Descargar AVX
Connecting the Units
<ENGLISH>
When Connecting the Multi-Channel AV Master Unit
• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same
colors correctly.
• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connected
to a terminal coupled with ignition switch ON/OFF
operations. If this is not done, the vehicle battery
may be drained when you are away from the vehicle for several hours. (Fig.1)
O
Green
O
Multi-CD player
(sold separately)
STAR
STAR
T
ACC position
F
OF
OF
ACC
Multi-Channel AV
Master Unit (e.g. AVM-P9000)
(sold separately)
N
F
N
This product conforms to new cord colors.
• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery
voltage.
• To avoid shorts in the electrical system, be sure to
disconnect the ≠ battery cable before beginning
installation.
• Refer to the owner’s manual for details on
connecting the power amp and other units, then
make connections correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get
hot, such as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.
• Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.
• If the RCA pin jack on the unit will not be used, do
not remove the caps attached to the end of the connector.
T
AVX-P7300DVD
INSTALLATION MANUAL
INSTALLATION MANUAL
Note:
No ACC position
Fig. 1
Yellow
Blue
Blue
• Cords for this product and those for other products
may be different colors even if they have the same
function. When connecting this product to another
product, refer to the supplied Installation manuals
of both products and connect cords that have the
same function.
Optical cable
(supplied with the MultiChannel AV Master Unit)
IP-BUS cable
(supplied with the TV tuner)
Black
Blue
This product
Blue
40 cm
FM MODULATOR
IP-BUS MAIN UNIT
IP-BUS AV MASTER
Hide-away TV Tuner
(e.g. GEX-P7000TV)
(sold separately)
Black
RCA cable (supplied)
6m
40 cm
RCA cable
(sold separately)
Green
Red
20 pin cable
(supplied with the TV tuner)
Gray
AV cable
(supplied with the
Multi-Channel AV
Master Unit)
IP-BUS cable (supplied with the
Multi-Channel AV Master Unit)
Gray
16 cm
Yellow
(AVM OUTPUT)
Blue
Green
Not used.
3m
20 pin cable
(supplied)
Red
Printed in Japan
<CRB1740-A> ES/RD
<KNKZF/01D00000>
Fig. 2
Connecting the Units
<ENGLISH>
When Using a Display Connected Rear Video Output
When Connecting the Head Unit
Connecting the Power Cord
This product’s rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.
Connection method
WARNING
• NEVER install the display in a location that enables the Driver to watch the DVD or
Video CD while Driving.
1. Clamp the parking brake
switch power supply side
lead.
This Product
Multi-CD player
(sold separately)
This product
2. Clamp firmly with
needle-nosed pliers.
Note:
Yellow (REAR
VIDEO OUTPUT)
Blue
• The position of the parking brake switch depends
on the vehicle model. For details, consult the
vehicle Owner’s Manual or dealer.
16 cm
This product
16 cm
16 cm
White (audio output (Left))
(REAR OUTPUT)
16 cm
Red (audio output (Right))
(REAR OUTPUT)
16 cm
Yellow (rear video output)
(REAR VIDEO OUTPUT)
16 cm
Yellow (AVM output)
(AVM OUTPUT)
16 cm
Yellow (video input)
(VIDEO INPUT)
16 cm
Light green
Used to detect the ON/OFF status of the parking brake.
This lead must be connected to the power supply side
of the parking brake switch.
White (audio output (Left))
Red (audio output (Right))
Not used.
40 cm
RCA cable (supplied)
RCA cable (sold separately)
40 cm
Power supply side
Parking brake switch
Ground side
6m
Blue
Head Unit
(sold separately)
To video input
Fuse resistor
Yellow
To terminal always supplied with power
regardless of ignition switch position.
Fuse holder
To audio inputs
Display with RCA
input jacks
Fig. 3
Red
To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.
Black (ground)
To vehicle (metal) body.
Fig. 4
Fig. 5
Installation
<ENGLISH>
Note:
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver’s
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• Do not place the display in a position where it will
impede the driver’s visibility or affect the operation of your vehicle’s air bags.
• The semiconductor laser will be damaged if it
overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.
• If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 6)
7 When the installation space is not very deep
2. Install side brackets. (Fig. 8)
DIN Front/Rear-mount
When installing in a shallow space, secure with side brackets (small). In this case, stick
conceal tape on parts that protrude from the dashboard.
This unit can be properly installed either from “Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.
Holder
After inserting the holder into the dashboard, then select the appropriate tabs
according to the thickness of the dashboard material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
DIN Front-mount
Side bracket
30°
Dashboard
Installation with the rubber bush
Flush surface screw (5 × 6 mm)
1. Remove the frame. (Fig. 7)
182
53
Fig. 6
Rubber bush
Screw
Fig. 8
Frame
Conceal tape
3. Fastening the unit. (Fig. 9)
As a rule, secure with side brackets (large).
Pull out to remove the frame.
(When reattaching the frame, point the
side with a groove downwards and
attach it.)
Attach screw
Holder
After inserting the holder into the dashboard, then select the appropriate tabs
according to the thickness of the dashboard material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
Dashboard
Fig. 7
182
53
Side bracket
(small)
Fig. 10
Rubber bush
Screw
Attach screw
Side bracket
(large)
Fig. 9
Installation
<ENGLISH>
DIN Rear-mount
2. Fastening the unit to the factory radio mounting bracket.
(Fig. 12) (Fig. 13)
Installation using the screw holes on the side of the unit
Select a position where the screw holes of the bracket and the screw holes of this product
become aligned (are fitted), and tighten the screws at 2 places on each side. Use any of
binding screws (4 × 3 mm), binding screws (5 × 6 mm) or flush surface screws (5 × 6
mm), depending on the shape of the screw holes in the bracket.
1. Remove the frame. (Fig. 11)
*1 Use binding screws (4 × 3 mm) only.
Frame
*1
*1
Pull out to remove the frame.
(When reattaching the frame, point the
side with a groove downwards and
attach it.)
Fig. 11
Fig. 12
11
Screw
Dashboard
or Console
13
Factory radio mounting bracket
12
Fig. 13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement