Blue Ox BX2411 baseplate Installation Instructions

BX2411
2011-15 Dodge Durango
2014-15 Jeep Grand Cherokee Summit
Installation Instructions
Please read BOTH these Installation Instructions and the General Instructions prior to
installing or operating this equipment.
1. Blue Ox® towing products and accessories are
intended to be installed by Blue Ox® Dealers
who are familiar with our products and have the
equipment and knowledge necessary to do “fit
work”. If needed, Blue Ox® Dealers can be found
at www.blueox.com or by contacting our Customer
Care Department at (402) 385-3051.
Serial Number
Attachment Tab Height: 18”
Attachment Tab Width: 27-1/2”
2. Many Blue Ox® baseplates are designed to use
existing holes and hardware to mount the baseplate
to the towed vehicle. Even though bolts are there,
do not assume they are adequate for baseplate
mounting. Always use the hardware supplied in the
hardware kit and existing hardware as specified in
the installation instructions.
Bolt Torque Specifications
Torque in Foot-Pounds for Inch Bolts
Bolt Size
Grade 5
Grade 8
1/4”
10
14
5/16”
19
29
3/8”
33
47
7/16”
54
78
1/2”
78
119
5/8”
154
230
3/4”
257
380
Bolt Torque Specifications
Torque in Foot-Pounds for Metric Bolts
2014 Dodge Durango shown
!
2014 Jeep Grand Cherokee Summit
If the front of your vehicle looks different than
this, please contact us at (402)385-3051.
Bolt Size
Grade 8.8
Grade 10.9
6MM
6
8
8MM
16
22
10MM
31
40
12MM
54
70
14MM
89
117
16MM
161
230
18MM
222
318
WARNING
Failure to read and follow these instructions
could result in separation of the towed vehicle
from the tow bar, causing property damage,
loss of towed vehicle, personal injury or death.
Reference your vehicle owner’s manual for manufacturer’s towing specifications.
405-0371 Rev A
Page 1 of 8
12/1/14
BX2411
2011-15 Dodge Durango
2014-15 Jeep Grand Cherokee Summit
Installation Instructions
Instruction Notes: The fascia is removed and reinstalled for the baseplate installation. Some drilling
and trimming is required.
Place all components that are removed on a flat, sturdy surface. All items will be reinstalled unless
otherwise noted after the baseplate is installed.
The dimensional variations between otherwise identical vehicles can be considerable. While the
baseplate was designed for easy installation, it may be necessary to tailor the baseplate slightly to
compensate for vehicle manufacturer’s tolerances.
The BX8848 4-Diode Wiring Kit is recommended for the 2014 Dodge Durango.
The BX8869 Tail Light Wiring Kit is recommended for all other models.
Drill a hole according to the tail
light wiring kit instructions.
NOTICE
• Handling of some cosmetic parts when installing this product may require the use of protective covers, rags, specialty tools, etc. to prevent damage.
• When using power drills be aware of the dangers of torque and drill bit length.
• When using a reciprocating saw be aware of objects behind the cutting surface.
• Use a good quality paint to spray cut edges of frame to prevent rusting.
• Be sure that ALL electrical connections are plugged in and accessories are functioning properly
before reinstalling the fascia.
• The baseplate is computer tested to your vehicle’s GVWR, exceeding this weight will void the
manufacturer’s warranty.
• Be sure to use Loctite® Red on all bolts before tightening. Tighten all bolts according to the torque chart provided.
• Dealer or installer be certain the user receives these instruction sheet.
• If the baseplate is in an accident, it must be replaced. DO NOT use it again! An accident can
cause unseen damage and using it again could result in more damage or serious injury. DO NOT
use the baseplate if it is damaged or missing parts.
405-0371 Rev A
Page 2 of 8
12/1/14
BX2411
2011-15 Dodge Durango
2014-15 Jeep Grand Cherokee Summit
Installation Instructions
Tools Required
Large Vise Grip
Flat Screwdriver
Phillips
Screwdriver
Utility Knife
Torque Wrench
Rivet Gun
Tape Measure
Loctite® RED
8MM Socket
10MM Socket
16MM Socket
30MM Socket
30MM Wrench
9/16” Socket
9/16” Wrench
MODELS WITHOUT
TOW HOOKS
9
1
5
17
6
8
14
4 PIN CONNECTOR
MODELS WITH
TOW HOOKS
18
BREAKAWAY SWITCH
7
3
12
18
21
2
4
16
15
6 PIN CONNECTOR
22
19
12
13
11
22
12
20
22
10
19
10
Item No. Part No.
Description
Qty.
1.................................... 61-7272................................. BX2411 DS Baseplate...............................................................1
2.................................... 61-7273................................. BX2411 PS Baseplate...............................................................1
