Data Sheet AFCT-57R5ATPZ SFP, 1310 nm, 10 km, LC Connector, Pluggable Fibre

Data Sheet AFCT-57R5ATPZ SFP, 1310 nm, 10 km, LC Connector, Pluggable Fibre
AFCT-57R5ATPZ
SFP, 1310 nm, 10 km, LC Connector, Pluggable Fibre
Channel 4.25/2.125/1.0625 GBd
Data Sheet
1310 nm, 10 km, SFP (Small Form Pluggable),
Low Voltage (3.3 V) Digital Diagnostic Optical
Transceiver
Description
The AFCT-57R5ATPZ optical transceiver supports
high-speed serial links over singlemode optical fiber
at signaling rates up to 4.25 Gb/s. Compliant with
Small Form Pluggable (SFP) Multi Source Agreement
(MSA) mechanical and electrical specifications, ANSI
Fibre Channel FC-PI-3 and compatible with IEEE
802.3 for gigabit applications.
As an enhancement to the conventional SFP interface
defined in SFF-8074i, the AFCT-57R5ATPZ is
compliant to SFF-8472 (digital diagnostic interface
for SFP). Using the 2-wire serial interface defined in
the SFP MSA, the AFCT-57R5ATPZ provides real
time temperature, supply voltage, laser bias current,
laser average output power and received average
input power. This information is in addition to the
conventional SFP data. The digital diagnostic
interface also adds the ability to disable the
transmitter (TX_DISABLE), monitor for Transmitter
Faults (TX_FAULT), monitor for Receiver Loss of
Signal (RX_LOS).
Installation
The AFCT-57R5ATPZ can be installed in any SFF8074i compliant Small Form Pluggable (SFP) port
regardless of host equipment operating status. The
AFCT-57R5ATPZ is hot-pluggable, allowing the
module to be installed while the host system is
operating and on-line. Upon insertion, the transceiver
housing makes initial contact with the host board
SFP cage, mitigating potential damage due to ElectroStatic Discharge (ESD).
Features
• Diagnostic features per SFF-8472 “Diagnostic Monitoring
Interface for Optical Transceivers”
• Compliant to Restriction on Hazardous Substances (RoHS)
directive
• Real time monitors of:
– Transmitted average optical power
– Received average optical power
– Laser bias current
– Temperature
– Supply voltage
• High performance 1310 nm DFB laser
• Wide Temperature and Supply Voltage Operation
(-10°C to 85°C) (3.3 V ± 10%)
• Transceiver specifications per SFP (SFF-8074i) Multi-Source
Agreement and SFF-8472 (revision 9.3)
– 4.25 GBd Fibre Channel operation for FC-PI-2 400-SM-LC-L
– 2.125 GBd Fibre Channel operation for FC-PI-2 200-SM-LC-L
– 1.0625 GBd Fibre Channel operation for FC-PI-2 100-SM-LC-L
• Link lengths at 4.25 GBd: 10 km with 9 µm SMF
• Link lengths at 2.125 GBd: 10 km with 9 µm SMF
• Link lengths at 1.0625 GBd: 10 km with 9 µm SMF
• LC Duplex optical connector interface conforming to ANSI
TIA/EIA604-10 (FOCIS 10)
• IEC 60825-1 Class 1/CDRH Class 1 laser eye safe
Applications
• Fibre channel systems
– Director class switches
– Fabric switches
– HBA cards
• Disk and tape drive arrays
Related Products
• AFBR-59R5LZ: 850 nm +3.3 V LC SFF 2x7 for 4.25/2.125/
1.0625 GBd Fibre Channel
• AFBR-57R5APZ: 850 nm +3.3 V LC SFP for 4.25/2.125/1.0625
GBd Fibre Channel
• AFCT-57R5APZ: 1310 nm +3.3 V LC SFP for 4.25/2.125/1.0625
GBd Fibre Channel Over 4 km
Digital Diagnostic Interface
and Serial Identification
The 2-wire serial interface is
based on ATMEL AT24C01A
series EEPROM protocol and
signaling detail. Conventional
SFP EEPROM memory, bytes
0-255 at memory address 0xA0,
is organized in compliance with
SFF-8074i. New digital
diagnostic information, bytes
0-255 at memory address 0xA2,
is compliant to SFF-8472. The
new diagnostic information
provides the opportunity for
Predictive Failure Identification,
Compliance Prediction, Fault
Isolation and Component
Monitoring.
Predictive Failure Identification
The AFCT-57R5ATPZ predictive
failure feature allows a host to
identify potential link problems
before system performance is
impacted. Prior identification of
link problems enables a host to
service an application via “fail
over” to a redundant link or
replace a suspect device, maintaining system uptime in the
process. For applications where
ultra-high system uptime is
required, a digital SFP provides
a means to monitor two realtime laser metrics associated
with observing laser degradation
and predicting failure: average
laser bias current (Tx_Bias) and
average laser optical power
(Tx_Power).
2
Compliance Prediction
Compliance prediction is the
ability to determine if an optical
transceiver is operating within
its operating and environmental
requirements. AFCT-57R5ATPZ
devices provide real-time access
to transceiver internal supply
voltage and temperature,
allowing a host to identify
potential component compliance
issues. Received optical power is
also available to assess
compliance of a cable plant and
remote transmitter. When
operating out of requirements,
the link cannot guarantee error
free transmission.
Fault Isolation
The fault isolation feature allows
a host to quickly pinpoint the
location of a link failure,
minimizing downtime. For
optical links, the ability to
identify a fault at a local device,
remote device or cable plant is
crucial to speeding service of an
installation. AFCT-57R5ATPZ
real-time monitors of Tx_Bias,
Tx_Power, Vcc, Temperature
and Rx_Power can be used to
assess local transceiver current
operating conditions. In
addition, status flags Tx_Disable
and Rx Loss of Signal (LOS) are
mirrored in memory and
available via the two-wire serial
interface.
Component Monitoring
Component evaluation is a more
casual use of the AFCT57R5ATPZ real-time monitors of
Tx_Bias, Tx_Power, Vcc,
Temperature and Rx_Power.
Potential uses are as debugging
aids for system installation and
design, and transceiver
parametric evaluation for
factory or field qualification. For
example, temperature per
module can be observed in high
density applications to facilitate
thermal evaluation of blades,
PCI cards and systems.
OPTICAL INTERFACE
ELECTRICAL INTERFACE
RECEIVER
LIGHT FROM FIBER
PHOTO-DETECTOR
AMPLIFICATION
& QUANTIZATION
RD+ (RECEIVE DATA)
RD– (RECEIVE DATA)
Rx LOSS OF SIGNAL
MOD-DEF2 (SDA)
CONTROLLER & MEMORY
MOD-DEF1 (SCL)
MOD-DEF0
TRANSMITTER
LIGHT TO FIBER
VCSEL
TX_DISABLE
LASER
DRIVER &
SAFETY
CIRCUITRY
TD+ (TRANSMIT DATA)
TD– (TRANSMIT DATA)
TX_FAULT
Figure 1. Transceiver functional diagram.
Transmitter Section
The transmitter section includes
a 1310-nm distributed feedback
(DFB) laser and a transmitter
driver circuit. The driver circuit
maintains a constant average
optical power output with Fibre
Channel and Ethernet 8B/10B
coded data. Optical connection
to the transmitter is provided
via an LC connector. The TOSA
is driven by a custom IC which
uses the incoming differential
high speed logic signal to
modulate the laser diode driver
current. This Tx laser driver
circuit regulates the optical
power at a constant level
provided the incoming data
pattern is dc balanced (8B/10B
code, for example).
Transmit Disable (TX_DISABLE)
The AFCT-57R5ATPZ accepts a
TTL and CMOS compatible
transmit disable control signal
input (pin 3) which shuts down
the transmitter optical output. A
high signal implements this
3
function while a low signal
allows normal transceiver
operation. In the event of a fault
(e.g. eye safety circuit activated),
cycling this control signal resets
the module as depicted in Figure
4. An internal pull up resistor
disables the transceiver
transmitter until the host pulls
the input low. Host systems
should allow a 10 ms interval
between successive assertions of
this control signal. Tx_Disable
can also be asserted via the twowire serial interface (address
A2h, byte 110, bit 6) and
monitored (address A2h, byte
110, bit 7).
The contents of A2h, byte 110,
bit 6 are logic OR’d with
hardware Tx_Disable (pin 3) to
control transmitter operation
Transmit Fault (TX_FAULT)
A catastrophic laser fault will
activate the transmitter signal,
TX_FAULT, and disable the
laser. This signal is an open
collector output (pull-up
required on the host board). A
low signal indicates normal laser
operation and a high signal
indicates a fault. The TX_FAULT
will be latched high when a laser
fault occurs and is cleared by
toggling the TX_DISABLE input
or power cycling the transceiver.
The transmitter fault condition
can also be monitored via the
two-wire serial interface
(address A2, byte 110, bit 2).
Eye Safety Circuit
The AFCT-57R5ATPZ provides
Class 1 (single fault tolerant) eye
safety by design and has been
tested for compliance with the
requirements listed in Table 1.
The eye safety circuit
continuously monitors the
optical output power level and
will disable the transmitter upon
detecting an unsafe condition
beyond the scope of Class 1
certification. Such unsafe
conditions can be due to inputs
from the host board (Vcc
fluctuation, unbalanced code) or
a fault within the transceiver.
Receiver Section
The receiver section includes the
Receiver Optical SubAssembly
(ROSA) and the amplification/
quantization circuitry. The
ROSA, containing a PIN photodiode and custom transimpedance amplifier, is located at the
optical interface and mates with
the LC optical connector. The
ROSA output is fed to a custom
IC that provides postamplification and quantization.
Receiver Loss of Signal (Rx_LOS)
The post-amplification IC also
includes transition detection
circuitry which monitors the ac
level of incoming optical signals
and provides a TTL/CMOS
compatible status signal to the
host (pin 8). An adequate optical
input results in a low Rx_LOS
output while a high Rx_LOS
output indicates an unusable
optical input. The Rx_LOS
thresholds are factory set so that
a high output indicates a definite
optical fault has occurred.
Rx_LOS can also be monitored
via the two-wire serial interface
(address A2h, byte 110, bit 1).
Functional Data I/O
The AFCT-57R5ATPZ interfaces
with the host circuit board
through twenty I/O pins (SFP
electrical connector) identified
by function in Table 2. The
board layout for this interface is
depicted in Figure 6.
The AFCT-57R5ATPZ high speed
transmit and receive interfaces
require SFP MSA compliant
signal lines on the host board. To
simplify board requirements,
biasing resistors and ac coupling
capacitors are incorporated into
4
the SFP transceiver module (per
SFF-8074i) and hence are not
required on the host board. The
Tx_Disable, Tx_Fault, Rx_LOS
require TTL lines on the host
board (per SFF-8074i) if used. If
an application chooses not to
take advantage of the
functionality of these pins, care
must be taken to ground
Tx_Disable (for normal
operation).
Figure 2 depicts the
recommended interface circuit
to link the AFCT-57R5ATPZ to
supporting physical layer ICs.
Timing for MSA compliant
control signals implemented in
the transceiver are listed in
Figure 4.
Application Support
An Evaluation Kit and Reference
Designs are available to assist in
evaluation of the AFCT57R5ATPZ. Please contact your
local Field Sales representative
for availability and ordering
details.
Caution
There are no user serviceable
parts nor maintenance requirements for the AFCT-57R5ATPZ.
All mechanical adjustments are
made at the factory prior to
shipment. Tampering with,
modifying, misusing or
improperly handling the AFCT57R5ATPZ will void the product
warranty. It may also result in
improper operation and possibly
overstress the laser source.
Performance degradation or
device failure may result.
Connection of the AFCT57R5ATPZ to a light source not
compliant with ANSI FC-PI or
IEEE 802.3 specifications,
operating above maximum
operating conditions or in a
manner inconsistent with it’s
design and function may result in
exposure to hazardous light
radiation and may constitute an
act of modifying or manufacturing a laser product. Persons
performing such an act are
required by law to re-certify and
re-identify the laser product
under the provisions of U.S. 21
CFR (Subchapter J) and TUV.
Ordering Information
Please contact your local field sales
engineer or one of Avago
Technologies franchised distributors
for ordering information. For
technical information, please visit
Avago Technologies’ WEB page at
www.avagotech.com or contact
Avago Technologies Semiconductor
Products Customer Response Center
at 1-800-235-0312. For information
related to SFF Committee
documentation visit
www.sffcommittee.org.
Regulatory Compliance
The AFCT-57R5ATPZ complies with
all applicable laws and regulations as
detailed in Table 1. Certification level
is dependent on the overall
configuration of the host equipment.
The transceiver performance is
offered as a figure of merit to assist
the designer.
Electrostatic Discharge (ESD)
The AFCT-57R5ATPZ is compatible
with ESD levels found in typical
manufacturing and operating
environments as described in Table
1. In the normal handling and operation of optical transceivers, ESD is
of concern in two circumstances.
The first case is during handling of
the transceiver prior to insertion into
an SFP compliant cage. To protect
the device, it’s important to use
normal ESD handling precautions.
These include using of grounded
wrist straps, work-benches and floor
wherever a transceiver is handled.
The second case to consider is static
discharges to the exterior of the host
equipment chassis after installation.
If the optical interface is exposed to
the exterior of host equipment
cabinet, the transceiver may be
subject to system level ESD
requirements.
Electromagnetic Interference (EMI)
Equipment incorporating gigabit
transceivers is typically subject to
regulation by the FCC in the United
States, CENELEC EN55022 (CISPR
22) in Europe and VCCI in Japan.
The AFCT-57R5ATPZ’s compliance
to these standards is detailed in
Table 1. The metal housing and
shielded design of the AFCT57R5ATPZ minimizes the EMI
challenge facing the equipment
designer.
EMI Immunity (Susceptibility)
Due to its shielded design, the EMI
immunity of the AFCT-57R5ATPZ
exceeds typical industry standards.
Flammability
The AFCT-57R5ATPZ optical
transceiver is made of metal and
high strength, heat resistant,
chemical resistant and UL 94V-0
flame retardant plastic.
Table 1. Regulatory Compliance
Feature
Test Method
Performance
Electrostatic Discharge (ESD)
to the Electrical Pins
MIL-STD-883C
Method 3015.4
Class 2 (> 2000 Volts)
Electrostatic Discharge (ESD)
to the Duplex LC Receptacle
Variation of IEC 61000-4-2
Typically, no damage occurs with 25 kV when
the duplex LC connector receptacle is
contacted by a Human Body Model probe.
GR1089
10 contacts of 8 kV on the electrical faceplate
with device inserted into a panel.
Electrostatic Discharge (ESD)
to the Optical Connector
Variation of IEC 801-2
Air discharge of 15 kV (min.) contact to
connector without damage.
Electromagnetic Interference
(EMI)
FCC Class B
CENELEC EN55022 Class B
(CISPR 22A)
VCCI Class 1
System margins are dependent on customer
board and chassis design.
Immunity
Variation of IEC 61000-4-3
Typically shows no measurable effect
from a 10 V/m swept from 10 MHZ to 1 GHz.
Laser Eye Safety and
Equipment Type Testing
US FDA CDRH AEL Class 1
US21 CFR, Subchapter J per
Paragraphs 1002.10 and 1002.12
CDRH #9521220-141
TUV #933/21205741/010
BAUART
¨
GEPRUFT
¨
TUV
Rheinland
Product Safety
TYPE
APPROVED
Component Recognition
Restriction on Hazardous
Substances (RoHS) Compliance
5
(IEC) EN60825-1: 1994 + A11 + A2
(IEC) EN60825-2: 1994 + A1
(IEC) EN60950: 1992 + A1 + A2 +
A3 + A4 + A11
Underwriters Laboratories and
Canadian Standards Association
Joint Component Recognition
for Information Technology
Equipment including Electrical
Business Equipment
UL #E173874
Less than 1000 ppm of cadmium, lead, mercury,
hexavalent chromium, polybrominated biphenyls,
and polybrominated biphenyl ethers.
VCC,T
GND,T
6.8 kΩ
Tx DIS
Tx_DISABLE
Tx FAULT
Tx_FAULT
TD+
100 Ω
TD–
LASER DRIVER
4.7 k to 10 kΩ
1 µH
VCC,T
0.1 µF
3.3 V
10 µF
SERDES IC
PROTOCOL IC
0.1 µF
1 µH
10 µF
VCC,R
VCC,R
VCC,R
0.1 µF
50 Ω
4.7 k to
10 kΩ
50 Ω
RD+
100 Ω
RD–
Rx LOS
LOSS OF SIGNAL
POST AMPLIFIER
3.3 V
GND,R
4.7 k to 10 kΩ
4.7 k to 10 kΩ
MOD_DEF0
4.7 k to 10 kΩ
MODULE DETECT
SCL
SDA
Figure 2. Typical application configuration.
1 µH
VCCT
0.1 µF
1 µH
3.3 V
VCCR
0.1 µF
SFP MODULE
10 µF
0.1 µF
10 µF
HOST BOARD
NOTE: INDUCTORS MUST HAVE LESS THAN 1 Ω SERIES RESISTANCE TO LIMIT VOLTAGE DROP TO THE SFP MODULE.
Figure 3. Recommended power supply filter.
6
MOD_DEF1
MOD_DEF2
Table 2. Pin Description
Pin
Name
Function/Description
Notes
1
VeeT
Transmitter Ground
2
TX_FAULT
Transmitter Fault Indication – High indicates a fault condition
Note 1
3
TX_DISABLE
Transmitter Disable – Module optical output disables on high or open
Note 2
4
MOD-DEF2
Module Definition 2 – Two wire serial ID interface data line (SDA)
Note 3
5
MOD-DEF1
Module Definition 1 – Two wire serial ID interface clock line (SCL)
Note 3
6
MOD-DEF0
Module Definition 0 – Grounded in module (module present indicator)
Note 3
7
N.C.
8
RX_LOS
Loss of Signal – High indicates loss of received optical signal
Note 4
9
VeeR
Receiver Ground
10
VeeR
Receiver Ground
11
VeeR
Receiver Ground
12
RD-
Inverse Received Data Out
Note 5
13
RD+
Received Data Out
Note 5
14
VeeR
Receiver Ground
15
VccR
Receiver Power + 3.3 V
Note 6
16
VccT
Transmitter Power + 3.3 V
Note 6
17
VeeT
Transmitter Ground
18
TD+
Transmitter Data In
Note 7
19
TD-
Inverse Transmitter Data In
Note 7
20
VeeT
Transmitter Ground
Notes:
1. TX_FAULT is an open collector/drain output, which must be pulled up with a 4.7 k – 10 kΩ resistor on the host board. When high, this output
indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.
2. TX_DISABLE is an input that is used to shut down the transmitter optical output. It is internally pulled up (within the transceiver) with a 6.8 kΩ
resistor.
Low (0 – 0.8 V):
Transmitter on
Between (0.8 V and 2.0 V):
Undefined
High (2.0 – Vcc max) or OPEN:
Transmitter Disabled
3. The signals Mod-Def 0, 1, 2 designate the two wire serial interface pins. They must be pulled up with a 4.7 k – 10 kΩ resistor on the host board.
Mod-Def 0 is grounded by the module to indicate the module is present
Mod-Def 1 is serial clock line (SCL) of two wire serial interface
Mod-Def 2 is serial data line (SDA) of two wire serial interface
4. RX_LOS (Rx Loss of Signal) is an open collector/drain output that must be pulled up with a 4.7 k – 10 kΩ resistor on the host board. When high, this
output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates normal
operation. In the low state, the output will be pulled to < 0.8 V.
5. RD-/+ designate the differential receiver outputs. They are AC coupled 100 Ω differential lines which should be terminated with 100 Ω differential
at the host SERDES input. AC coupling is done inside the transceiver and is not required on the host board. The voltage swing on these lines will be
between 600 and 1600 mV differential (300 – 800 mV single ended) when properly terminated.
6. VccR and VccT are the receiver and transmitter power supplies. They are defined at the SFP connector pin. The maximum supply current is 300 mA
and the associated in-rush current will typically be no more than 30 mA above steady state after 2 microseconds.
7. TD-/+ designate the differential transmitter inputs. They are AC coupled differential lines with 100 Ω differential termination inside the module. The
AC coupling is done inside the module and is not required on the host board. The inputs will accept differential swings of 400 – 2400 mV (200 –
1200 mV single ended), although it is recommended that values between 500 mV and 1200 mV differential (250-600 mV single ended) be used for
best EMI.
7
Table 3. Absolute Maximum Ratings
Parameter
Symbol
Minimum
Maximum
Unit
Notes
Storage Temperature
TS
-40
100
C
Note 1, 2
Case Operating Temperature
TC
-10
85
C
Note 1, 2
Relative Humidity
RH
5
85
%
Note 1
Supply Voltage
VccT, R
-0.5
3.8
V
Note 1, 2, 3
Low Speed Input Voltage
VIN
-0.5
Vcc + 0.5
V
Note 1
Notes;
1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short
period of time. See Reliability Data Sheet for specific reliability performance.
2. Between Absolute Maximum Ratings and the Recommended Operating Conditions functional performance is not intended, device reliability is not
implied, and damage to the device may occur over an extended period of time.
3. The module supply voltages, VCCT and VCCR must not differ by more than 0.5 V or damage to the device may occur.
Table 4. Recommended Operating Conditions
Parameter
Symbol
Minimum
Maximum
Unit
Notes
Supply Voltage
VccT, R
2.97
3.63
V
Note 2
Data Rate
1.0625
4.25
Gb/s
Note 2
Tcase
-10
85
°C
Note 1, 2
Notes:
1. The Ambient Operating Temperature limitations are based on the Case Operating Temperature limitations and are subject to the host system
thermal design.
2. Recommended Operating Conditions are those values for which functional performance and device reliability is implied.
Table 5. Transceiver Electrical Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ± 10%)
Parameter
Symbol
Minimum
Typical
Maximum
Unit
Notes
AC Electrical Characteristics
Power Supply Noise Rejection (peak-peak)
PSNR
100
Module Supply Current
ICC
215
Power Dissipation
PDISS
Low Speed Outputs:
Transmit Fault (TX_FAULT), Loss of Signal
(RX_LOS), MOD-DEF 2
VOH
mV
Note 1
DC Electrical Characteristics
Low Speed Inputs:
Transmit Disable (TX_DIS),
MOD-DEF 1, MOD-DEF 2
2.0
VOL
1000
mW
VccT,R+0.3
V
0.8
V
VIH
2.0
Vcc
V
VIL
0
0.8
V
Notes:
1. Filter per SFP specification is required on host board to remove 10 Hz to 2 MHz content.
2. Pulled up externally with a 4.7 k – 10 kΩ resistor on the host board to 3.3 V.
3. Pulled up externally with a 4.7 k – 10 kΩ resistor on the host board to 3.3 V.
8
300 mA @ 70°C
350 mA @ 85°C
Note 2
Note 3
Table 6. Transmitter and Receiver Electrical Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ± 10%)
Parameter
Symbol
Minimum
High Speed Data Input:
Transmitter Differential Input Voltage (TD +/-)
VI
High Speed Data Output:
Receiver Differential Output Voltage (RD +/-)
Vo
Receiver Contributed Total Jitter
(4.25 Gb/s)
TJ
Receiver Contributed Total Jitter
(2.125 Gb/s)
TJ
Receiver Contributed Total Jitter
(1.0625 Gb/s)
TJ
Receiver Electrical Output Rise & Fall Times
(20-80%)
tr, tf
Maximum
Unit
Notes
400
2400
mV
Note 1
600
1600
mV
Note 2
0.26
UI
Note 3
61
ps
0.26
UI
122
ps
0.20
UI
188
ps
150
ps
50
Typical
100
Note 3
Note 3
Note 4
Notes:
1. Internally AC coupled and terminated (100 Ohm differential).
2. Internally AC coupled but requires an external load termination (100 Ohm differential).
3. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern. Contributed TJ is the sum of contributed RJ
and contributed J. Contributed RJ is calculated for 1x10-12 BER by multiplying the RMS jitter (measured on a single rise or fall edge) from the
oscilloscope by 14. Per FC-PI-2 (Table 9 - SM jitter output, note 1), the actual contributed RJ is allowed to increase above its limit if the actual
contributed DJ decreases below its limits, as long as the component output DJ and TJ remain within their specified FC-PI-2 maximum limits with
the worst case specified component jitter input.
4. 20%-80% electrical rise & fall times measured with a 500 MHz signal utilizing a 1010 data pattern.
9
Table 7. Transmitter Optical Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ± 10%)
Parameter
Symbol
Minimum Typical
Modulated Optical Output Power (OMA)
(Peak-to-Peak) 4.25 Gb/s
Tx,OMA
290
Modulated Optical Output Power (OMA)
(Peak-to-Peak) 2.125 Gb/s
Tx,OMA
Modulated Optical Output Power (OMA)
(Peak-to-Peak) 1.0625 Gb/s
Maximum
Unit
Notes
350
µW
Note 6
290
350
µW
Note 3
Tx,OMA
290
350
µW
Note 4
Average Optical Output Power
Pout
-8.4
-3.0
dBm
Note 1, 2
Center Wavelength
lC
1290
1340
nm
Note 3, 4, 6
Spectral Width – rms
s,rms
nm
Note 3, 4, 6
Optical Rise/Fall Time (4.25 Gb/s)
tr, tf
90
ps
20% - 80%
RIN 12 (OMA)
RIN
-118
dB/Hz
Transmitter Contributed Total Jitter
(4.25 Gb/s)
TJ
0.25
UI
60
ps
Transmitter Contributed Total Jitter
(2.125 Gb/s)
TJ
0.25
UI
120
ps
Transmitter Contributed Total Jitter
(1.0625 Gb/s)
TJ
0.27
UI
252
ps
Pout TX_DISABLE Asserted
POFF
-35
dBm
Note 5
Note 5
Note 5
Notes:
1. Max Pout is the lesser of Class 1 safety limits (CDRH and EN 60825) or receiver power, max.
2. Into 9/125 µm single-mode optical fiber.
3. OMA, center wavelength and spectral width must comply with FC-PI clause 6.3.5, Figure 19 (200-SM-LC-L triple trade-off curve).
4. OMA, center wavelength and spectral width must comply with FC-PI clause 6.3.5, Figure 18 (100-SM-LC-L triple trade-off curve).
5. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern. Contributed TJ is the sum of contributed RJ
and contributed DJ. Contributed RJ is calculated for 1x10-12 BER by multiplying the RMS jitter (measured on a single rise or fall edge) from the
oscilloscope by 14. Per FC-PI (Table 9 - SM jitter output, note 1), the actual contributed RJ is allowed to increase above its limit if the actual
contributed DJ decreases below its limits, as long as the component output DJ and TJ remain within their specified FC-PI maximum limits with the
worst case specified component jitter input.
6. OMA, center wavelength and spectral width must comply with FC-PI-2 clause 6.3.5, Figure 20 (400-SM-LC-L triple trade-off curve).
10
Table 8. Receiver Optical Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ± 10%)
Parameter
Symbol
Input Optical Power [Overdrive]
PIN
Input Optical Modulation Amplitude (Peak-to-Peak)
4.25 Gb/s [Sensitivity]
OMA
29
µW, oma
Notes 2, 4
Input Optical Modulation Amplitude (Peak-to-Peak)
2.125 Gb/s [Sensitivity]
OMA
15
µW, oma
Notes 1, 4
Input Optical Modulation Amplitude (Peak-to-Peak)
1.0625 Gb/s [Sensitivity]
OMA
15
µW, oma
Notes 1, 4
12
dB
Return Loss
Loss of Signal – Assert
Min.
PA
-30
Loss of Signal – De-Assert
Loss of Signal Hysteresis
PD
PD - P A
0.5
Typ.
Max.
Unit
-3
dBm, avg
13.8
µW, oma
-20.5
dBm, avg
15
µW, oma
-20.0
dBm, avg
Notes
Note 3
Note 3
dB
Notes:
1. For illustrative purposes, consider the an example where an OMA of 15 µW is approximately equal to an average power of –20 dBm, avg. with an
Extinction Ratio of 9 dB.
2. For illustrative purposes, consider the an example where an OMA of 29 µW is approximately equal to an average power of –17.3 dBm, avg. with an
Extinction Ratio of 9 dB.
3. These average power values are specified with an Extinction Ratio of 9 dB. The loss of signal circuitry responds to valid 8B/10B encoded peak to
peak input optical power, not average power.
4. Input Optical Modulation Amplitude (commonly known as sensitivity) requires a valid 8B/10B encoded input.
11
Table 9. Transceiver Timing Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ± 10%)
Parameter
Symbol
Hardware TX_DISABLE Assert Time
Minimum
Maximum
Unit
Notes
t_off
10
µs
Note 1
Hardware TX_DISABLE Negate Time
t_on
1
ms
Note 2
Time to initialize, including reset of TX_FAULT
t_init
300
ms
Note 3
Hardware TX_FAULT Assert Time
t_fault
100
µs
Note 4
Hardware TX_DISABLE to Reset
t_reset
µs
Note 5
Hardware RX_LOS DeAssert Time
t_loss_on
100
µs
Note 6
Hardware RX_LOS Assert Time
t_loss_off
100
µs
Note 7
Software TX_DISABLE Assert Time
t_off_soft
100
ms
Note 8
Software TX_DISABLE Negate Time
t_on_soft
100
ms
Note 9
Software Tx_FAULT Assert Time
t_fault_soft
100
ms
Note 10
Software Rx_LOS Assert Time
t_loss_on_soft
100
ms
Note 11
Software Rx_LOS De-Assert Time
t_loss_off_soft
100
ms
Note 12
Analog parameter data ready
t_data
1000
ms
Note 13
Serial bus hardware ready
t_serial
300
ms
Note 14
Write Cycle Time
t_write
10
ms
Note 15
Serial ID Clock Rate
f_serial_clock
400
kHz
10
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured
from falling clock edge after stop bit of write transaction.
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of nominal.
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1-8 byte write command.
12
Table 10. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
(TC = -15°C to 85°C, VccT, VccR = 3.3 V ± 10%)
Parameter
Symbol
Min.
Units
Notes
Transceiver Internal Temperature
Accuracy
TINT
±3.0
°C
Temperature is measured internal to the transceiver.
Valid from = -10°C to 85°C case temperature.
Transceiver Internal Supply
Voltage Accuracy
VINT
±0.1
V
Supply voltage is measured internal to the transceiver
and can, with less accuracy, be correlated to
voltage at the SFP Vcc pin. Valid over 3.3 V ± 10%.
Transmitter Laser DC Bias Current
Accuracy
IINT
±10
%
IINT is better than ±10% of the nominal value.
Transmitted Average Optical
Output Power Accuracy
PT
±3.0
dB
Coupled into 9/125 µm single-mode fiber. Valid from
100 µW to 500 µW, average.
Received Optical Input Power
Accuracy
PR
±3.0
dB
Coupled from 9/125 µm single-mode fiber. Valid from
15 µW to 500 µW, average.
13
VCCT,R > 2.97 V
VCCT,R > 2.97 V
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_init
t_init
t-init: TX DISABLE NEGATED
t-init: TX DISABLE ASSERTED
VCCT,R > 2.97 V
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_off
t_on
t_init
INSERTION
t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED
t-off & t-on: TX DISABLE ASSERTED THEN NEGATED
OCCURANCE OF FAULT
OCCURANCE OF FAULT
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_fault
* SFP SHALL CLEAR TX_FAULT IN
< t_init IF THE FAILURE IS TRANSIENT
t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED
t_reset
t_init*
t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED
OCCURANCE OF FAULT
TX_FAULT
LOS
TRANSMITTED SIGNAL
t_fault
* SFP SHALL CLEAR TX_FAULT IN
< t_init IF THE FAILURE IS TRANSIENT
t_loss_on
t_reset
t_init*
t-fault: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL NOT RECOVERED
t-loss-on & t-loss-off
Figure 4. Transceiver timing diagrams (module installed except where noted).
14
OCCURANCE
OF LOSS
OPTICAL SIGNAL
TX_DISABLE
t_loss_off
Table 12. EEPROM Serial ID Memory Contents – Conventional SFP Memory (Address A0h)
Byte # Data
Decimal Hex
Notes
Byte #
Decimal
Data
Hex
Notes
0
03
SFP physical device
37
00
Hex Byte of Vendor OUI[2]
1
04
SFP function defined by serial ID only
38
17
Hex Byte of Vendor OUI[2]
2
07
LC optical connector
39
6A
Hex Byte of Vendor OUI[2]
3
00
40
41
“A” - Vendor Part Number ASCII character
4
00
41
46
“F” - Vendor Part Number ASCII character
5
00
42
43
“C” - Vendor Part Number ASCII character
6
00
7
12
43
54
“T” - Vendor Part Number ASCII character
44
2D
“-” - Vendor Part Number ASCII character
8
00
45
35
“5” - Vendor Part Number ASCII character
9
01
10
15
Single Mode (SM)
46
37
“7” - Vendor Part Number ASCII character
100, 200 & 400 Mbytes/sec FC-PI speed[1]
47
52
“R” - Vendor Part Number ASCII character
11
01
Compatible with 8B/10B encoded data
48
35
“5” - Vendor Part Number ASCII character
12
2B
4300 MBit/sec nominal bit rate (4.25 Gbit/s)
41
41
“A” - Vendor Part Number ASCII character
13
00
54
54
“T” - Vendor Part Number ASCII character
14
0A
10 km of 9 µm/125 µm single mode fiber
50
50
“P” - Vendor Part Number ASCII character
15
64
10 km of 9 µm/125 µm single mode fiber
5A
5A
“Z” - Vendor Part Number ASCII character
16
00
53
20
“ ” - Vendor Part Number ASCII character
17
00
54
20
“ ” - Vendor Part Number ASCII character
18
00
55
20
“ ” - Vendor Part Number ASCII character
19
00
56
20
“ ” - Vendor Part Number ASCII character
20
41
“A” - Vendor Name ASCII character
57
20
“ ” - Vendor Part Number ASCII character
21
56
“V” - Vendor Name ASCII character
58
20
“ ” - Vendor Part Number ASCII character
22
41
“A” - Vendor Name ASCII character
59
20
“ ” - Vendor Part Number ASCII character
23
47
“G” - Vendor Name ASCII character
60
05
Hex Byte of Laser Wavelength[3]
24
4F
“O” - Vendor Name ASCII character
61
1E
Hex Byte of Laser Wavelength[3]
25
20
“ ” - Vendor Name ASCII character
62
00
26
20
“ ” - Vendor Name ASCII character
63
27
20
“ ” - Vendor Name ASCII character
64
00
28
20
“ ” - Vendor Name ASCII character
65
1A
29
20
“ ” - Vendor Name ASCII character
66
00
00
Long distance (per FC-PI), Longwave Laser (LC)
Checksum for Bytes 0-62[4]
Hardware SFP TX_DISABLE, TX_FAULT,
& RX_LOS
30
20
“ ” - Vendor Name ASCII character
67
31
20
“ ” - Vendor Name ASCII character
68-83
Vendor Serial Number ASCII characters[5]
32
20
“ ” - Vendor Name ASCII character
84-91
Vendor Date Code ASCII characters[6]
33
20
“ ” - Vendor Name ASCII character
92
68
Digital Diagnostics, Internal Cal, Rx Pwr Avg
34
20
“ ” - Vendor Name ASCII character
93
F0
A/W, Soft SFP TX_DISABLE, TX_FAULT,
& RX_LOS
35
20
“ ” - Vendor Name ASCII character
94
01
SFF-8472 Compliance to revision 9.3
36
00
Checksum for Bytes 64-94[4]
95
96 - 255
00
Notes:
1. FC-PI speed 100 MBytes/sec is a serial bit rate of 1.0625 GBit/sec. 200 MBytes/sec is a serial bit rate of 2.125 GBit/sec. 400 MBytes/sec is a
serial bit rate of 4.25 GBit/sec.
2. The IEEE Organizationally Unique Identifier (OUI) assigned to Avago Technologies is 00-17-6A (3 bytes of hex).
3. Laser wavelength is represented in 16 unsigned bits. The hex representation of 1310 (nm) is 051E.
4. Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment.
5. Addresses 68-83 specify the AFCT-57R5ATPZ ASCII serial number and will vary on a per unit basis.
6. Addresses 84-91 specify the AFCT-57R5ATPZ ASCII date code and will vary on a per date code basis.
15
Table 13: EEPROM Serial ID Memory Contents – Enhanced Feature Set Memory (Address A2h)
Byte #
Decimal Notes
Byte #
Decimal Notes
Byte #
Decimal Notes
0
Temp H Alarm MSB[1]
26
Tx Pwr L Alarm MSB[4]
104
Real Time Rx average
MSB[5]
1
Temp H Alarm LSB[1]
27
Tx Pwr L Alarm LSB[4]
105
Real Time Rx average
LSB[5]
2
Temp L Alarm MSB[1]
28
Tx Pwr H Warning MSB[4]
LSB[1]
106
Reserved
29
Tx Pwr H Warning
LSB[4]
107
Reserved
3
Temp L Alarm
4
Temp H Warning MSB[1]
30
Tx Pwr L Warning MSB[4]
108
Reserved
5
Temp H Warning LSB[1]
31
Tx Pwr L Warning LSB[4]
109
Reserved
6
Temp L Warning
MSB[1]
110
Status/Control - See
Table 14
7
MSB[5]
32
Rx Pwr H Alarm
Temp L Warning LSB[1]
33
Rx Pwr H Alarm LSB[5]
111
Reserved
8
Vcc H Alarm MSB[2]
34
Rx Pwr L Alarm MSB[5]
112
Flag Bits - See Table 15
9
Vcc H Alarm LSB[2]
35
Rx Pwr L Alarm LSB[5]
113
Flag Bits - See Table 15
Rx Pwr H Warning
MSB[5]
114
Reserved
37
Rx Pwr H Warning
LSB[5]
115
Reserved
Vcc L Alarm
MSB[2]
11
Vcc L Alarm
LSB[2]
12
Vcc H Warning MSB[2]
38
Rx Pwr L Warning MSB[5]
116
Flag Bits - See Table 15
13
Vcc H Warning LSB[2]
39
Rx Pwr L Warning LSB[5]
117
Flag Bits - See Table 15
14
Vcc L Warning
MSB[2]
40-55
Reserved
118-127
Reserved
15
Vcc L Warning
LSB[2]
128-247
Customer Writeable
16
248-255
Vendor Specific
10
36
Constants[6]
56-94
External Calibration
Tx Bias H Alarm MSB[3]
95
Checksum for Bytes 0-94[7]
17
Tx Bias H Alarm LSB[3]
96
Real Time Temperature MSB[1]
18
Tx Bias L Alarm MSB[3]
97
Real Time Temperature LSB[1]
19
Tx Bias L Alarm LSB[3]
98
Real Time Vcc MSB[2]
20
Tx Bias H Warning MSB[3]
99
Real Time Vcc LSB[2]
21
Tx Bias H Warning LSB[3]
100
Real Time Tx Bias MSB[3]
22
Tx Bias L Warning MSB[3]
101
Real Time Tx Bias LSB[3]
23
Tx Bias L Warning LSB[3]
102
Real Time Tx Power MSB[4]
24
Tx Pwr H Alarm MSB[4]
103
Real Time Tx Power LSB[4]
25
Tx Pwr H Alarm LSB[4]
Notes:
1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256°C.
2. Supply Voltage (Vcc) is decoded as a 16 bit unsigned integer in increments of 100 µV.
3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 µA.
4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 µW.
5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 µW.
6. Bytes 55-94 are not intended for use with AFCT-57R5ATPZ, but have been set to default values per SFF-8472.
7. Byte 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment.
16
Table 14. EEPROM Serial ID Memory Contents – Soft Commands (Address A2h, Byte 110)
Bit #
Status/
Control Name
Description
Notes
7
TX_ DISABLE State
Digital state of SFP TX_ DISABLE Input Pin (1 = TX_DISABLE asserted)
Note 1
6
Soft TX_ DISABLE
Read/write bit for changing digital state of TX_DISABLE function
Note 1, 2
5
Reserved
4
Reserved
3
Reserved
2
TX_FAULT State
Digital state of the SFP TX_FAULT output pin (1 = TX_FAULT asserted)
Note 1
1
RX_LOS State
Digital state of the SFP RX_LOS output pin (1 = RX_LOS asserted)
Note 1
0
Data Ready (Bar)
Indicates transceiver is powered and real time sense data is ready. (0 = Ready)
Note 1
Notes:
1. The response time for soft commands of the AFCT-57R5ATPZ is 100 msec as specified by the MSA SFF-8472.
2. Bit 6 is logic OR’d with the SFP TX_DISABLE input pin 3 ... either asserted will disable the SFP transmitter.
Table 15. EEPROM Serial ID Memory Contents – Alarms and Warnings (Address A2h, Bytes 112, 113, 116, 117)
Byte
Bit
Flag Bit Name
Description
112
7
Temp High Alarm
Set when transceiver internal temperature exceeds high alarm threshold
6
Temp Low Alarm
Set when transceiver internal temperature exceeds low alarm threshold
5
Vcc High Alarm
Set when transceiver internal supply voltage exceeds high alarm threshold
4
Vcc Low Alarm
Set when transceiver internal supply voltage exceeds low alarm threshold
3
Tx Bias High Alarm
Set when transceiver laser bias current exceeds high alarm threshold
2
Tx Bias Low Alarm
Set when transceiver laser bias current exceeds low alarm threshold
1
Tx Power High Alarm
Set when transmitted average optical power exceeds high alarm threshold
0
Tx Power Low Alarm
Set when transmitted average optical power exceeds low alarm threshold
7
Rx Power High Alarm
Set when received optical power exceeds high alarm threshold
6
Rx Power Low Alarm
Set when received optical power exceeds low alarm threshold
0-5
Reserved
7
Temp High Warning
Set when transceiver internal temperature exceeds high warning threshold
6
Temp Low Warning
Set when transceiver internal temperature exceeds low warning threshold
5
Vcc High Warning
Set when transceiver internal supply voltage exceeds high warning threshold
4
Vcc Low Warning
Set when transceiver internal supply voltage exceeds low warning threshold
3
Tx Bias High Warning
Set when transceiver laser bias current exceeds high warning threshold
2
Tx Bias Low Warning
Set when transceiver laser bias current exceeds low warning threshold
1
Tx Power High Warning
Set when transmitted average optical power exceeds high warning threshold
0
Tx Power Low Warning
Set when transmitted average optical power exceeds low warning threshold
7
Rx Power High Warning
Set when received optical power exceeds high warning threshold
6
Rx Power Low Warning
Set when received optical power exceeds low warning threshold
0-5
Reserved
113
116
117
17
850 nm
850
Figure 5. Module drawing.
18
nm
X
Y
34.5
10
3x
10x ∅1.05 ± 0.01
∅ 0.1 L X A S
16.25
MIN. PITCH
7.2
7.1
2.5
B
PCB
EDGE
∅ 0.85 ± 0.05
∅ 0.1 S X Y
A
1
2.5
1
3.68
5.68
20
PIN 1
8.58
2x 1.7
11.08
16.25
REF. 14.25
8.48
9.6
4.8
11
10
11.93
SEE DETAIL 1
2.0
11x
11x 2.0
9x 0.95 ± 0.05
∅ 0.1 L X A S
5
26.8
2
10
3x
3
41.3
42.3
5
3.2
0.9
LEGEND
20
PIN 1
10.53
10.93
9.6
20x 0.5 ± 0.03
0.06 L A S B S
11.93
0.8
TYP.
1. PADS AND VIAS ARE CHASSIS GROUND
2. THROUGH HOLES, PLATING OPTIONAL
11
10
3. HATCHED AREA DENOTES COMPONENT
AND TRACE KEEPOUT (EXCEPT
CHASSIS GROUND)
4
2 ± 0.005 TYP.
0.06 L A S B S
2x 1.55 ± 0.05
∅ 0.1 L A S B S
DETAIL 1
Figure 6. SFP host board mechanical layout.
19
4. AREA DENOTES COMPONENT
KEEPOUT (TRACES ALLOWED)
DIMENSIONS ARE IN MILLIMETERS
1.7 ± 0.9
3.5 ± 0.3
41.78 ± 0.5
Tcase REFERENCE POINT
CAGE ASSEMBLY
15 MAX.
11.73 REF
15.25 ± 0.1
9.8 MAX.
10 REF
(to PCB)
10.4 ± 0.1
PCB
0.4 ± 0.1
(below PCB)
16.25 ± 0.1 MIN. PITCH
DIMENSIONS ARE IN MILLIMETERS
Customer Manufacturing Processes
This module is pluggable and is
not designed for aqueous wash,
IR reflow, or wave soldering
processes.
Figure 7. SFP assembly drawing.
For product information and a complete list of distributors, please go to our website:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.
Data subject to change. Copyright © 2007 Avago Technologies Limited. All rights reserved. Obsoletes AV01-0436EN
AV02-0435EN May 15, 2007
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement