H110M-DGS
H110M-DGS
Version 1.0
Published October 2015
Copyright©2015 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for a particular
purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
Contents
Chapter 1 Introduction
1
1.1 1
Package Contents
1.2 Specifications
2
1.3 Motherboard Layout
5
1.4 I/O Panel
7
Chapter 2 Installation
2.1 Installing the CPU
9
10
2.2 Installing the CPU Fan and Heatsink
13
2.3 Installing Memory Modules (DIMM)
14
2.4 Expansion Slots (PCI Express Slots)
16
2.5 Onboard Headers and Connectors
17
Chapter 3 Software and Utilities Operation 21
3.1 21
Installing Drivers
3.2 ASRock Live Update & APP Shop
22
3.2.1 UI Overview
22
3.2.2 Apps
23
3.2.3 BIOS & Drivers
26
3.2.4 Setting
27
3.3 28
Enabling USB Ports for Windows® 7 Installation
Chapter 4 UEFI SETUP UTILITY
31
4.1 31
Introduction
4.2 EZ Mode
32
4.3 Advanced Mode
33
4.3.1 UEFI Menu Bar
33
4.3.2 Navigation Keys
34
4.4 Main Screen
35
4.5 OC Tweaker Screen
36
4.6 Advanced Screen
44
4.6.1 CPU Configuration
45
4.6.2 Chipset Configuration
47
4.6.3 Storage Configuration
49
4.6.4 ACPI Configuration
50
4.6.5 USB Configuration
52
4.6.6 Trusted Computing
53
4.7 Tools
54
4.8 Hardware Health Event Monitoring Screen
57
4.9 Security Screen
59
4.10 Boot Screen
60
4.11 Exit Screen
63
H110M-DGS
Chapter 1 Introduction
Thank you for purchasing ASRock H110M-DGS motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the
motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the software and utilities. Chapter 4 contains the configuration guide of
the BIOS setup.
Because the motherboard specifications and the BIOS software might be updated, the
content of this documentation will be subject to change without notice. In case any modifications of this documentation occur, the updated version will be available on ASRock’s
website without further notice. If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. You
may find the latest VGA cards and CPU support list on ASRock’s website as well. ASRock
website http://www.asrock.com.
1.1 Package Contents
ASRock H110M-DGS Motherboard (Micro ATX Form Factor)
ASRock H110M-DGS Quick Installation Guide
ASRock H110M-DGS Support CD
2 x Serial ATA (SATA) Data Cables (Optional)
1 x I/O Panel Shield
English
•
•
•
•
•
1
1.2 Specifications
English
2
Platform
• Micro ATX Form Factor
• Solid Capacitor design
CPU
• Supports 6th Generation Intel® CoreTM i7/i5/i3/Pentium®/
Celeron® Processors (Socket 1151)
• Supports CPU up to 95W
• Supports Intel® Turbo Boost 2.0 Technology
Chipset
• Intel® H110
Memory
•
•
•
•
•
Dual Channel DDR4 Memory Technology
2 x DDR4 DIMM Slots
Supports DDR4 2133 non-ECC, un-buffered memory
Max. capacity of system memory: 32GB
Supports Intel® Extreme Memory Profile (XMP) 2.0
Expansion
Slot
• 1 x PCI Express 3.0 x16 Slot (PCIE2: x16 mode)*
* Supports NVMe SSD as boot disks
• 1 x PCI Express 2.0 x1 Slot
Graphics
*Intel® HD Graphics Built-in Visuals and the VGA outputs can
be supported only with processors which are GPU integrated.
• Supports Intel® HD Graphics Built-in Visuals : Intel® Quick
Sync Video with AVC, MVC (S3D) and MPEG-2 Full
HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics 510/530
• Pixel Shader 5.0, DirectX 12
• Max. shared memory 1792MB
• Supports DVI-D with max. resolution up to 1920x1200 @
60Hz
• Supports Accelerated Media Codecs: HEVC, VP8, VP9
• Supports HDCP with DVI-D Port
• Supports Full HD 1080p Blu-ray (BD) playback with DVI-D
Port
H110M-DGS
• 7.1 CH HD Audio (Realtek ALC887 Audio Codec)
* To configure 7.1 CH HD Audio, it is required to use an HD
front panel audio module and enable the multi-channel audio
feature through the audio driver.
• Supports Surge Protection (ASRock Full Spike Protection)
• ELNA Audio Caps
LAN
•
•
•
•
•
PCIE x1 Gigabit LAN 10/100/1000 Mb/s
Realtek RTL8111GR
Supports Wake-On-WAN
Supports Wake-On-LAN
Supports Lightning/ESD Protection (ASRock Full Spike
Protection)
• Supports LAN Cable Detection
• Supports Energy Efficient Ethernet 802.3az
• Supports PXE
Rear Panel
I/O
•
•
•
•
1 x PS/2 Mouse Port
1 x PS/2 Keyboard Port
1 x DVI-D Port
4 x USB 2.0 Ports (Supports ESD Protection (ASRock Full
Spike Protection))*
* ACPI wake-up function is supported on USB23 ports only.
• 2 x USB 3.0 Ports (Supports ESD Protection (ASRock Full
Spike Protection))
• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
• HD Audio Jacks: Line in / Front Speaker / Microphone
Storage
• 4 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and
Hot Plug
Connector
•
•
•
•
1 x TPM Header
1 x Chassis Intrusion and Speaker Header
1 x CPU Fan Connector (4-pin) (Smart Fan Speed Control)
1 x Chassis Fan Connector (4-pin) (Smart Fan Speed Control)
• 1 x 24 pin ATX Power Connector
• 1 x 8 pin 12V Power Connector
• 1 x Front Panel Audio Connector
English
Audio
3
• 1 x USB 2.0 Header (Supports 2 USB 2.0 ports) (Supports
ESD Protection (ASRock Full Spike Protection))
• 1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports
ESD Protection (ASRock Full Spike Protection))
BIOS
Feature
•
•
•
•
AMI UEFI Legal BIOS with multilingual GUI support
ACPI 5.0 Compliant wake up events
SMBIOS 2.7 Support
CPU, GT_CPU, DRAM, PCH 1.0V, VCCIO, VCCSA Voltage
Multi-adjustment
Hardware Monitor
• CPU/Chassis temperature sensing
• CPU/Chassis Fan Tachometer
• CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by
CPU temperature)
• CPU/Chassis Fan multi-speed control
• CASE OPEN detection
• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore
• Microsoft® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64bit
* To install Windows® 7 OS, a modified installation disk with
xHCI drivers packed into the ISO file is required. Please refer to
page 28 for more detailed instructions.
* For the updated Windows® 10 driver, please visit ASRock’s
website for details: http://www.asrock.com
OS
Certifications
• FCC, CE, WHQL
* For detailed product information, please visit our website: http://www.asrock.com
English
Please realize that there is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using third-party
overclocking tools. Overclocking may affect your system’s stability, or even cause damage to
the components and devices of your system. It should be done at your own risk and expense.
We are not responsible for possible damage caused by overclocking.
4
H110M-DGS
1.3 Motherboard Layout
2
1
3
PS 2
Mouse
PS2
Keyboard
CPU_FAN1
4
CHA_FAN1
ATX12V1
ATXPWR1
USB 2.0
Top:
T: USB0 RJ-45
B: USB1
DDR4_B1 (64 bit,288-pin module)
DDR4_A1 (64 bit, 288-pin module)
DVI1
USB 3.0
T: USB1
B: USB2
5
RoHS
USB3_3_4
SATA3_1
16
6
1
SATA3_0
HD_AUDIO1
SATA3_3
7
1
PANEL1
SPK_CI1
1
BIOS
ROM
USB_4_5
HDLED RESET
PCIE1
PLED PWRBTN
1
H110M-DGS
8
TPMS1
9
Audio
CODEC
PCIE2
CLRMOS1
15
14
13
12 11 10
English
Center:
FRONT
Top:
LINE IN
Bottom:
MIC IN
1
CMOS
Battery
Intel
H110
SATA3_2
USB 2.0
T: USB2
B: USB3
5
No. Description
English
6
1
ATX 12V Power Connector (ATX12V1)
2
CPU Fan Connector (CPU_FAN1)
3
2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
4
Chassis Fan Connector (CHA_FAN1)
5
ATX Power Connector (ATXPWR1)
6
USB 3.0 Header (USB3_3_4)
7
SATA3 Connector (SATA3_0)
8
TPM Header (TPMS1)
9
USB 2.0 Header (USB_4_5)
10
Clear CMOS Pad (CLRMOS1)
11
System Panel Header (PANEL1)
12
Chassis Intrusion and Speaker Header (SPK_CI1)
13
SATA3 Connector (SATA3_1)
14
SATA3 Connector (SATA3_2)
15
SATA3 Connector (SATA3_3)
16
Front Panel Audio Header (HD_AUDIO1)
H110M-DGS
1.4 I/O Panel
3
2
1
4
10
9
6
7
8
5
No. Description
No. Description
1
PS/2 Mouse Port (Green)***
6
USB 2.0 Ports (USB23)***
2
LAN RJ-45 Port*
7
USB 2.0 Ports (USB01)
3
Line In (Light Blue)**
8
USB 3.0 Ports (USB3_12)
4
Front Speaker (Lime)**
9
DVI-D Port
5
Microphone (Pink)**
10
PS/2 Keyboard Port (Purple)***
* There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications
ACT/LINK LED
SPEED LED
Activity / Link LED
Speed LED
Status
Description
Status
Description
Off
Blinking
On
No Link
Data Activity
Link
Off
Orange
Green
10Mbps connection
100Mbps connection
1Gbps connection
English
LAN Port
7
** To configure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multichannel audio feature through the audio driver.
Please set Speaker Configuration to “7.1 Speaker”in the Realtek HD Audio Manager.
Function of the Audio Ports in 7.1-channel Configuration:
Port
Function
Light Blue (Rear panel)
Lime (Rear panel)
Pink (Rear panel)
Lime (Front panel)
Rear Speaker Out
Front Speaker Out
Central /Subwoofer Speaker Out
Side Speaker Out
*** Supports ACPI wake-up function
English
8
H110M-DGS
Chapter 2 Installation
This is a Micro ATX form factor motherboard. Before you install the motherboard,
study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
English
• Make sure to unplug the power cord before installing or removing the motherboard
components. Failure to do so may cause physical injuries and damages to motherboard
components.
• In order to avoid damage from static electricity to the motherboard’s components,
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or
in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not overtighten the screws! Doing so may damage the motherboard.
9
2.1 Installing the CPU
1. Before you insert the 1151-Pin CPU into the socket, please check if the PnP cap is on the
socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not
force to insert the CPU into the socket if above situation is found. Otherwise, the CPU
will be seriously damaged.
2. Unplug all power cables before installing the CPU.
1
A
B
2
English
10
H110M-DGS
4
3
English
5
11
Please save and replace the cover if the processor is removed. The cover must be placed if
you wish to return the motherboard for after service.
English
12
H110M-DGS
2.2 Installing the CPU Fan and Heatsink
U_
FA
N
2
English
CP
1
13
2.3 Installing Memory Modules (DIMM)
This motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.
1. For dual channel configuration, you always need to install identical (the same brand,
speed, size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Dual Channel Memory Technology with only one memory module
installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot;
otherwise, this motherboard and DIMM may be damaged..
The DIMM only fits in one correct orientation. It will cause permanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
English
14
H110M-DGS
1
2
English
3
15
2.4 Expansion Slots (PCI Express Slots)
There are 2 PCI Express slots on the motherboard.
Before installing an expansion card, please make sure that the power supply is switched off
or the power cord is unplugged. Please read the documentation of the expansion card and
make necessary hardware settings for the card before you start the installation.
PCIe slots:
PCIE1 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards
PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
English
16
H110M-DGS
2.5 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these
headers and connectors. Placing jumper caps over the headers and connectors will cause
permanent damage to the motherboard.
System Panel Header
(9-pin PANEL1)
(see p.5, No. 11)
GND
GND
RESET#
GND
PWRBTN#
HDLED-
PLEDPLED+
HDLED+
1
Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may configure the way to turn
off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart the
computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED is on when the
system is operating. The LED keeps blinking when the system is in S1/S3 sleep state. The
LED is off when the system is in S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED is on when the
hard drive is reading or writing data.
English
The front panel design may differ by chassis. A front panel module mainly consists of power
switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the
pin assignments are matched correctly.
17
USB 2.0 Header
(9-pin USB_4_5)
(see p.5, No. 9)
DUMMY
GND
DUMMY
SPEAKER
SATA3_0
DUMMY
SATA3_1
Serial ATA3 Connectors
(SATA3_0)
(see p.5, No. 7)
(SATA3_1)
(see p.5, No. 13)
(SATA3_2)
(see p.5, No. 14)
(SATA3_3)
(see p.5, No. 15)
SIGNAL
SATA3_2
(7-pin SPK_CI1)
(see p.5, No. 12)
+5V
1
SATA3_3
Chassis Intrusion and
Speaker Header
1
USB_PWR
USB_PWR
P-
P-
P+
P+
GND
GND
DUMMY
USB 3.0 Header
(19-pin USB3_3_4)
(see p.5, No. 6)
Vbus
Vbus
IntA_PB_SSRXIntA_PB_SSRX+
IntA_PA_SSRX-
GND
IntA_PA_SSRX+
IntA_PB_SSTX-
GND
IntA_PA_SSTX-
IntA_PB_SSTX+
IntA_PA_SSTX+
GND
IntA_PB_D-
GND
IntA_PA_D-
IntA_PB_D+
IntA_PA_D+
Dummy
1
English
18
Please connect the
chassis intrusion and the
chassis speaker to this
header.
These four SATA3
connectors support SATA
data cables for internal
storage devices with up to
6.0 Gb/s data transfer rate.
Besides four USB 2.0
ports on the I/O panel,
there is one header on this
motherboard. Each USB
2.0 header can support
two ports.
Besides two USB 3.0 ports
on the I/O panel, there
is one header on this
motherboard. Each USB
3.0 header can support
two ports.
H110M-DGS
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.5, No. 16)
OUT_RET
OUT2_L
J_SENSE
MIC_RET
OUT2_R
PRESENCE#
MIC2_R
GN D
This header is for
connecting audio devices
to the front audio panel.
MIC2_L
1
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis
manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by the
steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to connect
them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and
adjust “Recording Volume”.
CPU Fan Connector
(4-pin CPU_FAN1)
(see p.5, No. 2)
GND
FAN_VOLTAGE
CHA_FAN_SPEED
FAN_SPEED_CONTROL
FAN_VOLTAGE
CPU_FAN_SPEED
GND
FAN_SPEED_CONTROL
1
2
3
4
Please connect fan cables
to the fan connector and
match the black wire to
the ground pin.
This motherboard provides a 4-Pin CPU fan
(Quiet Fan) connector.
If you plan to connect a
3-Pin CPU fan, please
connect it to Pin 1-3.
English
Chassis Fan Connector
(4-pin CHA_FAN1)
(see p.5, No. 4)
19
ATX Power Connector
(24-pin ATXPWR1)
1
This motherboard provides a 24-pin ATX power
13
(see p.5, No. 5)
connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin
13.
12
ATX 12V Power
Connector
(8-pin ATX12V1)
(see p.5, No. 1)
TPM Header
(17-pin TPMS1)
(see p.5, No. 8)
24
5
1
8
4
1
PCICLK
FRAME
PCIRST#
GND
SMB_CLK_MAIN
SMB_DATA_MAIN
LAD3
LAD2
+3V
LAD1
LAD0
GND
S_PWRDWN#
+3VSB
GND
Clear CMOS Pad
(CLRMOS1)
(see p.5, No. 10)
English
20
SERIRQ#
GND
This motherboard provides a 8-pin ATX 12V
power connector.
This connector supports Trusted
Platform Module (TPM) system,
which can securely store keys,
digital certificates, passwords,
and data. A TPM system also
helps enhance network security,
protects digital identities, and
ensures platform integrity.
CLRMOS1 allows you to
clear the data in CMOS. To
clear CMOS, take out the
CMOS battery and short the
Clear CMOS Pad.
H110M-DGS
Chapter 3 Software and Utilities Operation
3.1 Installing Drivers
The Support CD that comes with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard’s features.
Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu does not appear automatically, locate and double click on the file
“ASRSETUP.EXE” in the Support CD to display the menu.
Drivers Menu
The drivers compatible to your system will be auto-detected and listed on the
support CD driver page. Please click Install All or follow the order from top to
bottom to install those required drivers. Therefore, the drivers you install can work
properly.
Utilities Menu
The Utilities Menu shows the application software that the motherboard supports.
Click on a specific item then follow the installation wizard to install it.
English
To improve Windows 7 compatibility, please download and install the following hot fix
provided by Microsoft.
“KB2720599”: http://support.microsoft.com/kb/2720599/en-us
21
3.2 ASRock Live Update & APP Shop
The ASRock Live Update & APP Shop is an online store for purchasing and
downloading software applications for your ASRock computer. You can quickly and
easily install various apps and support utilities, such as USB Key, XFast LAN, XFast
RAM and more. With ASRock APP Shop, you can optimize your system and keep
your motherboard up to date simply with a few clicks.
Double-click
utility.
on your desktop to access ASRock Live Update & APP Shop
*You need to be connected to the Internet to download apps from the ASRock Live Update & APP Shop.
3.2.1 UI Overview
Category Panel
Hot News
Information Panel
Category Panel: The category panel contains several category tabs or buttons that
when selected the information panel below displays the relative information.
Information Panel: The information panel in the center displays data about the
currently selected category and allows users to perform job-related tasks.
English
Hot News: The hot news section displays the various latest news. Click on the image
to visit the website of the selected news and know more.
22
H110M-DGS
3.2.2 Apps
When the "Apps" tab is selected, you will see all the available apps on screen for you
to download.
Installing an App
Step 1
Find the app you want to install.
The most recommended app appears on the left side of the screen. The other various
apps are shown on the right. Please scroll up and down to see more apps listed.
You can check the price of the app and whether you have already intalled it or not.
- The red icon displays the price or "Free" if the app is free of charge.
- The green "Installed" icon means the app is installed on your computer.
Step 2
English
Click on the app icon to see more details about the selected app.
23
Step 3
If you want to install the app, click on the red icon
to start downloading.
Step 4
When installation completes, you can fi nd the green "Installed" icon appears on the
upper right corner.
English
To uninstall it, simply click on the trash can icon
*The trash icon may not appear for certain apps.
24
.
H110M-DGS
Upgrading an App
You can only upgrade the apps you have already installed. When there is an
available new version for your app, you will fi nd the mark of "New Version"
appears below the installed app icon.
Step 1
Click on the app icon to see more details.
Step 2
to start upgrading.
English
Click on the yellow icon
25
3.2.3 BIOS & Drivers
Installing BIOS or Drivers
When the "BIOS & Drivers" tab is selected, you will see a list of recommended or
critical updates for the BIOS or drivers. Please update them all soon.
Step 1
Please check the item information before update. Click on
Step 2
Click to select one or more items you want to update.
Step 3
Click Update to start the update process.
English
26
to see more details.
H110M-DGS
3.2.4 Setting
English
In the "Setting" page, you can change the language, select the server location, and
determine if you want to automatically run the ASRock Live Update & APP Shop
on Windows startup.
27
3.3 Enabling USB Ports for Windows® 7 Installation
Intel® Braswell and Skylake has removed their support for the Enhanced Host
Controller Interface (EHCI – USB2.0) and only kept the eXtensible Host Controller
Interface (XHCI – USB3.0). Due to that fact that XHCI is not included in the
Windows 7 inbox drivers, users may find it difficult to install Windows 7 operating
system because the USB ports on their motherboard won’t work. In order for the
USB ports to function properly, please create a Windows® 7 installation disk with
the Intel® USB 3.0 eXtensible Host Controller (xHCI) drivers packed into the ISO
file.
Requirements
•
•
•
•
A Windows® 7 installation disk or USB drive
USB 3.0 drivers (included in the ASRock Support CD or website)
A Windows® PC
Win7 USB Patcher (included in the ASRock Support CD or website)
Scenarios
You have an ODD and PS/2 ports:
If there is an optical disc drive, PS/2 ports and PS/2 Keyboard or mouse on your computer,
you can skip the instructions below and go ahead to install Windows® 7 OS.
You only have an ODD (For Intel Skylake platforms only):
If there is an optical disc drive but no PS/2 ports on your computer, please enable the “PS/2
Simulator” option in UEFI SETUP UTILITY > Advanced > USB Configuration, which
allows the USB port to function as a PS/2 port, and then you can install the Windows® 7
OS. Please set PS/2 Simulator back to disabled after the installation.
You’ve got nothing:
If you do not have an optical disc drive, please find another computer and follow the
instructions below to create a new ISO file with the “Win7 USB Patcher”. Then use the new
patched Windows® 7 installation USB drive to install Windows® 7 OS.
English
28
H110M-DGS
Instructions
Step 1
Insert the Windows® 7 installation disk or USB drive to your system.
Step 2
Extract the tool (Win7 USB Patcher) and launch it.
Step 3
Select the “Win7 Folder” from Step1 by clicking the red circle as shown as the picture
below.
Step 4
English
Select the “USB Driver Folder” by clicking the red circle as shown as the picture below.
If you are using ASRock’s Support CD for the USB 3.0 driver, please select your CD-ROM.
29
Step 5
Select where to save the ISO file by pressing the red circle as shown as the picture below.
Step 6
If you want to burn the patched image to a CD, please check “Burn Image” and select “Target
Device to Burn”. If not, the patched ISO image will be exported to the destination selected
in Step5. Then Press “Start” to proceed.
Step 7
Now you are able to install Windows® 7 on Braswell or Skylake with the new burned CD.
Or please use the patched ISO image to make an OS USB drive to install the OS.
English
30
H110M-DGS
Chapter 4 UEFI SETUP UTILITY
4.1 Introduction
This section explains how to use the UEFI SETUP UTILITY to configure your
system. You may run the UEFI SETUP UTILITY by pressing <F2> or <Del> right
after you power on the computer, otherwise, the Power-On-Self-Test (POST) will
continue with its test routines. If you wish to enter the UEFI SETUP UTILITY after
POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the
reset button on the system chassis. You may also restart by turning the system off
and then back on.
English
Because the UEFI software is constantly being updated, the following UEFI setup screens
and descriptions are for reference purpose only, and they may not exactly match what you
see on your screen.
31
4.2 EZ Mode
The EZ Mode screen appears when you enter the BIOS setup program by default. EZ
mode is a dashboard which contains multiple readings of the system’s current status.
You can check the most crucial information of your system, such as CPU speed,
DRAM frequency, SATA information, fan speed, etc.
Press <F6> or click the "Advanced Mode" button at the upper right corner of the
screen to switch to "Advanced Mode" for more options.
No.
English
32
Function
1
Help
2
Load UEFI Defaults
3
Save Changes and Exit
4
Discard Changes
5
Change Language
6
Switch to Advanced Mode
H110M-DGS
4.3 Advanced Mode
The Advanced Mode provides more options to configure the BIOS settings. Refer to
the following sections for the detailed configurations.
To access the EZ Mode, press <F6> or click the "EZ Mode" button at the upper right
corner of the screen.
4.3.1 UEFI Menu Bar
Main
For setting system time/date information
OC Tweaker
For overclocking configurations
Advanced
For advanced system configurations
Tool
Useful tools
H/W Monitor
Displays current hardware status
Boot
For configuring boot settings and boot priority
Security
For security settings
Exit
Exit the current screen or the UEFI Setup Utility
English
The top of the screen has a menu bar with the following selections:
33
4.3.2 Navigation Keys
Use < > key or < > key to choose among the selections on the menu bar, and
use < > key or < > key to move the cursor up or down to select items, then
press <Enter> to get into the sub screen. You can also use the mouse to click your
required item.
Please check the following table for the descriptions of each navigation key.
Navigation Key(s)
+ / -
To change option for the selected items
<Tab>
Switch to next function
<PGUP>
Go to the previous page
<PGDN>
Go to the next page
<HOME>
Go to the top of the screen
<END>
English
34
Description
Go to the bottom of the screen
<F1>
To display the General Help Screen
<F5>
Add / Remove Favorite
<F7>
Discard changes and exit the SETUP UTILITY
<F9>
Load optimal default values for all the settings
<F10>
Save changes and exit the SETUP UTILITY
<F12>
Print screen
<ESC>
Jump to the Exit Screen or exit the current screen
H110M-DGS
4.4 Main Screen
When you enter the UEFI SETUP UTILITY, the Main screen will appear and
display the system overview.
Favorite
English
Display your collection of BIOS items. Press F5 to add/remove your favorite items.
35
4.5 OC Tweaker Screen
In the OC Tweaker screen, you can set up overclocking features.
Because the UEFI software is constantly being updated, the following UEFI setup screens
and descriptions are for reference purpose only, and they may not exactly match what you
see on your screen.
CPU Configuration
Intel SpeedStep Technology
Intel SpeedStep technology allows processors to switch between multiple frequencies and voltage points for better power saving and heat dissipation.
Intel Turbo Boost Technology
Intel Turbo Boost Technology enables the processor to run above its base operating
frequency when the operating system requests the highest performance state.
Long Duration Power Limit
English
Configure Package Power Limit 1 in watts. When the limit is exceeded, the CPU
ratio will be lowered after a period of time. A lower limit can protect the CPU and
save power, while a higher limit may improve performance.
36
H110M-DGS
Long Duration Maintained
Configure the period of time until the CPU ratio is lowered when the Long
Duration Power Limit is exceeded.
Short Duration Power Limit
Configure Package Power Limit 2 in watts. When the limit is exceeded, the CPU
ratio will be lowered immediately. A lower limit can protect the CPU and save
power, while a higher limit may improve performance.
DRAM Configuration
DRAM Timing Configuration
Load XMP Setting
Load XMP settings to overclock the DDR4 memory and perform beyond standard
specifications.
DRAM Reference Clock
Select Auto for optimized settings.
DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s) inserted
and assign the appropriate frequency automatically.
Primary Timing
CAS# Latency (tCL)
The time between sending a column address to the memory and the beginning of the data
in response.
RAS# to CAS# Delay and Row Precharge (tRCDtRP) O
RAS# to CAS# Delay : The number of clock cycles required between the opening of
a row of memory and accessing columns within it.
Row Precharge: The number of clock cycles required between the issuing of the
precharge command and opening the next row.
English
RAS# Active Time (tRAS)
The number of clock cycles required between a bank active command and issuing the
precharge command.
37
Command Rate (CR)
The delay between when a memory chip is selected and when the first active command can
be issued.
Secondary Timing
Write Recovery Time (tWR)
The amount of delay that must elapse after the completion of a valid write operation,
before an active bank can be precharged.
Refresh Cycle Time (tRFC)
The number of clocks from a Refresh command until the first Activate command to
the same rank.
RAS to RAS Delay (tRRD)
The number of clocks between two rows activated in different banks of the same
rank.
Write to Read Delay (tWTR)
The number of clocks between the last valid write operation and the next read command to
the same internal bank.
Read to Precharge (tRTP)
The number of clocks that are inserted between a read command to a row precharge command to the same rank.
Four Activate Window (tFAW)
The time window in which four activates are allowed the same rank.
CAS Write Latency (tCWL)
Configure CAS Write Latency.
Third Timing
tREFI
Configure refresh cycles at an average periodic interval.
English
tCKE
Configure the period of time the DDR4 initiates a minimum of one refresh
command internally once it enters Self-Refresh mode.
38
H110M-DGS
tRDRD_sg
Configure between module read to read delay.
tRDRD_dg
Configure between module read to read delay.
tRDRD_dr
Configure between module read to read delay.
tRDRD_dd
Configure between module read to read delay.
tRDWR_sg
Configure between module read to write delay.
tRDWR_dg
Configure between module read to write delay.
tRDWR_dr
Configure between module read to write delay.
tRDWR_dd
Configure between module read to write delay.
tWRRD_sg
Configure between module write to read delay.
tWRRD_dg
Configure between module write to read delay.
tWRRD_dr
Configure between module write to read delay.
tWRRD_dd
Configure between module write to read delay.
English
tWRWR_sg
Configure between module write to write delay.
39
tWRWR_dg
Configure between module write to write delay.
tWRWR_dr
Configure between module write to write delay.
tWRWR_dd
Configure between module write to write delay.
RTL Init Value
Configure round trip latency init value for round trip latency training.
IO-L Init Value
Configure IO latency init value for IO latency traning.
RTL (CH A)
Configure round trip latency for channel A.
RTL (CH B)
Configure round trip latency for channel B.
IO-L (CH A)
Configure IO latency for channel A.
IO-L (CH B)
Configure IO latency for channel B.
IO-L Offset (CH A)
Configure IO latency offset for channel A.
IO-L Offset (CH B)
Configure IO latency offset for channel B.
RFR Delay (CH A)
Configure RFR Delay for Channel A.
English
RFR Delay (CH B)
Configure RFR Delay for Channel B.
40
H110M-DGS
Fourth Timing
twRPRE
Configure twRPRE.
Write_Early_ODT
Configure Write_Early_ODT.
tAONPD
Configure tAONPD.
tXP
Configure tXP.
tXPDLL
Configure tXPDLL.
tPRPDEN
Configure tPRPDEN.
tRDPDEN
Configure tRDPDEN.
twRPDEN
Configure twRPDEN.
OREF_RI
Configure OREF_RI.
tREFIx9
Configure tREFIx9.
txSDLL
Configure txSDLL.
txs_offset
English
Configure txs_offset.
tZQOPER
Configure tZQOPER.
41
tMOD
Configure tMOD.
ZQCS_period
Configure ZQCS_period.
tZQCS
Configure tZQCS.
Advanced Setting
ODT WR (CH A)
Configure the memory on die termination resistors' WR for channel A.
ODT WR (CH B)
Configure the memory on die termination resistors' WR for channel B.
ODT PARK (CH A)
Configure the memory on die termination resistors' PARK for channel A.
ODT PARK (CH B)
Configure the memory on die termination resistors' PARK for channel B.
ODT NOM (CH A)
Use this to change ODT (CH A) Auto/Manual settings. The default is [Auto].
ODT NOM (CH B)
Use this to change ODT (CH B) Auto/Manual settings. The default is [Auto].
MRC Fast Boot
Enable Memory Fast Boot to skip DRAM memory training for booting faster.
Dll Bandwidth 0
Configure the Dll Bandwidth 0.
Dll Bandwidth 1
English
Configure the Dll Bandwidth 1.
Dll Bandwidth 2
Configure the Dll Bandwidth 2.
42
H110M-DGS
Dll Bandwidth 3
Configure the Dll Bandwidth 3.
Margin Limit
Adjust Margin Limit to get better memory margin.
Voltage Configuration
DRAM Voltage
Use this to configure DRAM Voltage. The default value is [Auto].
PCH Voltage
Configure the chipset voltage (1.0V).
Save User Default
Type a profile name and press enter to save your settings as user default.
Load User Default
Load previously saved user defaults.
Save User UEFI Setup Profile to Disk
Save current UEFI settings as an user default profile to disk.
Load User UEFI Setup Profile from Disk
English
Load previously saved user defaults from the disk.
43
4.6 Advanced Screen
In this section, you may set the configurations for the following items: CPU
Configuration, Chipset Configuration, Storage Configuration, ACPI Configuration,
USB Configuration and Trusted Computing.
Setting wrong values in this section may cause the system to malfunction.
UEFI Configuration
UEFI Setup Style
Select the default mode when entering the UEFI setup utility.
Active Page on Entry
Select the default page when entering the UEFI setup utility.
English
44
H110M-DGS
4.6.1 CPU Configuration
Intel Hyper Threading Technology
Intel Hyper Threading Technology allows multiple threads to run on each core, so
that the overall performance on threaded software is improved.
Active Processor Cores
Select the number of cores to enable in each processor package.
CPU C States Support
Enable CPU C States Support for power saving. It is recommended to keep C3, C6
and C7 all enabled for better power saving.
Enhanced Halt State (C1E)
Enable Enhanced Halt State (C1E) for lower power consumption.
CPU C3 State Support
Enable C3 sleep state for lower power consumption.
English
CPU C6 State Support
Enable C6 deep sleep state for lower power consumption.
CPU C7 State Support
Enable C7 deep sleep state for lower power consumption.
45
Package C State Support
Enable CPU, PCIe, Memory, Graphics C State Support for power saving.
CPU Thermal Throttling
Enable CPU internal thermal control mechanisms to keep the CPU from overheating.
No-Execute Memory Protection
Processors with No-Execution Memory Protection Technology may prevent certain
classes of malicious buffer overflow attacks.
Intel Virtualization Technology
Intel Virtualization Technology allows a platform to run multiple operating systems
and applications in independent partitions, so that one computer system can
function as multiple virtual systems.
Hardware Prefetcher
Automatically prefetch data and code for the processor. Enable for better
performance.
Adjacent Cache Line Prefetch
Automatically prefetch the subsequent cache line while retrieving the currently
requested cache line. Enable for better performance.
English
46
H110M-DGS
4.6.2 Chipset Configuration
Primary Graphics Adapter
Select a primary VGA.
Top of Lower USB Dram
Maximum Value of TOLUD. Dynamic assignment would adjust TOLUD
automatically based on largest MMIO length of installed graphic controller.
VT-d
Intel® Virtualization Technology for Directed I/O helps your virtual machine
monitor better utilize hardware by improving application compatibility and
reliability, and providing additional levels of manageability, security, isolation, and
I/O performance.
PCIE2 Link Speed
Select the link speed for PCIE2.
PCIE ASPM Support
English
This option enables/disables the ASPM support for all CPU downstream devices.
PCH PCIE ASPM Support
This option enables/disables the ASPM support for all PCH PCIE devices.
47
DMI ASPM Support
This option enables/disables the control of ASPM on CPU side of the DMI Link.
PCH DMI ASPM Support
This option enables/disables the ASPM support for all PCH DMI devices.
Share Memory
Configure the size of memory that is allocated to the integrated graphics processor when
the system boots up.
IGPU Multi-Monitor
Select disable to disable the integrated graphics when an external graphics card is installed.
Select enable to keep the integrated graphics enabled at all times.
Onboard LAN
Enable or disable the onboard network interface controller.
Onboard HD Audio
Enable/disable onboard HD audio. Set to Auto to enable onboard HD audio and
automatically disable it when a sound card is installed.
Front Panel
Enable/disable front panel HD audio.
Restore on AC/Power Loss
Select the power state after a power failure. If [Power Off] is selected, the power will
remain off when the power recovers. If [Power On] is selected, the system will start
to boot up when the power recovers.
English
48
H110M-DGS
4.6.3 Storage Configuration
SATA Controller(s)
Enable/disable the SATA controllers.
SATA Aggressive Link Power Management
SATA Aggressive Link Power Management allows SATA devices to enter a low
power state during periods of inactivity to save power. It is only supported by AHCI
mode.
Hard Disk S.M.A.R.T.
English
S.M.A.R.T stands for Self-Monitoring, Analysis, and Reporting Technology. It is a
monitoring system for computer hard disk drives to detect and report on various
indicators of reliability.
49
4.6.4 ACPI Configuration
Suspend to RAM
Select disable for ACPI suspend type S1. It is recommended to select auto for ACPI
S3 power saving.
ACPI HEPT Table
Enable the High Precision Event Timer for better performance.
PS/2 Keyboard Power On
Allow the system to be waked up by a PS/2 Keyboard.
PCIE Devices Power On
Allow the system to be waked up by a PCIE device and enable wake on LAN.
RTC Alarm Power On
Allow the system to be waked up by the real time clock alarm. Set it to By OS to let
it be handled by your operating system.
English
USB Keyboard/Remote Power On
Allow the system to be waked up by an USB keyboard or remote controller.
50
H110M-DGS
USB Mouse Power On
English
Allow the system to be waked up by an USB mouse.
51
4.6.5 USB Configuration
Legacy USB Support
Enable or disable Legacy OS Support for USB 2.0 devices. If you encounter USB
compatibility issues it is recommended to disable legacy USB support. Select UEFI
Setup Only to support USB devices under the UEFI setup and Windows/Linux
operating systems only.
PS/2 Stimulator
Enable PS/2 Stimulator. This should be enabled for the complete USB keyboard
legacy support for non-USB aware OSes.
*Enable this option if you install Windows 7.
English
52
H110M-DGS
4.6.6 Trusted Computing
Security Device Support
English
Enable or disable BIOS support for security device.
53
4.7 Tools
OMG (Online Management Guard)
Administrators are able to establish an internet curfew or restrict internet access
at specified times via OMG. You may schedule the starting and ending hours of
internet access granted to other users. In order to prevent users from bypassing
OMG, guest accounts without permission to modify the system time are required.
UEFI Tech Service
Contact ASRock Tech Service if you are having trouble with your PC. Please setup
network configuration before using UEFI Tech Service.
Easy Driver Installer
For users that don’t have an optical disk drive to install the drivers from our support
CD, Easy Driver Installer is a handy tool in the UEFI that installs the LAN driver
to your system via an USB storage device, then downloads and installs the other
required drivers automatically.
Boot Manager
English
Boot Manager is specifically designed for the dual OS platform/multi-OS platform
users to easily customize and manage the boot menu.
*Please connect more than one boot devices to use this tool.
54
H110M-DGS
Boot Manager
Enable/disable the Boot Manager.
Boot Manager Timeout
Enable/disable the Boot Manager Timeout.
Timeout Seconds
Configure the number of seconds to wait for the Boot Manager.
Instant Flash
Save UEFI files in your USB storage device and run Instant Flash to update your
UEFI.
Internet Flash - DHCP (Auto IP), Auto
English
ASRock Internet Flash downloads and updates the latest UEFI firmware version
from our servers for you. Please setup network configuration before using Internet
Flash.
*For BIOS backup and recovery purpose, it is recommended to plug in your USB
pen drive before using this function.
55
Network Configuration
Use this to configure internet connection settings for Internet Flash.
Internet Setting
Enable or disable sound effects in the setup utility.
UEFI Download Server
Select a server to download the UEFI firmware.
English
56
H110M-DGS
4.8 Hardware Health Event Monitoring Screen
This section allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, fan
speed and voltage.
Fan-Tastic Tuning
Select a fan mode for CPU Fans, or choose Customize to set 5 CPU temperatures and
assign a respective fan speed for each temperature.
CPU Fan 1 Setting
Select a fan mode for CPU Fan, or choose Customize to set 5 CPU temperatures
and assign a respective fan speed for each temperature.
Chassis Fan 1 Setting
Select a fan mode for Chassis Fan, or choose Customize to set 5 CPU temperatures
and assign a respective fan speed for each temperature.
Chassis Fan 1 Temp Source
Select a fan temperature source for Chassis Fan.
English
Over Temperature Protection
When Over Temperature Protection is enabled, the system automatically shuts
down when the motherboard is overheated.
57
Case Open Feature
Enable or disable Case Open Feature to detect whether the chassis cover has been
removed.
English
58
H110M-DGS
4.9 Security Screen
In this section you may set or change the supervisor/user password for the system.
You may also clear the user password.
Supervisor Password
Set or change the password for the administrator account. Only the administrator
has authority to change the settings in the UEFI Setup Utility. Leave it blank and
press enter to remove the password.
User Password
Set or change the password for the user account. Users are unable to change the
settings in the UEFI Setup Utility. Leave it blank and press enter to remove the
password.
Secure Boot
Use this item to enable or disable support for Windows 8.1 Secure Boot.
Intel(R) Platform Trust Technology
English
Enable/disable Intel PTT in ME. Disable this option to use discrete TPM Module.
59
4.10 Boot Screen
This section displays the available devices on your system for you to configure the
boot settings and the boot priority.
Fast Boot
Fast Boot minimizes your computer's boot time. In fast mode you may not boot
from an USB storage device. Ultra Fast mode is only supported by Windows 8.1
and the VBIOS must support UEFI GOP if you are using an external graphics card.
Please notice that Ultra Fast mode will boot so fast that the only way to enter this
UEFI Setup Utility is to Clear CMOS or run the Restart to UEFI utility in Windows.
Boot From Onboard LAN
Allow the system to be waked up by the onboard LAN.
Setup Prompt Timeout
Configure the number of seconds to wait for the setup hot key.
Bootup Num-Lock
Select whether Num Lock should be turned on or off when the system boots up.
English
Boot Beep
Select whether the Boot Beep should be turned on or off when the system boots up. Please
note that a buzzer is needed.
60
H110M-DGS
Full Screen Logo
Enable to display the boot logo or disable to show normal POST messages.
AddOn ROM Display
Enable AddOn ROM Display to see the AddOn ROM messages or configure the
AddOn ROM if you've enabled Full Screen Logo. Disable for faster boot speed.
Boot Failure Guard
If the computer fails to boot for a number of times the system automatically restores
the default settings.
Boot Failure Guard Count
English
Configure the number of attempts to boot until the system automatically restores
the default settings.
61
CSM (Compatibility Support Module)
CSM
Enable to launch the Compatibility Support Module. Please do not disable unless
you’re running a WHCK test. If you are using Windows 8.1 64-bit and all of your
devices support UEFI, you may also disable CSM for faster boot speed.
Launch PXE OpROM Policy
Select UEFI only to run those that support UEFI option ROM only. Select Legacy
only to run those that support legacy option ROM only. Select Do not launch to not
execute both legacy and UEFI option ROM.
Launch Storage OpROM Policy
Select UEFI only to run those that support UEFI option ROM only. Select Legacy
only to run those that support legacy option ROM only. Select Do not launch to not
execute both legacy and UEFI option ROM.
Launch Video OpROM Policy
English
Select UEFI only to run those that support UEFI option ROM only. Select Legacy
only to run those that support legacy option ROM only. Select Do not launch to not
execute both legacy and UEFI option ROM.
62
H110M-DGS
4.11 Exit Screen
Save Changes and Exit
When you select this option the following message, “Save configuration changes
and exit setup?” will pop out. Select [OK] to save changes and exit the UEFI SETUP
UTILITY.
Discard Changes and Exit
When you select this option the following message, “Discard changes and exit
setup?” will pop out. Select [OK] to exit the UEFI SETUP UTILITY without saving
any changes.
Discard Changes
When you select this option the following message, “Discard changes?” will pop
out. Select [OK] to discard all changes.
Load UEFI Defaults
Load UEFI default values for all options. The F9 key can be used for this operation.
Launch EFI Shell from filesystem device
English
Copy shellx64.efi to the root directory to launch EFI Shell.
63
Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer
for further information. For technical questions, please submit a support request
form at http://www.asrock.com/support/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)
ASRock EUROPE B.V.
Bijsterhuizen 11-11
6546 AR Nijmegen
The Netherlands
Phone: +31-24-345-44-33
Fax: +31-24-345-44-38
ASRock America, Inc.
13848 Magnolia Ave, Chino, CA91710
U.S.A.
Phone: +1-909-590-8308
Fax: +1-909-590-1026
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement