E53x

E53x
Installation Guide
Power Monitoring
TM
Installation Guide
Power Monitoring
E53B3C
TM
Specifications (cont.)
E53B3C
OPERATING CONDITIONS
Operating Temperature Range
Storage Temperature Range
E53B3C
COMPLIANCE INFORMATION
IP40 front panel, IP20 casing, pollution degree 2, IK08 impact rating
MID
2004/22/EC compliance
Not suitable for wet locations. For indoor use only.
Dimensions
Specifications
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
•
•
•
•
•
Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
This equipment must only be installed and serviced by qualified electrical personnel.
Read, understand and follow the instructions before installing this product.
Turn off all power supplying equipment before working on or inside the equipment.
Product may use multiple voltage/power sources. Be sure all sources of power
have been disconnected before servicing.
• Use a properly rated voltage sensing device to confirm power is off.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
• Only install this product on insulated conductors.
Failure to follow these instructions will result in death or serious injury.
A qualified person is one who has skills and knowledge related to the construction and
operation of this electrical equipment and the installation, and has received safety
training to recognize and avoid the hazards involved.
NEC2011 Article 100
No responsibility is assumed by Veris Industries for any consequences arising out of the
use of this material.
NOTICE
This product is not intended for life or safety applications.
Do not install this product in hazardous or classified locations.
The installer is responsible for conformance to all applicable codes.
Mount this product inside a suitable fire and electrical enclosure.
FCC PART 15 INFORMATION
NOTE: This equipment has been tested by the manufacturer and found to
comply with the limits for a class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
residential environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Modifications to this product without the express authorization of the
manufacturer nullify this statement.
For use in a Pollution Degree 2 or better environment only. A Pollution Degree 2 environment
must control conductive pollution and the possibility of condensation or high humidity.
Consider the enclosure, the correct use of ventilation, thermal properties of the equipment,
and the relationship with the environment. Installation category: CAT II or CAT III. Provide
a disconnect device to disconnect the meter from the supply source. Place this device in
close proximity to the equipment and within easy reach of the operator, and mark it as the
disconnecting device. The disconnecting device shall meet the relevant requirements of
IEC 60947-1 and IEC 60947-3 and shall be suitable for the application. In the US and Canada,
disconnecting fuse holders can be used. Provide overcurrent protection and disconecting
device for supply conductors with approved current limiting devices suitable for protecting the
wiring. If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the device may be impaired.
3.4”
(87 mm)
VOLTAGE INPUTS
Measured Voltage
Frequency
Voltage Impedance
Wire Size
Terminal Block Torque
1.8”
(45 mm)
100-277VLN; 173-480VLL ± 20%
OK
50/60 Hz ± 10%
Nominal Current
Measured Current
Config
4.4 in-lb (0.5 N-m) max.
3.5”
(90 mm)
1A or 5A
Frequency
50/60 Hz ± 10%
Impedance
<0.3 mΩ
Wire Size
Terminal Block Torque
2.7”
(69 mm)
20mA - 6A
10A continuous; [email protected]/hr
Minimum Wire Temperature
Rating
3.7”
(95 mm)
24 to 14 AWG (0.2 to 2.5 mm2)
Withstand
Burden
ESC
Reset
3 MΩ
CURRENT INPUTS
2.5”
(64 mm)
J
Product Diagram
<0.024 [email protected]
90°C (194°F)
A
B
18 to 10 AWG (0.8 to 6 mm2)
C/- T1
7.0 in-lb (0.8 N-m) max.
T2
S0+ S0-
PULSE OUTPUT
Type
Number of Pulses per kWh
Pulse Width
Configurable
Current
1-15mA
Isolation
Terminal Block Torque
ON
5000
/kWh
Configurable, 50 msec minimum
5-30VDC
Wire Size
I
H
Optical coupler (S0 Form)
Voltage
OK
ESC
Config
3.75 kV RMS
V1
V2
V3
Vn
S1
(I1)
S2
(I2)
S1
S2
K
Reset
S1
(I3)
ESC
OK
S2
C
24 to 14 AWG (0.2 to 2.5 mm2)
4.4 in-lb (0.5 N-m) max.
MEASUREMENT ACCURACY
Real Energy for x/1A Current
Input
G
Class 1 conforming to IEC 62053-21 and IEC 61557-12 (PMD SD):
Imax=1.2 A, ln =1 A, and Ist=0.002 A
Class B conforming to EN 50470-3: Imax=1.2 A, ln =1 A, Imin =0.01 A,
and Ist=0.002 A
Real Energy for x/5A Current
Input
Class 0.5S conforming to IEC 62053-22 and IEC 61557-12 (PMD SD):
Imax=6 A, ln =5 A, and Ist=0.005 A
©2014 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
06141
F
A. Display
B. Pulse output
C. 1A or 5A current transformer input
D. Cancellation
E. Confirmation
F. Selection
Class C conforming to EN 50470-3: Imax=6 A, ln =5 A, Imin =0.05 A, and
Ist=0.005 A
EAV71192-02
CE; UL61010-1; IEC 61010-1; IEC62053-31
Housing
The E53B3C energy meter works on a single-phase, three-phase, or three-phase + neutral network. The meter
requires 1 Amp or 5 Amp current transformers. The meter’s pulse output is configurable, with kWh values
appearing in the LCD display.
Page 1 of 7
< 2000 m
Approvals
Product Overview
ZL0125-0D
-40° to 85°C (-40° to 185°F)
Altitude of Operation
Energy Meter, Pulse Output
•
•
•
•
-25° to 55°C (-13° to 131°F) (5% to 95% RH noncondensing)
ZL0125-0D
EAV71192-02
Page 2 of 7
E
D
G. Voltage inputs
H. Energy pulse LED (500 flashes per kWh)
I. Status LED (on/off/error)
J. Locking points
K. Lockable covers
©2014 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
06141
Installation Guide
Power Monitoring
E53B3C
Installation
TM
Installation Guide
Power Monitoring
E53B3C
Wiring (cont.)
1. Disconnect power prior to the installation. Use a properly rated voltage sensing device to ensure power is off.
2. Install the meter onto standard DIN rail as shown.
TM
CT Wiring
Clearly label the device’s disconnect circuit mechanism and install it within easy reach of the operator. Use fuses/circuit
breakers that are rated for the installation voltage and sized for the available fault current. A fuse for neutral is required if the
source neutral is not grounded.
1 Phase
1 Phase, 2 Wire, L-N (I1)
V1 V2 V3 Vn
(I2)
1 Phase, 2 Wire, L-L (I3)
(I1)
V1 V2 V3 Vn
(I2)
1 Phase, 3 Wire, L-L-N
(I3)
Click!
Fuses and
Disconnect
Shorting
Block
S1
L
N
3. Wire the meter (see the Wiring section).
(I1)
V1 V2 V3 Vn
For all terminals, apply the correct torque.
I1, I2, I3
18 to 10 AWG (0.8 to 6 mm )
S0+, S0-
24 to 14 AWG (0.2 to 2.5 mm )
7.0 in-lb (0.8 N-m) max.
2
(I2)
(I3)
S2
(I1)
V1 V2 V3 Vn
(I2)
S1
S2
S1
S2
≤ 277 V L-N
≤ 480 V L-L
3 CT
(I3)
(I1)
V1 V2 V3 Vn
Fuses and
Disconnect
Shorting
Block
S1
L1
L2
L3
≤ 480 V L-L
(I1)
V1 V2 V3 Vn
Rin
Fuses and
Disconnect
L1
L2
L3
N
Radd
(opt.)
+
2 CT Fuses and
Disconnect
1 CT, Balanced Load Pulse Output Wiring
+ -
Shorting
Block
L1
L2
N
S2
(I3)
S2
S1
S2
(I3)
Shorting
Block
S1
L1
L2
L3
(I2)
S2
S1
S2
S1
S2
≤ 480 V L-L
≤ 480 V L-L
3 Phase, 4 Wire
4.4 in-lb (0.5 N-m) max.
2
S1
L1
L2
L3
4.4 in-lb (0.5 N-m) max.
2
5-30 VDC
S1
≤ 480 V L-L
Shorting
Block
Fuses and
Disconnect
24 to 14 AWG (0.2 to 2.5 mm )
Fuses and
Disconnect
Shorting
Block
L1
L2
≤ 277 V L-N
1 CT, Balanced Load 5. Configure the meter (see the Configuration section).
V1, V2, V3, Vn
S2
(I2)
3 Phase, 3 Wire
4. Reconnect power to the meter.
Wiring
Fuses and
Disconnect
(I1)
V1 V2 V3 Vn
(I2)
2 CT (I3)
Fuses and
Disconnect
Shorting
Block
S1
S2
≤ 277 V L-N
(I1)
V1 V2 V3 Vn
L1
L2
L3
N
(I2)
3 CT
(I3)
Shorting
Block
S1
S2
≤ 277 V L-N
(I1)
V1 V2 V3 Vn
Fuses and
Disconnect
L1
L2
L3
N
(I2)
(I3)
Shorting
Block
S1
S2
S1
S2
S1
S2
≤ 277 V L-N
–
ON
(I1)
V1
V2
V3
Vn
S1
(I2)
S2
S1
(I3)
S2
S1
S2
The pulse output indicates the primary consumption with consideration of transformer ratios.
The pulse output can be directly connected to a 24 VDC (< 30 VDC) input. The maximum current allowed through this
connection is 15 mA.
If VDC / Rin > 15 mA, add a resistor Radd = (VDC / 0.01) - Rin Ω
ZL0125-0D
EAV71192-02
Page 3 of 7
©2014 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
06141
ZL0125-0D
EAV71192-02
Page 4 of 7
©2014 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
06141
Installation Guide
Power Monitoring
E53B3C
Configuration
TM
Installation Guide
Power Monitoring
E53B3C
Configuration (cont.)
Initial Clock Setting
When the meter is first powered, set the date and time as shown.
Date & Time
0010
OK
Date
Set?
OK
Time
01-Jan-2000
DD-MM-YYYY
OK
Configuration Menu
All parameters in the configuration menu are modified in one of two ways.
1. Select a value from a pre-set list: use the down button to scroll through the parameter values until the desired value is
reached. Press OK to confirm the selected value.
ESC
Password
TM
OK
Date & Time
00:00
hh:mm
OK
Save Settings?
Total Active E
OK
1234.5
kWh
2. Modify a numerical value: the digit on the far right is selected first. Use the down button to modify the selected digit.
Press OK to move to the next digit. Repeat for all available digits, then press OK to confirm the selected value.
When power is interrupted, the date and time are reset. When power is restored, the LCD shows the screen used to set the date
and time. All other time changes (e.g. standard time to daylight savings time) are performed manually in the configuration
menu.
To cancel the current entry, press the ESC button. This cancels the modification and the screen reverts to the last saved value.
LED Blink Codes
Password
Energy Pulse LED
Green LED
OK
Description
ESC
Off
Off
Meter is not powered
On
On for 1 sec, then off
Meter is on but is not counting pulses
On
Flashing
Meter is on and is counting pulses
Off
On
Internal error, counting is stopped
Flashing
Flashing
Abnormal operation, but meter is counting
Wiring
OK
OK
Wiring\Type
OK
Wiring\CT
Wiring\CT
Wiring
OK
Save settings?
3PH4W
1PH2W L-N
...
CT Ratio
OK
..\CT Secondary
1 CT on I1
2 CTs on I1, I3
...
OK
..\CT Primary
OK
CT Ratio
A - Cancel and return to
the previous screen
B - Reset the settings
to their defaults,
except for the
password, and
restart the meter.
OK
Save settings?
5
1
Configuration Mode
Many features can be configured or adjusted while the meter is in service. The configuration menu shows how to enter each
mode and select the desired option.
Frequency
OK
1
0 - 99999
OK
Frequency
Frequency
OK
Date
OK
Save settings?
50
60
Enter the menu by pressing the ESC and OK buttons as shown:
Date
OK
OK
Date
Config
1
> 2s
Time
Total Active E
OK
A
2 ...
23 Apr 2011 12:00
E
F
kWh
1
C
D
G
..\In. Pulse Const.
00500
H
OK
Time
Time
OK
Save settings?
2 ...
hh:mm
B
1234.5
Screen in
Configuration Mode
Save settings?
DD-MM-YYYY
The display screen is shown below.
Screen in
Normal Mode
2 ...
Pulse Output
A. Measurement/Parameter
B. Value/Setting
C. Date and time
D. Units
E. Scroll through screens or a list of options
F. Confirm entry or access more screens
G. Cancel and go back to previous screen
H. Configuration mode icon
OK
..\Pulse Constant
OK
100
200
...
Contrast
OK
..\Pulse Width
OK
Pulse Output
OK
Save settings?
100
200
...
OK
Contrast
Contrast
OK
Password
OK
Save settings?
1
2
...
Password
OK
1
Overriding!
OK
Password
Save settings?
2 ...
1 - 9999
Reset Config
OK
Reset Config
OK
Confirm & Reboot?
After performing basic configuration, navigate to the real-time data screens and verify that the readings are correct.
ZL0125-0D
EAV71192-02
Page 5 of 7
©2014 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
06141
ZL0125-0D
EAV71192-02
Page 6 of 7
©2014 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
06141
Installation Guide
Power Monitoring
E53B3C
TM
Troubleshooting
Code
-
Push buttons do not function.
101
Metering stops due to an EEPROM error. Press OK to
display total energy consumption.
Metering stops due to a lack of a calibration table. Press
OK to display total energy consumption.
Metering continues. Mismatch between frequency
settings and frequency measurements.
Metering continues. Mismatch between wiring settings
and wiring inputs.
Metering continues. Phase sequence reversed.
Restart the energy meter by powering off and powering on
again.
Enter configuration mode and implement Reset Config.
201
202
203
204
205
206
207
EAV71192-02
Page 7 of 7
Solution
Check and adjust LCD contrast.
102
ZL0125-0D
Description
LCD display is not visible.
Enter configuration mode and implement Reset Config.
Correct the frequency settings according to the nominal
frequency of the power system.
Correct the wiring settings according to the wiring inputs.
Check the wire connections and correct the wiring settings if
needed.
Check wire connections.
Metering continues. Total active energy negative due to
incorrect voltage and current conditions.
Metering continues. Date and Time have been reset due to Set the Date and Time.
a loss of power.
Metering continues. Pulse is missing due to overload on Check the energy pulse output settings.
energy pulse output.
Metering continues. Abnormal internal clock function.
Restart the energy meter by powering off and powering on
again then reset the date and time.
©2014 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
06141
Installation Guide
Power Monitoring
E53B3C
TM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement