Formax FD 4170 Operator Manual

FD 4170
Cut Sheet Burster
4/2010
OPERATOR MANUAL FIRST EDITION
TABLE OF CONTENTS
TOPIC
PAGE
SPECIFICATIONS
1
UNPACKING & SET-UP
1
INPUT SIDE
2
OUTPUT SIDE
3
OUTPUT CONVEYOR (OPTIONAL)
3
CONTROL PANEL
4
POWERING UP
4
ADJUSTING PROCESSING SPEED
4
LCD DISPLAYS FOR SET-UP & OPERATION
5
STEPS OF SET-UP & OPERATION
6
MANUAL SETTING
7
EXAMPLES OF CUT SIZES
7
LOADING PAPER
8
PREPARATION BEFORE OPERATION
9
COUNTER DISPLAY & RESET
10
PRESET MODE
10
PRESET TABLES
11
PRESET SELECTION SETTING
11
TO INPUT FIXED PRESET
12
TO CANCEL FIXED PRESET
12
TO INPUT FREE SIZE PRESET
13
TO CANCEL FREE SIZE PRESET
13
OPTIONAL CONVEYOR OPERATION
14
TROUBLE-SHOOTING
14
ERROR DISPLAY GUIDE
15
CLEARING ERROR MESSAGES
16 - 21
SPECIFICATIONS
Speed:
5-level speed adjustment: 42, 64, 89, 114, 140 sheets/minute
Feed Tray Capacity:
Up to 400 sheets
Paper Size:
5” - 17” H x 4” - 11” W
Paper must not have staples, clips, adhesive or holes.
Paper Weight:
13# bond - 110# index (58 - 175 gsm)
Min./Max. Burst Length:
2.5” - 9.9”
Dimensions:
32” L x 9” H x 16” D
Weight:
56 lbs.
Voltage:
120V, 60 Hz
UNPACKING &
SET-UP
■
Before Using Machine
■ Preparation
Preparation Before Using Machine
Check package for shipping damage. If there is shipping damage, do not discard the box.
1. Remove the setscrew from the right side of the
1. Remove
the setscrew
from
the
right
the
stacker,
insert
the
axis
intoside
theof
holes
1. Facing the output side,paper
remove
the and
setscrew
from
the
paper
stacker,
and
insert
the
axis
into
the
holes
the machine
frame the
on the
both
sides.
right side of the paper of
stacker,
and insert
axis
into
of
the install
machine
frame
on
the
both
Then
theboth
paper
stacker
withsides.
the setscrew
the holes of the machine
frame
on
sides.
Then
Then
install the paper stacker with the setscrew
removed.
install the paper stacker
with
the
setscrew
removed.
removed.
2. Remove the thumb screws in the circles and
Remove
thumb
screws
inattach
the
circles
and
2. Remove the thumb2.screws
(inthe
the
circles)
and
attach
the
columns
on
the
right
and
left hooks,
attach
the
columns
on
the
right
and
left
hooks,
the columns on the right
and left
hooks,
then fasten the
and fasten
thumb
screws.
and fasten thumb screws.
thumb screws.
4. Remove the screw in the circle in the right picture
3. Remove the screw4.(see
circled
area, right)
install
Remove
theand
circle
in the
right picture
and
installthe
thescrew
paperinholding
plate
(attachment).
the paper holding plate
attachment.
Setholding
the paper
stopand
install
the
paper
plate
(attachment).
Set the paper stopper and the paper guides as
per and paper guidesSet
asthe
shown
instopper
the picture.
paper
and the paper guides as
shown
in
the picture.
shown in the picture.
5. Insert the edge of the support tray into the right
5. and
Insert
edge ofofthe
tray into
right
leftthe
columns
thesupport
paper feed
part the
of the
main
and
left
columns
of
the
paper
feed
part
of
the
main
body.
Then,
set
the
support
tray
downwards.
4. Insert the edge of thebody.
support
trayset
into
right tray
anddownwards.
left
Then,
thethe
support
columns of the paper infeed tray. Then set the support
tray downward.
1
enihcaM g
enihcaM g
eht fo edis t
seloh eht ot
eht fo ed.sisedt i
sweelorchsetehst oethn
.sedi
wercstes eht
dna selc
,skooh tfe
dna selcr
,skooh tfel
erutcip thgir
.)tnemhcatt
erutscaipstehdgiiur ge
.)tnemhcatt
sa sediug r
thgir eht ot
niam eht fo tr
th.gsidrreahwtnow
t
niam eht fo tra
.sdrawnw
■ Part Names and Their Functions
INPUT SIDE
● Appearance (front side)
3
5
4
7
10
1
6
8
9
2
11
No.
Number
1 1
2 2
3
3
4
5 4
6 5
6
7
8 7
9
10
8
11 9
10
11
Name
Description
Paper
PaperFeed
feedTray
tray
Support
SupportTray
tray
Paper Feed Guides
Function
Function
Paper to be burst is set here.
OpenPaper
this tray
prior
to operating
to support
paper.
to be
burst
is set here.
Open this
tray while operation.
Align and center paper according to width.
Paper feed guide
Sets paper to arbitrary position according to paper width.
Safety Cover
Must be closed during operation. Burster will not operate with cover open.
Always close this cover during operation. Machine does not
SafetyFeed
cover
Paper
Pressure
Adjusts
paperwith
feeditpressure
operate
open. according to paper thickness. Standard setAdjusting Lever
ting is “Normal Paper.”
Paper feed pressure
Adjusts paper feed pressure according to paper thickness.
Paper
Feedlever
Tray
Moves
the paper
feed
up and down.
adjusting
Normal
setting
is tray
“Standard”.
Up/Down
Lever
Paper feed
tray up/down
Moves the paper feed tray up and down.
lever Feed Rubber Roller Feeds paper into the bursting area.
Paper
PaperSwitch
feed rubber roller Toggles
Feeds
papers
the
inside
the machine.
Power
between
ONto(I)
and
OFFof
(O).
Power Cord Inlet
InsertPower
poweriscord
here.
turned
on by pressing “I” side of the switch.
Power switch
Power
is
turned
pressing
“O” side of the switch.
Control Panel
Refer to Control Paneloff
onby
page
4.
Inlet Breaker
provided
power
cord.
Circuit
ShutsInsert
downthe
machine
in case
of overload.
Operation panel
Refer to “Operation Panel” on page 11.
Cuts off the power in the meanwhile when excessive load is
Breaker
given to the machine.
V
9
2
● Appearance (exit side)
OUPUT SIDE
2
3
1
Number
No.
1
2
3
1
2
Description
Function
Stacker
Burst forms stack here upon exiting.
Name
Paper Guide
Stacker
Paper Stopper
Paper guide
3
Paper stopper
Function
Should be set according to the width of the burst forms.
● Option
Receives
ejected paper.
Should be set according to the length of the burst forms.
Set according to the width of ejected paper.
Set according to the length of ejected paper.
Conveyer unit
OUTPUT CONVEYOR (optional)
With the optional Output Conveyor, burst forms can be
easily removed while the burster is still operating.
V
10
3
1. Connect the ‘female plug’ of the power cord to
● Operation
CONTROL
PANELPanel
the ‘inlet’.
2. Connect the ‘male plug’ of the power cord to
the ‘outlet’.
1
2
3
4
Number
1
2
3
4
5
Description
“+” Button
Decrease Speed Button
2 Vertical:
+ key2.5-17inch
Increase Speed Button
3 Width:
Slow 3-11inch
down key
JOG Button
7
Use to decrease cut size
on LCD display
Function
Name
1 Paper
- keysize
6
Function
■
Usable Paper
“-” Button
No.
5
Use to increase cut size on LCD display
Value (cut size) on the LCD display is decremented.
Decreases processing speed, also used to select Presets
Value (cut size) on the LCD display is incremented.
Increases processing speed, also used to select Presets
Processing speed gets slow.
Press this to process one sheet of paper
Processing speed gets fast.
4 Speed up key
thickness
3. Press
“I” side
of the power switch.
6 thePaper
START
Button
Press to start operation. NOTE: This button is inoperative when an
The error
machine
runs slowlyorwhile
this key
is the
depressed.
5 58-157gsm
is displayed,
no paper
is in
infeed tray.
The power
toJOG
the key
machine turns on.
7
Press
to start
operation.
Press
to stop
operation. NOTE: When this button is pressed after a
* This
key isjam
inoperative
when
error is will
displayed
or no paper is
Paper stack capacity
paper
is cleared,
thean
indicator
be reset.
set.
350 sheets (thickness: 58gsm)
Presson
to stop
7 Capacity
STOP/C
key
may
change depending
paperoperation.
alignment or curl.
6 STOP/C
STARTButton
key
[ NOTES ]
When this key is pressed after the cause of paper JAM is solved
while the machine stops due to paper jam, the indicator will be
reset.
TheUP
following paper cannot be used.
POWERING
1.
2.
3.
4.
* Paper with holes for filing
* Paper with staples and/or clips
Plug power cord into inlet on Infeed Side of burster.
Paperwith
with appropriate
curl or creasepower capacity.
Plug into wall* outlet
4.
When the*power
is turned
Display when the power is on
Paper with
carbonon, “HE110” appears
Press
power
switch
to
the
“I”
position.
on the LCD.
* Paper with cut and paste
When the power
is turned
on,or
“HEll0”
appears
in to
the
* Paper
with glue
adhesive
applied
sticker or tuck and so on.
LCD area of the control panel.
To turn off power, press switch to “O” position.
■Turning OFF the Power
■side
Adjusting
Processing
Speed
Press the “O”
of the power
switch.
The power to the machine turns off.
ADJUSTING
PROCESSING
SPEED
5 speed
levels are adjusted by pressing
the speed key.
To adjust between speed levels, press either of the speed
buttons. Speeds include 42, 64, 89, 114, or 140 sheets per
minute.
Gets faster by pressing the speed up key. 11
To decrease speed, press the left SPEED button.
To increase speed, press the right SPEED button.
18
Gets slower by pressing the slow down key.
4
V
■
Display
for
Operation
and
Setting
■
Display
for
Operation
and
Setting
■
Display
for
Operation
and
Setting
■Display
Displayfor
forOperation
Operationand
andSetting
Setting
■
■
Display
for
Operation
and
Setting
●
for
start
●■Display
Display
forfor
start
LCD
DISPLAYS
FOR SET-UP
AND OPERATION
Display
Operation
and Setting
Display
for
start
●Display
Display
forstart
start
●●●
for
Display
for
start
when the power is turned on.
● Display
Display for
for Start
start Appears
Appears when the power is turned on.
Appears
when
the
power
turned
on.
Appearswhen
whenthe
thepower
powerisis
isturned
turnedon.
on.
Appears
Appears
when
the
power
is
turned
on.
Appears when the power is turned on.
Appears when the power is turned on.
●
● Display
Display for
for stand-by
stand-by status
status
Display
for
stand-by
status
●Display
Display
for
stand-by
status
●●●
Displayfor
forstand-by
Stand-bystatus
Status
Display
for
stand-by
status
Appears
when
Manual
Setting
is selected.
● Display for stand-by
status
Appears
when
Manual
Setting
is selected.
Appears
when
Manual
Setting
is selected.
Appears
when
Manual
Setting
selected.
Appearswhen
whenManual
ManualSetting
Settingisis
isselected.
selected.
Appears
Appears
when
Manual
Setting
is
selected.
Appearswhen
whenPreset
Manual
Setting is
selected.
Appears
Selection
Setting
is selected. (Fixed Preset
Appears when Preset Selection Setting is selected. (Fixed Preset
Appears
when
Preset
Selection
Setting
is
selected.
(Fixed
Preset
Appears
when
Preset
Selection
Setting
isselected.
selected.
(Fixed
Preset
Appears
when
Preset
Selection
Setting
is chosen
(Fixed
Preset Selection).
Selection)
Appears
when
Preset
Selection
Setting
is
(Fixed
Preset
Appears
when
Preset
Selection
Setting
is
selected.
(Fixed
Preset
Selection)
Selection)
Selection)
Displays
pre-set
fixed
cut
size.
Displays
preset
fixed
cut
size.
Selection)
Selection)
Displays
preset
fixed cut
size. Setting is selected. (Fixed Preset
Appears
when
Preset
Selection
Displays
preset
fixed
cut
size.
Displayspreset
presetfixed
fixedcut
cut
size.
Displays
size.
Displays
preset
fixed
cut
size.
Selection)
Appears
when Preset Selection Setting is selected. (Free Size Preset
Appears
when
Preset
Selection
Setting
is selected.
(Free(Free
Size Size
Preset
Displays
preset
fixed
cut
size.
Appears
when
Preset
Selection
Setting
is chosen
Preset Selection).
Appears
when
Preset
Selection
Setting
selected.
(Free
Size
Preset
Appears
when
Preset
Selection
Setting
isselected.
selected.
(FreeSize
SizePreset
Preset
Selection)
Appears
when
Preset
Selection
Setting
isis
(Free
Appears
when
Preset
Selection
Setting
is
selected.
(Free
Size
Preset
Selection)
Displays
pre-set
cut
size.
Selection)
Selection)
Displays
preset
cut
size.
Selection)
Selection)
Displays
preset
cut size.
Appears
when
Preset
Selection Setting is selected. (Free Size Preset
Displays
preset
cut
size.
Displayspreset
presetcut
cutsize.
size.
Displays
Displays
preset
cut
size.
Selection)
Displays counter (appears by pressing the STOP/C button).
Displayscounter.
preset cut
size. by pressing the STOP/C key.)
Displays
(appears
Displays counter. (appears by pressing the STOP/C key.)
Displays
counter.
(appears
by
pressing
the
STOP/C
key.)
Displayscounter.
counter.(appears
(appearsby
bypressing
pressingthe
theSTOP/C
STOP/Ckey.)
key.)
Displays
Displays
counter.
(appears
by
pressing
the
STOP/C
key.)
Displays
cut
speed,
Speed
1 (appears
- 5 (appears
by pressing
one of
the SPEED buttons).
Displays
counter.
(appears
by- pressing
theby
STOP/C
key.)
Displays
cut
speed.
: Speed
1
5
pressing
the speed
key.)
Displays cut speed. : Speed 1 - 5 (appears by pressing the speed key.)
Displays
cut
speed.
Speed
(appears
by
pressing
the
speed
key.)
Displayscut
cutspeed.
speed.::::Speed
Speed111
1----555
5(appears
(appearsby
bypressing
pressingthe
thespeed
speedkey.)
key.)
Displays
Displays
cut
speed.
Speed
(appears
by
pressing
the
speed
key.)
Displaysindependent
cut speed. : operation
Speed 1 -of
5 (appears
by pressing
the speed
key.)
Displays
optional
unit.
(while
pressing
thepressing
Displays
independent
operation
of optional
unit (appears
the
Displays
independent
operation
of optional
unit. (while
pressingby
the
Displays
independent
operation
of
optional
unit.
(while
pressing
the
Displays
independent
operation
ofoptional
optional
unit.(while
(whilepressing
pressingthe
the
STOP/C
key
and the
JOG
keybutton
simultaneously.
Displays
independent
operation
of
unit.
Displays
independent
operation
of
optional
unit.
(while
pressing
the
STOP/C
button
and
JOG
simultaneously).
STOP/C
key
and the
JOG
key simultaneously.
Display for
for preset
preset
mode
STOP/C
key
and
the
JOG
key
simultaneously.
STOP/C
keyand
andthe
theJOG
JOGkey
keysimultaneously.
simultaneously.
STOP/C
key
●● Display
mode
STOP/C
key
and
the
JOG
key
simultaneously.
Displays independent operation of optional unit. (while pressing the
STOP/C key and the JOG key simultaneously.
● Display for preset
modewhen preset registration/cancel is executed. (Fixed Preset
Appears
Appears
● Display
for preset
modewhen preset registration/cancel is executed. (Fixed Preset
Display
for Pre-Set
Mode
Display for Bursting
Registration)
Registration)
Displays
fixed
cut
sizeregistration/cancel
for preset
preset registration/cancel.
registration/cancel.
Appears
whenpreset
preset
is executed.
(Fixed
Preset
Displays
fixed
cut
size
for
Appears
when
registration/cancel
is executed
(Fixed(Fixed
Preset Preset
Registration).
Appears
when
preset
registration/cancel
is executed.
Registration)
Displays fixed cut size for preset registration/cancel.
Registration)
Appears
when
preset
registration/cancel
is executed.
executed. (Free
(Free size
size preset
preset
Displays
fixed cut
size registration/cancel
for preset registration/cancel.
Appears
when
preset
is
Displays
fixed
cut
size
for
preset
registration/cancel.
registration)
registration)
Appears when
preset
registration/cancel
is executed
(Free Preset
Registration).
Displays
fixed
cut
size
for
preset registration/cancel.
registration/cancel.
Appears
when
preset
registration/cancel
is executed.
(Free
size preset
Displays
fixed
cut
size
for
preset
Displays
fixed
cut
size
for
preset
registration/cancel.
Appears
when
preset
registration/cancel
is
executed.
(Free
size preset
registration)
registration)
Displays fixed cut size for preset registration/cancel.
Displays fixed cut size for preset registration/cancel.
Display for
for bursting
bursting
●● Display
Counter
● Display for bursting
Displays counter.
counter.
Displays
● Display for bursting
13
13
Displays counter.
13
13
13
Bursting
speed:
Speed
1 -5 (appears
pressing
one of
SPEED the
buttons).
Displays
counter.
Displays bursting
bursting13
speed.
Speed 11by-- 5
5 (displayed
(displayed
bythe
pressing
speed
Displays
speed.
:: Speed
by
pressing
the speed
13
key)
key)
Displays bursting speed. : Speed 1 - 5 (displayed by pressing the speed
Displays bursting speed. : key)
Speed 1 - 5 (displayed by pressing the speed
key)
Refer to
to “■
“■ Error
Error Display”
Display” on
on page
page 31.
31.
** Refer
* Refer to “■ Error Display” on page 31.
* Refer to “■ Error Display” on page 31.
5
STEPS OF SETUP AND OPERATION
■ Procedure of Use
Unpacking
& Set-up
1) (p.17)
■ Preparation
Before
Using(page
Machine
(page 4)
■ Turning On the Power (p.18)
(pg
7) Manual Setting: Standard mode inputting cut size on a case-by-case basis
(p.19)
(pg
11) Preset Selection Setting: Convenient function registering frequently used cut size
(p.24)
in advance and easily retrieving the registered cut size
Manual Setting and Preset Selection Setting cannot be selected simultaneously.
10) Preset Selection Setting is automatically
When cut size is registered in Preset Mode (pg
(p.25),
selected.
When you desire to return the setting to manual setting, cancel all preset registrations.
Refer to “■ Fixed Preset Registration/Cancel” or “■ Free Size Preset Registration/Cancel”
on pages 27
- 28 for canceling preset registration.
12-13
Register desired size in
Preset Mode. (p.25)
(pg 10)
(pg 7)
Manual Setting (p.19)
(pg 11)
Preset Selection Setting (p.24)
Loading
Paper
(page
Setting
Paper
(p.21)8)
(pages 1-4)
Preparation Before Operation (Setting paper stacker, Speed adjustment) (p.22)
Start operation.
6
Manual setting is standard mode that each cut size is input on a case-by-case basis.
MANUAL SETTING
[ NOTES ]
When cut
is registered
as Preset
Setting,
Selectionfor
Setting”
is automatically selected.
Manual Setting
is a size
standard
mode in which
each cut
size is“Preset
input individually
each project.
“Manual Setting” and “Preset Selection Setting” cannot be selected simultaneously.
NOTE: When
cutall
size
is input
as Preset Setting,
“Preset
Selection
Setting”
is automatically
selected.
“Manual Setting” and
Cancel
preset
registrations
to change
“Preset
Selection
Setting”
to “Manual
Setting”.
“Preset Selection Setting” cannot be selected simultaneously. Cancel all preset inputs to change “Preset Selection Set* Refer to ”■ Fixed Preset Registration/Cancel” or “■ Free Size Preset Registration/Cancel”
ting” to “Manual Setting.” Refer to Fixed Preset Input/Cancel or Free Size Preset Input/Cancel on pages 12-13 for more
on pages 27 - 28 for canceling preset registration.
information.
1. Turn on power. Machine is in stand-by mode. Previous cut size will be shown in LCD display.
1.cut
Turn
on the power to make the machine stand-by status.
2. Input
size.
* Cut
size previously
set isby
displayed.
The value
of each
digit is increased
pressing the “+” button, decreased by pressing the “-” button.
Refer to the Cut Size Chart below. Abbreviate the value for cut size to the first decimal place.
NOTE:
Settingcut
range
2. Input
size.is 0, 2.5-9.9 inches. When cut size is set to 0, the paper is fed without bursting.
3. Refer toValue
Preparation
Before
on page
of each
digit Operation
is incremented
by9.pressing the + key.
Value of each digit is decremented by pressing the - key.
* Refer to “■ Cut Size Setting Example“ on the following page.
* Truncate the value for cut size to first decimal place.
■ Cut Size Setting Example
EXAMPLES
OF CUT SIZES
[ REFERENCE ]
Truncate
the0,value
cutinches
size to first decimal place.
* Setting
range:
2.5 -for
9.9
When setting
cut size,
abbreviate
to
the first decimal place.
* When cut size is 0, the paper is just fed without bursting.
● Setting example
3. Execute “■ Preparation Before Operation“ on page 22 according to the desired set value.
Paper size
8.5” x 11” Vertical
8.5” x 11” Horizontal
8.5” x 14” Vertical
11” x 17” Horizontal
Number of
cuts
Finished size (inch)
Set value of cut size
(Truncate to first decimal
place)
2
8.5” x 5.5”
5.5
3
8.5” x 3.67”
3.6
4
8.5” x 2.75”
2.7
2
11” x 4.25"
4.2
3
11” x 2.83”
2.8
2
8.5” x 7.0”
7.0
3
8.5” x 4.67”
4.6
4
8.5” x 3.5”
3.5
5
8.5” x 2.8”
2.8
2
11” x 8.5”
8.5
3
11” x 5.67”
5.6
4
11” x 4.25”
4.2
5
11” x 3.4”
3.4
6
11” x 2.83”
19
2.8
7
■
Paper
LOADING
■ Setting
SettingPAPER
Paper
1. Fan the air into sheets by riffling.
Fanthethe
air into
sheetswhich
by riffling.
1. 1.Fan
sheets
to loosen,
will decrease static
electricity and reduce the chance of a paper jam or
[ misfeed.
IMPORTANT ]
[ IMPORTANT ]
Loosing papers can reduce static electricity on the
Loosing papers can reduce static electricity on the
paper and prevent from paper jam or misfeed.
paper and prevent from paper jam or misfeed.
* Refer to “■ Usable Paper“ on page 15.
* Refer to “■ Usable Paper“ on page 15.
2. Lower the up/down lever for the paper feed tray
Lower
up/down
lever
forpaper
the paper
feedand
tray
2. 2.Lower
thethe
up/down
lever
on the
feed tray
and place
theon
paper
to be
burstthe
onpaper
the paper
feed
place
the
paper
the
tray.
Adjust
feed
and place the paper to be burst on the paper feed
tray. on both sides, then tighten the setscrews.
guides
tray.
Readjust the paper feed guides at both sides
Readjust the paper feed guides at both sides
without pressing the paper to be burst.
without pressing the paper to be burst.
Then, tighten the setscrew.
Then, tighten the setscrew.
Adjust
the
paper
feed
pressure
to the thickness
3. 3.Adjust
the
paper
feed
pressure
adjustment
lever to theof
3. Adjust
the
paper
feed
pressure
to the thickness
of
thickness
the paper.
it is set to “NORMAL.”
paper. of
Usually
it is Usually
set to “NORMAL”
position.
paper. Usually it is set to “NORMAL” position.
If the paper cannot be fed, set the pressure adjust lever
“HEAVY.”
●toWhen
paper cannot be fed, set the paper feed
●IfWhen
cannot besetfed,
thetopaper
feed
doublepaper
feeding
theset
lever
“LIGHT.”
pressure
adjustoccurs,
lever to “HEAVY”
position.
pressure adjust lever to “HEAVY” position.
● When double feed occurs, set the paper feed
● When double feed occurs, set the paper feed
pressure adjust lever to “LIGHT”.
pressure adjust lever to “LIGHT”.
4. Raise the up/down lever.
Raise
up/down
lever.
4. 4.Raise
thethe
up/down
lever.
8
21
PREPARATION BEFORE OPERATION
1.
■ Preparation
Before Operation
■■Preparation
Before
Operation
Preparation
Before
Operation
1．Set
bursting speed.
■speed.
Preparation
Before Operation
1．Set
bursting
1．Set
bursting
speed.
Set
bursting
speed
Setting
Speed
1 - LCD
5 while the machine
5. Speed
Counter
on the
Setting
range:
1range:
-appears
5
1．Set
bursting
speed.
Setting
range:
Speed
1-5
Ex.: Speed
1 Ex.:1Speed 1
Number
of
sheet processed
Ex.: Speed
is working.
Number
of sheet
processed
Number
of
sheets
Number
of
sheet
processed
Setting
Speed 1[sheet/min.]
-5
Speedrange:
Preparation
Before
Operation
Speed
[sheet/min.]
Ex.: Speed 1
processed
Speed
[sheet/min.]
Number
of
sheet
processed
(A4
vertical)
[ REFERENCE
]
(A4
vertical)
Preparation
Before
Operation
(sheets
per
minute)
(A4speed.
vertical)[sheet/min.]
bursting
/ JOG
40
The1Speed
value
on the
as
1 deepS :.xE
1 / JOG 1．Set
40counter is incremented
1 / JOG 1．Set
40 (A4 vertical)
2
60
[0→1→
.···
9999].
bursting
speed.
2
Setting range:60Speed 1 - 5
/ JOG
40
2
The1counter
returns60
to “0” after84
“9999”.
Ex.: Speed 1
3
3
processed
Setting
range:84Number
Speed 1 of
- 5sheet
2
60
3
84
4
107
Ex.: Speed 1
4
107Number[sheet/min.]
Speed
of sheet
3
84 processed
4
107
5
130
5
130
(A4
vertical)
Speed
[sheet/min.]
4
107
5
130
1 / JOG
40
(A4 vertical)
2．Feed
the paper
pressing
2．Feed the paper
by5pressing
theby
JOG
key130
tothe JOG key to 22
2
60
1
/
JOG
perform
test
cut.
2．Feed
the paper
key to
perform test
cut. by pressing the JOG 40
2．Feed
the
by
JOGthe
keycut
to size
*cut.
Ifnot
test
cutpaper
doescheck
notpressing
succeed,
check
3
84
2
60the
* Ifperform
test cut test
does
succeed,
the cut
size
setting.
perform
test
cut.
4
107
2. Feed setting.
paper
pressing
thesucceed,
JOG button
to perform
a
84 cut size
* If testbycut
does3 not
check
the
* Ifincorrect,
test cut does
notcut
succeed,
check the cut size
test cut.setting.
If test cut is
check
size
5
130
4
107setting.
setting.
5
130
2．Feed the paper by pressing the JOG key to
perform
cut.by pressing the JOG key to
2．Feed
thetest
paper
*
If
test
cut
does
not succeed,
check
the guides
cut size
perform
test
cut.
3．Adjust
the
paper
and the
paper
3．Adjust the paper
stopper
and
thestopper
paper guides
setting.
*wider
If testbycut
does
not
succeed,
check
the
cut size
approx.
0.12 inch
than
burst
wider by approx.
0.12
inch
than
burst
paper
with
a paper with a
3．Adjust
the
paper
stopper
and
the
paper
guides
setting.
3．Adjust
hand. the paper stopper and the paper guides
hand.
wider by approx.
inch than
paper
withpaper
a with a
wider0.12
by approx.
0.12burst
inch than
burst
3. On output
side, adjust
paper
stopper
and
paper
guides
hand.
hand.
to approximately 0.12 inch wider than the burst paper.
3．Adjust the paper stopper and the paper guides
wider by
approx.
0.12 inchand
than
paper
with a
3．Adjust
the
paper stopper
theburst
paper
guides
hand.
wider by approx. 0.12 inch than burst paper with a
hand.
4. Start
machine
pressing
4. Start the machine
bythe
pressing
theby
START
key.the START key.
*
The
machine
automatically
stops after processing.
* The machine automatically stops after processing.
4. Start the
pressing
START key.
4. Start the machine
bymachine
pressingbythe
STARTthe
key.
*
The
machine
automatically
stops
after processing.
* The machine automatically stops after processing.
noit
■
■
the machine
by pressing
START key.
4. Start operation 4.
byStart
pressing
the START
button.the
Machine
The
machine
automatically
after processing.
4. *Start
the
machine
by pressingstops
the START
key.
automatically stops
after
processing.
* The machine automatically stops after processing.
5. Counter
on the
the machine
LCD while the machine
5. Counter appears
on theappears
LCD while
is
working.
is working.
5. Counter appears on the LCD while the machine
5. Counter appears
on the LCD
while the machine
is working.
]
[ REFERENCE[ REFERENCE
]
is working.The
value on
the counter isasincremented as
The value on the counter
is incremented
[
REFERENCE
]
[0→1→
.···
9999].
[0→1→ .··· 9999].
5.
Counter
appears
on
theisafter
LCD
while theas
machine
[
REFERENCE
]
The
value on
the counter
incremented
counter
returns
to “0”
“9999”.
The counter returns
to “0” after “9999”.
is
working.
5.appear
Counter
on
the LCD
5. TheThe
counter
inappears
theisLCD
display
during
.···
9999].
valuewill
on[0→1→
the
counter
incremented
aswhile the machine
is working.
processing.
The
value
of thereturns
counter
is from
- 9999.
The
counter
to “0”
after 0
“9999”.
[0→1→ .···
9999].
[ REFERENCE
] 0.
After
9999,
counter
will
return
to
The counter returns to “0” after “9999”.
The
value on the] counter is incremented as
[ REFERENCE
22
22
[0→1→
.···on
9999].
The value
the counter is incremented as
The
counter
returns to “0” after “9999”.
[0→1→
.··· 9999].
22
The counter returns to “0” after “9999”.
22
9
22
22
des
ot yek
ezis tuc e
sediug re
a htiw repap
.yek TR
.gnissecorp r
enihcam
sa
22
4. Start the machine by pressing the START key.
* The machine automatically stops after processing.
COUNTER DISPLAY AND RESET
Counter Display
1. To display the number of cut sheets after a previous reset, press and hold the STOP/C button in stand-by mode.
2. The counter display disappears by releasing the STOP/C button.
Counter Reset
5. Counter appears on the LCD while the machine
is working.
■ Manual Setting
To reset the counter,
press both the] STOP/C button and
[ REFERENCE
the “-” button and hold
three
or is
more.
Thefor
value
on seconds
the counter
incremented as
Manual[0→1→
setting.···
is standard
mode
that each cut size is input on a case-by-case basis.
9999].
The counter returns to “0” after “9999”.
[ NOTES ]
When cut size is registered as Preset Setting, “Preset Selection Setting” is automatically selected.
“Manual Setting” and “Preset Selection Setting” cannot be selected simultaneously.
Cancel all preset registrations to change “Preset Selection
Setting” to “Manual Setting”.
22
PRESET* Refer
MODE
to ”■ Fixed Preset Registration/Cancel” or “■ Free Size Preset Registration/Cancel”
on pages 27 - 28 for canceling preset registration.
Preset Mode is different from Standard Mode and can register cut size selected in Preset Selection Setting in advance.
Turn onMode
the power to make the machine stand-by status.
Registering1.Preset
* Cut size previously set is displayed.
2. Input cut size.
1. Turn on power
while
STOP/C button
on the control
Value
of pressing
each digitthe
is incremented
by pressing
the + panel.
key.
Value of each digit is decremented by pressing the - key.
* Refer to “■ Cut Size Setting Example“ on the following page.
* Truncate
value
forspeed
cut size
decimal
2. To select Preset
# pressthe
either
the
up to
orfirst
down
button.place.
See Preset Table on the following page.
Speed up button: Increases the value of the Preset number.
[ REFERENCE ]
* Setting range: 0, 2.5 - 9.9 inches
* When cut size is 0, the paper is just fed without bursting.
Speed down button: Decreases the value of the Preset number.
Execute
“■ Preparation
Beforeand
Operation“
22 according
to the desired set value.
3. Preset is3.
saved
by pressing
the “+” button
cancelledon
bypage
pressing
the “-” button.
Preset Setting is not available at factory setting.
4. Save/Cancel information is stored by pressing the JOG button.
5. To quit Preset Mode, turn power off and on, or press the STOP/C button for more than 3 seconds. This will make the
Preset Setting available.
10
■PRESET
Preset Table
TABLES
“11-2”
1
“11-3”
2
“11-4”
3
“14-2”
4
“14-3”
5
“14-4”
Paper size
8.5” x 11” Vertical
8.5” x 14” Vertical
Number
of cuts
Finished size
(inch)
Cut size
2
8.5” x 5.5”
5.5
3
8.5” x 3.67”
3.6
4
8.5” x 2.75”
2.7
2
8.5” x 7.0”
7.0
3
8.5” x 4.67”
4.6
4
8.5” x 3.5”
3.5
6
“14-5”
5
8.5” x 2.8”
2.8
7
“17-2”
2
11” x 8.5”
8.5
8
“17-3”
3
11” x 5.67”
5.6
9
“17-4”
4
11” x 4.25”
4.2
5
11” x 3.4”
3.4
6
11” x 2.83”
2.8
0
-----
0
11” x 17” Vertical
10 “17-5”
11
“17-6”
12 “PASS”
“17-2”
2
11” x 8.5”
8.5
“17-3”
3
11” x 5.67”
5.6
9
“17-4”
-----
z
Free size preset list
No.
Display
11” x 17” Vertical
4
11” x 4.25”
4.2
10 “17-5”
5
11” x 3.4”
3.4
11
6
11” x 2.83”
2.8
0
-----
0
“17-6”
12 “PASS”
z
Fixed preset list
No.
Display
0
7
8
-----
z
Free size preset list
No.
Display
Cut size input range
13 “0. *.*”
14 “1. *.*”
15 “2. *.*”
16 “3. *.*”
17 “4. *.*”
18 “5. *.*”
0, 2.5 - 9.9 inches
When “0” is displayed, preset is cancelled.
19 “6. *.*”
20 “7. *.*”
21 “8. *.*”
22 “9. *.*”
■ Preset Selection Setting
This function can register frequently used cut size in advan
easily when needed.
* Refer to “■ Preset Mode“ on the following page to register
* Preset Selection Setting is available only in Preset Mode.
Cut size input range
PRESET
SELECTION SETTING
13 “0. *.*”
14 “1. *.*”
15 “2. *.*”
Frequently
used cut sizes can be stored into memory and recalled easily. Preset Selection Setting is available
only in
26
16 “3. *.*”
Preset
Mode.
17 “4. *.*”
18 “5. *.*”
0, 2.5 - 9.9 inches
When “0” is displayed, preset is cancelled.
[ NOTES ]
NOTE:
automatically
selected.
19 “6. *.*”When cut size is already registered, Preset Selection Setting
Wheniscut
size is already
registered, Preset Selection Setting
20 “7. *.*”Manual Setting and Preset Selection Setting cannot be selected simultaneously.
Manual Setting and Preset Selection Setting cannot be selec
21 “8. *.*”Cancel all preset registrations in order to change to Manual Setting.
Cancel all preset registrations to change the setting to Manu
* Refer to “■ Fixed Preset Registration/Cancel“ or “■ Free
pages 27 - 28 to cancel preset registration.
22 “9. *.*”
1. Turn on power. Machine will be in stand-by mode.
2. To choose Fixed Preset or Free Size Preset, use the
“+” and “-” buttons.
+ button increases the Preset #
- button decreases the Preset
26 #
(Non-preset number is not displayed.)
When the machine is turned off and turned on again,
the previous setting is displayed.
1. Turn on the power to make the machine stand-by status.
3. Select Preset cut size and follow “Preparation Before
Operation” steps on page 9.
2. Select registered Fixed Preset or Free Size Preset using t
[ REFERENCE ]
+ key: Value of preset no. is incremented by pressing this
– key: Value of preset no. is decremented by pressing this
* Non-preset no. is not displayed.
[ REFERENCE ]
Previous display appears when the power to the machin
and turned on again.
11
3. Select preset cut size and follow “■ Preparation Before O
INPUT FIXED
PRESET
■TO
■Fixed
FixedPreset
PresetRegistration/Cancel
Registration/Cancel
Example:
No. 0
8.5” x 11”
z
Fixed
Preset
Registration
z
Fixed
Preset
Registration
1.
Vertical
2-cut
Select preset No. 0 by pressing the speed up or speed down button.
Example:
No.0
x 11”
2-cut
Example:
No.0 8.5”
8.5”
xbefore
11” Vertical
Vertical
2-cut
* The display
blinks
being accepted.
1.1.
Select
preset
No.0
byby
pressing
the
speed up key and the slow down key.
Select
preset
No.0
pressing
the
2. Press the “+” button to accept the preset.speed up key and the slow down key.
* The
display
blinks
before
registration.
display
blinks
before
registration.
To* The
add more
presets,
repeat
steps
1 and 2.
2.2.
Press
the
+
key
to
register
preset.
Press the + key to register preset.
Lights
upup
Blinking
Blinking
Lights
* When
you
desire
toto
continue
registration,
repeat
the
above
procedures
1 and
2.2.
* When
you
desire
continue
registration,
repeat
the
above
procedures
1 and
3.
Fixed/Free Size Preset Setting is saved by pressing the JOG button.
* The displaySize
blinks
while Setting
being accepted.
Do notallturn
off power
during this
stage.
3.3.
Fixed/Free
Preset
is is
registered
atat
once
byby
pressing
the
JOG
key.
Fixed/Free Size
Preset
Setting
registered
all
once
pressing
the
JOG
key.
* The
display
blinks
while
registration
is
in
process.
Do
not
turn
off
the
power.
* The display blinks while registration is in process. Do not turn off the power.
Blinking
Blinking
ation/Cancel
Fixed■
Preset
Registration/Cancel
■ Fixed Preset Registration/Cancel
TO
CANCEL
FIXED
PRESET
z
Fixed
Preset
Cancel
Fixed
Preset
Registration/Cancel
z
Fixed
Preset
Cancel
Example:
0 x 11” 8.5”
x 11”
Vertical
2-cut
Example:
No.0
8.5”
2-cut
ixed Preset
Registration
z
Fixed
Preset Registration
Example:
No.0No.
8.5”
x 11” Vertical
Vertical
2-cut
z
Fixed
Preset
Registration
1.1.
Select
preset
No.0
byby
pressing
the
speed
upup
key
and
the
slow
down
key.
Select
preset
No.0
pressing
the
speed
key
and
the
slow
down
key.
2.
Press
the
–
key
to
cancel
preset.
1. 2.8.5”
Select
preset
No.
0 to
bycancel
pressing
the speed No.0
up or speed
down
button.
mple:
al 2-cut
No.0
x
11”
Vertical
2-cut
Example:
8.5”
x
11”
Vertical
2-cut
Press
the
–
key
preset.
Example:
No.0
8.5” x 11” Vertical 2-cut
Lights
up
Blinking
2.
Press
the
“-”pressing
button
to the
cancel
the
1.
ngSelect
the speed
preset
up
No.0
key
and
by
slow
speed
key.preset.
up
1. key
Select
andpreset
thekey
slow
No.0
down
by
key. down
thekey.
speed up key and the slow down key.
Lights
up
Blinking
1. Select presetthe
No.0
bydown
pressing
the
speed
up
and
thepressing
slow
To
cancel
more
presets,
repeat
steps
1
and
2.
gistration.
* The display
blinks
before
registration.
* The display blinks before registration.
* The
display
blinks
before registration.
2.eset.
Press the
+
key
to
register
preset.
2.
2. Press the + key to register preset. Press the + key to register preset.
Blinking Lights
up
Lights
Blinking
up Lights up
Lights up
Blinking
* When
you
desire
toto
continue
cancel,
repeat
the
above
procedures
1 and
2.2.
* When
you
desire
continue
cancel,
repeat
the
above
procedures
1 and
3.3.
Cancel
ofof
Fixed/Free
Size
Preset
Setting
is is
registered
allall
atat
once
byby
pressing
the
JOG
key.
Cancel
Fixed/Free
Size
Preset
Setting
registered
once
pressing
the
JOG
key.
* The
display
blinks
while
registration
is
in
process.
Do
not
turn
off
the
power.
registration,
When you* When
desire
repeat
to
the
continue
above
procedures
registration,
1
repeat
and
*
When
2.
the
you
above
desire
procedures
to
continue
1
and
registration,
2.
repeat
the
above
procedures 1 and 2.
* The
display
while registration
in process.
Do procedures
not turn off the
power.
you
desireblinks
to continue
registration,isrepeat
the above
1 and
2.
Blinking
BlinkingSize Preset Setting is cancelled all at once by pressing the JOG button.
3. Fixed/Free
3.
ngFixed/Free
is registered
Size
all Preset
at
once
Setting
by Preset
pressing
is registered
the JOG
Fixed/Free
key.
at once
by
Size
pressing
the
Setting
JOG this
key.
isthe
registered
all at once by pressing the JOG ke
* The
display
blinks
while
being
accepted.
Do not
offPreset
power
during
stage.
3. Fixed/Free
Size
Setting
is3.all
registered
allturn
at
once
by
pressing
JOG key.
gistration
* The display
is in*process.
blinks
while
Doblinks
registration
not turn
offregistration
the
is inpower.
process.
* The
Do
notblinks
turnDo
off
while
the turn
registration
power.
is in process. Do not turn off the power.
The
display
while
is indisplay
process.
not
off the power.
Blinking Blinking
Blinking
[ NOTE
] ]
[ NOTE
DoDo
not
turn
offoff
the
power
while
registration
is is
in in
process.
turned
offoff
byby
mistake,
please
not turn
the
power
while
registration
process. If itIf is
it is
turned
mistake,
please
register
the
setting
again.
register
the
setting
again.
ixed Preset
Cancel
z
Fixed
Preset Cancel
12
z
Fixed Preset Cancel
■ Fixed Preset Registration/Cancel
z
Fixed
Preset FREE
Registration
TO
INPUT
SIZE
PRESET
■ Free Size Preset Registration/Cancel
Example:
8.5”13x 11” 5.5”
Vertical 2-cut
Example:No.0 No.
z
Free
Size
Preset
Registration
1.Free
SelectSize
presetPreset
No.0 by pressing
the speed up key and the slow down key.
Registration/Cancel
The display
blinks
before
registration.
1. *Select
preset No.
13 by
pressing
the speed up or speed down button.
Example:
No.13
5.5”
thecut
+ key
2.2. Press
Input the
size to
byregister
pressingpreset.
the “+” and the “-” buttons.
z
Free
Size Preset
Registration
1.Blinking
Select
preset No.13
by pressing the speed up key and the slow down key.
To add more presets, repeat steps 1 and 2. Lights up
2. Input cut size by pressing the + key and the – key.
Example:
No.13
Lights
up 5.5”
1. Select preset No.13 by pressing the speed up key and the slow down key.
2. Input cut size by pressing the + key and the – key.
Lights up
* When you desire to continue registration, repeat the above procedures 1 and 2.
* When you desire to continue registration, repeat the above procedures 1 and 2.
3. Fixed/Free Size Preset Setting is saved by pressing the JOG button.
Fixed/Free
Size
Preset
Setting
registered
once
pressing
JOG
key.
3. 3.
Fixed/Free
Size
Preset
Setting
is is
registered
allall
at at
once
byby
pressing
thethe
JOG
key.
* The display blinks while being accepted. Do not turn off power during this stage.
* The
display
blinks
while
registration
process. DoDo
turn
power.
* The
display
blinks
while
registration
is is
in in
process.
notnot
turn
offoff
thethe
power.
* When
you
desire
to
continue
registration,
repeat
the
above
procedures
1
and
2.
Blinking
Blinking
3. Fixed/Free Size Preset Setting is registered all at once by pressing the JOG key.
* The display blinks while registration is in process. Do not turn off the power.
Blinking
■
■TO
Fixed
PresetFREE
Registration/Cancel
CANCEL
SIZE PRESET
z
FreePreset
Size Preset
Cancel
z
Fixed
Cancel
z
Fixed Preset
Registration
Example:
No.
13
Example:
No.13
Example:
No.0
8.5” x 11” Vertical 2-cut
z
FreeSelect
Size Preset
Cancel
preset
No.13
by pressing
the
speed
up key
slow
down
1. 1.
Select
preset
No.0
by pressing
the
speed
up key
andand
the the
slow
down
key.key.
Example:
No.0
8.5”
x
11”
Vertical the
2-cut
1. 2.
Select
preset
No.
13
by pressing
speed up or speed down button.
Set
cut
size
to
“0”.
2. Press the
– key to cancel
preset.
preset
Example:
No.13
2.1. Select
Set
cut
size to No.0
“0”. by pressing the speed up key and the slow down key.
Blinking
Lights
up blinks before registration.
Blinking
The
display
1.*To
Select
preset
pressing
speed
cancel
more No.13
presets,by
repeat
stepsthe
1 and
2. up key and the slow down key.
2.2.Press
the
+
key
to
register
preset.
Set cut size to “0”.
Blinking
Lights up
Blinking
* When
you
desire
cancel cancel,
registration,
repeat
the above
procedures
and 2.
* When
you
desire
to to
continue
repeat
the above
procedures
1 and1 2.
3. Cancel of Fixed/Free Size Preset Setting is registered all at once by pressing the JOG key.
* Theof
display
blinksSize
whilePreset
registration
is is
inregistered
process. all
Do not
turnbyoffpressing
the power.
Cancel
Fixed/Free
Setting
once
*3.*When
you
desire
totocontinue
registration,
repeat
theabove
aboveat
procedures
1and
and2.2.the JOG key.
When
you
desire
cancel
registration,
repeat
the
procedures
1
Blinking
The display blinks
while
registration
is in
Do not turn
off the
power.
3. 3.*Fixed/Free
Preset
Setting
is cancelled
allprocess.
at registered
once by pressing
the JOG
button.
Cancel of Size
Fixed/Free
Size Preset
Setting
is
all at once
by pressing
the JOG key.
Blinking
3. Fixed/Free
Size
Preset
Setting
is registered
allturn
at once
by not
pressing
the
JOG
key.
**The
blinks
while
being
accepted.
Doinnot
off power
during
stage.
Thedisplay
display
blinks
while
registration
is
process.
Do
turnthis
off
the
power.
*Blinking
The display blinks while registration is in process. Do not turn off the power.
Blinking
[ REFERENCE ]
When ]cut size is 2.5 - 9.9 inches: preset is available.
[ NOTE
cutoff
size
0: preset
is cancelled.
DoWhen
not turn
theispower
while
registration is in process. If it is turned off by mistake, please
[ To
REFERENCE
] process (just feeding): register “PASS” in Fixed Preset.
register
non-cut
register the setting again.
When
cut] size is 2.5 - 9.9 inches: preset is available.
[ NOTE
NOTES:
When
is 2.5while
9.9 registration
inches: preset
When
size
isthe
0:size
preset
is- cancelled.
Do notcut
turn
offcut
power
is is
inavailable.
process. If it is turned off by mistake, please
z
Fixed
Preset
Cancel
When
cut size
is 0: preset
is cancelled.
To
register
process
(just feeding):
register “PASS” in Fixed Preset.
register
thenon-cut
setting
again.
[ NOTE ]To choose non-cut process (just feeding): choose “PASS” in fixed preset.
Example:
8.5”
11” Vertical
2-cut
Do notNo.0
turn off
thexpower
while registration
is27in process. If it is turned off by mistake, please
1.register
Select the
preset
No.0
by
pressing
the
speed
up key and
13 the slow down key.
setting again.
2. Press the – key to cancel preset.
Lights up
Blinking
■ Option
■ Option CONVEYOR
Independent OPERATION
Operation
OPTIONAL
Optional conveyer unit can be installed in the paper ejection part on the V-417.
Please
contact
service
person
concerning
The optional
Output
Conveyor
can
bean
installed
in
the
paper
outfeed
ofthe
theoptional
FD 4170.conveyer
This is operation
mode
thatour
optional
conveyer
unit independently
operates unit.
when
conveyer unit is installed on the machine.
the optional
The conveyor can be operated independently by following these steps:
Conveyer
Unit the machine “stand-by” status.
1. Turn thez
power
on to make
Turn on power to place burster in Stand-by mode.
2. The machine starts operating by holding down the STOP/C key and the JOG key
2.
Start operation
byconveyer
holding down
STOP/C
The
unitthe
can
handlebutton
large amount of
simultaneously.
and JOG button
simultaneously.
processing.
Already burst paper can be taken out freely with
LCD operation
this unit even while the machine is in process of
bursting.
1.
3.
Independent operation mode finishes by releasing the
JOG button.
■
3. Independent
operationIndependent
mode completes by
releasing the JOG key.
Option
Operation
This is operation mode that an optional conveyer unit independently operates when the optional
TROUBLE-SHOOTING
conveyer unit is installed on the machine.
TROUBLE
REMEDY
1. Turn the power on to make the machine “stand-by” status.
Power will not turn on, even after pressing “I” side of Check that power cable is properly connected to the
2. The machine starts operating by holding
down the STOP/C key and the JOG key
power switch
machine and an appropriate wall outlet
simultaneously.
Machine does not operate or stops even after
pressing the START
button
LCD
operation
Check the LCD display for an error message. Refer
to Error Displays (on following pages), then complete
the action required.
3. Independent operation mode completes by releasing the JOG key.
29
14
29
■ ErrorDISPLAY
Display GUIDE
ERROR
* 2 error displays appear in turn.
Display
Status and Solutions
Status:
Paper jam in the paper feed part
[ FEEd ]→[ Err. ]
Solutions: Check the paper feed tray and remove jammed paper.
After removing the jammed paper, press the STOP/C key
to clear the error display.
Details:
Refer to the How to deal with “[ FEEd. ]→[ Err. ]” on
16
page 32.
Status:
Safety cover is open.
[ OPEn ]
Solutions: Close the safety cover.
16
Details:
Refer to the How to deal with “[ OPEn ]” on page 33.
Status:
No paper is set.
[ SEt ]→[ PAPE. ]
Solutions: There is no paper in the paper feed tray. Place the paper
in the paper feed tray or press the STOP/C key.
Details:
[ PAPE. ]→[ LEFt ]
Status:
Solutions:
Details:
[ Cut ]→[ Err. ]
Status:
Solutions:
Details:
[ PASS ]→[ Err. ]
Status:
Solutions:
Details:
[ Err.1 ]
[ Err.5 ]
Others
Status:
Solutions:
Details:
Status:
Solutions:
Solutions:
Refer to the How to deal with “[ SEt ]→[ PAPE. ]” on
17
page 33.
Paper remains inside the machine (cut part).
Remove the paper and press the STOP/C key to clear the
error display.
Refer to the How to deal with “[ PAPE. ]→[ LEFt ]” on
18
page 34.
Cut error
Remove the paper in the cut part or paper ejection part
and, press the STOP/C key to clear the error display.
Refer to the How to deal with “[ Cut ]→[ Err. ]” on page
18
34.
Paper jam in the paper ejection part
Remove the paper in the cut part or paper ejection part
and, press the STOP/C key to clear error display.
Refer to the How to deal with “[ PASS ]→[ Err. ]” on
18
page 34.
Main motor lock (Paper remains in the cut part or paper
ejection part.)
Remove the paper and press the STOP/C key.
19
Refer to the How to deal with “[ Err.1 ]” on page 35.
Overload
Turn off the power to the machine and leave it for over 3
hours.
Turn off the power to the machine and then turn it on after
a few seconds. If the same error message is displayed,
note the error content and contact our service person.
31
15
How to deal with “[ FEEd. ]→[ Err. ]”
■ ClearingERROR
Error and
How to Deal with Trouble
CLEARING
MESSAGES
● Paper feed part
1. Remove
the jammed
● Paper
feed partpaper at the entrance of
How to deal with “[ FEEd. ]→[ Err. ]”
1.
Remove
thepart
jammed paper at the entrance of
the machine.
● Paper feed
machine.
1. the
Remove
the jammed paper at the entrance of
the machine.
WARNING
WARNING
Be sure to remove
the power plug
Be sure to WARNING
remove the power plug
from the
outlet
when
working
nearnear
from
the
outlet
when
working
● PaperBe
feed
part
sure
to
remove
the
power
movable
parts due
to
paper
jam jam
andplug
movable
parts
due
to
paper
and of
fromthe
the
outlet paper
when at
working
near
1. Remove
jammed
the entrance
so on. movable
so
on.
the machine. parts due to paper jam and
so on.
Press
the STOP/C
to clear
the error
display.
2. Press2.the
STOP/C
key tokey
clear
the error
display.
WARNING
2. Press
the STOP/C key to clear the error display.
Be sure to remove the power plug
from the outlet when working near
movable parts due to paper jam and
so on.
2. Press the STOP/C key to clear the error display.
● When misfeed has occurred:
●
When misfeed
has occurred:
● When misfeed
has occurred:
1. Adjust the paper feed pressure adjusting lever.
Adjust
the paper
feed pressure
adjusting
lever.
1. Adjust1.the
paper
feed pressure
adjusting
lever.
* When double feed has occurred
Move
the lever
“LIGHT”.
*→
When
double
feedtohas
occurred
* When*double
feed
has
occurred
When
paper
cannot
be
fed
→ Move the lever to “LIGHT”.
→ Move
the
lever
to
“LIGHT”.
→
Move
the
lever
to
“HEAVY”.
* When paper cannot be fed
* When paper
cannot
be to
fed“HEAVY”.
→ Move
the lever
→ Move the lever to “HEAVY”.
● When misfeed has occurred:
1. Adjust the paper feed pressure adjusting lever.
How
to deal
with
[feed
OPEn
How
to deal
with
[ ]OPEn
]
* When
double
has
occurred
→ Move the lever to “LIGHT”.
* When paper cannot be fed
→ Move the lever to “HEAVY”.
32
1. Close the safety cover.
1. Close the safety cover.
32
* The error display disappears by closing the
* The error safety
display
disappears by closing the 32
cover.
safety cover.
How to deal with [ SEt ]→[ PAPE. ]
How to deal with [ SEt ]→[ PAPE. ]
16
32
deal[ with
[ SEtPAPE.
]→[ PAPE.
How toHow
dealtowith
SEt ]→[
] ]
1. Move the paper feed tray up/down lever
1. Move the
paper feed
tray up/down
lever
downwards
to place
the paper on
the paper
feed tray.
downwards
to place the paper on the paper
feed tray.
2. Move the paper feed tray up/down lever upwards.
2. Move the
paper
traydisappears
up/down by
lever
upwards.
* The
errorfeed
display
setting
the
paper or pressing the STOP/C key.
* The error display disappears by setting the
paper or pressing the STOP/C key.
33
33
17
How to deal with [ PAPE. ]→[ LEFt ]
How to deal with [ Cut ]→[ Err. ]
How to deal with[ PASS ]→[ Err. ]
1. Press the “O” side of the power switch to turn
off the power and remove the power plug from
the outlet.
WARNING
Be sure to remove the power plug
from the outlet when working near
movable parts due to paper jam and
so on.
2. Open the safety cover and remove the jammed
paper with tweezers.
* If the paper cannot be removed with tweezers,
do not try to remove it forcefully.
Follow the “● Removing paper using the JOG
key“ on page 36.
20
3. Close the safety cover. Connect the power
plug to the outlet and press the “I” side of the
power switch to turn on the power.
* If “[ PAPE. ]→[ LEFT ]” still appears even after
removing the paper, follow the “● Cleaning
sensor part“ on page 37.
21
18
How to deal with [ Err.1 ]
How to deal with [ Err.1 ]
How to deal with [ Err.1 ]
* If an excessive load is applied to the machine
during operation
due to paper
andtoso
* If an excessive
load is jam
applied
theon,
machine
during
operation
due
to
paper
jam
and
so on,
the breaker
works
for
safety
and
the
machine
* If an excessive load is applied to the machine
Ifstops.
an excessive
load
is
applied
to
the
burster
during
the
breaker
works
for
safety
and
the
machine
during operation
due to to
paper
and so on, operation due to paper jam, etc, the circuit breaker will
*shut
If andown
excessive
load is applied
the jam
machine
the
machine.
If
that
happens,
follow
the instructions below.
stops.
the breaker works
for safety andbelow.
the machine
If
this happens,
procedures
during
operationfollow
due tothe
paper
jam and so on,
If
this happens, follow the procedures below.
stops.
the breaker
works for safety
and
the machine
If this
follow
the procedures
below.
1.stops.
Press the
“O”happens,
side of the
power
switch to turn
off
1. Press the “O” side of the power switch to turn off
Ifthe
thispower.
happens,
follow
procedures
power.
1.the
Press
the “O”the
side
of the powerbelow.
switch to turn off
the power.
1. Press the “O”
side of the power switch to turn off
WARNING
WARNING
the power.
to WARNING
remove
the power
Be sure Be
to sure
remove
the power
plug plug
from
the
outlet
when
working
from theBeoutlet
working
near near
sure when
to remove
the power
plug
movable
parts
due
to
paper
jam near
and
the
whenjam
working
WARNING
movable from
parts
dueoutlet
to paper
and
so
on.
so on. movable parts due to paper jam and
Be sure so
toon.
remove the power plug
from the2.outlet
working
near
Removewhen
the paper
remaining
inside the machine
insideand
the machine
2.
Removeparts
the
paper
remaining
movable
due
to
paper
jam
if
there
is
any.
2. Remove the paper remaining inside the machine
there is ifany.
soifon.
there is any.
2. Remove the paper remaining inside the machine
if there is any.
3. Confirm that there is no paper inside the machine
press
down
theisbreaker
button
out.
3. and
Confirm
that
there
no paper
insidesticking
the machine
3. Confirm that there is no paper inside the machine
and press down the breaker button sticking out.
and press down the breaker button sticking out.
3. Confirm that there is no paper inside the machine
and press down the breaker button sticking out.
4. Press the “I” side of the power switch to turn on
power.
the
machine
can restart.
4. the
Press
the “I” Now,
side of
the
power switch
to turn on
the power. Now, the machine can restart.
4. Press the “I” side of the power switch to turn on
the power. Now, the machine can restart.
* If “I”
theside
machine
does
not restart
the above
4. Press the
of the
power
switchafter
to turn
on
were taken,
contact
ourafter
service
* actions
If theNow,
machine
not restart
theperson.
above
the power.
the does
machine
can restart.
actions were taken, contact our service person.
If *the
burster
still does
contact
your
Service
If the machine
doesnot
notstart,
restart
after the
above
Technician.
actions were taken, contact our service person.
35
35
* If the machine does not restart after the above
actions were taken, contact our service person.
35
19
● Removing paper using the JOG key
● Removing paper using the JOG key
1. Close the safety cover.
1. Close the safety cover.
2. Remove the paper from the paper feed tray.
2. Remove the paper from the paper feed tray.
3. Pull out the paper with a hand while feeding
3. Pull out the paper with a hand while feeding
it by holding down the JOG key.
it by holding down the JOG key.
[ IMPORTANT ]
[ IMPORTANT
Note for] operating the JOG key
sure
close
the
safety
cover.to close the
Note
for
operating
the
JOG
keysure
NOTE: To Be
use
the to
JOG
button,
be
Press
thethe
JOG
key while
observing
the statusthe
of
safety
cover.
Press
the
JOG
button
while watching
Be sure
to
close
safety
cover.
paper
jam
because
paper
jam
sometimes
gets
jammed
paper
as
the
jam
may
get
worse.
Press the JOG key while observing the status of
worse.
paper jam
because paper jam sometimes gets
worse.
WARNING
The WARNING
driving part contains driving
parts. Care should be taken when
workingpart
in it. contains driving
The driving
parts. Care should be taken when
working in it.
4. Set the paper again.
5. Clear the error display by pressing the STOP/C
4. Set the paper
again.
key.
5. Clear the error display by pressing the STOP/C
key.
36
20
● Cleaning sensor part
1. Press the “O” side of the power switch to turn off
the power and remove the power plug from the
outlet.
WARNING
Be sure to remove the power plug
from the outlet when working near
movable parts due to paper jam and
so on.
2. Open
the safety
cover.
the sensor
part
Open
the safety
cover.
Spray Spray
the sensor
with canned
air, or
gently
cleanwhich
with aiscotton
swab
with
air spray
available
in to
theremove
marketpaper
or
dustgently
residue.
clean it with a cotton swab to remove paper
powder.
3. Close the safety cover. Insert the power plug
into the outlet and then press the “I” side of the
power switch to turn on the power.
If the
burster
still does
contact
yourabove
Service
* If the
machine
doesnot
notstart,
restart
after the
Technician.
actions were taken, contact our service person.
21
Sensor part