3.................................... 62-3468................................. Attachment Tab Assembly with Hole..........................................2
4.................................... 101-6845............................... Electrical Bracket.......................................................................1
5.................................... 102-7056............................... Breakaway Bracket....................................................................1
6.................................... 102-7106............................... Locking Plate.............................................................................2
7.................................... 107-3184............................... Spacer Tube 3/4”Ø x 1-23/32”...................................................4
8.................................... 107-3496............................... Spacer Tube 3/4”Ø x 3”.............................................................4
9.................................... 201-0050............................... 1/4”-20 x 3/4” Hex Head Bolt, Grade 5, ZP................................1
10.................................. 201-0077............................... 3/8”-16 x 4-1/2” Hex Head Bolt, Grade 5, ZP............................4
11................................... 201-0204............................... 1/4”-20 x 1-1/4” Hex Head Bolt, Grade 5, ZP............................2
12.................................. 201-0429............................... 10MM-1.5 x 80MM Hex Head Bolt, Grade 8.8, ZP....................4
13.................................. 201-0432............................... 10MM-1.5 x 100MM Hex Head Bolt, Grade 10.9, ZP................4
14.................................. 201-0654............................... #10-16 x 1” Self Drilling Screw..................................................1
15.................................. 201-0192............................... #10-32 x 1-1/2” Phillips Pan Head Screw..................................2
16.................................. 202-0047............................... #10-32 Hex Nut.........................................................................2
17.................................. 202-0090............................... 3/8”-16 Hex Nylon Insert Lock Nut, ZP......................................4
18.................................. 202-0102............................... 1/4”-20 Hex Nylon Lock Nut, ZP................................................3
19.................................. 203-0003............................... 3/8” Flat Washer, ZP..................................................................8
20.................................. 203-0010............................... 3/8” Lock Washer, ZP................................................................4
21.................................. 203-0054............................... #10 Lock Washer, ZP................................................................2
22.................................. 203-0104............................... 10MM Lock Washer, ZP............................................................8
23.................................. 226-0049(not shown)............. Class IV Safety Cables..............................................................2
24.................................. 229-0512(not shown)............. 1/2” Quicklink, ZP......................................................................2
25.................................. 229-0536(not shown)............. 6.3MM Plastic Rivet...................................................................4
26.................................. 290-0437(not shown)............. Black Cap Plug Receiver...........................................................2
Important:
Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt is lost or in need of
replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of the same grade (In most cases it will be Grade
5, please reference the parts list above). Replacement parts may be ordered through your nearest Blue Ox® Dealer or Distributor. Failing to follow and/
or altering these installation instructions in either installation or required equipment will void the manufacturer’s warranty. Towing behind a non-motorized
vehicle will void the warranty.
405-0371 Rev A
Page 3 of 8
12/1/14
BX2411
2011-15 Dodge Durango
2014-15 Jeep Grand Cherokee Summit
Installation Instructions
Fascia Removal: 2014 Dodge Durango






2. In the wheel well, using a 10MM socket,
remove the top screw (gray). Using a
8MM socket, remove the lower screw
(black). Then remove the two (2) plastic
rivets (white). Do this on both sides of the
vehicle.



1. Remove the two (2) Phillips head push
pins from the top edge of the fascia.
3. On the underside of the fascia, turn the
three (3) locking knobs 90° to release.
5. Pull the top corners of the fascia out
releasing the clips behind, continue
working inward towards the grille releasing
the clips under the headlights. Pull the
fascia forwards disconnecting all electrical
connections and set the fascia aside.
Continue to Step #1 on page #6
405-0371 Rev A
Page 4 of 8
12/1/14
BX2411
2011-15 Dodge Durango
2014-15 Jeep Grand Cherokee Summit
Installation Instructions
Fascia Removal: 2014 Jeep Grand Cherokee





2. Using a utility knife, remove the two (2)
plastic rivets from outer edge of the wheel
well (white). Then using a 10MM socket,
remove the upper screw (gray). Do this on
both sides of the vehicle.




1. On the topside of the fascia, remove the
two (2) push pins.
3. Underneath the bumper, remove the two
(2) push pins. Do this on both sides of the
vehicle.
4. On the underside of the fascia, release the
fascia clips by turning 90°. There is one
(1) towards the middle (white) and one (1)
towards the outer edge by the tire (gray).
Do this on both sides of the vehicle.
5. Pull the top corners of the fascia out
releasing the clips behind, continue working
inward towards the grille releasing the clips
under the headlights. Pull the fascia forwards
disconnecting all electrical connections and
set the fascia aside.
Continue to Step #1 on page #6
405-0371 Rev A
Page 5 of 8
12/1/14
BX2411
2011-15 Dodge Durango
2014-15 Jeep Grand Cherokee Summit
Installation Instructions

Baseplate Installation: All Models






1. Prior to installing the baseplate to the
vehicle, install the appropriate spacer
tubes into the slots of the baseplate. The
tubes will vary depending on whether the
vehicle is equipped with tow hooks or not.
Reference page 3.
2. Models equipped with tow hooks: Using
a 16MM socket, remove the two (2) bolts
from the front side. Then using a 30MM
socket or wrench, remove the nut from
the backside of the tow hook. Remove the
tow hook from the vehicle. Do this on both
sides of the vehicle.

405-0371 Rev A





3. Models equipped with tow hooks: Using
a 16MM socket, remove the two (2) bolts
from the tow hook bracket. Remove the
tow hook bracket from the vehicle. Do this
on both sides of the vehicle.
4. Models equipped with tow hooks: Slide
the baseplate into position on the frame.
Install two (2) 10MM-1.5 x 80MM bolts
with 10MM lock washers into the bottom
holes (white). Install 10MM-1.5 x 100MM
bolts with 10MM lock and 3/8” flat washers
thru the baseplate into the bumper on
both the front holes (gray). Tighten all
hardware. Do this on both sides of the
vehicle.
Page 6 of 8
12/1/14
BX2411
2011-15 Dodge Durango
2014-15 Jeep Grand Cherokee Summit
Installation Instructions





5. Models equipped without tow hooks:
Slide the baseplate into position on the
frame. Install two (2) 10MM-1.5 x 80MM
bolts with 10MM lock washers into the
bottom holes (white). Insert 3/8”-16 x 4-1/2”
bolts with 3/8” lock and flat washers into the
front holes with the locking plate and 3/8”-16
lock nuts on top of bumper (inset). Tighten
all hardware. Do this on both sides of the
vehicle.
6. Attach the permanent baseplate safety cables to the provided convenience link on
the baseplate. The photo above shows the
recommended installation of the cables to
frame of vehicle. Additional options may
interfere with suggested mounting; in this
case, secure the cables to a solid piece of
the frame as described in the instructions
included with the permanent baseplate safety
cables. Be sure the safety cables do not rub
against any hoses or moving parts. Do this
on BOTH sides of the vehicle.


Dodge Durango
7. Dodge Durango Only: Trim the plastic
support on the backside of the fascia as
shown for baseplate clearance.
405-0371 Rev A
8. Optional: If installing a breakaway,
measure over approximately 7” from the
convenience link, install the breakaway
bracket to the bumper with a #10-16 x 1”
self drilling screw. Attach the breakaway to
the bracket with a 1/4”-20 x 3/4” bolt and
1/4”-20 lock nut.
Page 7 of 8
12/1/14
BX2411
2011-15 Dodge Durango
2014-15 Jeep Grand Cherokee Summit
Installation Instructions

9. Hold the fascia as close to its original
position, mark and trim the fascia around
the convenience links and attachment
tabs. Reinstall the fascia. Using the rivet
gun, replace the rivets in each wheel well.
CUSTOMER SERVICE COMMITMENT
Blue Ox® is committed to providing you with exceptional customer care throughout your lifetime
with our products. Our team is here to assist you with any questions you may have regarding the
performance of your product. Simply call (402) 385-3051 and you can speak with our customer care
team.
Additionally, please visit our website to see which rallies our Destination America team will be
attending. For a nominal fee, our service technician will service your towing system to ensure it’s in
proper working condition. Also, as a commitment to our customers, should you visit our factory, you
can stay at our full service Blue Ox® campground at no charge along with enjoying a factory tour.
Again, thank you for being our customer and for the confidence you have shown in the performance
of our products. It is because of customers like you we enjoy the success we have today.
© 2014 Blue Ox
One Mill Road, Industrial Park
Pender, Nebraska 68047
Phone: (402) 385-3051
Fax: (402) 385-3360
www.blueox.com
405-0371 Rev A
Page 8 of 8
12/1/14