Dream Vision Yunzi+ 2 Projector User Manual
advertisement
VERY HIGH CONTRAST VIDEO-PROJECTOR
IR
RF
ACTIVE
GLASSES
Changes
Dreamvision provides this manual ‘as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Dreamvision may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.
Copyright
All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Dreamvision.
Guarantee
Dreamvision provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults. Dreamvision must be informed immediately in writing of any complaints. If the purchaser or third party caries out modifications or repairs on goods delivered by
Dreamvision, or if the goods are handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces.
Normal wear as well as normal maintenance are not subject to the guarantee provided by Dreamvision either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brands and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products of their manufactures.
2 R699840 - Yunzi+ User Manual
TABLE OF CONTENTS
1.0 SAFETY INSTRUCTIONS
5
2.0 INSTALLATION GUIDELINES
...........................................................................................
7
3.0 REMOTE CONTROL UNIT (RCU)
..................................................................................
11
4.0 GETTING STARTED
12
5.0 CONNECTIONS
13
6.0 MENU STRUCTURE
15
7.0 PICTURE ADJUST
18
8.0 INPUT SIGNAL
22
9.0 3D CONTENT AND 3D PROJECTION
...........................................................................
23
10.0 INSTALLATION
24
R699840 - Yunzi+ User Manual 3
11.0 DISPLAY SETUP
27
12.0 FUNCTION
27
13.0 INFORMATION MENU
28
14.0 CINEMASCOPE SETUPS
...................................................................................................
28
15.0 MAINTENANCE
30
16.0 MISCELLANEOUS
33
4 R699840 - Yunzi+ User Manual
SAFETY INSTRUCTIONS
1.0 SAFETY INSTRUCTIONS
1.1 Important Information
Lead-free regulation
This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics
Industries Alliance: http://www.eiae.org.
Information for Users on Disposal of Old Equipment
This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end of life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of this product.
For more information about collection point and recycling of this product, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
1.2 Regional Specific Information
CE mark and Directive 2011/65/EU - ROHS 2 (Europe only)
In accordance with Article 7 and the adoption into national law by 2nd January 2013, this product has been designed and manufactured in accordance with Article 4. The technical documentation and the written declaration of conformity that assesses the product conformity can be provided to the competent National Authority upon an email request to: [email protected]
Other Countries outside the European Union:
If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment.
FCC Information (USA only)
Changes or modification not approved by Dreamvision could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
About the installation place
Do not install the projector in a place that cannot support its weight securely. If the installation place is not sturdy enough, the projector could fall or overturn, possibly causing personal injury.
To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel.
This projector is equipped with a 3-blade grounding type plug to satisfy FCC rule. If you are unable to insert the plug into the outlet, contact your electrician .
To prevent fire or shock hazards, do not expose this appliance to rain or moisture. This apparatus must be earthed.
1.3 Important Safeguards
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
R699840 - Yunzi+ User Manual 5
SAFETY INSTRUCTIONS
HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, use and service.
The power input is auto-ranging from 100 to 240 VAC.
6
Please read these Important Safeguards carefully before use.
• All the safety and operating instructions should be read before the product is operated.
• All warnings on the product and in the operating instructions should be adhered to.
• All operating instructions should be followed.
• Place the projector near a wall outlet where the plug can be easily unplugged.
• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
• Do not use attachments not recommended by the product manufacturer as they may be hazardous.
• Do not use this product near water. Do not use immediately after moving from a low temperature to high temperature, as this causes condensation, which may result in fire, electric shock, or other hazards.
• Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instructions, and should use a mount recommended by the manufacturer.
• When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and uneven surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury to the operator.
Slots and openings are provided for ventilation must not be blocked or covered. Do not place this unit on a bed, sofa, rug or other similar surface.
• This product should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.
• This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product.
• For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line surges.
• Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a risk of fire or electric shock.
• Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
• Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel.
• Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions: a) When the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen on the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the Operation Manual, as an improper adjustment of controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
• When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
• Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
• The product should be placed more than one foot away from heat sources such as radiators, heat registers,
R699840 - Yunzi+ User Manual
INSTALLATION GUIDELINES stoves, and other products (including amplifiers) that produce heat.
• When connecting other products such as VCR’s, and personal computers, you should turn off the power of this product for protection against electric shock.
• Do not place combustible behind the cooling fan. For example, cloth, paper, matches, aerosol cans or gas lighters that present special hazards when over heated.
Do not look into the inside of this unit through vents (ventilation holes). Do not look at the illumination lamp directly by opening the cabinet while the illumination lamp is turned on. The illumination lamp also contains ultraviolet rays and the light is so powerful that your eyesight can be impaired.
• Do not drop, hit, or damage the light-source lamp (lamp unit) in any way. It may cause the lightsource lamp to break and lead to injuries. Do not use a damaged light source lamp. If the lightsource lamp is broken, ask your dealer to repair it. Fragments from a broken light-source lamp may cause injuries.
• The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the light source lamp. If anything is unclear, please consult your dealer.
• Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching fixture of the projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal injury.
• The power supply voltage rating of this product is AC120 V, AC100 V – AC240 V, the power cord attached conforms to the following power supply voltage. Use only the power cord designated by our dealer to ensure
Safety and EMC.
• When it is used by other power supply voltage, power cable must be changed. Ensure that the power cable used for the projector is the correct type for the AC outlet in your country. Consult your product dealer.
• Caution: Do not allow any unqualified person to install the unit. Be sure to ask your dealer to install the unit
(e.g. attaching it to the ceiling) since special technical knowledge and skills are required for installation. If installation is performed by an unqualified person, it may cause personal injury or electrical shock.
2.0 INSTALLATION GUIDELINES
2.1 Introduction
This product is powered by a three-chip LCoS light engine and uses three Full-HD panels to project a picture of up to 3840 x 2160 pixels (Ultra HD, 4K). It supports both Standard and High Definition video formats up to 4K inputs (Ultra HD 4K: 3840x2160 pixels) on one of the two available HDMI inputs.
Supported 2D signals
480p, 576p, 720p@50/60, 1080i/p@50/60, 1080p/24, 4Kp24/25/30: 3840×2160@24/25/30Hz, 4Kp50/60:
3840×2160@50/60Hz (YCbCr 4:2:0 only).
2.2 THX-3D Display Certification
The THX-3D Display certification aim to reproduce faithfully images at home according to the intentions of the film director during playback of 2D and 3D images, and they are the proof of high definition and high quality, indicating that Yunzi+2&3 have cleared more than 400 rigorous image quality tests including accuracy of color reproduction, cross-talk, viewing angle and video processing performance. The THX certification features by using THX picture mode:
• Correct Gamma and Color Temperature
• No Overscan or Scaling
• Correct High Definition color Gamut
The Best in Class Parameters also include ANSI and Sequential contrast, luminance and color Uniformity, color tracking with gray scale, optimum brightness, deinterlacing performance, jaggie and countouring.
Supported 3D signals
This unit is compatible with 3D playback. The source can be connected using one of the two available HDMI inputs. This unit is compatible with the following 3D formats:
• 1080p @ 23.98/24Hz - Frame Packing, Top & Bottom and Side-by-Side
• 720p @ 50 or 59.94/60Hz - Frame Packing, Top & Bottom and Side-by-Side
• 1080i/p @ 50/60Hz - Side-by-Side
R699840 - Yunzi+ User Manual 7
INSTALLATION GUIDELINES
2.3 Environment of Use
This unit makes use of a light source lamp that reaches a high temperature during projection. Do not allow projection under the following conditions:
• Projection with the unit laid on sides.
• Projection at a location that blocks the air inlets or exhaust vents.
• Projection at a place exposed to air blasts from an air conditioner.
Allowed Inclination during operation
Due to the lamp position and operating angle, this unit cannot operate with more than 5° angle horizontally and
15° angle vertically. This unit cannot be operated on the side
15°
5°
2.4 Air-Flow and Space Requirements
This unit can be installed in table, ceiling, rear table or rear ceiling position. Make sure that the unit is installed within the space requirements described below (A: air inlets, B: air outlets). This unit needs at least 20cm of non- obstructed space on each side to allow a sufficient air flow.
A
B B
A
B A
A
Air flow.
8
2.5 Ceiling Mounting the Unit
When mounting of this unit is required, make use of the 4 screw holes (M5x20 screws) at the bottom of this unit indicated by the letter A. Allow sufficient space around the air inlets to avoid blocking them.
Precautions for Ceiling-mount
• To ceiling-mount this unit, special expertise and techniques are necessary. Be sure to ask your dealer or specialist to perform mounting.
• Do not mount at places that may be subjected to vibration and shock.
• Depth of the screw holes (A) is 23 mm. Use at least 13mm long screws but not longer than 23mm as you may damage inside the projector.
• Install at a safe place in case this unit or a part of it may drop. If the light-source lamp is broken, small pieces of glass from the mesh of the filter may appear outside the unit.
• Regardless whether the unit is still under guarantee, Dreamvision d
A
A
D
A
A
R699840 - Yunzi+ User Manual
INSTALLATION GUIDELINES is not liable for any product damage caused by mounting the unit with third party ceiling mount or when the environment is not suitable for ceiling-mount.
Dimensions
• Distances between left and right holes is D = 337 mm.
• Distances between front and back holes is d = 290 mm.
2.6 Projection Distance
Projection Screen
Diagonal Size
(Aspect Ratio 16:9)
50” (127 cm)
60” (152 cm)
70” (178 cm)
83” (211 cm)
100” (254 cm)
110” (279 cm)
Projection Screen
Base Size
(Aspect Ratio 16:9)
43.6” (111 cm)
52.3” (133 cm)
61.0” (155 cm)
72.3” (184 cm)
87.2” (221 cm)
95.9” (244 cm)
Projection Screen
Height
(Aspect Ratio 16:9)
24.5” (623 cm)
29.4” (747 cm)
34.3” (872 cm)
40.7” (103 cm)
49.0” (125 cm)
53.9” (137 cm)
Yunzi+
Projection Distance
151 cm - 305 cm
178 cm - 366 cm
209 cm - 428 cm
251 cm - 507 cm
301 cm - 613 cm
331 cm - 675 cm
138” (350 cm)
150” (350 cm)
120.3” (306 cm)
130.7” (332 cm)
67.7” (172 cm)
73.5” (187 cm)
418 cm - 843 cm
453 cm - 860 cm
180” (457 cm) 156.9” (306 cm) 88.2” (224 cm) 545 cm - 1107 cm
200” (508 cm) 174.3” (443 cm) 98.1” (249 cm) 606 cm - 1230 cm
• The projection screen sizes and projecting distances in the table above are provided only as a guide. Please use them as reference during installation.
• The distances are calculated for a projection image of 16:9 aspect ratio
2.7 Setting the Lens and using Lens Memories
Adjust the picture position
The optimum image can be obtained when the centre of this projector’s lens and the screen are placed perpendicular to each other. Take note of the projection angle when placing them. You can also use up to +/- 15° up and down position and configure trapezoidal correction.
Horizontal Shift
+/- 34%
Vertical Shift
+/- 80%
Screen Height
(H)
Screen Base
(H)
This unit comes with a vertical and horizontal shift to suit most installations. Make sure that your installation does not exceed 80% vertical offset and 34% horizontal offset to avoid trapezoidal correction.
This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen
R699840 - Yunzi+ User Manual 9
INSTALLATION GUIDELINES position
Adjust the picture to your screen.
• The Vertical Shift level is between -80% and 80% of the Screen Height (0.80 x H).
• The Horizontal Shift level is between -34% and 34% of the Screen Base (0.34 x B).
• If the projector is not installed perpendicularly to the screen, use keystone correction to fulfill your screen.
Note that using keystone correction, may be disabled by 3D projection. If you want the best possible 3D pictures, It is not recommended to use trapezoidal correction.
• If you plan to use the vertical and horizontal shifts without keystone correction, make sure to not exceed the values contained in the tab below:
Left / Right shift max. up / down shift
0%
80%
5%
74%
10%
66%
15%
57%
20%
47%
25%
34%
30%
18%
34%
0%
• Adjust the picture position
The Yunzi+ projector has motorized vertical and horizontal shifts. Browse into the Menu to the [Lens Control] setting into the Installation menu, select the shift adjustment. Or use the direct access button on the Remote
Control Unit [Lens Control] to make the lens adjustment. You can use self-generated test pattern of the projector or an external pattern, from a calibration DVD by example, by setting the Adjust pattern option to Off.
• Adjust the picture Zoom
Into the [Lens Control] menu, press the [Ok] button to access the Zoom adjustment. Use the up and down buttons to adjust the picture size until the screen is completely filled.
• Adjust the Picture Focus
From the [Lens Control] menu, press the [Ok] button to access the Focus adjustment. Use the up and down buttons to adjust the picture focus
Using Lens Memories
You can save the current picture position, zoom and focus in up to 5 different Lens Memories (10 for Yunzi+2&3).
Each memory stores the current position, zoom, focus of the lens and you can also set a custom name of 10 characters or less.
• Saving current lens setup
Fist step is to set the lens to fill the desired screen. Then go into the Menu > Installation > Lens Control, Select
Lens Memory Save and choose a free slot available. You can call back anytime later this current lens setup using the direct access button [Lens Mem]ory on the RCU.
• Limitations of use
Each memory can store a different picture size and position, but there are limitations on the possible pictures sizes and positions because of the projector being at a fixed location. In order to calculate the best position of the projector toward the screen, the installer has to make sure that among the different desired pictures, the smaller one with the smaller zoom, is within the offset limits (horizontal and vertical shifts) of the projector. Once the position of the projector is determined by the smallest possible picture, double check that the larger one does not exceed the zoom capacity.
10 R699840 - Yunzi+ User Manual
REMOTE CONTROL UNIT (RCU)
3.0 REMOTE CONTROL UNIT (RCU)
Stand by
Selects an [Input]
[Lens Control]
Focus, Zoom, Shift
Switches, edits [Lens Memory]
M.P.C. (4K picture Settings)
[Hide] the current display
Display [Menu]
Selects a Picture Mode
Gamma Adjust
Color Temp. Adjust
INPUT
PHOTO
Power [On]
Displays [3D Setting] menu
INFO.
Displays [Info] menu
Displays [Env. Setting] menu
Sets the [Lens ap.]erture
Turns on/off the analysis screen
Displays the effects applied to the picture (MPC or Color Profile)
Backlight button
Confirm button
[Back] to previous menu
Yunzi+1
Selects a Picture Mode
Basic Picture Adjust
Selects [3D Format]
Displays [3D Setting] menu
CMD Clear Motion Drive
Color Profile Adjust
Yunzi+2&3
The remote control unit can be used by having the signal reflected off a screen, as the effect of signals reflected differs with the type of screen used, operable distance may decrease.
If the remote control has to be brought closer to the projector to operate, it means that the batteries are wearing out. When this happens, replace the batteries. Always insert the batteries according to the + and - marks.
R699840 - Yunzi+ User Manual 11
GETTING STARTED
4.0 GETTING STARTED
4.1 General View
Front side
Optical Lens*
Air Inlets
Operating LEDs
Front IR receiver
(*) Optical Lens: On the Yunzi+2&3 models, the optical lens is protected by a motorized lens cover.
Rear side
Input Panel Lamp trap
Navigation buttons
Main Power Air Outlets
• Input Panel: connect your video source to the correct input.
• Main Power: connect the power cord as shown below.
• Lamp trap: see “15.3 Replacing the Lamp”, page 31 for more details about lamp replacement.
4.2 Connecting the Power Cord
• Before plugging in the Power Cord, ensure that all devices have been connected to their respective inputs of this unit.
• Connect the power cord to the power input terminal of the projector.
12
When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air inlets or exhaust vents by standing the projector on its end or laying it on its side.
R699840 - Yunzi+ User Manual
4.3 Operating and Navigation Buttons
Power button
STANDBY/ON
Input source
INPUT
OK
OK button
Directional keys
MENU BACK
Menu
Back
Button
Power
Input source
OK button
Directional keys
Menu
Back
Description
To turn ON or OFF the projector.
To switch input source between HDMI 1 and HDMI 2.
To select or to confirm action.
To navigate into On Screen Display (OSD) Menu.
To display On Screen Display (OSD) Menu.
To return to previous menu or cancel action.
5.0 CONNECTIONS
5.1 Caution when connecting a Device to HDMI Input
CONNECTIONS
Prior to connecting any device to this unit, switch the projector in standby mode. Never connect a HDMI source to this unit when the projector is in operate mode. The HDMI termination is a self-powered connection and can cause electric discharges.
If a HDMI input is locked to a fixed resolution or cannot be synchronised correctly, switch OFF this unit,
UNPLUG the main power cord for a few minutes before powering it up again.
R699840 - Yunzi+ User Manual 13
CONNECTIONS
5.2 Connecting a Video Source to the Projector
HDMI 1 HDMI 2
3D syncro
Emitter
Audio/Video Connection
HDMI 1, HDMI 2
(DVI compatible)
3D Synchro output
Device to connect
HDMI or DVI-D sources: Blu-ray Disc player, DVD-player equipped with HDMI output, Game Console, Computer with DVI-D output.
3D synchro emitter to control active shutter glasses. 3-PIN mini-DIN interface,
12V.
This unit supports up to 4Kp60 inputs, make sure to use high quality HDMI cables rated for 4K HDMI 1.4 or HDMI 2.0 standards.
5.3 Connecting an Automation or Control device
LAN to rooter for Automation
14
LAN
RS-232C for Automation
Connection
RS-232 C
12V Trigger
12V Trigger
Device to connect
Automation Device, Control Device or Computer with RS-232 capability.
DC power supply output 12V@140-300mA to control either a screen or an anamorphic lens motorization.
Automation Device, Control Device or Computer with RJ-45.
CONNECTING AN AUTOMATION/CONTROL DEVICE
This unit can control or be controlled by using several input/output terminals. Each terminal is ruled by specific protocols. Please refer to Appendix for more information.
R699840 - Yunzi+ User Manual
MENU STRUCTURE
6.0 MENU STRUCTURE
MAIN MENU
Picture Adjust
SUBMENU
Picture Mode
(5+4 User)
Picture Modes (Yunzi+2&3)
(total of 12 + 4 User)
(*) for expert users, require individual calibration
Advanced Picture Mode
(press OK)
Color Profiles the list varies upon current
Picture Mode
(*) require individual adjustment and/or calibration
Color Profiles (Yunzi+2&3) the list varies upon current
Picture Mode
(*) require individual adjustment and/or calibration
AVAILABLE OPTIONS
(Digital Cinema)
(SF movies or animes)
(Video programs)
(Concerts, theatrical rep.)
Cinema
Animation
Natural
Stage
(available only for 4K50/60p input) 4k50/60p
User1
User2
User3
User4
(Movies)
(Photos)
Film
Photos
THX
THX bright(*)
THX dark(*)
ISF Day(*)
ISF Night(*)
Clear Black
Lamp Power
Lens Aperture
Off, Low, High
Low, High
(standard)
(more contrasted)
Auto 1
Auto 2
Manual
User Name Edit (if f User 1 - 4 selected)
-15 +0 edit name 10 char. max
(HDTV)
(Digital Cinema standard)
(Animations)
(TV, sports)
(Live concerts)
(3D movies)
(3D animations)
(3D broadcasts, 3D TV)
(Live 3D concerts)
(available only with User P.Mode)
Standard
Cinema
Animation
Natural
Stage
3D Cinema
3D Animation
3D Videol
3D Stage x.v.Color
Custom 1 - 5(*)
(Eastman Kodak movies)
(Fujifilm movies)
(Technicolor movies)
(HDTV)
(Movies)
(Digital Cinema standard)
(Animations)
(Richer colors than Anime1)
(TV, sports)
(Computer inputs)
(Live concerts)
(THX)
(3D films)
(3D movies)
(3D TV programs, sports)
(3D animations)
Film1
Film2
Film3
Standard
Cinema1
Cinema2
Anime1
Anime2
Video
AdobeRGB
Stage
THX
3D Film
3D Cinema
3D Video
3D Animation
(3D photo materials)
(3D concerts)
(3D THX)
(available only with User P.Mode)
3D Photo
3D Stage
3D THX x.v.Color
Custom 1 - 5(*)
R699840 - Yunzi+ User Manual 15
MENU STRUCTURE
Advanced Color Profile
Color Temp.
Advanced Color Temp
Gamma
Advanced Gamma
MPC Level
(**) cannot be adjusted for x.v.Color input
Input Signal
Clear Motion Drive
Brightness (**)
Contrast (**)
Color (**)
Tint (reddish to greenish) (**)
Reset Profile settings
Input level
Color Management:
Color selection
Axis Position
Hue
Saturation
Brightness
Reset
Off / On
-30 +30
-30 +30
-30 +30
-30 +30
Confirm
Xenon Modes (Yunzi+2&3)
(Film projector)
(DCI projector)
(Cooler than DCI)
Preset value:
Xenon1
Xenon2
Xenon3
5500K - 6000K - 6500K - 7000K
7500K - 8000K - 8500K - 9000K
9500K - High Bright - Custom 1-3
If Custom 1-3, choose Correction Value
Gain and Offset
Reset settings
Confirm
If Color Profile is Film1 to 3
(standard)
(more contrasted)
If Color Profile is not Film
(fixed for x.v.Color)
If Color Profile is THX
Film1
Film2
Custom1 to 3
Normal
Brightness Priority
Contrast Priority
Gradation Priority
Custom1 to 3
THX
If Custom1-3, choose Gamma Corr. Value
Normal
Brightness Priority
Color Selection
Picture Tone
Dark Level
Bright Level
Reset
Contrast Priority
Gradation Priority
1.8 to 2.6
Import
White / Red / Green / Blue
-16 +16
-7 +7
-7 +7
Confirm
4K e-shift (4K)
Resolution
Enhance
Dynamic Contrast
Smoothing
Noise Reduction
Reset
On, Off
Auto, 4K, 1080p,
1080i / 720p, 480p
0 - 100
0 - 100
0 - 100
0 - 10
Confirm
Off, Low, High, Inverse Telecine
-50 +50
-50 +50
-50 +50
-50 +50
Confirm
Auto
(16 - 235) Standard
(0 - 255) Enhanced
(16 - 255) Super White
16 R699840 - Yunzi+ User Manual
Input Signal
Installation
R699840 - Yunzi+ User Manual
MENU STRUCTURE
Color Space
(fixed to YCbCr(4:2:0) with
4Kp50/60 input)
Auto
YCbCr(4:4:4)
YCbCr(4:2:2)
RGB
On, Off Control with HDMI (CEC)
Aspect (Video only) if 3D, only 16:9 is available
Aspect (PC only)
Progressive (480i, 576i, 1080i)
Mask
3D Setting
Picture Position
5%, 2.5%, Off
Custom
Auto, Off
Top 0 - 28
Bottom 0 - 28
Left 0 - 48
Right 0 - 48
3D format
Auto / Side-by-Side / Top & Bottom / 2D
2D to 3D Conversion
Parallax
Crosstalk Cancel
On, Off
-15 +15
-8 +8
Horiz., Vert.
Lens Control
Pixel Adjust
4:3
16:9
Zoom
Auto
1:1
Full
Focus
Zoom
Shift
Image Pattern
Lock
Lens Memory Select
Lens Memory Save
Lens Memory Name Edit
Lens Center
Lens Cover (Yunzi+2&3)
Adjust
Adjust Area
Adjust Color
Adjust Pattern Color
Adjust (Pixel)
Adjust (Fine)
Reset
On, Off
On, Off
10 char. max
Confirm
Auto, Open
Off, Memory1, Memory2
Whole, Zone
Red, Blue
White - Cyan/Yellow
Installation Style
Keystone (vertical)
Pincushion
Anamorphic
High Altitude Mode
Environment Setting
(vert. stretch)
(hor. squeeze)
Front
Ceiling Mount (Front)
Rear
Ceiling Mount (Rear)
-16 +16
0 +16
Off
A
B
(900m or higher) On / Off
Adjust On, Off
Screen Adjust (Color Profile is not Off) On, Off
Screen No.
Screen Size (inch diag.)
Viewing Distance
Wall Color
001 - 106
60 - 200
1m - 10m
Light - Dark
17
PICTURE ADjUST
Display Setup
Function
Back Color
Menu Position
Signal Display (active input)
Logo
Language
Trigger
Off Timer (in hours)
ECO Mode
Network
Blue, Black select position
On, Off
On, Off
DHCP Client
IP Address
Subnet Mask
Default Gateway
Mac Address
Set
Press [Menu] + [Back] select between 13 languages
Off
On (Power)
On (Anamorphic)
1H, 2H, 3H, 4H, Off
On, Off
On, Off
192.168.0.2
255.255.255.0
192.168.0.254
Display MAC
A, B
Confirm
Information
Remote Code
Lamp Reset
Input
Source
Deep Color
Color Space
Lamp Time
PS Version
7.0 PICTURE ADJUST
7.1 Picture Modes and Color Profiles
The preset Picture Modes are available and they can be applied to any input. A picture mode retains the picture adjustments. When adjusting the Picture Mode, you can also select pre-configured Color Profiles.
Yunzi+1 picture modes
Video
Source
Picture mode
Color Profiles
Digital Cinema or HDTV
Cinema
Cinema
Standard
3D Cinema
Animation, vivid movies
Animation
Animation
Standard
3D Animation
Dramas or Videos
Natural
Natural
Standard
3D Video
Live concerts or Spectacles
Stage
Stage
Standard
3D Stage
Yunzi+2&3 picture modes
Video
Source
Picture mode
Color Profiles
Movies in general
Film
Film1
Digital
Cinema or HDTV
Cinema
Cinema1
Animation vivid movies
Animation
Anime1
Dramas or Videos
Natural
Video
Film2
Film3
Cinema2
Standard
Anime2
Standard Standard
3D Film 3D Cinema 3D Anime 3D Video
Photos
Photo
Adobe RGB
Standard
3D Photo
Live concerts,
Spectacles
Stage
Stage
Standard
3D Stage
THX sources
THX
THX
3D THX x.vColor inputs may be correctly decoded when using on of the four available User “Picture Mode” and selecting x.v.Color “Color Profile”. The User Picture modes can be renamed to a more convenient name.
18 R699840 - Yunzi+ User Manual
PICTURE ADjUST
There are 12 Color profiles for 2D inputs and 7 for 3D inputs, depending on the selected picture mode, you may choose an available color profile preset:
• Film1 available with Film Picture Profile, uses the Xenon filter and adjusted to Eastman Kodak film tone
• Film2 available with Film Picture Profile, uses the Xenon filter and adjusted to Fujifilm film tone.
• Film3 available with Film Picture Profile, uses the Xenon filter and adjusted to Technicolor film tone.
• Standard will bring rich and saturated colors found in HDTV, available with almost any selected Picture Mode.
• Cinema1 available with Cinema Picture Profile and adjusted to HDTV standards
• Cinema2 available with Cinema Picture Profile and adjusted to DCI standards.
• Anime1 best suited to Hollywood animes.
• Anime2 best suited to Japanese animes.
• Video color profile is best suited to TV and Sport programs.
• AdobeRGB color profile adjusted to Adobe RGB standard.
• Stage best suited to live concert.
• x.v.Color matches the color space of x.v.Color standard.
7.2 Advanced Picture Mode
Clear Black
Smooth out the black areas to obtain clear zone by eliminating electronic white noise in these areas. Turn it Off or set the correction to Low for a mild effect or High for a strong effect.
Lamp Power
Set the lamp power used by the current Picture Profile:
Low: lamp is set to 180W
High: lamp is set to 230W.
To avoid any damage to the lamp, you shouldn’t change the lamp power within 90 seconds from the projector startup or 60 seconds after lamp power change.
Lens Aperture
The lens is equipped with a variable electronic aperture. This function is used with a real time analysis of the video picture projected that optically adjusts the light output depending on the viewing conditions by controlling the aperture dynamically: when set to Auto 1, the iris will automatically be set to the optimal opening. Auto 2, the curve is altered so that the gradation is more visible. The Manual setting lock the iris to a fixed position, adjust to the best aperture from partially closed (-15) to fully opened (0).
User Name Edit
You can edit the picture modes names User1 to 4 using a maximum length of 10 characters. You can use alphabet letters, numbers and symbols:
Select cursor
Picture Adjust
>>
User Name Edit
Name User 1 Input cursor
Character list
SPACE
Exit
MENU
Select
Clear All Clear
Operate
BACK
OK a) Select the user name you want to edit from User1 to User5. Press [OK] to enter the edit mode.
b) The input cursor displays the place where the new character will be insert. It moves automatically as a character is selected. Use [UP], [DOWN], [LEFT] or [RIGHT] to select a character and press [OK] to insert.
c) Press [BACK] to exit edit mode.
Clear: To delete a character: Move the cursor to the desired location and press [OK] to delete the specific character.
R699840 - Yunzi+ User Manual 19
PICTURE ADjUST
All Clear: To delete all characters. OK: To save the current name, a save confirmation will appear.
7.3 Advanced Color Profile
Expert Calibration is accessed only by using a programmable IR-RCU, RS-232C or LAN control. Two additional sets of Picture Modes can be activated. Each set designated as THX and ISF profiles have to be calibrated. Once done, these profiles are stored and displayed in the picture mode menu list but will not be modifiable. Additionally the Calibrator can certify his action by setting in the Information Menu his name or company name.
Color Management (TSL adjustments)
The Color Management gives the installer an unique calibration ease with the integrated Color Adjustment menu: each primary, secondary colors and orange can be independently calibrated to obtain a precise color balance in a snap. Adjust the Red, Green, Blue, Yellow, Cyan, Magenta and Orange Tints, their saturations and luminances and store them into Custom profiles.
7.4 Color Temperature
Color temperature stands for the spectral properties of a light source. Low color temperature implies warmer ambiance (more yellow/red) while high color temperature implies a colder light (more blue). Depending on the
Picture Profile selected, this setting can be set to:
• Preset: from 5500K / warm colors, up to 9500K / cold colors in steps of 500K.
• Xenon1(*) uses the Xenon filter and color compensation to reproduce a film projector
• Xenon2(*) uses the Xenon filter and color compensation to reproduce a digital cinema projector
• Xenon3(*) same as Xenon2, but within a cooler temperature.
• High Bright used for maximum brightness output available.
• Custom1, Custom2 and Custom3 can be used to adjust color temperature to specific environment.
A Custom setting allows a fine adjustment of a Color Temperature by selecting it in the Correction Value menu.
Adjust the Gain values (bright part) and Offset values (dark part) for each color Red, Green and Blue.
Accurate color temperature may require professional tools such as dedicated software and colormeter.
Wait at least 15 minutes after startup before modifying the picture settings.
(*) Xenon Modes are exclusive to Yunzi+2&3 models.
7.5 Advanced Color Temperature
When selecting a Color temperature, you can set the Gains and Offsets of each primary color: red, green and blue to finely adjust the color balance.
7.6 Gamma
Gamma is the relationship between the color values of the data and the color values displayed. The Gamma coefficient makes it possible to adjust the brightness of the midtones only without affecting the very bright and very dark areas. If gamma is set too high, middle tones appear too dark. If it’s set too low, middle tones appear too light.
Depending on the current active Picture mode, the Gamma setting can be set to:
• Normal: Standard setting for normal viewing.
• Brightness Priority: Places more emphasis on the brightness than the Normal setting.
• Contrast Priority: Places more emphasis on the contrast than the Normal setting.
• Gradation Priority: Places more emphasis on the gradation than the Normal setting.
• Custom1 to Custom3: fine tune the gamma setting according to the user’s preference.
• NB: when Color Profile is set to x.v.Color, gamma setting is fixed to Normal.
Additional Gamma settings when Film Color Profile is selected (Yunzi+2&3):
• Film1: standard gamma
• Film2: slightly more contrasted gamma
20 R699840 - Yunzi+ User Manual
PICTURE ADjUST
7.7 Advanced Gamma
Correction Value
The Custom data can be set to:
Correction Value: a unique value that will act as a gamma coefficient between 1.8 and 2.6, Normal, Brightness
Priority, Contrast Priority, Gradation Priority, 1.8-2.6 or Import.
Color Selection
Select the color to which the Picture Tone, Dark / Bright Level settings would apply. Choose between White, Red,
Green and Blue.
Picture Tone
It allows a fine adjustment steps of the global picture brightness while maintaining the correct contrast level to keep good black and bright levels. Sets the overall exposure from -16 (under-exposed, darker) up to +16 (overexposed, brighter)
Dark / Bright Level
This setting modifies the gamma curve locally in the dark and bright areas.
• Dark Level adjust gamma curve between 0IRE and 15IRE, each color can be adjusted from -7 to +7.
• Bright Level adjust gamma curve between 85IRE and 100IRE, each color can be adjusted from -7 to +7.
Reset Gamma
Prompt a confirmation to reset the current Gamma settings to default.
7.8 Multiple Pixel Control Level (MPC Level)
4k e-shift
• On: sets this unit to display the video content in 4K resolution.
• Off: sets this unit to display the video content in Full-HD resolution.
Resolution
Set the resolution according to the content your are viewing between : 1080p, 1080i/720p or 480p. The best setting is Auto. By selecting the Auto setting, this unit will automatically detect and select the correct resolution.
Enhance
Enhance: enhances the sharpness of foreground objects detected in the picture.
Dynamic Contrast
Dynamic Contrast: enhances the general contrast of the picture.
Smoothing
Smoothing: enhances the blurriness of backgrounds for increased the global sense of depth.
Noise Reduction
Noise Reduction: reduces the digital noise of the video picture.
Analysis screen
Analysis screen:
You can enlight the different areas processed by the 4K-Interpolation by pressing [Analysis Screen] button or twice the [MPC Level] button on the RCU when browsing the MPC Level sub menu.
-Areas affected by the Enhance parameter are colored Blue and Green.
-Areas affected by the Dynamic Contrast parameter are colored Red and Yellow.
-Areas affected by the Smoothing parameter are colored Black.
Pressing the [Before/After] button enables you to toggle between the state before adjustment and after adjustment.
R699840 - Yunzi+ User Manual 21
INPUT SIGNAL
7.9 Clear Motion Drive (400Hz)
The Clear Motion function uses a 400Hz video processing to render a smooth and clear motion for movies shot at 24Hz or HD movies at 60Hz. Set the correct level between:
• Off: Frame interpolation is disable.
• Low: light frame interpolation with reduced artifacts.
• High: strong interpolation
• Inverse Telecine: dedicated interpolation for 60i and 60p sources originally shot in 24p.
7.10 Contrast
The contrast function is used to adjust the contrast between the light and dark areas of the displayed image. A correct contrast setting is important for good image reproduction. Adjust the Contrast value between -50 and 50.
7.11 Brightness
The brightness function is used to adjust the overall light output. Adjust the Brightness value between -50 and 50.
7.12 Color
The Color function (or Saturation) is used to adjust the saturation levels. Adjust the Color value between -50 and
50.
7.13 Tint
The hue function is used to adjust the color tint to obtain true color reproduction. Adjust the Tint value between
-50 (more red) and 50 (more green).
8.0 INPUT SIGNAL
8.1 Input Level
Sets the dynamic rang of the video input:
• Auto: The input dynamic range is automatically detected and configured.
• Standard: Force dynamic range to 16-235.
• Enhance: Force dynamic range to 0-255.
• Super White: Force dynamic range to 16-255.
8.2 Color Space
Sets the color space of the input signal.
• Auto: The source color space is automatically detected and configured.
• YCbCr(4:4:4): Set color space to YCbCr 4:4:4.
• YCbCr(4:2:2): Set color space to YCbCr 4:2:2.
• RGB: Set color space to RGB 4:4:4.
The color space setting is fixed to YCbCr(4:2:0) for 4K50/60p inputs. Use preferably a video source of 4K24/25p if available to obtain rich colors.
8.3 Control with HDMI (CEC*)
• Off: By default the CEC(*) communications are disabled.
• On: Enables CEC(*) communications to be sent to the projector through HDMI cable.
(*) CEC stands for Consumer Electronic Control
22 R699840 - Yunzi+ User Manual
3D CONTENT AND 3D PROjECTION
8.4 Aspect Ratio
When watching a movie or video program, you can manually set the desired aspect ratio to fill your screen. Select the correct aspect ratio depending on your source:
For Video sources
a) 4:3. The original source is considered as 4:3 format. Generally SDTV broadcasts.
b) 16:9. The picture size is 16:9, generally most recent DVDs, Blu-Ray discs or HDTV broadcasts.
c) Zoom. The zoom function is useful to zoom in the picture and eliminate black bars.
When watching 3D content, only 16:9 aspect ratio is available .
For PC sources
a) Auto. Zoom the picture to fill either the screen height or the screen base which ever happens first.
b) 1:1 mode, pixel to pixel mapping, no scaling.
c) Full. Stretch the picture full screen
8.5 Progressive (only 480i, 576i, 1080i)
Interlaced signals are converted to progressive signals using video images from the surrounding. This function is only available for interlaced input signals: 480i, 576i and 1080i.
8.6 Mask
Depending on your source, you may enable or disable this feature to hide the outer area of the picture. The Mask function can hide the unexpected scaling artefacts found in broadcast program. You can set it to Off, 2.5% or 5% globally or for each side of the screen.
8.7 Picture Position
Depending on your source, you may find that the picture should be adjusted into the screen, adjust the horizontal and vertical position of the picture into the screen. Some signals may not be fully displayed, adjust this setting properly when necessary.
9.0 3D CONTENT AND 3D PROJECTION
9.1 General Information about 3D playback
Comfort and Caution with 3D Content
The closer one looks at stereoscopic images, the greater the binocular disparity, which means greater perception of outward projection. At the same time, the spectator must focus on these outward objects on the screen. The projecting image and the real focus distance cause a great contradiction, this strain contributes to fatigue and discomfort.
Please stop watching if you do not feel well and consult a physician if necessary. People who already have a kind of photosensitivity, sufferers from heart disease, and people in poor physical condition should not watch 3D stereoscopic images. It is also recommended that you take a break periodically.
Prevent child under 5 years old to watch 3D
The comprehensive brain function to judge stereoscopic vision which includes the feeling for real distances, develops while growing up by touching and seeing real objects, but in early childhood, it is still in an underdeveloped state. Even though there are individual differences, children under 5 are still developing. Letting them frequently watch virtual 3D video images can be an obstacle for the development of a comprehensive three-dimensional feel. Additionally, younger children may suddenly become sick, because they continue watching without realizing symptoms like 3D sickness or deterioration of health. Please accompany your child while it watches 3D programs.
R699840 - Yunzi+ User Manual 23
INSTALLATION
9.2 Projector 3D Settings
3D Formats
Use this function to choose the correct 3D input format. Some input signals may contain 3D data such as 1080p
Side-by-Side but encoded as if they were in 2D. This unit may treat them as standard 2D signals and will not project correctly. In such cases, configure the signal manually between Side-by-Side, Top & Bottom and 2D. In other cases, you may select Auto setting.
2D to 3D Conversion
You can use the 2D to 3D Conversion to convert 2D pictures into a quasi-3D picture. The quality of the result may differ from quality of original 2D picture. Turn it On or Off.
Parallax
Use this function to adjust the amount of misalignment of the left and right 3D video images. Adjust settings according to your preference between -15 and +15.
Parallax is an important parameter for 3D movies that directly affects comfort during 3D projection.
Because the parallax value changes with the screen size, it is important to set this parameter to a value with which everyone feels comfortable with the 3D effect. In general, women and children will feel better with a smaller parallax value. Do not hesitate to alter this settings if you feel eye-strains or headaches.
Due to the large screens used in home theaters compared to flat screen TVs, we recommend a negative value of -6 for computer sources and video games in native 3D with large parallax. This setting is best at 0 for Blu-Ray movies aimed for Digital-Cinema audience.
Crosstalk Cancel
Can be adjust with a 3D signal input but not when 2D to 3D Conversion is On. This function is to lessen the residual cross-talk found between 3D video images. Adjust the Parallax value and then the Cross-talk settings in order to cancel the residual cross-talk without loosing picture quality.
Adjustments White, Red, Green and Blue: -8 +8
Negative values reduce visible Crosstalk, positive values bring a brighter 3D picture at the cost of more
Crosstalk.
10.0 INSTALLATION
10.1 Lens Control
24
Focus
Adjust the lens focus to obtain a clear picture.
Zoom
Adjust the lens zoom to fill the screen with the picture.
Shift
Adjust lens shift to center the picture into the screen.
Image Pattern
If set to On, an internal pattern will be generated to adjust the current setting. If you want to use an external generator, turn this option to Off.
Lock
Once the Lens is correctly set, you may lock this setting menu by turning the Lens control Lock to On. Any attempt to access the Lens control menu will lead to the display of a warning message.
Lens Memory Select
Call up saved lens adjustment data to configure the lens to the save settings.
R699840 - Yunzi+ User Manual
INSTALLATION
Lens Memory Save
Store into an available memory the lens focus, zoom and shift configuration. There are 5 memories for Yunzi+1 model and 10 memories for the Yunzi+2&3.
Lens Memory Name Edit
Lens Center
Reset the lens position to the original, central position.
Lens Cover (Yunzi+2&3)
Control the behavior of the Lens Cover:
• Auto: the lens cover opens or closes when the projector switches On or Off.
• Open: the lens cover is always open.
10.2 Pixel Adjust
The pixel adjustment is extremely fine: each color can be adjust within 1/16 pixel steps on 121 individual adjustment zones.
Adjust
Enable the pixel adjustment on Memory 1, Memory 2 or Off.
Adjust Area
Whole: the entire screen is selected for adjustment.
Zone: the screen is divided into 121 adjustment zones.
Adjust Color
Select the color to adjust: Red or Blue.
Adjust Pattern Color
Select a pattern to help the pixel alignment. Settings: White or Green+adjusting Color. Yellow for red, Cyan for blue.
Adjust (Pixel)
This function is enable when the Adjust Area is set to Zone only. You can adjust the selected color position horizontally and vertically by 1-pixel steps.
• H settings: -2 +2
• V settings: -2 +2.
Adjust (Fine)
Use this function to move the selected color within smaller steps.
• H settings: -31 +31
• V settings: -31 +31
Reset
Reset all pixel adjustments to default factory settings.
RCU SHORTCUTS DURING PIXEL ADJUSTMENT:
[GAMMA] button on the RCU switches adjust color parameter between Red and Blue.
[PIC. ADJ.] button on the RCU switches the adjust area parameter between whole and zone. At the same time, the zone cursor will appear on the adjust pattern.
[COLOR SPACE] button on the RCU changes the adjust pattern from white to green+adjust color.
Use the [COLOR TEMP] button on the remote control to change adjustment method from Pixel to Fine tune and switch to the fine tune window.
[BACK] button will exit the Pixel Adjust mode.
R699840 - Yunzi+ User Manual 25
INSTALLATION
Installation Style
Flip the image to the left or right, up or down according to the projection state of the projector:
Front, Ceiling Mount (F), Rear or Rear Ceiling mount (R)
10.3 Keystone (Vertical)
Compensate for trapezoidal distortion caused by installation. Independently to the screen orientation, make sure that the projector is not tilt more than 5% up/down.
• Vertical Keystone from -16 to +16.
10.4 Pincushion
Compensate distortions that may appear with curved screens or anamorphic setups.
NB: When a 3D signal is fed or when Keystone is used, the Pincushion correction cannot be set.
10.5 Anamorphic (works with 3D signal)
• Off: No modification to original picture.
• Mode A: The picture is vertically stretched to fit an installation with anamorphic lens. A cinemascope picture is stretched to completely fill the panels without black bands, using the optimum resolution and brightness.
Anamorphic Mode A.
• Mode B: This setting squeezes horizontally the picture to fit a 16:9 image into cinemascope screen. This setting is to be used with an anamorphic installation where the lens is permanently fixed in front of the unit and to watch 16:9 content in its original format.
Anamorphic Mode B
10.6 High Altitude Mode
Select this when the projector is in a location of low atmospheric pressure. On or Off
10.7 Environment Setting
Turn On or Off the Environment setting. If set to On and to finely tune the picture, you may change the environment settings so that they match your installation:
• Screen Adjust: This setting corrects the color balance derived from the reflective characteristics of the screen
26 R699840 - Yunzi+ User Manual
DISPLAY SETUP without altering the global picture settings. You may select the best template available in the Screen No.
a) 001 - 009: select a profile between 001 and 009 when watching 3D content with 3D shutter glasses. Profile
001 is recommended when using Dreamvision’s active IR 3D-glasses.
b) 010 to 106: select the best compensation profile depending on your screen and environment.
• Screen size: diagonal size in inches set this setting between 60” and 200”.
• Viewing distance is the distance to the screen of the nearest seat in meters, set it between 1m and 10m.
• Wall color, select “Dark” if the walls are black or similar, for any lighter shades select “Light”.
11.0 DISPLAY SETUP
Back Color
Configures the screen color displayed when there is no active input. Set to Blue or Black.
Menu Position
Upper left, Upper right, Center, Lower right, Lower left.
Signal Display
On: Display the source of the input signals after input selection.
Off: Don’t display.
Logo
On: Display D-ILA logo during startup for 5 seconds.
Off: Don’t display.
Language
Choose the OSD language between: English, Japanese, German, Spanish, Italian, French, Portuguese, Dutch,
Swedish, Norwegian, Russian and Chinese.
12.0 FUNCTION
12.1 Trigger
The 12V trigger output can be used to control any compatible devices such as motorized screens or anamorphic kits: The 12V trigger output is 12Vcc, 100mA. Select the trigger output behavior:
• Off: 12V trigger voltage state is always low.
• On (Power):12V trigger state is high when the projector is powered ON. To be used with motorized screens.
• On(Anamo): 12V trigger is high only when Anamorphic Mode A or Mode B is engaged. To be used with motorized anamorphic kits.
12.2 Off-Timer
You can configure this automatic power Off function that will switch off the projector when there is no operation or after a determined timer. Choose the duration of the timer between: Off, 1 hour, 2 hours, 3 hours and 4 hours.
12.3 ECO Mode
This setting when set to On will minimizes the power consumption in the Standby Mode. Additionally, this product will automatically switch Off whenever the input signal is interrupted for 30min.
12.4 Network
When the Communication Terminal selected is LAN, this unit will be visible on the local Network and the following
parameters need to be configured. Refer to section “16.2 LAN protocol”, page 37 for more details.
R699840 - Yunzi+ User Manual 27
INFORMATION MENU
12.5 Remote Code A or B
Select in the projector menu the code A or B according to the code selected on the RCU. You can change the code used by the RCU to communicate with the projector from A to B. To do so, press and hold for 3 sec simultaneously [MENU]+[BACK] buttons on the RCU. All the buttons on the RCU will blink.
• Two blinks indicate that B code is used.
• Three blinks indicate that A code is used.
12.6 Lamp Reset
13.0 INFORMATION MENU
Input Terminal
Displays the active video input.
Input Source
Displays the type of the current video input signal.
Resolution
If the active input is PC input., its resolution is displayed.
H. Frequency
In the case of PC signal, the horizontal frequency is displayed.
V. Frequency
In the case of PC signal, the vertical frequency is displayed.
Deep Color Depth
Displays the color bit depth of the input video signal.
Color Space
Displays the color space of the input signal.
Lamp Time
Displays the accumulated hours of usage of the lamp.
Calibrator
Stores up to 18 ASCII characters set by the Calibrator. Shown only if set during ISF profile adjustment.
14.0 CINEMASCOPE SETUPS
14.1 Lens Zoom or 2.35 Theater System kit
The Yunzi+ centralizes the controls and automation commands for a unique, versatile and unexpectedly simple to operate 2.35:1 theatre experience using Lens Zoom or Anamorphic Lens.
• Up to 10 lens position memories
• Integrated Constant Image Width (CIW) scaler with anamorphic mode A and mode B.
• Dedicated commands to control the 2.35 Theater System kit and picture size on a 2.35:1 screen.
28 R699840 - Yunzi+ User Manual
CINEMASCOPE SETUPS
14.2 Cinemascope setup with Lens Zoom
Select “Menu => Installation => Lens Memory 1”
Zoom in, until the left and right borders of the picture fits the 2.35:1 screen borders. Save the lens position in the lens memory 1. You can also edit the memory 1 name to “Cinemascope”.
Select “Menu => Installation => Lens memory 2”
Make sure to project a 16:9 picture, zoom out until the picture top and bottom fit the top and bottom of the screen.
Adjust the focus and offset if required, then save this position into the memory 2. You can additionally edit the memory name to “Standard”.
Switch format using the Remote Control Unit.
You can now switch between Cinemascope and standard formats easily by using the [Lens Mem]ory button on the RCU and selecting the correct lens memory according to the source format.
Because of the nature of the lens motorization, the precision overtime is not enough to perpetually maintain the correct zoom / focus / position after several zoom in and out. It is required to periodically alter the lens setting.
14.3 Installing a 2.35:1 screen with the 2.35 Theater System kit
Plug the 12V Trigger output of the projector to the Anamorphic motorization
12V Trigger to anamorphic motorization
Connect the lens motorization to the 12V Trigger output.
Configure the function “Menu => Function => Trigger => On (Anamo)”
The “Function => Trigger” menu determines the 12V Trigger output located in the panel input at the rear of this unit. This is a global parameter (for all inputs. Set the 12V Trigger to “On (Anamo)“ mode so that it is most of the time Off and switches On when the picture is in Cinemascope format and Anamorphic mode A is selected. The picture is then vertically stretched and the lens is needed.
• Set 12V Trigger to: “Function => Trigger => On (Anamo)”.
Video source is 16:9: set [Anamo]rphic to Off
When you select a 16:9 input choose the anamorphic OFF to obtain move the anamorphic lens out. Menu
“Installation => Anamorphic => Off”
Video source is Cinemascope: set [Anamo]rphic to Mode A
Select Anamorphic mode A for this input in the menu Input “Installation => Anamorphic => Mode A”.
R699840 - Yunzi+ User Manual 29
MAINTENANCE
[Anamo]rphic modes
OFF Anamo Mode A Anamo Mode B
When you press sequentially the [Anamo]rphic button, you change the mode from OFF, Mode A and Mode B.
• Mode A is intended to be used with an anamorphic lens to watch 2.35:1 content on a 2.35:1 screen.
• Mode B is intended to be used to quickly switch to 16:9 content without moving the anamorphic lens.
The Anamorphic Lens is automatically placed in front of the projector to restore the correct picture aspect ratio.
Appearance on
2.35 screen
OFF
16:9 format
16:9 on 2.35 screen
2.35:1 format
2.35 on 2.35 screen Mode A
When the source switches format....
... press [Anamo] button to obtain the correct anamorphic mode.
15.0 MAINTENANCE
15.1 Cleaning and Replacing the Dust Filters
The filters must be cleaned regularly to allow an efficient air intake. Otherwise, dirt may enter the unit and appear on the screen, preventing you from enjoying the video fully. If dirt has entered the unit or if you need information about the filter, please consult your authorized dealer. A filter cleaning warning appears every 500 hours.
Cleaning procedure
• Pull out the power plug from the outlet while the projector is in standby mode.
• Push up and lift the claw of the filters, pull out the filters.
• Clean the filters with water and dry them, avoiding direct sunlight. In extremely soiled cases, use of a neutral detergent is recommended. Insert the filters in their original positions and make sure that the claws are firmly inserted.
Dust Filter
30 R699840 - Yunzi+ User Manual
MAINTENANCE
15.2 Dirt on the Lens
The lens shall be cleaned using commercial blowers or lens cleaning papers (for cleaning glasses and cameras).
Do not use fluid-type cleaning agents. This may lead to peeling of the surface coating film. The lens surface is fragile. Avoid rubbing it hard or knocking.
15.3 Replacing the Lamp
Light-source Lamp and Lamp Usage Time
The life of light-source lamps used for this unit is about 4000 hours when running this unit in low lamp mode.
• When the lamp power is set to Low, the lamp life is approximately 4000 hours. This average lamp life is not guaranteed and may not reach 4000 hours depending on the operating conditions. Deterioration progresses rapidly when the remaining lamp usage time is short. Get ready or replace with a new lamp when the accumulated usage time exceeds 4000 hours. Depending on the operating conditions, the lamp may have to be exchanged earlier. If the image is dark or if the color tone is abnormal, replace the lamp as soon as possible.
• You can also check the accumulated hours of usage. Please refer to Lamp Time in the Information menu.
When the lamp usage time exceeds 2900 hours.The Lamp replacement message will be displayed on the screen the next three projection starts.
• Press the [BACK] button to clear the display.
ABOUT LAMP REPLACEMENT
If this unit is installed in a constricted place, attempting to replace the lamp in that place may cause injury.
Move this unit to a place large enough to perform work.
Use only genuine replacement parts for the lamp unit. Otherwise, malfunction may occur. Also, never attempt to reuse an old lamp unit. This may cause marked performance deterioration or lamp blowout, thus leading to unit malfunction. Broken pieces of the lamp outside this unit may also cause injuries during lamp unit exchange.
Do not replace the lamp immediately after this unit has been used. The temperature of the lamp is still high and this may cause a burn. Allow a cooling period of 1 hour or more before replacement.
Before replacing the lamp unit, pull out the power plug from the outlet and wait until the STANDBY/ON led is still light red. Replacing a lamp with the plug connected to the outlet may cause injuries or electric shocks.
Procedure for Lamp Replacement
During the lamp replacement process, you may have access to sensitive parts of the projector.
• Loosen the screw on the lamp trap at the rear of this unit.
• Open the lamp Cover and loosen the 2 screws on the lamp unit to release it.
R699840 - Yunzi+ User Manual 31
MAINTENANCE
• Pull out the lamp unit using the handle.
• Insert the new lamp unit until it is firmly in place.
• Tighten the screws of the lamp unit.
• Attach the lamp cover and fasten the lamp trap screw.
Resetting Lamp Time
After installing a new lamp, reset the lamp time using the OSD menu
Turn On the unit.
b) Browse into the menu Function => Reset Lamp Time.
c) Confirm time reset.
CAUTION DURING LAMP RESET
Reset the lamp time only when you have replaced the lamp.
Never reset it when the lamp is still in use. Otherwise, the approximate standard for gauging replacement time may be inaccurate, lamp performance may deteriorate and lamp blowout may occur.
15.4 Troubleshooting
WARNING
(orange/red LED)
LAMP (orange LED)
STANDBY/ON
(green/red LED)
32
When the projector is running for more than 1 minute, the Standby/ON LED will automatically switch
OFF.
1
2
ID WARNING
(orange/red)
-
-
Operating LED
LAMP
(orange)
STANDBY/ON
(green or red)
-
red green
3 -
4
5/6 -
orange
Description
Unit is in standby mode.
Unit is in operate mode.
blinking red Unit is in cooldown mode (switching off).
-
Lamp time has reached 2900 hours, prepare to replace the lamp soon. If used in low power mode, replace the lamp before 4000 hours.
R699840 - Yunzi+ User Manual
MISCELLANEOUS
9
10
11
12
13
14
15
16
17
ID WARNING
(orange/red)
Operating LED
LAMP
(orange)
STANDBY/ON
(green or red)
7
8 continuous red blinking orange
blinking orange blinking red
blinking orange
-
-
Description blinks 1 time: the lamp failed to ignite, restart the projector after a complete cooldown cycle.
blinks 2 times: lamp has shut down during ptojection, restart the projector after a complete cooldown cycle.
blinks 3 times: lamp cover is open. Check that the lamp cover is firmly closed.
blinks 1 time: PSU failed.
blinks 2 times: Cooling fans stop.
blinks 3 times: Internal thermal sensor detects overheating.
blinks 4 times: External thermal sensor detects overheating.
blinks 1 time: Startup or drive circuits failed.
blinks 2 times: Communication with drive circuit failed.
blinks 3 times: Scaler circuit failed.
blinks 4 times: Electrical lens cover failure.
CAUTION: When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air inlets/exhaust vents by standing the projector on its end or laying it on its side.
16.0 MISCELLANEOUS
16.1 RS-232C protocol
Serial communication specifications
Control of this unit is possible using a computer or automation device connected with a RS-232 cross cable
(female - female D-sub 9 pins cable) or LAN/ RJ-45 cable. Communication specifications for this unit are as follows:
Baud Rate
Data Format
Mode
Parity
Start Bit
Stop Bit
X on/off
Flow Control
19200 bps
Binary
Asynchronous
None
1 bit set to high
1 bit set to low
None
None
RS-232C pin assignation
1
6 9
5
Pin
2
3
5
1, 4, 6-9
Signal
RxD
TxD
GND
NC
Function receive data
Signal Direction
PC -> Projector transmit data Projector -> PC ground -
-
Command Format
Header 1 Header 2 Command Command Data
21h 89h 01h 2 - 4 bytes variable
Header 1 : 21h for operating commands or 3Fh for reference command.
Header 2 fixed to 89h 01h
End of Data
0Ah
R699840 - Yunzi+ User Manual 33
MISCELLANEOUS
Commad: from 2 to 4 bytes length
Command Data: variable length
End of Data fixed to 0Ah
Available Operating commands
Function
Connection RS-232
Power
Inputs
RCU code
Power /w confirm
Switch input
Keypad
Hide Display
OSD Menu Position
Lamp Power
Clear Black
400Hz CMD
Picture Mode
Command
00h 00h
50h 57h
49h 50h
53h 55h 52h 43h
52h 43h
52h 43h
52h 43h
52h 43h
52h 43h
50h 4Dh 4Ch 50h
50h 4Dh 41h 4Eh
50h 4Dh 43h 4Dh
50h 4Dh 50h 4Dh
Command Data none
31h
30h
Description
Check the serial connection
Switch the unit On.
Switch the unit in standby mode.
36h
37h
30h
Switch active input to HDMI1
Switch active input to HDMI2
Set unit to receive commands from code A
31h Set unit to receive commands from code B
37h 33h 30h 35h Switch this unit On.
37h 33h 30h 36h Switch this unit Off. (send twice)
37h 33h 30h 38h Switch to next input
37h 33h 37h 30h Switch input to HDMI1
37h 33h 37h 31h Switch input to HDMI2
37h 33h 30h 31h UP
37h 33h 30h 32h DOWN
37h 33h 30h 33h BACK
37h 33h 32h 45h MENU
37h 33h 32h 46h OK
37h 33h 33h 34h RIGHT
37h 33h 33h 34h LEFT
37h 33h 31h 44h Toggle Hide On/Off
37h 33h 44h 30h Switch Hide to On
37h 33h 44h 31h Switch Hide to Off
37h 33h 34h 32h Toggle the OSD menu position
30h
31h
30h
31h
32h
Set Lamp power to Normal
Set Lamp power to High
Off
Low
High
30h
33h
34h
35h
30h 30h
30h 31h
30h 32h
30h 33h
30h 34h
30h 36h
31h 32h
30h 42h
30h 43h
30h 44h
Off
Low
High
Inverse Telecine
Film Mode
Cinema Mode
Animation Mode
Natural Mode
Stage Mode
THX Mode
Photo Mode
4K 50/60p
User 1
User 2
34 R699840 - Yunzi+ User Manual
Function
Picture Mode
Color Profile
Color Profile
Set User1 name
Set User2 name
Set User3 name
Set User4 name
Expert Calibration
(THX)
Expert Calibration
(ISF)
Command
50h 4Dh 50h 4Dh
50h 4Dh 50h 52h
50h 4Dh 50h 52h
50h 4Dh 55h 31h
50h 4Dh 55h 32h
50h 4Dh 55h 33h
50h 4Dh 55h 34h
52h 43h
52h 43h
Set Calibrator name 50h 4Dh 43h 49h
Contrast 50h 4Dh 43h 4Eh
Brightness
Color
Tint
R699840 - Yunzi+ User Manual
50h 4Dh 42h 52h
50h 4Dh 43h 4Fh
50h 4Dh 54h 49h
MISCELLANEOUS
Command Data
30h 35h
30h 46h
30h 30h
30h 31h
30h 32h
31h 33h
30h 33h
30h 34h
30h 35h
30h 36h
30h 37h
30h 38h
30h 39h
30h 41h
30h 42h
30h 45h
30h 46h
31h 30h
31h 31h
Anime1
Anime2
Video x.v.Color
Adobe
Stage
Custom1
Custom2
Custom3
Custom4
User 3
User 4
Off
Film1
Film2
Film3
Standard
Cinema1
Cinema2
Description
31h 32h
31h 45h
30h 43h
31h 34h
31h 35h
31h 46h
31h 36h
10 ASCII char.
10 ASCII char.
10 ASCII char.
Custom5
3D film
3D Cinema
3D Video
3D Anime
3D Stage
3D Photo
Set custom name to User1 Picture Mode
Set custom name to User2 Picture Mode
Set custom name to User3 Picture Mode
10 ASCII char.
Set custom name to User4 Picture Mode
37h 33h 43h 36h THX plus - On and Adjust
37h 33h 43h 37h THX plus - Off
37h 33h 43h 38h THX plus - On locked
37h 33h 38h 35h Switch Picture Mode to THX - Bright
37h 33h 38h 36h Switch Picture Mode to THX - Dark
37h 33h 35h 38h ISF - On and Adjust
37h 33h 35h 41h ISF - Off
37h 33h 35h 42h ISF - On locked
37h 33h 36h 34h Switch Picture Mode to ISF - Day
37h 33h 36h 35h Switch Picture Mode to ISF - Night
18 ASCII char.
4 bytes integer
Set Calibrator name - ISF must be “Adjust”
Set contrast to +10 -> 30h 30h 30h 41h
+15 -> 30h 30h 30h 46h
-1 -> 46h 46h 46h 46h
-15 -> 46h 46h 46h 31h
4 bytes integer
4 bytes integer
4 bytes integer same as Contrast same as Contrast same as Contrast
35
MISCELLANEOUS
Function
Aspect Ratio
Anamorphic Modes
Select 3D mode
Command
49h 53h 41h 53h
3D Left / Right phase 49h 53h 33h 50h
2D-3D conversion
49h 4Eh 56h 53h
49h 53h 33h 44h
49h 53h 33h 43h
Command Data
30h
31h
32h
33h
34h
35h
30h
31h
32h
31h
33h
34h
30h
30h
31h
30h
31h
Description
Aspect Ratio set to 4:3
Aspect Ratio set to 16:9
Aspect Ratio set to Zoom
(PC) Auto
(PC) Just
(PC) Full
Turn Off the Anamorphic mode
Anamorphic mode set to Mode A
Anamorphic mode set to Mode B
3D mode set to Auto
3D mode set to Side by Side
3D mode set to Top & Bottom
3D mode is disable (force 2D mode)
Standard phase L/R
Inverse phase R/L
2D to 3D conversion is Off
2D to 3D conversion is On
Lens Control
Function
Lens Shift
Lens Focus
Lens Zoom
Keystone
Intelligent Aperture
Command
49h 4Eh 31h 55h
49h 4Eh 31h 44h
49h 4Eh 31h 52h
49h 4Eh 31h 4Ch
49h 4Eh 31h 46h
49h 4Eh 31h 4Eh
49h 4Eh 31h 57h
49h 4Eh 31h 54h
49h 4Eh 4Bh 56h
50h 4Dh 44h 49h
Lens Memory 52h 43h
Lens Memory Select 49h 4Eh 4Dh 4Ch
Command Data none none none none none none none none
4 bytes integer
30h
31h
Shift the picture upward
Shift the picture downward
Shift the picture to the right
Shift the picture to the left
Focus far
Focus near
Zoom wide
Zoom tele
Vertical Keystone (same as Contrast)
Off
Auto1
Description
32h
31h
...
Auto2
37h 33h 44h 34h Switch between lens memories
30h Select Lens Memory 1
Select Lens Memory 2
39h
10 ASCII char.
10 ASCII char.
Select Lens Memory 10
Set custom name to Lens Memory1
Set custom name to Lens Memory2
Set Memory1 name
Set Memory2 name
49h 4Eh 4Dh 31h
49h 4Eh 4Dh 32h
Set Memory9 name
...
49h 4Eh 4Dh 39h
Set Memory10 name 49h 4Eh 4Dh 41h
Exemples
You want to...
Switch this unit On
10 ASCII char.
10 ASCII char.
Set custom name to Lens Memory9
Set custom name to Lens Memory10
Command to send send: 21h 89h 01h 50h 57h 31h 0Ah receive: 06h 89h 01h 50h 57h 0Ah
36 R699840 - Yunzi+ User Manual
MISCELLANEOUS
You want to...
Switch this unit Off
Change active Input to HDMI2.
Change Lens Memory1 name to
“TV-size” (unused character are filled with space = 20h)
Command to send send: 21h 89h 01h 50h 57h 30h 0Ah receive: 06h 89h 01h 50h 57h 0Ah send: 21h 89h 01h 49h 50h 37h 0Ah or send: 21h 89h 01h 52h 43h 37h 33h 37h 31h 0Ah send: 21h 89h 01h 49h 4Ch 4Dh 31h 0Ah receive: 06h 89h 01h 49h 4Ch 4Dh 31h 0Ah send: 54h 56h 2Dh 73h 69h 7Ah 65h 20h 20h 20h receive: 06h 89h 01h 49h 4Ch 4Dh 31h 0Ah
16.2 LAN protocol
LAN / RJ-45 communication specification
The network settings may have to be modified in the projector’s network menu to match your current LAN network.
• DHCP Client: When set to ON, the projector’s IP address will be automatically set by the DHCP server. on the LAN.
• IP Address: Sets the IP (Internet Protocol) address of the projector. A valid address must be set for this unit.
• Subnet Mask: Sets the Subnet Mask
• Default Gateway: Sets the Default IP Gateway of the projector.
• MAC Address: A 6 byte hex number that uniquely identifies the projector on the LAN. The value is unique to each individual unit on the LAN network.
Sending a LAN Control Command
In order to send a Remote Control compatible command to this unit, you must open a TCP connection on port
20554. and send a command immediately as the connection will be dropped within 5 sec of inactivity. If for any reason you have to change the TCP connection port, you may use the following RS-232c/LAN command.
[4Ch 53 50h 54h] + 4 ASCII chars as new port address in hexa
You want to set TCP port to 10000
Send 10000 as new TCP port value:
10000 is 2710h in hexa, converted in
ASCII characters: 32h 37h 31h 30h
Then, reboot Network module
Command to send send: 21h 89h 01h 4Ch 53h 50h 54h 32h 37h 31h 30h 0Ah receive: 06h 89h 01h 4Ch 53h 0Ah send: 21h 89h 01h 4Ch 53h 52h 53h 0Ah receive: 06h 89h 01h 4Ch 53h 0Ah
`Control Device
1. Openning Connection on port 20554
Projector
2. Projector Ready
(PJ_OK)
3. Command Type
(PJREQ)
5. Command
4. Projector Acknowledge
(PJACK)
6. Projector confirms
After 5sec, connection is closed
LAN communication protocol and timed out
R699840 - Yunzi+ User Manual 37
MISCELLANEOUS
Examples
You want to...
Switch this unit On
Switch Anamorphic to mode A
Command to send
1. open TCP connection
2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh
3. send PJREQ: 50h 4Ah 52h 45h 51h
4. receive PJACK: 50h 4Ah 41h 43h 4Bh
5. send Power On cmd: 21h 89h 01h 52h 43h 37h 33h 30h
35h 0Ah
6. receive confirmation: 06h 89h 01h 52h 43h 0Ah after 5 sec, TCP connection is closed.
1. open TCP connection
2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh
3. send PJREQ: 50h 4Ah 52h 45h 51h
4. receive PJACK: 50h 4Ah 41h 43h 4Bh
5. send Anamorphic A:
21h 89h 01h 49h 4Eh 56h 53h 31h 0Ah
6. receive confirmation: 06h 89h 01h 49h 4Eh 56h 53h 0Ah after 5 sec, TCP connection is closed.
16.3 Infra Red, long hex-pronto compatible RCU
The infrared command must be sent using NEC 5 protocol in ASCII format.
In the following example, Power ON command is 37h 33h 30h 35h, this command has to be converted as ASCII, it becomes 73 05.
To send this command using long hex Pronto compatible, convert the ASCII code as two hexadecimal numbers as follow:
Code A: 73h = 115 (for code B: 63h = 99, replace 115 by 99)
05h = 5
Then program the Pronto RCU using the Device number 115 and Function 5:
Device Code: 115 (0x73) Function: 5 (0x05):
0000 006D 0001 0011 0141 00A0 0014 003C 0014 003C 0014 0014 0014 0014 0014 003C 0014 003C 0014
003C 0014 0014 0014 003C 0014 0014 0014 003C 0014 0014 0014 0014 0014 0014 0014 0014 0014 0014
0014 0336
A complete device/function chart with their corresponding long hex commands is available, ask your dealer if required.
38 R699840 - Yunzi+ User Manual
MISCELLANEOUS
16.4 Specifications
Overview
Overview
The Yunzi+ uses the latest technology developed to provide the ultimate video-projection experience. LCoS
(Liquid Crystal on Silicon) technology based on a reflective principle features an extremely high-definition picture and seamless color gradations.
Emission method
Display panel size
Display Resolution
Contrast ratio
Projection lens
Brightness
Screen size
Distance range
Inputs:
HDMI 1 input
HDMI 2 input
Color Management
LCoS (Reflective Active Matrix Principle)
0.7” LCoS panels
3840 x 2160 pixels (3D video is rendered in 1920 x 1080)
60,000:1, 120,000:1 and 150,000:1
Throw ratio 1.4:1 - 2.8:1 with 2x Zoom
Electronic zoom, focus and shift.
Electronic aperture control (16x steps Aperture)
1300 ANSI Lumens
60” to 250” (Aspect ratio 16:9) from 150cm to 1200cm with HDCP and CEC with HDCP and CEC
Advanced color settings (7-axis: primaries, secondaries and orange)
Video Processing
Light source lamp
Power Requirements
Power Consumption
Unit size (W x D x H)
MPC v2.0 with Detail Enhancement, BG Blur and True-4K rendition.
2x Full HD frames per picture with advanced 1/16 pixel alignment
230W NSH
100V - 240V AC, 50Hz/60Hz
<360W (0.4W in standby mode)
46 x 51 x 22 cm - 18.1" x 20.1" x 8.7" (excluding feet)
Net Weight
Box size (W x D x H)
Gross Weight
14,3 Kg - 31.5 lbs for Yunzi+1
15,1 Kg - 33.3 lbs for Yunzi+2&3
58 x 61 x 41cm - 22.8" x 24.0" x 16.1"
20 Kg - 44.1 lbs for Yunzi+1
21 Kg - 46.3 lbs for Yunzi+2&3
Operation Environment Temperature: 5°C to 35°C (Storage Temperature: -10°C to 60°C)
Humidity: 20% to 80% without condensation
• Design and specifications are subject to change without prior notice.
• Please note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in order to aid comprehension. Images may differ from the actual product.
3-CHIP LCOS SYSTEM
LCoS is the abbreviation of Liquid Crystal on Silicon. The 3-Chip LCoS systems feature dedicated panels for each color channel and render seamless color graduations without any flickering or rainbow effect artifacts
R699840 - Yunzi+ User Manual 39
MISCELLANEOUS
Dimensions
22 cm
8.7”
46 cm
18.1”
51 cm
20.1”
46 cm
18.1”
51 cm
20.1”
40 R699840 - Yunzi+ User Manual
Operating the 3D-Glasses
(2) Power button
Indicating LED (1)
Optical lenses (4)
Indicating LED (1)
(2) Power button
(3) 3-positions button
Optical lenses (4)
(5) micro-USB slot and
rechargeable battery
1. Charging the 3D-Glasses
The 3D-Glasses come with a USB-rechargeable battery (5) that is charged using the USB to micro-USB cable. Connect the cable to the micro-USB slot. The indicating LED (1) will light On red continuously during the charge. The Glasses are fully charged when the indicating LED (1) switches OFF.
2. Turning On your 3D-Glasses
a. Press the Power Button (2) once.
b. The indicating LED (1) will light ON red and the 3D-Glasses are ready to synchronize with the projector.
3. Turning Off your 3D-Glasses
To turn Off the glasses, press the Power Button (2) during 3 seconds until the indicating LED (1) switches off.
4. 3D-Glasses battery power
The battery allows up to 75 hours of continuous power. When the battery power is low, the lenses (4) will flash slowly (1 second) when the 3D-Glass is powered On.
5. How to use the 3-positions button (3)
The 3-positions button (3) is used to select a functionning mode. By default, the glasses are configured to function with 3D pictures. You can select with the 3-positions button to either watch only left pictures on both eyes or only the right pictures on both eyes of the glass.
6. Efficiency
The 3D-Glasses are programmed to automatically stop functionning after 5 minutes of immobilization. To turn them back On, just press the Power Button (2) once.
42 R699840 - Yunzi+ User Manual
advertisement
