Schwinn Evolution SR, spin bike Assembly instructions

The Schwinn Evolution and Evolution SR spin bikes are designed for indoor cycling workouts. They feature a durable steel frame, adjustable resistance, and a comfortable seat. The Evolution SR model includes a red seat and a unique brake pad system for a smoother ride.

PDF Download

Document

Evolution / Evolution-SR
ASSEMBLY INSTRUCTIONS
SCHWINN
SCHWINN EVOLUTION - PACKAGE COMPONENTS LIST
Ref. # Description Qty.
1. Frame 1
25. Handle Bar 1
27. Seat Slider Assembly with Saddle 1
A Front Stabilizer Bar with Wheels and Feet 1
B Rear Stabilizer Bar with Feet 1
Small Parts Box 1
67 Water Bottle Cage 2
Small Part Box Contents
42. Pedals with Toe Clips &amp; Straps (Left &amp; Right) 1 Pair
44. Pop Pin Assembly for Head Tube 1
39. 13mm Hex Bolt 4
50. Flat Washer 8
51. 13mm Lock Nut 4
Tools Supplied
Stamped Steel 13/14/15/17mm Combination Wrench 1
5mm Hex Wrench 1
3mm Hex Wrench 1
Prior to assembly of the product, remove all components from the packaging and check them
against the packaged components list supplied above. Once you are certain that all the necessary
parts have been supplied, begin with the first assembly step.
Tools Needed
5mm Hex Wrench
3mm Hex Wrench o
Stamped Steel
Combination wrench
17/15 O 13/14
Adjustable wrench (not included)
2 Evolution / Evolution-SR SCHWINN
MATERIALS &amp; TOOLS
Front Rear
Ref. # Description Qty
1 Frame 1
A Front Stabilizer Bar with Wheels and Feet 1
B Rear Stabilizer Bar with Feet 1
39 13mm Hex Bolt 4
50 Flat Washer 8
51 13mm Lock Nut 4
Tools Required
Stamped Steel Combination Wrench 1
Adjustable wrench or 13mm Socket (not supplied) 1
5mm Hex Tool 1
&gt;
Position the Front Stabilizer Bar (A) under the frame bracket as shown in the illustration.
B. Make sure the adjustable feet are on the bottom and the transport wheels are facing up and
toward the front of the bike.
CAUTION:
IT IS VERY IMPORTANT TO APPLY GREASE TO THE 13mm HEX BOLT (39) PRIOR TO
MOUNTING THE 13mm LOCKNUT (51) THIS WILL ENSURE THAT YOU CAN REMOVE
THE NUT AT A LATER DATE.
C. Attach Front Stabilizer Bar (A) to Frame (1) using two hex bolts (39), four washers (50), and two
lock nuts (51). Tighten hardware firmly but do not over tighten as deformation of the stabilizer
tube may occur
At this time make sure that the adjustable feet with lock nuts are screwed fully into the stabilizer.
Position the Rear Stabilizer Bar (B) under the frame bracket as shown in the illustration.
Make sure the adjustable feet are on the bottom.
Attach Rear Stabilizer Bar (B) to Frame (1) using two hex bolts 39), four washers (50), and two
lock nuts (51). Tighten hardware firmly but do not over tighten as deformation of the stabilizer
tube may occur
H. At this time make sure that the adjustable feet with lock nuts are screwed fully into the stabilizer.
&copy; mmo
SCH VWVWINN Evolution / Evolution-SR 3
MATERIALS &amp; TOOLS
Ref. # Description Qty
1 Frame 1
44 Pop Pin Assembly for Head Tube 1
25 Handle Bar 1
44, 27, 45 Seat Slider Assembly (Pre-Assembled) 1
26 Seat Post 1
67 Bottle Cage 2
Tools Required
Adjustable wrench (not supplied) 1
A. Remove the Pop Pin Assembly (44) from the small parts bag and add some grease to the threads
B.
C.
of the large 21mm nut that will screw into the head tube boss on the bike.
Thread the Pop Pin Assembly into the head tube boss using a large adjustable wrench,
tighten firmly.
Using your hand grab the T-handle of the Pop Pin, turn it counter-clockwise to make sure it is free
of the securing threads and can be pulled freely.
Insert the Handle Bar (25) into the head tube of the bike while pulling the Pop Pin back. Insert the
Handle Bar to the desired height and release the Pop Pin. Make sure the Pop Pin settles into one
of the securing holes in the Handle Bar tube. Turn the Pop Pin clockwise threading it into the Pop
Pin Assembly and hand tighten. This will secure the Handlebar at the desired height.
Using your hand, grab the T-handle of the Pop Pin attached to the seat tube, turn it counter-
clockwise to make sure it is free of the securing threads and can be pulled freely.
Insert the Seat Post (26) into the seat tube while pulling the Pop Pin back. Insert the Seat Post
to the desired height and release the Pop Pin. Make sure the Pop Pin settles into one of the
securing holes in the Seat Post tube. Turn the Pop Pin clockwise threading it into the Pop Pin
Assembly and hand tighten. This will secure the Seat Post at the desired height.
. The Seat Slider Assembly (44,27,45) has been pre-assembled at the factory. Insert the front
(saddle nose side) of the Seat Slider Assembly into the back of the seat post slider tube (hori-
zontal tube at the top). There is a small spring pin at the rear of the slider tube on the Seat
Post that must be depressed to allow the Seat Slider Assembly to fully attach to the Seat Post,
This can be can be accomplished by laying the Seat Slider Assembly on the spring pin, push
down on the entire Seat Slider Assembly so that the spring pin is depressed. While pulling
down on the Pop Pin push the Seat Slider Assembly onto the seat post slider tube. When the
Seat Slider has moved far enough forward the spring pin will pop out of the back. This
secured the Seat Slider to the seat post tube and prevents it from inadvertently separating from
the seat post slider tube.
. Using a 3mm Hex Wrench, remove the screws pre-assembled to the fork legs of the bike.
Position the bottle cage (67) on the side of the bike and tighten the screws securely to the fork leg.
4 Evolution / Evolution-SR SCHWINN
MATERIALS &amp; TOOLS / INITIAL SETUP ADJUSTMENTS
Ref. # Description Qty
1 Frame 1
42 Pedals with Toe Clips &amp; Straps (Left &amp; Right) 1 Pair
Tools Required
Stamped Steel Combination Wrench 1
A. Remove pedals (42) from the small parts box and look at the ends of
the pedal threads. You will notice that each pedal is market with an &quot;R&quot;
or an &quot;L&quot; on the very end of the spindle past the threads. This mark
indicates which side of the bike the pedal is intended to mount. This is
important since the thread directions are different for each pedal.
B. Locate the pedal that has the &quot;R&quot; on the spindle. This pedal is for the right side crank arm of the
bike (chain guard side) and is right hand threaded (turn clockwise to tighten). It is a good idea to
apply grease to the threads before attaching them to the crank, this will assure that they can be
removed in the future. Using the supplied Combination Wrench thread the right pedal on to the
crank arm, tighten firmly.
C. Locate the pedal that has the &quot;L&quot; on the spindle. Follow the directions in step B. however, you will
need to turn the spindle left (counter-clockwise) to tighten as the &quot;L&quot; spindle is reverse threaded.
Prior to first using the Schwinn Evolution bike it is a good idea to
follow these initial set up steps.
A. Move bike into its final location. Confirm that all four feet are firmly in contact with the floor and that
the bike is stable. If any of the feet are not making full contact it is recommended that you adjust
them by turning the entire foot assembly counter-clockwise which will extend it further from the sta-
bilizer bar. Once the foot is in full contact and the bike is stable, thread the jam nut clockwise until
it comes into contact with the stabilizer at the point the foot assembly threads in. Tighten the jam
nut snug using an adjustable wrench. This will secure the foot at the desired height.
B. With the resistance adjustment knob turned fully in the counter-clockwise position (no brake con-
tact with flywheel) it is recommended that you soak the brake pads with Schwinn Fit-Tech Lube.
This will extend the life of the brake pads and assure a smooth resistance interface with the fly-
wheel,
C. Once the pads are lubricated it is recommended that you tighten the resistance adjustment knob
clockwise to tighten the brake pads against the flywheel surface. Do this until the brake pads are firm-
ly clamped against the flywheel. This will set the brake parts and give the springs some initial com-
pression. This process will also assure that the Fit-Tech Lube penetrates the entire brake pad surface.
D. Confirm that the Saddle is positioned in the desired location on the saddle mounting bracket. If the
angle of the saddle or the fore/aft position of the saddle needs to be adjusted, use the Combination
Wrench to loosen the 14mm nuts on either side of the saddle mounting bracket. This will allow you
to adjust the tilt angle and fore/aft position of the saddle. Once in the correct position, tighten both
14mm nuts on the saddle mounting bracket with the Combination Wrench.
That's it! Initial set up is complete and you can now enjoy all these
features and quality of you new Scwhinn Evolution Bike!
SCH VWVWINN Evolution / Evolution-SR 5
EVOLUTION ASSEMBLY DRAWING AND REPLACEMENT PARTS
EVOLUTION Dwg# Description Part #
1 FRAME 84985
2 CHAINGUARD (INNER) 84986
3 CHAINGUARD (OUTER) 84982
4 SHROUD (RIGHT) 80011
5 SHROUD (LEFT) 80010
6 RUBBER RING FOR OUTER CHAINGUARD 80003
7 STAINLESS STEEL AXLE NUT 3/8X26TX11T 95149
8 CHAIN ADJUST BRACKET (LEFT) 84987
9 SLEEVE FOR FRAME 80001
10 STAINLESS CHAIN TEN. BOLT M6X1.0X60L 84988
11 BOTTLE HOLDER 80012
12 CHAIN ADJUST BRACKET (RIGHT) 84989
13 RUBBER FRAME GUARD 80014
14 STAINLESS SELF-TAPPING SCREW M5X12L 80040
16 PROTECTIVE PLASTIC STICKER (B) 80041
17 PROTECTIVE PLASTIC STICKER (A) 80042
18 MACHINE SCREW M5X.08X12L SS 84957
19 EMERGENCY BRAKE LEVER 80009
20 B.B. SET, OVERDRIVE W/BOLTS 68X113L. 84990
21 STAINLESS WASHER 16 X 6.5 X1 95431
22 RIGHT CRANK W/SPOCKET, ISIS M12 80034
23 LEFT CRANK ARM | ISIS 80035
24 STAINLESS HEX HEAD BOLT MoX1.0X12L 956432
25 HANDLEBAR BLACK TEXTURED 84991
26 SEAT POST, STAINLESS 84992
27 SEAT ADJUSTMENT BRACKET 84993
28 SLEEVE FOR SEAT SLIDER 80002
29 SEAT RETAINING PIN 80006
30 RETAINING PIN COVER 80013
31 RESISTANCE ASSEMBLY 80008
32 TENSION ADJUSTING KNOB 80017
33 TENSION KNOB RING 80005
34 ROD CARRIER 80007
35 NUT FOR RES. ASSM. M6x1.0 SS 95456
36 PLASTIC BALL RING 80004
37 REAR STABILIZER 84984
38 HEX NUT FOR LEVELING FEET 3/8 80016
39 STAINLESS HEX HEAD BOLT M8X1.25X50L 80030
40 FRONT STABILIZER 84983
41 BOLT TRANSPORT WHL M8X1.25X45L SS 92218
42 PEDALS 9/16&quot; 95129
43 FRAME PLUG FOR BRAKE ASSM. 92206
44 T-HANDLE POP PIN DOUBLE LEAD 84994
45 SEAT, 7777-1, BLACK 93092
46 YELLOW PLASTIC BUSHING SET OF 2 92204
47 SQUARE NUT 9802?
48 BRAKE PADS 92874
49 | EVELER FOOT 84995
50 WASHER 19 X 8.5 X TMM SS 95426
51 SCREW NUT M8 X 1.25 SS 91731
52 TRANSPORTATION WHEEL 92220
53 CHAIN 106L 1/2X3/32&quot; 80043
54 FLYWHEEL COMPLETE SET 84996
55 HUB SHELL PLASTIC COVER 92451
56 SPOCKET 16t (BLACK) 84997
57 SPROCKET WASHER 95457
58 LOCK NUT 95450
60 AXLE SET 95125
61 BADGE SCHWINN LOGO 33MM 80047
03 CRANK BOLT - TEA M12 80044
66 BOTTLE CAGE BOLT M5X.8 X16L 95428
67 BOTTLE CAGE 84998
68 RUBBER FRAME GUARD STRIP 84999
69 BADGE SCHWINN LOGO 40MWM 80048
O [OA (TES y INN
EVOLUTION-SR ASSEMBLY DRAWING AND REPLACEMENT PARTS
EVOLUTION-SR Dwg# Description Part #
1 FRAME 84985
2 CHAINGUARD (INNER) 84986
3 CHAINGUARD (OUTER) 84982
4 SHROUD (RIGHT) 80011
5 SHROUD (LEFT) 80010
6 RUBBER RING FOR OUTER CHAINGUARD 80003
7 STAINLESS STEEL AXLE NUT 3/8X26TX11T 95149
8 CHAIN ADJUST BRACKET (LEFT) 84987
9 SLEEVE FOR FRAME 80001
10 STAINLESS CHAIN TEN. BOLT M6X1.0Xo0L 84988
11 BOTTLE HOLDER 80012
12 CHAIN ADJUST BRACKET (RIGHT) 84989
13 RUBBER FRAME GUARD 80014
14 STAINLESS SELF-TAPPING SCREW M5X12L 80040
16 PROTECTIVE PLASTIC STICKER (B) 80041
17 PROTECTIVE PLASTIC STICKER (A) 80042
18 MACHINE SCREW M5X.08X12L SS 84957
19 EMERGENCY BRAKE LEVER 80009
20 B.B. SET, OVERDRIVE W/BOLTS 68X113L 84990
27 STAINLESS WASHER 16 X 6.5 X7 95431
22 RIGHT CRANK W/SPOCKET, ISIS M12 80034
23 LEFT CRANK ARM | ISIS 80035
24 STAINLESS HEX HEAD BOLT M6X1.0X12L 95432
&gt; \ \ 25 HANDLEBAR BLACK TEXTURED 84991
9 i &amp; 02 20 SEAT POST, STAINLESS 84992
| 27 SEAT ADJUSTMENT BRACKET 84993
28 SLEEVE FOR SEAT SLIDER 8000?
29 SEAT RETAINING PIN 80006
A € 30 RETAINING PIN COVER 80013
va, 31 RESISTANCE ASSEMBLY 80008
a a&gt; 32 TENSION ADJUSTING KNOB 80017
NL Se 33 TENSION KNOB RING 80005
ON = — 34 ROD CARRIER 80007
=&gt; 35 NUT FOR RES. ASSM. M6X1.0 SS 95456
36 PLASTIC BALL RING 80004
37 REAR STABILIZER 84984
38 HEX NUT FOR LEVELING FEET 3/8 80016
39 STAINLESS HEX HEAD BOLT M8X1.25X50L 80030
40 FRONT STABILIZER 84983
47 BOLT TRANSPORT WHL M8X1.25X45L SS 92218
42 PEDALS 9/16&quot; 95129
| 43 FRAME PLUG FOR BRAKE ASSM. 92206
| al 44 T-HANDLE POP PIN DOUBLE LEAD 84994
&laquo;GE 45 SEAT, 7777-1, RED 92202
5 46 YELLOW PLASTIC BUSHING SET OF 2 92204
47 SQUARE NUT 9802?
48 BRAKE PADS 92874
49 LEVELER FOOT 84995
50 WASHER 19 X 8.5 X TMM SS 95426
57 SCREW NUT M8 X 1.25 SS 91731
52 TRANSPORTATION WHEEL 92210
53 CHAIN 106L 1/2X3/32&quot; 80043
54 FLYWHEEL COMPLETE SET 92207
55 FLANGED HUB LOCK NUT 92214
56 BEARING RETAINER RING 92458
57 HUB SHELL PLASTIC COVER 92451
58 INNER ADJ SR PLATE 9245?
59 CONICAL SPRING 92208
60 INTERFACING PLATE TO BRAKE PADS 92453
67 SR BRAKE PAD SET, WHITE U.H.P. 92213
62 HUB SPOCKET W/BEARING 98419
63 CRANK BOLT - 1EA M12 80044
64 AXLE SET 98414
65 BADGE SCHWINN LOGO 33MM 80047
66 BOTTLE CAGE BOLT M5X.8 X16L 95428
67 BOTTLE CAGE 84998
08 RUBBER FRAME GUARD STRIP 84999
69 BADGE SCHWINN LOGO 40MM 80048
SCHWINN
Evolution / Evolution-SR 7
Nautilus Health € Fitness Group - 1886 Prairie Way Louisville, CO 80027
O 2003 Nautilus, Inc. &raquo; SCHWINNFITNESS.COM
1.800.864.1270
SCHWINN.
">

Hello! I am an AI chatbot specifically trained to assist you with the Schwinn Evolution SR spin bike Assembly instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key Features

Adjustable Resistance
Comfortable Seat
Durable Steel Frame
Transport Wheels
Adjustable Feet
Emergency Brake Lever
Bottle Cage

Frequently asked questions

How do I adjust the resistance on the Schwinn Evolution spin bike?

To adjust the resistance, turn the tension adjustment knob clockwise to increase resistance and counterclockwise to decrease resistance.

What is the difference between the Evolution and Evolution SR models?

The Evolution SR model features a red seat and a unique brake pad system for a smoother ride.

How do I adjust the height of the seat?

To adjust the height of the seat, use an adjustable wrench to loosen the 14mm nuts on either side of the saddle mounting bracket. Once in the correct position, tighten both 14mm nuts on the saddle mounting bracket with the Combination Wrench.

How do I install the pedals?

The pedals are marked with an 'R' for right and an 'L' for left. Attach the right pedal to the right crank arm (chain guard side) and the left pedal to the left crank arm. Make sure the pedal threads are greased before attaching.