XPar 360 PR-8955
XPar 360
PR-8955
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place
for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com
INDEX
3
4
4
5
5
6
7
9
11
11
11
12
14
15
SAFE USAGE OF THE PROJECTOR
INSTALLING THE PROJECTOR
CONTROL SYSTEM AND POWER CONNECTIONS
DMX TERMINATOR
SETUP OPTIONS-PROJECTOR CONFIGURATION
TO SET THE DMX START ADDRESS
OPERATION MENU
DMX PROTOCOL
INDICATION OF LED DISPLAY
MAINTENANCE
TROUBLESHOOTING
TECHNICAL DATA
ELECTRICAL DIAGRAM
COMPONENT ORDER CODES
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without
notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of
product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence
arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the
unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the projector:
Name
Quantity
Barn door
1
Safety cord
1
This manual
1
Signal cable
1
2/18
Unit
Pc
Pc
Pc
Pc
Remark
Optional
Optional
SAFE USAGE OF THE PROJECTOR
When unpacking and before disposing of the carton, check there is no transportation damage before using the projector.
Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The projector can be used indoors and outdoors, IP20.
The projector is not designed or intended to be mounted directly on to inflammable surfaces.
The projector is only intended for installation, operation and maintenance by qualified personnel.
Do not project the beam onto inflammable surfaces, minimum distance is 5m.
5m
Avoid direct exposure to the light from the lamp. The light is harmful to eyes.
Do not attempt to dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact
with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
Keep the optical system clean. Do not touch the LED lens with bare hands.
When the projector is hanged to a high place, please use a safety cord provided to pass through the projector handles as
a secondary safety fixing for safety seasons. For details, refer to “INSTALL THE PROJECTOR “section.
LED lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for
example by cracks or deep scratches.
Exterior surface temperatures of the projector after 5 minutes operation is 45℃, when achieving steady state it is50℃.
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the
covers removed.
Always disconnect from the mains, when the device is not in use or before cleaning it or
before attempting any maintenance work !
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
3/18
INSTALL THE PROJECTOR
Lamp Hook Mounting Hole
Safety Cable
Support
When the projector is used, as the right figure above, unfold the support to certain angle and put the projector onto a
flat surface. Make sure it is steady.
When the projector is used at a high place, as the left figure above, fold the support, turn it round to the top of the
projector, connect a lamp hook to the mounting hole reserved in the support by screws, and then hang the hook to a high
place. Eventually, use the safety cord provided to pass through the handles and hang it as a second safety fixing.
CONTROL SYSTEM AND POWER CONNECTION
DMX IN
1
DMX512
DMX OUT
2
2
3
1
3
PIN
1
2
3
FUNCTION
GND
DATA DATA +
Connection between the controller and a projector and between one projector and another must be made with a 2
core-screened cable, with each core having at least a 0.5mm diameter. Please use the projector’s cannon 3- pin signal
input and output cables as connection. The 3-pin signal connections are connected as shown in the figure above.
Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of
the plug is not connected in any way. The XPar 360 accepts digital control signals in protocol DMX512 (1990).
The amount of projectors connected in parallel is not more than 32. Connect the controller’s output to the first fixture’s
input cable with a 3-pin signal cable, connect the first fixture’s output cable to the second fixture’s input cable and connect
the rest fixtures in the same way. Eventually, connect the last fixture’s output cable to a DMX terminator. Note: Only when
all the start addresses of fixtures are set the same, synchronous control could be achieved.
When the first fixture is not connected to the controller, and all the other connections are the same as above, it is master /
slave mode connection. To achieve master / slave mode, set the first fixture master , the others salve( slave is default).
As for power connections, each projector has to be supplied separately by external power. Use the power cord of each
projector to connect the mains power directly, paying attention to the voltage and frequency marked on the panel of the
projector.
4/18
All of the connections are as the figure below.
Power IN
Power IN
DMX Controller
DMX OUT
Power IN
DMX OUT
DMX IN
XLR terminator
DMX IN
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This
prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is
then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
DMX TERMINATOR
2
1
3
120
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 2
PIN 3
SETUP OPTIONS-PROJECTOR CONFIGURATION
FUNC
UP
DOWN
ENTER
Projector configuration can be set conveniently via push-button switch and LED display.
Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the
function menu of the projector, each main menu has its submenus and each submenu has a specific function. For
details, please see the “OPERATION MENU” section.
Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your
settings or enter the next menu. Press button UP or DOWN to change values(add or subtract)
5/18
Press button FUNC, it will return to the upper menu one by one or browse through the main menu.
TO SET THE DMX START ADDRESS
Each Xpar360must be given a DMX start address so that the correct projector responds to the correct control signals.
This DMX start address is the channel number from which the projector starts to “listen” to the digital control information
being sent out from the controller. The Xpar360 have 3 DMX modes, which are standard mode,extended mode and
short mode. For example, the standard mode has 12 channels, so set the No. 1 projector’s address 001, No. 2
projector’s address 013, No. 3 projector’s address 025, No. 4 projector’s address 037, and so on.
Launch the projector. Press button ENTER for more than 5 seconds to unlock the panel.
Press button FUNC, UP or DOWN to find “AddR” menu.
Then press ENTER to show DMX address and press UP or DOWN to set DMX address.
At this time, the address will flash continuously. Press button ENTER to confirm and it means the setting has been
enabled.
Press button FUNC, it will return to the upper menu one by one.
6/18
OPERATION MENU
1st LEVEL
2nd LEVEL
AddR
(DMX address)
XXX
(XXX:1~512)
3rd LEVEL
dmX
(DMX mode)
CNFG
(Config settings)
dISP
(Display settings)
mORS
(Master /Slave Settings)
INFO
(Information)
TEST
(Test mode)
FACT
(Reset factory setup)
TRmd
(Transmit parameters)
TImE
(Fixture usage time)
TEmP
(LED board temperature)
VER
(Version)
A
(Amber)
R
(Red)
G
(Blue)
B
(Blue)
W
(white)
RGBW
(Red/green/blue/white)
ALL
(Red/green/blue/white/Amber)
dmx
(DMX mode)
PR XX
(Preset memory, PR01~PR16)
mENU
(Operation mode)
ET XX
(User memory,ET01~ET16)
4th LEVEL
STd
(Standard mode)
EXT
(Extended mode)
SHRT
(Short mode)
ON
OFF
(Shut off digital CRT without
pressing buttons in 5 minutes)
SLAV
(Slave)
mAST
(Master)
yES
yES
XXXX
XX
X.X.X
COL1
(Colour 1)
COL2
(Colour 2)
COL3
(Colour 3)
COL4
(Colour 4)
XX
(Number: 0~14)(3)
XX
(Number: 0~14)
XX
(Number: 0~14)
XX
(Number: 0~14)
Note:
1.ONLY one projector of a group connected by one signal cable could be set as Master. When the Master
functions, DMX control signal should be disconnected
2.When multiple projectors’ work together in synchronous control state, Parameters can be transmitted from the master
projector to the slave projectors such as DMX channel mode, Display setting status and operation mode (User memory
7/18
data is included). While data transmitted, other projectors will be set as SLAVE.
8/18
DMX PROTOCOL
Short
mode
1
Standard
mode
1
2
2
Extended
mode
1
FUNCTION
DMX
Dimmer
000-255
Dimming from dark to light
2
Dimmer Fine
000-255
Dimmer in 16 Bit precision
3
Colour Temperature
000
001-255
0
3
4
Macro Channel
DESCRIPTION
No effect
Colour temperature linear adjustment
No effect
001-015
Low Colour Temperature
016-031
Medium Temperature
032-047
Relatively high Temperature
048-063
High Temperature
064-079
Amber
080-095
Red
096-111
Green
112-127
Blue
128-143
White
144-159
Red & Green(Yellow)
160-175
Green & Blue(Cyan)
176-191
Red and Blue(Purple)
192-207
Red Green Blue and White
208-223
Full Power
224-239
Yellow and White
240-255
Amber Blue and White
3
4
5
Amber
000-255
Linear adjustment from dark to light
4
5
6
Red
000-255
Linear adjustment from dark to light
5
6
7
Green
000-255
Linear adjustment from dark to light
6
7
8
Blue
000-255
Linear adjustment from dark to light
7
8
9
White
000-255
Linear adjustment from dark to light
10
Hue
000-255
Hue selection
11
Saturation
000-255
Saturation from shallow to deep
12
Value
000-255
From dark to light
13
Strobe
14
Preset memory
8
9
10
000
001-255
9/18
000
No effect
Strobe speed from slow to fast
No effect
001-015
Preset memory 1
016-031
Preset memory 2
032-047
Preset memory 3
048-063
Preset memory 4
064-079
Preset memory 5
080-095
Preset memory 6
096-111
Preset memory 7
112-127
Preset memory 8
128-143
Preset memory 9
144-159
Preset memory 10
160-175
Preset memory 11
176-191
Preset memory 12
192-207
Preset memory 13
208-223
Preset memory 14
224-239
Preset memory 15
240-255
Preset memory 16
000
11
12
15
16
User Memory
Memory Speed
10/18
No effect
001-015
User memory 1
016-031
User memory 2
032-047
User memory 3
048-063
User memory 4
064-079
User memory 5
080-095
User memory 6
096-111
User memory 7
112-127
User memory 8
128-143
User memory 9
144-159
User memory 10
160-175
User memory 11
176-191
User memory 12
192-207
User memory 13
208-223
User memory 14
224-239
User memory 15
240-255
User memory 16
001-015
Speed 1,the fastest
016-031
Speed 2
032-047
Speed 3
048-063
Speed 4
064-079
Speed 5
080-095
Speed 6
096-111
Speed 7
112-127
Speed 8
128-143
Speed 9
144-159
Speed 10
160-175
Speed 11
176-191
Speed 12
192-207
Speed 13
208-223
Speed14
224-239
Speed 15
240-255
Speed 16, the slowest
Note:
**** Channel priority from high to low is as the following: Dimming, Preset memory, User memory, ARGBW dimming,
HSV dimming, Macro channel, Color temperature.
****When high priority channel is used, low priority channel is No effect.
11/18
INDICATION OF LED CHARACTER
On
Off
On
Off
On
Off
Flash
Decimal point of the first character
Decimal point of the third character
Decimal point of the fourth character
Parameters that LED characters display
DMX signal OK
No DMX signal
Master / slave signal is OK
No master / slave signal
When setting master mode
When setting slave mode
Parameters not saved, press “ENTER” to save them
MAINTENANCE
To prolong the life of the projector, it is very important to do the maintenance work. Cooling fans must be cleaned once
every 15days and external lens cleaned periodically for an optimum light output. DO NOT USE ANY SOLVENT
CONTAINING CHEMICAL ELEMENT.
Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning
products should be used for cleaning with care. It is recommended to clean projector at least once every 20 days.
Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.
TROUBLESHOOTING
PROBLEM
ACTION
¾
Power connection is not correct.
¾
Power supply is damaged or abnormal. Call a qualified personnel
The projector doesn’t switch on
to fix it.
¾
Connection of control board is not correct. Call a qualified
personnel to fix it.
The projector can be turned on, but LEDs do
¾
not emit light and are out of control.
Connection of LED board is not correct. Call a qualified
personnel to fix it.
The lamp comes on but the projector
¾
Make sure that the projector is correctly configurated.
doesn’t respond to the controller
¾
Replace or repair the DMX cable.
¾
The projector is too hot. Take ventilation measures to make it
The beam appears dim
cool.
12/18
TECHNICAL DATA
VOLTAGES:
100-240V AC, 50/60Hz
POWER CONSUMPTION:
[email protected]
LED:
Power consumption
3W
Quantity
60(13R+13G+13B+12W+9A)
Manufacturers Rated LED Life
50000 Hours
COLOURS:
RGBWA linear color mixing with Macro
COLOR TEMPERATURE CORRECTION
Linear color temperature correction from 3200K to 10000K
DIMMER:
0-100% linearly adjustable
STROBE:
Electronic Strobe 0 ~25F.P.S
LIGHT ANGLE
Light Spot Angle(1/10 Maximum) θ
28°
θ1/2
15°
Beam Angle(1/2 Maximum)
Optional Lens Angle: 8°, 25 °, 45°
CONTROL:
DMX512, 3 pin interfaces
8 channels in short mode, 12channels in standard mode, and 16 channels in extended mode
Master/Salve Synchronous Control Mode
16 preset memories
16 user memories
preset memories and user memories can be called by control channels,16 level speeds adjustable
Self Test Mode
OTHER FUNCTIONS:
LED board temperature display
Fixture usage time display
13/18
Parameters about DMX mode, Display setting status, operation mode can be transmitted by synchronous control.
HOUSING:
High temperature ABS +die-casting aluminum, IP20
WORK ENVIRONMENT TEMPERATURE:
-20°C~40°C
WEIGHT:
3.9kg
SIZES:
277
226
249
321
LIGHT OUTPUT:
28°lux(RGBWA)
28°lux(R)
28°lux(G)
28°lux(B)
28°lux(W)
28°lux(A)
4m
2m
0m
2m
444
197
111
71
49
309
777
77
194
34
86
19
49
12
31
9
22
26
6
3
2
1
1
722
181
80
45
29
20
124
31
14
8
5
3
5m
10m
15m
20m
25m
30m
12.27
14.72
7m
5m
3m
1m
28°
6m
1775
1m
3m
4m
6m
5m
7m
Distance(m)
0m
28°Diameter(m)
0
2.45
4.91
14/18
7.36
9.81
15/18
COMPONENT ORDER CODES
NAME
LED LENS
SIGNAL CABLE
POWER SUPPLY
DRIVER BOARD
LED CONTROL BOARD
LED LAMP BOARD
PART NO.
070070047
242810033
190010119
230060115
230060139
230020283
16/18
QUANTITY
60
1
1
1
1
1
REMARK
15°
5meters
150W58V
17/18
PR LIGHTING LTD.
PR New Hi-tech Science Park, 1582 Xingye Avenue
Nancun Panyu, Guangzhou, 511442 China
TEL: +86-20-3995 2888
FAX: +86-20-3995 2330
P/N: 320020091
Version: 20120717
18/18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement