8 FEMALE NPT
LOW PRESSURE
CONNECTION
2-3/32
[53.18]
2-1/8
3-27/32
[53.98]
[97.63]
CLEARANCE FOR
COVER REMOVAL
Construction and dimensions. Series 1823 pressure switches.
SPECIFICATIONS
Service: Air and non-combustible, compatible gases.
Wetted Materials: Consult Factory.
Temperature Limits: -30 to 180°F (-34 to 82.2°C). 1823-00,
-20 to 180°F (-28.9 to 82.2°C).
Interruptor para Ambiente Húmedo (MIL)
Pressure Limits: 10 psig (68.95 kPa) continuous, 25 psig
El modelo 1820 puede ser fabricado son un sello especial a
prueba de intemperie, o para aplicaciones con alta humedad.
Similar al modelo 1823, excepto que la banda de operación es
mayor.
(172.4 kPa) surge.
Especifique el modelo 1820 (Rango No.) “Mil” en su orden.
Electrical Rating: 15 A @ 120-480 VAC, 60 Hz. Resistive 1/8
Switch Type: Single-pole double-throw (SPDT).
Repeatability: ±2%.
HP @125 VAC, 1/4 HP @ 250 VAC, 60 Hz. De-rate to 10 A for
Approximate
Dead Band
Model
Number
Operating
Range,
Inches W.C.
At Min.
Set Point
At Max.
Set Point
1823-00
1823-0
1823-1
1823-2
1823-5
1823-10
1823-20
1823-40
1823-80
0.07 to 0.22
0.15 to 0.5
0.3 to 1.0
0.5 to 2.0
1.5 to 5.0
2.0 to10
3 to 22
5 to 44
9 to 85
0.05
0.06
0.08
0.10
0.14
0.18
0.35
0.56
1.30
0.05
0.06
0.08
0.12
0.28
0.45
0.70
1.10
3.0
operation at high cycle rates.
Especificaciones:
Interruptor de presión diferencial operado por diafragma de 4”, para
activar un interruptor de presión tipo simple polo doble tiro. El diafragma
esta controlado por un resorte calibrado que se puede ajustar para fijar
la presión diferencial exacta a la cual el interruptor actuara. El movimiento
del diagragma es transmitido al botón del interruptor por un medio
mecánico. Interruptor Dwyer Instruments, Inc. Catalogo No. 1823-__ __
para el rango de operación requerido.
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A.
Electrical Connections: 3 screw type, common, normally open
and normally closed.
Process Connections: 1/8˝ female NPT.
Mounting Orientation: Diaphragm in vertical position. Consult
factory for other position orientations.
Set Point Adjustment: Screw type inside mounting spud.
Weight: 1 lb, 5 oz (595 g).
Agency Approvals: CE, UL, CSA, FM.
Phone: 219/879-8000
Fax: 219/872-9057
www.dwyer-inst.com
e-mail: [email protected]
E-53(spanish)
7/2/03
4:19 PM
Page 2
INSTALACIÓN:
1-1/2 [38.10]
1-1/4 [31.75]
3/32 [2.38]
1/8 FEMALE NPT
LOW PRESSURE
CONNECTION
1/2 FEMALE NPT
CONDUIT
CONNECTION
Ø5/16 [7.94]
MOUNTING
HOLES
TYP 4 PLACES
N.C.
COM .
6 [15.40] 4 [101.60]
SQ
TYP
N.O.
1. Seleccione una ubicación libre de vibración excesiva, en donde el
agua o aceite no entre al interruptor. Revise encapsulados
especiales para aplicaciones especiales.
2. Mientras no se requiera otra, las conexión de presión inferior es
recomendada. Monte el interruptor con el diafragma en posición
vertical, el interruptor debe recalibrarse para cada cambio de
posición.
3. Conecte el interruptor a la fuente de presión diferencial. Tubo
metálico con diámetro de 1/4” es recomendado, pero cualquier
sistema de tubería que no restrinja el flujo de aire es bueno.
4. Conexiones eléctricas estándar de los interruptores SPDT, común,
NA y NC. Los contactos cambian cuando se incrementa la presión
del punto de operación.
5. La carga del interruptor no debe exceder los 15 Amp.
Especificados. Las capacidades decrecen con altas cargas
inductivas y ciclos rápidos de actuación, por lo que en estos casos
los limites de corriente deben ser 10 Amp. 0 menores para
incrementar la vida del interruptor.
3
[76.20]
6-3/4
[171.45] TYP
7-1/2
[190.50]
3/4 [19.05]
CLEARANCE FOR
COVER REMOVAL
1-1/2 [38.10] TYP
1/8 FEMALE NPT HIGH
PRESSURE CONNECTION
4-1/6
[103.19]
1-7/16
[36.53]
Encapsulado a Prueba de Intemperie
Encapsulado de acero para condiciones húmedas y/o aceitosas, soporta
pruebas de 200 horas de spray salino, pesa 5-1/2 libras. El interruptor
debe ser instalado en la planta al momento de su fabricación.
Especifique “WP” mas el modelo del interruptor en catalogo.
AJUSTES:
1. Si el interruptor ha sido calibrado en fabrica, revise el punto de
operación antes de ponerlo en servico.
2. De lo contrario, siga los siguientes pasos:
A. Para ajustar el punto de operación, gire el tornillo de calibración
en sentido de las manecillas del reloj para aumentar el valor y en
contra de las manecillas del reloj para dis minuir el valor del punto
de operación.
B. Lo siguiente se recomienda para calibrar o revisar la calibración:
Use una T con tres mangueras plásticas, tan pequeñas como sean
posible. Conecte una manguera al interruptor de presión, otra al
manómetro y por la tercera aplique la presión de esta forma podrá
ajustar el interruptor a la presión requerida lo mas exacto posible.
1/8 FEMALE NPT
HIGH PRESSURE
CONNECTION
Ø5/16 [7.94]
TYP 4 PLACES
1/2 FEMALE NPT
COUNDUIT
CONNECTION
5-7/8
4-1/4
6-3/8 [149.23]
[107.95]
[161.93] TYP
TYP
4-1/4
[107.95] TYP
1/8 FEMALE NPT
LOW PRESSURE
CONNECTION
7/16
[11.11]
3-3/4
[95.25]
CLEARANCE
FOR COVER
REMOVAL
1-1/16
[26.99]
2-3/4
[70.61]
6-15/16
[176.21]
Encapsulado a Prueba de Explosión
Encapsulado a base de Hierro y Aluminio, pesa aproximadamente 7-1/2
libras. Especifique “EXPL” mas modelo del interruptor en catalogo.
©Copyright 2003 Dwyer Instruments, Inc.
Printed in U.S.A. 7/03
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A.
FR# 24-440256-00 Rev. 1
Phone: 219/879-8000
www.dwyer-inst.com
Fax: 219/872-9057 e-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement