NW2350-2352 Manual
Pump Guard
With Pool Cover Pump Guard included
Manual Models
• Capacity is 1250 or 2450 gallons per hour
• Manual operation
• Assorted adapter fittings included
• 33’ power cord
• Pump guard
Automatic Models
• Capacity is 1250 or 2450 gallons per hour
• Manual operation
• Assorted adapter fittings included
• 33’ power cord
• Pump guard
page 1
WARRANTY
SUBMERSIBLE PUMP UNIVERSAL INSTRUCTION MANUAL
Your submersible pump is guaranteed to be in perfect condition when it leaves our factory. It is
warranted against defective materials and workmanship for a period of 12 months from the date of
purchase from owner.
Congratulations on your purchase of a submersible pump. Your pump has been manufactured to the highest
standards of workmanship and materials. It has been engineered to give you many years of exceptional performance. This instruction manual is designed to cover all models of pumps and not all features applicable to all
pumps.
If any pump should fail for either of above two reasons and is still within the warranty period, it will be
repaired or replaced at the option of manufacturer as the sole remedy of the buyer.
Your pump has been carefully package inspected and factory tested to insure safe operation and that the
pump performs as well for you as it did in the factory. Your pump housing is constructed of durable polymer
material. The housing provides protective shield for the motor. UNDER NO CIRCUMSTANCES SHOULD YOU
OPEN THE CASE AND EXPOSE THE MOTOR. IF THE CASE IS OPENED, THEN THE WARRANTY EXPRESSED IN
THIS MANUAL WILL BE VOID.
All defective product returned under warranty will be fully inspected to determine the cause of failure
before warranty is approved. Defective product can be returned to an AUTHORIZED SERVICE CENTER
with a brief explanation of the problem. If there is no apparent signs of customer abuse the unit may
be repaired, replaced or returned to the factory for warranty inspection. Any and all freight charges
incurred in returning the unit to the factory will be the sole responsibility of the purchaser.
Read all instructions carefully before attempting to install, operate or service the pump. Know the pump
application, limitations and potential hazards, protect yourself and others by observing all safety information.
Failure to comply with instructions could result in personal injury and / or property damage! Retain this manual
for future reference.
SAFETY GUIDELINES WARNING
DISCLAIMER: THE FOREGOING WARRANTY IS AN EXCLUSIVE WARRANTY IN LIEU ANY
OTHER EXPRESS WARRANTIES. ANY IMPLIED WARRANTIES (INCLUDING
BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE) TO THE EXTENT EITHER
IMPLIES TO A PUMP SHALL BE LIMITED IN DURATION TO THE PERIODS OF
THE EXPRESS WARRANTIES GIVEN ABOVE.
1. Make sure that the pump is disconnected from the power source before attempting to service or remove
any component.
2. Do not use to pump flammable liquids or explosive fluids such as gasoline, fuel oil, kerosene, etc. Do not
use in explosive atmospheres. Pump should ONLY be used with liquids compatible with pump component
materials.
3. Do not handle pump with wet hands or when standing on a wet or damp surface or in water.
4. Your pumps is supplied with a grounding conductor and/or grounding-type attachment plug. To reduce the
risk of electric shock, be certain that it is connected to a properly grounded grounding-type receptacle.
5. In any installation where property damage and/or personal injury might result from an
inoperative or leaking pump due to power outages, discharge line blockage, or any other reason, a backup
system(s) and /or alarm should be used.
6. Support your pump and piping when assembling and when installed.
Failure to do so may cause pipe to break, pump to fail, motor bearing failures, etc.
page 2
page 3
ELECTRICAL CONNECTION WARNING
SERVICE INSTRUCTIONS WARNING
1. Check your pump label for proper voltage required. Do not connect to voltage other than that shown. The
pump can be connected to any shock proof plug (ground fault interrupter circuit) which has been installed
according to electrical code. The plug must have a supply voltage of 110V-60 Hz and a circuit of a minimum of
6 amps.
2. When the pump is to be used near swimming pools or garden ponds and in their area the power supply
must be equipped with a ground –fault interrupter circuit with a nominal trip current of a maximum of .30mA.
The pump must not be operated while people are in the swimming pool or in the garden pond. Consult your
electrician.
MAKE SURE THE PUMP IS DISCONNECTED
FROM THE POWER SOURCE BEFORE ATTEMPTING
TO SERVICE OR CLEAN THE PUMP!
1. The motor housing of your pump is completely sealed and requires no service. Disassembly of the motor
housing or alteration of the power cord voids all warranty.
2. Your pumps should be cleaned out with fresh, clean water after every use.
3. Your pump is supplied with a 3-prong electrical plug, the third prong is to ground the pump to prevent
possible shock hazard. DO NOT REMOVE the third prong. A separate branch circuit is recommended. DO NOT
use an extension cord. Do not cut the plug from the cord. If the plug is cut or the cord shortened, then this
action will void the warranty.
4. The electrical connection must be protected from moisture.
PUMP OPERATION WARNING
1. Your pump cannot be operated in water with a temperature in excess of
122 degrees Fahrenheit.
2. Place pump in water at least 3/4 inch deep to begin pumping. Pump should be totally submerged for proper
cooling of the motor when the pump is operated for extended periods.
3. If you purchased a pump that is equipped with an adjustable “go flow” high water sensor, the pump will
automatically turn on once the internal sensor detect water at the level you have selected. The pump will automatically turn off once the water level has gone below the selected height of the “no flow” setting you have
selected. Always select a higher level for “go flow” setting than the “no flow” setting. This will help prevent the
pump from running dry and voiding the warranty. Never set the “go Flow” and “no flow” at the same level, this
will cause the pump to run dry and void the warranty.
4. If your pump is not equipped with the smart flow sensor it must be turned on and off manually. Care must
be taken to not let the pump run dry. (without fluid) The pump is designed to be cooled by pumping fluid. Seal
damage, bearing damage and motor failure can result if the pump is allowed to run dry.
5. When first starting your pump you should run water into the pump until the pump starts. Allow the pump to
operate through several on/off cycles.
6. If the pump is going to be idle for period of time, follow the cleaning instructions outlined in this manual. Do
not let the pump freeze in winter time. This may cause cracking or distortion that may destroy the pump and
void the warranty.
7. For best performance use the supplied collapsible hose, attach to appropriate sized fitting and secure with
clamp. Make sure that hose is fully extended so that water can flow freely.
page 4
page 5
AUTOMATIC ON/OFF SENSORS
Your new Submersible Pump is fully assembled and ready to use
START GO-FLOW STOP-FLOW SYSTEM
Follow these simple instructions to begin the operation of your submersible pump. Be sure to read all the
instructions and warnings before you begin the operation of the pump to help prevent personal injury or
property damage.
1. Set the release end of the discharge hose to the area you want to move the unwanted water. Be sure to
check the area for possible damage/flooding before you begin pump operation.
2. Set the green “GO FLOW” level indicator to the desired level of water you want for automatic activation
of your pump. This is the height you want the water to reach before the pump switches on. Once the water
reaches the set level the pump will start and continue until the water level decreases to the level set on the red
“NO FLOW” indicator.
3. Set the red “NO FLOW” indicator to the water height you want to pump to automatically turn off (stop
pumping) Once the water level reaches the height set on the “NO FLOW” setting and turns off, it will not turn
on again until the water reaches the level set on the “GO FLOW” indicator.
4. Note: Do not set the red (No Flow) and green (Go Flow) indicators too closely. This will result in the pump not
functioning properly as well as running dry. If this happens the motor will overheat and void your warranty.
5. Place your pump in its desired location. Always use the carry handle to transport your pump. NEVER carry
your pump by the cord or hose connection.
6. Plug the cord into an approved electrical outlet (as outlined in this manual) and begin operation.
7. It is recommended that you use the SteadyMate pump guard for your submersible pump when you use
the pump for removing excess water from a swimming pool cover. It will increase the pumps stability and
performance.
page 6
page 7
Your new Submersible Pump is fully assembled and ready to use
Follow these simple instructions to begin the operation of your submersible pump. Be sure to read all the
instructions and warnings before you begin the operation of the pump to help prevent personal injury or
property damage.
32 Foot
Power
Cord
1. Set the release end of the discharge hose to the area you want to move the unwanted water.
Be sure to check the area for possible damage/flooding before you begin pump operation.
2. Place your pump in its desired location. Always use the carry handle to transport your pump. NEVER
carry your pump by the cord or hose connection.
3. Plug the cord into an approved electrical outlet (as outlined in this manual) and begin operation.
4. It is recommended that you use the SteadyMate pump guard for your submersible pump when you use
the pump for removing excess water from a swimming pool cover. It will increase the pumps stability and
performance.
New Low-Profile Base Guard
Included with this pump
page 8
page 9
Pump Guard
•
•
•
•
•
Easy Twist-n-Lock Design
Removeable
Increased Stability
Curved Bottom for Uneven Surfaces
Multiple Inlet Openings
If you plan on using your pump to remove water from
a swimming pool cover, our included Pump Guard is
designed to add stability and protect your pump from
leaves and debris.
Easy to twist / lock installation and removal adds even
more versatility to your pump.
page 10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising