C a t a l o g u e 2014-15

C a t a l o g u e 2014-15
SignalLED Studio Illuminated Signs
2014-15
Catalogue
Studio Illuminated Signs
The SignalLED range of illuminated RGB LED signs are a range of signs designed for use
outside recording studios, on-air & production studios, meeting rooms, conference rooms
and for fixed installations. The sign itself contains the control electronics, and RGB LEDs are
used, so the signs can be simply configured onsite for your particular requirements.
SignalLED Range of LED Signs
252
Custom Signs
254
Sonifex SignalLED Sign.
Photo courtesy of ABC Erina & OnAir Solutions.
251
Studio Illuminated Signs
SignalLED Range of LED Signs
Category: SignalLED Illuminated Signs.
Product Function: Signage for outside
studio/office doors and on studio walls
to indicate Mic Live, Recording, etc
Typical Applications: MIC LIVE, ON-AIR,
PHONE and RECORD signs for radio/TV
studios, TX-REH for production galleries,
MEETING IN PROGRESS for board rooms,
SILENCE PLEASE outside lecture theatres.
The SignalLED range of illuminated
RGB LED signs are a new range of signs
designed for use outside recording studios,
on-air & production studios, meeting
rooms, conference rooms and for fixed
installations. The sign itself contains the
control electronics, and RGB LEDs are
used, so the signs can be simply configured
onsite for your particular requirements.
Features:
• Low power consumption, only 4W.
• Maintenance free, LED lighting.
• Multi-coloured RGB LEDs offering 9
different colours.
• Sign can be made to flash, pulse, fade and
be on or off.
• Flush-mounting as standard or end/
ceiling-mounting with kits.
• 20cm (8”) or 40cm (16”) widths or 2 x
20cm (2 x 8”).
• Standard wording includes: MIC LIVE, ON
AIR, RECORD, PHONE, TRAFFIC FLAG ON,
AD BREAK, TX, REH, REHEARSAL, DOOR,
Different Display Modes
Five modes of illumination are available:
•
•
•
•
•
Constant illumination.
Flashing, regularly on/off.
Pulsing - flashing, then off, repeated
Fading
Off
•
•
•
•
•
OBIT, NO ENTRY, EXIT, SILENCE PLEASE,
MEETING IN PROGRESS, INTERVIEW IN
PROGRESS.
Custom signs can be etched with
company logos, different wording or
graphics.
2 x GPIs for control from a light switch,
or fader GPO (pull down to 0V).
Supplied as standard as red/green
switching.
Use separate remote control (LD-RPC)
to program the colour, switching mode
or brightness.
Supplied complete with fixings & DC
power supply.
RGB LEDs - Any Colours Possible
The illuminating LEDs in the unit are RGB
meaning that the colour of the sign can be
selected on installation.
You can configure the sign from one of 9
colours: white, green, red, blue, brick red,
yellow, orange, cyan and magenta.
9 different colours of the SignalLED Sign.
252
Studio Illuminated Signs
Single or Twin Signs
Each sign is 40cm or 20cm long. The 40cm
signs can be split into two 20cm sides which
can be separately, or jointly controlled, e.g.
you can have a 40cm ‘ON AIR’ sign, or twin
2 x 20cm signs, such as ‘ON AIR’ and ‘MIC
LIVE’.
Single 20cm Flush Mounting Sign
These are the available choices for the
smaller 20cm flush-mounting signs. Custom
signs can be made to order, if required.
LD-20F1REC Single Flush Mounting 20cm
‘RECORD’ Sign.
LD-40F1ONA Single Flush Mounting
40cm ‘ON AIR’ Sign.
LD-KC1 Ceiling Mounting Kit
The LD-KC1 mounting kit can be used to
attach a 40cm or 20cm flush mounting sign
to the ceiling or a desktop.
The LD-KC1 mounting kit used to attached the sign
to the ceiling.
Dual Control Inputs
The sign can be controlled by either, or both,
of 2 pull-low inputs, e.g. a single input can
be used to control a single ‘MIC LIVE’ sign,
or 2 inputs can be used to control a twin ‘TX’
and ‘REH’ sign with independent control of
each side of the sign.
7V-36V DC Input Option
For a small additional cost, the SignalLED
main circuit board can be modified to accept
a DC input in the range 7V-36V, for example,
if you have a 12V or 24V distributed DC
power network.
When placing your order, or requesting a
quotation, please either:
LD-20F1ONA Single Flush Mounting 20cm
‘ON AIR’ Sign.
LD-40F2ONA-MCL Twin ‘ON AIR’
& ‘MIC LIVE’ sign.
The LD-KC1 mounting kit used to attached the sign
to the desktop.
Change the ‘LD’ of the order code to ‘LDD’,
so for example, ‘LD-F1ONA’ becomes ‘LDDF1ONA’, or:
Add the item LD-DC to your order.
LD-20F1MCL Single Flush Mounting 20cm
‘MIC LIVE’ Sign.
The LD-KC1 mounting kit.
253
Studio Illuminated Signs
Flush or End Mounting
The sign is supplied as standard so that it
can be mounted flush to a wall, e.g. for the
‘TX’ & ‘REH’ sign shown below. However, a
mounting kit is available, LD-KE1, to mount
the sign perpendicular to a wall, e.g. above a
door, such as the ON AIR sign shown.
Simple Installation
The signs are supplied with a 6V DC power
supply. Simply wire up your control signal(s)
and DC input to the ‘screw terminal block’
inside the sign, route the cables through the
integral cable clamp and mount the unit on
the wall.
An installation tool, the LD-IT can be used
to hold the sign in place on the wall mount
whilst you wire it up.
LD-KE1 End Mounting Kit For 40cm Or 20cm Flush
Mounting Signs.
The display mode and colour options are
set-up using a separate remote control, the
LD-RPC.
End Mounting 40cm Single Sign (Created From
Single Flush Mounting LD-40F1ONA Sign & LD-KE1
kit).
LD-IT LED Sign End Mounting Installation Tool.
LD-40F2TX-REH Flush Mounting 40cm
Twin Sign.
LD-40F2ONA-SIL Twin ‘ON AIR’ & ‘SILENCE’ sign.
254
LD-RPC SignalLED Remote
Programming Controller
The SignalLED signs are preconfigured to
display certain colours when the control
inputs are active. Information on the colours
shown can be found on the Sonifex website.
To vary the colours and switching modes,
the LD-RPC Remote Programming Controller
must be used.
This allows a simple way of programming
any sign using a hand-held remote control.
Custom Signs
Although a range of standard signs is
supported, custom signs, for example
with your company name or logo, can be
produced for a nominal setup fee. Contact
Sonifex with your requirements.
Please note
that the
control is sold
separately and one
LP-RPC can program
multiple signs.
Examples Of Custom Signs
Custom Single Flush Mounting 40cm Sign.
Studio Illuminated Signs
Specification For SignalLED
Power Input:
5-7V DC
40cm Sign: 500mA max
Input Connector: 4 way screw terminal block
How to Order
Just select the name of the sign from the
list below.
LD-40F1TRF Single Flush Mounting 40cm ‘TRAFFIC
FLAG ON’ Sign.
LD-40F1NOE Single Flush Mounting 40cm
‘NO ENTRY’ Sign.
LD-40F1ONA Single Flush Mounting 40cm
‘ON AIR’ Sign.
Control Inputs:
2 x pull-down to 0V
Dimensions
(Perspex):
Small Single: 20cm (W) x 8cm (H)
Large Single: 40cm (W) x 8cm (H)
Dimensions
(Boxed 20cm):
40cm (W) x 20cm (D) x 11cm (H)
15.7” (W) x 7.9” (D) x 4.3” (H)
Dimensions
(Boxed 40cm):
60cm (W) x 20cm (D) x 11cm (H)
23.6” (W) x 7.9” (D) x 4.3” (H)
Weight (20cm):
Nett: 0.35kg Gross: 0.85kg
Nett: 0.8lb Gross: 1.9lb
Weight (40cm):
Nett: 0.55kg Gross: 1.15kg
Nett: 1.2lb Gross: 2.6lb
Equipment Type
Single Flush Mounting Signs (40cm):
LD-40F1REC
LD-40F1ADB Single Flush Mounting 40cm
‘AD BREAK’ Sign.
LD-40F1EXIT Single Flush Mounting 40cm
‘EXIT’ Sign.
LD-40F1MCL Single Flush Mounting 40cm
‘MIC LIVE’ Sign.
LD-40F1REH Single Flush Mounting 40cm
‘REHEARSAL’ Sign.
LD-40F1SIL Single Flush Mounting 40cm ‘SILENCE
PLEASE’ Sign.
LD-40F1PHN Single Flush Mounting 40cm
‘PHONE’ Sign.
40cm ‘RECORD’ Sign
LD-40F1ONA
40cm ‘ON AIR’ Sign
LD-40F1MCL
40cm ‘MIC LIVE’ Sign
LD-40F1PHN
40cm ‘PHONE’ Sign
LD-40F1TRF
40cm ‘TRAFFIC FLAG ON’ Sign
LD-40F1ADB
40cm ‘AD BREAK’ Sign
LD-40F1REH
40cm ‘REHEARSAL’ Sign
LD-40F1DOR
40cm ‘DOOR’ Sign
LD-40F1OBT
40cm ‘OBIT’ Sign
LD-40F1NOE
40cm ‘NO ENTRY’ Sign
LD-40F1EXIT
40cm ‘EXIT’ Sign
LD-40F1SIL
40cm ‘SILENCE PLEASE’ Sign
LD-40F1MET
40cm ‘MEETING IN PROGRESS’ Sign
LD-40F1INT
40cm ‘INTERVIEW IN PROGRESS’ Sign
Twin Flush Mounting Signs (2 x 20cm):
LD-40F2TX-REH
2 x 20cm ‘TX’ & ‘ REH’ Sign
LD-40F2ONA-MCL 2 x 20cm ‘ON AIR’ & ‘MIC LIVE’ Sign
LD-40F1DOR Single Flush Mounting 40cm
‘DOOR’ Sign.
LD-40F1MET Single Flush Mounting 40cm
‘MEETING IN PROGRESS’ Sign.
Single Flush Mounting Signs (20cm):
LD-20F1REC
20cm ‘RECORD’ Sign
LD-20F1ONA
20cm ‘ON AIR’ Sign
LD-20F1MCL
20cm ‘MIC LIVE’ Sign
Mounting Kits:
LD-40F1OBT Single Flush Mounting 40cm
‘OBIT’ Sign.
LD-40F1INT Single Flush Mounting 40cm
‘INTERVIEW IN PROGRESS’ Sign.
LD-KE1
End Mounting Kit For 40cm Or 20cm
Flush Mounting Signs
LD-KC1
Ceiling Mounting Kit For 40cm Or
20cm Flush Mounting Signs
LED Sign End Mounting Installation
Tool
LD-IT
255
www.sonifex.co.uk
UK Office:
Sonifex Ltd
61 Station Road, Irthlingborough,
Northants, NN9 5QE, UK
Tel: +44 (0) 1933 650700
Fax: +44 (0) 1933 650726
Email: [email protected]
Australian Office:
Sonifex Pty Ltd
12/6 Leighton Place,
Hornsby NSW 2077, Australia
Tel: +61 (2) 9987 0499
Fax: +61 (2) 9476 4950
Email: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement