EQ EPSILON5 Lf 250213

Portable
Portable ISP
ISPProgrammer
Programmer
for
for Field-Service
Field-Serviceand
and
Production
Production applications
applications
The EPSILON5 programmer being
used in Standalone Mode
The EPSILON5 is a high-speed portable ISP programmer designed for field
and low-volume production programming applications. The programmer supports
programming of many in-system programmable (ISP) microcontrollers
including AVR, 8051, ARM and Zensys Z-wave devices. It can be operated under
PC control during development and for project configuration / uploading using
the EQTools Toolsuite. For field / production applications the unit is designed to
operate in ‘Standalone Mode’. A ‘Standalone Programming Project’
can be recalled from the on-board non-volatile FLASH memory and programmed
into a Target System by pressing a single key. All the popular ISP connection
headers are catered for.
●● Portable In-System (ISP) Programmer
●● Ideal for Field-service or low-volume Production programming
applications
●● Supports In-system Programming (ISP) of many different programmable
microcontrollers and serial memory devices
●● Supports programming via SPI, JTAG, I2C and UART interfaces
●● Supports ‘Standalone’ operation (single project only) - no PC required
after programmer has been configured
●● Low power consumption allows the programmer to be powered from
most Target Systems (no external supply required)
FIELD-SERVICE
PRODUCTION PROGRAMMING
TARGET POWERED
FIRMWARE UPGRADEABLE
Control methods:
●● PC control via RS232 port (supplied with
for ATtiny HV devices
J3 Atmel
6-way Header
J6 Equinox
10-way Header
Pin 1
Pin 1
Pin 1
Programmer
ISP Connectors
J8 JTAG
10-way Header
Pin 1
J7 Atmel
10-way Header
Target Vcc
interfaces / protocols including JTAG, SPI,
I2C, ATtiny AVR HV mode, 8051 UART
Bootloader
●● Very fast programming speeds suitable for
high-throughput production environments
●● Robust I/O driver stage with ESD protection
●● Individually configurable programmer I/O
pins
●● User-configurable RESET pin state and
timing to cater for complicated RESET
circuits / RESET monitoring ICs
●● Supports programming of target ICs
between 3.0 and 5.0V.
●● Programmable frequency generator output
on SCK2 pin - supports external clocking
of AVR microcontrollers to speed up
programming
ISP connectors / headers:
●● Most popular ISP connectors are catered for
●● ARM standard 20-pin and 10-pin JTAG
User
Target
System
connectors requires a special ‘ARM JTAG
cable’ (available separately)
Software (as standard):
USB to Serial converter cable)
(Standalone Mode)
ISP Cable
Equinox Header
(10-way)
Atmel Header
(6-way)
JTAG Header
(10-way)
●● Manual operator control via 2-button keypad ●● EQTools - creates ‘Standalone
Target
Microcontroller
0V
●● Supports most ISP hardware
●● Power supply is reverse-polarity protected
●● Fixed +12V Target VPP voltage generator
SCK2
Programming Interfaces:
Atmel Header
(10-way)
Programming Projects’
Standalone Mode:
●● EDS - Development Mode for testing under
Programming Projects’ into the
programmer memory (512 kbytes capacity)
●● Single-button auto-program operation
allows repetitive execution of the project
(permanently stored in programmer)
●● PASS / BUSY / FAIL LED’s indicate
programmer status
●● Upload Wizard - uploads projects to the
PC control
●● Supports loading of 1 x ‘Standalone
programmer
Typical applications:
Programmer
●● Field-service programming
●● Low to medium quantity standalone
production programming
Device support:
Serial Cable
Power
Supply
Unit (PSU)
PC
●● Atmel AVR (not XMEGA or ATtiny TPI)
●● ARM FLASH microcontrollers -
Typical programmer connection to PC and
Target System
ARM7TDMI®, Cortex M0, Cortex M3,
Cortex M4
●● Selected 8051 FLASH microcontrollers
●● Serial EEPROMs (I2C)
●● Zensys Z-wave devices
Power supply:
●● The programmer can be powered from:
- User Target System (3.1 - 5.0V @ 60mA)
- External power supply via jack socket
(3.1 - 5.0V @ 60mA)
System Contents:
The picture shows the typical contents of the
Epsilon5 MkIII programming kit. An external
power supply is NOT included with the kit.
RS-232 External DC
port (J5) Power Supply
Input (CON1)
Bottom panel connections
Ordering information:
EPSILON5-A1 - Portable ISP Programmer (standard device support version)
EPSILON5(AVR-JTAG)-
Portable ISP Programmer - Atmel AVR - JTAG algorithms only
EPSILON5(ARM)-
Portable ISP Programmer - for Atmel ARM Microcontrollers
EPSILON5(E2)-
Portable ISP Programmer for Serial EEPROM Memory Devices (I2C only)
EPS-AVRJTAG-BUNDLE-Portable ISP Programmer and Atmel Atmega AVR JTAG Upgrade bundle
Equinox Technologies reserves the right to change any information contained within this leaflet without prior notice. E&OE
Telephone: +44 (0)1942 841975
:
Equinox House, 217 Church Street Westhoughton, Bolton, Lancashire BL5 3SW United Kingdom
Fax: +44 (0)1942 844181 : Email: [email protected] : Web: www.equinox-tech.com

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project